Discussion 4
1- AL JOHARA
In 1994 the European Channel Tunnel was opened, and it linked the European continent and Britain. It is a 31-mile tunnel carrying freight trains and Eurostar trains between Paris and London and is today considered the fast and modern transport institution. Although the tunnel traces its background to the 19th century, it is considered an achievement of the 20th century (Syon, 2008).
Though the project has been credited to be a success, the size of the channel had intrinsic uncertainties and risks. Tunneling projects are naturally high risk and often end up in high overrun on budget and completion dates due to the underground setting that were not anticipated during the contract (Syon, 2008). The risks present in the Chunnel project were design and construction challenges brought about by the changing geological situations, the third-party issues, the safety of the workers, infrastructure/property damage and environmental risk (Berend, 2016). In Britain there was no space for disposing of spoil and emission of waste became a significant challenge. Though there was a mitigation of disposing spoil in the Coast, some critiques were of the view that it would destroy the environment. The risk of the tunnel collapsing due to earthquakes was a concern to many individuals; however, the tunnels had a design which ensured they were resistant and caution was taken to reduce possibility of damage to equipment installed in them and to make sure entrances couldn’t be blocked by local collapses and landslips (Pireddu, 2017).
Technological risks were experienced in the construction of the tunnel. These include the political and economical viability of the machinery that were required to ensure the project goals were achieved. In the Chunnel tunnel, this risk was mainly assumed by the contractor, Eurotunnel. All the technological risks involved were mitigated by the comprehensive geological research of the strata of where the tunnel was to be constructed (Berend, 2016). Earlier concerns demanded the state of the art equipment which were costly and afterward found unnecessary. The political risks were mitigated by assigning the task to a private investor after the conservative and left-wing reign in Britain (Pireddu, 2017).
The project further experienced credit risk. The risk calculated on the basis of the investor’s creditworthiness. Unlike other mega-projects which are normally funded by the government, the Channel tunnel was private-funded and therefore presented a high risk to the contractors and investors. Most private investors were giving a small fraction of the total approximation cost. The administration for example under credit limitation had to suggest lump-sum contracts, which were impractical for such projects. Litigation and claims at the end of the project were experienced (Berend, 2016).
2- Fahad ALMahmoud
One of the risks that the English tunnel faced is aerodynamic of the tunnel, the designers have found .
IRJET- Systematic Prevention and Repair of Potholes in Flexible PavementIRJET Journal
This document discusses systematic prevention and repair of potholes in flexible pavement. It begins by defining potholes and describing their causes, such as poor drainage, inadequate pavement strength, and traffic loading. It then outlines a methodology to understand factors leading to pothole formation, including environmental, structural, traffic, construction, and maintenance quality issues. Prevention techniques like fog sealing are described to seal surfaces and prevent water infiltration. Repair methods like the throw and roll, semi-permanent, spray injection, and overlay techniques are also summarized. The document concludes by expecting the outcomes of introducing plastic and fly ash in bitumen to be cost reduction, better waste disposal, and reduced need for future maintenance.
IRJET- Systematic Prevention and Repair of Potholes in Flexible PavementIRJET Journal
This document discusses systematic prevention and repair of potholes in flexible pavement. It begins by defining potholes and describing how they form due to factors like inadequate pavement strength and the presence of water. Left unrepaired, potholes can lead to issues like accidents and increased vehicle maintenance costs. The document then examines various prevention techniques, such as fog sealing, to protect pavement surfaces from damage. It also outlines different repair methods for potholes, including throw and roll, semi-permanent fixes, spray injection, and overlays. The methodology proposed mixes plastics and fly ash with hot asphalt to create cheaper patching material while still providing durable repairs. In conclusion, using alternative materials can reduce repair costs while systematically addressing
The document summarizes the development of the Airbus A380 aircraft. It involved 39 companies from 16 countries and major manufacturing in Western Europe. While the aircraft achieved some goals like lower operating costs and environmental friendliness, the project struggled with delays, cost overruns, and communication issues between partners. An evaluation of the project's management found issues in areas like time management, communication management, and stakeholder management that contributed to challenges bringing the aircraft to market on schedule and budget.
The document is a report on an industrial training project at a hospital construction site in Chennai by URC Constructions Private Limited. It provides details of the project such as constructing a basement parking facility, 8 floors and other areas on a site located in Perungudi, Chennai. It describes the soil conditions, foundation design, construction stages, safety measures, and estimates for the project. The traineeship provided hands-on experience in construction practices, challenges, and learning.
Development Of Tipper Unloading MechanismIRJET Journal
1. The document describes the development of a tipper unloading mechanism to allow a tipper truck to unload material in multiple directions rather than just the rear.
2. Currently, tipper trucks can only unload material out the back, which reduces efficiency when precise unloading locations are required. It also requires the truck be parked in certain positions.
3. The proposed design involves adding two additional hydraulic cylinders on the sides of the tipper bed, allowing material to be unloaded to the left or right as well as the rear. This would provide more flexibility in unloading location without repositioning the truck.
4. Calculations are provided for the existing rear unloading mechanism involving the hydraulic cylinder, motor,
This document provides information about the CL 380 Construction Technology course, including details about credits, teaching scheme, pedagogy, and introduction. It discusses requirements for construction equipment, considerations for equipment selection, classification of equipment by type of work and function. It also covers engineering fundamentals of construction materials like soil and rock, including concepts like phase diagram, density, water content and volumetric measures. Finally, it discusses machine power requirements and factors like payload and power needed for equipment operation.
This document discusses key steps to reduce costs, risks, and uncertainties for offshore wind power project development in Southeast European economies. It identifies several challenges including high upfront costs, technical difficulties of operating in marine environments, and uncertainties around wind resource assessment and production levels. The document recommends using innovative IT tools and standardized methodologies to help optimize project layouts, conduct financial modeling, and identify and mitigate risks throughout the development process to improve the viability and bankability of offshore wind projects.
IRJET- Systematic Prevention and Repair of Potholes in Flexible PavementIRJET Journal
This document discusses systematic prevention and repair of potholes in flexible pavement. It begins by defining potholes and describing their causes, such as poor drainage, inadequate pavement strength, and traffic loading. It then outlines a methodology to understand factors leading to pothole formation, including environmental, structural, traffic, construction, and maintenance quality issues. Prevention techniques like fog sealing are described to seal surfaces and prevent water infiltration. Repair methods like the throw and roll, semi-permanent, spray injection, and overlay techniques are also summarized. The document concludes by expecting the outcomes of introducing plastic and fly ash in bitumen to be cost reduction, better waste disposal, and reduced need for future maintenance.
IRJET- Systematic Prevention and Repair of Potholes in Flexible PavementIRJET Journal
This document discusses systematic prevention and repair of potholes in flexible pavement. It begins by defining potholes and describing how they form due to factors like inadequate pavement strength and the presence of water. Left unrepaired, potholes can lead to issues like accidents and increased vehicle maintenance costs. The document then examines various prevention techniques, such as fog sealing, to protect pavement surfaces from damage. It also outlines different repair methods for potholes, including throw and roll, semi-permanent fixes, spray injection, and overlays. The methodology proposed mixes plastics and fly ash with hot asphalt to create cheaper patching material while still providing durable repairs. In conclusion, using alternative materials can reduce repair costs while systematically addressing
The document summarizes the development of the Airbus A380 aircraft. It involved 39 companies from 16 countries and major manufacturing in Western Europe. While the aircraft achieved some goals like lower operating costs and environmental friendliness, the project struggled with delays, cost overruns, and communication issues between partners. An evaluation of the project's management found issues in areas like time management, communication management, and stakeholder management that contributed to challenges bringing the aircraft to market on schedule and budget.
The document is a report on an industrial training project at a hospital construction site in Chennai by URC Constructions Private Limited. It provides details of the project such as constructing a basement parking facility, 8 floors and other areas on a site located in Perungudi, Chennai. It describes the soil conditions, foundation design, construction stages, safety measures, and estimates for the project. The traineeship provided hands-on experience in construction practices, challenges, and learning.
Development Of Tipper Unloading MechanismIRJET Journal
1. The document describes the development of a tipper unloading mechanism to allow a tipper truck to unload material in multiple directions rather than just the rear.
2. Currently, tipper trucks can only unload material out the back, which reduces efficiency when precise unloading locations are required. It also requires the truck be parked in certain positions.
3. The proposed design involves adding two additional hydraulic cylinders on the sides of the tipper bed, allowing material to be unloaded to the left or right as well as the rear. This would provide more flexibility in unloading location without repositioning the truck.
4. Calculations are provided for the existing rear unloading mechanism involving the hydraulic cylinder, motor,
This document provides information about the CL 380 Construction Technology course, including details about credits, teaching scheme, pedagogy, and introduction. It discusses requirements for construction equipment, considerations for equipment selection, classification of equipment by type of work and function. It also covers engineering fundamentals of construction materials like soil and rock, including concepts like phase diagram, density, water content and volumetric measures. Finally, it discusses machine power requirements and factors like payload and power needed for equipment operation.
This document discusses key steps to reduce costs, risks, and uncertainties for offshore wind power project development in Southeast European economies. It identifies several challenges including high upfront costs, technical difficulties of operating in marine environments, and uncertainties around wind resource assessment and production levels. The document recommends using innovative IT tools and standardized methodologies to help optimize project layouts, conduct financial modeling, and identify and mitigate risks throughout the development process to improve the viability and bankability of offshore wind projects.
This document provides a project report comparing techniques and methods for constructing elevated metro rail corridors in Delhi, India. It discusses various structural forms, construction methodologies, environmental impacts, and costs. The report finds that segmental construction using precast concrete segments is preferable to cast-in-situ construction as it allows for very fast progress, minimal traffic disruptions, and flexibility. Single segment girders for dual tracks have advantages over separate girders in terms of construction simplicity and aesthetics. Erection of viaducts is done using specialized launching gantries. Environmental impacts of construction like noise and vibration must be mitigated.
The document discusses developing a UAV system for the energy sector. It proposes using autonomous blimps that can refuel quadcopters in-flight, extending mission ranges. Initial interviews found energy companies interested in UAVs for inspections and monitoring. They suggested application areas and provided feedback. This led to modifying the prototype to include blimp-refueled quadcopters. The system is technically feasible and could efficiently execute various energy missions. A case study found the system could save a company over 25k euros per daily inspection mission compared to manned helicopters currently used. The energy sector in Greece represents a 100 million euro market for activities UAVs could assist with.
Introduction to advanced TUNNEL Formwork system: Case study of ‘Rohan - Abhi...IRJET Journal
This document provides an introduction to advanced tunnel formwork systems used in construction. It discusses:
- The benefits of tunnel formwork in reducing construction time and costs compared to traditional formwork methods.
- The key components of tunnel formwork systems including vertical panels, platforms, and props.
- How the tunnel formwork system allows continuous pouring of walls and slabs in one operation to achieve a 1-3 day slab cycle.
- A case study of a real estate project in Pune, India where tunnel formwork was used to construct high-rise apartment towers, reducing construction timelines.
- Conclusions that while tunnel formwork requires higher initial investment, it provides faster returns and overall becomes more economical
This whitepaper discusses cold in-place recycling with expanded asphalt mix (CIR EAM/FOAM) technology. Some key points:
- CIR EAM/FOAM involves milling off a portion of an existing asphalt layer, mixing it with a recycling agent (like asphalt emulsion or foamed asphalt) and additives, then compacting it to form a new base layer.
- It has significant environmental benefits like reusing existing materials, reducing waste and transportation needs. It also uses less energy than other rehabilitation methods.
- Structurally, it improves the recycled layer and helps prevent reflective cracking. Strength develops quickly when using foamed asphalt.
Airborne Wind Eenergy or also called high altitude wind energy systems are the most promising source of renewable energy and more cost-effective than conventional fossil fuel systems with the aim to achieve more sustainable forms of energy production.
1. The document discusses the syllabus for the Construction Technology course, which involves the study of construction methods, equipment, and temporary works.
2. It covers various types of construction equipment classified by function (excavating, hauling, etc.), operation type (intermittent, continuous), and availability (standard, special).
3. The selection of appropriate equipment is based on factors like job conditions, economic considerations, availability, and utilization. Understanding properties of construction materials like soil and rock is also important.
This document discusses airport planning and design. It provides information on various aspects of airport layout including typical layout configurations, key considerations for layout design such as independent taxiing operations and minimizing taxi distances, and characteristics of good airport layouts. It also discusses runway design standards per the ICAO, including runway dimensions and corrections required for factors like elevation, temperature, and slope gradient. Examples are provided on calculating corrected runway length based on standard formulas.
PII Paper for PetroMin Gas Pipeline ConferenceJohn Grover
Pipelines deteriorate over time due to corrosion and fatigue, threatening their integrity. To manage this risk, operators have implemented inspection and maintenance programs using intelligent pigs to detect corrosion. These programs were limited until PII pioneered Total Pipeline Integrity solutions combining affordable technology, methodology, and expertise. The paper discusses the history of pipeline inspection technology advances pioneered by PII, from the first magnetic flux tool in the 1970s to current tools, enabling operators to effectively manage pipeline integrity.
Palfinger provides innovative access and maintenance systems for the shipping and offshore industries. Their systems include Internal Tank Platforms (ITPs) for working inside cargo holds and tanks, Aerial Platforms for difficult to reach areas, and Hull Treatment Carrier systems for automated, environmentally friendly ship hull blasting and coating. The HTC systems can treat hulls faster and with significant reductions in paint usage, overspray, and environmental impact compared to conventional methods.
Graded unit Civil engineering PresentationTehmas Saeed
It was summary of Graded Unit Project of Steel Office Building HND project which i have finished in 2011, please note calculations and drawings are missing from this presentations as they were submitted earlier, however a copy may be available for new students from Glagsow kelvin college. Please ask Murdo or Maureen for that.
IRJET- Design of Box Culvert using Visual BasicIRJET Journal
This document describes the design of a box culvert using Visual Basic programming language. It begins with an abstract that outlines the purpose of developing a program for designing box culverts. It then provides background details on culverts and discusses the methodology, which includes surveying the site, selecting design loads, analyzing the culvert using STAAD Pro software, and developing the Visual Basic program. The document presents results of the STAAD Pro analysis, showing bending moments at centers and ends of the top slab and side walls for three loading cases. It also includes graphs and images from STAAD Pro. The conclusion discusses declaring variables, performing calculations, and displaying output strings in the Visual Basic program.
IRJET- Ground Water Control Method Simulation in Sphinx AreaIRJET Journal
This document summarizes a study on groundwater control methods to protect the Sphinx in Egypt from rising groundwater levels. It presents 5 alternatives that were modeled using Modflow software: 1) linear drains, 2) combined linear drains and barriers, 3) horizontal wells, 4) combined horizontal wells and barriers, 5) barriers. The study analyzed each alternative's ability to lower the water table, costs, drawbacks, and ranked them. It determined that linear drains and horizontal wells were the most economical and effective at lowering water levels to the target level of 12 meters above sea level, with linear drains ranked as the best option. The document provided conclusions and recommendations to preserve the Sphinx area based on the results of
This document discusses lessons learned from recent deepwater riser projects and how risers can become more standardized industrial products. It describes an industrialization process for risers involving a technical hierarchy to systematically organize components. This allows for detailed failure mode and effects analysis (FMECA) and structured engineering. An example FMECA is provided for a hybrid riser tower (HRT) system. The analysis identified 2 high risks related to connections at the top and bottom of the HRT, in line with reliability data. Overall the FMECA found 194 medium risks and 437 low risks. The document advocates standardizing key riser design aspects like materials to improve cost effectiveness while meeting functional requirements.
W.A.R.(waterabsorbingroad): New technique for road construction using permeab...SaurabhPawar76
This document presents a study on a new technique called Water Absorbing Road (W.A.R.) that uses permeable pavement for road construction. The study examines the use of permeable concrete, asphalt, and pavers that allow stormwater to enter and be filtered. Benefits include reduced runoff and flooding, improved water quality by trapping pollutants, and increased road safety and durability. The study tests compressive strengths of permeable and conventional concrete. Maintenance and costs are also compared. The research methodology examines hydrological and structural design. Potential benefits are groundwater recharge and reduced need for drainage systems, while challenges include needing specialized construction and potential clogging over time.
DMRC Summer internship report for civil engineering students.
Project- DMRC phase 3 (CC-34 & CC-32) Design and construction of tunnel and underground metro station
Optimizing completions in deviated and extended reach wells is a key to safe drilling and optimum
production, particularly in complex terrain and formations. This work summarizes the systematic methodology
and engineering process employed to identify and refine the highly effective completions solution used in ERW
completion system and install highly productive and robust hard wares in horizontal and Extended Reach Wells
for Oil and Gas. A case study of an offshore project was presented and discussed. The unique completion design,
pre-project evaluation and the integrated effort undertaken to firstly, minimize completion and formation damage.
Secondly, maximize gravel placement and sand control method .Thirdly, to maximize filter cake removal
efficiencies. The importance of completions technologies was identified and a robust tool was developed .More
importantly, the ways of deploying these tools to achieve optimal performance in ERW’s completions was done.
The application of the whole system will allow existing constraints to be challenged and overcome successfully;
these achievements was possible, by applying sound practical engineering principle and continuous optimization,
with respect to the rig and environmental limitation space and rig capacity.
Keywords: Well Completions , Deviated and Extended Rearch Wells , Optimization
This document discusses fuel saving devices that can be implemented in vehicles. It begins by introducing the topic and noting the increasing fuel usage due to rising vehicle numbers. It then describes different types of fuel saving devices like magnets, vapor devices, and electronic devices. It provides examples of how such devices can be implemented in vehicles and how they work, particularly magnetic fuel saver devices. It discusses the current scope of implementation, advantages like reduced pollution and optimized fuel usage, as well as future applications and disadvantages. It concludes that the initial costs are low while the long-term fuel savings and environmental benefits are significant.
IRJET- Analysis of Flood Resistant Rehab ShelterIRJET Journal
This document discusses the analysis of a flood resistant rehabilitation shelter design. It begins with an abstract that outlines an initiative to quickly rehouse people who have lost homes during floods. It then provides background on floods in India, the need for sustainable and flood-resistant development. The document describes the methodology, including specifications for a residential building design that can be constructed rapidly. It details the site investigation and plan for the building. Finally, it explains the structural analysis of the building design using STAAD Pro software.
Selection Criteria of Equipment in Construction ProjectIRJET Journal
This document discusses the selection criteria for construction equipment on projects. It begins by defining the importance of selecting the proper equipment, as this decision can impact time, cost and productivity. The document then outlines various types of earthmoving, concrete placing and lifting equipment commonly used. It describes factors that influence equipment choice, such as economic considerations, site conditions, manufacturer preferences, and labor availability. The selection process and specific criteria for different equipment types are also examined. Overall, the document provides guidance on strategically matching equipment to tasks to maximize efficiency during construction.
(APA 6th Edition Formatting and Style Guide)
Office of Graduate Studies
Alcorn State University
Engaging Possibilities, Pursuing Excellence
REVISED May 23, 2018
THESIS MANUAL
Graduates
2
COPYRIGHT PRIVILEGES
BELONG TO
OFFICE OF GRADUATE STUDIES
ALCORN STATE UNIVERSITY, LORMAN, MS
Reproduction for distribution of this THESIS MANUAL requires the written permission of the
Provost and Executive Vice President for Academic Affairs or Graduate Studies Administrator.
FOREWORD
Alcorn State University Office of Graduate Studies requires that all students comply with the
specifications given in this document in the publication of a thesis or non-thesis research project.
Graduate students, under faculty guidance, are expected to produce scholarly work either in the
form of a thesis or a scholarly research project.
The thesis (master or specialist) should document the student's research study and maintain a
degree of intensity.
The purpose of this manual is to assist the graduate student and the graduate thesis advisory
committee in each department with the instructions contained herein. This is the official
approved manual by the Graduate Division.
Formatting questions not addressed in these guidelines should be directed to the Graduate School
staff in the Walter Washington Administration Building, Suite 519 or by phone at
601.877.6122 or via email: [email protected] or in person.
The Graduate Studies
Thesis Advisory Committee
(Revised Spring 2018)
mailto:[email protected]
TABLE OF CONTENTS
Page
INTRODUCTION ............................................................................................................................ 3
SELECTION AND APPOINTMENT OF THESIS ADVISORY COMMITTEE ......................... 4
1. Early Topic Selection ......................................................................................................... 4
2. Selection of Thesis Chair ......................................................................................................... 4
3. Selection of Thesis Committee Members .......................................................................... 4
4. Appointment of Thesis Advisory Committee Form .......................................................... 4
5. Invitation to Prospective Committee Members ................................................................. 5
6. TAC Committee Selection ................................................................................................. 5
CHOICE OF SUBJECT .................................................................................................................... 5
PROPOSAL DEFENSE AND SUBMISSION OF PROPOSAL TO IRB ..................................... 5
PARTS OF THE MANUSCRIPT: PRELIMINARY PAGES ..................................................... 8
1. Title Page .
(a) Thrasymachus’ (the sophist’s) definition of Justice or Right o.docxAASTHA76
(a) Thrasymachus’ (the sophist’s) definition of Justice or Right or Right Doing/Living is “The Interest of the Stronger (Might makes Right).” How does Socrates refute this definition? (cite just
one
of his arguments) [cf:
The Republic
, 30-40, Unit 1 Lecture Video]
(b) According to Socrates, what is the true definition of Justice or Right? [cf:
The Republic
, 141-42, Unit 2 Lecture Video]
(c) And why therefore is the Just life far preferable to the Unjust life (142-43)?
(a) The Allegory of the CAVE (the main metaphor of western philosophy) is an illustration of the Divided LINE.
Characterize
the Two Worlds, and the move/ascent from one to the other (exiting the CAVE, crossing the Divided LINE)—which is alone the true meaning of Education and the only way to become Just, Right, and Immortal. [cf:
The Republic
, 227-232, Unit 3 Lecture Video]
(b) How do the philosophical Studies of
Arithmetic
(number) and
Dialectic
take you above the Divided Line and out of the changing sense-world of illusion (the CAVE) into Reality and make you use your Reason (pure thought) instead of your senses? [cf:
The Republic
, 235-37, 240-42, 250-55. Unit 4 Lecture Video (transcript)]
Give a summary of the
Proof of the Force
(Why there is the “Universe,” “Man,” “God,” “History,” etc)? Start with, “Can there be
nothing
?” [cf: TJH 78-95, Unit 2 Lecture Video]
NIETZSCHE is the crucial Jedi philosopher who provides the “bridge” between negative and positive Postmodernity by focusing on a certain “Problem” and the “
Solution
” to it.
(a) Discuss
2
of the following items (
1
pertaining to the Problem,
1
pertaining to the
.
More Related Content
Similar to Discussion 41- AL JOHARA In 1994 the European Channel Tun.docx
This document provides a project report comparing techniques and methods for constructing elevated metro rail corridors in Delhi, India. It discusses various structural forms, construction methodologies, environmental impacts, and costs. The report finds that segmental construction using precast concrete segments is preferable to cast-in-situ construction as it allows for very fast progress, minimal traffic disruptions, and flexibility. Single segment girders for dual tracks have advantages over separate girders in terms of construction simplicity and aesthetics. Erection of viaducts is done using specialized launching gantries. Environmental impacts of construction like noise and vibration must be mitigated.
The document discusses developing a UAV system for the energy sector. It proposes using autonomous blimps that can refuel quadcopters in-flight, extending mission ranges. Initial interviews found energy companies interested in UAVs for inspections and monitoring. They suggested application areas and provided feedback. This led to modifying the prototype to include blimp-refueled quadcopters. The system is technically feasible and could efficiently execute various energy missions. A case study found the system could save a company over 25k euros per daily inspection mission compared to manned helicopters currently used. The energy sector in Greece represents a 100 million euro market for activities UAVs could assist with.
Introduction to advanced TUNNEL Formwork system: Case study of ‘Rohan - Abhi...IRJET Journal
This document provides an introduction to advanced tunnel formwork systems used in construction. It discusses:
- The benefits of tunnel formwork in reducing construction time and costs compared to traditional formwork methods.
- The key components of tunnel formwork systems including vertical panels, platforms, and props.
- How the tunnel formwork system allows continuous pouring of walls and slabs in one operation to achieve a 1-3 day slab cycle.
- A case study of a real estate project in Pune, India where tunnel formwork was used to construct high-rise apartment towers, reducing construction timelines.
- Conclusions that while tunnel formwork requires higher initial investment, it provides faster returns and overall becomes more economical
This whitepaper discusses cold in-place recycling with expanded asphalt mix (CIR EAM/FOAM) technology. Some key points:
- CIR EAM/FOAM involves milling off a portion of an existing asphalt layer, mixing it with a recycling agent (like asphalt emulsion or foamed asphalt) and additives, then compacting it to form a new base layer.
- It has significant environmental benefits like reusing existing materials, reducing waste and transportation needs. It also uses less energy than other rehabilitation methods.
- Structurally, it improves the recycled layer and helps prevent reflective cracking. Strength develops quickly when using foamed asphalt.
Airborne Wind Eenergy or also called high altitude wind energy systems are the most promising source of renewable energy and more cost-effective than conventional fossil fuel systems with the aim to achieve more sustainable forms of energy production.
1. The document discusses the syllabus for the Construction Technology course, which involves the study of construction methods, equipment, and temporary works.
2. It covers various types of construction equipment classified by function (excavating, hauling, etc.), operation type (intermittent, continuous), and availability (standard, special).
3. The selection of appropriate equipment is based on factors like job conditions, economic considerations, availability, and utilization. Understanding properties of construction materials like soil and rock is also important.
This document discusses airport planning and design. It provides information on various aspects of airport layout including typical layout configurations, key considerations for layout design such as independent taxiing operations and minimizing taxi distances, and characteristics of good airport layouts. It also discusses runway design standards per the ICAO, including runway dimensions and corrections required for factors like elevation, temperature, and slope gradient. Examples are provided on calculating corrected runway length based on standard formulas.
PII Paper for PetroMin Gas Pipeline ConferenceJohn Grover
Pipelines deteriorate over time due to corrosion and fatigue, threatening their integrity. To manage this risk, operators have implemented inspection and maintenance programs using intelligent pigs to detect corrosion. These programs were limited until PII pioneered Total Pipeline Integrity solutions combining affordable technology, methodology, and expertise. The paper discusses the history of pipeline inspection technology advances pioneered by PII, from the first magnetic flux tool in the 1970s to current tools, enabling operators to effectively manage pipeline integrity.
Palfinger provides innovative access and maintenance systems for the shipping and offshore industries. Their systems include Internal Tank Platforms (ITPs) for working inside cargo holds and tanks, Aerial Platforms for difficult to reach areas, and Hull Treatment Carrier systems for automated, environmentally friendly ship hull blasting and coating. The HTC systems can treat hulls faster and with significant reductions in paint usage, overspray, and environmental impact compared to conventional methods.
Graded unit Civil engineering PresentationTehmas Saeed
It was summary of Graded Unit Project of Steel Office Building HND project which i have finished in 2011, please note calculations and drawings are missing from this presentations as they were submitted earlier, however a copy may be available for new students from Glagsow kelvin college. Please ask Murdo or Maureen for that.
IRJET- Design of Box Culvert using Visual BasicIRJET Journal
This document describes the design of a box culvert using Visual Basic programming language. It begins with an abstract that outlines the purpose of developing a program for designing box culverts. It then provides background details on culverts and discusses the methodology, which includes surveying the site, selecting design loads, analyzing the culvert using STAAD Pro software, and developing the Visual Basic program. The document presents results of the STAAD Pro analysis, showing bending moments at centers and ends of the top slab and side walls for three loading cases. It also includes graphs and images from STAAD Pro. The conclusion discusses declaring variables, performing calculations, and displaying output strings in the Visual Basic program.
IRJET- Ground Water Control Method Simulation in Sphinx AreaIRJET Journal
This document summarizes a study on groundwater control methods to protect the Sphinx in Egypt from rising groundwater levels. It presents 5 alternatives that were modeled using Modflow software: 1) linear drains, 2) combined linear drains and barriers, 3) horizontal wells, 4) combined horizontal wells and barriers, 5) barriers. The study analyzed each alternative's ability to lower the water table, costs, drawbacks, and ranked them. It determined that linear drains and horizontal wells were the most economical and effective at lowering water levels to the target level of 12 meters above sea level, with linear drains ranked as the best option. The document provided conclusions and recommendations to preserve the Sphinx area based on the results of
This document discusses lessons learned from recent deepwater riser projects and how risers can become more standardized industrial products. It describes an industrialization process for risers involving a technical hierarchy to systematically organize components. This allows for detailed failure mode and effects analysis (FMECA) and structured engineering. An example FMECA is provided for a hybrid riser tower (HRT) system. The analysis identified 2 high risks related to connections at the top and bottom of the HRT, in line with reliability data. Overall the FMECA found 194 medium risks and 437 low risks. The document advocates standardizing key riser design aspects like materials to improve cost effectiveness while meeting functional requirements.
W.A.R.(waterabsorbingroad): New technique for road construction using permeab...SaurabhPawar76
This document presents a study on a new technique called Water Absorbing Road (W.A.R.) that uses permeable pavement for road construction. The study examines the use of permeable concrete, asphalt, and pavers that allow stormwater to enter and be filtered. Benefits include reduced runoff and flooding, improved water quality by trapping pollutants, and increased road safety and durability. The study tests compressive strengths of permeable and conventional concrete. Maintenance and costs are also compared. The research methodology examines hydrological and structural design. Potential benefits are groundwater recharge and reduced need for drainage systems, while challenges include needing specialized construction and potential clogging over time.
DMRC Summer internship report for civil engineering students.
Project- DMRC phase 3 (CC-34 & CC-32) Design and construction of tunnel and underground metro station
Optimizing completions in deviated and extended reach wells is a key to safe drilling and optimum
production, particularly in complex terrain and formations. This work summarizes the systematic methodology
and engineering process employed to identify and refine the highly effective completions solution used in ERW
completion system and install highly productive and robust hard wares in horizontal and Extended Reach Wells
for Oil and Gas. A case study of an offshore project was presented and discussed. The unique completion design,
pre-project evaluation and the integrated effort undertaken to firstly, minimize completion and formation damage.
Secondly, maximize gravel placement and sand control method .Thirdly, to maximize filter cake removal
efficiencies. The importance of completions technologies was identified and a robust tool was developed .More
importantly, the ways of deploying these tools to achieve optimal performance in ERW’s completions was done.
The application of the whole system will allow existing constraints to be challenged and overcome successfully;
these achievements was possible, by applying sound practical engineering principle and continuous optimization,
with respect to the rig and environmental limitation space and rig capacity.
Keywords: Well Completions , Deviated and Extended Rearch Wells , Optimization
This document discusses fuel saving devices that can be implemented in vehicles. It begins by introducing the topic and noting the increasing fuel usage due to rising vehicle numbers. It then describes different types of fuel saving devices like magnets, vapor devices, and electronic devices. It provides examples of how such devices can be implemented in vehicles and how they work, particularly magnetic fuel saver devices. It discusses the current scope of implementation, advantages like reduced pollution and optimized fuel usage, as well as future applications and disadvantages. It concludes that the initial costs are low while the long-term fuel savings and environmental benefits are significant.
IRJET- Analysis of Flood Resistant Rehab ShelterIRJET Journal
This document discusses the analysis of a flood resistant rehabilitation shelter design. It begins with an abstract that outlines an initiative to quickly rehouse people who have lost homes during floods. It then provides background on floods in India, the need for sustainable and flood-resistant development. The document describes the methodology, including specifications for a residential building design that can be constructed rapidly. It details the site investigation and plan for the building. Finally, it explains the structural analysis of the building design using STAAD Pro software.
Selection Criteria of Equipment in Construction ProjectIRJET Journal
This document discusses the selection criteria for construction equipment on projects. It begins by defining the importance of selecting the proper equipment, as this decision can impact time, cost and productivity. The document then outlines various types of earthmoving, concrete placing and lifting equipment commonly used. It describes factors that influence equipment choice, such as economic considerations, site conditions, manufacturer preferences, and labor availability. The selection process and specific criteria for different equipment types are also examined. Overall, the document provides guidance on strategically matching equipment to tasks to maximize efficiency during construction.
Similar to Discussion 41- AL JOHARA In 1994 the European Channel Tun.docx (20)
(APA 6th Edition Formatting and Style Guide)
Office of Graduate Studies
Alcorn State University
Engaging Possibilities, Pursuing Excellence
REVISED May 23, 2018
THESIS MANUAL
Graduates
2
COPYRIGHT PRIVILEGES
BELONG TO
OFFICE OF GRADUATE STUDIES
ALCORN STATE UNIVERSITY, LORMAN, MS
Reproduction for distribution of this THESIS MANUAL requires the written permission of the
Provost and Executive Vice President for Academic Affairs or Graduate Studies Administrator.
FOREWORD
Alcorn State University Office of Graduate Studies requires that all students comply with the
specifications given in this document in the publication of a thesis or non-thesis research project.
Graduate students, under faculty guidance, are expected to produce scholarly work either in the
form of a thesis or a scholarly research project.
The thesis (master or specialist) should document the student's research study and maintain a
degree of intensity.
The purpose of this manual is to assist the graduate student and the graduate thesis advisory
committee in each department with the instructions contained herein. This is the official
approved manual by the Graduate Division.
Formatting questions not addressed in these guidelines should be directed to the Graduate School
staff in the Walter Washington Administration Building, Suite 519 or by phone at
601.877.6122 or via email: [email protected] or in person.
The Graduate Studies
Thesis Advisory Committee
(Revised Spring 2018)
mailto:[email protected]
TABLE OF CONTENTS
Page
INTRODUCTION ............................................................................................................................ 3
SELECTION AND APPOINTMENT OF THESIS ADVISORY COMMITTEE ......................... 4
1. Early Topic Selection ......................................................................................................... 4
2. Selection of Thesis Chair ......................................................................................................... 4
3. Selection of Thesis Committee Members .......................................................................... 4
4. Appointment of Thesis Advisory Committee Form .......................................................... 4
5. Invitation to Prospective Committee Members ................................................................. 5
6. TAC Committee Selection ................................................................................................. 5
CHOICE OF SUBJECT .................................................................................................................... 5
PROPOSAL DEFENSE AND SUBMISSION OF PROPOSAL TO IRB ..................................... 5
PARTS OF THE MANUSCRIPT: PRELIMINARY PAGES ..................................................... 8
1. Title Page .
(a) Thrasymachus’ (the sophist’s) definition of Justice or Right o.docxAASTHA76
(a) Thrasymachus’ (the sophist’s) definition of Justice or Right or Right Doing/Living is “The Interest of the Stronger (Might makes Right).” How does Socrates refute this definition? (cite just
one
of his arguments) [cf:
The Republic
, 30-40, Unit 1 Lecture Video]
(b) According to Socrates, what is the true definition of Justice or Right? [cf:
The Republic
, 141-42, Unit 2 Lecture Video]
(c) And why therefore is the Just life far preferable to the Unjust life (142-43)?
(a) The Allegory of the CAVE (the main metaphor of western philosophy) is an illustration of the Divided LINE.
Characterize
the Two Worlds, and the move/ascent from one to the other (exiting the CAVE, crossing the Divided LINE)—which is alone the true meaning of Education and the only way to become Just, Right, and Immortal. [cf:
The Republic
, 227-232, Unit 3 Lecture Video]
(b) How do the philosophical Studies of
Arithmetic
(number) and
Dialectic
take you above the Divided Line and out of the changing sense-world of illusion (the CAVE) into Reality and make you use your Reason (pure thought) instead of your senses? [cf:
The Republic
, 235-37, 240-42, 250-55. Unit 4 Lecture Video (transcript)]
Give a summary of the
Proof of the Force
(Why there is the “Universe,” “Man,” “God,” “History,” etc)? Start with, “Can there be
nothing
?” [cf: TJH 78-95, Unit 2 Lecture Video]
NIETZSCHE is the crucial Jedi philosopher who provides the “bridge” between negative and positive Postmodernity by focusing on a certain “Problem” and the “
Solution
” to it.
(a) Discuss
2
of the following items (
1
pertaining to the Problem,
1
pertaining to the
.
(Glossary of Telemedicine and eHealth)· Teleconsultation Cons.docxAASTHA76
(Glossary of Telemedicine and eHealth)
· Teleconsultation: Consultation between a provider and specialist at distance using either store and forward telemedicine or real time videoconferencing.
· Telehealth and Telemedicine: Telemedicine is the use of medical information exchanged from one site to another via electronic communications to improve patients' health status. Closely associated with telemedicine is the term "telehealth," which is often used to encompass a broader definition of remote healthcare that does not always involve clinical services. Videoconferencing, transmission of still images, e-health including patient portals, remote monitoring of vital signs, continuing medical education and nursing call centers are all considered part of telemedicine and telehealth. Telemedicine is not a separate medical specialty. Products and services related to telemedicine are often part of a larger investment by health care institutions in either information technology or the delivery of clinical care. Even in the reimbursement fee structure, there is usually no distinction made between services provided on site and those provided through telemedicine and often no separate coding required for billing of remote services. Telemedicine encompasses different types of programs and services provided for the patient. Each component involves different providers and consumers.
· TeleICU: TeleICU is a collaborative, interprofessional model focusing on the care of critically ill patients using telehealth technologies.
· Telemonitoring: The process of using audio, video, and other telecommunications and electronic information processing technologies to monitor the health status of a patient from a distance.
· Telemonitoring: The process of using audio, video, and other telecommunications and electronic information processing technologies to monitor the health status of a patient from a distance.
· Clinical Decision Support System (CCDS): Systems (usually electronically based and interactive) that provide clinicians, staff, patients, and other individuals with knowledge and person-specific information, intelligently filtered and presented at appropriate times, to enhance health and health care. (http://healthit.ahrq.gov/images/jun09cdsreview/09_0069_ef.html)
· e-Prescribing: The electronic generation, transmission and filling of a medical prescription, as opposed to traditional paper and faxed prescriptions. E-prescribing allows for qualified healthcare personnel to transmit a new prescription or renewal authorization to a community or mail-order pharmacy.
· Home Health Care and Remote Monitoring Systems: Care provided to individuals and families in their place of residence for promoting, maintaining, or restoring health or for minimizing the effects of disability and illness, including terminal illness. In the Medicare Current Beneficiary Survey and Medicare claims and enrollment data, home health care refers to home visits by professionals including nu.
(Assmt 1; Week 3 paper) Using ecree Doing the paper and s.docxAASTHA76
The document provides instructions for students on completing Assignment 1 for an online history course. It explains how to access and submit the assignment through the ecree online platform. Students are instructed to write a 2-page paper in 4 parts addressing how diversity was dealt with in America from 1865 to the 1920s. The document provides a sample paper format and emphasizes including an introduction with thesis, 3 examples supporting the thesis, consideration of an opposing view, and conclusion relating the topic to modern times. Sources must be cited within the paper and listed at the end using the SWS format.
(Image retrieved at httpswww.google.comsearchhl=en&biw=122.docxAASTHA76
(Image retrieved at https://www.google.com/search?hl=en&biw=1229&bih=568&tbm=isch&sa=1&ei=fmYIW9W3G6jH5gLn7IHYAQ&q=analysis&oq=analysis&gs_l=img.3..0i67k1l2j0l5j0i67k1l2j0.967865.968569.0.969181.7.4.0.0.0.0.457.682.1j1j4-1.3.0....0...1c.1.64.img..5.2.622...0i7i30k1.0.rL9KcsvXM1U#imgrc=LU1vXlB6e2doDM: / )
ESOL 052 (Essay #__)
Steps:
1. Discuss the readings, videos, and photographs in the Truth and Lies module on Bb.
2. Select a significant/controversial photograph to analyze. (The photograph does not have to be from Bb.)
3. Choose one of the following essay questions:
a. What truth does this photograph reveal?
b. What lie does this photograph promote?
c. Why/How did people deliberately misuse this photograph and distort its true meaning?
d. Why was this photograph misinterpreted by so many people?
e. Why do so many people have different reactions to this photograph?
f. ___________________________________________________________________________?
(Students may create their own visual analysis essay question as long as it is pre-approved by the instructor.)
4. Use the OPTIC chart to brainstorm and take notes on your photograph.
5. Use a pre-writing strategy (outline, graphic organizer, etc.) to organize your ideas.
6. Using correct MLA format, write a 3-5 page essay.
7. Type a Works Cited page. (Use citationmachine.net, easybib.com, etc. to format your info.)
8. Peer and self-edit during the writing process (Bb Wiki, in/outside class).
9. Get feedback from your peers and an instructor during the writing process.
(Note: Students who visit the Writing Center and show me proof get 2 additional days to work on the assignment.)
10. Proofread/edit/revise during the writing process.
11. Put your pre-writing, essay, and Works Cited page in 1 Word document and upload it on Bb by midnight on ______. (If a student submits an essay without pre-writing or without a Works Cited page, he/she will receive a zero. If a student submits an assignment late, he/she will receive a zero. If a student plagiarizes, he/she will receive a zero.)
Purpose: Students will be able to use their reading, writing, critical thinking, and research skills to conduct a visual analysis that explores the theme of Truth and Lies.
Tone: The tone of this assignment should be formal and academic.
Language: The diction and syntax of this assignment should be formal and academic. Students should not use second person pronouns (you/your), contractions, abbreviations, slang, or any type of casual language. Students should refer to the diction and syntax guidelines in the writing packet.
Audience: The audience of this assignment is the student’s peers and instructor.
Format: MLA style (double spaced, 1 in. margins, Times New Roman 12 font, pagination, heading, title, tab for each paragraph, in-text citations, Works Cited page, hanging indents, etc.)
Requirements:
In order for a student to earn a minimum passing grade of 70% on this assignment, h.
(Dis) Placing Culture and Cultural Space Chapter 4.docxAASTHA76
(Dis) Placing Culture and Cultural Space
Chapter 4
+
Chapter Objectives
Describe the relationships among culture, place, cultural space, and identity in the context of globalization.
Explain how people use communicative practices to construct, maintain, negotiate, and hybridize cultural spaces.
Explain how cultures are simultaneously placed and displaced in the global context leading to segregated, contested and hybrid cultural spaces.
Describe the practice of bifocal vision to highlight the linkages between “here” and “there” as well as the connections between present and past.
+
Introduction
Explore the cultural and intercultural communication dimensions of place, space and location. We will examine:
The dynamic process of placing and displacing cultural space in the context of globalization.
How people use communicative practices to construct, maintain, negotiate, and hybridize cultural spaces
How segregated, contested, and hybrid cultural spaces are both shaped by the legacy of colonialism and the context of globalization.
How Hip hop culture illustrates the cultural and intercultural dimensions of place, space, and location in the context of globalization
+
Placing Culture and Cultural Space
Culture, by definition, is rooted in place with a reciprocal relationship between people and place
Culture:
“Place tilled” in Middle English
Colere : “to inhabit, care for, till, worship” in Latin
In the context of globalization, what is the relationship between culture and place?
Culture is both placed and displaced
+
Cultural Space
The communicative practices that construct meanings in, through and about particular places
Cultural space shapes verbal and nonverbal communicative practices
i.e. Classrooms, dance club, library.
Cultural spaces are constructed through the communicative practices developed and lived by people in particular places
Communicative practices include:
The languages, accents, slang, dress, artifacts, architectural design, the behaviors and patterns of interaction, the stories, the discourses and histories
How is the cultural space of your home, neighborhood, city, and state constructed through communicative practices?
+
Place, Cultural Space and Identity
Place, Culture, Identity and Difference
What’s the relationship between place and identity?
Avowed identity:
The way we see, label and make meaning about ourselves and
Ascribed identity:
The way others view, name and describe us and our group
Examples of how avowed and ascribed identities may conflict?
How is place related to standpoint and power?
Locations of enunciation:
Sites or positions from which to speak.
A platform from which to voice a perspective and be heard and/or silenced.
+
Displacing Culture and Cultural Space
(Dis) placed culture and cultural space:
A notion that captures the complex, contradictory and contested nature of cultural space and the relationship between culture and place that has emerged in the context o.
(1) Define the time value of money. Do you believe that the ave.docxAASTHA76
(1) Define the time value of money. Do you believe that the average person considers the time value of money when they make investment decisions? Please explain.
(2) Distinguish between ordinary annuities and annuities due. Also, distinguish between the future value of an annuity and the present value of an annuity.
.
(chapter taken from Learning Power)From Social Class and t.docxAASTHA76
This document summarizes Jean Anyon's observations of 5 elementary schools that served different socioeconomic classes. In working-class schools, classroom activities focused on rote memorization and following procedures without explanation of underlying concepts. Work involved copying steps and notes from the board. In contrast, more affluent schools emphasized conceptual learning, creativity, and preparing students for professional careers through activities like experiments and projects. Anyon concluded schools were preparing students for different roles in the economy and society based on their social class.
(Accessible at httpswww.hatchforgood.orgexplore102nonpro.docxAASTHA76
(Accessible at https://www.hatchforgood.org/explore/102/nonprofit-photography-ethics-and-approaches)
Nonprofit Photography: Ethics
and Approaches
Best practices and tips on ethics and approaches in
humanitarian photography for social impact.
The first moon landing. The Vietnamese ‘napalm girl’, running naked and in agony. The World
Trade Centers falling.
As we know, photography carries the power to inspire, educate, horrify and compel its viewers to
take action. Images evoke strong and often public emotions, as people frequently formulate their
opinions, judgments and behaviors in response to visual stimuli. Because of this, photography
can wield substantial control over public perception and discourse.
Moreover, photography in our digital age permits us to deliver complex information about
remote conditions which can be rapidly distributed and effortlessly processed by the viewer.
Recently, we’ve witnessed the profound impact of photography coupled with social media:
together, they have fueled political movements and brought down a corrupt government.
Photography can - and has - changed the course of history.
Ethical Considerations
Those who commission and create photography of marginalized populations to further an
organizations’ mission possess a tremendous responsibility. Careful ethical consideration should
be given to all aspects of the photography supply chain: its planning, creation, and distribution.
When planning a photography campaign, it is important to examine the motives for creating
particular images and their potential impact. Not only must a faithful, comprehensive visual
depiction of the subjects be created to avoid causing misconception, but more importantly, the
subjects’ dignity must be preserved. Words and images that elicit an emotional response by their
sheer shock value (e.g. starving, skeletal children covered in flies) are harmful because they
exploit the subjects’ condition in order to generate sympathy for increasing charitable donations
or support for a given cause. In addition to violating privacy and human rights, this so-called
'poverty porn’ is harmful to those it is trying to aid because it evokes the idea that the
marginalized are helpless and incapable of helping themselves, thereby cultivating a culture of
paternalism. Poverty porn is also detrimental because it is degrading, dishonoring and robs
people of their dignity. While it is important to illustrate the challenges of a population, one must
always strive to tell stories in a way that honors the subjects’ circumstances, and (ideally)
illustrates hope for their plight.
Legal issues
Legal issues are more clear cut when images are created or used in stable countries where legal
precedent for photography use has been established. Image use and creation becomes far more
murky and problematic in countries in which law and order is vague or even nonexistent.
Even though images created for no.
(a) The current ratio of a company is 61 and its acid-test ratio .docxAASTHA76
(a) The current ratio of a company is 6:1 and its acid-test ratio is 1:1. If the inventories and prepaid items amount to $445,500, what is the amount of current liabilities?
Current Liabilities
$
89100
(b) A company had an average inventory last year of $113,000 and its inventory turnover was 6. If sales volume and unit cost remain the same this year as last and inventory turnover is 7 this year, what will average inventory have to be during the current year? (Round answer to 0 decimal places, e.g. 125.)
Average Inventory
$
96857
(c) A company has current assets of $88,800 (of which $35,960 is inventory and prepaid items) and current liabilities of $35,960. What is the current ratio? What is the acid-test ratio? If the company borrows $12,970 cash from a bank on a 120-day loan, what will its current ratio be? What will the acid-test ratio be? (Round answers to 2 decimal places, e.g. 2.50.)
Current Ratio
2.47
:1
Acid Test Ratio
:1
New Current Ratio
:1
New Acid Test Ratio
:1
(d) A company has current assets of $586,700 and current liabilities of $200,100. The board of directors declares a cash dividend of $173,700. What is the current ratio after the declaration but before payment? What is the current ratio after the payment of the dividend? (Round answers to 2 decimal places, e.g. 2.50.)
Current ratio after the declaration but before payment
:1
Current ratio after the payment of the dividend
:1
The following data is given:
December 31,
2015
2014
Cash
$66,000
$52,000
Accounts receivable (net)
90,000
60,000
Inventories
90,000
105,000
Plant assets (net)
380,500
320,000
Accounts payable
54,500
41,500
Salaries and wages payable
11,500
5,000
Bonds payable
70,500
70,000
8% Preferred stock, $40 par
100,000
100,000
Common stock, $10 par
120,000
90,000
Paid-in capital in excess of par
80,000
70,000
Retained earnings
190,000
160,500
Net credit sales
930,000
Cost of goods sold
735,000
Net income
81,000
Compute the following ratios: (Round answers to 2 decimal places e.g. 15.25.)
(a)
Acid-test ratio at 12/31/15
: 1
(b)
Accounts receivable turnover in 2015
times
(c)
Inventory turnover in 2015
times
(d)
Profit margin on sales in 2015
%
(e)
Return on common stock equity in 2015
%
(f)
Book value per share of common stock at 12/31/15
$
Exercise 24-4
As loan analyst for Utrillo Bank, you have been presented the following information.
Toulouse Co.
Lautrec Co.
Assets
Cash
$113,900
$311,200
Receivables
227,200
302,700
Inventories
571,200
510,700
Total current assets
912,300
1,124,600
Other assets
506,000
619,800
Total assets
$1,418,300
$1,744,400
Liabilities and Stockholders’ Equity
Current liabilities
$291,300
$350,400
Long-term liabilities
390,800
506,000
Capital stock and retained earnings
736,200
888,000
Total liabilities and stockholders’ equity
$1.
(1) How does quantum cryptography eliminate the problem of eaves.docxAASTHA76
Quantum cryptography eliminates eavesdropping by using the principles of quantum mechanics, where any interception of encrypted information can be detected. However, quantum cryptography has limitations in the distance over which it can be effectively implemented and requires specialized equipment. Developments in both theoretical and applied cryptography will be influenced by advances in computing power, communication technologies, user needs for security and privacy, and socioeconomic or geopolitical factors.
#transformation
10
Event
Trends
for 2019
10 Event Trends for 2019
C O P Y R I G H T
All rights reserved. No part of this report may be
reproduced or transmitted in any form or by any
means whatsoever (including presentations, short
summaries, blog posts, printed magazines, use
of images in social media posts) without express
written permission from the author, except in the
case of brief quotations (50 words maximum and
for a maximum of 2 quotations) embodied in critical
articles and reviews, and with clear reference to
the original source, including a link to the original
source at https://www.eventmanagerblog.com/10-
event-trends/. Please refer all pertinent questions
to the publisher.
page 2
https://www.eventmanagerblog.com/10-event-trends/
https://www.eventmanagerblog.com/10-event-trends/
10 Event Trends for 2019
CONTENTS
INTRODUCTION page 5
TRANSFORMATION 8
10. PASSIVE ENGAGEMENT 10
9. CONTENT DESIGN 13
8. SEATING MATTERS 16
7. JOMO - THE JOY OF MISSING OUT 19
6. BETTER SAFE THAN SORRY 21
5. CAT SPONSORSHIP 23
4. SLOW TICKETING 25
3. READY TO BLOCKCHAIN 27
2. MARKETING BUDGETS SHIFTING MORE TO EVENTS 28
1. MORE THAN PLANNERS 30
ABOUT THE AUTHOR 31
CMP CREDITS 32
CREDITS AND THANKS 32
DISCLAIMER 32
page 3
INTERACTIVITY
AT THE HEART OF YOUR MEETINGS
Liven up your presentations!
EVENIUM
ConnexMe
San Francisco/Paris [email protected]
AD
https://eventmb.com/2PvIw1f
10 Event Trends for 2019
I am very glad to welcome you to the 8th edition of our annual
event trends. This is going to be a different one.
One element that made our event trends stand out from
the thousands of reports and articles on the topic is that we
don’t care about pleasing companies, pundits, suppliers, star
planners and the likes. Our only focus is you, the reader, to
help you navigate through very uncertain times.
This is why I decided to bring back this report, by far the most
popular in the industry, to its roots. 10 trends that will actually
materialize between now and November 2019, when we will
publish edition number nine.
I feel you have a lot going on, with your events I mean.
F&B, room blocks, sponsorship, marketing security, technology.
I think I failed you in previous editions. I think I gave you too
much. This report will be the most concise and strategic piece
of content you will need for next year.
If you don’t read anything else this year, it’s fine. As long as you
read the next few words.
INTRODUCTION
INTRODUCTION -
Julius Solaris
EventMB Editor
page 5
https://www.eventmanagerblog.com
10 Event Trends for 2019
How did I come up with these trends?
~ As part of this report, we reviewed 350 events. Some of the most successful
worldwide.
~ Last year we started a community with a year-long trend watch. That helped
us to constantly research new things happening in the industry.
~ We have reviewed north of 300 event technology solutions for our repor.
$10 now and $10 when complete Use resources from the required .docxAASTHA76
$10 now and $10 when complete
Use resources from the required readings or the GCU Library to create a 10‐15 slide digital presentation to be shown to your colleagues informing them of specific cultural norms and sociocultural influences affecting student learning at your school.
Choose a culture to research. State the country or countries of origin of your chosen culture and your reason for selecting it.
Include sociocultural influences on learning such as:
Religion
Dress
Cultural Norms
Food
Socialization
Gender Differences
Home Discipline
Education
Native Language
Include presenter’s notes, a title slide, in‐text citations, and a reference slide that contains three to five sources from the required readings or the GCU Library.
.
#include <string.h>
#include <stdlib.h>
#include <sys/types.h>
#include <sys/wait.h>
#include <stdio.h>
#include <unistd.h>
#include <string.h>
// Function: void parse(char *line, char **argv)
// Purpose : This function takes in a null terminated string pointed to by
// <line>. It also takes in an array of pointers to char <argv>.
// When the function returns, the string pointed to by the
// pointer <line> has ALL of its whitespace characters (space,
// tab, and newline) turned into null characters ('\0'). The
// array of pointers to chars will be modified so that the zeroth
// slot will point to the first non-null character in the string
// pointed to by <line>, the oneth slot will point to the second
// non-null character in the string pointed to by <line>, and so
// on. In other words, each subsequent pointer in argv will point
// to each subsequent "token" (characters separated by white space)
// IN the block of memory stored at the pointer <line>. Since all
// the white space is replaced by '\0', every one of these "tokens"
// pointed to by subsequent entires of argv will be a valid string
// The "last" entry in the argv array will be set to NULL. This
// will mark the end of the tokens in the string.
//
void parse(char *line, char **argv)
{
// We will assume that the input string is NULL terminated. If it
// is not, this code WILL break. The rewriting of whitespace characters
// and the updating of pointers in argv are interleaved. Basically
// we do a while loop that will go until we run out of characters in
// the string (the outer while loop that goes until '\0'). Inside
// that loop, we interleave between rewriting white space (space, tab,
// and newline) with nulls ('\0') AND just skipping over non-whitespace.
// Note that whenever we encounter a non-whitespace character, we record
// that address in the array of address at argv and increment it. When
// we run out of tokens in the string, we make the last entry in the array
// at argv NULL. This marks the end of pointers to tokens. Easy, right?
while (*line != '\0') // outer loop. keep going until the whole string is read
{ // keep moving forward the pointer into the input string until
// we encounter a non-whitespace character. While we're at it,
// turn all those whitespace characters we're seeing into null chars.
while (*line == ' ' || *line == '\t' || *line == '\n' || *line == '\r')
{ *line = '\0';
line++;
}
// If I got this far, I MUST be looking at a non-whitespace character,
// or, the beginning of a token. So, let's record the address of this
// beginning of token to the address I'm pointing at now. (Put it in *argv)
.
$ stated in thousands)Net Assets, Controlling Interest.docxAASTHA76
$ stated in thousands)
Net Assets, Controlling Interest
–
–
Net Assets, Noncontrolling Interest
AUDIT COMMITTEE
of the
Executive Board of the Boy Scouts of America
Francis R. McAllister, Chairman
David Biegler Ronald K. Migita
Dennis H. Chookaszian David Moody
Report of Independent Auditors
To the Executive Board of the National Council of the Boy Scouts of America
We have audited the accompanying consolidated financial statements of the National Council of the Boy Scouts
of America and its affiliates (the National Council), which comprise the consolidated statement of financial position
as of December 31, 2016, and the related consolidated statements of revenues, expenses, and other changes in net
assets, of functional expenses and of cash flows for the year then ended.
Management’s Responsibility for the Consolidated Financial Statements
Management is responsible for the preparation and fair presentation of the consolidated financial statements
in accordance with accounting principles generally accepted in the United States of America; this includes the
design, implementation and maintenance of internal control relevant to the preparation and fair presentation of
consolidated financial statements that are free from material misstatement, whether due to fraud or error.
Auditors’ Responsibility
Our responsibility is to express an opinion on the consolidated financial statements based on our audit. We
conducted our audit in accordance with auditing standards generally accepted in the United States of America.
Those standards require that we plan and perform the audit to obtain reasonable assurance about whether the
consolidated financial statements are free from material misstatement.
An audit involves performing procedures to obtain audit evidence about the amounts and disclosures in the
consolidated financial statements. The procedures selected depend on our judgment, including the assessment of
the risks of material misstatement of the consolidated financial statements, whether due to fraud or error. In making
those risk assessments, we consider internal control relevant to the National Council’s preparation and fair
presentation of the consolidated financial statements in order to design audit procedures that are appropriate in the
circumstances, but not for the purpose of expressing an opinion on the effectiveness of the National Council’s
internal control. Accordingly, we express no such opinion. An audit also includes evaluating the appropriateness of
accounting policies used and the reasonableness of significant accounting estimates made by management, as well as
evaluating the overall presentation of the consolidated financial sta.
#include <stdio.h>
#include <stdlib.h>
#include <pthread.h>
#include <time.h>
#include <unistd.h>
// Change the constant below to change the number of philosophers
// coming to lunch...
// This is a known GOOD solution based on the Arbitrator
// solution
#define PHILOSOPHER_COUNT 20
// Each philosopher is represented by one thread. Each thread independenly
// runs the same "think/start eating/finish eating" program.
pthread_t philosopher[PHILOSOPHER_COUNT];
// Each chopstick gets one mutex. If there are N philosophers, there are
// N chopsticks. That's the whole problem. There's not enough chopsticks
// for all of them to be eating at the same time. If they all cooperate,
// everyone can eat. If they don't... or don't know how.... well....
// philosophers are going to starve.
pthread_mutex_t chopstick[PHILOSOPHER_COUNT];
// The arbitrator solution adds a "waiter" that ensures that only pairs of
// chopsticks are grabbed. Here is the mutex for the waiter ;)
pthread_mutex_t waiter;
void *philosopher_program(int philosopher_number)
{ // In this version of the "philosopher program", the philosopher
// will think and eat forever.
while (1)
{ // Philosophers always think before they eat. They need to
// build up a bit of hunger....
//printf ("Philosopher %d is thinking\n", philosopher_number);
usleep(1);
// That was a lot of thinking.... now hungry... this
// philosopher (who knows his own number) grabs the chopsticks
// to her/his right and left. The chopstick to the left of
// philosopher N is chopstick N. The chopstick to the right
// of philosopher N is chopstick N+1
//printf ("Philosopher %d wants chopsticks\n",philosopher_number);
pthread_mutex_lock(&waiter);
pthread_mutex_lock(&chopstick[philosopher_number]);
pthread_mutex_lock(&chopstick[(philosopher_number+1)%PHILOSOPHER_COUNT]);
pthread_mutex_unlock(&waiter);
// Hurray, if I got this far I'm eating
printf ("Philosopher %d is eating\n",philosopher_number);
//usleep(1); // I spend twice as much time eating as thinking...
// typical....
// I'm done eating. Now put the chopsticks back on the table
//printf ("Philosopher %d finished eating\n",philosopher_number);
pthread_mutex_unlock(&chopstick[philosopher_number]);
pthread_mutex_unlock(&chopstick[(philosopher_number+1)%PHILOSOPHER_COUNT]);
//printf("Philosopher %d has placed chopsticks on the table\n", philosopher_number);
}
return(NULL);
}
int main()
{ int i;
srand(time(NULL));
for(i=0;i<PHILOSOPHER_COUNT;i++)
pthread_mutex_init(&chopstick[i],NULL);
pthread_mutex_init(&waiter,NULL);
for(i=0;i<PH.
#Assessment BriefDiploma of Business Eco.docxAASTHA76
#
Assessment BriefDiploma of Business Economics for Business
Credit points : 6 Prerequisites : None Co-requisites :
Subject Coordinator : Harriet Scott
Deadline : Sunday at the end of week 10 (Turnitin via CANVAS submission). Reflection due week 11 in tutorials.
ASSESSMENT TASK #3: FINAL CASE STUDY REPORT 25%
TASK DESCRIPTION
This assessment is a formal business report on a case study. Case studies will be assigned to students in the Academic and Business Communication subject. Readings on the case study are available on Canvas, in the Economics for Business subject. Students will also write a reflection on learning in tutorial classes in week 11.
LEARNING OUTCOMES
· Demonstrates understanding of microeconomic and macroeconomic concepts
· Applies economic concepts to contemporary issues and events
· Evaluates possible solutions for contemporary economic and business problems
· Communicates economic information in a business report format
INSEARCH CRICOS provider code: 00859D I UTS CRICOS provider code: 00099F INSEARCH Limited is a controlled entity of the University of Technology, Sydney (UTS), a registered non-self accrediting higher education institution and a pathway provider to UTS.
1. Refer to the case study you are working on for your presentation in Academic and Business Communication. Read the news stories for your case study, found on Canvas.
2. Individually, write a business report that includes the following information:
· Description of the main issue/problem and causes
· Description of the impact on stakeholders
· Analysis of economic concepts relevant to the case study (3-5 concepts)
· Recommendations for alternate solutions to the issue/problem
3. In your week 11 tutorial, write your responses to the reflection questions provided by your tutor, describing your learning experience in this assessment.
Other Requirements Format: Business Report
· Use the Business Report format as taught in BABC001 (refer to CANVAS Help for more information)
· Write TEEL paragraphs (refer to CANVAS Help for more information)
· All work submitted must be written in your own words, using paraphrasing techniques taught in BABC001
· Check Canvas — BECO — Assessments — Final Report page and ‘Writing a report' flyer for more information
Report Presentation: You need to include:
· Cover page as taught in BABC001
· Table of contents - list headings, subheadings and page numbers
· Reference list - all paraphrased/summarised/quoted evidence should include citations; all citations should be detailed in the Reference List
Please ensure your assignment is presented professionally. Suggested structure:
· Cover page
· Table of contents (bold, font size 18)
· Executive summary (bold, font size 18)
· 1.0 Introduction (bold, font size 16)
· 2.0 Main issue (bold, font size 16)
o 2.1 Causes (italics, font size 14)
· 3.0 Stakeholders (bold, font size 16)
o 3.1 Stakeholder 1 (italics, font size 14) o 3.2 Stakeholder 2 (italics, font size 14) o 3.3 Stakeholde.
#include <stdio.h>
#include <stdint.h>
#include <stdbool.h>
// Prototype of FOUR functions, each for a STATE.
// The func in State 1 performs addition of "unsigned numbers" x0 and x1.
int s1_add_uintN(int x0, int x1, bool *c_flg);
// The func in State 2 performs addition of "signed numbers" x0 and x1.
int s2_add_intN(int x0, int x1, bool *v_flg);
// The func in State 3 performs subtraction of "unsigned numbers" x0 and x1.
int s3_sub_uintN(int x0, int x1, bool *c_flg);
// The func in State 3 performs subtraction of "signed numbers" x0 and x1.
int s4_sub_intN(int x0, int x1, bool *v_flg);
// We define the number of bits and the related limits of unsigned and
// and signed numbers.
#define N 5 // number of bits
#define MIN_U 0 // minimum value of unsigned N-bit number
#define MAX_U ((1 << N) - 1) // maximum value of unsigned N-bit number
#define MIN_I (-(1 << (N-1)) ) // minimum value of signed N-bit number
#define MAX_I ((1 << (N-1)) - 1) // maximum value of signed N-bit number
// We use the following three pointers to access data, which can be changed
// when the program pauses. We need to make sure to have the RAM set up
// for these addresses.
int *pIn = (int *)0x20010000U; // the value of In should be -1, 0, or 1.
int *pX0 = (int *)0x20010004U; // X0 and X1 should be N-bit integers.
int *pX1 = (int *)0x20010008U;
int main(void) {
enum progState{State1 = 1, State2, State3, State4};
enum progState cState = State1; // Current State
bool dataReady = false;
bool cFlg, vFlg;
int result;
while (1) {
dataReady = false;
// Check if the data are legitimate
while (!dataReady) {
printf("Halt program here to provide correct update of data\n");
printf("In should be -1, 0, and 1 and ");
printf("X0 and X1 should be N-bit SIGNED integers\n");
if (((-1 <= *pIn) && (*pIn <= 1)) &&
((MIN_I <= *pX0) && (*pX0 <= MAX_I)) &&
((MIN_I <= *pX1) && (*pX1 <= MAX_I))) {
dataReady = true;
}
}
printf("Your input: In = %d, X0 = %d, X1 = %d \n", *pIn, *pX0, *pX1);
switch (cState) {
case State1:
result = s1_add_uintN(*pX0, *pX1, &cFlg);
printf("State = %d, rslt = %d, Cflg = %d\n", cState, result, cFlg);
cState += *pIn;
if (cState < State1) cState += State4;
break;
case State2:
result = s2_add_intN(*pX0, *pX1, &vFlg);
printf("State = %d, rslt = %d, Vflg = %d\n", cState, result, vFlg);
cState += *pIn;
break;
case State3:
case State4:
default:
printf("Error with the program state\n");
}
}
}
int s1_add_uintN(int x0, int x1, bool *c_flg) {
if (x0 < 0) x0 = x0 + MAX_U + 1;
if.
ISO/IEC 27001, ISO/IEC 42001, and GDPR: Best Practices for Implementation and...PECB
Denis is a dynamic and results-driven Chief Information Officer (CIO) with a distinguished career spanning information systems analysis and technical project management. With a proven track record of spearheading the design and delivery of cutting-edge Information Management solutions, he has consistently elevated business operations, streamlined reporting functions, and maximized process efficiency.
Certified as an ISO/IEC 27001: Information Security Management Systems (ISMS) Lead Implementer, Data Protection Officer, and Cyber Risks Analyst, Denis brings a heightened focus on data security, privacy, and cyber resilience to every endeavor.
His expertise extends across a diverse spectrum of reporting, database, and web development applications, underpinned by an exceptional grasp of data storage and virtualization technologies. His proficiency in application testing, database administration, and data cleansing ensures seamless execution of complex projects.
What sets Denis apart is his comprehensive understanding of Business and Systems Analysis technologies, honed through involvement in all phases of the Software Development Lifecycle (SDLC). From meticulous requirements gathering to precise analysis, innovative design, rigorous development, thorough testing, and successful implementation, he has consistently delivered exceptional results.
Throughout his career, he has taken on multifaceted roles, from leading technical project management teams to owning solutions that drive operational excellence. His conscientious and proactive approach is unwavering, whether he is working independently or collaboratively within a team. His ability to connect with colleagues on a personal level underscores his commitment to fostering a harmonious and productive workplace environment.
Date: May 29, 2024
Tags: Information Security, ISO/IEC 27001, ISO/IEC 42001, Artificial Intelligence, GDPR
-------------------------------------------------------------------------------
Find out more about ISO training and certification services
Training: ISO/IEC 27001 Information Security Management System - EN | PECB
ISO/IEC 42001 Artificial Intelligence Management System - EN | PECB
General Data Protection Regulation (GDPR) - Training Courses - EN | PECB
Webinars: https://pecb.com/webinars
Article: https://pecb.com/article
-------------------------------------------------------------------------------
For more information about PECB:
Website: https://pecb.com/
LinkedIn: https://www.linkedin.com/company/pecb/
Facebook: https://www.facebook.com/PECBInternational/
Slideshare: http://www.slideshare.net/PECBCERTIFICATION
Beyond Degrees - Empowering the Workforce in the Context of Skills-First.pptxEduSkills OECD
Iván Bornacelly, Policy Analyst at the OECD Centre for Skills, OECD, presents at the webinar 'Tackling job market gaps with a skills-first approach' on 12 June 2024
Chapter wise All Notes of First year Basic Civil Engineering.pptxDenish Jangid
Chapter wise All Notes of First year Basic Civil Engineering
Syllabus
Chapter-1
Introduction to objective, scope and outcome the subject
Chapter 2
Introduction: Scope and Specialization of Civil Engineering, Role of civil Engineer in Society, Impact of infrastructural development on economy of country.
Chapter 3
Surveying: Object Principles & Types of Surveying; Site Plans, Plans & Maps; Scales & Unit of different Measurements.
Linear Measurements: Instruments used. Linear Measurement by Tape, Ranging out Survey Lines and overcoming Obstructions; Measurements on sloping ground; Tape corrections, conventional symbols. Angular Measurements: Instruments used; Introduction to Compass Surveying, Bearings and Longitude & Latitude of a Line, Introduction to total station.
Levelling: Instrument used Object of levelling, Methods of levelling in brief, and Contour maps.
Chapter 4
Buildings: Selection of site for Buildings, Layout of Building Plan, Types of buildings, Plinth area, carpet area, floor space index, Introduction to building byelaws, concept of sun light & ventilation. Components of Buildings & their functions, Basic concept of R.C.C., Introduction to types of foundation
Chapter 5
Transportation: Introduction to Transportation Engineering; Traffic and Road Safety: Types and Characteristics of Various Modes of Transportation; Various Road Traffic Signs, Causes of Accidents and Road Safety Measures.
Chapter 6
Environmental Engineering: Environmental Pollution, Environmental Acts and Regulations, Functional Concepts of Ecology, Basics of Species, Biodiversity, Ecosystem, Hydrological Cycle; Chemical Cycles: Carbon, Nitrogen & Phosphorus; Energy Flow in Ecosystems.
Water Pollution: Water Quality standards, Introduction to Treatment & Disposal of Waste Water. Reuse and Saving of Water, Rain Water Harvesting. Solid Waste Management: Classification of Solid Waste, Collection, Transportation and Disposal of Solid. Recycling of Solid Waste: Energy Recovery, Sanitary Landfill, On-Site Sanitation. Air & Noise Pollution: Primary and Secondary air pollutants, Harmful effects of Air Pollution, Control of Air Pollution. . Noise Pollution Harmful Effects of noise pollution, control of noise pollution, Global warming & Climate Change, Ozone depletion, Greenhouse effect
Text Books:
1. Palancharmy, Basic Civil Engineering, McGraw Hill publishers.
2. Satheesh Gopi, Basic Civil Engineering, Pearson Publishers.
3. Ketki Rangwala Dalal, Essentials of Civil Engineering, Charotar Publishing House.
4. BCP, Surveying volume 1
Strategies for Effective Upskilling is a presentation by Chinwendu Peace in a Your Skill Boost Masterclass organisation by the Excellence Foundation for South Sudan on 08th and 09th June 2024 from 1 PM to 3 PM on each day.
Walmart Business+ and Spark Good for Nonprofits.pdfTechSoup
"Learn about all the ways Walmart supports nonprofit organizations.
You will hear from Liz Willett, the Head of Nonprofits, and hear about what Walmart is doing to help nonprofits, including Walmart Business and Spark Good. Walmart Business+ is a new offer for nonprofits that offers discounts and also streamlines nonprofits order and expense tracking, saving time and money.
The webinar may also give some examples on how nonprofits can best leverage Walmart Business+.
The event will cover the following::
Walmart Business + (https://business.walmart.com/plus) is a new shopping experience for nonprofits, schools, and local business customers that connects an exclusive online shopping experience to stores. Benefits include free delivery and shipping, a 'Spend Analytics” feature, special discounts, deals and tax-exempt shopping.
Special TechSoup offer for a free 180 days membership, and up to $150 in discounts on eligible orders.
Spark Good (walmart.com/sparkgood) is a charitable platform that enables nonprofits to receive donations directly from customers and associates.
Answers about how you can do more with Walmart!"
Temple of Asclepius in Thrace. Excavation resultsKrassimira Luka
The temple and the sanctuary around were dedicated to Asklepios Zmidrenus. This name has been known since 1875 when an inscription dedicated to him was discovered in Rome. The inscription is dated in 227 AD and was left by soldiers originating from the city of Philippopolis (modern Plovdiv).
it describes the bony anatomy including the femoral head , acetabulum, labrum . also discusses the capsule , ligaments . muscle that act on the hip joint and the range of motion are outlined. factors affecting hip joint stability and weight transmission through the joint are summarized.
Leveraging Generative AI to Drive Nonprofit InnovationTechSoup
In this webinar, participants learned how to utilize Generative AI to streamline operations and elevate member engagement. Amazon Web Service experts provided a customer specific use cases and dived into low/no-code tools that are quick and easy to deploy through Amazon Web Service (AWS.)
हिंदी वर्णमाला पीपीटी, hindi alphabet PPT presentation, hindi varnamala PPT, Hindi Varnamala pdf, हिंदी स्वर, हिंदी व्यंजन, sikhiye hindi varnmala, dr. mulla adam ali, hindi language and literature, hindi alphabet with drawing, hindi alphabet pdf, hindi varnamala for childrens, hindi language, hindi varnamala practice for kids, https://www.drmullaadamali.com
Discussion 41- AL JOHARA In 1994 the European Channel Tun.docx
1. Discussion 4
1- AL JOHARA
In 1994 the European Channel Tunnel was opened, and it linked
the European continent and Britain. It is a 31-mile tunnel
carrying freight trains and Eurostar trains between Paris and
London and is today considered the fast and modern transport
institution. Although the tunnel traces its background to the
19th century, it is considered an achievement of the 20th
century (Syon, 2008).
Though the project has been credited to be a success, the size of
the channel had intrinsic uncertainties and risks. Tunneling
projects are naturally high risk and often end up in high overrun
on budget and completion dates due to the underground setting
that were not anticipated during the contract (Syon, 2008). The
risks present in the Chunnel project were design and
construction challenges brought about by the changing
geological situations, the third-party issues, the safety of the
workers, infrastructure/property damage and environmental risk
(Berend, 2016). In Britain there was no space for disposing of
spoil and emission of waste became a significant challenge.
Though there was a mitigation of disposing spoil in the Coast,
some critiques were of the view that it would destroy the
environment. The risk of the tunnel collapsing due to
earthquakes was a concern to many individuals; however, the
tunnels had a design which ensured they were resistant and
caution was taken to reduce possibility of damage to equipment
installed in them and to make sure entrances couldn’t be
blocked by local collapses and landslips (Pireddu, 2017).
Technological risks were experienced in the construction of the
tunnel. These include the political and economical viability of
the machinery that were required to ensure the project goals
were achieved. In the Chunnel tunnel, this risk was mainly
2. assumed by the contractor, Eurotunnel. All the technological
risks involved were mitigated by the comprehensive geological
research of the strata of where the tunnel was to be constructed
(Berend, 2016). Earlier concerns demanded the state of the art
equipment which were costly and afterward found unnecessary.
The political risks were mitigated by assigning the task to a
private investor after the conservative and left-wing reign in
Britain (Pireddu, 2017).
The project further experienced credit risk. The risk calculated
on the basis of the investor’s creditworthiness. Unlike other
mega-projects which are normally funded by the government,
the Channel tunnel was private-funded and therefore presented a
high risk to the contractors and investors. Most private
investors were giving a small fraction of the total approximation
cost. The administration for example under credit limitation had
to suggest lump-sum contracts, which were impractical for such
projects. Litigation and claims at the end of the project were
experienced (Berend, 2016).
2- Fahad ALMahmoud
One of the risks that the English tunnel faced is aerodynamic of
the tunnel, the designers have found that the temperature in the
middle of the tunnel is going to reach a very high degree since
the heat is going to be generated from the high speed of the
trains as they go through the long tunnel and air circulation
won’t be available in our case. The engineers have decided to
install a cooling system inside the tunnel, the system includes
pipes along the tunnel where chilled water can circulate freely
from refrigeration units designed at both ends of the tunnel.
The second risk of the construction of the tunnel is the safety if
the tunnel catches fire of a natural disaster. In 1996, a fire
incident caught a train was heading toward France which caused
3. huge destruction to the tunnel and the repairment took a long
time to be done. After this incident, the designers create a Fire
Equipment Management Centers (FEMC) and a traction system
which divides every 1,500 meters into sections that can be
isolated when a certain disaster occurs, so the damage and
destruction can be stopped and limited.
Discussion 6
1- naif al ghuthami
(a) Develop a set of operational requirements for a simple lawn
tractor. Limit
yourself to no more than 15 operational requirements.
Operational requirements for a simple lawn tractor are:
1. E ffective knife stroke
2. Effective cutting height
3. Sufficient working width
4. Knife speed
5. Knife forward speed
6. Crank speed
7. Ratio of speed
8. Sufficient filed capability
9. Filed efficiency
10. Sufficient harvest capability
11. Economic fuel consumption
12. Effective in all weather
13. Rotating blades
14. Lights to work in the dark
(b) Develop a set of performance requirements for the same
4. lawn tractor.
Limit yourself to no more than 30 performance requirements.
Performance requirements for a simple lawn tractor are:
1. H igh quality knife to cute efficiently
2. Capacity to move knife to change cutting depth
3. Rotation of blades to maximize efficiency
4. Setting of speed to make it high/low
5. Effective materials to sustain quality of parts
6. Cost-effective fuel usage system
7. Cover all running parts to prevent damage
8. Effective light system to perform in the shaded areas
9. Light-weight to move is easily
10. Easy and safe to use in all weather
11. Knife need to be stop in minimum time
12. Guards on the blades
13. Proper lubrication of the running parts
14. Efficient ignition for start it
15. Distance meter to cut grass with required length
16. Gear system to manage its speed
17. Sufficient blade control system
18. High quality color and finishing
19. Sufficient sitting capacity
20. Easy to operate and signal
21. Overall high efficiency in all operations
(d) How would you go about validating the requirements in (b)?
To validate the requirements, I make comparison between
operational requirements and performance requirements. I
analyze its operations and performance to make it time-effective
and cost-effective.
2- Khalid al assaf
5. - Develop a set of operational requirements for a simple lawn
tractor. Limit yourself to no more than 15 operational
requirements.
Ø Blades to function when gear changer is used
Ø Should be simple and easy to operate.
Ø Should have a 4wheel drive.
Ø Should shave grass to the minimum level possible
Ø Should cover a wide area of about 30 inches when cutting
Ø The driver should be covered from rain.
Ø The feet should be protected from rotating blades
Ø Blade to only operate when driver releases the command.
· The driver should be able to sit
- Develop a set of performance requirements for the same lawn
tractor. Limit yourself to no more than 30 performance
requirements.
Ø Should have numerous blades
Ø The rotating horse power should be high
Ø Cutting blades to rotate at speed
Ø Tractor should have a balanced weight.
Ø Should be well painted with a long lasting paint
Ø Should operate safely and always reliable.
Ø Blades not to run for long after stop command.
Ø Should pass all the tests on functionality.
Ø Have parts properly greased.
Ø Have steering wheel for navigation.
Ø Be able to take a tight bend.
Ø Have a sound silencer to minimize noise pollution.
Ø Should have shock absorbers to minimize vibration.
Ø To have a weather roof for the driver.
Ø Have lighting system.
Ø Moderate fuel consumption.
Ø Accessible re-fuel tank.
Ø Have rechargeable battery for ignition.
6. Ø Spear wheel
Ø Toolbox for minor repairs.
- How would you go about validating the requirements in (b)?
Ø I will carry out analysis to ascertain that performance
requirements are meeting the operational requirements as set by
the users.
Discussion 7
1- aljohara
8.4Under the subsection Program Risks, five examples are listed
of conditions that may result in a significant probability of
program failure. For each example, explain briefly what
consequences of the condition may lead to a program failure.
· A leading-edge unproven technology is to be
applied: Implementing unproven new technology may lead to
program failure because there is not enough information on this
technology. Therefore, it is impossible to identify some of the
issues that might arise and impossible to predict the outcome of
the new technology. Also, new technologies cost a lot of money,
and it is expensive to maintain. These technologies require very
skilled and knowledgeable engineers to work on the
7. implementation process and direct and guide the people who are
going to use it.
· A major increase in performance is required: An increase in
performance may result in program failure because the system
might not handle the required increase and the increase is
beyond its capabilities. This could result in slowing down the
system and possibly a complete shutdown of the entire system.
Also, increasing the performance require additional costs that
might not be available.
· A major decrease in cost is required for the same
performance: A decrease in cost may lead to program failure
because it will affect the quality of the product or service
performed. The decrease in cost can be in the form of cutting
down on the number of employees, using cheaper technologies,
and reducing maintenance. Reducing the cost and maintaining
the same level of performance is a big challenge in any project
that can lead to failure.
· A significantly more severe operating environment is
postulated: Operating in a severe environment may lead to
program failure because the program is not intended to operate
in this environment. The program will break down fast and will
require additional cost to repair. Also, the program will need to
be maintained more frequently.
· An unduly short development schedule is imposed: Imposing a
short development schedule may lead to program failure
because it will affect the overall prosses of development. The
developer will have to cut the time from testing or evaluation
which in the end might affect the quality of the final product.
2- Fahad almahmoud
1. Poorly defined program scope- Project/program scope is an
essential part of project planning that involves identifying and
documenting the project goals, deliverables, costs, activities
and the due date for delivery of the project. Scope section in
project planning also includes guidelines for making decisions
8. for any change requests that arise during the course of the
project. If the program scope is not properly defined i.e.,
without specific goals and deliverables, then it would eventually
lead to program failures. In large projects, there are
possibilities of ‘scope creep’. Scope creep is a situation in
which part or the whole project requires additional work, time
and efforts due to poor planning or miscommunication. If all
these factors are not documented properly in the project’s
scope, then it leads to project failure.
2. Failure to identify key assumptions- The assumptions and
constraints are factors that needs to be identified correctly and
documented in the entire project life cycle. These factors play a
vital role in the planning phase. The risk management is heavily
reliant on the assumptions. Hence, if they are not analyzed
properly, it might lead to project failures affecting project’s
outcome.
3. Inadequate risk management- Poor or inadequate risk
management is one of the major causes for project failures.
Ignoring or not identifying any possible risks in the project life
cycle might lead to huge loss in terms of cost, time and assets.
It spoils the reputation of the company and also strains the
relationship between the company and its clients. Accurate
intelligence is required to identify the potential threats and
challenges facing the project. If this is not done properly, then
it may lead to program failure.
4. No use of formal processes and strategies- There is a strong
link between the project and the organization’s key processes
and strategic practices. There are procedures and processes
followed by organizations that are successful for them.
However, if projects do not use these defined processes and
strategic practices, then it might lead to project failure. It is
pertinent that the project managers follow the formal processes
and strategies in the project life cycle to ensure adherence and
compliance with the company policies and procedures. Without
these, the project is a failure.
5. Lack of details in program plans- Lack of details or poor
9. planning leads to project failures. The planning phase is the
most important phase in a project as it leads to success if
properly planned. Otherwise it ends in project failure. All the
essential details in planning such as resources, cost, equipment,
time, delivery deadlines, etc need to be planned with precision.
If the plans does not have such details, then the project team
members will not have any focus to drive the project towards
success.
Discussion 8
1- Fahad almahmoud
For this trade study, four different models of sports cars of the
year 2018, the four cars will be evaluated based five criteria’s
are selected with points which are given to each model on the
basis of the criteria’s given below:
1. Price:
30k – 45k US $ = 2 point
25k – 29k US $ = 3 points
20k – 24k US $ = 4 points
15k – 19k US $ = 5 points
1. Mileage:
15,000 – 20,000 MPG = 5 points
21,000 – 25,000 MPG = 4 points
26,000 – 30,000 MPG = 2points
Above 30,000 = 1 points
1. How many seats:
5 seats = 5 points
4 seats = 4 points
3 Seats = 3 points
2 Seats = 1 point
1. performance:
350 - 450 hp. = 5 points
250-350 hp. = 4 points
10. 200 – 240 hp. = 2 points
100 -200 hp. = 1 points
1. Test speed 0-60 mile per hour:
.Less than 5 second= 5 points
Less than 8 seconds= 3 points
Less than 10 seconds= 1 point
Comparison:
Car Models
Ford Mustang GT
Camaro SS
Challenger R/T
Charger R/T
Criteria
Points
Criteria
Points
Criteria
Points
Criteria
Points
Price US $
18,000
5
27,500
3
29,900
3
24,840
4
Mileage
20,000
5
25,000
4
18,000
11. 5
45,000
1
Seating Capacity
4 Seats
4
4 Seats
4
4 Seats
4
5 Seats
5
Performance
460hp
5
455hp
5
375hp
5
370hp
5
Top speed test
4 s
5
4 s
5
5.1
3
5.2
3
Total
24
21
12. 20
18
Based on the study we will go with the Ford Mustang GT.
2- shahad
Perform a trade study on choosing a new car. Identify four
alternatives between three and five criteria and collect the
necessary information required.
For this trade study, four different models of vehicles of year
2019 of four different automobile companies are selected. Then
five criteria’s are selected and points are given to each model
on the basis of the criteria’s given below:
· Price:
Price defines the actual cost of the cars under study.
30k – 35k US $ = 2 point
25k – 29k US $ = 3 points
20k – 24k US $ = 4 points
15k – 19k US $ = 5 points
· Mileage:
Mileage defines the consumption of fuel by the vehicle. How
many miles can a car can travel in one gallon of fuel. Here
combined mileage of the vehicle is taken.
15 – 20 MPG = 1 points
21 – 25 MPG = 3 points
26 – 30 MPG = 4 points
Above 30 = 5 points
· Seating Capacity:
It means how many seats are available in the vehicle for the
people.
2 Seats = 1 point
5 Seats = 3 points
More than 5 seats = 5 points
13. · Horse Powers:
Horse power defines how powerful the engine of the vehicle is.
140 – 190 hp. = 3 points
200 – 240 hp. = 4 points
More than 240 hp. = 5 points
· Warranty:
Basic numbers of years provided for the warranty.
3 Years = 3 points
4 Years = 4 points
5 Years = 5 points
Comparison:
Car Models
Audi A3 Sedan Premium 40 TRSI
Hyundai Sonata SE 2.4 L
Nissan Altima 2.5 S Sedan
Ford Fusion S FWD
Criteria
Points
Criteria
Points
Criteria
Points
Criteria
Points
Price US $
32,500
2
22,500
4
23,900
4
22,840
4
Mileage (Combined)
29
15. 16
19
18
16
Disscussion 9
1- aljohara
As far as preliminary design review is concerned, this operation
mostly involves the acquisition of an agency to certify the
successful completion of the preliminary design. The main
focus of preliminary design is to undertake a though analysis of
systems components, interfaces as well as all the risky areas in
the implementation of the system. In this case, there is a critical
review of the design requirements and specifications. Before
undertaking preliminary design review, organizations need to
embark on the internal reviews to ensure that the requirements
are clear and well addressed for the implementation of a
workable system (Kossiakoff, Sweet, Seymour, & Biemer, 2011)
In preparation for the PDR review, I will do the following:
1. Arrange an internal review with the design team.
2. Assign key persons from the design team to present with me.
16. 3. Understand the design requirements, objectives, and
specifications.
4. Review the process of how the team came up with the final
design.
5. Familiarize myself with design drawings and details.
6. Focus on the most critical and controversial areas.
7. Hold a practice session for questions that might come up
during the PDR.
8. Prepare an agenda for the actual presentation.
2- fahad almamhmoud
The Preliminary Design Review (PDR) is a technical assessment
that establishes the Allocated Baseline of a system to ensure a
system is operationally effective. A PDR is conducted before
the start of detailed design work and is the first opportunity for
the Government to closely observe the Contractor’s hardware
and software design. This review assesses the allocated design
documented in subsystem product specifications for each
configuration item in the system and ensures that each function,
in the Functional Baseline, has been allocated to one or more
system configuration items. The PDR establishes the allocated
baseline (hardware, software, human/support systems) and
underlying architectures to ensure that the system under review
has a reasonable expectation of satisfying the requirements
within the currently allocated budget and schedule.
Completion of the PDR should provide the following:
· An established system allocated baseline
· An updated risk assessment for the Engineering,
Manufacturing, and Development (EMD) Phase,
· An updated Cost Analysis Requirements Description
· An updated program schedule including system and software
critical path drivers,
· An updating report regarding program sustainment
17. development efforts and schedules.
Disscussion 10
1- naif alghuthami
13.7 Define the terms “verification” and “validation.” Describe
the types of tests
that are directed at each, and explain how they meet the
definitions of these
terms.
In simple terms verification in engineering refers to the process
of checking the correctness of elements in a process, program or
system. Verification is derived from the verb verify which
refers to making sure that an element or what it purports to do
is true or correct or even accurate. The verification process
happens or takes place mainly in order to do away with human
errors during engineering processes. There are different tests
that are carried out in the verification process. The tests include
acceptance testing, smoke testing, and interface testing. A look
at the types of tests carried out during the verification process
reveals the tests meet the verification term. For example,
18. interface testing allows the test team and other stakeholders to
verify whether the interface in place allows for the activities
that it is supposed to.
On the other hand, validation refers to the acts of proving the
accuracy of an action or an element. There are four types of
validation that are carried out in engineering. The first type is
the prospective validation which refers to checking whether a
program does what it is supposed to do in reference to its pre-
planned protocols. The second type of validation is the
retrospective validation which refers to the process of using
historical data to establish whether processes are running as
they are supposed to. The third type of validation is the
concurrent validation which involves establishing whether
functions are running as they are supposed to as production and
manufacturing take place.
The fourth type is revalidation which refers to the repeating of a
validation process already carried out. Tests carried out in
validation testing include; unit testing, system testing,
regression testing amongst others. A look at the types of tests
carried out during the validation process reveals the tests meet
the validation term. For example, in system testing, the tests
carried out help in revealing the accuracy of a system in terms
of meeting its objectives.
2- shahad
Define the terms “verification” and “validation.”Describe the
types of tests that are directed at each, and explain how they
meet the definitions of these terms.
Validation can generally be defined as personifying the actions
to reveal the qualities of any product and to conclude its
eagerness for ensuing the processes by comparing it with its
expectations. Verification can generally be defined as “whether
the product meets the specifications mentioned initially or not.
It also justifies whether we are on a right track towards the final
task or not”. There are many differences in validation and
19. verification, one of the difference is: Verification can be done
without executing the product while for the validation we have
to execute the product first. Development phase has different
phases. Verification and validation are executed in every phases
of the lifecycle.
In verification we consider reviews, walk-throughs and the
inspections while in verification we do the testing
phenomenally. There are different tests that are directed at both
verification and validation. They can be tested in different ways
that is more practicable according to the environment. It is more
important to know that it is not compulsory that a product
passes both the tests, there is always a probability that one
product may pass validation process and fail verification
process or vice versa.
Validation is often executed at the completion of the testing
cycle. A person spends a lot of time describing a product,
building it, making sure his software is bug-free, and then do
user acceptance testing, or submit it to a client / users, perhaps
even a Beta discharge. But sometimes we require Beta
testing too. Verification on the contrary can is tested in the
other ways, and are considered the easy ways (They can be
performed through direct testing, random testing, formal testing
or combining all the tests). For instance we are to design a
product that shouldn’t do 100 rpm, then we have to make sure
that it should not complete more revolutions in the same
time. Moreover, suppose we have the stipulations related to the
project than by checking that specifications without
implementing to see whether the conditions are up to the spot or
not, what we have just done is verification.
SYSTEMS ENGINEERING
PRINCIPLES AND
20. PRACTICE
SECOND EDITION
Alexander Kossiakoff
William N. Sweet
Samuel J. Seymour
Steven M. Biemer
A JOHN WILEY & SONS, INC. PUBLICATION
ffirs02.indd iiiffirs02.indd iii 2/8/2011 11:05:45
AM2/8/2011 11:05:45 AM
ffirs04.indd viffirs04.indd vi 2/8/2011 11:05:47
AM2/8/2011 11:05:47 AM
SYSTEMS
ENGINEERING
PRINCIPLES AND
PRACTICE
ffirs.indd iffirs.indd i 2/8/2011 11:05:44 AM2/8/2011
11:05:44 AM
WILEY SERIES IN SYSTEMS ENGINEERING
AND MANAGEMENT
22. retrieval system, or transmitted in any form or
by any means, electronic, mechanical, photocopying, recording,
scanning, or otherwise, except as
permitted under Section 107 or 108 of the 1976 United States
Copyright Act, without either the prior
written permission of the Publisher, or authorization through
payment of the appropriate per-copy fee
to the Copyright Clearance Center, Inc., 222 Rosewood Drive,
Danvers, MA 01923, (978) 750-8400,
fax (978) 750-4470, or on the web at www.copyright.com.
Requests to the Publisher for permission
should be addressed to the Permissions Department, John Wiley
& Sons, Inc., 111 River Street, Hoboken,
NJ 07030, (201) 748-6011, fax (201) 748-6008, or online at
http://www.wiley.com/go/permission.
Limit of Liability/Disclaimer of Warranty: While the publisher
and author have used their best efforts in
preparing this book, they make no representations or warranties
with respect to the accuracy or
completeness of the contents of this book and specifi cally
disclaim any implied warranties of
merchantability or fi tness for a particular purpose. No warranty
may be created or extended by sales
representatives or written sales materials. The advice and
strategies contained herein may not be suitable
for your situation. You should consult with a professional where
appropriate. Neither the publisher nor
author shall be liable for any loss of profi t or any other
commercial damages, including but not limited to
special, incidental, consequential, or other damages.
For general information on our other products and services or
for technical support, please contact our
Customer Care Department within the United States at (800)
762-2974, outside the United States at
23. (317) 572-3993 or fax (317) 572-4002.
Wiley also publishes its books in a variety of electronic
formats. Some content that appears in print may
not be available in electronic formats. For more information
about Wiley products, visit our web site at
www.wiley.com.
Library of Congress Cataloging-in-Publication Data:
Systems engineering : principles and practice/Alexander
Kossiakoff ... [et al.].—2nd ed.
p. cm.—(Wiley series in systems engineering and
management; 67)
Rev. ed. of: Systems engineering: principles and
practices/Alexander
Kossiakoff, William N. Sweet. 2003.
ISBN 978-0-470-40548-2 (hardback)
1. Systems engineering. I. Kossiakoff, Alexander, 1945– II.
Title.
TA168.K68 2010
620.001′171–dc22
2010036856
Printed in the United States of America
oBook ISBN: 9781118001028
ePDF ISBN: 9781118001011
ePub ISBN: 9781118009031
10 9 8 7 6 5 4 3 2 1
ffirs03.indd ivffirs03.indd iv 2/8/2011 11:05:46
AM2/8/2011 11:05:46 AM
24. To Alexander Kossiakoff,
who never took “ no ” for an answer and refused to believe
that anything was
impossible. He was an extraordinary problem solver, instructor,
mentor, and
friend.
Samuel J. Seymour
Steven M. Biemer
ffirs04.indd vffirs04.indd v 2/8/2011 11:05:47 AM2/8/2011
11:05:47 AM
ffirs04.indd viffirs04.indd vi 2/8/2011 11:05:47
AM2/8/2011 11:05:47 AM
LIST OF ILLUSTRATIONS xiii
LIST OF TABLES xvii
PREFACE TO THE SECOND EDITION xix
PREFACE TO THE FIRST EDITION xxiii
PART I FOUNDATIONS OF SYSTEMS ENGINEERING 1
1 SYSTEMS ENGINEERING AND THE WORLD OF
MODERN
25. SYSTEMS 3
1.1 What Is Systems Engineering? 3
1.2 Origins of Systems Engineering 5
1.3 Examples of Systems Requiring Systems Engineering 10
1.4 Systems Engineering as a Profession 12
1.5 Systems Engineer Career Development Model 18
1.6 The Power of Systems Engineering 21
1.7 Summary 23
Problems 25
Further Reading 26
2 SYSTEMS ENGINEERING LANDSCAPE 27
2.1 Systems Engineering Viewpoint 27
2.2 Perspectives of Systems Engineering 32
2.3 Systems Domains 34
2.4 Systems Engineering Fields 35
2.5 Systems Engineerng Approaches 36
2.6 Systems Engineering Activities and Products 37
2.7 Summary 38
Problems 39
26. Further Reading 40
CONTENTS
vii
ftoc.indd viiftoc.indd vii 2/8/2011 11:05:50 AM2/8/2011
11:05:50 AM
viii CONTENTS
3 STRUCTURE OF COMPLEX SYSTEMS 41
3.1 System Building Blocks and Interfaces 41
3.2 Hierarchy of Complex Systems 42
3.3 System Building Blocks 45
3.4 The System Environment 51
3.5 Interfaces and Interactions 58
3.6 Complexity in Modern Systems 60
3.7 Summary 64
Problems 66
Further Reading 67
4 THE SYSTEM DEVELOPMENT PROCESS 69
4.1 Systems Engineering through the System Life Cycle 69
27. 4.2 System Life Cycle 70
4.3 Evolutionary Characteristics of the Development Process 82
4.4 The Systems Engineering Method 87
4.5 Testing throughout System Development 103
4.6 Summary 106
Problems 108
Further Reading 109
5 SYSTEMS ENGINEERING MANAGEMENT 111
5.1 Managing System Development and Risks 111
5.2 WBS 113
5.3 SEMP 117
5.4 Risk Management 120
5.5 Organization of Systems Engineering 128
5.6 Summary 132
Problems 133
Further Reading 134
PART II CONCEPT DEVELOPMENT STAGE 137
6 NEEDS ANALYSIS 139
6.1 Originating a New System 139
28. 6.2 Operations Analysis 146
6.3 Functional Analysis 151
6.4 Feasibility Defi nition 153
ftoc.indd viiiftoc.indd viii 2/8/2011 11:05:50 AM2/8/2011
11:05:50 AM
CONTENTS ix
6.5 Needs Validation 155
6.6 System Operational Requirements 158
6.7 Summary 162
Problems 163
Further Reading 164
7 CONCEPT EXPLORATION 165
7.1 Developing the System Requirements 165
7.2 Operational Requirements Analysis 170
7.3 Performance Requirements Formulation 178
7.4 Implementation of Concept Exploration 185
7.5 Performance Requirements Validation 189
7.6 Summary 191
29. Problems 193
Further Reading 194
8 CONCEPT DEFINITION 197
8.1 Selecting the System Concept 197
8.2 Performance Requirements Analysis 201
8.3 Functional Analysis and Formulation 206
8.4 Functional Allocation 212
8.5 Concept Selection 214
8.6 Concept Validation 217
8.7 System Development Planning 219
8.8 Systems Architecting 222
8.9 System Modeling Languages: Unifi ed Modeling Language
(UML) and Systems Modeling Language (SysML) 228
8.10 Model-Based Systems Engineering (MBSE) 243
8.11 System Functional Specifi cations 246
8.12 Summary 247
Problems 250
Further Reading 252
9 DECISION ANALYSIS AND SUPPORT 255
9.1 Decision Making 256
30. 9.2 Modeling throughout System Development 262
9.3 Modeling for Decisions 263
9.4 Simulation 272
ftoc.indd ixftoc.indd ix 2/8/2011 11:05:50 AM2/8/2011
11:05:50 AM
x CONTENTS
9.5 Trade-Off Analysis 282
9.6 Review of Probability 295
9.7 Evaluation Methods 299
9.8 Summary 308
Problems 311
Further Reading 312
PART III ENGINEERING DEVELOPMENT STAGE 315
10 ADVANCED DEVELOPMENT 317
10.1 Reducing Program Risks 317
10.2 Requirements Analysis 322
10.3 Functional Analysis and Design 327
10.4 Prototype Development as a Risk Mitigation Technique
31. 333
10.5 Development Testing 340
10.6 Risk Reduction 349
10.7 Summary 350
Problems 352
Further Reading 354
11 SOFTWARE SYSTEMS ENGINEERING 355
11.1 Coping with Complexity and Abstraction 356
11.2 Nature of Software Development 360
11.3 Software Development Life Cycle Models 365
11.4 Software Concept Development: Analysis and Design 373
11.5 Software Engineering Development: Coding and Unit Test
385
11.6 Software Integration and Test 393
11.7 Software Engineering Management 396
11.8 Summary 402
Problems 405
Further Reading 406
12 ENGINEERING DESIGN 409
12.1 Implementing the System Building Blocks 409
32. 12.2 Requirements Analysis 414
12.3 Functional Analysis and Design 416
12.4 Component Design 419
12.5 Design Validation 432
ftoc.indd xftoc.indd x 2/8/2011 11:05:50 AM2/8/2011
11:05:50 AM
CONTENTS xi
12.6 CM 436
12.7 Summary 439
Problems 441
Further Reading 442
13 INTEGRATION AND EVALUATION 443
13.1 Integrating, Testing, and Evaluating the Total System 443
13.2 Test Planning and Preparation 450
13.3 System Integration 455
13.4 Developmental System Testing 462
13.5 Operational Test and Evaluation 467
13.6 Summary 475
33. Problems 478
Further Reading 478
PART IV POSTDEVELOPMENT STAGE 481
14 PRODUCTION 483
14.1 Systems Engineering in the Factory 483
14.2 Engineering for Production 485
14.3 Transition from Development to Production 489
14.4 Production Operations 492
14.5 Acquiring a Production Knowledge Base 497
14.6 Summary 500
Problems 502
Further Reading 503
15 OPERATIONS AND SUPPORT 505
15.1 Installing, Maintaining, and Upgrading the System 505
15.2 Installation and Test 507
15.3 In-Service Support 512
15.4 Major System Upgrades: Modernization 516
15.5 Operational Factors in System Development 520
15.6 Summary 522
34. Problems 523
Further Reading 524
INDEX 525
ftoc.indd xiftoc.indd xi 2/8/2011 11:05:50 AM2/8/2011
11:05:50 AM
ftoc.indd xiiftoc.indd xii 2/8/2011 11:05:50 AM2/8/2011
11:05:50 AM
xiii
1.1 Career opportunities and growth 14
1.2a Technical orientation phase diagram 16
1.2b Technical orientation population density distribution
16
1.3a Systems engineering (SE) career elements derived from
quality work
experiences 19
1.3b Components of employer development of systems
engineers 19
1.4 “ T ” model for systems engineer career development
20
2.1a Performance versus cost 29
2.1b Performance/cost versus cost 29
2.2 The ideal missile design from the viewpoint of various
specialists 31
2.3 The dimensions of design, systems engineering, and
35. project planning
and control 32
2.4 Systems engineering domains 34
2.5 Examples of systems engineering fi elds 35
2.6 Examples of systems engineering approaches 36
2.7 Life cycle systems engineering view 37
3.1 Knowledge domains of systems engineer and design
specialist 45
3.2 Context diagram 53
3.3 Context diagram for an automobile 54
3.4 Environments of a passenger airliner 56
3.5 Functional interactions and physical interfaces 59
3.6 Pyramid of system hierarchy 63
4.1 DoD system life cycle model 71
4.2 System life cycle model 72
4.3 Principal stages in system life cycle 75
4.4 Concept development phases of system life cycle 76
4.5 Engineering development phases in system life cycle 78
4.6 Principal participants in a typical aerospace system
development 86
4.7 DoD MIL - STD499B 90
4.8 IEEE - 1220 systems engineering process 90
4.9 EIA - 632 systems engineering process 91
LIST OF ILLUSTRATIONS
fbetw01.indd xiiifbetw01.indd xiii 2/9/2011 6:29:47
PM2/9/2011 6:29:47 PM
xiv LIST OF ILLUSTRATIONS
4.10 ISO - 15288 Systems engineering process 92
4.11 Systems engineering method top - level fl ow diagram
36. 92
4.12 Systems engineering method fl ow diagram 94
4.13 Spiral model of the defense system life cycle 104
5.1 Systems engineering as a part of project management
112
5.2 Place of SEMP in program management plans 118
5.3 Variation of program risk and effort throughout system
development 121
5.4 Example of a risk mitigation waterfall chart 122
5.5 An example of a risk cube display 124
6.1 Needs analysis phase in the system life cycle 140
6.2 Needs analysis phase fl ow diagram 147
6.3 Objectives tree structure 150
6.4 Example objectives tree for an automobile 151
6.5 Analysis pyramid 156
7.1 Concept exploration phase in system life cycle 166
7.2 Concept exploration phase fl ow diagram 170
7.3 Simple requirements development process 171
7.4 Triumvirate of conceptual design 175
7.5 Hierarchy of scenarios 177
7.6 Function category versus functional media 181
8.1 Concept defi nition phase in system life cycle 198
8.2 Concept defi nition phase fl ow diagram 202
8.3 IDEF0 functional model structure 208
8.4 Functional block diagram of a standard coffeemaker 210
8.5 Traditional view of architecture 223
8.6 DODAF version 2.0 viewpoints 227
8.7 UML models 229
8.8 Use case diagram 231
8.9 UML activity diagram 233
8.10 UML sequence diagram 234
8.11 Example of a class association 235
8.12 Example of a class generalization association 236
8.13 Class diagram of the library check - out system 237
8.14 SysML models 237
8.15 SysML requirements diagram 238
37. 8.16 SysML block defi nition 240
8.17 SysML block associations 241
8.18a SysML functional hierarchy tree 242
8.18b SysML activity diagram 242
8.19 Baker ’ s MDSD subprocesses 244
8.20 Baker ’ s information model for MDSD 244
9.1 Basic decision - making process 256
9.2 Traditional hierarchical block diagram 265
9.3 Context diagram of a passenger aircraft 266
9.4 Air defense functional fl ow block diagram 267
fbetw01.indd xivfbetw01.indd xiv 2/9/2011 6:29:47
PM2/9/2011 6:29:47 PM
LIST OF ILLUSTRATIONS xv
9.5 System effectiveness simulation 275
9.6 Hardware - in - the - loop simulation 277
9.7 Virtual reality simulation 280
9.8 Candidate utility functions 289
9.9 Criteria profi le 290
9.10 Union of two events 297
9.11 Conditional events 297
9.12 AHP example 300
9.13 AHP results 301
9.14 Decision tree example 302
9.15 Decision path 302
9.16 Decision tree solved 303
9.17 Utility function 304
9.18 Decision tree solved with a utility function 304
9.19 Example of cost - effectiveness integration 305
9.20 QFD house of quality 307
10.1 Advanced development phase in system life cycle 318
10.2 Advanced development phase fl ow diagram 321
38. 10.3 Test and evaluation process of a system element 345
11.1 IEEE software systems engineering process 357
11.2 Software hierarchy 359
11.3 Notional 3 - tier architecture 359
11.4 Classical waterfall software development cycle 367
11.5 Software incremental model 369
11.6 Spiral model 370
11.7 State transition diagram in concurrent development
model 371
11.8 User needs, software requirements and specifi cations
376
11.9 Software generation process 376
11.10 Principles of modular partitioning 379
11.11 Functional fl ow block diagram example 381
11.12 Data fl ow diagram: library checkout 381
11.13 Robustness diagram: library checkout 384
12.1 Engineering design phase in system life cycle 410
12.2 Engineering design phase in relation to integration and
evaluation 411
12.3 Engineering design phase fl ow diagram 413
13.1 Integration and evaluation phase in system life cycle
445
13.2 Integration and evaluation phase in relation to
engineering design 445
13.3 System test and evaluation team 446
13.4 System element test confi guration 456
13.5 Subsystems test confi guration 459
13.6a Operation of a passenger airliner 469
13.6b Operational testing of an airliner 469
13.7 Test realism versus cost 471
14.1 Production phase in system life cycle 484
14.2 Production phase overlap with adjacent phases 485
fbetw01.indd xvfbetw01.indd xv 2/9/2011 6:29:47
PM2/9/2011 6:29:47 PM
39. xvi LIST OF ILLUSTRATIONS
14.3 Production operation system 494
15.1 Operations and support phase in system life cycle 506
15.2 System operations history 507
15.3 Non - disruptive installation via simulation 510
15.4 Non - disruptive installation via a duplicate system 511
fbetw01.indd xvifbetw01.indd xvi 2/9/2011 6:29:47
PM2/9/2011 6:29:47 PM
xvii
1.1 Examples of Engineered Complex Systems: Signal and
Data Systems 11
1.2 Examples of Engineered Complex Systems: Material and
Energy
Systems 11
2.1 Comparison of Systems Perspectives 33
2.2 Systems Engineering Activities and Documents 38
3.1 System Design Hierarchy 43
3.2 System Functional Elements 47
3.3 Component Design Elements 49
3.4 Examples of Interface Elements 60
4.1 Evolution of System Materialization through the System
Life Cycle 84
4.2 Evolution of System Representation 88
4.3 Systems Engineering Method over Life Cycle 102
5.1 System Product WBS Partial Breakdown Structure 114
5.2 Risk Likelihood 125
5.3 Risk Criticality 125
40. 5.4 Sample Risk Plan Worksheet 128
6.1 Status of System Materialization at the Needs Analysis
Phase 143
7.1 Status of System Materialization of the Concept
Exploration Phase 168
8.1 Status of System Materialization of Concept Defi nition
Phase 200
8.2 Use Case Example — “ Check - out Book ” 232
9.1 Decision Framework 259
9.2 Simon’s Decision Process 261
9.3 Weighted Sum Integration of Selection Criteria 288
9.4 Weighted Sum of Actual Measurement 289
9.5 Weighted Sum of Utility Scores 290
9.6 Trade-Off Matrix Example 293
10.1 Status of System Materialization at the Advanced
Development Phase 320
10.2 Development of New Components 326
10.3 Selected Critical Characteristics of System Functional
Elements 329
10.4 Some Examples of Special Materials 335
11.1 Software Types 361
LIST OF TABLES
fbetw02.indd xviifbetw02.indd xvii 2/9/2011 6:29:55
PM2/9/2011 6:29:55 PM
xviii LIST OF TABLES
11.2 Categories of Software - Dominated Systems 362
11.3 Differences between Hardware and Software 364
11.4 Systems Engineering Life Cycle and the Waterfall Model
368
11.5 Commonly Used Computer Languages 387
41. 11.6 Some Special - Purpose Computer Languages 388
11.7 Characteristics of Prototypes 390
11.8 Comparison of Computer Interface Modes 391
11.9 Capability Levels 398
11.10 Maturity Levels 399
12.1 Status of System Materialization at the Engineering
Design Phase 412
12.2 Confi guration Baselines 437
13.1 Status of System Materialization at the Integration and
Evaluation
Phase 448
13.2 System Integration and Evaluation Process 449
13.3 Parallels between System Development and Test and
Evaluation
(T & E) Planning 451
fbetw02.indd xviiifbetw02.indd xviii 2/9/2011 6:29:55
PM2/9/2011 6:29:55 PM
xix
It is an incredible honor and privilege to follow in the
footsteps of an individual who
had a profound infl uence on the course of history and the fi eld
of systems engineering.
Since publication of the fi rst edition of this book, the fi eld of
systems engineering has
seen signifi cant advances, including a signifi cant increase in
recognition of the disci-
pline, as measured by the number of conferences, symposia,
journals, articles, and
books available on this crucial subject. Clearly, the fi eld has
reached a high level of
42. maturity and is destined for continued growth. Unfortunately,
the fi eld has also seen
some sorrowful losses, including one of the original authors,
Alexander Kossiakoff,
who passed away just 2 years after the publication of the book.
His vision, innovation,
excitement, and perseverance were contagious to all who
worked with him and he is
missed by the community. Fortunately, his vision remains and
continues to be the
driving force behind this book. It is with great pride that we
dedicate this second edition
to the enduring legacy of Alexander Ivanovitch Kossiakoff.
ALEXANDER KOSSIAKOFF, 1914 – 2005
Alexander Kossiakoff, known to so many as “ Kossy, ” gave
shape and direction to the
Johns Hopkins University Applied Physics Laboratory as its
director from 1969 to
1980. His work helped defend our nation, enhance the
capabilities of our military,
pushed technology in new and exciting directions, and bring
successive new genera-
tions to an understanding of the unique challenges and
opportunities of systems engi-
neering. In 1980, recognizing the need to improve the training
and education of technical
professionals, he started the master of science degree program
at Johns Hopkins
University in Technical Management and later expanded it to
Systems Engineering,
one of the fi rst programs of its kind.
Today, the systems engineering program he founded is the
largest part - time gradu-
43. ate program in the United States, with students enrolled from
around the world in
classroom, distance, and organizational partnership venues; it
continues to evolve as
the fi eld expands and teaching venues embrace new
technologies, setting the standard
for graduate programs in systems engineering. The fi rst edition
of the book is the foun-
dational systems engineering textbook for colleges and
universities worldwide.
PREFACE TO THE SECOND
EDITION
fpref01.indd xixfpref01.indd xix 2/8/2011 3:49:23
PM2/8/2011 3:49:23 PM
xx PREFACE TO THE SECOND EDITION
OBJECTIVES OF THE SECOND EDITION
Traditional engineering disciplines do not provide the training,
education, and experi-
ence necessary to ensure the successful development of a large,
complex system
program from inception to operational use. The advocacy of the
systems engineering
viewpoint and the goal for the practitioners to think like a
systems engineer are still
the major premises of this book.
This second edition of Systems Engineering Principles and
Practice continues to
be intended as a graduate - level textbook for courses
44. introducing the fi eld and practice
of systems engineering. We continue the tradition of utilizing
models to assist students
in grasping abstract concepts presented in the book. The fi ve
basic models of the fi rst
edition are retained, with only minor refi nements to refl ect
current thinking. Additionally,
the emphasis on application and practice is retained throughout
and focuses on students
pursuing their educational careers in parallel with their
professional careers. Detailed
mathematics and other technical fi elds are not explored in
depth, providing the greatest
range of students who may benefi t, nor are traditional
engineering disciplines provided
in detail, which would violate the book ’ s intended scope.
The updates and additions to the fi rst edition revolve around
the changes occurring
in the fi eld of systems engineering since the original
publication. Special attention was
made in the following areas :
• The Systems Engineer ’ s Career. An expanded
discussion is presented on
the career of the systems engineer. In recent years, systems
engineering
has been recognized by many companies and organizations as a
separate fi eld,
and the position of “ systems engineer ” has been formalized.
Therefore, we
present a model of the systems engineer ’ s career to help guide
prospective
professionals.
• The Systems Engineering Landscape. The only new
45. chapter introduced in the
second edition is titled by the same name and reinforces the
concept of the
systems engineering viewpoint. Expanded discussions of the
implications of this
viewpoint have been offered.
• System Boundaries. Supplemental material has been
introduced defi ning and
expanding our discussion on the concept of the system
boundary. Through the
use of the book in graduate - level education, the authors
recognized an inherent
misunderstanding of this concept — students in general have
been unable to rec-
ognize the boundary between the system and its environment.
This area has been
strengthened throughout the book.
• System Complexity. Signifi cant research in the area
of system complexity is now
available and has been addressed. Concepts such as system of
systems engineer-
ing, complex systems management, and enterprise systems
engineering are intro-
duced to the student as a hierarchy of complexity, of which
systems engineering
forms the foundation.
• Systems Architecting. Since the original publication,
the fi eld of systems archi-
tecting has expanded signifi cantly, and the tools, techniques,
and practices of this
fpref01.indd xxfpref01.indd xx 2/8/2011 3:49:23
PM2/8/2011 3:49:23 PM
46. PREFACE TO THE SECOND EDITION xxi
fi eld have been incorporated into the concept exploration and
defi nition chapters.
New models and frameworks for both traditional structured
analysis and object -
oriented analysis techniques are described and examples are
provided, including
an expanded description of the Unifi ed Modeling Language and
the Systems
Modeling Language. Finally, the extension of these new
methodologies, model -
based systems engineering, is introduced.
• Decision Making and Support. The chapter on systems
engineering decision
tools has been updated and expanded to introduce the systems
engineering
student to the variety of decisions required in this fi eld, and the
modern pro-
cesses, tools, and techniques that are available for use. The
chapter has also been
moved from the original special topics part of the book.
• Software Systems Engineering. The chapter on
software systems engineering has
been extensively revised to incorporate modern software
engineering techniques,
principles, and concepts. Descriptions of modern software
development life
cycle models, such as the agile development model, have been
expanded to
refl ect current practices. Moreover, the section on capability
47. maturity models has
been updated to refl ect the current integrated model. This
chapter has also been
moved out of the special topics part and introduced as a full
partner of advanced
development and engineering design.
In addition to the topics mentioned above, the chapter
summaries have been refor-
matted for easier understanding, and the lists of problems and
references have been
updated and expanded. Lastly, feedback, opinions, and
recommendations from graduate
students have been incorporated where the wording or
presentation was awkward or
unclear.
CONTENT DESCRIPTION
This book continues to be used to support the core courses of
the Johns Hopkins
University Master of Science in Systems Engineering program
and is now a primary
textbook used throughout the United States and in several other
countries. Many pro-
grams have transitioned to online or distance instruction; the
second edition was written
with distance teaching in mind, and offers additional examples.
The length of the book has grown, with the updates and new
material refl ecting
the expansion of the fi eld itself.
The second edition now has four parts:
• Part I . The Foundation of Systems Engineering,
48. consisting of Chapters 1 – 5 ,
describes the origins and structure of modern systems, the
current fi eld of systems
engineering, the structured development process of complex
systems, and the
organization of system development projects.
• Part II . Concept Development, consisting of Chapters
6 – 9 , describes the early
stages of the system life cycle in which a need for a new system
is demonstrated,
fpref01.indd xxifpref01.indd xxi 2/8/2011 3:49:23
PM2/8/2011 3:49:23 PM
xxii PREFACE TO THE SECOND EDITION
its requirements identifi ed, alternative implementations
developed, and key
program and technical decisions made.
• Part III . Engineering Development, consisting of
Chapters 10 – 13 , describes the
later stages of the system life cycle, in which the system
building blocks are
engineered (to include both software and hardware subsystems)
and the total
system is integrated and evaluated in an operational
environment.
• Part IV . Postdevelopment, consisting of Chapters 14
and 15 , describes the roles
of systems in the production, operation, and support phases of
the system life
49. cycle and what domain knowledge of these phases a systems
engineer should
acquire.
Each chapter contains a summary, homework problems, and
bibliography.
ACKNOWLEDGMENTS
The authors of the second edition gratefully acknowledge the
family of Dr. Kossiakoff
and Mr. William Sweet for their encouragement and support of
a second edition to the
original book. As with the fi rst edition, the authors gratefully
acknowledge the many
contributions made by the present and past faculties of the
Johns Hopkins University
Systems Engineering graduate program. Their sharp insight and
recommendations on
improvements to the fi rst edition have been invaluable in
framing this publication.
Particular thanks are due to E. A. Smyth for his insightful
review of the manuscript.
Finally, we are exceedingly grateful to our families — Judy
Seymour and Michele
and August Biemer — for their encouragement, patience, and
unfailing support, even
when they were continually asked to sacrifi ce, and the end
never seemed to be
within reach.
Much of the work in preparing this book was supported as part
of the educational
mission of the Johns Hopkins University Applied Physics
Laboratory.
50. Samuel J. Seymour
Steven M. Biemer
2010
fpref01.indd xxiifpref01.indd xxii 2/8/2011 3:49:23
PM2/8/2011 3:49:23 PM
xxiii
Learning how to be a successful systems engineer is entirely
different from learning
how to excel at a traditional engineering discipline. It requires
developing the ability
to think in a special way, to acquire the “ systems engineering
viewpoint, ” and to make
the central objective the system as a whole and the success of
its mission. The systems
engineer faces three directions: the system user ’ s needs and
concerns, the project man-
ager ’ s fi nancial and schedule constraints, and the capabilities
and ambitions of the
engineering specialists who have to develop and build the
elements of the system. This
requires learning enough of the language and basic principles of
each of the three
constituencies to understand their requirements and to negotiate
balanced solutions
acceptable to all. The role of interdisciplinary leadership is the
key contribution and
principal challenge of systems engineering and it is absolutely
indispensable to the
51. successful development of modern complex systems.
1.1 OBJECTIVES
Systems Engineering Principles and Practice is a textbook
designed to help students
learn to think like systems engineers. Students seeking to learn
systems engineering
after mastering a traditional engineering discipline often fi nd
the subject highly abstract
and ambiguous. To help make systems engineering more
tangible and easier to grasp,
the book provides several models: (1) a hierarchical model of
complex systems, showing
them to be composed of a set of commonly occurring building
blocks or components;
(2) a system life cycle model derived from existing models but
more explicitly related
to evolving engineering activities and participants; (3) a model
of the steps in the
systems engineering method and their iterative application to
each phase of the life
cycle; (4) a concept of “ materialization ” that represents the
stepwise evolution of an
abstract concept to an engineered, integrated, and validated
system; and (5) repeated
references to the specifi c responsibilities of systems engineers
as they evolve during
the system life cycle and to the scope of what a systems
engineer must know to perform
these effectively. The book ’ s signifi cantly different approach
is intended to complement
the several excellent existing textbooks that concentrate on the
quantitative and analyti-
cal aspects of systems engineering.
52. PREFACE TO THE FIRST EDITION
fpref02.indd xxiiifpref02.indd xxiii 2/8/2011 3:49:24
PM2/8/2011 3:49:24 PM
xxiv PREFACE TO THE FIRST EDITION
Particular attention is devoted to systems engineers as
professionals, their respon-
sibilities as part of a major system development project, and the
knowledge, skills, and
mind - set they must acquire to be successful. The book stresses
that they must be inno-
vative and resourceful, as well as systematic and disciplined. It
describes the special
functions and responsibilities of systems engineers in
comparison with those of system
analysts, design specialists, test engineers, project managers,
and other members of the
system development team. While the book describes the
necessary processes that
systems engineers must know and execute, it stresses the
leadership, problem - solving,
and innovative skills necessary for success.
The function of systems engineering as defi ned here is to “
guide the engineering
of complex systems. ” To learn how to be a good guide requires
years of practice and
the help and advice of a more experienced guide who knows “
the way. ” The purpose
of this book is to provide a signifi cant measure of such help
and advice through the
organized collective experience of the authors and other
53. contributors.
This book is intended for graduate engineers or scientists who
aspire to or are
already engaged in careers in systems engineering, project
management, or engineering
management. Its main audience is expected to be engineers
educated in a single disci-
pline, either hardware or software, who wish to broaden their
knowledge so as to deal
with systems problems. It is written with a minimum of
mathematics and specialized
jargon so that it should also be useful to managers of technical
projects or organizations,
as well as to senior undergraduates.
1.2 ORIGIN AND CONTENTS
The main portion of the book has been used for the past 5 years
to support the fi ve core
courses of the Johns Hopkins University Master of Science in
Systems Engineering
program and is thoroughly class tested. It has also been used
successfully as a text for
distance course offerings. In addition, the book is well suited to
support short courses
and in - house training.
The book consists of 14 chapters grouped into fi ve parts :
• Part I . The Foundations of Systems Engineering,
consisting of Chapters 1 – 4 ,
describes the origin and structure of modern systems, the
stepwise development
process of complex systems, and the organization of system
development
54. projects.
• Part II . Concept Development, consisting of Chapters
5 – 7 , describes the fi rst
stage of the system life cycle in which a need for a new system
is demonstrated,
its requirements are developed, and a specifi c preferred
implementation concept
is selected.
• Part III . Engineering Development, consisting of
Chapters 8 – 10 , describes the
second stage of the system life cycle, in which the system
building blocks are
engineered and the total system is integrated and evaluated in
an operational
environment.
fpref02.indd xxivfpref02.indd xxiv 2/8/2011 3:49:24
PM2/8/2011 3:49:24 PM
PREFACE TO THE FIRST EDITION xxv
• Part IV . Postdevelopment, consisting of Chapters 11
and 12 , describes the role
of systems engineering in the production, operation, and support
phases of the
system life cycle, and what domain knowledge of these phases
in the system life
cycle a systems engineer should acquire.
• Part V . Special Topics consists of Chapters 13 and
14 . Chapter 13 describes the
pervasive role of software throughout system development, and
55. Chapter 14
addresses the application of modeling, simulation, and trade -
off analysis as
systems engineering decision tools.
Each chapter also contains a summary, homework problems,
and a bibliography.
A glossary of important terms is also included. The chapter
summaries are formatted
to facilitate their use in lecture viewgraphs.
ACKNOWLEDGMENTS
The authors gratefully acknowledge the many contributions
made by the present and
past faculties of the Johns Hopkins University Systems
Engineering Masters program.
Particular thanks are due to S. M. Biemer, J. B. Chism, R. S.
Grossman, D. C. Mitchell,
J. W. Schneider, R. M. Schulmeyer, T. P. Sleight, G. D. Smith,
R. J. Thompson, and S.
P. Yanek, for their astute criticism of passages that may have
been dear to our hearts
but are in need of repairs.
An even larger debt is owed to Ben E. Amster, who was one of
the originators and
the initial faculty of the Johns Hopkins University Systems
Engineering program.
Though not directly involved in the original writing, he
enhanced the text and diagrams
by adding many of his own insights and fi ne - tuned the entire
text for meaning and
clarity, applying his 30 years ’ experience as a systems
engineer to great advantage.
56. We especially want to thank H. J. Gravagna for her outstanding
expertise and
inexhaustible patience in typing and editing the innumerable
rewrites of the drafts of
the manuscript. These were issued to successive classes of
systems engineering students
as the book evolved over the past 3 years. It was she who kept
the focus on the fi nal
product and provided invaluable assistance with the production
of this work.
Finally, we are eternally grateful to our wives, Arabelle and
Kathleen, for their
encouragement, patience, and unfailing support, especially
when the written words
came hard and the end seemed beyond our reach.
Much of the work in preparing this book was supported as part
of the educational
mission of the Johns Hopkins Applied Physics Laboratory.
Alexander Kossiakoff
William N. Sweet
2002
fpref02.indd xxvfpref02.indd xxv 2/8/2011 3:49:24
PM2/8/2011 3:49:24 PM
fpref02.indd xxvifpref02.indd xxvi 2/8/2011 3:49:24
PM2/8/2011 3:49:24 PM
57. 1
Part I provides a multidimensional framework that
interrelates the basic principles of
systems engineering, and helps to organize the areas of
knowledge that are required to
master this subject. The dimensions of this framework include
1. a hierarchical model of the structure of complex systems;
2. a set of commonly occurring functional and physical
system building blocks;
3. a systems engineering life cycle, integrating the features
of the U.S Department
of Defense, ISO/IEC, IEEE, and NSPE models;
4. four basic steps of the systems engineering method that
are iterated during each
phase of the life cycle;
5. three capabilities differentiating project management,
design specialization, and
systems engineering;
6. three different technical orientations of a scientist, a
mathematician, and an
engineer and how they combine in the orientation of a systems
engineer; and
7. a concept of “ materialization ” that measures the
degree of transformation of a
system element from a requirement to a fully implemented part
of a real system.
59. terms of the system
hierarchy.
Chapter 4 derives the concept of the systems engineering life
cycle, which sets the
framework for the evolution of a complex system from a
perceived need to operation
and disposal. This framework is systematically applied
throughout Parts II – IV of the
book, each part addressing the key responsibilities of systems
engineering in the cor-
responding phase of the life cycle.
Finally, Chapter 5 describes the key parts that systems
engineering plays in the
management of system development projects. It defi nes the
basic organization and
the planning documents of a system development project, with a
major emphasis on
the management of program risks.
p01.indd 2p01.indd 2 2/9/2011 4:16:37 PM2/9/2011
4:16:37 PM
3
1.1 WHAT IS SYSTEMS ENGINEERING?
There are many ways in which to defi ne systems engineering.
For the purposes of this
book, we will use the following defi nition:
The function of systems engineering is to guide the
60. engineering of complex systems .
The words in this defi nition are used in their conventional
meanings, as described
further below.
To guide is defi ned as “ to lead, manage, or direct, usually
based on the superior
experience in pursuing a given course ” and “ to show the way.
” This characterization
emphasizes the process of selecting the path for others to follow
from among many
possible courses — a primary function of systems engineering.
A dictionary defi nition
of engineering is “ the application of scientifi c principles to
practical ends; as the design,
construction and operation of effi cient and economical
structures, equipment, and
systems. ” In this defi nition, the terms “ effi cient ” and “
economical ” are particular con-
tributions of good systems engineering.
The word “ system, ” as is the case with most common
English words, has a
very broad meaning. A frequently used defi nition of a system is
“ a set of interrelated
1
SYSTEMS ENGINEERING
AND THE WORLD OF
MODERN SYSTEMS
Systems Engineering Principles and Practice, Second Edition.
Alexander Kossiakoff, William N. Sweet,
Samuel J. Seymour, and Steven M. Biemer
62. as being unique or superior to those used in other textbooks,
each of which defi nes
them somewhat differently. In order to avoid any potential
misunderstanding, the
meaning of these terms as used in this book is defi ned at the
very outset, before going
on to the more important subjects of the responsibilities,
problems, activities, and tools
of systems engineering.
Systems Engineering and Traditional Engineering Disciplines
From the above defi nition, it can be seen that systems
engineering differs from mechani-
cal, electrical, and other engineering disciplines in several
important ways:
1. Systems engineering is focused on the system as a whole;
it emphasizes its total
operation. It looks at the system from the outside, that is, at its
interactions with
other systems and the environment, as well as from the inside. It
is concerned
not only with the engineering design of the system but also with
external factors,
which can signifi cantly constrain the design. These include the
identifi cation of
customer needs, the system operational environment, interfacing
systems, logis-
tics support requirements, the capabilities of operating
personnel, and such other
factors as must be correctly refl ected in system requirements
documents and
accommodated in the system design.
2. While the primary purpose of systems engineering is to
63. guide, this does not
mean that systems engineers do not themselves play a key role
in system design.
On the contrary, they are responsible for leading the formative
(concept devel-
opment) stage of a new system development, which culminates
in the functional
design of the system refl ecting the needs of the user. Important
design decisions
at this stage cannot be based entirely on quantitative
knowledge, as they are for
the traditional engineering disciplines, but rather must often
rely on qualitative
judgments balancing a variety of incommensurate quantities and
utilizing expe-
rience in a variety of disciplines, especially when dealing with
new
technology.
3. Systems engineering bridges the traditional engineering
disciplines. The diver-
sity of the elements in a complex system requires different
engineering disci-
c01.indd 4c01.indd 4 2/8/2011 11:04:29 AM2/8/2011
11:04:29 AM
ORIGINS OF SYSTEMS ENGINEERING 5
plines to be involved in their design and development. For the
system to perform
correctly, each system element must function properly in
combination with one
or more other system elements. Implementation of these
64. interrelated functions
is dependent on a complex set of physical and functional
interactions between
separately designed elements. Thus, the various elements cannot
be engineered
independently of one another and then simply assembled to
produce a working
system. Rather, systems engineers must guide and coordinate
the design of each
individual element as necessary to assure that the interactions
and interfaces
between system elements are compatible and mutually
supporting. Such coor-
dination is especially important when individual system
elements are designed,
tested, and supplied by different organizations.
Systems Engineering and Project Management
The engineering of a new complex system usually begins with
an exploratory stage in
which a new system concept is evolved to meet a recognized
need or to exploit a tech-
nological opportunity. When the decision is made to engineer
the new concept into an
operational system, the resulting effort is inherently a major
enterprise, which typically
requires many people, with diverse skills, to devote years of
effort to bring the system
from concept to operational use.
The magnitude and complexity of the effort to engineer a new
system requires
a dedicated team to lead and coordinate its execution. Such an
enterprise is called
a “ project ” and is directed by a project manager aided by a
65. staff. Systems engineering
is an inherent part of project management — the part that is
concerned with guiding
the engineering effort itself — setting its objectives, guiding its
execution, evaluating
its results, and prescribing necessary corrective actions to keep
it on course. The man-
agement of the planning and control aspects of the project fi
scal, contractual, and
customer relations is supported by systems engineering but is
usually not considered
to be part of the systems engineering function. This subject is
described in more detail
in Chapter 5 .
Recognition of the importance of systems engineering by every
participant in a
system development project is essential for its effective
implementation. To accomplish
this, it is often useful to formally assign the leader of the
systems engineering team to
a recognized position of technical responsibility and authority
within the project.
1.2 ORIGINS OF SYSTEMS ENGINEERING
No particular date can be associated with the origins of systems
engineering. Systems
engineering principles have been practiced at some level since
the building of the pyra-
mids and probably before. (The Bible records that Noah ’ s Ark
was built to a system
specifi cation.)
The recognition of systems engineering as a distinct activity is
often associated
66. with the effects of World War II, and especially the 1950s and
1960s when a number
of textbooks were published that fi rst identifi ed systems
engineering as a distinct
c01.indd 5c01.indd 5 2/8/2011 11:04:29 AM2/8/2011
11:04:29 AM
6 SYSTEMS ENGINEERING AND THE WORLD OF MODERN
SYSTEMS
discipline and defi ned its place in the engineering of systems.
More generally, the
recognition of systems engineering as a unique activity evolved
as a necessary corollary
to the rapid growth of technology, and its application to major
military and commercial
operations during the second half of the twentieth century.
The global confl agration of World War II provided a
tremendous spur to the
advancement of technology in order to gain a military advantage
for one side or the
other. The development of high - performance aircraft, military
radar, the proximity fuse,
the German VI and V2 missiles, and especially the atomic bomb
required revolutionary
advances in the application of energy, materials, and
information. These systems were
complex, combining multiple technical disciplines, and their
development posed engi-
neering challenges signifi cantly beyond those that had been
presented by their more
conventional predecessors. Moreover, the compressed
67. development time schedules
imposed by wartime imperatives necessitated a level of
organization and effi ciency that
required new approaches in program planning, technical
coordination, and engineering
management. Systems engineering, as we know it today,
developed to meet these
challenges.
During the Cold War of the 1950s, 1960s, and 1970s, military
requirements con-
tinued to drive the growth of technology in jet propulsion,
control systems, and materi-
als. However, another development, that of solid - state
electronics, has had perhaps a
more profound effect on technological growth. This, to a large
extent, made possible
the still evolving “ information age, ” in which computing,
networks, and communica-
tions are extending the power and reach of systems far beyond
their previous limits.
Particularly signifi cant in this connection is the development of
the digital computer
and the associated software technology driving it, which
increasingly is leading to the
replacement of human control of systems by automation.
Computer control is qualita-
tively increasing the complexity of systems and is a particularly
important concern of
systems engineering.
The relation of modern systems engineering to its origins can
be best understood
in terms of three basic factors:
1. Advancing Technology, which provide opportunities
68. for increasing system
capabilities, but introduces development risks that require
systems engineering
management; nowhere is this more evident than in the world of
automation.
Technology advances in human – system interfaces, robotics,
and software make
this particular area one of the fastest growing technologies
affecting system
design.
2. Competition, whose various forms require seeking
superior (and more
advanced) system solutions through the use of system - level
trade - offs among
alternative approaches.
3. Specialization, which requires the partitioning of the
system into building
blocks corresponding to specifi c product types that can be
designed and built
by specialists, and strict management of their interfaces and
interactions.
These factors are discussed in the following paragraphs.
c01.indd 6c01.indd 6 2/8/2011 11:04:29 AM2/8/2011
11:04:29 AM
ORIGINS OF SYSTEMS ENGINEERING 7
Advancing Technology: Risks
The explosive growth of technology in the latter half of the
69. twentieth century and
into this century has been the single largest factor in the
emergence of systems engi-
neering as an essential ingredient in the engineering of complex
systems. Advancing
technology has not only greatly extended the capabilities of
earlier systems, such as
aircraft, telecommunications, and power plants, but has also
created entirely new
systems such as those based on jet propulsion, satellite
communications and navigation,
and a host of computer - based systems for manufacturing, fi
nance, transportation,
entertainment, health care, and other products and services.
Advances in technology
have not only affected the nature of products but have also
fundamentally changed
the way they are engineered, produced, and operated. These are
particularly important
in early phases of system development, as described in
Conceptual Exploration, in
Chapter 7 .
Modern technology has had a profound effect on the very
approach to engineering.
Traditionally, engineering applies known principles to practical
ends. Innovation,
however, produces new materials, devices, and processes,
whose characteristics are not
yet fully measured or understood. The application of these to
the engineering of new
systems thus increases the risk of encountering unexpected
properties and effects that
might impact system performance and might require costly
changes and program
delays.
70. However, failure to apply the latest technology to system
development also carries
risks. These are the risks of producing an inferior system, one
that could become pre-
maturely obsolete. If a competitor succeeds in overcoming such
problems as may be
encountered in using advanced technology, the competing
approach is likely to be
superior. The successful entrepreneurial organization will thus
assume carefully selected
technological risks and surmount them by skillful design,
systems engineering, and
program management.
The systems engineering approach to the early application of
new technology is
embodied in the practice of “ risk management. ” Risk
management is a process of
dealing with calculated risks through a process of analysis,
development, test, and
engineering oversight. It is described more fully in Chapters 5
and 9 .
Dealing with risks is one of the essential tasks of systems
engineering, requiring
a broad knowledge of the total system and its critical elements.
In particular, systems
engineering is central to the decision of how to achieve the best
balance of risks, that
is, which system elements should best take advantage of new
technology and which
should be based on proven components, and how the risks
incurred should be reduced
by development and testing.
71. The development of the digital computer and software
technology noted earlier
deserves special mention. This development has led to an
enormous increase in the
automation of a wide array of control functions for use in
factories, offi ces, hospitals,
and throughout society. Automation, most of it being concerned
with information pro-
cessing hardware and software, and its sister technology,
autonomy, which adds in
capability of command and control, is the fastest growing and
most powerful single
infl uence on the engineering of modern systems.
c01.indd 7c01.indd 7 2/8/2011 11:04:29 AM2/8/2011
11:04:29 AM
8 SYSTEMS ENGINEERING AND THE WORLD OF MODERN
SYSTEMS
The increase in automation has had an enormous impact on
people who operate
systems, decreasing their number but often requiring higher
skills and therefore special
training. Human – machine interfaces and other people – system
interactions are particu-
lar concerns of systems engineering.
Software continues to be a growing engineering medium whose
power and versatil-
ity has resulted in its use in preference to hardware for the
implementation of a growing
fraction of system functions. Thus, the performance of modern
systems increasingly
72. depends on the proper design and maintenance of software
components. As a result,
more and more of the systems engineering effort has had to be
directed to the control
of software design and its application.
Competition: Trade - offs
Competitive pressures on the system development process
occur at several different
levels. In the case of defense systems, a primary drive comes
from the increasing mili-
tary capabilities of potential adversaries, which correspondingly
decrease the effective-
ness of systems designed to defeat them. Such pressures
eventually force a development
program to redress the military balance with a new and more
capable system or a major
upgrade of an existing one.
Another source of competition comes with the use of
competitive contracting for
the development of new system capabilities. Throughout the
competitive period, which
may last through the initial engineering of a new system, each
contractor seeks to devise
the most cost - effective program to provide a superior product.
In developing a commercial product, there are nearly always
other companies that
compete in the same market. In this case, the objective is to
develop a new market or
to obtain an increased market share by producing a superior
product ahead of the com-
petition, with an edge that will maintain a lead for a number of
years. The above
73. approaches nearly always apply the most recent technology in
an effort to gain a com-
petitive advantage.
Securing the large sums of money needed to fund the
development of a new
complex system also involves competition on quite a different
level. In particular, both
government agencies and industrial companies have many more
calls on their resources
than they can accommodate and hence must carefully weigh the
relative payoff of
proposed programs. This is a primary reason for requiring a
phased approach in new
system development efforts, through the requirement for justifi
cation and formal
approval to proceed with the increasingly expensive later
phases. The results of each
phase of a major development must convince decision makers
that the end objectives
are highly likely to be attained within the projected cost and
schedule.
On a still different basis, the competition among the essential
characteristics of
the system is always a major consideration in its development.
For example, there is
always competition between performance, cost, and schedule,
and it is impossible to
optimize all three at once. Many programs have failed by
striving to achieve levels
of performance that proved unaffordable. Similarly, the various
performance parame-
ters of a vehicle, such as speed and range, are not independent
of one another; the
effi ciency of most vehicles, and hence their operating range,
74. decreases at higher speeds.
c01.indd 8c01.indd 8 2/8/2011 11:04:29 AM2/8/2011
11:04:29 AM
ORIGINS OF SYSTEMS ENGINEERING 9
Thus, it is necessary to examine alternatives in which these
characteristics are allowed
to vary and to select the combination that best balances their
values for the benefi t of
the user.
All of the forms of competition exert pressure on the system
development process
to produce the best performing, most affordable system, in the
least possible time. The
process of selecting the most desirable approach requires the
examination of numerous
potential alternatives and the exercise of a breadth of technical
knowledge and judgment
that only experienced systems engineers possess. This is often
referred to as “ trade - off
analysis ” and forms one of the basic practices of systems
engineering.
Specialization: Interfaces
A complex system that performs a number of different
functions must of necessity be
confi gured in such a way that each major function is embodied
in a separate component
capable of being specifi ed, developed, built, and tested as an
individual entity. Such a
75. subdivision takes advantage of the expertise of organizations
specializing in particular
types of products, and hence is capable of engineering and
producing components of
the highest quality at the lowest cost. Chapter 3 describes the
kind of functional and
physical building blocks that make up most modern systems.
The immensity and diversity of engineering knowledge, which
is still growing, has
made it necessary to divide the education and practice of
engineering into a number of
specialties, such as mechanical, electrical, aeronautical, and so
on. To acquire the neces-
sary depth of knowledge in any one of these fi elds, further
specialization is needed,
into such subfi elds as robotics, digital design, and fl uid
dynamics. Thus, engineering
specialization is a predominant condition in the fi eld of
engineering and manufacturing
and must be recognized as a basic condition in the system
development process.
Each engineering specialty has developed a set of specialized
tools and facilities
to aid in the design and manufacture of its associated products.
Large and small com-
panies have organized around one or several engineering groups
to develop and manu-
facture devices to meet the needs of the commercial market or
of the system - oriented
industry. The development of interchangeable parts and
automated assembly has been
one of the triumphs of the U.S. industry.
The convenience of subdividing complex systems into
76. individual building blocks
has a price: that of integrating these disparate parts into an effi
cient, smoothly operating
system. Integration means that each building block fi ts
perfectly with its neighbors and
with the external environment with which it comes into contact.
The “ fi t ” must be not
only physical but also functional; that is, its design will both
affect the design charac-
teristics and behavior of other elements, and will be affected by
them, to produce the
exact response that the overall system is required to make to
inputs from its environ-
ment. The physical fi t is accomplished at intercomponent
boundaries called interfaces .
The functional relationships are called interactions .
The task of analyzing, specifying, and validating the
component interfaces with
each other and with the external environment is beyond the
expertise of the individual
design specialists and is the province of the systems engineer.
Chapter 3 discusses
further the importance and nature of this responsibility.
c01.indd 9c01.indd 9 2/8/2011 11:04:29 AM2/8/2011
11:04:29 AM
10 SYSTEMS ENGINEERING AND THE WORLD OF
MODERN SYSTEMS
A direct consequence of the subdivision of systems into their
building blocks is
the concept of modularity. Modularity is a measure of the
77. degree of mutual indepen-
dence of the individual system components. An essential goal of
systems engineering
is to achieve a high degree of modularity to make interfaces and
interactions as simple
as possible for effi cient manufacture, system integration, test,
operational maintenance,
reliability, and ease of in - service upgrading. The process of
subdividing a system into
modular building blocks is called “ functional allocation ” and
is another basic tool of
systems engineering.
1.3 EXAMPLES OF SYSTEMS REQUIRING SYSTEMS
ENGINEERING
As noted at the beginning of this chapter, the generic defi
nition of a system as a set of
interrelated components working together as an integrated
whole to achieve some
common objective would fi t most familiar home appliances. A
washing machine con-
sists of a main clothes tub, an electric motor, an agitator, a
pump, a timer, an inner
spinning tub, and various valves, sensors, and controls. It
performs a sequence of timed
operations and auxiliary functions based on a schedule and
operation mode set by the
operator. A refrigerator, microwave oven, dishwasher, vacuum
cleaner, and radio all
perform a number of useful operations in a systematic manner.
However, these appli-
ances involve only one or two engineering disciplines, and their
design is based on
well - established technology. Thus, they fail the criterion of
being complex , and we
78. would not consider the development of a new washer or
refrigerator to involve much
systems engineering as we understand the term, although it
would certainly require a
high order of reliability and cost engineering. Of course, home
appliances increasingly
include clever automatic devices that use newly available
microchips, but these are
usually self - contained add - ons and are not necessary to the
main function of the
appliance.
Since the development of new modern systems is strongly
driven by technological
change, we shall add one more characteristic to a system
requiring systems engineering,
namely, that some of its key elements use advanced technology.
The characteristics of
a system whose development, test, and application require the
practice of systems
engineering are that the system
• is an engineered product and hence satisfi es a specifi ed
need,
• consists of diverse components that have intricate
relationships with one another
and hence is multidisciplinary and relatively complex, and
• uses advanced technology in ways that are central to the
performance of its
primary functions and hence involves development risk and
often a relatively
high cost.
Henceforth, references in this text to an engineered or
79. complex system (or in the
proper context, just system ) will mean the type that has the
three attributes noted above,
that is, is an engineered product, contains diverse components,
and uses advanced
technology. These attributes are, of course, in addition to the
generic defi nition stated
c01.indd 10c01.indd 10 2/8/2011 11:04:29 AM2/8/2011
11:04:29 AM
EXAMPLES OF SYSTEMS REQUIRING SYSTEMS
ENGINEERING 11
earlier and serve to identify the systems of concern to the
systems engineer as those
that require system design, development, integration, test, and
evaluation. In Chapter
2 , we explore the full spectrum of systems complexity and why
the systems engineering
landscape presents a challenge for systems engineers.
Examples of Complex Engineered Systems
To illustrate the types of systems that fi t within the above defi
nition, Tables 1.1 and 1.2
list 10 modern systems and their principal inputs, processes, and
outputs.
TA B L E 1.1. Examples of Engineered Complex Systems:
Signal and Data Systems
System Inputs Process Outputs
80. Weather satellite Images • Data storage
• Transmission
Encoded images
Terminal air traffi c
control system
Aircraft beacon
responses
• Identifi cation
• Tracking
• Identity
• Air tracks
• Communications
Track location system Cargo routing
requests
• Map tracing
• Communication
• Routing information
• Delivered cargo
Airline reservation
system
Travel requests Data management • Reservations
• Tickets
Clinical information
system
81. • Patient ID
• Test records
• Diagnosis
Information
management
• Patient status
• History
• Treatment
TA B L E 1.2. Examples of Engineered Complex Systems:
Material and Energy Systems
System Inputs Process Outputs
Passenger aircraft • Passengers
• Fuel
• Combustion
• Thrust
• Lift
Transported
passengers
Modern harvester
combine
• Grain fi eld
• Fuel
• Cutting
• Threshing
Harvested grain
82. Oil refi nery • Crude oil
• Catalysts
• Energy
• Cracking
• Separation
• Blending
• Gasoline
• Oil products
• Chemicals
Auto assembly plant • Auto parts
• Energy
• Manipulation
• Joining
• Finishing
Assembled auto
Electric power plant • Fuel
• Air
• Power generation
• Regulation
• Electric AC power
• Waste products
c01.indd 11c01.indd 11 2/8/2011 11:04:29 AM2/8/2011
11:04:29 AM
83. 12 SYSTEMS ENGINEERING AND THE WORLD OF
MODERN SYSTEMS
It has been noted that a system consists of a multiplicity of
elements, some of
which may well themselves be complex and deserve to be
considered a system in their
own right. For example, a telephone - switching substation can
well be considered as a
system, with the telephone network considered as a “ system of
systems. ” Such issues
will be discussed more fully in Chapters 2 and 4 , to the
extent necessary for the under-
standing of systems engineering.
Example: A Modern Automobile. A more simple and
familiar system, which
still meets the criteria for an engineered system, is a fully
equipped passenger automo-
bile. It can be considered as a lower limit to more complex
vehicular systems. It is
made up of a large number of diverse components requiring the
combination of several
different disciplines. To operate properly, the components must
work together accu-
rately and effi ciently. Whereas the operating principles of
automobiles are well estab-
lished, modern autos must be designed to operate effi ciently
while at the same time
maintaining very close control of engine emissions, which
requires sophisticated
sensors and computer - controlled mechanisms for injecting fuel
and air. Antilock brakes
are another example of a fi nely tuned automatic automobile
subsystem. Advanced
materials and computer technology are used to an increasing
84. degree in passenger pro-
tection, cruise control, automated navigation and autonomous
driving and parking. The
stringent requirements on cost, reliability, performance,
comfort, safety, and a dozen
other parameters present a number of substantive systems
engineering problems.
Accordingly, an automobile meets the defi nition established
earlier for a system requir-
ing the application of systems engineering, and hence can serve
as a useful example.
An automobile is also an example of a large class of systems
that require active
interaction (control) by a human operator. To some degree, all
systems require such
interaction, but in this case, continuous control is required. In a
very real sense, the
operator (driver) functions as an integral part of the overall
automobile system, serving
as the steering feedback element that detects and corrects
deviations of the car ’ s path
on the road. The design must therefore address as a critical
constraint the inherent
sensing and reaction capabilities of the operator, in addition to
a range of associated
human – machine interfaces such as the design and placement of
controls and displays,
seat position, and so on. Also, while the passengers may not
function as integral ele-
ments of the auto steering system, their associated interfaces
(e.g., weight, seating and
viewing comfort, and safety) must be carefully addressed as
part of the design process.
Nevertheless, since automobiles are developed and delivered
without the human
85. element, for purposes of systems engineering, they may be
addressed as systems in
their own right.
1.4 SYSTEMS ENGINEERING AS A PROFESSION
With the increasing prevalence of complex systems in modern
society, and the essential
role of systems engineering in the development of systems,
systems engineering as a
profession has become widely recognized. Its primary
recognition has come in compa-
nies specializing in the development of large systems. A number
of these have estab-
c01.indd 12c01.indd 12 2/8/2011 11:04:29 AM2/8/2011
11:04:29 AM
SYSTEMS ENGINEERING AS A PROFESSION 13
lished departments of systems engineering and have classifi ed
those engaging in the
process as systems engineers. In addition, global challenges in
health care, communica-
tions, environment, and many other complex areas require
engineering systems methods
to develop viable solutions.
To date, the slowness of recognition of systems engineering as
a career is the fact
that it does not correspond to the traditional academic
engineering disciplines.
Engineering disciplines are built on quantitative relationships,
obeying established
86. physical laws, and measured properties of materials, energy, or
information. Systems
engineering, on the other hand, deals mainly with problems for
which there is incom-
plete knowledge, whose variables do not obey known equations,
and where a balance
must be made among confl icting objectives involving
incommensurate attributes. The
absence of a quantitative knowledge base previously inhibited
the establishment of
systems engineering as a unique discipline.
Despite those obstacles, the recognized need for systems
engineering in industry
and government has spurred the establishment of a number of
academic programs
offering master ’ s degrees and doctoral degrees in systems
engineering. An increasing
number of universities are offering undergraduate degrees in
systems engineering as
well.
The recognition of systems engineering as a profession has led
to the formation of
a professional society, the International Council on Systems
Engineering (INCOSE),
one of whose primary objectives is the promotion of systems
engineering, and the
recognition of systems engineering as a professional career.
Career Choices
Systems engineers are highly sought after because their skills
complement those in
other fi elds and often serve as the “ glue ” to bring new ideas
to fruition. However, career
87. choices and the related educational needs for those choices is
complex, especially when
the role and responsibilities of a systems engineer is poorly
understood.
Four potential career directions are shown in Figure 1.1 : fi
nancial, management,
technical, and systems engineering. There are varying degrees
of overlap between them
despite the symmetry shown in the fi gure. The systems
engineer focuses on the whole
system product, leading and working with many diverse
technical team members, fol-
lowing the systems engineering development cycle, conducting
studies of alternatives,
and managing the system interfaces. The systems engineer
generally matures in the
fi eld after a technical undergraduate degree with work
experience and a master of
science degree in systems engineering, with an increasing
responsibility of successively
larger projects, eventually serving as the chief or lead systems
engineer for a major
systems, or systems - of - systems development. Note the
overlap and need to understand
the content and roles of the technical specialists and to
coordinate with the program
manager (PM).
The project manager or PM, often with a technical or business
background, is
responsible for interfacing with the customer and for defi ning
the work, developing
the plans, monitoring and controlling the project progress, and
delivering the fi nished
output to the customer. The PM often learns from on the job
88. training (OJT) with
c01.indd 13c01.indd 13 2/8/2011 11:04:29 AM2/8/2011
11:04:29 AM
14 SYSTEMS ENGINEERING AND THE WORLD OF
MODERN SYSTEMS
projects of increasing size and importance, enhancing the
toolset available with a master
of science degree in technical/program management. While not
exclusively true,
the chief executive offi cer (CEO) frequently originates from
the ranks of the organiza-
tion ’ s PMs.
The fi nancial or business career path that ultimately could lead
to a chief
fi nancial offi cer (CFO) position usually includes business
undergraduate and master of
business administration (MBA) degrees. Individuals progress
through their careers with
various horizontal and vertical moves, often with specialization
in the fi eld. There is
an overlap in skill and knowledge with the PM in areas of
contract and fi nance
management.
Many early careers start with a technical undergraduate degree
in engineering,
science or information technology. The technical specialist
makes contributions as part
of a team in the area of their primary knowledge, honing skills
and experience to
89. develop and test individual components or algorithms that are
part of a larger system.
Contributions are made project to project over time, and
recognition is gained from
innovative, timely, and quality workmanship. Technical
specialists need to continue to
learn about their fi eld and to stay current in order to be
employable compared to the
next generation of college graduates. Often advanced degrees
(MS and PhDs) are
acquired to enhance knowledge, capability, and recognition, and
job responsibilities
can lead to positions such as lead engineer, lead scientist, or
chief technology offi cer
(CTO) in an organization. The broader minded or experienced
specialist often considers
a career in systems engineering.
Figure 1.1. Career opportunities and growth.
CFO
CFO
MBA
BSOne must keep fresh in the Developing fiscal skills and tools
CTO
BS MS OJT
Financial
technical field to avoid obsolescence through horizontal and
lateral transitions