Downloaded 29 times
![Type of equipment used General guideline: surface cutting recommenda-
with our diamond blades tion to bond. Do not use as an absolute. Select
from cutting application, locate bond then refer to
the index on next page. Choose blade from bond
Hand Held Grinder column to match bond from the list below.
Bond Code:
1. = Super Soft
Circular Hand Saw 2. = Soft
3. = Medium
4. = Hard
Handheld High Speed Saw
W. = Wood
S. = Speciality Blades
cutting Application bond to Use
Tile Saw
Asphalt . . . . . . . . . . . . . . . 4
Block, Heavy Wt. [36#] . . . . . . . 3
Block, Light Wt. [23#] . . . . . . . . 4
Bluestone . . . . . . . . . . . . . . 2
Brick Saw Brick . . . . . . . . . . . . . . . . 3
Cast Iron Pipe. . . . . . . . . . . . 1
Chattahoochee . . . . . . . . . . . 1&2
Clay Pavers . . . . . . . . . . . . . 3
Walk Behind Saw Concrete, Cured . . . . . . . . . . 2
Concrete, Green . . . . . . . . . . 4
Concrete Pavers . . . . . . . . . . 3
Concrete Pipe. . . . . . . . . . . . 3
Rail Saw Corian® . . . . . . . . . . . . . . . S
Cultured Marble. . . . . . . . . . . S
Ductile Iron . . . . . . . . . . . . . 1
Fiberglass . . . . . . . . . . . . . . S
Floor Grinder Fieldstone. . . . . . . . . . . . . . 2
Flagstone . . . . . . . . . . . . . . 2
Flint . . . . . . . . . . . . . . . . . 4
General Purpose . . . . . . . . . . 3
Glass . . . . . . . . . . . . . . . . S
Granite . . . . . . . . . . . . . . . 2
Core Driller
Hard Stone . . . . . . . . . . . . . 3
We manufacture all our diamond tools and blades to the highest Limestone (dense) . . . . . . . . . 1&2
specifications. Our factories are ISO Certified 9001 & 9002. Limestone (soft). . . . . . . . . . . 3&4
Marble . . . . . . . . . . . . . . . 2
Masonry. . . . . . . . . . . . . . . 2&3
Safety: PVC . . . . . . . . . . . . . . . . . GA Turbo
Always use blades per manufacturer’s equipment Quarry Stone [soft] . . . . . . . . . 2&3
recommendations. Never operate equipment without Rebar . . . . . . . . . . . . . . . . 1&2
blade guard. Reinforced Concrete . . . . . . . . 2
Do not exceed maximum RPM safe speed. River Rock . . . . . . . . . . . . . 1&2
Use safety equipment: OSHA required safety glasses Roots . . . . . . . . . . . . . . . . 3
Sandstone . . . . . . . . . . . . . 3&4
and hearing protection. Slate . . . . . . . . . . . . . . . . 2&3
Use blades in compliance with ANSI Code B7.1, Stone, Natural . . . . . . . . . . . 2
B7.5, and OSHA requirement 1910.215. Tarmac . . . . . . . . . . . . . . . 3
Terra Cotta . . . . . . . . . . . . . 3&4
All specifications subject to change without notice. Tile, Ceramic . . . . . . . . . . . . 2
Tile, Roof . . . . . . . . . . . . . . 3&4
VCP . . . . . . . . . . . . . . . . . GA Turbo
© Copyright 2009 DBD-Marketing
Wood . . . . . . . . . . . . . . . . W
HL/GRP Design
2 CALL FOR QUANTITY DISCOUNTS](https://image.slidesharecdn.com/2009ndcatalog-100415033459-phpapp02/85/Diamond-Tool-Catalog-2-320.jpg)
![TERMS
INDEX
iteM bond pAge iteM bond pAge iteM bond pAge
ACCESSORIES, CORERIG . . . . . . . 22 EARLY ENTRY BLADES . . . . . . . . . 12 NO DUST . . . . . . . . . . . . . . . . 34
ADAPTERS . . . . . . . . . . . . . . . 22 ENELFLEX - PADS . . . . . . . . . . . 30 PADS-STI . . . . . . . . . . . . . . . . 46
AGGREGATE MAP . . . . . . . . . . . 14 ENGINEERED STONE BLADE . . . . . 33 PADS-WORKMASTER . . . . . . . . . 45
AIR POLISHER . . . . . . . . . . . . . 27 ENHANDPAD . . . . . . . . . . . . . . 30 PADS, POLISHING . . . . . . . . . . . 27-30
AMERIPOLISH. . . . . . . . . . . . . . 36-38 EPTWIST . . . . . . . . . . . . . . . . 32 PATRIOT . . . . . . . . . . . . . . . . . 39
ASPHALT BLADES . . . . . . . . . . . 11 ETORANGE15 . . . . . . . . . . . . . 3 9 PIONEER ECLIPSE . . . . . . . . . . . 43
ASPHCER . . . . . . . . . . . . . . . 4 11 FHBLKMAGIC - PADS. . . . . . . . . . 28 POWER SCREW DRIVER . . . . . . . . 33
CARBIDE BLADES . . . . . . . . . . . 35 FHTITAN . . . . . . . . . . . . . . . . 1 4 PRESTRESSED BLADES . . . . . . . . 12
CEREECUT . . . . . . . . . . . . . 1-4 12 FLOOR, CONCRETE SUPPLY. . . . . . 36-46 PRO1CC . . . . . . . . . . . . . . . . 2 13
CHASPH . . . . . . . . . . . . . . . . 4 11 FX . . . . . . . . . . . . . . . . . . 1-4 14 PRO2CC . . . . . . . . . . . . . . . . 3 13
CHCOREBIT . . . . . . . . . . . . . . 3 21 GACNCDUO . . . . . . . . . . . . . 2-4 9 PRO3ASPH . . . . . . . . . . . . . . 4 13
CHCOREDRILL . . . . . . . . . . . . . 32 GACOMBO12 . . . . . . . . . . . . 2/3 5/9 PRO4AOC . . . . . . . . . . . . . . . 3 13
CHDRYCOREBIT . . . . . . . . . . . 3 20 GASANDTP . . . . . . . . . . . . . . 2 19 PROFILE CHART . . . . . . . . . . . . 31
CHELECTROSEG . . . . . . . . . . . 4 17 GASANDTRIPTP. . . . . . . . . . . . 2 19 PROFILE WHEELS . . . . . . . . . . . 31
CHELSLOT . . . . . . . . . . . . . . 4 17 GATSEG12 . . . . . . . . . . . . . . 2 5 PROTECTOR, CONCRETE . . . . . . . 42
CHFANCUP . . . . . . . . . . . . . . 2 25 GATSEG12 . . . . . . . . . . . . . . 2 7 REDUCERS . . . . . . . . . . . . . . . 22
CHGRAN . . . . . . . . . . . . . . . 1 4/6 GATURBO12 . . . . . . . . . . . . . 3 3/7 RENEGADE BLADES . . . . . . . . . . 35
CHGRANQUAD . . . . . . . . . . . . 1 4 GBTP.250 . . . . . . . . . . . . . . . 3 19 RESCUE BLADE. . . . . . . . . . . . . 17
CHSAMURAI . . . . . . . . . . . . . 3 4 GEOTECH ROUTER . . . . . . . . . . . 31 ROOT . . . . . . . . . . . . . . . . C3 17
CHSUPERG . . . . . . . . . . . . . 2-4 10 GGSEG15 . . . . . . . . . . . . . . . 3 5 SEGPLATE, REP SEGS . . . . . . . . 2 26
CHSUPERGR . . . . . . . . . . . . 2-4 10 GGSEG15 . . . . . . . . . . . . . . . 3 8 SHAPING WHEELS . . . . . . . . . . . 31
CHTLSEC . . . . . . . . . . . . . . . 2 16 GGTURBO15 . . . . . . . . . . . . . 3 3 SHCNCSAND . . . . . . . . . . . . 1-3 15
CHTORNADO . . . . . . . . . . . . . 2 4/6 GTBACKPAD . . . . . . . . . . . . . . 27 SHCOREP . . . . . . . . . . . . . . . 3 21
CHTSEG12 . . . . . . . . . . . . . . 3 7 GTCRACK . . . . . . . . . . . . . . . 2 18 SHCOREPP . . . . . . . . . . . . . . 3 21
CLEANER, CONCRETE . . . . . . . . . 42 GTCROWN . . . . . . . . . . . . . 2-3 23 SHCOREPPF . . . . . . . . . . . . . 3 21
CNCGRANITE . . . . . . . . . . . . . 2 15 GTCUP . . . . . . . . . . . . . . . . 2 24 SHCRACK . . . . . . . . . . . . . . . 2 18
CNCRINGSAW . . . . . . . . . . . . 2 17 GTCUPSWIRL . . . . . . . . . . . . . 2 24 SHCRACKV . . . . . . . . . . . . . . 2 18
COLOR CHARTS . . . . . . . . . . . . 37-40 GTCUPSWIRL . . . . . . . . . . . . . 2 24 SHCROWN . . . . . . . . . . . . . 2-3 23
CORE BITS . . . . . . . . . . . . . . . 20-22 GTLION . . . . . . . . . . . . . . . . 1 10 SHCUP . . . . . . . . . . . . . . . . 2 24
CORE DRILL RIGS . . . . . . . . . . . 22 GTRINGSAW . . . . . . . . . . . . . 3 17 SHDRYCOREBIT . . . . . . . . . . . 3 20
CORERIG PLATE . . . . . . . . . . . . 22 GTTURBOCC . . . . . . . . . . . . . 2 24 SHDUCTILE . . . . . . . . . . . . . . 1 10
CRACK CHASERS . . . . . . . . . . . 18 HKALUMBACKPAD . . . . . . . . . . . 27 SHESLGS . . . . . . . . . . . . . . . . 33
CROWN BITS . . . . . . . . . . . . . . 23 HKASPH10 . . . . . . . . . . . . . . 4 11 SHESTURBO . . . . . . . . . . . . . . 33
CUP WHEELS . . . . . . . . . . . . . . 24-26 HKCONCDRY - PADS . . . . . . . . . . 29 SHGREEN . . . . . . . . . . . . . . . 4 11
DENSIFIER, CONCRETE . . . . . . . . 42 HKCONCDRYT - PADS . . . . . . . . . 29 SHHOTTLS . . . . . . . . . . . . . . 2 16
DIAMOND PAD-WORKMASTER . . . . 45 HKCRYSTALCUP . . . . . . . . . . . 2 26 SHHOTTSEGCUP . . . . . . . . . . . 2 25
DIAMOND WHEEL-STI . . . . . . . . . 46 HKDRYFLEX - PADS . . . . . . . . . . 29 SHHOTTURBOCC . . . . . . . . . . . 2 25
DIYEUROSEG10. . . . . . . . . . . . 3 5 HKECFLEX - PADS . . . . . . . . . . . 28 SHPRESTRESSED . . . . . . . . . 1-4 12
DIYEUROTURBO10 . . . . . . . . . . 3 3 HKFINGERBIT . . . . . . . . . . . . . . 32 SHTSEG15 . . . . . . . . . . . . . . 1 7
DIYSEGPB10 . . . . . . . . . . . . . 3 8 HKLTEARDROP . . . . . . . . . . . . 2 26 SHTURBOCC . . . . . . . . . . . . . 2 25
DIYSEGPB12 . . . . . . . . . . . . . 3 8 HKNEOPAD . . . . . . . . . . . . . . . 28 SHVANEBB15 . . . . . . . . . . . . . 3 9
DIYSEGRB. . . . . . . . . . . . . . . 3 8 HKPCDWHEEL . . . . . . . . . . . . 2 26 SHWAVE . . . . . . . . . . . . . . . . 1 3
DIYTPS . . . . . . . . . . . . . . . . 2 19 HKRIDGIDBACKPAD . . . . . . . . . . 27 SSSEGPLATE . . . . . . . . . . . . . . 26
DK CORERIGS . . . . . . . . . . . . . 22 HKSHINEPAD . . . . . . . . . . . . . . 28 STI . . . . . . . . . . . . . . . . . . . . 46
DMWEDGECUT . . . . . . . . . . . . 1 16 HKUCUP . . . . . . . . . . . . . . . 2 25 STJSLOT . . . . . . . . . . . . . . . 1 16
DRUM WHEEL. . . . . . . . . . . . . . 32/33 IDLGS . . . . . . . . . . . . . . . . . 2 15 STTLS . . . . . . . . . . . . . . . . . 1 16
DSLAMPO . . . . . . . . . . . . . . . 2 15 INTERNATIONAL BLADES . . . . . . . 34 SUPERG . . . . . . . . . . . . . . . 2-4 10
DSTWCORE . . . . . . . . . . . . . 2-3 23 JOTSEGPLATE . . . . . . . . . . . . . 26 TILE BLADES . . . . . . . . . . . . . . 16
DSWAVE-S . . . . . . . . . . . . . . 1 4 KEMIKO . . . . . . . . . . . . . . . . . 40/41 TUCK POINTERS . . . . . . . . . . . . 19
DTBRCOREBIT . . . . . . . . . . . 2-3 23 KFBACKPAD . . . . . . . . . . . . . . 27 VAC PUMP . . . . . . . . . . . . . . . 22
DTROSEX - PADS . . . . . . . . . . . . 29 KWIK DRIVE . . . . . . . . . . . . . . . 33 WERKMASTER . . . . . . . . . . . . . 44/45
DTTURBOCAT . . . . . . . . . . . . . . 30 LKVBCOREBIT . . . . . . . . . . . 2-3 23 WERKMASTER . . . . . . . . . . . . . 44/45
DTTYPHOON - PADS . . . . . . . . . . 30 LYTHIC . . . . . . . . . . . . . . . . . 42 ZERO TOLERANCE . . . . . . . . . . . 32
DUST SHROUD . . . . . . . . . . . . . 24 METAL CUTTING BLADES . . . . . . . 35
Recommended Maximum
Diameter Operating Safe
Speed [RPM] Speed [RPM]
Hours Of Operation: 8:00 am to 5:00 pm EST.
ades 4” 9,050 15,000
ing Depth 4.5” 8,050 13,300 Freight Policy: FOB warehouse, no freight charges on orders
5” 5” 7,250 12,000
7” 6” 6,050 10,150 over $1500.00 within continental USA.
8” 7” 5,180 8,730
8” 4,536 7,640 Return Policy: All returns must have a RA number (Return
ades 9” 4,030 6,790
10” 3,625 6,115 Authorization) and subject to a 15%
1 3/4” 12” 3,020 5,095
2
2
1/4”
3/4”
12” HS [High Speed] 6,300 restocking fee.
14” 2,590 4,365
3 1/4”
3 3/4” 14” HS [High Speed] 5,400 Limited Warranty: All products are guaranteed against defects
16” 2,265 3,820
lades
16” HS [High Speed] 4,800 in material and workmanship for 1 year. The
18” 2,016 3,395
1”
20” 1,810 3,055 limited warranty does not cover improper or
1 1/4” 24” 1,510 2,550
1 1/2” 26” 1,395 2,350 negligent use.
2 1/2” 28” 1,295 2,185
3” 30” 1,210 2,040 Warranted products will be repaired or
32” 1,135 1,910
36” 1,010 1,700 replaced at the option of the company.
42” 864 1,455
48” 756 1,275
CALL FOR QUANTITY DISCOUNTS 47](https://image.slidesharecdn.com/2009ndcatalog-100415033459-phpapp02/85/Diamond-Tool-Catalog-47-320.jpg)
Uploaded byNational Diamond
Diamond Tool Catalog
The document provides a product catalog for diamond cutting blades and tools from National Diamond, emphasizing their expertise in the industry since 1988. It includes specific recommendations for bond selection based on materials and applications, along with safety guidelines for usage. Various blade specifications, including unique features and performance characteristics, are detailed to assist in selecting suitable tools for different cutting tasks.
Diamond Tool Catalog
- 1. EX CIT ING NE W PR OD UC TS INS IDE ! “World Leader In Diamond Cutting Blades & Tools” 2009 800-659-5843 RO DUCTS CATALOG P ALITY www.national-diamond.com Diamond Blades & Tools QU Est. Since 1988
- 2. Type of equipmentused General guideline: surface cutting recommenda- with our diamond blades tion to bond. Do not use as an absolute. Select from cutting application, locate bond then refer to the index on next page. Choose blade from bond Hand Held Grinder column to match bond from the list below. Bond Code: 1. = Super Soft Circular Hand Saw 2. = Soft 3. = Medium 4. = Hard Handheld High Speed Saw W. = Wood S. = Speciality Blades cutting Application bond to Use Tile Saw Asphalt . . . . . . . . . . . . . . . 4 Block, Heavy Wt. [36#] . . . . . . . 3 Block, Light Wt. [23#] . . . . . . . . 4 Bluestone . . . . . . . . . . . . . . 2 Brick Saw Brick . . . . . . . . . . . . . . . . 3 Cast Iron Pipe. . . . . . . . . . . . 1 Chattahoochee . . . . . . . . . . . 1&2 Clay Pavers . . . . . . . . . . . . . 3 Walk Behind Saw Concrete, Cured . . . . . . . . . . 2 Concrete, Green . . . . . . . . . . 4 Concrete Pavers . . . . . . . . . . 3 Concrete Pipe. . . . . . . . . . . . 3 Rail Saw Corian® . . . . . . . . . . . . . . . S Cultured Marble. . . . . . . . . . . S Ductile Iron . . . . . . . . . . . . . 1 Fiberglass . . . . . . . . . . . . . . S Floor Grinder Fieldstone. . . . . . . . . . . . . . 2 Flagstone . . . . . . . . . . . . . . 2 Flint . . . . . . . . . . . . . . . . . 4 General Purpose . . . . . . . . . . 3 Glass . . . . . . . . . . . . . . . . S Granite . . . . . . . . . . . . . . . 2 Core Driller Hard Stone . . . . . . . . . . . . . 3 We manufacture all our diamond tools and blades to the highest Limestone (dense) . . . . . . . . . 1&2 specifications. Our factories are ISO Certified 9001 & 9002. Limestone (soft). . . . . . . . . . . 3&4 Marble . . . . . . . . . . . . . . . 2 Masonry. . . . . . . . . . . . . . . 2&3 Safety: PVC . . . . . . . . . . . . . . . . . GA Turbo Always use blades per manufacturer’s equipment Quarry Stone [soft] . . . . . . . . . 2&3 recommendations. Never operate equipment without Rebar . . . . . . . . . . . . . . . . 1&2 blade guard. Reinforced Concrete . . . . . . . . 2 Do not exceed maximum RPM safe speed. River Rock . . . . . . . . . . . . . 1&2 Use safety equipment: OSHA required safety glasses Roots . . . . . . . . . . . . . . . . 3 Sandstone . . . . . . . . . . . . . 3&4 and hearing protection. Slate . . . . . . . . . . . . . . . . 2&3 Use blades in compliance with ANSI Code B7.1, Stone, Natural . . . . . . . . . . . 2 B7.5, and OSHA requirement 1910.215. Tarmac . . . . . . . . . . . . . . . 3 Terra Cotta . . . . . . . . . . . . . 3&4 All specifications subject to change without notice. Tile, Ceramic . . . . . . . . . . . . 2 Tile, Roof . . . . . . . . . . . . . . 3&4 VCP . . . . . . . . . . . . . . . . . GA Turbo © Copyright 2009 DBD-Marketing Wood . . . . . . . . . . . . . . . . W HL/GRP Design 2 CALL FOR QUANTITY DISCOUNTS
- 3. SMALL DIAMATER TURBO BLADES 4” x .080” x 7/8”-5/8” 4diYeUrotUrbo10 EURO TURBO 4.5” x .080” x 7/8”-5/8” 4.5diYeUrotUrbo10 These diamond blades have a unique cold pressed 5” x .080” x 7/8”-5/8” 5diYeUrotUrbo10 6” x .080” x 7/8”-5/8” 6diYeUrotUrbo10 castellated rim which provides fast chip free cutting. 7” x .095” x DM-5/8” 7diYeUrotUrbo10 Cuts brick, block, concrete, bluestone, flagstone, 8” x .095” x DM-5/8” 8diYeUrotUrbo10 granite, roof tile and other hard masonry materials. 9” x .095” x 7/8”-5/8” 9diYeUrotUrbo10 10mm Rim Height Use wet or dry. 10” x .095” x 7/8”-5/8” 10diYeUrotUrbo10 HS W/D 3 4” x .080” x 7/8”-5/8” 4gAtUrbo12 GRAPE APE PRO 4.5” x .080” x 7/8”-5/8” 4.5gAtUrbo12 These premium diamond blades have a unique cold 5” x .080” x 7/8”-5/8” 5gAtUrbo12 7” x .095” x DM-5/8” 7gAtUrbo12 pressed castellated rim which provides fast chip free 8” x .095” x DM-5/8” 8gAtUrbo12 cutting. 9” x .095” x 7/8”-5/8” 9gAtUrbo12 Cuts brick, block, concrete, bluestone, flagstone, 10” x .095” x 7/8”-5/8” 10gAtUrbo12 granite, roof tile and other hard masonry materials. 12mm Rim Height Use wet or dry. HS W/D 3 12 mm Rim Height 4” x .080” x 7/8”-5/8” 4ggtUrbo15 GREEN GIANT TURBO 4.5” x .080” x 7/8”-5/8” 4.5ggtUrbo15 These NEW 15mm rim height diamond blades provide 5” x .080” x 7/8”-5/8” 5ggtUrbo15 6” x .080” x 7/8”-5/8” 6ggtUrbo15 extra long life. They also have a unique cold pressed 7” x .095” x DM-5/8” 7ggtUrbo15 castellated rim which provides fast chip free cutting. 8” x .095” x DM-5/8” 8ggtUrbo15 Cuts brick, block, concrete, bluestone, flagstone, 10” x .095” x 7/8”-5/8” 10ggtUrbo15 granite, roof tile and other hard masonry materials. 15mm Rim Height Use wet or dry. HS W/D 3 15 mm Rim Height 4” x .095” x 7/8”-5/8” 4ShwAVe SHOCK WAvE 4.5” x .095” x 7/8”-5/8” 4.5ShwAVe Our SHOCK WAVE provides that extra speed demanded 5” x .095” x 7/8”-5/8” 5ShwAVe 6” x .095” x 7/8”-5/8” 6ShwAVe by professional users. Also the zipper style segments 7” x .095” x DM-5/8” 7ShwAVe provide extremely smooth cuts. The performance and 8” x .095” x 7/8”-5/8” 8ShwAVe life on these blades are outstanding. Try one today. Use 9” x .095” x 7/8”-5/8” 9ShwAVe this diamond blade for cutting: granite, marble, brick, block, tile, concrete & other masonry materials. 7mm Rim Height Use wet or dry. HS W/D 1 = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 3
- 4. SMALL DIAMATER TURBO BLADES POWER WAvE 4” x .080” x 7/8”-5/8” 4dSwAVe-S 4.5” x .080” x 7/8”-5/8” 4.5dSwAVe-S Our Supreme POWERWAVE will provide exceptional speed, 5” x .080” x 7/8”-5/8” 5dSwAVe-S demanded by professionals. The zipper segments are loaded with 30/40 grit diamonds for extremely fast smooth cuts. 6” x .080” x 7/8”-5/8” 6dSwAVe-S The vented core allows water to power through the holes for 7” x .095” x DM-5/8” 7dSwAVe-S cool running and longer blade life. These long life blades are considered some of the best in the market today. Use this diamond blade for cutting: granite, marble, brick, block, tile, concrete & other masonry materials. 7mm Rim Height Use wet or dry. HS W/D 1 TITAN TURBO 4.5” x .080” x 7/8”-20mm 4.5fhtitAn 5” x .080” x 7/8”-20mm 5fhtitAn This precision made diamond blade is designed for an 7” x .095” x 7/8”-20mm 7fhtitAn extremely smooth surface finish and fast cutting. The cat claw drop segs and vented core keep this blade running cooler for extended blade life. The MBS 960 diamonds also assist in cutting efficiency and blade longevity. Cuts: granite, hard stone, cured concrete and similar surfaces. 10mm Rim Height Use wet or dry. HS W/D 1 SAMURAI GRAN 4” x .080” x 7/8”-5/8” 4chgrAnQUAd 4.5” x .080” x 7/8”-5/8” 4.5chgrAnQUAd We manufacture these self-propelled blades to meet 5” x .080” x 7/8”-5/8” 5chgrAnQUAd the demands of contractors looking for consistently 7” x .095” x DM-5/8” 7chgrAnQUAd good working tools. The wavy steel core assists in air 8” x .095” x DM-5/8” 8chgrAnQUAd circulation and reduces friction which prolongs blade 9” x .095” x 7/8”-5/8” 9chgrAn life and increases cutting speed. Cuts: granite, cured 10” x .095” x 7/8”-5/8” 10chgrAn concrete & other hard masonry materials. 10mm Rim Height Use wet or dry. HS W/D 1 SAMURAI CHARGER 4” x .080” x 7/8”-5/8” 4chSAMUrAi 4.5” x .080” x 7/8”-5/8” 4.5chSAMUrAi This blade is built for a consistent winning performance. 5” x .080” x 7/8”-5/8” 5chSAMUrAi The deep drop segments allow for core protection and 7” x .095” x DM-5/8” 7chSAMUrAi long core life. A special diamond bond is engineered into 8” x .095” x DM-5/8” 8chSAMUrAi the segments for fast cutting and long blade life. 9” x .095” x 7/8”-5/8” 9chSAMUrAi Cuts: granite, cured concrete, roof tile and other 10” x .095” x 7/8”-5/8” 10chSAMUrAi masonry materials. 10mm Rim Height Use wet or dry. HS W/D 3 TORNADO 4” x .080” x 7/8”-5/8” 4chtornAdo 4.5” x .080” x 7/8”-5/8” 4.5chtornAdo Fast and smooth, the deep drop segments allow for 5” x .080” x 7/8”-5/8” 5chtornAdo core protection and long core life. Special diamond grit 7” x .095” x DM-5/8” 7chtornAdo & bond is engineered into the segments for fast cutting 10” x .095” x 7/8”-5/8” 10chtornAdo and long blade life. Cuts: granite, cured concrete, roof tile and other masonry materials. 10mm Rim Height w/ Drop Segs Use wet or dry. HS W/D 2 4 CALL FOR QUANTITY DISCOUNTS
- 5. SMALL DIAMATER SEGMENTED BLADES 4” x .080” x 7/8”-5/8” 4diYeUroSeg10 EURO SEG 4.5” x .080” x 7/8”-5/8” 4.5diYeUroSeg10 Our .395 segmented height (10mm) Supreme Blades 5” x .080” x 7/8”-5/8” 5diYeUroSeg10 6” x .080” x 7/8”-5/8” 6diYeUroSeg10 are among the finest in the market! Outlasting most of 7” x .095” x DM-5/8” 7diYeUroSeg10 the competition by 30 to 40%. A heat treated steel core 8” x .095” x DM-5/8” 8diYeUroSeg10 provides extreme blade strength for deep cuts. Perfect 9” x .095” x 7/8”-5/8” 9diYeUroSeg10 for the contractor who wants quality at a reasonable 10” x .095” x 7/8”-5/8” 10diYeUroSeg10 price. Try these today! Medium bond, for general purpose brick, block & concrete. 10mm Segment Height Use wet or dry. HS W/D 3 4” x .080” x 7/8”-5/8” 4gAcoMbo12 GRAPE APE 4.5” x .080” x 7/8”-5/8” 4.5gAcoMbo12 This laser welded segmented blade is for the contractor 5” x .080” x 7/8”-5/8” 5gAcoMbo12 who has the most rugged and demanding job of going 7” x .080” x DM-5/8” 7gAcoMbo12 8” x .095” x DM-5/8” 8gAcoMbo12 through cured concrete or reinforced concrete with rebar. 9” x .095” x DM-5/8” 9gAcoMbo12 Made with G.E. best 30/40 mesh MBS 960 grade diamonds. 10” x .110” x DM-5/8” 10gAcoMbo12 The GRAPE APE delivers outstanding performance at an affordable cost. Try this recipe of diamonds and you’ll know why this is #1. For General purpose, concrete, 12 mm Segment Height brick, block and similar masonry surfaces. 12mm Segment Height Use wet or dry. HS W/D 2/3 4” x .080” x 7/8”-5/8” 4ggSeg15 GREEN GIANT 4.5” x .080” x 7/8”-5/8” 4.5ggSeg15 The new GREEN GIANT diamond blade with it’s 15mm 5” x .080” x 7/8”-5/8” 5ggSeg15 6” x .095” x 7/8”-5/8” 6ggSeg15 jumbo segment height was designed to provide long 7” x .095” x DM-5/8” 7ggSeg15 blade life and fast cuts. Geared toward the contractor 8” x .095” x DM-5/8” 8ggSeg15 that is looking for functional value at a economical price. 10” x .095” x 7/8”-5/8” 10ggSeg15 This medium bond blade is perfect for cutting: General purpose masonry, brick, block and concrete. 15mm Segment Height Use wet or dry. 15 mm Segment Height HS W/D 3 4” x .080” x 7/8”-5/8” 4gAtSeg12 T-SEG PRO12 4.5” x .080” x 7/8”-5/8” 4.5gAtSeg12 Our Supreme Grape Ape T-SEG PRO12 turbo segmented 5” x .080” x 7/8”-5/8” 5gAtSeg12 design has been copied by many other companies but none 7” x .095” x DM-5/8” 7gAtSeg12 8” x .095” x DM-5/8” 8gAtSeg12 can master the supreme quality of this blade. The lightning 9” x .095” x 7/8”-5/8” 9gAtSeg12 speed of a turbo with the life of a segmented blade is sure 10” x .095” x 7/8”-5/8” 10gAtSeg12 to get the toughest jobs done with ease. Laser welded. Ideal for cured concrete, concrete pipe, pavers, block, clay brick with iron spots and much more. 12 mm Segment Height 12mm Segment Height Use wet or dry. HS W/D 2 = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 5
- 6. HIGH SPEED TURBO / T-SEG BLADES SAMURAI GRAN 12” x .125” x 1”-20mm 12chgrAn 14” x .125” x 1”-20mm 14chgrAn We manufacture this self-propelled blade to meet the demand of contractors looking for consistently good working tools. The wavy steel core assists in air circulation and reduces friction which prolongs blade life and increases cutting speed. Cuts: granite, cured concrete & other hard masonry materials. 10mm Rim Height Use wet or dry. HS W/D 1 TORNADO 12” x .110” x 1”-20mm 12chtornAdo 14” x .110” x 1”-20mm 14chtornAdo Fast and smooth, the deep drop segments allow for core protection and long core life. Special diamond grit & bond is engineered into the segments for fast cutting and long blade life. Cuts: granite, cured concrete, roof tile and other masonry materials. 10mm Rim Height w/ Drop Segs Use wet or dry. HS W/D 2 6 CALL FOR QUANTITY DISCOUNTS
- 7. HIGH SPEED TURBO / T-SEG BLADES 12” x .125” x 1”-20mm 12gAtUrbo12 GRAPE APE PRO 14” x .125” x 1”-20mm 14gAtUrbo12 These diamond blades have a unique cold pressed castellated rim which provides fast chip free cutting. Cuts brick, block, concrete, bluestone, flagstone, granite, roof tile and other hard masonry materials. 12mm Rim Height Use wet or dry. HS W/D 3 12 mm Segment Height 12” x .125” x 1”-20mm 12chtSeg12 PRO MASTER T-SEG 14” x .125” x 1”-20mm 14chtSeg12 This turbo/segmented design is engineered to meet the 14” x .125” x 20mm 14chtSeg12-20 14” x .140” x 1”-20mm 14chtSeg10.140 challenges of all general purpose cutting conditions. 16” x .125” x 1”-20mm 16chtSeg12 Heat treated steel core provides extreme blade strength in deep cuts. This blade is a true work horse for excellent cutting speed and great life. Medium bond, for general purpose brick, block & concrete. 12mm Segment Height Use wet or dry. 12 mm Segment Height HS W/D 3 12” x .125” x 1”-20mm 12gAtSeg12 T-SEG PRO12 12” x .125” x 20mm 12gAtSeg12-20 Our Supreme Grape Ape T-SEG PRO12 turbo segmented 14” x .125” x 1”-20mm 14gAtSeg12 14” x .125” x 20mm 14gAtSeg12-20 design has been copied by many other companies but none can master the supreme quality of this blade. The lightning speed of a turbo with the life of a segmented blade is sure to get the toughest jobs done with ease. Laser welded. Ideal for cured concrete, concrete pipe, 12 mm pavers, block, clay brick with iron spots and much, Segment Height much more. 12mm Segment Height Use wet or dry. HS W/D 2 12” x .125” x 1”-20mm 12ShtSeg15 T-SEG SIGNATURE15 14” x .125” x 20mm 12ShtSeg15-20 We designed this blade with a double segment height 12” x .125” x 1”-20mm 14ShtSeg15 14” x .125” x 20mm 14ShtSeg15-20 for the contractor who demands longer blade life. 16” x .125” x 1”-20mm 16ShtSeg15 Besides the longer life there is also the advantage of 18” x .125” x 1”-20mm 18ShtSeg15 saving time with less blade changes on your equipment. 20” x .125” x 1”-20mm 20ShtSeg15 The segments are laser welded with a super soft bond 12” x .125” x 1”-20mm 12ShtSeg15c* for cutting: Cured concrete, reinforced concrete, 12” x .125” x 20mm 12ShtSeg15c20* rebar, concrete pipe, rigid concrete pipe (RCP) and 14” x .125” x 1”-20mm 14ShtSeg15c* refractory brick. 14” x .125” x 1”-20mm 14ShtSeg15c20* 15mm Segment Height Use wet or dry. 16” x .125” x 1”-20mm 16ShtSeg15c* HS W/D 1 Signature 18” x .125” x 1”-20mm 18ShtSeg15c* Series 15 mm Segment Height *Clam shell packed = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 7
- 8. HIGH SPEED SEGMENTED BLADES RED BULL 4” x .080” x 7/8”-5/8” 4diYSegrb 4.5” x .080” x 7/8”-5/8” 4.5diYSegrb Our contractor series, RED BULL is the perfect blade for 7” x .095” x DM-5/8” 7diYSegrb those jobs that need low up front cost, but must meet 10” x .095” x 7/8”-5/8” 10diYSegrb the fast paced demands of getting the job done. A solid 12” x .125” x 1”-20mm 12diYSegrb core winner. Try one today! 14” x .125” x 1”-20mm 14diYSegrb Cuts: general purpose, brick, block, masonry 7mm Segment Height Use wet or dry. HS W/D 3 TOUGH-CUT PRO 12” x .125” x 1”-20mm 12diYSegpb10 12” x .125” x 20mm 12diYSegpb10-20 This is our super duty work horse, ideal for cutting all 14” x .125” x 1”-20mm 14diYSegpb10 types of surfaces. Perfect for rental yards and contractors 14” x .125” x 20mm 14diYSegpb10-20 who need low up front costs, fast cutting speed with 16” x .125” x 1”-20mm 16diYSegpb10 medium blade life. The PB10 is by far our most popular 20” x .125” x 1”-20mm 20diYSegpb10 blade. Don’t take our word for it. Find out for yourself just what makes this our most popular item. Medium bond, for general purpose masonry, brick, block & light duty cured concrete. 10mm Segment Height Use wet or dry. HS W/D 3 POWER-CUT12 12” x .125” x 1”-20mm 12diYSegpb12 12” x .125” x 20mm 12diYSegpb12-20 This new blade is a super duty work horse with 12mm 14” x .125” x 1”-20mm 14diYSegpb12 high segments that provide longer life. Perfect for rental 14” x .125” x 20mm 14diYSegpb12-20 yards and contractors who need low up front costs, fast 18” x .125” x 1”-20mm 18diYSegpb12 cutting speed with medium blade life. The PB12 is an extremely popular blade. Don’t take our word for it. Try one today! Medium bond, for general purpose masonry, brick, block & light duty cured concrete. 12mm Segment Height HS W/D 3 Use wet or dry. 12 mm Segment Height GREEN GIANT 12” x .125” x 1”-20mm 12ggSeg15 12” x .125” x 20mm 12ggSeg15-20 The new GREEN GIANT diamond blade with it’s 15mm 14” x .125” x 1”-20mm 14ggSeg15 jumbo segment height was designed to provide long 14” x .125” x 20mm 14ggSeg15-20 blade life and fast cuts. Geared toward the contractor 16” x .125” x 1”-20mm 16ggSeg15 that is looking for functional value at a economical price. 20” x .125” x 1”-20mm 20ggSeg15 This medium bond blade is perfect for cutting: General purpose masonry, brick, block and concrete. 15mm Segment Height Use wet or dry. HS W/D 3 15 mm Segment Height Signature Series Blue Ribbon winner in 2007 & 2008 at the World Of Concrete 8 CALL FOR QUANTITY DISCOUNTS
- 9. HIGH SPEED SEGMENTED BLADES 12” x .125” x 1”-20mm 12etorAnge15 ORANGE SLICE 12” x .125” x 20mm 12etorAnge15-20 The ORANGE SLICE is a remarkable diamond blade 14” x .125” x 1”-20mm 14etorAnge15 14” x .125” x 20mm 14etorAnge15-20 engineered with so many premium features that it truly give the longest life and fastest cutting speed. Segments are laser welded with Russian Cushion Cut Diamonds in the matrix. This produces sharper edges for faster cutting. Along with a jumbo 15mm high segment. And you will see why this awesome blade can’t be beat. 15 mm Segment Height Mount to a hand saw or bolt on to a walk behind saw. Try one today! Cuts: Concrete, brick, block and similar masonry materials. Signature 15mm Segment Height Use wet or dry. Series HS W/D 3 12” x .125” x 1”-20mm 12gAcoMbo12 GRAPE APE 12” x .125” x 20mm 12gAcoMbo12-20 This laser welded segmented blade is for the contractor 14” x .125” x 1”-20mm 14gAcoMbo12 who has the most rugged and demanding job of going 14” x .125” x 20mm 14gAcoMbo12-20 16” x .125” x 1”-20mm 16gAcoMbo12 through cured concrete or reinforced concrete with rebar. 16” x .125” x 20mm 16gAcoMbo12-20 Made with G.E. best 30/40 mesh MBS 960 grade diamonds. 20” x .135” x 1”-20mm 20gAcoMbo12 The GRAPE APE delivers outstanding performance at an affordable cost. Try this recipe of diamonds and you’ll know why this is #1. For General purpose, concrete, brick, block and similar masonry surfaces. 12 mm 12mm Segment Height Use wet or dry. Segment Height HS W/D 2/3 12” x .125” x 1”-20mm 12ShVAnebb15 HURRICANE SIGNATURE15 14” x .125” x 1”-20mm 14ShVAnebb15 The awesome cutting power of the new 15mm segment 20” x .125” x 1”-20mm 20ShVAnebb15 12” x .125” x 1”-20mm 12ShVAnebb15c height SHVANEBB15 blade provides fast cuts and lasts 12” x .125” x 20mm 12ShVAnebb15c20 twice as long as regular 7mm blades. The special vented 14” x .125” x 1”-20mm 14ShVAnebb15c core and wide gullets keep this blade running cooler and 14” x .125” x 20mm 14ShVAnebb15c20 also helps remove slurry for friction free cutting. Laser welded segments with a medium soft bond for cutting brick, block, masonry and other similar materials. 15mm Segment Height Use wet or dry. 15 mm Segment Height HS W/D 3 Signature Series 12” x .125” x 1”-20mm 12gAcncdUo MULTI-CUT CNC-DUO 14” x .125” x 1”-20mm 14gAcncdUo Computerized laser welded numerical controlled multi- cut diamond blade technology allows diamonds to be arrayed in optimal position allowing the blade to perform at peak efficiency. By far this blade is the most efficient diamond cutting blade in the market. This new high tech blade will normally achieve about 30-50% faster cutting and certainly twice the blade life of any blade now manufactured. Cuts: Hard concrete, concrete pavers, reinforced concrete, brick pavers, brick, block, asphalt & green concrete. 10mm Segment Height Use wet or dry. HS W/D 2/4 = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 9
- 10. HIGH SPEED MULTI-CUT BLADES SUPER SONIC - SUPREME 12” x .125” x 1”-20mm 12SUperg 12” x .125” x 1”-20mm 12SUperg20 NEW TECHNOLOGY: Cuts the widest variety of materials 14” x .125” x 1”-20mm 14SUperg in the market. This highly aggressive diamond blade is built 14” x .125” x 1”-20mm 14SUperg20 with a mixed variety of diamond grit sizes in the segments. 16” x .125” x 1”-20mm 16SUperg Drop segs along with a vented core also help this blade 18” x .125” x 1”-20mm 18SUperg drive through many surfaces with ease. Cuts: Cured 20” x .125” x 1”-20mm 20SUperg concrete, brick, block, concrete pipe, green concrete, pavers over sand, asphalt & asphalt over concrete. Use with hand held or tabletop saws. Signature 9/14mm Segmented Height Use wet or dry. Series HS W/D 2/4 SUPER SONIC 12” x .125” x 1”-20mm 12chSUperg 14” x .125” x 1”-20mm 14chSUperg This re-engineered multi use blade cuts a wide variety of surface materials. The very aggressive diamond blade is built with a mixed variety of diamond grit sizes in the segments. Drop segs along with a vented core also help this blade drive through many materials with ease. Cuts: Cured concrete, brick, block, concrete pipe, green concrete, pavers over sand, asphalt & asphalt over concrete. Use with hand held or tabletop saws. 9/14mm Segmented Height Use wet or dry. HS W/D 2/4 RED SUPER SONIC 12” x .125” x 1”-20mm 12chSUpergr 14” x .125” x 1”-20mm 14chSUpergr This new-design premium blade cuts a wide variety of surface materials. The highly aggressive diamond blade is built with a mixed variety of diamond grit sizes in the segments. Drop segs along with a vented core also help this blade drive through many surfaces with ease. Cuts: Cured concrete, brick, block, concrete pipe, green concrete, pavers over sand, asphalt & asphalt over concrete. Use with hand held or tabletop saws. 9/14mm Segment Height Use wet or dry. HS W/D 2/4 GT LION 4” x .080” x 7/8”-5/8” 4gtlion 4.5” x .080” x 7/8”-5/8” 4.5gtlion This Vacuum Brazed “LION” power blade cuts a 5” x .080” x 7/8”-5/8” 5gtlion wide variety of hard surfaces. The MBS950 surface 6” x .080” x 7/8”-5/8” 6gtlion set diamonds, give this blade the power needed for 7” x .095” x DM-5/8” 7gtlion aggressive cutting. Also built with a highly tensioned 8” x .095” x DM-5/8” 8gtlion steel .125 core for true track running and long life. 10” x .095” x 7/8”-5/8” 10gtlion Cuts: Ductile iron, cast iron, PVC, reinforced concrete, 12” x .125” x 1”-20mm 12gtlion reinforced concrete pipe, steel, wood. 14” x .125” x 1”-20mm 14gtlion THE ULTIMATE EMERGENCY RESCUE BLADE Signature Series Use wet or dry. HS W/D 1 IRON MAN SIGNATURE 12” x .125” x 1”-20mm 12ShdUctile 12” x .125” x 20mm 12ShdUctile-20 The awesome cutting power of our new IRON MAN 14” x .125” x 1”-20mm 14ShdUctile SIGNATURE will make you a believer in the Signature 14” x .125” x 20mm 14ShdUctile-20 blade series for nonstop day-in and day-out cutting. We 16” x .125” x 1”-20mm 16ShdUctile manufactured this laser welded blade with 50mm segment 16” x .125” x 20mm 16ShdUctile-20 lengths and utilized 960 grade diamonds with mesh mix of 40/50 and 50/60. These blades get the job done. Both sides of the blade are coated with diamonds concentrated in a swirl pattern, ideal for beveling. Cuts ductile pipe, cast iron pipe, ridged concrete pipe and cured concrete. Use wet or dry. HS W/D 1 10 CALL FOR QUANTITY DISCOUNTS
- 11. HIGH SPEED ASPHALT BLADES 7” x .095” x DM-5/8” 7ASphcer WILD CAT 8” x .095” x DM-5/8” 8ASphcer Our abrasive resistant “Carborundum” blade has absolutely 10” x .095” x 7/8”-5/8” 10ASphcer no diamonds in the matrix. This blade is impregnated with a 12” x .125” x 1”-20mm 12ASphcer special ceramic carbide grit, which brings a cost savings to 12” x .125” x 20mm 12ASphcer20 the contractor. Undercut protection is provided evenly through 14” x .125” x 1”-20mm 14ASphcer the gullets to prevent pinching or binding when cutting. A sure 14” x .125” x 20mm 14ASphcer20 winner when you are interested in up front costs. Cuts asphalt & 20” x .125” x 1”-20mm 20ASphcer green concrete, also use on roof tiles & light weight block. 10mm Segment Height Use wet or dry. HS W/D 4 7” & 8” have 8mm Segment Height 12” x .125” x 1”-20mm 12hkASph10 PANTHER 14” x .125” x 1”-20mm 14hkASph10 Our heavy duty contractor series, PANTHER is the perfect blade for those jobs that need low up front cost, but must meet the fast paced demands of getting the job done. Built with drop segments for undercut protection. Core thickness .125 inch. Cuts: Asphalt, green concrete, light weight block. 10mm Segment Height Use wet or dry. HS W/D 4 8” x .125” x 1”-20mm 8chASph CHEETAH-1 10” x .125” x 1”-20mm 10chASph The Cheetah-1 is an outstanding quality asphalt blade. 12” x .125” x 1”-20mm 12chASph 14” x .125” x 1”-20mm 14chASph This professional blade with its laser welded segments 16” x .125” x 1”-20mm 16chASph provides very accurate cutting. Features undercut 18” x .125” x 1”-20mm 18chASph protection, pin hole drive and high diamond content. 20” x .125” x 1”-20mm 20chASph Also ideal for walk behind saws as well! Cuts: asphalt, light weight block, green concrete, & other abrasive materials. 7mm Segment Height Use wet or dry. HS W/D 4 12” x .125” x 1”-20mm 12Shgreen THE HULK SIGNATURE 12” x .125” x 20mm 12Shgreen20 14” x .125” x 1”-20mm 14Shgreen We designed this blade for the contractor who needs 14” x .125” x 20mm 14Shgreen20 the best cutting tool in the industry. This laser welded 16” x .125” x 1”-20mm 16Shgreen segmented blade is perfect for low HP walk behind saws. 16” x .125” x 20mm 16Shgreen20 The unique feature of this blade is its undercut protection 18” x .125” x 1”-20mm 18Shgreen system with C3 carbide inserts. This blade cuts and clears 20” x .125” x 1”-20mm 20Shgreen 12” x .125” x 1”-20mm 12Shgreenc a cutting path in one motion. The hard bond is perfect for 12” x .125” x 20mm 12Shgreenc20 cutting asphalt, green concrete & light weight block. 14” x .125” x 1”-20mm 14Shgreenc 10mm Segment Height Use wet or dry. 14” x .125” x 20mm 14Shgreenc20 HS W/D 4 Signature Series = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 11
- 12. PROFESSIONAL BLADES PRE STRESSED UNIvERSAL EARLY ENTRY BLADE • Cuts Green Concrete Within 3 Hours Of Finish • Universal Arbor Fits All Early Entry Green Concrete Saws. • High Grade MBS Diamonds For Consistent Cutting, Blade After Blade. • Best Price Value In The Market, longer Life & Faster Cuts. Size Item Number Thickness Seg. Height Please Specify Bond 5” 5CEREECUT .095 10mm Hard Med. M. Soft Soft 5.5” 5.5CEREECUT .095 10mm Hard Med. M. Soft Soft 6” 6CEREECUT .100 10mm Hard Med. M. Soft Soft 8” 8CEREECUT .100 10mm Hard Med. M. Soft Soft 10” 10CEREECUT .100 10mm Hard Med. M. Soft Soft 12” 12CEREECUT .120 10mm Hard Med. M. Soft Soft 12” 12CEREECUT .250 10mm Hard Med. M. Soft Soft 13.5” 13.5CEREECUT .120 10mm Hard Med. M. Soft Soft 13.5” 13.5CEREECUT .250 10mm Hard Med. M. Soft Soft 14” 14CEREECUT .120 10mm Hard Med. M. Soft Soft 14” 14CEREECUT .250 10mm Hard Med. M. Soft Soft *Skid plate shield - included FREE with each blade - attaches to worn skid plate to protect concrete joint against spalling and raveling. *Universal CEREECUT are color coded to match different aggregate conditions. Use wet or dry. LS W/D ☛ THE “BANGER” Concrete Cutting At It’s Best • High Grade MBS impact/heat resistant diamonds for consistent cutting, blade after blade. • Resin filled core to suppress noise, perfect for enclosed locations. • Longer life, and faster, free cutting than any blade on the market today • Custom made for prestressed from 40 years of experience in the market • Cuts your blade cost dramatically • All test results on 8,500 P.S.I. prestressed concrete with 4 strand cable, conducted by a DOT, pre qualified commercial contractor. • Sound Dampening Core • SUPER SOFT bond Ideal for: prestressed concrete, pre-cast, hollow core plank, high psi cured concrete. • All blades custom manufactured to your specifications • Select specifications bellow: 1. Blade Diameter from 12” - 48” Standard Sizes: 12”, 14”, 16” Wet or Dry 20”, 24”, 30”, 32”, 36”, 42”, 48” Wet Only 2. Thickness .125 to .310 3. Laser Welded or Silver Solder 4. Arbor size based on equipment. Part# SHPRESTRESSED 12 CALL FOR QUANTITY DISCOUNTS
- 13. PROFESSIONAL BLADES DOT PRO-SERIES PRO SERIES The PRO-BLADE is truly the finest quality professional blade in the market. With a 40% diamond concentration and a 10mm (.395) segment height, this blade cuts 30% faster and lasts up to 40% longer. Blade specifications meet or exceed demands of Department Of Transportation & Professional Concrete/Asphalt Cutters. These blades are perfect for high horsepower & low RPM walk behind saws. Run wet only - Do not run dry. PRO-1 PRO-2 PRO-3 PRO-4 Cuts: • Cuts: • Cuts: • Cuts: • • CURED CONCRETE • CURED CONCRETE • ASPHALT • ASPHALT OVER • HARD AGGREGATE • SOFT TO MED • GREEN CONCRETE CONCRETE • & SIMILAR MATERIALS AGGREGATE Part# PRO3ASPH Part# PRO4AOC Part# PRO1CC • & SIMILAR MATERIALS LS W 4 LS W 3 Part# PRO2CC LS W 2 LS W 3 • Some blades are available Laser Welded, call for availability. Blade Thickness Diameter .125 .155 .187 .250 .312 .375 .500 .625 12 • • 14 • • •• • •• • • • • • • • • • 16 • • •• • •• • • • 18 • • •• • • •• • • • • • • • • 20 • • •• • • •• • • 24 • • •• •• • •• • • 26 •• • • •• • • • • 30 • •• • • • • • 36 •• • • • 42 •• • 48 * These blades can be made in any thickness or size up to 54”. Allow 3 -4 weeks for delivery on special orders. = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 13
- 14. PROFESSIONAL BLADES DOT PRO-SERIES ULTRA PRO NEW What makes our ULTRA CNC PRO Series by recoMMended ApplicAtion chArt far the best cutting pro blade in the market is the universal diamonds in the segments. hp Very hard Med. hard Medium Med. Soft The innovative technology in these diamond blades achieves both longer lifetime and 25HP- FX40 FX30 FX30 FX30 faster cutting by perfectly aligning diamond grits in the bond matrix. 35HP FX60 FX50 FX50 FX50 In conventional diamond tools, the cutting speed has been inversely proportional 65HP+ FX90 FX60 FX60 FX60 to the life of tools. Through this epoch- manufacturing of the CNC technology, these AGGREGATE CLASSIFICATION MAP OF THE UNITED STATES diamond blades will experience remarkable MED. SOFT MEDIUM MED. HARD VERY HARD enhancement of cutting performance in speed and life simultaneously. Unlike old technology that specify diamonds by grit size for different aggregate hardness, the ULTRA CNC PRO blades are built to cut easily through those tough demanding jobs. ULTRA CNC PRO will cut all cured concrete regardless of aggregate as it is designed for aggregate specific jobs tailored to all cutting conditions and aggregate locations . After years of research and testing both in house and through independent laboratories the finding results show the ULTRA CNC PRO Series outperformed the competition by twice as much in cutting speed and longevity. • Double laser welded • Highest concentration of MBS970 diamonds • Run wet for best performance for best performance select your blade by using the charts provided in this page to match cutting equipment hp to aggregate classification map that best apply for your cutting surface. Try one today! Part# SHCNCFX Diameter FX x Segment Height x Thickness FX30 x 10mm FX40 x 10mm FX50 x 10mm FX60 x 10mm FX70 x 13mm FX90 x 13mm 12” x .125” • • • † • † 12” x .145” • • • † 12” x .160” • † 14” x .125” • • • † • † 14” x .145” • • • † 14” x .160” • • • † 16” x .125” • • • † • † 16” x .145” • • • † 16” x .160” • • † • † 18” x .125” • • • † • † 18” x .145” • • • • † 18” x .160” • • † • † • • 18” x .187” • † • † 20” x .125” • • • † • † 20” x .145” • • • † 20” x .160” • • † • † • • 20” x .187” • † • † 22” x .145” • • • † 22” x .160” • • † • † • • 22” x .187” • † • † 24” x .145” • • • † 24” x .160” • • † • † • • 24” x .187” • † • † 26” x .145” • † 26” x .160” • • • • † • • 26” x .187” • † • † 30” x .160” • • • 30” x .187” • • • 32” x .160” • • • 32” x .187” • • • 36” x .160” • • • 36” x .187” • • † These • blades are also available in 13mm segment height for longer life. Please specify when ordering. 14 CALL FOR QUANTITY DISCOUNTS
- 15. PROFESSIONAL BLADES GRANITE / STONE VENEER 42” x .250” 42ShcncSAnd THIN STONE vENEER CNC 48” x .250” 48ShcncSAnd These new veneer CNC professional diamond saw blades are built with solid cores for both low and high 13 mm Segment Height horse powered saws. Segments are impregnated with high quality diamond and utilizes the Advanced Other sizes & arbors available. Arrangement Technology for productivity and versatility CALL FOR DETAILS of cutting a wide variety of surfaces. These blades are the most universal on the market today and can be used with many different saw systems, gantry, fixed, rail, etc. 12” x .125” x 50mm-60mm 12cncgrAnite CNC GRANITE Patent pending CNC technology gives maximum productivity with the lowest possible cost per inch/ foot cut. MBS 960 diamonds are individually placed in strategic positions to maximize cutting performance. And provides 50% to 100% improvement in blade life and cutting speed. Excellent for cutting Thin Veneer. CNC granite blades offer high cutting ability which results in reduced energy usage and higher productivity than normal blades. 10mm Segment Height Use wet only HS W 2 14” x .125” x 50mm-60mm 14dSilAMpo DSILAMPO 16” x .125” x 50mm-60mm 16dSilAMpo The DSILAMPO blade is engineered to the highest specifications. This blade utilizes the extreme high strength, thermal stabilized Saw-Grade Diamonds in the segments. Silent core built by Edesso and guaranteed not to separate. The 20mm segment height gives the fabricator an opportunity to run longer and gain more life with this quality product. Also the aggressive chip free cutting is why this blade is considered tops in the industry. Fits rail, bridge and gantry saws. 20mm Segment Height Use wet only HS W 2 14” x .125” x 50mm-60mm 14idlgS IDLGS 16” x .125” x 50mm-60mm 16idlgS Our Granite silent series are manufactured to the highest 18” x .125” x 50mm-60mm 18idlgS 20” x .125” x 50mm-60mm 20idlgS standards. Starting with our German copper centered core by EDESSO a true sandwich technology guaranteed not to separate. Our 10mm & 20mm segment heights give the fabricator an opportunity to seek out which is most cost effective for their use. Only the finest high strength, thermally stable diamonds are used in the segments. Fast aggressive chip free cutting is this blades trademark. All sizes in stock and ready to ship anywhere in the world. Full 100% money back guarantee! Fits rail, bridge and gantry saws. Granite. 10mm Segment Height Use wet only HS W 2 = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 15
- 16. CONTINUOUS RIM TILE BLADES POWER STREAK 4” x .080” x 7/8”-5/8” 4chtlSec 4.5” x .080” x 7/8”-5/8” 4.5chtlSec This premium Power Streak series diamond blade utilizes 5” x .080” x 7/8”-5/8” 5chtlSec special grade diamonds for very smooth cutting and long 7” x .080” x DM-5/8” 7chtlSec life. The 10mm rim height yields long blade life. Perfect 8” x .080” x 5/8” 8chtlSec for granite, ceramics, stone, porcelain, tile, limestone 9” x .080” x 5/8” 9chtlSec and similar surfaces. Use wet except for 4, 4.5 & 5 inch, 10” x .080” x 5/8” 10chtlSec these can be used wet or dry. 10mm Rim Height HS ☛ 2 SILvER STREAK 4” x .080” x 7/8”-5/8” 4ShhottlS 4.5” x .080” x 7/8”-5/8” 4.5ShhottlS Our hot pressed .395 continuous rim tile blades are ideal 5” x .080” x 7/8”-5/8” 5ShhottlS for all types of tile, quarry, porcelain, slate, limestone, 7” x .080” x DM-5/8” 7ShhottlS granite, etc... for the contractor who wants quality at a 8” x .080” x 5/8” 8ShhottlS reasonable price. Smooth chip free cutting is due to the 9” x .080” x 5/8” 9ShhottlS utilization of 50/60 mesh size diamonds thus affording 10” x .080” x 5/8” 10ShhottlS the speed you’re after. Use wet except for 4, 4.5 & 5 inch, 12” x .110” x 1” 12ShhottlS these can be used wet or dry. 14” x .110” x 1” 14ShhottlS 10mm Rim Height HS ☛ 2 THE PROFESSIONAL 7” x .080” x DM-5/8” 7SttlS 8” x .080” x 5/8” 8SttlS Our STTLS series is built for the high end user customer 10” x .080” x 5/8” 10SttlS who doesn’t mind paying a reasonable price for the best 12” x .110” x 1” 12SttlS blade he can get. The STTLS will cut hard vitreous ceramics, porcelain, limestone, marble & granite, like 10” x .080” x 5/8” 10StJSlot no other blade on the market. Call today to make your 12” x .110” x 1” 12StJSlot life easier. 7mm Rim Height Use wet. HS W 1 WEDGE CUT 4” x .060” x 7/8”-5/8” 4dMwedgecUt 4.5” x .060” x 7/8”-5/8” 4.5dMwedgecUt Our Wedge Cut blade is for use in the fabrication shop 7” x .060” x DM-5/8” 7dMwedgecUt and for fabrication in the field. It is truly guaranteed to 8” x .060” x DM-5/8” 8dMwedgecUt give you smooth chip free cutting on marble, granite 10” x .065” x 7/8”-5/8” 10dMwedgecUt and porcelain. Also can be used on up to 20HP saws. 12” x .080” x 7/8”-5/8” 12dMwedgecUt Truly for the professional who needs the best blade to 14” x .080” x 7/8”-5/8” 14dMwedgecUt suit their discriminating customer’s taste. 7mm Rim Height Use wet. HS W 1 16 CALL FOR QUANTITY DISCOUNTS
- 17. PROFESSIONAL BLADES SPECIALTY 4” x .040” x 7/8”-20mm-5/8” 4chelSlot RAZOR 4.5” x .040” x 7/8”-20mm-5/8” 4.5chelSlot The “U” Slot electroplated diamond blades are 5” x .040” x 7/8”-20mm-5/8” 5chelSlot 6” x .040” x 7/8”-20mm-5/8” 6chelSlot designed for rugged and aggressive cutting of marble, 7” x .040” x DM-5/8” 7chelSlot fiberglass, Corian™ & other man made materials. The discriminating customer will appreciate the fast aggressive cutting action of the EL SLOT. These should be used wet but can run dry for short runs. 5mm Segment Height HS W/D 4 4” x .050” x 7/8”-5/8” 4chelectroSeg TSUNAMI 4.5” x .050” x 7/8”-5/8” 4.5chelectroSeg These Electroplated Segmented blades are built with a 5” x .050” x 7/8”-5/8” 5chelectroSeg super bond that holds the diamonds rigidly in place, while 7” x .050” x 7/8”-5/8” 7chelectroSeg providing exposed diamonds to cut the work piece. The special plating on these blades provide for fast chip free cutting. Ideal for cutting fiberglass, composites, plastics, graphite and marble. Use these blades on hand held or stationary machines. These should be used wet but can run dry for short runs. 5mm Segment Height HS W/D 4 14” x .160” x Special 14gtringSAw UNIvERSAL RING SAW BLADE 14” x .225” x Special 14gtringSAw.225 This blade provides extreme cutting depths when *Drive Wheel Included mounted on the proper hand held saw. Premium grade ring saw blade for hard materials is perfect for concrete walls, precast concrete and concrete pipes. Premium grade ring saw blade for hard materials. 8mm Segment Height Use wet or dry. HS W/D 3 14” x .160” x Special 14cncringSAw CNC RING SAW *Drive Wheel Included The CNC cutting advantage, 35% faster and twice the blade life. What makes this blade so outstanding is the patented diamond placement in the matrix. This prevents premature diamond failure due to the lack of crushed or shattered diamonds. Our new diamond system just keeps... Cutting... Longer... Faster. Cuts: Cured concrete, concrete with rebar and similar surfaces. 8mm Segment Height Use wet or dry. HS W/D 2 12” x .150” x 1”-20mm 12root ROOT RIPPER - FIRE RESCUE 12” x .150” x 20mm 12root20 The first choice for fire rescue. This blade cuts and rips 14” x .150” x 1”-20mm 14root 14” x .150” x 20mm 14root20 through roofs and wall siding, as well as the metal in autos and trucks. Making entry more accessible for emergency situations. This blade is also a perfect tool for the nursery industry, forestry division and farming community to use for quick cutting of tree roots. Root Rippers are edged with C3 carbide & laser welded. 12mm Segment Height Use wet or dry. HS W/D = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 17
- 18. RESTORATION CRACK CHASERS CRACK SEGGY 4” x .375” x Threaded 4gtcrAckt 4” x .375” x Non-threaded 4gtcrAck These wheels efficiently widen existing cracks and 5” x .375” x Threaded 5gtcrAckt provide an ideal groove for sealing preparation. The 5” x .375” x Non-threaded 5gtcrAck high percentage of diamonds in the matrix provide for 7” x .375” x Threaded 7gtcrAckt excellent speed and long wheel life. 7” x .375” x Non-threaded 7gtcrAck Use wet or dry. 8” x .375” x Threaded 8gtcrAckt HS W/D 2 8” x .375” x Non-threaded 8gtcrAck CRACK SEGGY PREMIUM 4” x .375” x 7/8”-5/8” 4ShcrAckV This v shaped segmented rim crack chaser wheel efficiently widens existing cracks and provides an ideal groove for sealing preparation. Perfect companion tool for widening floor seams to lay down water, electrical and other under surface materials. Use wet or dry. HS W/D 2 CRACK TURBO 4” x .375” x Threaded 5/8-11 4ShcrAck This high diamond concentrated wheel is the fastest and most effective way to widen existing cracks. These are .375 thick and come with a 5/8 by 11 thread. This pro-series the 10V is the best on the market of its kind- guaranteed! Use wet or dry. HS W/D 2 18 CALL FOR QUANTITY DISCOUNTS
- 19. RESTORATION TUCK POINTERS 4” x .250” x 7/8”-5/8” 4gASAndtp DUO-TUCK 4.5” x .250” x 7/8”-5/8” 4.5gASAndtp Our Grape Ape Tuck Series, Duo-Tuck (a sandwich tuck 5” x .250” x 7/8”-5/8” 5gASAndtp 7” x .250” x 7/8”-5/8” 7gASAndtp pointer) provides superior cutting ability for aggressive and rapid mortar removal with a minimum of equipment strain. Less friction means faster grinds. 10mm Segment Height Use wet or dry. HS W/D 2 4” x .375” x 7/8”-5/8” 4gASAndtriptp TRIP-TUCK 4.5” x .375” x 7/8”-5/8” 4.5gASAndtriptp Our Grape Ape Tuck Series, Trip-Tuck (a sandwich tuck 5” x .375” x 7/8”-5/8” 5gASAndtriptp pointer) provides superior cutting ability for aggressive and rapid mortar removal with a minimum of equipment strain. Less friction means faster grinds. 10mm Segment Height Use wet or dry. HS W/D 2 4” x .250” x 7/8”-5/8” 4diYtpS BLASTER 4.5” x .250” x 7/8”-5/8” 4.5diYtpS Our 10mm segmented height Supreme Tuck Points are 5” x .250” x 7/8”-5/8” 5diYtpS 7” x .250” x 7/8”-5/8” 7diYtpS among the best on the market. By far our most popular tuck pointer. For those looking for long life & fast grinding speeds at a low cost. Find out today what so many of our customers already know about our line. We Guarantee Your Satisfaction! • Also available in .375 & .500 thickness • Call for pricing ! 10mm Segment Height Use wet or dry. HS W/D 2 4” x .250” x 7/8”-5/8” 4gbtp.250 CHARGER-T 4.5” x .250” x 7/8”-5/8” 4.5gbtp.250 The body design and 10mm high diamond segments 5” x .250” x 7/8”-5/8” 5gbtp.250 make this unique tuck pointer extremely aggressive while providing a long blade life. Fast speeds make this a great companion tool for restoration contractors. 10mm Segment Height Use wet or dry. HS W/D 3 = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 19
- 20. CORE DRILLING COREBITS SEGMENT CLOSE-UP CONTRACTOR DRY SERIES 1” x 10” x 5/8”-11 1chdrYcorebit 1.5” x 10” x 5/8”-11 1.5chdrYcorebit These premium CONTRACTOR DRY core bits are built 2” x 10” x 5/8”-11 2chdrYcorebit for those job locations that have no water feed. Body 2.5” x 10” x 5/8”-11 2.5chdrYcorebit air vents allow fast, clean drilling and extraction of filled 3” x 10” x 5/8”-11 3chdrYcorebit substance. Perfect for block. 3.5” x 10” x 5/8”-11 3.5chdrYcorebit 4” x 10” x 5/8”-11 4chdrYcorebit Do not use in reinforced concrete. 4.5” x 10” x 5/8”-11 4.5chdrYcorebit Use on angle grinders. 5” x 10” x 5/8”-11 5chdrYcorebit 7mm Segment Height 6” x 10” x 5/8”-11 6chdrYcorebit SEGMENT CLOSE-UP PROFESSIONAL DRY SERIES 1” x 10” x 5/8”-11 1ShdrYcorebit 1.25” x 10” x 5/8”-11 1.25ShdrYcorebit These supreme PROFESSIONAL DRY core bits are built 1.5” x 10” x 5/8”-11 1.5ShdrYcorebit for those job locations that have no water feed. High 1.75” x 10” x 5/8”-11 1.75ShdrYcorebit quality diamonds and additional segments provide 2” x 10” x 5/8”-11 2ShdrYcorebit longer life and faster cuts. Body air vents allow fast, 2.25” x 10” x 5/8”-11 2.25ShdrYcorebit clean drilling and extraction of filled substance. Perfect 2.5” x 10” x 5/8”-11 2.5ShdrYcorebit for block. 3” x 10” x 5/8”-11 3ShdrYcorebit 3.5” x 10” x 5/8”-11 3.5ShdrYcorebit Do not use in reinforced concrete. 4” x 10” x 5/8”-11 4ShdrYcorebit Use on angle grinders. 4.5” x 10” x 5/8”-11 4.5ShdrYcorebit 8mm Segment Height 5” x 10” x 5/8”-11 5ShdrYcorebit 6” x 10” x 5/8”-11 6ShdrYcorebit 20 CALL FOR QUANTITY DISCOUNTS
- 21. CORE DRILLING COREBITS 1” x 17” x 1-1/4”-7 1chcorebit CONTRACTOR SERIES SEGMENT CLOSE-UP 1.5” x 17” x 1-1/4”-7 1.5chcorebit 2” x 17” x 1-1/4”-7 2chcorebit These PROFESSIONAL GRADE core bits are 2.5” x 17” x 1-1/4”-7 2.5chcorebit manufactured to exacting specifications and built for a 3” x 17” x 1-1/4”-7 3chcorebit variety of drilling jobs. Designed to tackle a broad range 3.5” x 17” x 1-1/4”-7 3.5chcorebit 4” x 17” x 1-1/4”-7 4chcorebit of applications, including medium reinforced concrete 4.5” x 17” x 1-1/4”-7 4.5chcorebit and other masonry materials. 7.5mm segment height 5” x 17” x 1-1/4”-7 5chcorebit 7mm Segment Height Wet cutting. 5.5” x 17” x 1-1/4”-7 5.5chcorebit 6” x 17” x 1-1/4”-7 6chcorebit 6.5” x 17” x 1-1/4”-7 6.5chcorebit 7” x 17” x 1-1/4”-7 7chcorebit 8” x 17” x 1-1/4”-7 8chcorebit 10” x 17” x 1-1/4”-7 10chcorebit 12” x 17” x 1-1/4”-7 12chcorebit All Sizes Available 3/4” to 18” 2” x 17” x 1-1/4”-7 2Shcorep PREMIUM SERIES SEGMENT CLOSE-UP 2.25” x 17” x 1-1/4”-7 2.25Shcorep 2.5” x 17” x 1-1/4”-7 2.5Shcorep These PREMIUM GRADE core bits are manufactured to 3” x 17” x 1-1/4”-7 3Shcorep the highest specifications and designed for a multitude 3.5” x 17” x 1-1/4”-7 3.5Shcorep of drilling applications. Example: cutting into highways, 4” x 17” x 1-1/4”-7 4Shcorep runways, dams, buildings, bridges, parking garages, 4.25” x 17” x 1-1/4”-7 4.25Shcorep walls, floors, culverts, drainage pipes and more. 4.5” x 17” x 1-1/4”-7 4.5Shcorep 5” x 17” x 1-1/4”-7 5Shcorep 7.5mm Segment Height Wet cutting. 5.5” x 17” x 1-1/4”-7 5.5Shcorep 6” x 17” x 1-1/4”-7 6Shcorep 6.5” x 17” x 1-1/4”-7 6.5Shcorep 7” x 17” x 1-1/4”-7 7Shcorep 8” x 17” x 1-1/4”-7 8Shcorep 10” x 17” x 1-1/4”-7 10Shcorep All Sizes Available to 24” 12” x 17” x 1-1/4”-7 12Shcorep 2” x 17” x 1-1/4”-7 2Shcorepp PREMIUM PLUS SERIES SEGMENT CLOSE-UP 2.25” x 17” x 1-1/4”-7 2.25Shcorepp 2.5” x 17” x 1-1/4”-7 2.5Shcorepp These PREMIUM GRADE core bits are manufactured to 3” x 17” x 1-1/4”-7 3Shcorepp the highest specifications and designed for a multitude 3.5” x 17” x 1-1/4”-7 3.5Shcorepp of drilling applications. Such as cutting into highways, 4” x 17” x 1-1/4”-7 4Shcorepp runways, dams, buildings, bridges, parking garages, 4.25” x 17” x 1-1/4”-7 4.25Shcorepp walls, floors, culverts, drainage pipes and more. The 4.5” x 17” x 1-1/4”-7 4.5Shcorepp 5” x 17” x 1-1/4”-7 5Shcorepp Premium Plus has a higher concentration of MBS 5.5” x 17” x 1-1/4”-7 5.5Shcorepp thermal grade diamonds; faster cuts, longer life. 6” x 17” x 1-1/4”-7 6Shcorepp 8mm Segment Height Wet cutting. 6.5” x 17” x 1-1/4”-7 6.5Shcorepp 7” x 17” x 1-1/4”-7 7Shcorepp 8” x 17” x 1-1/4”-7 8Shcorepp 10” x 17” x 1-1/4”-7 10Shcorepp 12” x 17” x 1-1/4”-7 12Shcorepp 2” x 17” x 1-1/4”-7 2Shcoreppf PREMIUM PLUS FULL SERIES SEGMENT CLOSE-UP 2.25” x 17” x 1-1/4”-7 2.25Shcoreppf 2.5” x 17” x 1-1/4”-7 2.5Shcoreppf These full segmented PREMIUM GRADE core bits are 3” x 17” x 1-1/4”-7 3Shcoreppf manufactured to the highest specifications and designed 3.5” x 17” x 1-1/4”-7 3.5Shcoreppf for a multitude of drilling applications. Such as cutting into 4” x 17” x 1-1/4”-7 4Shcoreppf highways, runways, dams, buildings, bridges, parking 4.25” x 17” x 1-1/4”-7 4.25Shcoreppf garages, walls, floors, culverts, drainage pipes and more. 4.5” x 17” x 1-1/4”-7 4.5Shcoreppf 5” x 17” x 1-1/4”-7 5Shcoreppf The Premium Plus F has a higher concentration of MBS 5.5” x 17” x 1-1/4”-7 5.5Shcoreppf thermal grade diamonds; faster cuts, longer life. 6” x 17” x 1-1/4”-7 6Shcoreppf 8mm Segment Height Wet cutting. 6.5” x 17” x 1-1/4”-7 6.5Shcoreppf 7” x 17” x 1-1/4”-7 7Shcoreppf 8” x 17” x 1-1/4”-7 8Shcoreppf 10” x 17” x 1-1/4”-7 10Shcoreppf 12” x 17” x 1-1/4”-7 12Shcoreppf = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 21
- 22. CORE DRILLING COREDRILL RIGS / ACCESSORIES DK 6 DK 10 DK 12 This heavy duty 15 Amp Single Load Equipped with a 2-speed 20 Amp This monster is equipped with a 30 Motor can handle up to 8” diameter Super Duty Motor. This work horse Amp, 2-speed HD motor & has the Diamond Core Bits can core drill to 12” diameter holes capacity to 14” standard and can be and be adapted to drill up to 16” retrofitted to run up to 20” cores With a built-in slip clutch and roller diameter. carriage. This DK-6 makes core drilling a snap. • Full line of replacement parts available for all Coredrill Rigs. Please Call • COMPLETE DRILL RIGS AvAILABLE WITH OR WITHOUT PAD & PUMP vACUUM SYSTEM. vACUUM PUMP & PAD ASSEMBLY* Vacuum Hose ihhVAchoSeASSeM Water Hose ihhwAterhoSeASS Quick Connect plug ihhMAleplUg Vacuum Pad VAc-pAd Vacuum Pump VAc-pUMp *Available for all Model Core Drilling Machines. This vacuum base pad & pump assembly enables you to effectively hold down drill core machines both vertically & horizontally without the use of a concrete anchor ACCESSORIES 6” x 1-1/4”-7 Extension 120-6eXtenSion 6” x 5/8”-11 Extension 125-6eXtenSion Adapters • Extensions 12” x 1-1/4”-7 Extension 12” x 5/8”-11 Extension 120-12eXtenSion 125-12eXtenSion Reducers • Couplings Step Down Adapter corebitAdApter Step Up Adapter corebitAdApter2 22 CALL FOR QUANTITY DISCOUNTS
- 23. CORE DRILLING CROWNBITS 0.5” x 2”h .50gtcrown PILOT CROWN PRO 0.75” x 2”h .75gtcrown These medium wall professional core bits make drilling 1.125” x 2”h 1.125gtcrown 1.25” x 2”h 1.25gtcrown smooth precision holes, clean and very easy. The 3/8” 1.375” x 2”h 1.375gtcrown diameter drill bit pilots the GT CROWN for precise cutting 1.5” x 2”h 1.5gtcrown work on granite, marble, stone and ceramic tile. The bit 1.625” x 2”h 1.625gtcrown fits easily in all electric drill chucks. Drill depth 2”. 1.75” x 2”h 1.75gtcrown Use wet or dry. 1.875” x 2”h 1.875gtcrown 2” x 2”h 2gtcrown 1.25” x 2”h 1.25dStwcore CROWN CORE 1.375” x 2”h 1.375dStwcore The thick wall, steel tooled body is constructed for more 1.5” x 2”h 1.5dStwcore 2” x 2”h 2dStwcore stability and higher rate of penetration. Wider diamond segments for longer rotational speed and bit loads. The highly efficient crown bit makes perfect holes in granite, marble, stone and ceramic tile. Use wet or dry. Threaded = 5/8”-11 0.25” x 2”h .25Shcrown SHCROWNS 0.625” x 2”h .625Shcrown These high quality, steel tooled body crown bits are 0.75” x 2”h .75Shcrown 0.875” x 2”h .875Shcrown constructed to provide a high rate of penetration hole 1” x 2”h 1Shcrown after hole. High quality diamonds in the segments gives 1.125” x 2”h 1.125Shcrown this tool longer life and faster cuts. Perfect for granite, 1.25” x 2”h 1.25Shcrown marble, stone, and man made materials. 1.5” x 2”h 1.5Shcrown Use wet or dry. 1.75” x 2”h 1.75Shcrown Threaded = 5/8”-11 0.25” x 2”h .25dtbrcorebit DTBRCOREBIT 0.75” x 2”h .75dtbrcorebit We manufacture these high quality super fast brazed 1.125” x 2”h 1.125dtbrcorebit 1.25” x 2”h 1.25dtbrcorebit crown bits for cutting precision, smooth and clean holes. 1.375” x 2”h 1.375dtbrcorebit The long life of these crowns are perfect for precise 1.5” x 2”h 1.5dtbrcorebit cutting work on marble, granite and ceramic tile. 2” x 2”h 2dtbrcorebit Use wet or dry. 2.5” x 2”h 2.5dtbrcorebit 3” x 2”h 3dtbrcorebit 4” x 2”h 4dtbrcorebit 4.25” x 2”h 4.25dtbrcorebit Threaded = 5/8”-11 1” x 2”h 1lkVbcorebit LKvBCOREBIT 1.25” x 2”h 1.25lkVbcorebit This thin wall, segmented, surface set diamond crowns 1.375” x 2”h 1.375lkVbcorebit 2.125” x 2”h 2.125lkVbcorebit are designed for fast, efficient cutting and extended life. 2.5” x 2”h 2.5lkVbcorebit The piloting guide bit ensures non slip start up. 3.5” x 2”h 3.5lkVbcorebit Use on: ceramic tile, porcelain tile 3/8” Shank Use wet or dry. = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 23
- 24. SURFACE PREPARATION GRINDING WHEELS METAL DUST SHROUD 7” 7SpdUStShroUd This Grinding wheel cover is constructed with a solid top plate and a flexible rubber skirt molded into base. The shroud allows working tight to wall. For use with 7” cup wheels. Also has dust attachment for vacuum. SINGLE ROW CUPS STORM I & II 4” x Threaded 4gtcUpSglt 5” x Threaded 5gtcUpSglt Storm Cup diamond wheels are the perfect tool in 7” x Threaded 7gtcUpSglt construction for concrete surface preparation and tilt 4” x Non-Threaded 4gtcUpSgl wall finishing. Also perfect for fast grinding and rough 5” x Non-Threaded 5gtcUpSgl de-burring. Ideal for the contractor who is concerned 7” x Non-Threaded 7gtcUpSgl DOUBLE ROW CUPS with up front costs. Available in either 5/8x11 thread 4” x Threaded 5/8”-11 4gtcUpdblt design or 7/8x5/8, please specify when ordering. 5” x Threaded 5/8”-11 5gtcUpdblt Use wet or dry. 7” x Threaded 5/8”-11 7gtcUpdblt HS W/D 2 4” x Non-Threaded 4gtcUpdbl 5” x Non-Threaded 5gtcUpdbl Threaded = 5/8”-11 Non-Threaded = 7/8”-5/8” 7” x Non-Threaded 7gtcUpdbl SINGLE ROW CUPS TORNADO I & II 4” x Threaded 4ShcUpSglt 5” x Threaded 5ShcUpSglt These diamond grinding cups are designed for rough 7” x Threaded 7ShcUpSglt work and rapid stock removal of concrete, stone and 4” x Non-Threaded 4ShcUpSgl masonry. This style is considered one of the best in the 5” x Non-Threaded 5ShcUpSgl market today! Available in either 5/8x11 thread design or 7” x Non-Threaded 7ShcUpSgl DOUBLE ROW CUPS 7/8x5/8, please specify when ordering. 4” x Threaded 5/8”-11 4ShcUpdblt Use wet or dry. 5” x Threaded 5/8”-11 5ShcUpdblt HS W/D 2 7” x Threaded 5/8”-11 7ShcUpdblt 4” x Non-Threaded 4ShcUpdbl 5” x Non-Threaded 5ShcUpdbl Threaded = 5/8”-11 Non-Threaded = 7/8”-5/8” 7” x Non-Threaded 7ShcUpdbl TWISTER PRO 4” x Threaded x 8 Segs 4gtcUpSwirlt 4” x Non-Threaded x 8 Segs 4gtcUpSwirl The aggressive nature of the TWISTER-PRO provides for 4” x Threaded x 14 Segs 4gtcUpSwirl14t very fast cutting action on masonry and stone. This type 4” x Non-Threaded x 14 Segs 4gtcUpSwirl14 of cup leaves little or no swirl marks. This wheel will give 4.5” x Threaded x 9 Segs 4.5gtcUpSwirlt 4.5” x Non-Threaded x 9 Segs 4.5gtcUpSwirl you 30% longer life over most cups in the market. 4.5” x Threaded x 18 Segs 4.5gtcUpSwirl18t Use wet or dry. 4.5” x Non-Threaded x 18 Segs 4.5gtcUpSwirl18 HS W/D 2 7” x Threaded x 12 Segs 7gtcUpSwirlt 7” x Non-Threaded x 12 Segs 7gtcUpSwirl 7” x Threaded x 24 Segs 7gtcUpSwirl24t 7” x Non-Threaded x 24 Segs 7gtcUpSwirl24 Threaded = 5/8”-11 Non-Threaded = 7/8”-5/8” TURBO PLUS 4” x Threaded 4gttUrbocct 5” x Threaded 5gttUrbocct These unique grinding cups are specifically designed for 6” x Threaded 6gttUrbocct fast stock removal of concrete, stone and masonry, with 7” x Threaded 7gttUrbocct very low dust. An excellent choice for those looking for 4” x Non-Threaded 4gttUrbocc value performance. 5” x Non-Threaded 5gttUrbocc Use wet or dry. 6” x Non-Threaded 6gttUrbocc HS W/D 2 7” x Non-Threaded 7gttUrbocc Threaded = 5/8”-11 Non-Threaded = 7/8”-5/8” *Also available in medium and fine 24 CALL FOR QUANTITY DISCOUNTS
- 25. SURFACE PREPARATION GRINDING WHEELS 4” x Threaded 4ShhottUrbocct TURBO DEvIL 4.5” x Threaded 4.5ShhottUrbocct These Turbo Devil diamond grinding cups are specifically 5” x Threaded 5ShhottUrbocct 7” x Threaded 7ShhottUrbocct designed for fast stock removal of concrete, stone and 4” x Non-Threaded 4ShhottUrbocc masonry, with very low dust. An excellent choice for finer 4.5” x Non-Threaded 4.5ShhottUrbocc finish grinding. 5” x Non-Threaded 5ShhottUrbocc Use wet or dry. 7” x Non-Threaded 7ShhottUrbocc HS W/D 2 Threaded = 5/8”-11 Non-Threaded = 7/8”-5/8” 4” x Threaded 4ShtUrbocct TURBO DEvIL PRO 5” x Threaded 5ShtUrbocct The Turbo Devil Pro cup is a dry running grinding disc 6” x Threaded 6ShtUrbocct 7” x Threaded 7ShtUrbocct ideal for those jobs that require a fast and smooth polish. 4” x Non-Threaded 4ShtUrbocc This cup is perfect for finishing granite, marble, tile & 5” x Non-Threaded 5ShtUrbocc porcelain, refractory, light duty masonry and concrete. 6” x Non-Threaded 6ShtUrbocc Try One Today! 7” x Non-Threaded 7ShtUrbocc Use wet or dry. HS W/D 2 *Also available in medium and fine Threaded = 5/8”-11 Non-Threaded = 7/8”-5/8” 7” x Threaded 7chfAncUpt THE FAN 7” x Non-Threaded 7chfAncUp This computer designed diamond grinding cup provides the best of all features in grinding tools. The FAN wheel is highly aggressive as a surface prep tool. • Runs extremely cool, providing a 35-50% faster speed • No or very slight swirl marks • Core thickness .150”/Seg depth, 3/16”/Long segs 2” OAL • For CONCRETE-TERRAZZO-SIMILAR SURFACES Use wet or dry. HS W/D 2 Threaded = 5/8”-11 Non-Threaded = 7/8”-5/8” 4” x Threaded 4ShhottSegcUpt T-SEG CUP 4.5” x Threaded 4.5ShhottSegcUpt The aggressive nature of the T-SEG Cup provides fast 5” x Threaded 5ShhottSegcUpt 7” x Threaded 7ShhottSegcUpt smooth grinding action on concrete, masonry and stone. 4” x Non-Threaded 4ShhottSegcUp This type of cup leaves little or no swirl marks. Field tests 4.5” x Non-Threaded 4.5ShhottSegcUp prove this T-SEG CUP will give longer life than most cups 5” x Non-Threaded 5ShhottSegcUp in the market. 7” x Non-Threaded 7ShhottSegcUp Use wet or dry. Threaded = 5/8”-11 Non-Threaded = 7/8”-5/8” 4” x Non-Threaded 4hkUcUp U CUP 4.5” x Non-Threaded 4.5hkUcUp Special U-Shape design offers faster and highly 5” x Non-Threaded 5hkUcUp 7” x Non-Threaded 7hkUcUp aggressive grinding with excellent dust removal for heavy-duty professional work. Use wet or dry. HS W/D 2 Non-Threaded = 7/8”-5/8” = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 25
- 26. SURFACE PREPARATION GRINDING WHEELS CRYSTAL CUP 4” x Non-Threaded 4hkcrYStAlcUp 4.5” x Non-Threaded 4.5hkcrYStAlcUp Crystal shape design offer faster and more aggressive 5” x Non-Threaded 5hkcrYStAlcUp grinding with excellent dust removal for heavy duty 7” x Non-Threaded 7hkcrYStAlcUp professional work. Use wet or dry. HS W/D 2 BLUE DROP CUP 4” x Non-Threaded 4hklteArdrop 4.5” x Non-Threaded 4.5hklteArdrop This Blue Drop design offer faster and more aggressive 5” x Non-Threaded 5hklteArdrop grinding with excellent dust removal for heavy duty 7” x Non-Threaded 7hklteArdrop professional work. Use wet or dry. HS W/D 2 FLOOR WHEEL CUP 4” x Non-Threaded 4hkpcdwheel 4.5” x Non-Threaded 4.5hkpcdwheel For removal of glue, epoxy, VCT mastic and other 5” x Non-Threaded 5hkpcdwheel coatings on floor. Followed with 6 grit or 16 grit metal 7” x Non-Threaded 7hkpcdwheel bond diamond wheel. Use wet or dry. HS W/D 2 SEG PLATE PRO-10 10” x 3/4” 10JotSegplAte Replacement Segs 30/40 Grit Seg-30/40 The big advantage of using our plates is the ability to use and replace segments as needed. Never buy another mounting plate only the grinding segments as needed. The segments bolt in place on the plate. One can run fewer segments for more aggressive grinding or fill the plate completely with segments for an extremely smooth finish. Designed to smooth rough patched surfaces, sidewalks, pads, patios, streets & industrial floors. Easily grinds down bumps & rough joints. Big money saver! SEG PLATE PRO-7 7” x 5/8”-11 Threaded 7SSSegplAte Replacement Segs 30/40 Grit Seg-30/40 The big advantage of using our plates is the ability to use and replace segments as needed. Never buy another mounting plate only the grinding segments as needed. The segments bolt in place on the plate. One can run fewer segments for more aggressive grinding or fill the plate completely with segments for an extremely smooth finish. Designed to smooth rough patched surfaces, sidewalks, pads, patios, streets & industrial floors. Easily grinds down bumps & rough joints. Big money saver! 26 CALL FOR QUANTITY DISCOUNTS
- 27. SURFACE PREPARATION POLISHING TOOLS / BACKPADS 5/8”-11 Thread 4ZAirpoliSher AIR POWERED WET POLISHER/GRINDER This extremely well engineered pneumatic polishing tool is made of aircraft aluminum and designed for continuous operating day in and day out. This light weight tool utilizes water-tight sealed bearings. Sturdy alloy gears and noise reduction housing. Variable operating speeds from 240 to 4500 RPM. This unit comes complete with water hoses, brass fittings and wrench. Use with our Velcrobacked pads from 3 inch to 5 inch. 3” x Threaded 3gtbAckpAd FLEX BACK PAD 4” x Threaded 4gtbAckpAd These flex back pads are good for straight edge polishing 5” x Threaded 5gtbAckpAd and also soft flexing for ogee like edge polishing. Threaded = 5/8”-11 4” x Threaded 4hkridgidbAckpAd RIGID BACK PAD Designed for straight edge polishing. Velcro backing for super adhesive bonding of pad to backing for preventing separation. Threaded = 5/8”-11 3” x Threaded 3kfbAckpAd FOAM BACK PAD 4” x Threaded 4kfbAckpAd These durable rubber Back Pad holders have velcro 5” x Threaded 5kfbAckpAd bonded to back of holder, making pad changing as easy as 1,2,3. Molded with a brass thread insert for universal thread mounting. Velcro Backing. Threaded = 5/8”-11 4” x Threaded 4hkAlUMbAckpAd ALUMINUM BACK PAD These rigid aircraft aluminum body and rigid rubber body back pad holders have velcro bonded to back of holder, making pad changing very easy. Standard thread insert for universal mounting. Velcro Backing. Threaded = 5/8”-11 = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 27
- 28. SURFACE PREPARATION POLISHING PADS EC FLEX 3” / 4” / 5” x 50grit hk50ecfleX 3” / 4” / 5” x 100grit hk100ecfleX The EC Flex pads work very efficiently providing a fine 3” / 4” / 5” x 200grit hk200ecfleX polish at an economical cost. A full range of grit sizes 3” / 4” / 5” x 400grit hk400ecfleX for all marble, granite and natural stone applications. 3” / 4” / 5” x 800grit hk800ecfleX Designed for use with most wet grinders & polishers and 3” / 4” / 5” x 1500grit hk1500ecfleX rated 1200 to 3000 RPM. 3” / 4” / 5” x 3000grit hk3000ecfleX Specify Dia. 3”, 4”, 5” 3” / 4” / 5” (White) hkbUffecfleXw 3” / 4” / 5” (Black) hkbUffecfleXb BLACK MAGIC 4” / 5” x 50grit fhblkMAgic50 4” / 5” x 100grit fhblkMAgic100 Premium polishing pads that are very durable and provide 4” / 5” x 200grit fhblkMAgic200 top performance for a crystal smooth finish. These pads 4” / 5” x 400grit fhblkMAgic400 are very flexible even after continual use. Use on granite, 4” / 5” x 800grit fhblkMAgic800 marble, natural and synthetic stone. 4” / 5” x 1500grit fhblkMAgic1500 Rated 1200 to 3000 RPM. 4” / 5” x 3000grit fhblkMAgic3000 Specify Dia. 4”, 5” 4” / 5” x Buff (White) fhblkMAgicwht • Resin is black on all Grits • 4” / 5” x Buff (Black) fhblkMAgicblk NEOFLEX 3” / 4” / 5” x 50grit hk50neopAd 3” / 4” / 5” x 100grit hk100neopAd These NEW NEOFLEX diamond resin pads are engineered 3” / 4” / 5” x 200grit hk200neopAd for a highly lustrous finish on natural stone. Flexible 3” / 4” / 5” x 400grit hk400neopAd for long life over flat and convex/ concave surfaces. 3” / 4” / 5” x 800grit hk800neopAd Designed for hand grinders and floor machines. Polish 3” / 4” / 5” x 1500grit hk1500neopAd granite, marble & natural stone. 3” / 4” / 5” x 3000grit hk3000neopAd Rated 1200 to 3000 RPM. 3” / 4” / 5” x Buff (White) hkbUffneopAdw Specify Dia. 3”, 4”, 5” 3” / 4” / 5” x Buff (Black) hkbUffneopAdb SHINE PAD 3” / 4” / 5” x 50grit hk50ShinepAd 3” / 4” / 5” x 100grit hk100ShinepAd The NEW diamond Shine Pads are designed for a highly 3” / 4” / 5” x 200grit hk200ShinepAd lustrous polish. Very flexible for long life over flat and 3” / 4” / 5” x 400grit hk400ShinepAd intricate surfaces. Designed for hand grinders and floor 3” / 4” / 5” x 800grit hk800ShinepAd machines. Polishing granite, marble & natural stone. 3” / 4” / 5” x 1500grit hk1500ShinepAd Rated 1200 to 3000 RPM. 3” / 4” / 5” x 3000grit hk3000ShinepAd Color coded for grit identification. 3” / 4” / 5” x Buff (White) hkbUffShinepAdw Specify Dia. 3”, 4”, 5” 3” / 4” / 5” x Buff (Black) hkbUffShinepAdb 28 CALL FOR QUANTITY DISCOUNTS
- 29. SURFACE PREPARATION POLISHING PADS 4” x 50grit hk50drYfleX DRY FLEX PADS 4” x 100grit hk100drYfleX Dry pads are engineered for use on job sites where 4” x 200grit hk200drYfleX 4” x 400grit hk400drYfleX running dry is necessary. Also good for conforming to 4” x 800grit hk800drYfleX ogee and bullnose shape surfaces. Velcro backing for 4” x 1500grit hk1500drYfleX fast pad changing. Color coded for grit size. 4” x 3000grit hk3000drYfleX Can be used wet for longer life. 4” x Buff hkbUffdrYfleX • DPDRYPADS also available • Call for pricing ! 3” / 5” x 50grit hkconcdrY50 DIAMOND GLIDE CONCRETE PADS 3” / 5” x 100grit hkconcdrY100 Diamond Resin Pads are designed for polishing concrete. 3” / 5” x 200grit hkconcdrY200 3” / 5” x 400grit hkconcdrY400 These long life, very aggressive pads are made with 3” / 5” x 800grit hkconcdrY800 high quality diamonds and velcro backing. The flexibility 3” / 5” x 1500grit hkconcdrY1500 makes polishing rounded or curved areas easier than 3” / 5” x 3000grit hkconcdrY3000 ever. Fits all machines on the market. Use wet or dry 3” / 5” x 30grit hkconcdrY30t X-THICK CONCRETE PADS 3” / 5” x 50grit hkconcdrY50t These extra thick Diamond Resin Pads are designed 3” / 5” x 100grit hkconcdrY100t 3” / 5” x 200grit hkconcdrY200t for polishing concrete. These thicker long life, very 3” / 5” x 400grit hkconcdrY400t aggressive pads are made with high quality diamonds and 3” / 5” x 800grit hkconcdrY800t velcro backing. The flexibility makes polishing rounded 3” / 5” x 1500grit hkconcdrY1500t or curved areas easier than ever. Fits all machines on 3” / 5” x 3000grit hkconcdrY3000t the market. Use wet or dry 3” / 4” x 30grit dt30roSeX DT ROSEX 3” / 4” x 50grit dt50roSeX ROSEX diamond resin discs are manufactured with high 3” / 4” x 120grit dt120roSeX 3” / 4” x 220grit dt220roSeX segments for long life and also have a uniquely designed 3” / 4” x 400grit dt400roSeX waterway channel for swarf removal. The flat surface 3” / 4” x 600grit dt600roSeX grinds and polishes the stone to a lustrous factory finish. 3” / 4” x 800grit dt800roSeX These discs are designed to glide over lippage of all 3” / 4” x 1800grit dt1800roSeX heights. 3” / 4” x 3500grit dt3500roSeX 3” / 4” x 8500grit dt8500roSeX = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 29
- 30. SURFACE PREPARATION POLISHING PADS DT TYPHOON 3” / 4” x 30grit dt30tYphoon 3” / 4” x 50grit dt50tYphoon TYPHOON diamond resin discs are specially designed 3” / 4” x 120grit dt120tYphoon for long life and producing a high gloss finish. This newly 3” / 4” x 220grit dt220tYphoon designed pattern will give a high gloss finish, remove 3” / 4” x 400grit dt400tYphoon swarf and allow polishing in those difficult angles in and 3” / 4” x 600grit dt600tYphoon around corners and walls. 3” / 4” x 800grit dt800tYphoon 3” / 4” x 1800grit dt1800tYphoon 3” / 4” x 3500grit dt3500tYphoon 3” / 4” x 8500grit dt8500tYphoon TURBO CAT 3” / 4” x 50grit dt30tUrbocAt 3” / 4” x 50grit dt50tUrbocAt These discs are designed for extremely heavy stock 3” / 4” x 100grit dt100tUrbocAt removal applications. Special bond for super fast speed. 3” / 4” x 200grit dt200tUrbocAt Perfect for grinding materials such as granite, marble, 3” / 4” x 325grit dt325tUrbocAt terrazzo, natural stone & concrete. Use on hand held or floor machinery. Use wet or dry. ENFLEX PADS 3” / 4” / 5” x 60grit en60elfleX 3” / 4” / 5” x 120grit en120elfleX These polishing discs are specifically designed for heavy 3” / 4” / 5” x 220grit en220elfleX stock removal applications.We manufacture these with 3” / 4” / 5” x 400grit en400elfleX a fully exposed diamond surface. Perfect for grinding 3” / 4” / 5” x 800grit en800elfleX materials such as granite, marble, terrazzo, glass and 3” / 4” / 5” x 800grit (Metal) en800elfleXM composites. Use on hand held or floor machinery. Velcro 3” / 4” / 5” x 1800grit en1800elfleX backing. 3” / 4” / 5” x 7500grit en7500elfleX Use wet or dry. EN HAND PADS 4” x 60grit en60hAndpAd 4” x 120grit en120hAndpAd The perfect tool for that high polish when no power 4” x 220grit en220hAndpAd tools are available. These aggressive pads work fast and 4” x 400grit en400hAndpAd effectively. The pads are 4” x 2” in size and contoured to 4” x 800grit en800hAndpAd fit comfortable in ones hand. Available in ogee & bullnose 4” x 800grit (Metal) en800hAndpAdM profiles. 4” x 1800grit en1800hAndpAd Grit sizes: 60 Green / 120 Black / 220 Red / 400 Yellow / 4” x 7500grit en7500hAndpAd 800 White / 1800 Blue 30 CALL FOR QUANTITY DISCOUNTS
- 31. SURFACE PREPARATION BEVELING TOOLS Beveling Router geotechroUter GEOTECH ROUTER A powerful, newly designed and easy to use shaping & beveling tool. The arbor fits 5/8-11 threaded or regular profile wheels. Equipped with a quick connect water feed attachment. Also built-in easy glide roller feet for a friction free smooth operation roll. Designed to easily grind marble, granite and all natural stone. The 115V DeWalt motor will provide years of trouble free service. Tool changing is a snap. SHAPING WHEELS These long life profile milling routers are engineered to produce profile and contour shapes with ease. For shaping of granite, marble and natural stone. Designed for use with Marmo, Ghines and other portable routers. CALL FOR SIZES Wheels consist of holding arbor, thrust and contact rings. Grinding surface available in Segmented/Sintered (pos 1) & Brazed (pos 2&3). Profile Position: Full Bullnose, 1, 2, 3: Half Bullnose, 1, 2, 3: Ogee, 1, 2, 3. Select desired cut shape from chart below. 6” x .375” 6.375lkprofwheel DIAMOND PROFILE 6” x .500” 6.5lkprofwheel These premium 6 inch 1/2 bull profile wheels are brazed with a course grit. Designed to profile 3/8” or 1/2” granite tile, porcelain tile, marble and natural stone. This unique design can cut and shape at the same time. Fits all tile OTHER SIZES saws. AvAILABLE ! *ogee shape available upon request SH A PE A SH A PE E SHAPE L SHAPE P SHAPE T “ EA SE D ” 4 5 D E G REE B E V E L “SCOT I A CO V E” Cove Demi A Eased E 45º Bevel L Cove P T Cove Demi Scotia Scotia Eased SH A PE F A Demi “OGEE” L P Scotia T Eased Ogee F SH A PE B SHAPE M SHAPE Q SHAPE U “DE M I B U L L N OSE ” “STA I R T R E A D ” Demi Shape Q SH A PE G Stair B M Q U Shape U Shape G G SH A PE C “ B IRD ’ S B E A K ” SHAPE V SHAPE N SHAPE R SH A PE H “FULL BULLNOSE” Demi “ D U PON T ” C Demi Shape R Dupont N Cove R V H SH A PE D Shape D SH A PE I SHAPE Z D “NORMANDY BEAD ” SHAPE O SHAPE S “STRAIGHT ” Dupont Shape O Cove Z Bit 30º Bevel I O S Demi Z D* Dupont = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 31
- 32. MISCELLANEOUS TOOLS MILLING & DRILLING EPTWIST 0.187” 3/16eptwiSt 0.218” 7/32eptwiSt These specially engineered diamond bits are designed 0.250” 1/4eptwiSt to drill and bore fast clean holes through natural and 0.375” 3/8eptwiSt composite materials. 1/4” shank. 0.500” 1/2eptwiSt W/D CHCOREDRILL 0.125” 1/8chcoredrill 0.187” 3/16chcoredrill These specially engineered diamond bits are designed 0.250” 1/4chcoredrill to drill and bore fast clean holes through natural and 0.312” 5/16chcoredrill composite materials. 1/4” shank. 0.375” 3/8chcoredrill Perfect for porcelain and includes extractor. 0.500” 1/2chcoredrill W/D FINGER BIT 1” x 2” x 1/2 gas 1hkfingerbit Segmented finger bits engineered with bottom segment for plunge cutting. Designed to work with CNC equipment for fast high speed removal rate with this quality diamond tool. Ideal for marble, granite and all natural stone. W/D ZERO TOLERANCE DRUM WHEEL VACUUM BRAZED 2” x 2” - 30/40 Grit 2ln40drUM Aggressive cutting and rapid stock removal action for 2” x 2” - 50/60 Grit 2ln60drUM use on handheld machines. Provides a smooth finish for 3” x 2” - 30/40 Grit 3ln40drUM an easy final polish. Excellent quality for working with 3” x 2” - 50/60 Grit 3ln60drUM granite, marble and natural stone. STANDARD BRAZED 2” x 2” - 30/40 Grit 2ln40SdrUM W/D 2” x 2” - 50/60 Grit 2ln60SdrUM 3” x 2” - 30/40 Grit 3ln40SdrUM 3” x 2” - 50/60 Grit 3ln60SdrUM Threaded = 5/8”-11 32 CALL FOR QUANTITY DISCOUNTS
- 33. SYNTHETIC SURFACE ENGINEERED STONE Call for Sizes SheStUrbo ENGINEERED STONE TURBO Our Engineered Stone Turbo diamond blades are specifically design for engineered stone surfaces. The blade core and high diamond quality make this the best choice for this type of cutting application. This blade CALL FOR DETAILS gives excellent life and fast cuts. Cuts granite, engineered stone and other similar synthetic surfaces. Call for Sizes SheSlgS ENGINEERED STONE SILENT Our Engineered Stone Silent Core diamond blades are specifically design for engineered stone surfaces. The blade core and high diamond quality make this the best choice for this type of cutting application. This blade CALL FOR DETAILS gives excellent life and fast cuts. Cuts granite, engineered stone and other similar synthetic surfaces. Call for Sizes SheSfingerbit ENGINEERED STONE FINGER High quality segmented finger bits engineered with bottom segment for plunge cutting. Designed to work with CNC equipment for fast high speed removal rate with this quality diamond tool. Cuts granite, engineered CALL FOR DETAILS stone and other similar synthetic surfaces. 4.8 Volt w/ Charger kwikdriVe KWIK DRIvE Cordless Palm Screwdriver • Lightweight • High Impact Body • Ni-Cad Battery • 200 RPM • Forward / Reverse Switch • Magnetic Chuck Includes: #2 Phillips bit Flathead bit Quick Charger = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 33
- 34. INTERNATIONAL LINE POWER TOOLS High quality diamond blades designed for the Export & Domestic market where value is a plus. All blades are skin packed for high visibility display & fast turn sales. Sold in case pack only. SEGMENTED - 7MM SEGMENTED - 7MM SEGMENTED & TURBO - 10MM Sizes: 4”, 4.5”, 7”, 9” Sizes: 4”, 4.5”, 7”, 9” Sizes: 4”, 4.5”, 7”, 9” TURBO - 7MM CONTINUOUS RIM - 7MM & 10mm SEGMENTED - 10MM Sizes: 4”, 4.5”, 7”, 9”, 12”, 14” Sizes: 4”, 4.5”, 7”, 9”, 12”, 14” Sizes: 9”, 12”, 14” We Handle A Full Line Of Diamond Cutting Saws. Call for Availability. NO DUST A portable water system with fitting for handheld saws. 3 Gallon capacity • 10ft - 5/8 Hose • Gardena Quick Connect 34 CALL FOR QUANTITY DISCOUNTS
- 35. CARBIDE BLADES WOOD, ALUMINUM & STEEL 7.25” x 24 Tooth 7.25cArbide24 RENEGADE I 7.25” x 40 Tooth 7.25cArbide40 RENEGADE I™ M2 carbide tipped blade’s are 8.25” x 24 Tooth 8.25cArbide24 8.25” x 40 Tooth 8.25cArbide40 manufactured for high performance. The blade’s teeth 10” x 40 Tooth 10cArbide40 are tipped with long life M2 carbide providing excellent 10” x 60 Tooth 10cArbide60 blade service. 10” x 80 Tooth 10cArbide80 • High performance Do-It-Yourself quality • M2 carbide for long blade life • Thin kerf design for smooth fast cutting • Precision expansion slots for cooling • 6X more durable due to reinforced shoulders All Blades Skin Packed Cuts all types of wood, plywood, particle board, chipboard, wallboard and plastics. 7.25” x 24 Tooth 7.25renegAde324 RENEGADE III 7.25” x 40 Tooth 7.25renegAde340 RENEGADE III™ C3 carbide tooth blades are manufactured to 8.25” x 24 Tooth 8.25renegAde324 exacting specifications. The blade’s teeth are tipped with extra 8.25” x 40 Tooth 8.25renegAde340 strong C3 carbide, providing many more cuts per board foot. 10” x 40 Tooth 10renegAde340 • Professional Series 10” x 60 Tooth 10renegAde360 • Higher running speeds due to diamond sharpened teeth 10” x 80 Tooth 10renegAde380 • C3 carbide for longer blade life 12” x 60 Tooth 12renegAde360 • Thin kerf design for smooth fast cutting 12” x 80 Tooth 12renegAde380 • Precision expansion slots for cooling & warpage 14” x 60 Tooth 14renegAde360 prevention 14” x 80 Tooth 14renegAde380 • 15X more durable for top notch performance All Blades Skin Packed Cuts all types of wood, plywood, particle board, chipboard, wallboard and plastics. 4.375” x 24 Tooth renS43t24 RENEGADE S 5.375” x 30 Tooth renS53t30 These NEW Renegade’s are engineered to cut through 6.5” x 40 Tooth renS65t40 7.25” x 56 Tooth renS72t56 metals quickly and smoothly. The unique quality of 9” x 48 Tooth renS09t48 carbide, tooth strength and angle make for a superior 10” x 60 Tooth renS10t60 product that performs effortless, cut after cut. Perfect 12” x 80 Tooth renS12t80 for steel sheeting/siding. Works with most professional 14” x 90 Tooth renS14t90 quality cold saws. Tooth height 5mm and a thickness of 2mm. All Blades Skin Packed 4.375” x 40 Tooth renA40t40 RENEGADE A 5.375” x 30 Tooth renA53t30 These NEW Renegade’s are engineered to cut through 6.5” x 80 Tooth renA65t80 7.25” x 40 Tooth renA72t40 metals quickly and smoothly. The unique quality of 10” x 60 Tooth renA10t60 carbide, tooth strength and angle make for a superior 12” x 80 Tooth renA12t80 product that performs effortless, cut after cut. Perfect for 14” x 100 Tooth renA14t100 aluminum sheeting/siding. Works with most professional quality cold saws. Tooth height 5mm and a thickness of 2mm. All Blades Skin Packed = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 35
- 36. CONCRETE FLOOR SOLUTIONS ® All Dyes Are EARTH FRIENDLY AMERIPOLISH Polish Concrete Dyes AMERIPOLISH is a translucent dye that is formulated using extremely fine molecules of color designed to penetrate and color any cementious surface. (All bond barriers must be removed prior to application of dye). AmeriPolish Dye was created for use with polished concrete, but can be used as a base color or touch up for concrete that has received integral color, dry shake hardeners, acid stains or even as highlight. NOW AVAILABLE In Both Solvent & Water-Based AMERIPOLISH - WATER-BASED Dye offers the same 22 colors as the original Solvent-Based dye with just as much vibrancy. Key markets are for projects where air flow cannot be safely controlled, where electrical spark or flames are present, and where your project involves working around fresh meat, vegetables and fruit. EDGETINT is a mixture of AmeriPolish dye and our proprietary acrylic blend that allows you to apply color that is complementary or contrasting to your field color, at edges, footing and hard to reach areas, or areas where you are unable to grind or polish. As with any sealer application, it is recommended that you apply a wax coat if the work is in a traffic area. dYe-n-SeAl eXterior AMeripoliSh concrete dYe SYSteM SMOOTH FINISH SURFACE: PRODUCT SIZE COVERAGE RATE PRODUCT SIZE COVERAGE RATE 6 oz. 20 Sq. Ft. 6 oz. 20 Sq. Ft. 1 Gallon 400-600 Sq. Ft. 1 Gallon 400-600 Sq. Ft. 5 Gallon 2,000-3,000 S.F. 5 Gallon 2,000-3,000 S.F. enhAncerpro™ edgetint POROUS SURFACE: PRODUCT SIZE COVERAGE RATE PRODUCT SIZE COVERAGE RATE 6 oz. 20 Sq. Ft. 6 oz. 8 Sq. Ft. 1 Gallon 400-600 Sq. Ft. 1 Gallon 150-200 Sq. Ft. 5 Gallon 2,000-3,000 S.F. 5 Gallon 750-1,000 S.F. enhAncerpro™ penetrAting Agent dYe-n-SeAl® 400 SprAYAble SeAler PRODUCT SIZE COVERAGE RATE 20 oz. Bottle 4 oz. (per 1 gal. of mixed dye) PRODUCT SIZE COVERAGE RATE 1 Gallon 250-300 Sq. Ft. progUArd™ StAin Shield 5 Gallon 1,250-1,500 S.F. PRODUCT SIZE COVERAGE RATE 1 Gallon 2,000-2,500 Sq. Ft. dYe-n-SeAl interior - pro 5 Gallon 10,000-12,500 S.F. PRODUCT SIZE COVERAGE RATE progUArd™ conditioning cleAner 6 oz. 20 Sq. Ft. 1 Gallon 400-600 Sq. Ft. PRODUCT SIZE COVERAGE RATE 5 Gallon 2,000-3,000 S.F. 5 Gallon 1 oz. / Per 1 gallon of water * Now available for exterior applications 36 CALL FOR QUANTITY DISCOUNTS
- 37. CONCRETE FLOOR SOLUTIONS ® COLOR Chart Polished Concrete Polished Concrete Polished Concrete Polished Concrete Photos courtesy of American Concrete Concepts Springdale, AR EdgeTint EdgeTint EdgeTint EdgeTint gold rAw SiennA cArAMel SAnd Polished Concrete Polished Concrete Polished Concrete Polished Concrete EdgeTint EdgeTint EdgeTint EdgeTint terrA cottA MAhogAnY SAddle brown chocolAte brown Earth Friendly All dYeS Are Polished Concrete Polished Concrete Polished Concrete Polished Concrete EdgeTint EdgeTint EdgeTint EdgeTint wAlnUt bUrnt SiennA cheStnUt MAroon Polished Concrete Polished Concrete Polished Concrete Polished Concrete EdgeTint EdgeTint EdgeTint EdgeTint SepiA eggplAnt pAtriot blUe tUrQUoiSe Polished Concrete Polished Concrete Polished Concrete Polished Concrete EdgeTint EdgeTint EdgeTint EdgeTint SlAte blUe green pine green foreSt green Polished Concrete Polished Concrete 22 EdgeTint Midnight blAck EdgeTint blAck Vivid Colors. These color samples are only a representation of the AmeriPolish Dye colors. Change in concrete slab colors will effect the appearance of the dye. Color results cannot be guaranteed, actual colors may vary. = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 37
- 38. CONCRETE FLOOR SOLUTIONS 38 CALL FOR QUANTITY DISCOUNTS
- 39. CONCRETE FLOOR SOLUTIONS = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 39
- 40. CONCRETE FLOOR SOLUTIONS kemiko KEMIKO Stone Tone Stain transforms an ordinary concrete slab into a luxurious floor that resembles marble or glazed stone. When concrete is stained and scored Kemiko creates the appearance of expensive flooring at a fraction of the cost. This stain is an acid base, single component product that provides a decorative, low maintenance floor finish and is 0-VOC. This class product contains special wetting agents, which chemically combine metallic ions with the particles in the concrete to form colored oxides. Kemiko Stone Tone Stain is the perfect choice for interior and exterior projects. Unlike paint, Kemiko Stone Tone Stain reacts with the minerals present in the concrete giving it the look and feel of natural stone. Whether working with a neoclassic, Southwestern, eclectic, or traditional décor, Stone Tone Stain adapts to enhance any setting. COLOR CHART KEMIKO Concrete Stain REMBRANDT Polymer Stains Stone Tones Base Colors tweed white Sand Adobe oyster black Standard Colors burnt Sienna burnt Umber Med. Yellow Monoazo red orange phthalo blue phthalo green raw Sienna raw Umber Yellow oxide Violet red oxide 40 CALL FOR QUANTITY DISCOUNTS
- 41. CONCRETE FLOOR SOLUTIONS kemiko Transforms an ordinary concrete slab into a luxurious floor that resembles marble or glazed stone. When concrete is scored and stained, Kemiko creates the appearance of expensive flooring at a fraction of the cost. Whether working with a neoclassic, Southwestern, eclectic, or traditional décor, Stone Tone Stain adapts to enhance any setting. Part Number Size Kemiko® Neutra Clean Neutra Clean 1 gal. An industrial strength, high performance water base sodium metasilicate cleaner for the preparation of bare concrete for staining, sealing, and recoating. It is a water viscosity, single component product with a pleasant citrus odor that does not contain any hazardous solvents and is highly recommended as a product to neutralize the residue and clean the concrete surface after staining. Kemiko® Stone Tone Acid Stain Stone Tone Stain 1 gal. Decorative, low maintenance acid stain with 0-VOC. Forms permanent colors on concrete. 5 gal. Can be applied either to interior or exterior concrete. Exterior vertical and horizontal application is possible, such as, concrete walls of buildings, retaining walls, sound barriers, driveways, and patios. Interior applications include concrete floors and counter tops in kitchens, living, dining and recreation areas, as well as, commercial applications such as hallways, walkways, stadiums, casinos, rockwork, and statuary. Available in eight colors. Kemiko® Stone Tone Wax II (Buff On) Stone Tone Buff On Wax 1 gal. This is a specially formulated buff on wax for concrete that produces a low sheen finish with (clear) 5 gal. very high protection and durability. Designed for interior use over Kemiko Stone Tone Stain, colored concrete, tile, brick, or any masonry surface. Kemiko® Stone Tone Sealer II Stone Tone Sealer II 1 gal. A high performance waterborne, water viscosity, low VOC, single component acrylic urethane (gloss & satin) 5 gal. polymer sealer that is very user friendly and is designed to provide resistance to water, alkali, acids, UV light, and staining. The product is a non-yellowing concrete floor coating available in clear gloss and satin finish. Kemiko® Sta Natural STA Natural 1 gal. A single component 0-VOC waterborne siloxane emulsion used to improve the water resistance of Kemiko stained concrete. It is an extremely user friendly product that repels water, reduces efflorescence and frost damage while allowing the substrate to breath. Kemiko® Easy Shine Wax (Mop On) Easy Shine Mop On Wax 1 gal. A low-VOC, extremely user friendly, waterborne acrylic polymer, mop on wax for protecting and maintaining sealed concrete and many other finished substrates. Easy Shine repels water, reduces scuffing and marring, allows substrate to breathe, is low odor, and produces a deep rich shine. Kemiko® Easy Strip Easy Strip 1 gal. A high performance water base, concentrated wax stripper designed for easy removal of Kemiko Stone Tone and Easy Shine waxes. Does not contain hazardous solvents. Is biodegradable. Sta Crete® Abrasion & chemically resistant waterborne epoxies, polyurea/ polyurethanes, and Sta-Crete 1600 1.3 gal. kit 100% solids coatings. Epoxy patching compounds. Excellent leveling, high gloss finishes. Sta-Crete 2700 1.25 gal. kit Clear and pigmented. Recommended for corrosive environments, food related businesses, Sta-Crete 3700 1 gal. kit aircraft hangars, showrooms, maintenance bays, warehouses and general manufacturing floors. Various products for use on wood, concrete, steel. Chemical containment areas. Quick cure primers, 100% solids epoxies & polyureas, and high solids polyurethanes. Most are zero or ultra low VOC. Little to no odor Kemiko® Stone Tone Acid Stain (Concrete Stains) Concrete Stains 1 gal. 1 Qt. Decorative, low maintenance acid stain with 0-VOC. Forms permanent colors on concrete. Colors: Cola, Aqua Blue, Golden Wheat, Can be applied either to interior or exterior concrete. Exterior vertical and horizontal application Vintage Umber, Malay Tan, Black, English is possible, such as, concrete walls of buildings, retaining walls, sound barriers, driveways, Red, Green Lawn and patios. Interior applications include concrete floors and counter tops in kitchens, living, dining and recreation areas, as well as, commercial applications such as hallways, walkways, stadiums, casinos, rockwork, and statuary. Available in eight colors. Rembrandt (Polymer Stains) Polymer Stains 1 gal. 1 Qt. Ultra-low VOC, acrylic polymer stain. Excellent adhesive strength and wear qualities. A full Base Colors: Tweed, Sand, Oyster, White, palette of pigments that allow the applicator to decorate concrete with an unlimited variation of Adobe, Black artful colors. Applied to walkways, decks, commercial and residential floors, hospitals, schools, Standard Colors: Burnt Sienna, Orange, malls, restaurants, interior or exterior concrete, plaster, polymer cement, as well as, applications Med. Yellow, Phthalo Green, Raw Umber, to wood as a stain, wash, or faux finish. Violet, Burnt Umber, Monoazo Red, Phthalo Blue, Raw Sienna, Yellow Oxide, Red Oxide = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 41
- 42. CONCRETE FLOOR SOLUTIONS Lythic™ Solutions for Polished Concrete The Difference in Densifiers™ Lythic™ is the easiest way to harden and densify concrete: • 15-minute spray-on application • 1-hour set time – no overnight waiting • No residue removal or hazardous waste disposal • Reduced labor costs • Improved surface hardness and density • Top-quality polishing results Why Colloidal Silica? The Colloidal Silica in Lythic penetrates quickly, deeply, and cleanly into concrete. The nano-size particles are highly reactive in concrete. They form cementious compounds that harden and densify the surface with less wait and less waste. A Sustainable Shine Conventional densifiers are silicate-based products; they are highly caustic, difficult to handle, and form chemical by- products that require disposal as a hazardous material. Lythic Densifier, however, has a lower pH; it is safer to handle, penetrates concrete quickly, and does not leave a dangerous residue. Lythic Densifier has zero VOCs and contains no harsh chemical solvents. Hard Made Easy™ Lythic Densifier does not have to be scrubbed into the surface, and it does not produce a slurry or gel that has to be scrubbed off. And since there is no residue to remove, there is no need to rinse the surface after treatment, and no waste disposal problem. Lythic™ Densifier Lythic™ Cleaner Lythic™ Protector Our Colloidal Silica formula eliminates is Periodic cleaning with Lythic Cleaner Use Lythic™ Protector after polishing so fast acting that polishing can begin not only cleanses the concrete, but concrete. It contains Colloidal Silica to just one hour after Lythic application, adds extra Colloidal Silica to the further densify the floor, plus polymers often allowing complete same-day surface. Lythic Cleaner fortifies as it that enhance the appearance of colored densifying and polishing. This translates cleans, with no rinsing required. Use it concrete, improve stain resistance, and into savings on labor, equipment, and as part of regular building maintenance defend the slab against mild acids such disposal costs. Lythic gets the job done for maximum value. as my be encountered in places where sooner, speeds construction schedules, food is handled or served. and minimizes business disruptions in existing facilities. Order No. Order No. Order No. L-DENSIFIER 5 gal. L-CLEANER 5 gal. L-PROTECTOR 5 gal. L-DENSIFIER 55 gal. L-CLEANER 55 gal. L-PROTECTOR55 gal. 42 CALL FOR QUANTITY DISCOUNTS
- 43. CONCRETE FLOOR SOLUTIONS Amano Pioneer Eclipse® Is the world leader in Ultra High Speed (UHS) FloorCare Propane Burnishers, Battery Burnishers and Electric Buffers, Automatic Scrubbers, Stripping Machines, as well as a full line of Cleaning and Sanitation Chemical Products. MEAN MACHINE - UHS Propane Burnisher with Dust Collector: The ULTIMATE VALUE PROPOSITION - quality, safety and performance now enhanced with an excellent dust collection system. • 585 cc OHV v-valve Kawasaki engine • The 28” has a powder-coated, cast aluminum alloy deck • Performance: 34,000 (+or- 3160m2) sq ft per hr • CentriVac Dust Collection System with innovative skirt design • Catalytic muffler to minimize emissions • 12V battery start • RokBak deck for easy-access pad installation from standing position • Electric clutch stops pad rotation when lever is released • EcoSense Emission monitoring optional CLEAN STAR 20 Scrubbing rate: 18,800 ft2/hr (1750 m2/hr) Maximum cleaning width: 19.7 in (500 mm) Battery Powered Autoscrubber Squeegee width: 29 in (740 mm) FEATURES: Solution tank capacity: 12 US gal (45 liter) • Large capacity tanks require less frequent Recovery tank capacity: 12 US gal (45 liter) filling & emptying Vibration level: Less than 2.5 m/s2 • Ultra slim profile Pad/brush motor: 370w, 17a • 2-3 hour run time, easy access batteries Traction motor: 100w, 8a • Traction drive for ease of operation Vacuum motor: 550w, 22a • Highly maneuverable Batteries: 2 x 12V, 100 amp-hr Weight with batteries: 308 lb (140 kg) • Quick and easy pad or brush replacement Length x width x height: • User-friendly instrument panel 39.4 in x 21.7 in x 41.7 in • Adjustable pad/brush pressure (100 cm x 55 cm x 106 cm) • CE approved POWER STAR Z1 Scrubbing rate 33,000 ft2/hr - 3066 m2/hr Propane Powered Scrubber Cleaning width 33” / 84 cm Pads/brushes 2 x 17 in / 43 cm EXCEPTIONAL PERFORMANCE Squeegee width 42 in / 107 cm • Propane power offers unlimited run-time with no Scrub pressure 120-250 lb / 55-113.5 kg down time for recharging batteries Solution & Recovery tank capacities • Large capacity tanks require less frequent filling 35 US gal / 132.5 liter & dumping Engine: Kawasaki 437 cc liquid-cooled • Regenerative blower technology for water pick- Engine speed: 3500 RPM up Brush motor: 2 hydraulic motors, 200 rpm • Adjustable brush/pad pressure offers optimal Pump: Dual hydraulic pump Vacuum fan flexibility in different applications Noise level: <80 dBA • Brushes/pads & solution flow stop automatically Vibration level: Less than 2.5 m/s2 when accelerator is released Weight w/cylinder: 860 lb / 390 kg • Squeegee raises automatically when machine Length x width x height goes into reverse 66 in x 26 in x 46.5 in • Large clean-out port on recovery tank provides 168 cm x 66 cm x 118 cm quick and easy clean-up • Easy operation includes user-friendly controls, automatic braking, and emergency stop • Proprietary drive system provides ultra-smooth operation & no belts, no chains & no adjustments • Durable construction with industrial components yields long life = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 43
- 44. CONCRETE FLOOR SOLUTIONS What makes WerkMaster™ so unique? Octi-Disc™ Technology and SPEED! Our heads spin at disc speeds that are unheard of in the industry and unavailable on a planetary! Think of a variable speed hand grinder – the faster your RPM, the FASTER the Rate of Removal! We have eight heads spinning at up to 3000 RPM that produce the fastest Rate of Removal in the industry without using heavy weight kits! WerkMaster’s are fast, tough and agile, voraciously tearing into concrete, thin set, spalled or rained out concrete, VCT glue, VAT glue, rubber back carpet residue, mastic, epoxy, paint and virtually any surface you can throw at them, while delivering superior results and Rates of Removal that most competitors only dream of achieving! Tradesmen are amazed and delighted with the ease of use and total customer satisfaction achieved with a WerkMaster™. The tankless water feature allows both wet and dry grinding and polishing. Combining Octi-Disc™ Technology with the WerkMaster Pulse-Bac® vacuum system will deliver a 100% Airborne Dust and Allergen Free environment. Fast, agile, easy and fun to operate, test drive a WerkMaster™ and see how quickly you too can improve your bottom line profits! WerkMaster – Taking it to the Wall! ADVANTAGES Versatile – The same machine can grind, edge and buff any concrete surface with just a simple quick change of discs. FAST – From 2000 to 3000 RPM of High Speed Grinding, edging, polishing and buffing. Innovative Design – The WerkMaster’s patent-pending Octi-Disc™ design allows the machine to go right under cabinets and within 1/8” of the wall virtually eliminating the need for edgers. Dust Free – The WerkMaster™ is 100% Dust Free when utilizing our WerkMaster™ Pulse-Bac Vacuum System or any approved commercial vacuum system. Concrete Polishing System – Only No. 1400 - EUROPA - ( 4-3/4” Tooling) WerkMaster™ offers a proprietary concrete polishing system utilizing our No. 2400 - COLOSSOS- ( 6-3/4” Tooling) patent pending DG – Diamond Abrasives that deliver results that no other machine can match. Ease of Use – The WerkMaster™ can be operated with minimal effort and requires very little training. Low Maintenance – Contractors will enjoy the benefits of the WerkMaster’s superior quality and low maintenance features. Fab-u-Floors – An independent subsidiary of Werk Industries, Fab-u-Floors was developed to operate as WerkMaster’s Research and Development division, providing invaluable feedback from the field and allowing management to have hands on experience with the machines in all types of situations. This experience is passed on to you as a WerkMaster No. 1800 - TITAN - ( 5-3/4” Tooling) No. V270 - WERKMASTER PULSE-VAC customer. 44 CALL FOR QUANTITY DISCOUNTS
- 45. CONCRETE FLOOR SOLUTIONS Concrete Metal Bond Abrasives Surface Preparation 4 Segmented Steel Diamonds Disc: 020-0063-00 4-3/4” 4-BAR 20 GRIT X-SOFT 020-0066-00 4-3/4” 4-BAR 20 GRIT SOFT 020-0065-00 4-3/4” 4-BAR 20 GRIT MEDIUM 020-0064-00 4-3/4” 4-BAR 20 GRIT HARD PolyCrystalline Diamond (PCD) Disc: 020-0141-00 5-3/4” 4-BAR 20 GRIT X-SOFT 020-0144-00 5-3/4” 4-BAR 20 GRIT SOFT 020-0074-00 4-3/4” RIPPER 3 SEG PCD 020-0143-00 5-3/4” 4-BAR 20 GRIT MEDIUM 020-0152-00 5-3/4” RIPPER 3 SEG PCD 020-0142-00 5-3/4” 4-BAR 20 GRIT HARD 020-0218-00 6-3/4” RIPPER 3 SEG PCD 5 Segmented Steel Diamonds Disc: 020-0210-00 6-3/4” 5-BAR 20 GRIT X-SOFT 020-0213-00 6-3/4” 5-BAR 20 GRIT SOFT Surface Preparation 020-0212-00 6-3/4” 5-BAR 20 GRIT MEDIUM 020-0211-00 6-3/4” 5-BAR 20 GRIT HARD METAL FLEX PADS (CONCRETE) Disposable Wet/Dry Resin Pads 003-0016-00 4-3/4” DLX RESIN 30 GRIT 003-0017-00 4-3/4” DLX RESIN 50 GRIT CONCRETE DIAMOND PADS 003-0018-00 4-3/4” DLX RESIN 100 GRIT 003-0019-00 4-3/4” DLX RESIN 200 GRIT 002-0471-00 4-3/4” Metal Flex Pads 30 GRIT (Soft) 003-0020-00 4-3/4” DLX RESIN 400 GRIT 002-0470-00 4-3/4” Metal Flex Pads 30 GRIT (Medium) 003-0021-00 4-3/4” DLX RESIN 800 GRIT 003-0022-00 4-3/4” DLX RESIN 1500 GRIT 002-0473-00 4-3/4” Metal Flex Pads 60 GRIT (Soft) 003-0023-00 4-3/4” DLX RESIN 3000 GRIT 002-0472-00 4-3/4” Metal Flex Pads 60 GRIT (Medium) 003-0024-00 5-3/4” DLX RESIN 30 GRIT 002-0467-00 4-3/4” Metal Flex Pads 150 GRIT (Soft) 003-0025-00 5-3/4” DLX RESIN 50 GRIT 002-0466-00 4-3/4” Metal Flex Pads 150 GRIT (Medium) 003-0026-00 5-3/4” DLX RESIN 100 GRIT 003-0027-00 5-3/4” DLX RESIN 200 GRIT 002-0471-00 4-3/4” Metal Flex Pads 300 GRIT (Soft) 003-0028-00 5-3/4” DLX RESIN 400 GRIT 002-0470-00 4-3/4” Metal Flex Pads 300 GRIT (Medium) 003-0029-00 5-3/4” DLX RESIN 800 GRIT 003-0030-00 5-3/4” DLX RESIN 1500 GRIT 002-0487-00 5-3/4” Metal Flex Pads 30 GRIT (Soft) 003-0031-00 5-3/4” DLX RESIN 3000 GRIT 002-0486-00 5-3/4” Metal Flex Pads 30 GRIT (Medium) 003-0032-00 6-3/4” DLX RESIN 30 GRIT 002-0489-00 5-3/4” Metal Flex Pads 60 GRIT (Soft) 003-0033-00 6-3/4” DLX RESIN 50 GRIT 002-0488-00 5-3/4” Metal Flex Pads 60 GRIT (Medium) 003-0034-00 6-3/4” DLX RESIN 100 GRIT 003-0035-00 6-3/4” DLX RESIN 200 GRIT 002-0483-00 5-3/4” Metal Flex Pads 150 GRIT (Soft) 003-0036-00 6-3/4” DLX RESIN 400 GRIT 002-0482-00 5-3/4” Metal Flex Pads 150 GRIT (Medium) 003-0037-00 6-3/4” DLX RESIN 800 GRIT 003-0038-00 6-3/4” DLX RESIN 1500 GRIT 002-0485-00 5-3/4” Metal Flex Pads 300 GRIT (Soft) 003-0039-00 6-3/4” DLX RESIN 3000 GRIT 002-0484-00 5-3/4” Metal Flex Pads 300 GRIT (Medium) = Blade Speed = Run Wet or Dry = Bond (pg. 2) CALL FOR QUANTITY DISCOUNTS 45
- 46. CONCRETE FLOOR SOLUTIONS PREP/MASTER #STI-3030 Ideal for polishing projects greater than 2,000sf • Versatile machine despite its weight and size Easy one man loading and un-loading • Easier to operate than planetary gear machines The operator doesn’t fi ght the machine - He runs it! • Moveable weight system for multiple applications Variable speed drive for unlimited speed variation Production Rates of the STI-3030 Prep/Master® STI-3030 Prep/Master® Ideal for polishing projects greater than 10,000 Sq. Ft. Mastic removal rates of 500 Sq.Ft. per hour Thin Set removal rates of 500 Sq Ft. per hour Mil coatings removal of 200 Sq. Ft. per hour Concrete polishing rates of 1,100 Sq. Ft. per hour/per step Specifications Motor 30h.p. 3 phase Power Source 230 VAC 3 phase 60Hz Current 56 amps soft start Motor RPM 2625 @ 90Hz Power Cord 25 feet (4-4) Vacuum Hose 2” x 25’ x Two Weight 1,064lbs. Tool RPM 750rpm @ 90Hz Pressure on Tools 1010 w/weights Tools Available All Dimensions 81” L x 30” W x 50” H Cleaning Path 28” x 56” sweep S.T.I. Concrete Pads S.T.I. Concrete Diamond Wheel • For concrete & portland based terrazzo opening cut • Excellent scratch pattern for old & new concrete • Use for opening steps on uncoated concrete • Easy tool changes • Excellent scratch pattern for old or new concrete • Long lasting durability • Use dry • Use wet or dry • Velcro backed, for easy tool change • 6mm thickness • Diamonds set in metal-bond & resin-bond • available with hook & loop backing or pin • 8MM thickness • Fits many popular machines Grits available: 35, 50, 100 Grits available: 6, 16, 30, 70, 100, 200, 400 Diameter 3” & 4” order no. rM8MM - Specify grit & diameter order no. 10S - Specify grit 46 CALL FOR QUANTITY DISCOUNTS
- 47. TERMS INDEX iteM bond pAge iteM bond pAge iteM bond pAge ACCESSORIES, CORERIG . . . . . . . 22 EARLY ENTRY BLADES . . . . . . . . . 12 NO DUST . . . . . . . . . . . . . . . . 34 ADAPTERS . . . . . . . . . . . . . . . 22 ENELFLEX - PADS . . . . . . . . . . . 30 PADS-STI . . . . . . . . . . . . . . . . 46 AGGREGATE MAP . . . . . . . . . . . 14 ENGINEERED STONE BLADE . . . . . 33 PADS-WORKMASTER . . . . . . . . . 45 AIR POLISHER . . . . . . . . . . . . . 27 ENHANDPAD . . . . . . . . . . . . . . 30 PADS, POLISHING . . . . . . . . . . . 27-30 AMERIPOLISH. . . . . . . . . . . . . . 36-38 EPTWIST . . . . . . . . . . . . . . . . 32 PATRIOT . . . . . . . . . . . . . . . . . 39 ASPHALT BLADES . . . . . . . . . . . 11 ETORANGE15 . . . . . . . . . . . . . 3 9 PIONEER ECLIPSE . . . . . . . . . . . 43 ASPHCER . . . . . . . . . . . . . . . 4 11 FHBLKMAGIC - PADS. . . . . . . . . . 28 POWER SCREW DRIVER . . . . . . . . 33 CARBIDE BLADES . . . . . . . . . . . 35 FHTITAN . . . . . . . . . . . . . . . . 1 4 PRESTRESSED BLADES . . . . . . . . 12 CEREECUT . . . . . . . . . . . . . 1-4 12 FLOOR, CONCRETE SUPPLY. . . . . . 36-46 PRO1CC . . . . . . . . . . . . . . . . 2 13 CHASPH . . . . . . . . . . . . . . . . 4 11 FX . . . . . . . . . . . . . . . . . . 1-4 14 PRO2CC . . . . . . . . . . . . . . . . 3 13 CHCOREBIT . . . . . . . . . . . . . . 3 21 GACNCDUO . . . . . . . . . . . . . 2-4 9 PRO3ASPH . . . . . . . . . . . . . . 4 13 CHCOREDRILL . . . . . . . . . . . . . 32 GACOMBO12 . . . . . . . . . . . . 2/3 5/9 PRO4AOC . . . . . . . . . . . . . . . 3 13 CHDRYCOREBIT . . . . . . . . . . . 3 20 GASANDTP . . . . . . . . . . . . . . 2 19 PROFILE CHART . . . . . . . . . . . . 31 CHELECTROSEG . . . . . . . . . . . 4 17 GASANDTRIPTP. . . . . . . . . . . . 2 19 PROFILE WHEELS . . . . . . . . . . . 31 CHELSLOT . . . . . . . . . . . . . . 4 17 GATSEG12 . . . . . . . . . . . . . . 2 5 PROTECTOR, CONCRETE . . . . . . . 42 CHFANCUP . . . . . . . . . . . . . . 2 25 GATSEG12 . . . . . . . . . . . . . . 2 7 REDUCERS . . . . . . . . . . . . . . . 22 CHGRAN . . . . . . . . . . . . . . . 1 4/6 GATURBO12 . . . . . . . . . . . . . 3 3/7 RENEGADE BLADES . . . . . . . . . . 35 CHGRANQUAD . . . . . . . . . . . . 1 4 GBTP.250 . . . . . . . . . . . . . . . 3 19 RESCUE BLADE. . . . . . . . . . . . . 17 CHSAMURAI . . . . . . . . . . . . . 3 4 GEOTECH ROUTER . . . . . . . . . . . 31 ROOT . . . . . . . . . . . . . . . . C3 17 CHSUPERG . . . . . . . . . . . . . 2-4 10 GGSEG15 . . . . . . . . . . . . . . . 3 5 SEGPLATE, REP SEGS . . . . . . . . 2 26 CHSUPERGR . . . . . . . . . . . . 2-4 10 GGSEG15 . . . . . . . . . . . . . . . 3 8 SHAPING WHEELS . . . . . . . . . . . 31 CHTLSEC . . . . . . . . . . . . . . . 2 16 GGTURBO15 . . . . . . . . . . . . . 3 3 SHCNCSAND . . . . . . . . . . . . 1-3 15 CHTORNADO . . . . . . . . . . . . . 2 4/6 GTBACKPAD . . . . . . . . . . . . . . 27 SHCOREP . . . . . . . . . . . . . . . 3 21 CHTSEG12 . . . . . . . . . . . . . . 3 7 GTCRACK . . . . . . . . . . . . . . . 2 18 SHCOREPP . . . . . . . . . . . . . . 3 21 CLEANER, CONCRETE . . . . . . . . . 42 GTCROWN . . . . . . . . . . . . . 2-3 23 SHCOREPPF . . . . . . . . . . . . . 3 21 CNCGRANITE . . . . . . . . . . . . . 2 15 GTCUP . . . . . . . . . . . . . . . . 2 24 SHCRACK . . . . . . . . . . . . . . . 2 18 CNCRINGSAW . . . . . . . . . . . . 2 17 GTCUPSWIRL . . . . . . . . . . . . . 2 24 SHCRACKV . . . . . . . . . . . . . . 2 18 COLOR CHARTS . . . . . . . . . . . . 37-40 GTCUPSWIRL . . . . . . . . . . . . . 2 24 SHCROWN . . . . . . . . . . . . . 2-3 23 CORE BITS . . . . . . . . . . . . . . . 20-22 GTLION . . . . . . . . . . . . . . . . 1 10 SHCUP . . . . . . . . . . . . . . . . 2 24 CORE DRILL RIGS . . . . . . . . . . . 22 GTRINGSAW . . . . . . . . . . . . . 3 17 SHDRYCOREBIT . . . . . . . . . . . 3 20 CORERIG PLATE . . . . . . . . . . . . 22 GTTURBOCC . . . . . . . . . . . . . 2 24 SHDUCTILE . . . . . . . . . . . . . . 1 10 CRACK CHASERS . . . . . . . . . . . 18 HKALUMBACKPAD . . . . . . . . . . . 27 SHESLGS . . . . . . . . . . . . . . . . 33 CROWN BITS . . . . . . . . . . . . . . 23 HKASPH10 . . . . . . . . . . . . . . 4 11 SHESTURBO . . . . . . . . . . . . . . 33 CUP WHEELS . . . . . . . . . . . . . . 24-26 HKCONCDRY - PADS . . . . . . . . . . 29 SHGREEN . . . . . . . . . . . . . . . 4 11 DENSIFIER, CONCRETE . . . . . . . . 42 HKCONCDRYT - PADS . . . . . . . . . 29 SHHOTTLS . . . . . . . . . . . . . . 2 16 DIAMOND PAD-WORKMASTER . . . . 45 HKCRYSTALCUP . . . . . . . . . . . 2 26 SHHOTTSEGCUP . . . . . . . . . . . 2 25 DIAMOND WHEEL-STI . . . . . . . . . 46 HKDRYFLEX - PADS . . . . . . . . . . 29 SHHOTTURBOCC . . . . . . . . . . . 2 25 DIYEUROSEG10. . . . . . . . . . . . 3 5 HKECFLEX - PADS . . . . . . . . . . . 28 SHPRESTRESSED . . . . . . . . . 1-4 12 DIYEUROTURBO10 . . . . . . . . . . 3 3 HKFINGERBIT . . . . . . . . . . . . . . 32 SHTSEG15 . . . . . . . . . . . . . . 1 7 DIYSEGPB10 . . . . . . . . . . . . . 3 8 HKLTEARDROP . . . . . . . . . . . . 2 26 SHTURBOCC . . . . . . . . . . . . . 2 25 DIYSEGPB12 . . . . . . . . . . . . . 3 8 HKNEOPAD . . . . . . . . . . . . . . . 28 SHVANEBB15 . . . . . . . . . . . . . 3 9 DIYSEGRB. . . . . . . . . . . . . . . 3 8 HKPCDWHEEL . . . . . . . . . . . . 2 26 SHWAVE . . . . . . . . . . . . . . . . 1 3 DIYTPS . . . . . . . . . . . . . . . . 2 19 HKRIDGIDBACKPAD . . . . . . . . . . 27 SSSEGPLATE . . . . . . . . . . . . . . 26 DK CORERIGS . . . . . . . . . . . . . 22 HKSHINEPAD . . . . . . . . . . . . . . 28 STI . . . . . . . . . . . . . . . . . . . . 46 DMWEDGECUT . . . . . . . . . . . . 1 16 HKUCUP . . . . . . . . . . . . . . . 2 25 STJSLOT . . . . . . . . . . . . . . . 1 16 DRUM WHEEL. . . . . . . . . . . . . . 32/33 IDLGS . . . . . . . . . . . . . . . . . 2 15 STTLS . . . . . . . . . . . . . . . . . 1 16 DSLAMPO . . . . . . . . . . . . . . . 2 15 INTERNATIONAL BLADES . . . . . . . 34 SUPERG . . . . . . . . . . . . . . . 2-4 10 DSTWCORE . . . . . . . . . . . . . 2-3 23 JOTSEGPLATE . . . . . . . . . . . . . 26 TILE BLADES . . . . . . . . . . . . . . 16 DSWAVE-S . . . . . . . . . . . . . . 1 4 KEMIKO . . . . . . . . . . . . . . . . . 40/41 TUCK POINTERS . . . . . . . . . . . . 19 DTBRCOREBIT . . . . . . . . . . . 2-3 23 KFBACKPAD . . . . . . . . . . . . . . 27 VAC PUMP . . . . . . . . . . . . . . . 22 DTROSEX - PADS . . . . . . . . . . . . 29 KWIK DRIVE . . . . . . . . . . . . . . . 33 WERKMASTER . . . . . . . . . . . . . 44/45 DTTURBOCAT . . . . . . . . . . . . . . 30 LKVBCOREBIT . . . . . . . . . . . 2-3 23 WERKMASTER . . . . . . . . . . . . . 44/45 DTTYPHOON - PADS . . . . . . . . . . 30 LYTHIC . . . . . . . . . . . . . . . . . 42 ZERO TOLERANCE . . . . . . . . . . . 32 DUST SHROUD . . . . . . . . . . . . . 24 METAL CUTTING BLADES . . . . . . . 35 Recommended Maximum Diameter Operating Safe Speed [RPM] Speed [RPM] Hours Of Operation: 8:00 am to 5:00 pm EST. ades 4” 9,050 15,000 ing Depth 4.5” 8,050 13,300 Freight Policy: FOB warehouse, no freight charges on orders 5” 5” 7,250 12,000 7” 6” 6,050 10,150 over $1500.00 within continental USA. 8” 7” 5,180 8,730 8” 4,536 7,640 Return Policy: All returns must have a RA number (Return ades 9” 4,030 6,790 10” 3,625 6,115 Authorization) and subject to a 15% 1 3/4” 12” 3,020 5,095 2 2 1/4” 3/4” 12” HS [High Speed] 6,300 restocking fee. 14” 2,590 4,365 3 1/4” 3 3/4” 14” HS [High Speed] 5,400 Limited Warranty: All products are guaranteed against defects 16” 2,265 3,820 lades 16” HS [High Speed] 4,800 in material and workmanship for 1 year. The 18” 2,016 3,395 1” 20” 1,810 3,055 limited warranty does not cover improper or 1 1/4” 24” 1,510 2,550 1 1/2” 26” 1,395 2,350 negligent use. 2 1/2” 28” 1,295 2,185 3” 30” 1,210 2,040 Warranted products will be repaired or 32” 1,135 1,910 36” 1,010 1,700 replaced at the option of the company. 42” 864 1,455 48” 756 1,275 CALL FOR QUANTITY DISCOUNTS 47
- 48. We Handle AFull Line Of Saws & Core Drill Rigs Ask About Quantity Discounts 2150 SW 10th Street • Deerfield Beach, FL 33442 800-659-5843 Fax 954-570-6830 www.national-diamond.com “World Leader In Diamond Cutting Blades & Tools”