This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054C engine. The flywheel housing must first be supported with lifting equipment as it weighs approximately 39 kg. Setscrews securing the housing must be removed, and the housing can then be lifted off while tapping it with a soft hammer if needed. Cleaning and inspection steps are described before reinstalling the housing using setscrews, ensuring proper torque is applied.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...f8ioseoodkmmd
1. The document provides instructions for removing and installing a lifter group on a Caterpillar 3054C engine.
2. It lists the required tools which include a telescoping magnet.
3. The removal procedure involves first removing the camshaft, then using a magnet to remove the lifters from the cylinder block. Installation is the reverse of removal.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...fjkskkedmm4r
1. The document provides instructions for removing and installing a lifter group from a Caterpillar 3054C engine.
2. It lists the required tools which include a telescoping magnet.
3. The removal procedure involves first removing the camshaft, then using a magnet to remove the lifters from the cylinder block. Installation is the reverse of removal.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...a9ekdodkdkd
1. The document provides instructions for removing and installing a lifter group from a Caterpillar 3054C engine.
2. It lists the required tools which include a telescoping magnet.
3. The removal procedure involves first removing the camshaft, then using a magnet to remove the lifters from the cylinder block. Installation is the reverse of removal.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...onyvzcwadtu05
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) To remove the cylinder head, various components must first be removed including the fuel injectors, exhaust manifold, rocker shaft assembly, and glow plugs. The cylinder head is then lifted off using a lifting device.
2) When installing the new cylinder head, a clean cylinder head gasket is placed on dowels on the cylinder block. Guide bolts are used to help position the cylinder head, which is lifted into place.
3) Setscrews are installed and tightened in a specific numerical order to securely fasten the cylinder head.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...ze3xiandiao
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) To remove the cylinder head, various components must first be removed including the fuel injectors, exhaust manifold, rocker shaft assembly, and glow plugs. The cylinder head is then lifted off using a lifting device.
2) When installing the new cylinder head, a clean cylinder head gasket is placed on dowels on the cylinder block. Guide bolts are used to help position the cylinder head, which is lifted into place.
3) Setscrews are installed and tightened in a specific numerical order to securely fasten the cylinder head.
Caterpillar cat 249 d compact track loader (prefix gwr) service repair manual...fjjskefkskem
1. The document provides instructions for removing and installing a rocker shaft and pushrods on a Caterpillar C2.2 engine.
2. The procedure includes cleaning parts, installing a new seal on the rocker shaft, lubricating the pushrods and installing them, then lubricating the valve stems and installing caps before securing the rocker shaft assembly.
3. Steps are provided for installing the cylinder head, including cleaning surfaces, installing dowels and a new gasket, then tightening bolts in a specific sequence while using guide bolts and a degree wheel to ensure proper installation.
Caterpillar cat 249 d compact track loader (prefix gwr) service repair manual...fusjezsfkskefmsme
1) The document provides installation instructions for installing a rocker shaft and pushrods on a C2.2 engine. It describes cleaning parts, applying oil, inserting seals, nuts, and bolts in the correct positions and torques.
2) Removal instructions are provided for removing the cylinder head on a 4-cylinder C2.2 engine. It lists prerequisite removal steps and describes draining coolant, loosening bolts in reverse order, and lifting off the head using lifting devices.
3) Reinstallation instructions are provided for installing a cylinder head on a 4-cylinder C2.2 engine. It describes cleaning surfaces, inspecting for distortion, installing dowels and guide bolts, and
This document provides instructions for installing the cylinder head on a 4-cylinder engine. It includes:
1. Thoroughly cleaning the cylinder head and block mating surfaces.
2. Inspecting the cylinder head for distortion and replacing if needed.
3. Installing guide bolts into the cylinder block and using a degree wheel to ensure the cylinder head is parallel to the block.
4. Installing a new cylinder head gasket and dowels, and torquing the bolts in the correct sequence to specifications.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...f8ioseoodkmmd
1. The document provides instructions for removing and installing a lifter group on a Caterpillar 3054C engine.
2. It lists the required tools which include a telescoping magnet.
3. The removal procedure involves first removing the camshaft, then using a magnet to remove the lifters from the cylinder block. Installation is the reverse of removal.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...fjkskkedmm4r
1. The document provides instructions for removing and installing a lifter group from a Caterpillar 3054C engine.
2. It lists the required tools which include a telescoping magnet.
3. The removal procedure involves first removing the camshaft, then using a magnet to remove the lifters from the cylinder block. Installation is the reverse of removal.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...a9ekdodkdkd
1. The document provides instructions for removing and installing a lifter group from a Caterpillar 3054C engine.
2. It lists the required tools which include a telescoping magnet.
3. The removal procedure involves first removing the camshaft, then using a magnet to remove the lifters from the cylinder block. Installation is the reverse of removal.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...onyvzcwadtu05
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) To remove the cylinder head, various components must first be removed including the fuel injectors, exhaust manifold, rocker shaft assembly, and glow plugs. The cylinder head is then lifted off using a lifting device.
2) When installing the new cylinder head, a clean cylinder head gasket is placed on dowels on the cylinder block. Guide bolts are used to help position the cylinder head, which is lifted into place.
3) Setscrews are installed and tightened in a specific numerical order to securely fasten the cylinder head.
Caterpillar Cat CB-534D VIBRATORY COMPACTOR (Prefix C8M) Service Repair Manua...ze3xiandiao
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) To remove the cylinder head, various components must first be removed including the fuel injectors, exhaust manifold, rocker shaft assembly, and glow plugs. The cylinder head is then lifted off using a lifting device.
2) When installing the new cylinder head, a clean cylinder head gasket is placed on dowels on the cylinder block. Guide bolts are used to help position the cylinder head, which is lifted into place.
3) Setscrews are installed and tightened in a specific numerical order to securely fasten the cylinder head.
Caterpillar cat 249 d compact track loader (prefix gwr) service repair manual...fjjskefkskem
1. The document provides instructions for removing and installing a rocker shaft and pushrods on a Caterpillar C2.2 engine.
2. The procedure includes cleaning parts, installing a new seal on the rocker shaft, lubricating the pushrods and installing them, then lubricating the valve stems and installing caps before securing the rocker shaft assembly.
3. Steps are provided for installing the cylinder head, including cleaning surfaces, installing dowels and a new gasket, then tightening bolts in a specific sequence while using guide bolts and a degree wheel to ensure proper installation.
Caterpillar cat 249 d compact track loader (prefix gwr) service repair manual...fusjezsfkskefmsme
1) The document provides installation instructions for installing a rocker shaft and pushrods on a C2.2 engine. It describes cleaning parts, applying oil, inserting seals, nuts, and bolts in the correct positions and torques.
2) Removal instructions are provided for removing the cylinder head on a 4-cylinder C2.2 engine. It lists prerequisite removal steps and describes draining coolant, loosening bolts in reverse order, and lifting off the head using lifting devices.
3) Reinstallation instructions are provided for installing a cylinder head on a 4-cylinder C2.2 engine. It describes cleaning surfaces, inspecting for distortion, installing dowels and guide bolts, and
This document provides instructions for installing the cylinder head on a 4-cylinder engine. It includes:
1. Thoroughly cleaning the cylinder head and block mating surfaces.
2. Inspecting the cylinder head for distortion and replacing if needed.
3. Installing guide bolts into the cylinder block and using a degree wheel to ensure the cylinder head is parallel to the block.
4. Installing a new cylinder head gasket and dowels, and torquing the bolts in the correct sequence to specifications.
This document provides instructions for installing the cylinder head on a 4-cylinder engine. It includes:
1. Thoroughly cleaning the cylinder head and block mating surfaces.
2. Inspecting the cylinder head for distortion and replacing if needed.
3. Installing guide bolts into the cylinder block and using a degree wheel to ensure the cylinder head is parallel to the block.
4. Installing a new cylinder head gasket and dowels, and torquing the bolts in the correct sequence to specifications.
This document provides instructions for installing the cylinder head on a 4-cylinder engine. It includes:
1. Thoroughly cleaning the cylinder head and block mating surfaces.
2. Inspecting the cylinder head for distortion and replacing if needed.
3. Installing guide bolts into the cylinder block and using a degree wheel to ensure the cylinder head is parallel to the block.
4. Installing a new cylinder head gasket and dowels, and lubricating the gasket.
5. Gradually tightening the cylinder head bolts in the specified sequence and torque.
This document provides instructions for installing the rocker shaft and pushrods on a C2.2 engine. It describes 10 steps: cleaning parts, installing a new seal on the rocker shaft, applying oil to the pushrods, installing the pushrods and valve caps, installing the rocker shaft assembly, installing nuts and bolts and tightening them to specified torques, adjusting the valve lash, and installing additional components like the valve mechanism cover. The summary concludes by noting the document provides removal and installation instructions for other engine components.
This document provides instructions for installing the cylinder head on a 4-cylinder engine:
1. Thoroughly clean the cylinder head and cylinder block mating surfaces.
2. Inspect the cylinder head for distortion and replace if out of specification.
3. Install guide bolts through the cylinder block and install the new cylinder head gasket, ensuring dowel pins are correctly positioned.
1) The document provides instructions for removing and installing a lifter group on a C2.2 engine. It lists the required tool and removal steps, which include using a telescopic magnet to remove the lifters from the valve mechanism housing.
2) Installation instructions include cleaning components, lubricating the lifters, and inserting the lifters into the valve mechanism housing using the telescopic magnet. Proper lifter orientation is noted.
3) Completing the job involves installing the valve mechanism cover after checking lifter rotation.
This document provides instructions for installing the cylinder head on a 4-cylinder engine. It includes:
1. Thoroughly cleaning the cylinder head and block mating surfaces.
2. Inspecting the cylinder head for distortion and replacing if needed.
3. Installing guide bolts into the cylinder block and using a degree wheel to ensure the cylinder head is parallel to the block.
4. Installing a new cylinder head gasket and dowels, and torquing the bolts in the correct sequence to specifications.
1) The document provides instructions for removing and installing a lifter group on a C2.2 engine. It lists the required tool and removal steps, which include using a telescopic magnet to remove the lifters from the valve mechanism cover.
2) Installation instructions include cleaning components, lubricating the lifters, and inserting the lifters into the valve mechanism cover. Proper lifter orientation is noted.
3) Completion steps include installing the valve mechanism cover and related components.
Massey Ferguson MF 384 S TRACTOR (- 300993) Parts Catalogue Manual Instant Do...gua6982552kun
This document contains parts listings and technical specifications for the engine of a Massey Ferguson 384 S tractor. It includes 6 pages detailing over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, cylinder head, rocker shaft, and air induction/exhaust systems. Each part is listed with its part number, quantity used, description, and any replacement or comment information.
Massey Ferguson MF 384 F TRACTOR, - 0894 Parts Catalogue Manual Instant Downl...gua6982552kun
The document is a parts catalog for a Massey Ferguson MF 384 F tractor engine. It lists over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft and other components. Each part is given a reference number, part number, quantity and description, along with any replacement or additional part information.
Caterpillar Cat TH460B Telehandler (Prefix SLF) Service Repair Manual Instant...gua6982552kun
This document provides instructions for removing and installing various engine components on a Caterpillar 3054E engine, including the cylinder head, rocker shaft, lifters, and camshaft. The procedures describe cleaning parts, lubricating bolts, and torquing fasteners to the specified values. Special tools may be required and safety precautions are noted regarding containing fluids.
Caterpillar Cat TH350B Telehandler (Prefix SLD) Service Repair Manual Instant...gua6982552kun
This document provides instructions for disassembling and assembling parts of a TELEHANDLER Model TH350B powered by a 3054E engine. The summary includes:
1) Instructions are provided to remove and install the front gear group, housing, valve mechanism cover, rocker shaft assembly, and pushrods of the 3054E engine.
2) Detailed steps and illustrations guide the disassembly and reassembly of each component, including any required tools.
3) Proper cleaning and installation of seals and gaskets is emphasized to prevent contamination.
Caterpillar Cat TH340B Telehandler (Prefix SLC) Service Repair Manual Instant...gua6982552kun
This document provides instructions for removing and installing various components of a TH340B Telehandler including the flywheel housing, crankshaft pulley, crankshaft front seal, and front cover. The flywheel housing removal procedure involves using lifting equipment to support the housing while removing setscrews. The crankshaft pulley installation ensures proper lubrication and torque of setscrews. The crankshaft front seal removal uses a puller, while installation uses a special tool and nut to push the seal into place. Front cover removal and installation requires removing/installing setscrews and ensuring a clean gasket surface.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054B engine, including:
- Removing and installing the rocker arm and shaft, which involves installing new pushrods and oil seals and adjusting valve lash.
- Removing the cylinder head, which requires removing fuel injectors, exhaust manifolds, temperature regulators, rocker arms, and pushrods before loosening bolts and lifting the head off.
- Installing the cylinder head, which involves cleaning surfaces, installing a new gasket, torquing bolts in a specific sequence, and adjusting valve lash.
- Removing and installing the valve lifters using a magnet tool to pick them up
This document provides instructions for removing and installing the camshaft gear on a Caterpillar 3054B engine. The removal process involves aligning timing marks, removing a bolt and washer, and using a puller tool. The installation involves positioning the camshaft gear properly, installing the washer and bolt, and ensuring timing marks are aligned. Tools and torque specifications are provided.
This document provides assembly instructions for various components of a TH103 Telehandler 3PN transmission, including the forward high clutch drum assembly, forward high and reverse idler shaft assembly, output shaft and third clutch assembly, reversing clutch assembly, and second clutch assembly. The instructions include cleaning and inspecting parts, installing bearings and seals, assembling clutch components like springs, discs, and plates, and securing parts with retaining rings. Tools needed include retaining ring pliers, a compressor, and driver. Temperature and positioning details are provided for proper assembly.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a particular sequence, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3054 engine. The key steps are:
1. Drain coolant and remove components attached to the cylinder head like the air inlet manifold, exhaust manifold, fuel injection nozzles, and rocker arm assembly.
2. Gradually loosen the 22 cylinder head bolts in reverse tightening order.
3. Attach a lifting device and carefully remove the cylinder head, weighing 41 kg/90 lb. Remove the cylinder head gasket and note dowel pin locations.
4. Check for cylinder head distortion by aligning a straight edge with an installed bolt.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The procedures describe removing parts, cleaning them, installing new seals or lubricating components, and tightening fasteners to the specified torques. Safety notices are included to warn technicians about containing fluids and preventing contaminants.
This document provides instructions for removing and installing various engine components on a Caterpillar D6R track-type tractor, including:
- Removing the valve mechanism cover and gasket
- Removing the valve mechanism cover base and seal
- Removing the cylinder head by draining coolant, disconnecting harnesses and tubes, removing bolts, and lifting it off using a link bracket tool.
This document provides instructions for disassembling and assembling the torque divider of a D6G2 track-type tractor. It describes removing over 30 individual components of the torque divider including gears, seals, bearings, and housing pieces. Detailed illustrations and notes are provided to caution safe operation and containment of fluids. Proper cleaning and inspection of all parts is emphasized before reassembling the torque divider using the provided tools.
The document provides instructions for disassembling and assembling the piston pump steering system on a D5R2 track-type tractor. It details 39 steps to disassemble components such as the piston pump, valves, housing, pistons, and seals. It then lists 36 steps for reassembling these components in reverse order. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
This document provides instructions for removing and installing various components of a 3126B engine for a Caterpillar D5N track-type tractor, including the camshaft, camshaft gear, camshaft bearings, engine oil pan, and piston cooling jets. The procedures describe draining fluids, using required tools, cleaning and applying sealant to mating surfaces, and torquing bolts to specified values. Safety notices are provided to contain fluids and prevent contamination.
More Related Content
Similar to Caterpillar Cat CB564D Vibratory Compactor (Prefix D4M) Service Repair Manual Instant Download (D4M00001 and up).pdf
This document provides instructions for installing the cylinder head on a 4-cylinder engine. It includes:
1. Thoroughly cleaning the cylinder head and block mating surfaces.
2. Inspecting the cylinder head for distortion and replacing if needed.
3. Installing guide bolts into the cylinder block and using a degree wheel to ensure the cylinder head is parallel to the block.
4. Installing a new cylinder head gasket and dowels, and torquing the bolts in the correct sequence to specifications.
This document provides instructions for installing the cylinder head on a 4-cylinder engine. It includes:
1. Thoroughly cleaning the cylinder head and block mating surfaces.
2. Inspecting the cylinder head for distortion and replacing if needed.
3. Installing guide bolts into the cylinder block and using a degree wheel to ensure the cylinder head is parallel to the block.
4. Installing a new cylinder head gasket and dowels, and lubricating the gasket.
5. Gradually tightening the cylinder head bolts in the specified sequence and torque.
This document provides instructions for installing the rocker shaft and pushrods on a C2.2 engine. It describes 10 steps: cleaning parts, installing a new seal on the rocker shaft, applying oil to the pushrods, installing the pushrods and valve caps, installing the rocker shaft assembly, installing nuts and bolts and tightening them to specified torques, adjusting the valve lash, and installing additional components like the valve mechanism cover. The summary concludes by noting the document provides removal and installation instructions for other engine components.
This document provides instructions for installing the cylinder head on a 4-cylinder engine:
1. Thoroughly clean the cylinder head and cylinder block mating surfaces.
2. Inspect the cylinder head for distortion and replace if out of specification.
3. Install guide bolts through the cylinder block and install the new cylinder head gasket, ensuring dowel pins are correctly positioned.
1) The document provides instructions for removing and installing a lifter group on a C2.2 engine. It lists the required tool and removal steps, which include using a telescopic magnet to remove the lifters from the valve mechanism housing.
2) Installation instructions include cleaning components, lubricating the lifters, and inserting the lifters into the valve mechanism housing using the telescopic magnet. Proper lifter orientation is noted.
3) Completing the job involves installing the valve mechanism cover after checking lifter rotation.
This document provides instructions for installing the cylinder head on a 4-cylinder engine. It includes:
1. Thoroughly cleaning the cylinder head and block mating surfaces.
2. Inspecting the cylinder head for distortion and replacing if needed.
3. Installing guide bolts into the cylinder block and using a degree wheel to ensure the cylinder head is parallel to the block.
4. Installing a new cylinder head gasket and dowels, and torquing the bolts in the correct sequence to specifications.
1) The document provides instructions for removing and installing a lifter group on a C2.2 engine. It lists the required tool and removal steps, which include using a telescopic magnet to remove the lifters from the valve mechanism cover.
2) Installation instructions include cleaning components, lubricating the lifters, and inserting the lifters into the valve mechanism cover. Proper lifter orientation is noted.
3) Completion steps include installing the valve mechanism cover and related components.
Similar to Caterpillar Cat CB564D Vibratory Compactor (Prefix D4M) Service Repair Manual Instant Download (D4M00001 and up).pdf (7)
Massey Ferguson MF 384 S TRACTOR (- 300993) Parts Catalogue Manual Instant Do...gua6982552kun
This document contains parts listings and technical specifications for the engine of a Massey Ferguson 384 S tractor. It includes 6 pages detailing over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, cylinder head, rocker shaft, and air induction/exhaust systems. Each part is listed with its part number, quantity used, description, and any replacement or comment information.
Massey Ferguson MF 384 F TRACTOR, - 0894 Parts Catalogue Manual Instant Downl...gua6982552kun
The document is a parts catalog for a Massey Ferguson MF 384 F tractor engine. It lists over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft and other components. Each part is given a reference number, part number, quantity and description, along with any replacement or additional part information.
Caterpillar Cat TH460B Telehandler (Prefix SLF) Service Repair Manual Instant...gua6982552kun
This document provides instructions for removing and installing various engine components on a Caterpillar 3054E engine, including the cylinder head, rocker shaft, lifters, and camshaft. The procedures describe cleaning parts, lubricating bolts, and torquing fasteners to the specified values. Special tools may be required and safety precautions are noted regarding containing fluids.
Caterpillar Cat TH350B Telehandler (Prefix SLD) Service Repair Manual Instant...gua6982552kun
This document provides instructions for disassembling and assembling parts of a TELEHANDLER Model TH350B powered by a 3054E engine. The summary includes:
1) Instructions are provided to remove and install the front gear group, housing, valve mechanism cover, rocker shaft assembly, and pushrods of the 3054E engine.
2) Detailed steps and illustrations guide the disassembly and reassembly of each component, including any required tools.
3) Proper cleaning and installation of seals and gaskets is emphasized to prevent contamination.
Caterpillar Cat TH340B Telehandler (Prefix SLC) Service Repair Manual Instant...gua6982552kun
This document provides instructions for removing and installing various components of a TH340B Telehandler including the flywheel housing, crankshaft pulley, crankshaft front seal, and front cover. The flywheel housing removal procedure involves using lifting equipment to support the housing while removing setscrews. The crankshaft pulley installation ensures proper lubrication and torque of setscrews. The crankshaft front seal removal uses a puller, while installation uses a special tool and nut to push the seal into place. Front cover removal and installation requires removing/installing setscrews and ensuring a clean gasket surface.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054B engine, including:
- Removing and installing the rocker arm and shaft, which involves installing new pushrods and oil seals and adjusting valve lash.
- Removing the cylinder head, which requires removing fuel injectors, exhaust manifolds, temperature regulators, rocker arms, and pushrods before loosening bolts and lifting the head off.
- Installing the cylinder head, which involves cleaning surfaces, installing a new gasket, torquing bolts in a specific sequence, and adjusting valve lash.
- Removing and installing the valve lifters using a magnet tool to pick them up
This document provides instructions for removing and installing the camshaft gear on a Caterpillar 3054B engine. The removal process involves aligning timing marks, removing a bolt and washer, and using a puller tool. The installation involves positioning the camshaft gear properly, installing the washer and bolt, and ensuring timing marks are aligned. Tools and torque specifications are provided.
This document provides assembly instructions for various components of a TH103 Telehandler 3PN transmission, including the forward high clutch drum assembly, forward high and reverse idler shaft assembly, output shaft and third clutch assembly, reversing clutch assembly, and second clutch assembly. The instructions include cleaning and inspecting parts, installing bearings and seals, assembling clutch components like springs, discs, and plates, and securing parts with retaining rings. Tools needed include retaining ring pliers, a compressor, and driver. Temperature and positioning details are provided for proper assembly.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a particular sequence, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3054 engine. The key steps are:
1. Drain coolant and remove components attached to the cylinder head like the air inlet manifold, exhaust manifold, fuel injection nozzles, and rocker arm assembly.
2. Gradually loosen the 22 cylinder head bolts in reverse tightening order.
3. Attach a lifting device and carefully remove the cylinder head, weighing 41 kg/90 lb. Remove the cylinder head gasket and note dowel pin locations.
4. Check for cylinder head distortion by aligning a straight edge with an installed bolt.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The procedures describe removing parts, cleaning them, installing new seals or lubricating components, and tightening fasteners to the specified torques. Safety notices are included to warn technicians about containing fluids and preventing contaminants.
This document provides instructions for removing and installing various engine components on a Caterpillar D6R track-type tractor, including:
- Removing the valve mechanism cover and gasket
- Removing the valve mechanism cover base and seal
- Removing the cylinder head by draining coolant, disconnecting harnesses and tubes, removing bolts, and lifting it off using a link bracket tool.
This document provides instructions for disassembling and assembling the torque divider of a D6G2 track-type tractor. It describes removing over 30 individual components of the torque divider including gears, seals, bearings, and housing pieces. Detailed illustrations and notes are provided to caution safe operation and containment of fluids. Proper cleaning and inspection of all parts is emphasized before reassembling the torque divider using the provided tools.
The document provides instructions for disassembling and assembling the piston pump steering system on a D5R2 track-type tractor. It details 39 steps to disassemble components such as the piston pump, valves, housing, pistons, and seals. It then lists 36 steps for reassembling these components in reverse order. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
This document provides instructions for removing and installing various components of a 3126B engine for a Caterpillar D5N track-type tractor, including the camshaft, camshaft gear, camshaft bearings, engine oil pan, and piston cooling jets. The procedures describe draining fluids, using required tools, cleaning and applying sealant to mating surfaces, and torquing bolts to specified values. Safety notices are provided to contain fluids and prevent contamination.
This document provides assembly instructions for the piston pump on the left side of a D5K XL track-type tractor. It includes 40 steps to assemble various components like springs, seals, valves, plates, and housing pieces. Special tools are required and safety precautions mentioned, like following procedures carefully when assembling spring-loaded parts to avoid injury. Measurements must be taken to determine the correct shim thickness for the rotating group.
This document provides instructions for installing a cylinder head on a D4K2 XL track-type tractor. It describes cleaning and inspecting the cylinder head and cylinder block faces and installing dowels. It outlines torquing the bolts that secure the cylinder head in the correct sequence. Proper lubrication and alignment of the cylinder head gasket is emphasized to avoid leaks or damage.
This document provides instructions for removing and installing the valve mechanism cover on a Caterpillar D4K2 XL track-type tractor powered by a C4.4 engine. The procedure involves removing bolts and brackets to access the cover, then removing and installing a new gasket before reinstalling the cover and related components. Separate sections provide details on disassembling and assembling the rocker shaft and related parts.
This document provides instructions for removing and installing the front gear group of a C15 Industrial Engine N5F. Key steps include removing the front housing, camshaft gear, and various gears and plates. Installation involves cleaning parts, applying thread lock to bolts, and adjusting backlash between gears. Tightening torques and sequences are specified.
This document provides instructions for removing and installing an engine oil filter base on a C13 Industrial Engine N3F. The removal procedure involves draining the engine oil, then removing hoses, fittings, bolts and the oil filter base. Several internal components like springs and plungers must also be removed from the base. For installation, the base and components are reinstalled in reverse order, applying lubricant to seals and filters. Torque specifications are provided for several installation steps.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Caterpillar Cat CB564D Vibratory Compactor (Prefix D4M) Service Repair Manual Instant Download (D4M00001 and up).pdf
1. Product: VIBRATORY COMPACTOR
Model: CB-564D VIBRATORY COMPACTOR D4M
Configuration: CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02294250
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. The weight of the flywheel housing (3) is approximately 39 kg (85 lb). Use suitable lifting
equipment to support the flywheel housing (3) while the setscrews (1) are being removed
and while the flywheel housing is being removed.
Illustration 1 g00977367
2. Remove the setscrews (1) from the top of the flywheel housing (3).
3. Attach the Tooling (A) and a suitable lifting device to the flywheel housing (3).
4. Remove the setscrews (2) that attach the flywheel housing (3) to the cylinder block.
5. Remove the flywheel housing (3). If necessary, tap the flywheel housing with a soft faced
hammer in order to separate the flywheel housing from the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
2/4
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing (3).
Illustration 2 g00977388
2. If a felt seal (5) is installed, replace the felt seal. Inspect the dowels (4) in the cylinder block
that align the flywheel housing (3). Replace the dowels, if necessary.
3. The weight of the flywheel housing (3) is approximately 39 kg (85 lb). Use the Tooling (A)
and a suitable lifting device to position the flywheel housing (3) on the dowels (4) that are
on the cylinder block.
4. Install the setscrews (1) that attach the flywheel housing (3) to the cylinder block.
5. Install the setscrews (2) that attach the flywheel housing (3) to the cylinder block.
Tighten the setscrews (1) and the setscrews (2) to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
6. Remove Tooling (A) and the lifting device from the flywheel housing.
3/4
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 7. Check the alignment of the flywheel housing with the cylinder block. Refer to Testing and
Adjusting, "Flywheel Housing - Inspect".
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
4/4
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Product: VIBRATORY COMPACTOR
Model: CB-564D VIBRATORY COMPACTOR D4M
Configuration: CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02294252
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00952102
1. Remove the setscrews (1). Remove the thrust block (2).
2. Remove the pulley (3) from the crankshaft (4).
Installation Procedure
Illustration 2 g00952102
1. Clean the pulley (3) and clean the thrust block (2). Inspect the pulley (3) and the thrust
block (2) for wear and for damage. If necessary, replace any damaged component. Inspect
the area on the pulley (3) that is normally in contact with the crankshaft front seal. If there is
excessive wear then a wear sleeve can be installed. Refer to this Disassembly and Assembly
2/3
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Manual, "Crankshaft Wear Sleeve (Front) - Remove and Crankshaft Wear Sleeve (Rear) -
Install" for further details.
2. Position the pulley (3) onto the crankshaft (4).
3. Lubricate the threads and the shoulder of the setscrews (1). Position the thrust block and
install the setscrews (1). Tighten the setscrews evenly to a final torque of 115 N·m
(85 lb ft).
End By:
a. Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
3/3
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Product: VIBRATORY COMPACTOR
Model: CB-564D VIBRATORY COMPACTOR D4M
Configuration: CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02294258
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Note: Do not remove the crankshaft front seal at this time if the housing (front) will also be
removed. It is easier to remove the crankshaft front seal when the housing (front) has been
removed from the engine. Refer to this Disassembly and Assembly Manual, "Housing (Front) -
Remove".
Illustration 1 g01020672
1. Use a suitable puller (1) with three legs and install the legs under the crankshaft front seal
(2). Lock the legs into position.
2. Install a suitable adapter (3) between the crankshaft (4) and the puller (1).
NOTICE
Ensure that the main lip is used in order to remove the crankshaft
front seal. Do not damage the edge of the housing for the crankshaft
front seal.
3. Use the puller (1) in order to remove the crankshaft front seal (2). Discard the crankshaft
front seal (2).
NOTICE
Ensure that the main lip is used in order to remove the crankshaft
front seal. Do not damage the edge of the housing for the crankshaft
front seal.
2/3
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Product: VIBRATORY COMPACTOR
Model: CB-564D VIBRATORY COMPACTOR D4M
Configuration: CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02294259
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: This procedure assumes that the housing (front) is still on the engine. Do not follow this
procedure if the housing (front) has been removed from the engine. Refer to this Disassembly and
Assembly Manual, "Housing (Front) - Install" if the housing (front) has been removed from the
engine.
1. Clean the oil seal housing (8) and inspect the oil seal housing for damage. If necessary,
replace the housing (front). Refer to this Disassembly and Assembly Manual, "Housing
(Front) - Remove and Housing (Front) - Install".
2. Check the face on the pulley that contacts the crankshaft front seal for wear. If necessary,
repair the crankshaft pulley. Refer to this Disassembly and Assembly Manual, "Crankshaft
Wear Sleeve (Front) - Remove and Crankshaft Wear Sleeve (Front) - Install" for further
details.
1/3
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Note: A sleeve (5) is attached to the new crankshaft front seal (6). Do not remove the sleeve
(5) at this time. Discard the new crankshaft front seal (6) if the sleeve (5) is not installed on
the new crankshaft front seal.
Illustration 1 g01148784
The Tooling (A) includes items 1, 2, 3, 4, 7 and 9.
3. Install the fastener plate (7) onto the front of the crankshaft. Install the nut (1) and the
pressure plate (2) onto the threaded bar (3).
Note: Do not lubricate the crankshaft front seal (6). Do not lubricate the oil seal housing (8).
NOTICE
Ensure that the lip of the crankshaft front seal that is spring loaded is
facing toward the inside of the front housing and that it is square with
the bore of the housing for the crankshaft front seal.
4. Align the assembly of the sleeve (5) and the crankshaft front seal (6) to the front of the oil
seal housing (8).
5. Install the adapter (4) onto the sleeve (5).
6. Install the pressure plate (2) onto the adapter (4) and tighten the threaded bar (3) onto the
fastener plate (7). Check the alignment of the assembly and the crankshaft front seal (6) to
the oil seal housing (8).
7. Insert a suitable rod through the hole (9) in the threaded bar (3) in order to prevent the
threaded rod from turning as the nut (1) is tightened. Tighten the nut (1) in order to push the
2/3
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. crankshaft front seal (6) into the oil seal housing (8). Continue to tighten the nut (1) until
contact is made with the bottom face of the oil seal housing (8).
8. Turn the sleeve (5) counterclockwise and pull the sleeve at the same time in order to remove
the sleeve from the oil seal housing (8). Remove the adapter (7).
9. Immediately install the crankshaft pulley. Refer to this Disassembly and Assembly Manual,
"Crankshaft Pulley - Remove and Install".
3/3
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Product: VIBRATORY COMPACTOR
Model: CB-564D VIBRATORY COMPACTOR D4M
Configuration: CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02294796
Front Cover - Remove and Install
SMCS - 1166-010
Removal Procedure
Start By:
a. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove and
Install".
Note: It is not necessary to remove the fan, the crankshaft pulley or the alternator in order to
remove the front cover. The fan, the crankshaft pulley and the alternator have been removed for
illustration purposes.
Illustration 1 g00955548
1/3
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 1. Remove the setscrews (3) and the setscrews (4). Remove the setscrew (5) from the front
cover (1).
2. Remove the front cover from the front housing.
3. Remove the gasket (2) from the front cover and the front housing. Discard the gasket.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(M8 x 1.25 x 70mm)
2
1. Clean all surfaces of the front housing and clean the front cover thoroughly.
Note: Do not use sealant on the gasket for the front cover.
Illustration 2 g00955554
2. Position the gasket (2) on the front cover (1).
Note: The gasket is located by three locating dowels at Location (X) on the front cover.
3. Install the Tooling (A) in the front housing at Location (Z).
4. Position the front cover (1) and the gasket (2) on the front housing. Install the setscrews (3)
in Location (Y). Install the setscrews (4) and the setscrew (5). Tighten the setscrews to a
torque of 22 N·m (16 lb ft).
2/3
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. End By:
a. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove and
Install".
3/3
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Product: VIBRATORY COMPACTOR
Model: CB-564D VIBRATORY COMPACTOR D4M
Configuration: CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i01875845
Idler Gear - Remove and Install - Delphi DP210 Fuel
Injection Pump
SMCS - 1206
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A 9U-6198 Crankshaft Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 230-6283 Timing Pin (Crankshaft) 1
D 1P-2320 Combination Puller 1
E 1P-0510 Driver Group 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
b. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/8
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Use Tooling (A) to ensure that the No. 1 cylinder is at the top center compression stroke.
Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Note: Install Tooling (B) through the camshaft gear. Install Tooling (C) into the crankshaft
web.
NOTICE
The valve timing and the fuel injection pump timing will be lost if the
crankshaft is rotated when the idler gear is removed.
2/8
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00992803
2. Loosen bolt (1). Move spacer (2) in order to allow bolt (1) to tighten against the shaft of the
fuel injection pump. Rotate and hold the fuel injection pump gear in a counterclockwise
direction in order to remove the backlash. Tighten bolt (1) to a torque of 17 N·m (13 lb ft).
Note: Bolt (1) must be tightened in order to prevent the shaft of the fuel injection pump
from rotating.
Illustration 2 g00992812
3. Remove nut (3) and the washer from the shaft of the fuel injection pump.
4. Install Tooling (D) and remove fuel injection pump gear (4).
Note: Do Not pry the fuel injection pump gear from the shaft of the fuel injection pump.
5. Remove bolts (7) and retaining plate (6).
3/8
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 3 g00992822
6. Remove idler gear (5) and idler gear hub (9).
7. Use Tooling (E) and remove bushings (8) from each side of the idler gear.
Installation Procedure
Table 2
A 9U-6198 Crankshaft Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 230-6283 Timing Pin (Crankshaft) 1
E 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (A) to ensure that the No. 1 cylinder is at the top center compression stroke.
Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Note: Install Tooling (B) through the camshaft gear. Install Tooling (C) into the crankshaft
web.
4/8
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. NOTICE
The valve timing and the fuel injection pump timing will be lost if the
crankshaft is rotated when the idler gear is removed.
Illustration 4 g00943872
2. Position idler gear hub (9) and install bolts (7) in order to locate the idler gear hub. Tighten
the bolts in order to seat the idler gear hub.
Note: The Lubrication Hole (X) of the idler gear hub must be positioned at the top of the
idler gear hub.
3. Use a suitable press and Tooling (E) to install bushings (8) on each side of idler gear (5).
4. Remove bolts (7) from the idler gear hub. Install idler gear (5) on idler gear hub (9).
Note: When you install the idler gear, ensure that the marked teeth are facing toward the
front.
5. Install retainer plate (6) and bolts (7). Tighten the bolts to a torque of 44 N·m (32 lb ft).
5/8
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 5 g00944081
6. Check the end play for the idler gear. The end play for the idler gear is 0.10 to 0.20 mm
(0.004 to 0.008 inch).
Illustration 6 g00944084
7. Check the backlash between the idler gear and the camshaft gear. The backlash for the gears
is 0.052 to 0.107 mm (0.0020 to 0.0042 inch).
8. Check the backlash between the idler gear and the crankshaft gear. The backlash for the
gears is 0.064 to 0.124 mm (0.0025 to 0.0049 inch).
6/8
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 7 g00992853
Note: Ensure that the mating surfaces of the fuel injection pump gear and the shaft of the
fuel injection pump are clean. Lubricate the threads of the shaft for the fuel injection pump.
The nut must turn freely until contact is made with the fuel injection pump gear.
9. Position fuel injection pump gear (4) on the shaft of the fuel injection pump. Rotate the fuel
injection pump gear in a counterclockwise direction in order to remove the backlash. Install
the washer and nut (3). Tighten the nut to a torque of 24 N·m (17 lb ft).
Illustration 8 g00992803
10. Loosen bolt (1). Move spacer (2) in order to prevent bolt (1) from tightening against the
shaft of the fuel injection pump. Tighten bolt (1) to a torque of 12 N·m (106 lb in).
Note: Spacer (2) must be correctly positioned and bolt (1) must be tightened in order to
prevent the bolt from contacting the shaft of the fuel injection pump.
7/8
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Suggest:
For more complete manuals. Please go to
the home page.
https://www.ebooklibonline.com
If the above button click is invalid. Please
download this document first, and then
click the above link to download the
complete manual.
Thank you so much for reading
24. Illustration 9 g00992883
11. Tighten nut (3) to a torque of 88 N·m (65 lb ft).
12. Remove Tooling (B) and Tooling (C).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
b. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
8/8
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Product: VIBRATORY COMPACTOR
Model: CB-564D VIBRATORY COMPACTOR D4M
Configuration: CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i05324845
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove".
b. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
c. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
d. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
e. Remove the idler gear. Refer to Disassembly and Assembly, "Idler Gear - Remove and
Install".
f. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
g. Remove the air compressor, if equipped. Refer to Disassembly and Assembly, "Air
Compressor - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
CB564D Vibratory Compactor D4M00001-UP (MACHINE) POWERED BY 3054C E...
2021/5/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...