This document provides instructions for removing and installing the front gear group of a C15 Industrial Engine N5F. Key steps include removing the front housing, camshaft gear, and various gears and plates. Installation involves cleaning parts, applying thread lock to bolts, and adjusting backlash between gears. Tightening torques and sequences are specified.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Bài tập - Tiếng anh 11 Global Success UNIT 1 - Bản HS.doc
Caterpillar Cat C15 Industrial Engine (Prefix N5F) Service Repair Manual Instant Download (N5F00001 and up).pdf
1. Product: INDUSTRIAL ENGINE
Model: C15 INDUSTRIAL ENGINE N5F
Configuration: C15 Industrial Engine N5F00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -UENR0185-03 Publication Date -01/08/2015 Date Updated -27/08/2015
i05949761
Gear Group (Front) - Remove and Install
SMCS - 1206-010
S/N - N5F1-UP
S/N - N8F1-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B 8T-2998 Lubricant -
C 8T-9022 Silicone Gasket -
D 9S-3263 Thread Lock Compound -
Start By:
a. Remove the front housing.
b. Remove the air compressor, if necessary.
c. Remove the water pump, if necessary.
NOTICE
Keep all parts clean from contaminants.
1/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
2. Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
Note: Be sure to mark the orientation of each of the gears for installation purposes.
Illustration 1 g01008429
1. Remove bolts (2) and thrust plate (1).
2/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 2 g01008430
2. Remove sealing plate (3) and adapter (4).
Illustration 3 g01008431
3. Remove O-ring seal (5) and O-ring seal (6) from sealing plate (3).
3/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 4 g01101536
4. Remove bolts (8), plate (9), and adjustable idler gear assembly (7).
5. Use Tooling (A) and remove the sleeve bearing from adjustable idler gear assembly (7).
4/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 5 g01101045
6. Remove bolts (11), plate (12), and idler gear assembly (10).
7. Use Tooling (A) and remove the sleeve bearing from idler gear assembly (10).
5/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 6 g01101048
8. Remove bolts (14), plate (15), and cluster gear assembly (13).
9. Use Tooling (A) and remove the sleeve bearing from cluster gear assembly (13).
6/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 7 g01101050
Note: Stub shaft assembly (16) must be removed in order to remove plate (22). The
backlash for the camshaft gear and the adjustable idler gear assembly will need to be
readjusted at assembly.
10. Remove nuts (17) and remove stub shaft assembly (16).
Note: Stub shaft (18) must be removed in order to remove plate (22).
11. Remove nuts (19) and remove stub shaft (18).
12. Remove bolts (21) and remove stub shaft (20).
13. Remove bolts (23) that hold plate (22) to the cylinder block. Remove plate (22).
14. If studs (24) are loose or the threads are damaged, remove the studs from the front plate.
7/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 8 g01101052
15. Remove integral seal (25) from the cylinder block.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
8/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 1. Thoroughly clean the gasket material from the cylinder block and both sides of the plate.
Illustration 9 g01101567
2. If studs (24) are loose or the threads are damaged, install new studs (24) in the front plate.
Apply Tooling (D) to the serrations of studs (24). Install studs (24) in the front plate.
3. Install integral seal (25) on the dowel pins on the cylinder block.
Note: Apply Tooling (C) to the bottom of integral seal (25) in order to fill the space at the
cylinder block, the front housing, and the engine oil pan.
4. Install plate (22) on the dowel pins on the cylinder block. Install new locking bolts (23)
(Marked "X") in order to fasten the front plate to the cylinder block. Tighten locking bolts
(23) to a torque of 55 N·m (41 lb ft).
Note: Clean the old sealant from the bolts and apply Tooling (D) to the bolts.
5. Tighten locking bolts (23) again to a torque of 55 N·m (41 lb ft).
9/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 10 g01101565
6. Install stub shaft (18). Apply Tooling (D) to the studs and the bolt for stub shaft (18).
Tighten nuts (19) and the bolt to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
7. Install stub shaft assembly (16). Apply Tooling (D) to the studs and the bolt for stub shaft
assembly (16). Do not tighten nuts (17) and the bolt for stub shaft assembly (16) at this
time. Nuts (17) and the bolt for stub shaft assembly (16) will need to be tightened when the
backlash is adjusted.
8. Adjust the backlash between the camshaft gear and the adjustable idler gear assembly. The
backlash should be 0.356 ± 0.254 mm (0.014 ± 0.010 inch). Refer to Testing and Adjusting,
"Gear Group (Front) - Time" for the backlash adjustment procedure. Tighten nuts (17) and
the bolt to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
9. Install stub shaft (20). Apply Tooling (D) to bolts (21). Install bolts (21) and tighten in a
numeric sequence 1, 3, 4, 5, 2, 1, 2, 3, 4, 5, 1 to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
10/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 11 g01101161
10. Use Tooling (A) to install the sleeve bearing in cluster gear assembly (13).
11. Put cluster gear assembly (13) on the stub shaft. Ensure that Timing Marks (V) are aligned
on the cluster gear assembly and the crankshaft gear.
12. Position plate (15) with the oil groove toward the face of the gear. Apply Tooling (D) to
bolts (14). Install bolts (14). Tighten bolts (14) to a torque of 30 ± 7 N·m (22 ± 5 lb ft).
11/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 12 g01101045
13. Use Tooling (A) to install the sleeve in idler gear (10).
14. Put idler gear assembly (10) on the stub shaft. Install plate (12) with the oil groove toward
the gear face. Apply Tooling (D) to bolts (11). Install bolts (11). Tighten bolts (11) to a
torque of 30 ± 7 N·m (22 ± 5 lb ft).
12/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 13 g01008436
15. Use Tooling (A) to install the sleeve bearing in adjustable idler gear (7).
Note: Align the oil hole in the bearing with the oil hole in the adjustable idler gear.
16. Put adjustable idler gear assembly (7) on the stub shaft assembly. Position plate (9) with the
oil groove toward the face of the gear. Apply Tooling (D) to bolts (8). Install bolts (8).
Tighten bolts (8) to a torque of 30 ± 7 N·m (22 ± 5 lb ft).
Note: Check the backlash for the camshaft gear and the adjustable idler gear assembly. The
camshaft gear must be installed and the adjustable idler gear assembly must be removed in
order to perform the backlash adjustment procedure. Refer to Testing and Adjusting, "Gear
Group (Front) - Time".
13/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 14 g01008431
17. Install O-ring seal (5) and O-ring seal (6) in sealing plate (3). Lubricate O-ring seal (6) with
a 50/50 mixture of Tooling (B) and clean engine oil.
Illustration 15 g01008430
14/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 16 g01010256
18. Install adapter (4). Ensure that the dowel in the adapter engages the hole in the camshaft.
19. Install sealing plate (3) and thrust plate (1). Ensure that the dowel in the adapter engages the
hole in the thrust plate. Apply Tooling (D) to bolts (2). Install bolts (2). Evenly tighten bolts
(2) in order to ensure that sealing plate (3) and O-ring seal (5) are seated against the cylinder
head.
20. Adjust the backlash for the camshaft gear and the adjustable idler gear, if necessary. Refer
to Testing and Adjusting, "Gear Group (Front) - Time".
Note: The camshaft gear must be installed and the adjustable idler gear must be removed in
order to perform the backlash adjustment procedure.
End By:
a. Install the water pump.
b. Install the air compressor, if necessary.
c. Install the front housing.
15/15(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Product: INDUSTRIAL ENGINE
Model: C15 INDUSTRIAL ENGINE N5F
Configuration: C15 Industrial Engine N5F00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -UENR0185-03 Publication Date -01/08/2015 Date Updated -27/08/2015
i05356423
Housing (Front) - Remove and Install
SMCS - 1151-010
S/N - N5F1-UP
S/N - N8F1-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 154-9731 Thread Lock Compound -
B 8T-9022 Silicone Gasket -
Start By:
a. Remove the camshaft position sensor.
b. Remove the crankshaft position sensor.
c. Remove the engine support.
d. Remove the camshaft gear.
e. Remove the crankshaft front seal.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/6(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
Illustration 1 g01078059
2/6(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. 1. Remove the bolts and clips (1).
2. Remove bracket (2) from plate (4) and the cylinder head.
3. Remove bolts (3).
Illustration 2 g01078084
4. Remove cable strap (5) from the cylinder head and front housing (10).
5. Remove bolt (7) and nut (6) from the front housing.
6. Remove bolts (8) and nuts (9) from the front housing.
7. Remove bolts (11) from the front housing.
Illustration 3 g01078119
3/6(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. 8. Loosen bolts (15) from the engine oil pan.
Note: It is not necessary to remove the engine oil pan from the engine.
9. Remove front housing (10).
10. If necessary, remove studs (14) and the O-ring seals from the front housing.
11. Remove gasket (12) from plate (13) and the front housing.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not turn the crankshaft or the camshaft while the camshaft gear is
removed. If the front gear group is not correctly timed during
installation, interference can occur between the pistons and the valves,
resulting in damage to the engine.
Illustration 4 g01078406
4/6(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 1. If studs (14) are loose or the threads are damaged, install new studs in front housing (10).
Apply Tooling (A) to the threads of studs (14). Install the O-ring seals on the studs and
install the studs in the front housing.
2. Thoroughly clean the mating surfaces of plate (13) and front housing (10).
3. Install gasket (12) on plate (13).
Note: Trim the gasket even with the bottom of the front housing after assembly.
4. Apply Tooling (B) to the bottom of gasket (12) in order to fill the space at the front housing
and the engine oil pan.
5. Install front housing (10) on the dowel pins on the cylinder block.
6. Install bolts (11) in front housing (10).
7. Tighten bolts (15).
Illustration 5 g01078272
8. Install bolt (7) and nuts (6).
9. Install bolts (8) and nuts (9).
10. Install cable strap (5) on the front housing and on the cylinder head.
5/6(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 6 g01078059
11. Install the bolts and clips (1).
12. Install bolts (3).
13. Install bracket (2) on plate (4) and the front housing.
End By:
a. Install the crankshaft front seal and the wear sleeve.
b. Install the camshaft gear.
c. Install the engine support.
d. Install the camshaft position sensor.
e. Install the crankshaft position sensor.
6/6(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Product: INDUSTRIAL ENGINE
Model: C15 INDUSTRIAL ENGINE N5F
Configuration: C15 Industrial Engine N5F00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -UENR0185-03 Publication Date -01/08/2015 Date Updated -27/08/2015
i04730375
Fumes Disposal Filter - Remove and Install
SMCS - 1317-010
S/N - N5F1-UP
S/N - N8F1-UP
Removal Procedure
Illustration 1 g02831020
1. Disconnect hoses (2), (4), (5).
2. Remove bolts (3) and remove fumes disposal filter assembly (1).
1/2(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 2 g02831066
3. Remove the cap from fumes disposal filter assembly (1). Remove element (6) and the O-
ring seal.
Installation Procedure
1. Install fumes disposal filter assembly (1) in the reverse order of removal.
2/2(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Suggest:
For more complete manuals. Please go to
the home page.
https://www.ebooklibonline.com
If the above button click is invalid. Please
download this document first, and then
click the above link to download the
complete manual.
Thank you so much for reading
25. Product: INDUSTRIAL ENGINE
Model: C15 INDUSTRIAL ENGINE N5F
Configuration: C15 Industrial Engine N5F00001-UP
Disassembly and Assembly
C15 and C18 Industrial Engines
Media Number -UENR0185-03 Publication Date -01/08/2015 Date Updated -27/08/2015
i05375406
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
S/N - N5F1-UP
S/N - N8F1-UP
Removal Procedure
Start By:
A. Remove the clean emissions module.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 1 g01078498
1. Remove bolts (1).
2. Remove valve mechanism cover (2) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2022/3/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...