This document provides instructions for disassembling and assembling parts of a TELEHANDLER Model TH350B powered by a 3054E engine. The summary includes:
1) Instructions are provided to remove and install the front gear group, housing, valve mechanism cover, rocker shaft assembly, and pushrods of the 3054E engine.
2) Detailed steps and illustrations guide the disassembly and reassembly of each component, including any required tools.
3) Proper cleaning and installation of seals and gaskets is emphasized to prevent contamination.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
1. Product: TELEHANDLER
Model: TH350B TELEHANDLER SLD
Configuration: TH350B Telehandler SLD00001-01640 (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02253357
Gear Group (Front) - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2264 Puller Group 1
B 173-9774 Wrench Bit 1
Start By:
A. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
2. Illustration 1 g00556563
Note: It may be necessary to pin the fuel pump in order to maintain the correct timing.
Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove"for the correct
procedure.
1. Align the timing marks on the crankshaft gear, the camshaft gear, and the idler gear, as
shown.
2. Remove bolts (1) from idler gear (2) .
3. Remove idler gear (2) and retainer plate (3) .
Illustration 2 g00556757
4. Remove bushing (4) from idler gear (2) , if necessary.
5. Remove the bushing with a suitable puller. If the bushing cannot be removed with a puller,
grind the face off of one bushing. The remainder of the bushing can then be removed with a
press.
2/3(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 3 g00556758
6. Remove idler gear hub (5) from the cylinder block.
7. Remove nut (6) and the spring washer from fuel injection pump gear (8) .
8. Remove bolts (7) from fuel injection pump gear (8) .
Note: Some fuel injection pump gears may have a tamper proof torx screw in place of one
of the four bolts. Use Tooling (B) to remove the tamper proof torx screw, if necessary.
9. Use Tooling (A) to remove fuel injection pump gear (8) .
3/3(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Product: TELEHANDLER
Model: TH350B TELEHANDLER SLD
Configuration: TH350B Telehandler SLD00001-01640 (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01744102
Gear Group (Front) - Install
SMCS - 1206-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00556758
1. Install fuel injection pump gear (8) on the engine.
2. Install bolts (7) on fuel injection pump gear (8).
1/3(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 3. Install nut (6) and the spring washer on fuel injection pump gear (8). Tighten the nut to a
torque of 80 N·m (59 lb ft).
4. Install idler gear hub (5) on the engine.
Illustration 2 g00556757
5. Use a suitable press to install new bushings (4) into idler gear (2).
6. Machine the bores for clearance on idler gear hub (5). The bore should have a clearance of
0.04 to 0.010 mm (0.0016 to 0.0039 inch) on idler gear hub (5). The bore can have a
diameter of 57.14 to 57.18 mm (2.250 to 2.251 inch).
7. Machine the front faces of the bushings for the end play of idler gear (2). The gear and the
bushings can have a thickness of 30.14 to 30.16 mm (1.186 to 1.187 inch).
Illustration 3 g00556563
8. Install idler gear (2) and retainer plate (3) on the engine.
Note: Ensure that the timing marks on the camshaft gear, the crankshaft gear, and the idler
gear are aligned.
9. Install bolts (1) on idler gear (2). Tighten the bolts to a torque of 44 N·m (32 lb ft).
10. Check the end play of idler gear (2). Idler gear (2) should have end play of 0.10 to 0.20 mm
(0.004 to 0.008 inch).
2/3(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. 11. Check the backlash between the camshaft gear and idler gear (2). The gears must have a
minimum backlash of 0.08 mm (0.003 inch).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
3/3(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Product: TELEHANDLER
Model: TH350B TELEHANDLER SLD
Configuration: TH350B Telehandler SLD00001-01640 (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01744128
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
b. Remove the front gear group. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove".
c. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00549819
1. Remove all bolts (1) that fasten the front housing (2) to the cylinder block.
Illustration 2 g00549821
2. Remove bolts (3) that hold the oil pan to the bottom of front housing (2).
3. Remove front housing (2) and the gasket.
2/2(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Product: TELEHANDLER
Model: TH350B TELEHANDLER SLD
Configuration: TH350B Telehandler SLD00001-01640 (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i06815567
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite Gasket Sealant No. 2 -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Replace the gasket.
2. Apply Tooling (A) to the bottom portion of the gasket.
1/3(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 1 g00549821
3. If necessary, install the studs (not shown) to the back of the front housing (2) that holds the
fuel injection pump in position. Tighten the studs to a torque of 11 N·m (97 lb in). Install
the gasket and front housing (2). Cut the gasket to the correct length, if necessary.
4. Install bolts (3) that hold the engine oil pan to the bottom of the front housing. Tighten the
bolts to a torque of 22 N·m (16 lb ft).
Illustration 2 g00549819
2/3(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 3 g03549798
5. Install all bolts (1) that fasten the front housing (2) to the cylinder block and to the oil pan.
Tighten bolts (1) to a torque of 22 N·m (16 lb ft) using the sequence in Illustration 3.
Note: Ensure that the bottom of the front housing is aligned with the bottom of the cylinder
block.
End By:
a. Install the camshaft gear.
b. Install the front gear group.
c. Install the engine oil pan.
3/3(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Product: TELEHANDLER
Model: TH350B TELEHANDLER SLD
Configuration: TH350B Telehandler SLD00001-01640 (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01054405
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: The engines are equipped with either an aluminum valve cover or with a composite valve
cover. The aluminum valve cover has a seal that fits between the valve cover and the inlet
1/5(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. manifold. The composite valve cover has a seal that is permanently fixed to the side of the valve
cover.
Illustration 1 g00547002
Typical example
Illustration 2 g00547003
Aluminum valve cover
2/5(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 3 g00547004
Composite valve cover
1. Loosen hose clamp (1) .
2. Disconnect breather hose (2) .
3. Remove three nuts (3), steel washers (6), and sealing washers (8) .
Note: When you remove nuts (3), ensure that the nuts on the rocker arm bracket are not
loosened.
Note: Current production engines have an additional shim washer (7) .
4. Remove valve cover (4), gasket (10), and seal (5) .
5. Remove seal (9) for the oil filler cap.
Installation Procedure
Note: The engines are equipped with either an aluminum valve cover or with a composite valve
cover. The aluminum valve cover has a seal that fits between the valve cover and the inlet
manifold. The composite valve cover has a seal that is permanently fixed to the side of the valve
cover.
3/5(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 4 g00547002
Typical example
Illustration 5 g00547003
Aluminum valve cover
4/5(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 6 g00547004
Composite valve cover
1. Inspect the condition of the gaskets and the seals. Replace the gaskets and the seals, if
necessary.
2. Install seal (9) for the oil filler cap, if necessary.
3. Apply 8T-9022 Silicone Gasket to gasket (10) .
Note: Ensure that the flat face of the gasket is toward the valve cover.
4. Install gasket (10), seal (5), and valve cover (4) .
5. Lubricate three nuts (3) with clean engine oil.
6. Install three nuts (3), steel washers (6), and sealing washers (8) .
Note: When you install three nuts (3) without shim washers (7), tighten the nuts to a torque
of 20 N·m (15 lb ft). Do not overtighten the nuts.
Note: When you install three nuts (3) with shim washers (7), tighten the nuts to a torque of
30 N·m (22 lb ft). Do not overtighten the nuts.
7. Connect breather hose (2) .
8. Tighten hose clamp (1) .
5/5(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Product: TELEHANDLER
Model: TH350B TELEHANDLER SLD
Configuration: TH350B Telehandler SLD00001-01640 (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01761173
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00635152
1/2(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Typical example
Note: It is not necessary to remove the oil supply tube in order to remove the rocker shaft
assembly and the pushrods.
1. Remove nuts (1) and bolt (2) from the rocker shaft assembly. Begin with the end brackets
and move toward the center.
2. Remove rocker shaft assembly (3).
3. Remove the oil seal from the oil supply passage in the cylinder head.
Illustration 2 g00635153
Typical example
4. Remove pushrods (4). Place an identification mark on the pushrods for installation.
2/2(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Product: TELEHANDLER
Model: TH350B TELEHANDLER SLD
Configuration: TH350B Telehandler SLD00001-01640 (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01667090
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
A. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
Illustration 1 g00550061
1/3(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 1. Use a screwdriver or a similar tool to remove retaining ring (1) from both ends of the rocker
shaft assembly.
Illustration 2 g00550062
(1) Retaining ring
(2) Washer on the end of the rocker shaft
(3) Rocker arm assembly
(4) Rocker shaft bracket
(5) Spring on the rocker shaft
(6) Washer
(7) Rocker shaft
(8) Bolt
(9) Oil supply connection
(10) Rocker arm bushing
2. Remove the rocker arms and the rocker shaft brackets from the rocker shaft assembly.
Note: Place an identification mark on each of the components for the proper order for
installation.
3. Check the clearance between rocker arm assembly (3) and rocker shaft (7). Replace rocker
arm bushing (10) if the clearance is larger than 0.13 mm (0.005 inch). Use Tool (A) and a
suitable press in order to remove rocker arm bushing (10) from rocker arm assembly (3), if
necessary.
4. Remove rocker shaft bracket (4) from rocker shaft (7) .
5. Remove springs (5), washer (6), bolt (8) and oil supply connection (9) from rocker shaft
(7) .
2/3(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Product: TELEHANDLER
Model: TH350B TELEHANDLER SLD
Configuration: TH350B Telehandler SLD00001-01640 (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01667093
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
1. Lubricate all of the components with clean engine oil.
Illustration 1 g00550062
(1) Retaining ring
(2) Washer on the end of the rocker shaft
(3) Rocker arm assembly
(4) Rocker shaft bracket
(5) Spring on the rocker shaft
(6) Washer
(7) Rocker shaft
1/2(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. (8) Bolt
(9) Oil supply connection
(10) Rocker arm bushing
2. Install oil supply connection (9) and bolt (8) on rocker shaft (7) .
Note: Ensure that the bolt and the connection are correctly positioned on the rocker shaft.
Note: Ensure that all of the oil holes in the rocker shaft and in the rocker arms are not
plugged before you begin the assembly procedure.
3. Install rocker arm bushing (10) in rocker arm assembly (3) with a suitable press. Ream the
bushing to a clearance of 0.06 ± 0.03 mm (0.0024 ± 0.0012 inch), if necessary.
4. Install each of the components in the correct order onto rocker shaft (7). See Illustration 1.
Illustration 2 g00550061
5. Install retaining ring (1).
End By: Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod - Install".
2/2(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Suggest:
For more complete manuals. Please go to
the home page.
https://www.ebooklibonline.com
If the above button click is invalid. Please
download this document first, and then
click the above link to download the
complete manual.
Thank you so much for reading
24. Product: TELEHANDLER
Model: TH350B TELEHANDLER SLD
Configuration: TH350B Telehandler SLD00001-01640 (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01749382
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00635153
Typical example
1. Install pushrods (4).
1/2(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Note: Ensure that the pushrods are installed in the original location and that the pushrods
are seated in the valve lifters correctly.
2. Install a new oil seal in the oil supply hole in the cylinder head.
Illustration 2 g00635152
Typical example
3. Put rocker shaft assembly (3) in position on the cylinder head. Make sure that the
connection for the oil supply is installed correctly into the oil seal.
Note: Ensure that the adjustment screws are properly seated in the ends of pushrods (4).
Note: It may be necessary to loosen the adjustment screws on each rocker arm. This will
help prevent a bent valve or a bent pushrod during the installation of the rocker shaft.
4. Lubricate nuts (1) and bolt (2) with clean engine oil.
5. Install nuts (1) and bolt (2).
6. Alternately tighten the nuts and the bolt. Start from the center and work toward the outside.
Tighten the nuts and the bolt on an aluminum bracket to a torque of 40 N·m (30 lb ft).
Tighten the nuts and the bolt on a cast iron or a steel bracket to a torque of 75 N·m
(55 lb ft).
7. Adjust the inlet valve lash to 0.20 mm (0.008 inch) and adjust the exhaust valve lash to
0.45 mm (0.018 inch). Refer to Testing and Adjusting, "Air Inlet and Exhaust System" for
more information on adjusting the valve lash.
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
2/2(W)
w
2022/5/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...