This document provides instructions for removing and installing various engine components on a Caterpillar 3054E engine, including the cylinder head, rocker shaft, lifters, and camshaft. The procedures describe cleaning parts, lubricating bolts, and torquing fasteners to the specified values. Special tools may be required and safety precautions are noted regarding containing fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The procedures describe removing parts, cleaning them, installing new seals or lubricating components with oil, and tightening fasteners to the specified torques. Special tools may be required for some steps.
This document provides instructions for removing and installing various parts of a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The removal process for the cylinder head involves gradually loosening bolts in a specified order, lifting the head off, and inspecting dowels and bolts. The installation process specifies cleaning surfaces, torquing bolts in a sequence, and using tools to further tighten bolts. Lifter removal uses a magnet tool, while installation ensures the lifters are seated correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The procedures describe removing parts, cleaning them, installing new seals or lubricating components, and tightening fasteners to the specified torques. Safety notices are included to warn technicians about containing fluids and preventing contaminants.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The procedures describe removing parts, cleaning them, installing new seals or lubricating components with oil, and tightening fasteners to the specified torques. Special tools may be required for some steps.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The procedures describe removing parts, cleaning them, installing new seals or lubricating components, and tightening fasteners to the specified torques. Safety notices are included to warn technicians about containing fluids and preventing contaminants.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The procedures describe removing parts, cleaning them, installing new seals or lubricating components with oil, and tightening fasteners to the specified torques. Special tools may be required for some steps.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a specified order, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a particular sequence, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The procedures describe removing parts, cleaning them, installing new seals or lubricating components with oil, and tightening fasteners to the specified torques. Special tools may be required for some steps.
This document provides instructions for removing and installing various parts of a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The removal process for the cylinder head involves gradually loosening bolts in a specified order, lifting the head off, and inspecting dowels and bolts. The installation process specifies cleaning surfaces, torquing bolts in a sequence, and using tools to further tighten bolts. Lifter removal uses a magnet tool, while installation ensures the lifters are seated correctly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The procedures describe removing parts, cleaning them, installing new seals or lubricating components, and tightening fasteners to the specified torques. Safety notices are included to warn technicians about containing fluids and preventing contaminants.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The procedures describe removing parts, cleaning them, installing new seals or lubricating components with oil, and tightening fasteners to the specified torques. Special tools may be required for some steps.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The procedures describe removing parts, cleaning them, installing new seals or lubricating components, and tightening fasteners to the specified torques. Safety notices are included to warn technicians about containing fluids and preventing contaminants.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the cylinder head, rocker shaft and pushrods, lifter group, and camshaft. The procedures describe removing parts, cleaning them, installing new seals or lubricating components with oil, and tightening fasteners to the specified torques. Special tools may be required for some steps.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a specified order, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a particular sequence, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a particular sequence, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a particular sequence, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a particular sequence, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a particular sequence, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3054 engine. The key steps are:
1. Drain coolant and remove components attached to the cylinder head like the air inlet manifold, exhaust manifold, fuel injection nozzles, and rocker arm assembly.
2. Gradually loosen the 22 cylinder head bolts in reverse tightening order.
3. Attach a lifting device and carefully remove the cylinder head, weighing 41 kg/90 lb. Remove the cylinder head gasket and note dowel pin locations.
4. Check for cylinder head distortion by aligning a straight edge with an installed bolt.
This document provides instructions for removing and installing the valve mechanism cover, rocker shaft, and pushrods on a Caterpillar 3054 engine. Key steps include removing the valve cover nuts and gasket, removing the rocker shaft nuts and brackets to take off the assembly, and installing new seals before reinstalling the removed components in reverse order and tightening to the specified torques.
This document provides instructions for removing and installing the valve mechanism cover, rocker shaft, and pushrods on a Caterpillar 3054 engine. Key steps include removing the valve cover nuts and gasket, removing the rocker shaft nuts and bolts, and removing the pushrods. Reinstallation involves installing new gaskets and seals, lubricating fasteners, and tightening nuts and bolts to the specified torques.
This document provides instructions for removing and installing the valve mechanism cover, rocker shaft, and pushrods on a Caterpillar 3054 engine. Key steps include removing the valve cover nuts and gasket, removing the rocker shaft nuts and bolts, and removing the pushrods. Reinstallation involves installing new seals, lubricating components, and tightening fasteners to the specified torques.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3054 engine. The key steps are:
1. Drain coolant and remove components attached to the cylinder head like the air inlet manifold, exhaust manifold, fuel injection nozzles, and rocker arm assembly.
2. Gradually loosen the 22 cylinder head bolts in reverse tightening order.
3. Attach a lifting device and carefully remove the cylinder head, weighing 41 kg/90 lb. Remove the cylinder head gasket and note dowel pin locations.
4. Check for cylinder head distortion by aligning a straight edge with an installed bolt.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3054 engine. The key steps are:
1. Drain coolant and remove components attached to the cylinder head like the air inlet manifold, exhaust manifold, fuel injection nozzles, and rocker arm assembly.
2. Gradually loosen the 22 cylinder head bolts in reverse tightening order.
3. Attach a lifting device and carefully remove the cylinder head, weighing 41 kg/90 lb. Remove the cylinder head gasket and note dowel pin locations.
4. Check for cylinder head distortion by aligning a straight edge with an installed bolt.
The document provides instructions for removing and installing various components of a 3406C diesel engine cylinder head assembly, including the cylinder head, spacer plate, valves, valve seats, bridge dowels, valve guides, and oil pan. The removal process involves disconnecting related components and removing mounting bolts, while installation involves cleaning surfaces, installing new gaskets and seals, and tightening bolts in the specified sequence.
The document provides instructions for removing and installing various components of a 3406C diesel engine cylinder head, including the cylinder head assembly, spacer plate, valves, valve seat inserts, bridge dowels, and valve guides. The procedures involve using various tools to remove and install gaskets and seals, cleaning surfaces, and tightening bolts in a specific sequence while applying lubricants.
The document provides instructions for removing and installing various engine components of a 3406C diesel engine, including the cylinder head assembly, spacer plate, valves, valve guides, oil pan, and plate. The removal process involves draining oil, removing mounting bolts, lifting components, and extracting seals and gaskets. The installation process specifies cleaning surfaces, inserting new seals and gaskets, lowering components into place, and tightening bolts in a specific sequence while applying lubricant.
The document provides instructions for removing and installing various engine components of a 3406C diesel engine, including the cylinder head assembly, spacer plate, valves, valve guides, oil pan, and plate. The removal process involves draining oil, removing mounting bolts, lifting components, and extracting seals and gaskets. The installation process specifies cleaning surfaces, inserting new seals and gaskets, lowering components into place, and tightening bolts in a specific sequence while applying lubricant.
Massey Ferguson MF 384 S TRACTOR (- 300993) Parts Catalogue Manual Instant Do...gua6982552kun
This document contains parts listings and technical specifications for the engine of a Massey Ferguson 384 S tractor. It includes 6 pages detailing over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, cylinder head, rocker shaft, and air induction/exhaust systems. Each part is listed with its part number, quantity used, description, and any replacement or comment information.
Massey Ferguson MF 384 F TRACTOR, - 0894 Parts Catalogue Manual Instant Downl...gua6982552kun
The document is a parts catalog for a Massey Ferguson MF 384 F tractor engine. It lists over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft and other components. Each part is given a reference number, part number, quantity and description, along with any replacement or additional part information.
Caterpillar Cat TH350B Telehandler (Prefix SLD) Service Repair Manual Instant...gua6982552kun
This document provides instructions for disassembling and assembling parts of a TELEHANDLER Model TH350B powered by a 3054E engine. The summary includes:
1) Instructions are provided to remove and install the front gear group, housing, valve mechanism cover, rocker shaft assembly, and pushrods of the 3054E engine.
2) Detailed steps and illustrations guide the disassembly and reassembly of each component, including any required tools.
3) Proper cleaning and installation of seals and gaskets is emphasized to prevent contamination.
Caterpillar Cat TH340B Telehandler (Prefix SLC) Service Repair Manual Instant...gua6982552kun
This document provides instructions for removing and installing various components of a TH340B Telehandler including the flywheel housing, crankshaft pulley, crankshaft front seal, and front cover. The flywheel housing removal procedure involves using lifting equipment to support the housing while removing setscrews. The crankshaft pulley installation ensures proper lubrication and torque of setscrews. The crankshaft front seal removal uses a puller, while installation uses a special tool and nut to push the seal into place. Front cover removal and installation requires removing/installing setscrews and ensuring a clean gasket surface.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054B engine, including:
- Removing and installing the rocker arm and shaft, which involves installing new pushrods and oil seals and adjusting valve lash.
- Removing the cylinder head, which requires removing fuel injectors, exhaust manifolds, temperature regulators, rocker arms, and pushrods before loosening bolts and lifting the head off.
- Installing the cylinder head, which involves cleaning surfaces, installing a new gasket, torquing bolts in a specific sequence, and adjusting valve lash.
- Removing and installing the valve lifters using a magnet tool to pick them up
This document provides instructions for removing and installing the camshaft gear on a Caterpillar 3054B engine. The removal process involves aligning timing marks, removing a bolt and washer, and using a puller tool. The installation involves positioning the camshaft gear properly, installing the washer and bolt, and ensuring timing marks are aligned. Tools and torque specifications are provided.
This document provides assembly instructions for various components of a TH103 Telehandler 3PN transmission, including the forward high clutch drum assembly, forward high and reverse idler shaft assembly, output shaft and third clutch assembly, reversing clutch assembly, and second clutch assembly. The instructions include cleaning and inspecting parts, installing bearings and seals, assembling clutch components like springs, discs, and plates, and securing parts with retaining rings. Tools needed include retaining ring pliers, a compressor, and driver. Temperature and positioning details are provided for proper assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar D6R track-type tractor, including:
- Removing the valve mechanism cover and gasket
- Removing the valve mechanism cover base and seal
- Removing the cylinder head by draining coolant, disconnecting harnesses and tubes, removing bolts, and lifting it off using a link bracket tool.
More Related Content
Similar to Caterpillar Cat TH460B Telehandler (Prefix SLF) Service Repair Manual Instant Download (SLF00001 and up).pdf
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a particular sequence, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a particular sequence, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a particular sequence, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the valve cover, rocker shaft, pushrods, and cylinder head. The removal and installation procedures describe loosening specific bolts and nuts in a particular sequence, removing gaskets and seals, and ensuring proper alignment of components during reassembly.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3054 engine. The key steps are:
1. Drain coolant and remove components attached to the cylinder head like the air inlet manifold, exhaust manifold, fuel injection nozzles, and rocker arm assembly.
2. Gradually loosen the 22 cylinder head bolts in reverse tightening order.
3. Attach a lifting device and carefully remove the cylinder head, weighing 41 kg/90 lb. Remove the cylinder head gasket and note dowel pin locations.
4. Check for cylinder head distortion by aligning a straight edge with an installed bolt.
This document provides instructions for removing and installing the valve mechanism cover, rocker shaft, and pushrods on a Caterpillar 3054 engine. Key steps include removing the valve cover nuts and gasket, removing the rocker shaft nuts and brackets to take off the assembly, and installing new seals before reinstalling the removed components in reverse order and tightening to the specified torques.
This document provides instructions for removing and installing the valve mechanism cover, rocker shaft, and pushrods on a Caterpillar 3054 engine. Key steps include removing the valve cover nuts and gasket, removing the rocker shaft nuts and bolts, and removing the pushrods. Reinstallation involves installing new gaskets and seals, lubricating fasteners, and tightening nuts and bolts to the specified torques.
This document provides instructions for removing and installing the valve mechanism cover, rocker shaft, and pushrods on a Caterpillar 3054 engine. Key steps include removing the valve cover nuts and gasket, removing the rocker shaft nuts and bolts, and removing the pushrods. Reinstallation involves installing new seals, lubricating components, and tightening fasteners to the specified torques.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3054 engine. The key steps are:
1. Drain coolant and remove components attached to the cylinder head like the air inlet manifold, exhaust manifold, fuel injection nozzles, and rocker arm assembly.
2. Gradually loosen the 22 cylinder head bolts in reverse tightening order.
3. Attach a lifting device and carefully remove the cylinder head, weighing 41 kg/90 lb. Remove the cylinder head gasket and note dowel pin locations.
4. Check for cylinder head distortion by aligning a straight edge with an installed bolt.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3054 engine. The key steps are:
1. Drain coolant and remove components attached to the cylinder head like the air inlet manifold, exhaust manifold, fuel injection nozzles, and rocker arm assembly.
2. Gradually loosen the 22 cylinder head bolts in reverse tightening order.
3. Attach a lifting device and carefully remove the cylinder head, weighing 41 kg/90 lb. Remove the cylinder head gasket and note dowel pin locations.
4. Check for cylinder head distortion by aligning a straight edge with an installed bolt.
The document provides instructions for removing and installing various components of a 3406C diesel engine cylinder head assembly, including the cylinder head, spacer plate, valves, valve seats, bridge dowels, valve guides, and oil pan. The removal process involves disconnecting related components and removing mounting bolts, while installation involves cleaning surfaces, installing new gaskets and seals, and tightening bolts in the specified sequence.
The document provides instructions for removing and installing various components of a 3406C diesel engine cylinder head, including the cylinder head assembly, spacer plate, valves, valve seat inserts, bridge dowels, and valve guides. The procedures involve using various tools to remove and install gaskets and seals, cleaning surfaces, and tightening bolts in a specific sequence while applying lubricants.
The document provides instructions for removing and installing various engine components of a 3406C diesel engine, including the cylinder head assembly, spacer plate, valves, valve guides, oil pan, and plate. The removal process involves draining oil, removing mounting bolts, lifting components, and extracting seals and gaskets. The installation process specifies cleaning surfaces, inserting new seals and gaskets, lowering components into place, and tightening bolts in a specific sequence while applying lubricant.
The document provides instructions for removing and installing various engine components of a 3406C diesel engine, including the cylinder head assembly, spacer plate, valves, valve guides, oil pan, and plate. The removal process involves draining oil, removing mounting bolts, lifting components, and extracting seals and gaskets. The installation process specifies cleaning surfaces, inserting new seals and gaskets, lowering components into place, and tightening bolts in a specific sequence while applying lubricant.
Similar to Caterpillar Cat TH460B Telehandler (Prefix SLF) Service Repair Manual Instant Download (SLF00001 and up).pdf (14)
Massey Ferguson MF 384 S TRACTOR (- 300993) Parts Catalogue Manual Instant Do...gua6982552kun
This document contains parts listings and technical specifications for the engine of a Massey Ferguson 384 S tractor. It includes 6 pages detailing over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, cylinder head, rocker shaft, and air induction/exhaust systems. Each part is listed with its part number, quantity used, description, and any replacement or comment information.
Massey Ferguson MF 384 F TRACTOR, - 0894 Parts Catalogue Manual Instant Downl...gua6982552kun
The document is a parts catalog for a Massey Ferguson MF 384 F tractor engine. It lists over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft and other components. Each part is given a reference number, part number, quantity and description, along with any replacement or additional part information.
Caterpillar Cat TH350B Telehandler (Prefix SLD) Service Repair Manual Instant...gua6982552kun
This document provides instructions for disassembling and assembling parts of a TELEHANDLER Model TH350B powered by a 3054E engine. The summary includes:
1) Instructions are provided to remove and install the front gear group, housing, valve mechanism cover, rocker shaft assembly, and pushrods of the 3054E engine.
2) Detailed steps and illustrations guide the disassembly and reassembly of each component, including any required tools.
3) Proper cleaning and installation of seals and gaskets is emphasized to prevent contamination.
Caterpillar Cat TH340B Telehandler (Prefix SLC) Service Repair Manual Instant...gua6982552kun
This document provides instructions for removing and installing various components of a TH340B Telehandler including the flywheel housing, crankshaft pulley, crankshaft front seal, and front cover. The flywheel housing removal procedure involves using lifting equipment to support the housing while removing setscrews. The crankshaft pulley installation ensures proper lubrication and torque of setscrews. The crankshaft front seal removal uses a puller, while installation uses a special tool and nut to push the seal into place. Front cover removal and installation requires removing/installing setscrews and ensuring a clean gasket surface.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054B engine, including:
- Removing and installing the rocker arm and shaft, which involves installing new pushrods and oil seals and adjusting valve lash.
- Removing the cylinder head, which requires removing fuel injectors, exhaust manifolds, temperature regulators, rocker arms, and pushrods before loosening bolts and lifting the head off.
- Installing the cylinder head, which involves cleaning surfaces, installing a new gasket, torquing bolts in a specific sequence, and adjusting valve lash.
- Removing and installing the valve lifters using a magnet tool to pick them up
This document provides instructions for removing and installing the camshaft gear on a Caterpillar 3054B engine. The removal process involves aligning timing marks, removing a bolt and washer, and using a puller tool. The installation involves positioning the camshaft gear properly, installing the washer and bolt, and ensuring timing marks are aligned. Tools and torque specifications are provided.
This document provides assembly instructions for various components of a TH103 Telehandler 3PN transmission, including the forward high clutch drum assembly, forward high and reverse idler shaft assembly, output shaft and third clutch assembly, reversing clutch assembly, and second clutch assembly. The instructions include cleaning and inspecting parts, installing bearings and seals, assembling clutch components like springs, discs, and plates, and securing parts with retaining rings. Tools needed include retaining ring pliers, a compressor, and driver. Temperature and positioning details are provided for proper assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar D6R track-type tractor, including:
- Removing the valve mechanism cover and gasket
- Removing the valve mechanism cover base and seal
- Removing the cylinder head by draining coolant, disconnecting harnesses and tubes, removing bolts, and lifting it off using a link bracket tool.
This document provides instructions for disassembling and assembling the torque divider of a D6G2 track-type tractor. It describes removing over 30 individual components of the torque divider including gears, seals, bearings, and housing pieces. Detailed illustrations and notes are provided to caution safe operation and containment of fluids. Proper cleaning and inspection of all parts is emphasized before reassembling the torque divider using the provided tools.
The document provides instructions for disassembling and assembling the piston pump steering system on a D5R2 track-type tractor. It details 39 steps to disassemble components such as the piston pump, valves, housing, pistons, and seals. It then lists 36 steps for reassembling these components in reverse order. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
This document provides instructions for removing and installing various components of a 3126B engine for a Caterpillar D5N track-type tractor, including the camshaft, camshaft gear, camshaft bearings, engine oil pan, and piston cooling jets. The procedures describe draining fluids, using required tools, cleaning and applying sealant to mating surfaces, and torquing bolts to specified values. Safety notices are provided to contain fluids and prevent contamination.
This document provides assembly instructions for the piston pump on the left side of a D5K XL track-type tractor. It includes 40 steps to assemble various components like springs, seals, valves, plates, and housing pieces. Special tools are required and safety precautions mentioned, like following procedures carefully when assembling spring-loaded parts to avoid injury. Measurements must be taken to determine the correct shim thickness for the rotating group.
This document provides instructions for installing a cylinder head on a D4K2 XL track-type tractor. It describes cleaning and inspecting the cylinder head and cylinder block faces and installing dowels. It outlines torquing the bolts that secure the cylinder head in the correct sequence. Proper lubrication and alignment of the cylinder head gasket is emphasized to avoid leaks or damage.
This document provides instructions for removing and installing the valve mechanism cover on a Caterpillar D4K2 XL track-type tractor powered by a C4.4 engine. The procedure involves removing bolts and brackets to access the cover, then removing and installing a new gasket before reinstalling the cover and related components. Separate sections provide details on disassembling and assembling the rocker shaft and related parts.
Caterpillar Cat CB564D Vibratory Compactor (Prefix D4M) Service Repair Manual...gua6982552kun
This document provides instructions for removing and installing the flywheel housing on a Caterpillar 3054C engine. The flywheel housing must first be supported with lifting equipment as it weighs approximately 39 kg. Setscrews securing the housing must be removed, and the housing can then be lifted off while tapping it with a soft hammer if needed. Cleaning and inspection steps are described before reinstalling the housing using setscrews, ensuring proper torque is applied.
This document provides instructions for removing and installing the front gear group of a C15 Industrial Engine N5F. Key steps include removing the front housing, camshaft gear, and various gears and plates. Installation involves cleaning parts, applying thread lock to bolts, and adjusting backlash between gears. Tightening torques and sequences are specified.
This document provides instructions for removing and installing an engine oil filter base on a C13 Industrial Engine N3F. The removal procedure involves draining the engine oil, then removing hoses, fittings, bolts and the oil filter base. Several internal components like springs and plungers must also be removed from the base. For installation, the base and components are reinstalled in reverse order, applying lubricant to seals and filters. Torque specifications are provided for several installation steps.
The document provides instructions for disassembling and assembling various components of an C13 Industrial Engine LGK00001-UP, including the front cover, gear group, front housing, accessory drive, valve mechanism cover base, rocker shaft, and pushrods. The steps describe removing and installing parts like bolts, gears, covers, and shafts. Precautions are provided to keep parts clean and ensure proper alignment of timing marks during assembly.
This document provides instructions for removing and installing a fuel injector from an industrial engine. It describes required tools, safety notices, and step-by-step procedures for removing the fuel injection lines, disconnecting electrical connectors, and removing the fuel injector. Instructions are also given for installing a new fuel injector, reconnecting lines and connectors, and priming the fuel system.
This document provides instructions for removing a flywheel housing from a 3512E Marine Engine. Key steps include:
1) Removing components attached to the housing like the starting motor and exhaust elbow
2) Installing timing tools to lock the camshafts and crankshaft in place
3) Using puller tools to remove the camshaft drive gears
4) Attaching lifting brackets and removing bolts to lift the heavy flywheel housing off the engine block
5) Cleaning mating surfaces on the housing and cylinder block after removal
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Caterpillar Cat TH460B Telehandler (Prefix SLF) Service Repair Manual Instant Download (SLF00001 and up).pdf
1. Product: TELEHANDLER
Model: TH460B TELEHANDLER SLF
Configuration: TH460B Telehandler SLF00001-UP (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01749382
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00635153
Typical example
1. Install pushrods (4).
1/2(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
2. Note: Ensure that the pushrods are installed in the original location and that the pushrods
are seated in the valve lifters correctly.
2. Install a new oil seal in the oil supply hole in the cylinder head.
Illustration 2 g00635152
Typical example
3. Put rocker shaft assembly (3) in position on the cylinder head. Make sure that the
connection for the oil supply is installed correctly into the oil seal.
Note: Ensure that the adjustment screws are properly seated in the ends of pushrods (4).
Note: It may be necessary to loosen the adjustment screws on each rocker arm. This will
help prevent a bent valve or a bent pushrod during the installation of the rocker shaft.
4. Lubricate nuts (1) and bolt (2) with clean engine oil.
5. Install nuts (1) and bolt (2).
6. Alternately tighten the nuts and the bolt. Start from the center and work toward the outside.
Tighten the nuts and the bolt on an aluminum bracket to a torque of 40 N·m (30 lb ft).
Tighten the nuts and the bolt on a cast iron or a steel bracket to a torque of 75 N·m
(55 lb ft).
7. Adjust the inlet valve lash to 0.20 mm (0.008 inch) and adjust the exhaust valve lash to
0.45 mm (0.018 inch). Refer to Testing and Adjusting, "Air Inlet and Exhaust System" for
more information on adjusting the valve lash.
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
2/2(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Product: TELEHANDLER
Model: TH460B TELEHANDLER SLF
Configuration: TH460B Telehandler SLF00001-UP (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01645897
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
A. Disconnect the electrical connections at the battery.
B. Drain the coolant system. If the engine uses Diesel Engine Antifreeze/Coolant (DEAC),
refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change".
If the engine uses Extended Life Coolant (ELC), refer to Operation and Maintenance
Manual, "Cooling System Coolant (ELC) - Change".
C. Remove the air inlet manifold. Refer to Disassembly and Assembly, "Air Inlet Manifold -
Remove".
D. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
E. Remove the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection
Nozzles - Remove".
F. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
G. Remove the water outlet manifold. Refer to Disassembly and Assembly, "Water Outlet
Manifold - Remove".
H. Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly,
"Rocker Arm and Shaft - Remove".
1/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 1 g00550160
Typical example
Illustration 2 g00550162
1. Gradually loosen 22 cylinder head bolts (1) in the reverse order that is shown in Illustration
2. This will help prevent distortion of the cylinder head.
2/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 3 g00550163
Typical example
2. Attach a suitable lifting device to cylinder head (2). Carefully lift cylinder head (2) off the
engine block. The weight of the cylinder head is 41 kg (90 lb).
NOTICE
Place the cylinder head on a surface that will not scratch the face of the
cylinder head.
Illustration 4 g00550165
3. Remove cylinder head gasket (3) .
4. Note the location of dowels (4) on each end of the cylinder block. Dowels (4) hold cylinder
head gasket (3) in place while cylinder head (2) is installed.
3/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 5 g00741112
5. Align straight edge (7) with bolt (6) in order to check for distortion. If there is a visible
reduction in the diameter of thread (8) that has not been in engagement with the cylinder
block, the bolts must be replaced.
4/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Product: TELEHANDLER
Model: TH460B TELEHANDLER SLF
Configuration: TH460B Telehandler SLF00001-UP (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01645901
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6238 Guide Bolt 2
B 8T-3052 Degree Wheel 1
1. Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure
that there is no debris in the cylinder bores.
Illustration 1 g00550165
1/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. 2. Place cylinder head gasket (3) on dowels (4) on top of the cylinder block. The cylinder head
gasket (3) is stamped "FRONT TOP". Do not use any sealant or compound on the cylinder
head gasket.
3. Install Tool (A) in positions 15 and 20 in the cylinder block. Refer to Illustration 4.
Illustration 2 g00550163
Typical example
4. Attach a suitable lifting device to cylinder head (2) .
5. Place cylinder head (2) on the cylinder block. Ensure that the cylinder head is positioned on
dowels (4) and that cylinder head gasket (3) is positioned correctly.
6. Remove Tool (A) .
Illustration 3 g00550160
Typical example
7. Lubricate cylinder head bolts (1) with clean engine oil.
2/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 4 g00550162
8. Gradually tighten all of the bolts (1 through 22) in a numerical sequence to a torque of 110
N·m (80 lb ft).
9. Tighten all of the bolts (1 through 22) again in a numerical sequence to a torque of 110 N·m
(80 lb ft).
10. Place an index mark on the bolts and use Tool (B) in order to further tighten the bolts. Refer
to illustration 4.
a. Turn the short bolts that are marked with an "S" for an additional 150 degrees (2.5
flats).
b. Turn the medium length bolts that are marked with an "M" for an additional 180
degrees (3.0 flats).
c. Turn the long bolts that are marked with an "L" for an additional 210 degrees (3.5
flats).
End By:
a. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Arm and
Shaft - Install".
b. Install the water outlet manifold. Refer to Disassembly and Assembly, "Water Outlet
Manifold - Install".
c. Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove
and Install".
d. Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection
Nozzles - Install".
e. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
f. Install the inlet manifold. Refer to Disassembly and Assembly, "Air inlet Manifold -Install".
3/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. g. Fill the coolant system. If the engine uses Extended Life Coolant (ELC), refer to Operation
and Maintenance Manual, "Cooling System Coolant (ELC) - Change". If the engine uses
Diesel Engine Antifreeze/Coolant (DEAC), refer to Operation and Maintenance Manual,
"Cooling System Coolant (DEAC) - Change".
h. Connect the electrical connections at the battery.
4/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Product: TELEHANDLER
Model: TH460B TELEHANDLER SLF
Configuration: TH460B Telehandler SLF00001-UP (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01745933
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 1 g00540954
1. Use Tooling (A) to remove lifters (1).
Note: Ensure that the lifters are marked with the appropriate cylinder number for
installation purposes.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 2 g00540954
1. Use Tooling (A) to install lifters (1).
Note: Ensure that the lifters are seated correctly and that the lifters are in the correct
cylinders.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install".
3/3(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Product: TELEHANDLER
Model: TH460B TELEHANDLER SLF
Configuration: TH460B Telehandler SLF00001-UP (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01164529
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrods - Remove".
B. Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Remove".
C. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
D. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Turn the engine upside-down so the valve lifters are held in a position away from the
camshaft.
Illustration 1 g00546803
2. Remove thrust washer (1). Make a note of the location of the hollow dowel (X) for
installation purposes.
Illustration 2 g00546869
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. 3. Carefully remove camshaft (2) from the engine.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00546869
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
Note: Ensure that camshaft (2) is clean. Lubricate camshaft (2) with clean engine oil prior
to installation.
1. Carefully install camshaft (2) in the engine.
3/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 4 g00546803
2. Put thrust washer (1) in position. Make sure that thrust washer (1) is aligned with hollow
dowel (X) .
End By:
a. Install the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
b. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
c. Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Install".
d. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrods - Install".
4/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Product: TELEHANDLER
Model: TH460B TELEHANDLER SLF
Configuration: TH460B Telehandler SLF00001-UP (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i03140046
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A
1U-6671 Puller Gp 1
8S-4712 Bolt 2
1P-0510 Driver Group 1
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
b. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
1/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 1 g00541128
1. Rotate the crankshaft until the timing marks on the crankshaft gear, the camshaft gear, and
the fuel injection pump gear are aligned, as shown.
Note: The timing marks on the idler gear may not be aligned. This is caused by the
difference in the speed of the rotation of the idler gear.
Illustration 2 g00541130
2. Remove bolt (1) and the washer from the camshaft gear (2).
2/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 3 g00541131
3. Install Tooling (A) and remove camshaft gear.
Note: Do not lose the key from the camshaft gear.
4. Inspect the camshaft gear for wear and damage. Replace the gear, if necessary.
Installation Procedure
Illustration 4 g00541130
1. Install camshaft gear (2) in the front housing.
Note: When you install the camshaft gear, ensure that the teeth that have the timing marks
are facing toward the front. Also, ensure that the key is aligned properly in the keyway. If
necessary, tap the gear with a soft hammer in order to seat the key in the keyway.
2. If necessary, remove the idler gear in order to align the gear teeth correctly.
3. Install the washer and bolt (1) on the camshaft gear. Tighten bolt (1) to a torque of 95 N·m
(70 lb ft).
Note: Ensure that the timing marks on the camshaft gear, the crankshaft gear, and the fuel
injection pump gear are aligned.
3/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 4. If a new camshaft gear is used, check the backlash of the camshaft gear. The minimum
backlash for a new gear is 0.08 mm (0.003 inch).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
4/4(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Product: TELEHANDLER
Model: TH460B TELEHANDLER SLF
Configuration: TH460B Telehandler SLF00001-UP (MACHINE) POWERED BY 3054E Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i06043534
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
A. If the engine is equipped with a balancer, remove the balancer. Refer to Disassembly and
Assembly, "Balancer - Remove". If the engine is not equipped with a balancer, remove the
engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove" for the
correct procedure.
B. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Suggest:
For more complete manuals. Please go to
the home page.
https://www.ebooklibonline.com
If the above button click is invalid. Please
download this document first, and then
click the above link to download the
complete manual.
Thank you so much for reading
24. Illustration 1 g01270437
1. Inspect camshaft bearing (1) . Refer to Specifications, "Camshaft Bearings" for more
information.
2. For worn or damaged camshaft bearing (1) use Tooling (A) in order to remove the camshaft
bearing from the cylinder block.
Note: Remove the camshaft bearing from the front of the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the bearing housing in the cylinder block. Ensure that the oil holes in the bearing
housing are free from debris.
2/3(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 2 g01266512
2. Lubricate the bearing housing in the cylinder block with clean engine oil.
3. Accurately align two Oil Holes (X) in camshaft bearing (1) with the two oil holes in the
cylinder block.
Note: Groove (Y) in the camshaft bearing must be to the top of the cylinder block.
4. Use Tooling (A) in order to install camshaft bearing (1) into the cylinder block. Install the
camshaft bearing so that the front edge of the bearing is flush with the face of the recess in
the cylinder block.
Note: Ensure that all oil holes are correctly aligned. If the oils are not correctly aligned, the
camshaft bearing should be removed.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install"
for the correct procedure.
b. If the engine is equipped with a balancer, install the balancer. Refer to Disassembly and
Assembly, "Balancer - Install". If the engine is not equipped with a balancer, install the
engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install" for the
correct procedure.
3/3(W)
w
2022/5/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...