Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j06389 09655)

Service Repair Manual
Models
966C WHEEL LOADER

Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966C WHEEL LOADER 76J
Configuration: 966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
966 WHEEL LOADER POWER TRAIN
Media Number -REG01117-02 Publication Date -01/04/1992 Date Updated -10/10/2001
Axles
SMCS - 3259-11; 3259-12
Remove Axles
1. Remove plug (3). Drain the oil from the final drive.
2. Remove bolts (1). Remove cover assembly (2) from the final drive planet carrier.
3. Pull axle (4) and gear part way out of the final drive.
NOTE: If the axle can not be removed, move the machine a small amount to the front or rear until
the axle can be pulled from the final drive.
1/3
966C WHEEL LOADER 76J06389-09655 (MACHINE) POWERED BY 3306 ENGI...
2020/4/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

4. Fasten a hoist to the axle. Remove axle (4). The weight of the axle is 55 lb. (25 kg).
5. Remove retainer ring (6). Remove gear (5) and washer (7) from the axle.
Install Axles
1. Make sure the axles are clean and free of all dirt or foreign material.
2. Put washer (2) [with the steel side next to the gear] and gear (1) in position on the axle. Install
retainer ring (3).
3. Fasten a hoist to the axle. Put axle (4) in position in the final drive.
2/3
2020/4/13

4. Remove the retainer ring from the axle. Pull gear (1) part way off the axle. Put a piece of pipe
(5) which has a 2" (5.1 cm) outside diameter and is approximately 24 in. (61 cm) long in the gear
as shown. Push down on the pipe and slide the axle into position.
5. Remove the pipe. Slide gear (1) into position in the final drive planetary. Install the retainer ring
on the axle.
6. Turn the flat sides of the three shafts (7) as shown to give clearance for counterbore in cover.
7. Check the O-ring seal in the cover assembly for wear or damage. If necessary, make a
replacement.
NOTICE
If the cover does not fit flat up against the final drive without force,
remove the cover and do Step 6 again.
8. Install cover assembly (6) on the final drive planetary carrier.
9. Fill the final drive with oil to the correct level. See LUBRICATION AND MAINTENANCE
GUIDE.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 13 23:37:08 UTC+0800 2020
3/3
2020/4/13

Shutdown SIS
Previous Screen
Final Drive Planet Carriers
SMCS - 4092-11; 4092-12
Remove Final Drive Planet Carriers
start by:
a) remove axles
1. Remove two bolts (1) (180° apart). Install two 5/8"-11 NC guide bolts in their place.
2. Fasten tooling (A) and a hoist to the final drive planet carrier as shown. Remove the remainder
of the bolts that hold the final drive planet carrier to the wheel assembly.
1/2
2020/4/13

3. Install two 1/2"-13 NC forcing screws (2) and loosen the final drive planet carrier from the
wheel assembly.
4. Remove final drive planet carrier (3). The weight of the carrier is 100 lb. (45 kg).
Install Final Drive Planet Carrier
1. Check the O-ring on the back of the planet carrier for damage or wear. If necessary, make a
replacement.
2. Install two 5/8"-11 NC guide bolts (2) in the wheel assembly 180° apart as shown.
3. Fasten tooling (A) and a hoist to the planet carrier. Put final drive planet carrier (1) in position
in the wheel assembly. Install the bolts that hold it. Remove guide bolts (2). Install the remainder
of the bolts. Tighten the bolts to a torque of 150 ± 20 lb.ft. (205 ± 27 N·m).
end by:
a) install axles
Mon Apr 13 23:38:03 UTC+0800 2020
2/2
2020/4/13

Shutdown SIS
Previous Screen
Final Drive Planet Carriers
SMCS - 4092-15; 4092-16
Disassemble Final Drive Planet Carriers
start by:
a) remove final drive planet carriers
1. Remove shafts (1) from the carrier.
2. Remove three gears (2) and twelve washers.
3. Remove retainer ring (4) from the shafts.
4. Remove two bearings (3) and spacer (5) from the gears.
Assemble Final Drive Planet Carriers
1/2
2020/4/13

1. Install bearings (1) and (3) and spacers (2) in gears (4).
2. Install retainer rings (5) on the shaft.
3. Put gears and washers in position in the carrier with steel washers (7) next to the gears and
bronze washers (8) between the carrier and steel washers.
4. Install shafts (6) in the carrier.
end by:
a) install final drive planet carriers
Mon Apr 13 23:38:59 UTC+0800 2020
2/2
2020/4/13

Shutdown SIS
Previous Screen
Final Drive Ring Gears And Hubs
SMCS - 4054; 4055-12; 4055-11
Remove Final Drive And Gears And Hubs
start by:
a) remove tires and rims (front or rear)
b) remove final drive planet carriers
1. Remove lockwire (2). Remove bolts (1) from nut (3).
1/5
2020/4/13

2. Fasten tool (A) and a hoist to the wheel assembly as shown. Put an up force on the wheel
assembly with the hoist.
3. Use tooling (B) to remove nut (3) from the spindle.
4. Use two persons to remove ring gear (4) and hub from the spindle. The weight of the ring gear
and hub is 80 lb. (36 kg).
5. Remove bolts (5). Remove locks (6) and plates and remove hub assembly (7) from the ring
gear.
6. Use tooling (C) to remove bearing cone (8) from the hub.
2/5
2020/4/13

Install Final Drive Ring Gears And Hubs
1. Heat the bearing cone to a maximum temperature of 275° (135°C). Install bearing cone (1) on
the hub.
2. Put hub assembly (2) in position in the ring gear.
3. Install plates (3), locks and bolts that hold the hub in the ring gear.
3/5
2020/4/13

4. Use two persons to put ring gear (4) and hub in position on the spindle.
5. Install nut (5) on the spindle. Remove tool (A) and the hoist from the wheel assembly.
6. Make an adjustment to the wheel bearings as follows:
a) Use an 8 in. (20.3 cm) long torque wrench (9S7354) on the wheel stud to slowly turn the wheel
assembly while nut (5) is tightened with tooling (B). Tighten nut (5) until it takes a torque of 160
± 50 lb.in. (18.1 ± 5.7 N·m) to turn the wheel assembly one complete revolution.
NOTE: Make sure the torque wrench is installed on the wheel stud so it is in line with the center
of the wheel as shown.
b) Loosen nut (5). Tighten nut (5) again until it takes a torque of 75 ± 25 lb.in. (8.5 ± 2.8 N·m) to
slowly turn the wheel assembly one complete revolution with an 8 in. (20.3 cm) torque wrench
(9S7354) at the wheel stud.
NOTE: For torque wrenches of different lengths use the following formula for the correct torque:
4/5
2020/4/13

C is the torque wrench reading.
A is the length of the torque wrench.
B is the distance from the center of the axle housing to the wheel stud.
T is torque to turn the wheel assembly.
T=160 ± 50 lb.in. (18.1 ± 5.7 N·m) for Step (a) and 75 ± 25 lb.in. (8.5 ± 2.8 N·m) for Step (b).
7. Install bolts (7) in the hub assembly. If necessary, turn nut (5) in a clockwise direction until the
holes in the nut are in alignment with the holes in the hub assembly. Install lockwire (6) through
the bolts.
end by:
a) install final drive planet carriers
b) install tires and rims (front or rear)
Mon Apr 13 23:39:55 UTC+0800 2020
5/5
2020/4/13

Shutdown SIS
Previous Screen
Wheels, Bearings And Duo-Cone Seals
SMCS - 4208-11; 4208-12
Remove Wheels, Bearings And Duo-Cone Seals
start by:
a) remove final drive ring gears and hubs
1. Use tool (A) and a hoist to remove wheel assembly (1) from the spindle. The weight of the
wheel assembly is 330 lb. (149 kg).
2. Remove Duo-Cone seal (2) from the wheel assembly.
1/4
2020/4/13

3. Remove bolts (3) and locks. Use two persons to remove brake drum (4) from the wheel
assembly. The weight of the brake drum is 100 lb. (45 kg).
4. Remove bearing cups (5) from the wheel assembly.
5. Remove bearing cone (7) from the spindle.
6. Remove Duo-Cone seal (6) from the retainer.
7. If necessary, remove locks, bolts and bars (8). Remove retainer (9) from the spindle. Remove
the O-ring seal from the back of the retainer.
Install Wheels, Bearings And Duo-Cone Seals
1. If retainer was removed, install O-ring seal on the back of the retainer. Put retainer in position
on the spindle and install the bars, locks and bolts that hold it.
2/4
2020/4/13

2. Make sure the rubber torus seals are clean and dry. Make sure all metal surfaces that make
contact with the rubber torus seals are clean and dry. Use tool (A) to install the Duo-Cone seal in
the retainer. Put a small amount of clean SAE 30 oil on the surfaces of the metal seals that make
contact with each other.
3. Install bearing cone (1) on the spindle.
4. Lower the temperature of the bearing cups. Install bearing cups (2) in the wheel assembly.
5. Use two persons to install brake drum (4) on the wheel assembly. Install locks and bolts (3).
3/4
2020/4/13

6. Make sure rubber torus seals are clean and dry. Make sure all metal surfaces that make contact
with the rubber torus seals are clean and dry. Use tool (A) to install the Duo-Cone seal in the
wheel assembly. Put a small amount of clean SAE 30 oil on the surfaces of the metal seals that
make contact with each other.
7. Fasten tool (B) and a hoist to the wheel assembly. Put wheel assembly (5) in position on the
spindle.
end by:
a) install final drive ring gears and hubs
Mon Apr 13 23:40:51 UTC+0800 2020
4/4
2020/4/13

Shutdown SIS
Previous Screen
Brake Shoes
SMCS - 4253-12; 4253-11
Remove Brake Shoes
start by:
a) remove wheels, bearings and Duo-Cone seals
1. Remove covers (1) from the spindle.
2. Use an acceptable brake tool to remove springs (2) from the brake shoes.
1/3
2020/4/13

3. Remove lockwire (5). Loosen bolts (3) approximately .50 in. (12.7 mm).
4. Remove springs (4) from the pins.
5. Remove retainers (7) and felt washers.
6. Remove pins (6). Remove brake shoes (8). Remove springs, retainers and felt washers from the
other end of pins (6).
Install Brake Shoes
1. Install the felt washers, retainers and springs on one end of pins (2).
2. Put brake shoes (3) in position on the spider and bearing assembly and install pins (2).
3. Install felt washers and retainers (1) on the pins.
2/3
2020/4/13

4. Install springs (5) on the pins.
5. Tighten bolts (4). Make sure the holes in the pins are in alignment with the bolts before the
bolts are tightened.
6. Use an acceptable brake tool (6) to install springs (7) on the brake shoes.
7. Install covers (8) on the spindle.
NOTE: After the final drive ring gears and hubs have been installed, make an adjustment to the
brakes. See BRAKE ADJUSTMENT, 966C AIR SYSTEM AND BRAKES.
end by:
a) install wheels, bearings and Duo-Cone seals
Mon Apr 13 23:41:46 UTC+0800 2020
3/3
2020/4/13

Shutdown SIS
Previous Screen
Wheel Spindles
SMCS - 4205-12; 4205-11
Remove Wheel Spindles
start by:
a) remove brake shoes
1. Turn slack adjuster (3) to release any force on pin (1).
2. Remove retainer ring (2) from the brake camshaft.
3. Remove brake camshaft (5). Remove washers (4) from between the bracket assembly and slack
adjuster assembly and from between the brake camshaft and spindle housing.
1/4
2020/4/13

Make sure the air pressure in the brake system is zero before any lines
are disconnected.
4. Disconnect air lines (6) from the chamber assembly.
5. Remove bolts (9). Remove bracket assembly (8), slack adjuster assembly and chamber
assembly from the spindle assembly as a unit.
6. Fasten a hoist to the wheel spindle assembly. Remove nuts (7) and washers. Remove wheel
spindle assembly (10). The weight of the wheel spindle assembly is 100 lb. (45 kg).
7. Remove O-ring seal (13) from the spindle.
2/4
2020/4/13

8. Use four 1/2"-13 NC forcing screws to remove spider and bearing assembly (12) from spindle
(11).
9. Remove sleeve (14), lip seal and bearing from the spider.
Install Wheel Spindles
1. Use tooling (A) to install sleeve (3) in the spider. Use tooling (A) to install bearing and lip seal
in the opposite side of the spider. Install the seal with the lip toward the bearing.
2. Install spindle (4) in spider and bearing assembly (2). Put 1P808 General Purpose Lubricant in
the bearing and bore of the spider assembly.
3. Install O-ring seal (1) on the spindle.
4. Fasten a hoist to the wheel spindle assembly. Install wheel spindle assembly (5) on the axle
housing. Install the washers and nuts that hold it. Tighten the nuts to a torque of 345 ± 30 lb.ft.
(465 ± 40 N·m).
3/4
2020/4/13

5. Install bracket assembly (7), slack adjuster assembly and chamber assembly on the spindle
assembly as a unit.
6. Connect air lines (6) to the chamber assembly.
7. Install washer (8) on the brake camshaft. Install brake camshaft (9) in spider and bracket
assemblies. Install washer and slack adjuster assembly (10) on brake camshaft (9). Install the
retainer ring on the brake camshaft.
end by:
a) install brake shoes
Mon Apr 13 23:42:42 UTC+0800 2020
4/4
2020/4/13

Shutdown SIS
Previous Screen
Front Differential And Carrier
SMCS - 3258-12; 3258-11
Remove Front Differential And Carrier
start by:
a) remove axles (front only)
1. Remove plug (1). Drain the oil from the front axle housing.
2. Remove spider and bearing assembly (4) from the front drive shaft (3) and differential pinion
shaft.
1/4
2020/4/13

3. Remove yoke (2) from the differential pinion shaft.
Make sure the air pressure in the brake system is zero before any lines
are disconnected.
4. Disconnect three lines (5) from the tee fitting.
5. Disconnect three lines (6) from the quick release valve.
6. Disconnect clips (7) from each side of the axle housing and pull the air lines clear of the
differential and carrier.
7. Fasten tooling (A) to the front differential and carrier as shown. Remove bolts (9). Install two
1/2"-13 NC forcing screws and remove differential and carrier (8) from the axle housing. The
weight of the differential and carrier is 350 lb. (158 kg).
Install Front Differential And Carrier
2/4
2020/4/13

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

1. Fasten tooling (A) to the differential and carrier as shown. Put differential and carrier (1) in
position in the axle housing. Install the bolts that hold it. Tighten the bolts to a torque of 195 ± 18
lb.ft. (265 ± 24 N·m).
2. Connect three air lines (2) to the tee fitting.
3. Connect three air lines (3) to the quick release valve.
4. Connect the clips that hold the air lines in position on the axle housing.
5. Install yoke (4) on the differential pinion shaft.
3/4
2020/4/13

6. Install spider and bearing assembly (5) on the yoke and front drive shaft. Tighten the bolts to a
torque of 100 ± 10 lb.ft. (135 ± 14 N·m).
7. Install the drain plug and fill the front axle housing with oil to the correct level. See
LUBRICATION AND MAINTENANCE GUIDE.
end by:
a) install axles (front only)
Mon Apr 13 23:43:38 UTC+0800 2020
4/4
2020/4/13

Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j06389 09655)

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Similar to Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j06389 09655)

Similar to Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j06389 09655) (20)

More from fjsjjekdkme

More from fjsjjekdkme (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j06389 09655)