This document provides instructions for disassembling the transmission and torque converter of a 924HZ wheel loader. It outlines 48 steps to remove various components such as housing assemblies, gears, clutches, seals, bearings and other parts. Precautions are listed to prevent fluid loss and entry of contaminants. Required tools include lever pullers, jack stands, retaining ring pliers, drivers, compressors and other specialized equipment to separate components in a clean and safe manner.
This document provides instructions for disassembling the transmission and torque converter of wheel loader models 924H and 924HZ. It outlines 34 steps to fully disassemble the components, including removing housing assemblies, gears, bearings, seals, plates, discs, pistons, springs, and other parts. Precautions are provided regarding fluid containment, cleanliness, and safety when releasing spring forces. A list of 18 required specialty tools is also included.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix PED) Service Repair Manua...9fiisekodkdmd
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and refers to various tools needed to remove parts like housing assemblies, gears, bearings, seals, plates, and clutch groups. Safety notices are included to handle parts and release spring forces carefully. The high-level goal is to disassemble the transmission and torque converter into their individual components to allow for inspection and repair of parts.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like housing assemblies, gears, clutches, seals, bearings and more. Special tools are required and safety precautions mentioned include preventing fluid loss, cleaning parts, and protecting from spring forces. The goal is a fully disassembled transmission for inspection or repair of internal parts.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix PED) Service Repair Manua...9fikslkddmd8u
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and refers to various tools needed to remove parts like housing assemblies, gears, bearings, seals, plates, and clutch groups. Safety notices are included to handle parts and release spring forces carefully. The high-level goal is to disassemble the transmission and torque converter into their individual components to allow for inspection and repair of parts.
This document provides instructions for disassembling the transmission and torque converter of wheel loader models 924H and 924HZ. It outlines 34 steps to fully disassemble the components, including removing housing assemblies, gears, bearings, seals, plates, discs, pistons, springs, and other parts. Precautions are provided regarding fluid containment, cleanliness, and safety when releasing spring forces. A list of 18 required specialty tools is also included.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix PED) Service Repair Manua...9fiisekodkdmd
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and refers to various tools needed to remove parts like housing assemblies, gears, bearings, seals, plates, and clutch groups. Safety notices are included to handle parts and release spring forces carefully. The high-level goal is to disassemble the transmission and torque converter into their individual components to allow for inspection and repair of parts.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like housing assemblies, gears, clutches, seals, bearings and more. Special tools are required and safety precautions mentioned include preventing fluid loss, cleaning parts, and protecting from spring forces. The goal is a fully disassembled transmission for inspection or repair of internal parts.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix PED) Service Repair Manua...9fikslkddmd8u
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and refers to various tools needed to remove parts like housing assemblies, gears, bearings, seals, plates, and clutch groups. Safety notices are included to handle parts and release spring forces carefully. The high-level goal is to disassemble the transmission and torque converter into their individual components to allow for inspection and repair of parts.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix JTM) Service Repair Manua...fijsekkdmdm2w
The document provides disassembly instructions for a transmission and torque converter on a wheel loader model. It lists over 40 steps to disassemble various components using specialized tools, including removing housing assemblies, gears, bearings, seals, plates, discs, pistons, springs, and sensors. Cleanliness is emphasized throughout the process to prevent contamination of parts.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix JTM) Service Repair Manua...onyvzcwadtu05
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It describes 34 steps to disassemble the components, including removing bolts, seals, gears, bearings, plates, discs, pistons, springs, and other parts. Precautions are outlined for releasing spring tension and containing fluids. Required tools include lever pullers, link brackets, jack stands, shackles, forcing screws, retaining ring pliers, slide hammers, compressors, drivers, crossblocks, legs, and puller plates.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix JTM) Service Repair Manua...ze3xiandiao
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It describes 34 steps to disassemble the components, including removing bolts, seals, gears, bearings, plates, discs, pistons, springs, and other parts. Precautions are outlined for releasing spring tension and containing fluids. Required tools include lever pullers, link brackets, jack stands, shackles, forcing screws, retaining ring pliers, slide hammers, compressors, drivers, crossblocks, legs, and puller plates.
This document provides disassembly instructions for a 924HZ wheel loader transmission and torque converter. It outlines 48 steps to fully disassemble the transmission, including removing housing assemblies, gears, shafts, bearings, seals, and clutch groups. Various specialty tools are required to separate components and remove retaining rings. Precautions are listed to prevent fluid loss and contamination during disassembly.
The document provides disassembly instructions for a 924HZ wheel loader transmission and torque converter. It outlines 48 steps to disassemble the transmission housing, remove internal components like gears, shafts, and clutches. Precautions are listed to prevent fluid loss and contamination. Required specialty tools are also identified to aid in disassembly of components like bearings, seals, and springs.
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It outlines 49 steps to fully disassemble the components, including removing housing assemblies, gears, clutches, bearings, seals and other parts. Special tools are required for tasks like removing retaining rings, compressing springs and separating connected pieces. Cleanliness is important during disassembly to prevent contamination of parts.
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It describes in detail how to remove over 30 components using various tools. Key steps include removing the transmission oil pump, then lifting out the transmission and torque converter as a unit. Multiple gears, bearings, seals, and clutch assemblies must then be dismantled using retaining ring pliers and pullers to access all internal parts. Cleanliness is emphasized throughout to prevent contamination.
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It outlines 49 steps to fully disassemble the components, including removing housing assemblies, gears, clutches, bearings, seals and other parts. Special tools are required for tasks like removing retaining rings, compressing springs and separating connected pieces. Cleanliness is important during disassembly to prevent contamination of parts.
This document provides disassembly instructions for the transmission and torque converter of a 928HZ wheel loader model. It outlines 47 steps to fully disassemble these components, including removing housing assemblies, gears, clutches, seals, bearings and other internal parts. Many steps require the use of specialized tools to compress springs, remove retaining rings, separate connected pieces and lift heavy subassemblies weighing over 100 lbs. Cleanliness is emphasized throughout to prevent contamination of parts during disassembly.
This document provides disassembly instructions for the transmission and torque converter of a 928HZ wheel loader model. It outlines 47 steps to fully disassemble these components, including removing housing assemblies, gears, clutches, seals, bearings and other internal parts. Many steps require the use of specialized tools to compress springs, remove retaining rings, separate connected pieces and lift heavy subassemblies weighing over 100 lbs. Cleanliness is emphasized throughout to prevent contamination of parts during disassembly.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader. It describes removing over 30 components in a specific sequence, including removing identification marks, cleaning parts, draining fluids, and using various tools to separate housings, remove seals, bearings, gears, plates, rings, and other parts. Precautions are outlined for releasing spring forces and preventing fluid loss or contamination during disassembly.
This document provides instructions for removing and installing various engine components on a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and rocker arm shaft assembly. The procedures describe disconnecting wiring harnesses, removing nuts and bolts, checking and replacing seals, lubricating parts, and tightening components to the specified torques. Special notes are provided regarding keeping parts clean, marking components for reinstallation, and adjusting valve lash.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, precisely positioning bearings, and torquing bolts to the correct specifications.
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a Caterpillar C11 engine. The removal process involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation process provides steps to install these components in reverse order and includes precautions like applying threadlocker and ensuring proper bearing alignment. Precise dimensions and torque specifications are given for correct installation.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412E and 3408E engines. The cylinder head removal procedure involves detaching hoses, removing the exhaust manifold, fuel manifold, and cylinder head bolts. Special tools are required to safely lift the heavy cylinder head. Reinstallation follows the reverse order. The lifter group removal requires a special tool to hold the lifters while extracting them from the cylinder block bores. New springs must be installed when reassembling the lifter group.
This document provides instructions for removing and installing the camshaft on a Caterpillar 3412C engine. Key steps include:
1. Removing the front housing, lifter group, and flywheel housing.
2. Removing four bolts and a plate from the rear of the camshaft and removing the camshaft gear.
3. Aligning timing marks and removing two bolts and a plate from the camshaft.
4. Removing the camshaft from the cylinder block and optionally removing the camshaft gear using a driver group tool.
This service repair manual provides instructions for removing and installing the flywheel housing and rear power take-off (RPTO) on a Caterpillar 657G wheel tractor. The flywheel housing removal procedure involves removing bolts and seals, then lifting the housing off using lifting brackets. Installation involves cleaning parts, applying sealant, positioning seals and gaskets, and tightening bolts in a specific sequence. The RPTO removal procedure describes removing gears, idlers, retainers, sleeves and covers. Installation involves cleaning, lubricating, and positioning these parts before securing with bolts.
The document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals from the bearing cage.
4. Disassembling the flywheel scavenge pump by removing O-rings, bolts, bearings, and shaft components.
This document provides instructions for installing a crankshaft rear seal on a Caterpillar 657E wheel scraper. It describes cleaning and applying retaining compound to the crankshaft and wear sleeve. A locator is installed on the crankshaft to position the wear sleeve and seal, which are then installed using an installer tool. Finally, the installer is removed and bolts are tightened to complete the installation.
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The disassembly process involves removing 18 components from the transfer gear case including gears, shafts, bearings, and seals. The assembly process describes installing these components in 23 steps, noting proper orientation and torque specifications. Tools required include various pullers, presses, and forcing screws.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hydraulic and electrical connections, draining fluid from the elbow, attaching a lifting device to the pump, and removing mounting nuts and the pump. Cleaning parts and plugging lines is noted for prevent contamination during removal.
More Related Content
Similar to Caterpillar Cat 924HZ Wheel Loader (Prefix WLB) Service Repair Manual Instant Download.pdf
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix JTM) Service Repair Manua...fijsekkdmdm2w
The document provides disassembly instructions for a transmission and torque converter on a wheel loader model. It lists over 40 steps to disassemble various components using specialized tools, including removing housing assemblies, gears, bearings, seals, plates, discs, pistons, springs, and sensors. Cleanliness is emphasized throughout the process to prevent contamination of parts.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix JTM) Service Repair Manua...onyvzcwadtu05
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It describes 34 steps to disassemble the components, including removing bolts, seals, gears, bearings, plates, discs, pistons, springs, and other parts. Precautions are outlined for releasing spring tension and containing fluids. Required tools include lever pullers, link brackets, jack stands, shackles, forcing screws, retaining ring pliers, slide hammers, compressors, drivers, crossblocks, legs, and puller plates.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix JTM) Service Repair Manua...ze3xiandiao
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It describes 34 steps to disassemble the components, including removing bolts, seals, gears, bearings, plates, discs, pistons, springs, and other parts. Precautions are outlined for releasing spring tension and containing fluids. Required tools include lever pullers, link brackets, jack stands, shackles, forcing screws, retaining ring pliers, slide hammers, compressors, drivers, crossblocks, legs, and puller plates.
This document provides disassembly instructions for a 924HZ wheel loader transmission and torque converter. It outlines 48 steps to fully disassemble the transmission, including removing housing assemblies, gears, shafts, bearings, seals, and clutch groups. Various specialty tools are required to separate components and remove retaining rings. Precautions are listed to prevent fluid loss and contamination during disassembly.
The document provides disassembly instructions for a 924HZ wheel loader transmission and torque converter. It outlines 48 steps to disassemble the transmission housing, remove internal components like gears, shafts, and clutches. Precautions are listed to prevent fluid loss and contamination. Required specialty tools are also identified to aid in disassembly of components like bearings, seals, and springs.
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It outlines 49 steps to fully disassemble the components, including removing housing assemblies, gears, clutches, bearings, seals and other parts. Special tools are required for tasks like removing retaining rings, compressing springs and separating connected pieces. Cleanliness is important during disassembly to prevent contamination of parts.
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It describes in detail how to remove over 30 components using various tools. Key steps include removing the transmission oil pump, then lifting out the transmission and torque converter as a unit. Multiple gears, bearings, seals, and clutch assemblies must then be dismantled using retaining ring pliers and pullers to access all internal parts. Cleanliness is emphasized throughout to prevent contamination.
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It outlines 49 steps to fully disassemble the components, including removing housing assemblies, gears, clutches, bearings, seals and other parts. Special tools are required for tasks like removing retaining rings, compressing springs and separating connected pieces. Cleanliness is important during disassembly to prevent contamination of parts.
This document provides disassembly instructions for the transmission and torque converter of a 928HZ wheel loader model. It outlines 47 steps to fully disassemble these components, including removing housing assemblies, gears, clutches, seals, bearings and other internal parts. Many steps require the use of specialized tools to compress springs, remove retaining rings, separate connected pieces and lift heavy subassemblies weighing over 100 lbs. Cleanliness is emphasized throughout to prevent contamination of parts during disassembly.
This document provides disassembly instructions for the transmission and torque converter of a 928HZ wheel loader model. It outlines 47 steps to fully disassemble these components, including removing housing assemblies, gears, clutches, seals, bearings and other internal parts. Many steps require the use of specialized tools to compress springs, remove retaining rings, separate connected pieces and lift heavy subassemblies weighing over 100 lbs. Cleanliness is emphasized throughout to prevent contamination of parts during disassembly.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader. It describes removing over 30 components in a specific sequence, including removing identification marks, cleaning parts, draining fluids, and using various tools to separate housings, remove seals, bearings, gears, plates, rings, and other parts. Precautions are outlined for releasing spring forces and preventing fluid loss or contamination during disassembly.
Similar to Caterpillar Cat 924HZ Wheel Loader (Prefix WLB) Service Repair Manual Instant Download.pdf (11)
This document provides instructions for removing and installing various engine components on a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and rocker arm shaft assembly. The procedures describe disconnecting wiring harnesses, removing nuts and bolts, checking and replacing seals, lubricating parts, and tightening components to the specified torques. Special notes are provided regarding keeping parts clean, marking components for reinstallation, and adjusting valve lash.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck with a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation procedure specifies cleaning and lubricating components, precisely positioning bearings, and torquing bolts to the correct specifications.
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a Caterpillar C11 engine. The removal process involves using various tools to remove bolts, seals, gears, covers, and bearings. The installation process provides steps to install these components in reverse order and includes precautions like applying threadlocker and ensuring proper bearing alignment. Precise dimensions and torque specifications are given for correct installation.
This document provides instructions for disassembling and assembling the torque converter of a 657G Wheel Tractor. It lists the required tools and gives step-by-step instructions with accompanying illustrations. The torque converter is first disassembled by removing various components like the retaining rings, bolts, plates, and internal mechanisms. It is then reassembled in the reverse order, ensuring cleanliness and applying grease as needed.
This service repair manual provides instructions for removing and installing the cylinder head and lifter group on Caterpillar 3412E and 3408E engines. The cylinder head removal procedure involves detaching hoses, removing the exhaust manifold, fuel manifold, and cylinder head bolts. Special tools are required to safely lift the heavy cylinder head. Reinstallation follows the reverse order. The lifter group removal requires a special tool to hold the lifters while extracting them from the cylinder block bores. New springs must be installed when reassembling the lifter group.
This document provides instructions for removing and installing the camshaft on a Caterpillar 3412C engine. Key steps include:
1. Removing the front housing, lifter group, and flywheel housing.
2. Removing four bolts and a plate from the rear of the camshaft and removing the camshaft gear.
3. Aligning timing marks and removing two bolts and a plate from the camshaft.
4. Removing the camshaft from the cylinder block and optionally removing the camshaft gear using a driver group tool.
This service repair manual provides instructions for removing and installing the flywheel housing and rear power take-off (RPTO) on a Caterpillar 657G wheel tractor. The flywheel housing removal procedure involves removing bolts and seals, then lifting the housing off using lifting brackets. Installation involves cleaning parts, applying sealant, positioning seals and gaskets, and tightening bolts in a specific sequence. The RPTO removal procedure describes removing gears, idlers, retainers, sleeves and covers. Installation involves cleaning, lubricating, and positioning these parts before securing with bolts.
The document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals from the bearing cage.
4. Disassembling the flywheel scavenge pump by removing O-rings, bolts, bearings, and shaft components.
This document provides instructions for installing a crankshaft rear seal on a Caterpillar 657E wheel scraper. It describes cleaning and applying retaining compound to the crankshaft and wear sleeve. A locator is installed on the crankshaft to position the wear sleeve and seal, which are then installed using an installer tool. Finally, the installer is removed and bolts are tightened to complete the installation.
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The disassembly process involves removing 18 components from the transfer gear case including gears, shafts, bearings, and seals. The assembly process describes installing these components in 23 steps, noting proper orientation and torque specifications. Tools required include various pullers, presses, and forcing screws.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hydraulic and electrical connections, draining fluid from the elbow, attaching a lifting device to the pump, and removing mounting nuts and the pump. Cleaning parts and plugging lines is noted for prevent contamination during removal.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 657E wheel tractor, including:
- Removing the rear gear group by pressing components out of adapter assemblies, using pullers to remove bearings, and disassembling individual gears.
- Removing the flywheel by using bolting brackets to hold the crankshaft gear, installing guide bolts, and lifting the flywheel off with a hoist.
- Reinstalling components by pressing bearings into place with drives, torquing bolts, and checking runout after installing the flywheel.
The document provides detailed step-by-step instructions accompanied by illustrations of the disassembly and
This document provides instructions for installing and removing the crankshaft rear seal on a Caterpillar 657E wheel scraper. The removal procedure involves using a punch or slide hammer puller to puncture and remove the existing seal. The installation procedure specifies using a seal installer tool and retaining compound to press the new seal and wear sleeve onto the crankshaft. Precautions are given to keep the components clean and not reuse a separated seal and sleeve. The instructions are illustrated with diagrams and apply to both engine configurations with and without a rear gear train.
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar 651E wheel scraper. The removal procedure involves using various tools to disassemble the adapter assemblies, gears, bearings and other components. The installation procedure describes cleaning and lubricating parts, pressing or installing bearings and gears back into place, and reassembling the components in reverse order. Precautions are given to keep parts clean and lubricated to prevent wear.
This document provides instructions for removing and installing a camshaft on a Caterpillar 651E wheel scraper model. It describes the required tools and multi-step processes for both removing the camshaft from the front or rear of the engine and installing a new camshaft. Precautions are outlined to prevent damage and contain fluids. The document is intended as a service repair manual for technicians performing camshaft maintenance on this model.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 24 individual parts in 24 steps, including the housing assembly, torque converter assembly, impeller wheel assembly, carrier assembly, and stator assembly. It then describes assembling the torque converter in 25 steps by installing the parts in reverse order. Tools required include link brackets, a transmission repair stand, drivers, pullers, and slide hammers.
Caterpillar Cat 651 and 651B WHEEL SCRAPER (Prefix 45M) Service Repair Manual...9fikslkddmd8u
The document provides instructions for disassembling and assembling various components of a 651B Wheel Scraper transmission and transfer gear, including:
- Removing the transmission transfer gear, governor drive shaft, clutches, valve groups, manifolds, and oil filter base.
- Disassembling the transmission transfer gear, governor, and individual valve bodies.
- Assembling the transmission transfer gear, governor, and individual valve bodies.
- Removing and installing the entire transmission, including draining fluid and disconnecting/reconnecting lines and linkages.
Caterpillar Cat 650B and 660B WHEEL TRACTOR (Prefix 58K) Service Repair Manua...9fikslkddmd8u
This document provides instructions for removing the camshaft from Caterpillar 650B and 660B wheel tractors. It involves removing components like the camshaft gear and rocker arms first. Tools like a cradle, guide, camshaft pilots and hooks are then used to support the camshaft as it is moved out of the cylinder head and into the guide. Care must be taken to avoid damaging the camshaft or bearings during removal.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes removing 18 components of the torque converter in sequential order, including the retaining ring, impeller, carrier assembly, stator, and turbine. It also describes assembling the torque converter components in reverse order, noting to keep parts clean and apply Loctite to the threaded rod.
The document provides instructions for disassembling and assembling the transmission, differential, transfer gear, and retarder of a Caterpillar 641 wheel scraper. It details removing and installing various components such as gears, bearings, shafts, pumps, and housings. Detailed steps are provided for tasks like draining fluids, loosening bolts, using hoists and tools, adjusting clearances, and torquing fasteners.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 924HZ WHEEL LOADER WLB
Configuration: 924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
924H, 924HZ, 928HZ and 930H Wheel Loaders Power Train
Media Number -KENR7606-09 Publication Date -01/03/2015 Date Updated -09/10/2017
i07376985
Transmission and Torque Converter - Disassemble
SMCS - 3001-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-9200 Lever Puller Hoist 1
138-7575 Link Bracket 3
B
8T-0372
Bolt
M12 - 1.75 by 90mm
3
180-3033 Jack Stand Gp 2
180-3032 Jack Stand Gp 1
189-0410 Shackle As 2
C 8T-0644
Bolt
M10 - 1.5 by 90mm
2
D
1U-9200 Lever Puller Hoist 1
138-7575 Link Bracket 4
189-0409 Shackle As 1
E 154-6181 Forcing Screw 2
F 136-1452 Retaining Ring Pliers As 1
G 1P-0074 Slide Hammer Puller Gp 1
4C-5653 Threaded Adapter 1
1/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. H 1P-1863 Retaining Ring Pliers 1
J 4C-6136 Lifting Bracket 1
K 1P-1861 Retaining Ring Pliers 1
L 1P-0510 Driver Gp 1
M 4C-3652 Compressor Assembly 1
N 1P-1857 Retaining Ring Pliers 1
P
1P-2322 Combination Puller 1
1P-0510 Driver Gp 1
Q
1U-9889 Crossblock 1
3H-0469 Leg 2
3H-0468 Puller Plate 4
1A-1935 Full Nut 2
1U-7540 Hydraulic Cylinder 1
1U-5230 Hand Hydraulic Pump 1
1H-3110 Bearing Puller Gp 1
R 4C-6399 Compressor Assembly 1
Start By:
a. Remove the transmission oil pump. Refer to Disassembly and Assembly, "Transmission Oil
Pump - Remove".
b. Remove the transmission and the torque converter. Refer to Disassembly and Assembly,
"Transmission and Torque Converter - Remove".
Note: Put identification marks on all hoses, on all hose assemblies, on all harness assemblies, and
on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies.
This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
2/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01392601
1. Attach Tooling (A) and a suitable lifting device to the transmission and the torque
converter. The weight of the transmission and torque converter is approximately 476 kg
(1050 lb).
Illustration 2 g01392602
2. Remove bolts (1) and sight gauge (2).
3/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 3 g01392621
3. Position the transmission and the torque converter onto Tooling (B), as shown.
Illustration 4 g01392620
4. Remove bolts (3) and coupling (4).
Illustration 5 g01392597
5. Remove torque converter (5).
4/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 6 g01392622
Illustration 7 g01392630
6. Remove bolts (6). Use Tooling (C) and suitable prybars to remove plate (7).
Illustration 8 g01392632
7. Remove O-ring seal (8) from plate (7).
5/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 9 g01392635
8. Remove O-ring seals (9).
Illustration 10 g01392639
9. Remove hose assembly (10). Disconnect the lower half harness assembly (12) and secure
the harness assembly to control valve (11).
6/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 11 g01393407
10. Attach Tooling (D) and a suitable lifting device to housing assembly (13). The weight of
housing assembly (13) is approximately 141 kg (310 lb).
Illustration 12 g01393411
11. Use Tooling (E) to separate the housings. Remove housing assembly (13).
7/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 16 g01395864
14. Use Tooling (F) to remove retaining ring (19).
Illustration 17 g01396011
15. Use Tooling (G) in a rotating pattern to remove bearing assembly (20).
Illustration 18 g01396014
9/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 16. Use Tooling (H) to remove retaining ring (23). Remove bearing support (21). Remove
bearing (22) from bearing support (21).
Illustration 19 g01396015
17. Remove bearing cup (24) and bearings (25).
Illustration 20 g01396258
18. Remove sensors (28).
19. Use Tooling (J) and a suitable lifting device to remove the forward low and the forward
high clutch group (26). The weight of clutch group (26) is approximately 27 kg (60 lb).
Position shaft assembly (27) out of the way and remove clutch group (26).
Note: When the clutch groups are disassembled, remove the plugs in the shaft to clean the
oil passages. Use a punch to drive the plug into the shaft . Drill the remainder of the
aluminum plug out of the bore. Be careful not to drill any portion of the walls of the bore.
Use shop air or a cleaning solution to clean the shafts.
10/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 21 g01397406
20. Remove retaining ring (29) and thrust disc (30).
Illustration 22 g01397412
21. Remove gear assembly (31).
Illustration 23 g01396271
22. Use Tooling (H) to remove retaining ring (33). Use Tooling (L) to remove hub (32) from
gear assembly (31).
11/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 24 g01396539
23. Use Tooling (K) to remove retaining ring (34). Use Tooling (L) to remove bearing (35)
from hub (32).
Illustration 25 g01396540
24. Remove thrust disc (36).
12/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 26 g01397401
25. Remove retaining ring (37) and plate (38). Remove discs (39) and plates (40).
Note: Note the location of plates and discs for assembly purposes.
Illustration 27 g01397484
13/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
26. Install Tooling (M) onto retainer (42). Use Tooling (M) and a suitable press to compress the
clutch spring. Remove retaining ring (41). Slowly release the spring tension.
Illustration 28 g01397502
27. Remove retainer (42) and spring (43).
28. Remove piston (44).
14/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
30. If equipped, remove valve assembly (53). Remove seal (48), retaining ring (47), retainer
(49), spring (50), and ball (51) from body (52).
31. Remove rings (46).
Illustration 31 g01397884
32. Reposition clutch group (26), as shown. Remove retaining ring (54), thrust disc (55), and
hub (56).
Illustration 32 g01397964
33. Use Tooling (K) to remove retaining ring (57) from hub (56). Remove bearing (58).
16/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 33 g01397953
34. Remove thrust disc (59).
35. Repeat Steps 25 through 30 to disassemble the clutch pack.
Illustration 34 g01397984
36. Attach Tooling (J) and a suitable lifting device to the reverse and second clutch group (60).
The weight of clutch group (60) is approximately 32 kg (70 lb). Position clutch group (60)
onto suitable blocking.
Illustration 35 g01397987
17/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. 37. Remove retaining ring (61), thrust disc (62), and gear (63).
Illustration 36 g01398268
38. Use Tooling (H) to remove retaining ring (65). Use Tooling (L) to remove hub (64) from
gear (63).
Illustration 37 g01398270
39. Use Tooling (K) to remove retaining ring (66). Use Tooling (L) to remove bearing (67)
from hub (64).
18/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 38 g01398284
40. Remove thrust disc (68).
41. Repeat Steps 25 through 30 for the disassembly of the clutch pack.
Illustration 39 g01398178
42. Use Tooling (P) to remove bearing (69).
19/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. 44. Remove gear (75).
Illustration 42 g01398437
45. Use Tooling (H) to remove retaining ring (77). Use Tooling (L) to remove hub (76) from
gear (75).
Illustration 43 g01398456
46. Use Tooling (K) to remove retaining ring (78). Use Tooling (L) to remove bearing (79)
from hub (76).
21/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 44 g01398438
47. Remove thrust disc (80).
48. Repeat Steps 25 through 30 for the disassembly of the clutch pack.
Illustration 45 g01398560
49. Attach Tooling (J) and a suitable lifting device to first gear and third gear clutch group (81).
The weight of clutch group (81) is approximately 45 kg (100 lb). Remove clutch group (81).
Illustration 46 g01398561
50. Remove retaining ring (82), thrust disc (83), and gear (84).
22/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 47 g01398645
51. Use Tooling (H) to remove retaining ring (86). Use Tooling (L) to remove hub (85) from
gear (84).
Illustration 48 g01398657
52. Use Tooling (K) to remove retaining ring (87). Use Tooling (L) to remove bearing (88)
from hub (85).
23/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 49 g01398664
53. Remove thrust disc (89).
54. Repeat Steps 25 through 30 for the disassembly of the clutch pack.
Illustration 50 g01398562
Illustration 51 g01398564
55. Install Tooling (Q), as shown. Use Tooling (Q) to remove bearing (90). Extend the cylinder
several times to remove bearing (90). Use spacers, as needed.
24/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 52 g01398565
56. Remove spacer (91) and gear (92).
Illustration 53 g01398567
57. Remove thrust disc (93) and gear (94).
Illustration 54 g01398773
58. Use Tooling (H) to remove retaining ring (95). Remove hub (96) from gear (94). Use
Tooling (L) to remove bearing (97).
Illustration 55 g01398774
25/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. 59. Remove thrust disc (98) and washer (99).
Illustration 56 g01398776
60. Remove retaining ring (100) and plate (101).
61. Remove clutch plates and discs (103).
Note: Note the positions of the plates and discs for assembly purposes.
62. Remove retaining ring (102).
Illustration 57 g01398814
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
26/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. 63. Position Tooling (R) onto seal assembly (105). Use Tooling (R) and a suitable press to
compress the clutch spring. Remove retaining ring (104). Slowly release the spring tension.
Illustration 58 g01398781
64. Remove ring (106) and seal assembly (105).
Illustration 59 g01398796
65. Remove spring (107) and piston (108).
Illustration 60 g01398985
66. Remove seals (109).
27/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 61 g01398975
67. Remove input shaft assembly (110).
Illustration 62 g01399007
68. Use a suitable press to remove carrier (111) and bearing cone (113). Remove ring seal (112)
from carrier (111). Remove gear (114).
69. Use a suitable press to remove bearing cone (116). Remove gear (115).
28/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
31. 72. Remove bolt (123) and washer (124).
Illustration 66 g01399321
73. Remove seal (125). Remove yoke (126) and brake drum (127) together.
Illustration 67 g01399325
74. Remove bolts (128). Remove plate (129).
75. Remove parking brake assembly (130) and lever (131).
Illustration 68 g01399332
30/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
32. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
33. 76. Remove bolts (132).
Illustration 69 g06299489
77. Use two of bolts (132) as forcing bolts to remove cage (133). Remove shims (134).
Illustration 70 g01399379
78. Remove seal (135). Remove bearing cup (136) and lip seal (137).
Illustration 71 g01399397
79. Remove the output shaft and gear (140).
31/33
924HZ Wheel Loader WLB00001-UP (MACHINE) POWERED BY C6.6 Engine(S...
2021/1/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...