This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It outlines 49 steps to fully disassemble the components, including removing housing assemblies, gears, clutches, bearings, seals and other parts. Special tools are required for tasks like removing retaining rings, compressing springs and separating connected pieces. Cleanliness is important during disassembly to prevent contamination of parts.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix JTM) Service Repair Manua...fijsekkdmdm2w
The document provides disassembly instructions for a transmission and torque converter on a wheel loader model. It lists over 40 steps to disassemble various components using specialized tools, including removing housing assemblies, gears, bearings, seals, plates, discs, pistons, springs, and sensors. Cleanliness is emphasized throughout the process to prevent contamination of parts.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix JTM) Service Repair Manua...onyvzcwadtu05
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It describes 34 steps to disassemble the components, including removing bolts, seals, gears, bearings, plates, discs, pistons, springs, and other parts. Precautions are outlined for releasing spring tension and containing fluids. Required tools include lever pullers, link brackets, jack stands, shackles, forcing screws, retaining ring pliers, slide hammers, compressors, drivers, crossblocks, legs, and puller plates.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix JTM) Service Repair Manua...ze3xiandiao
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It describes 34 steps to disassemble the components, including removing bolts, seals, gears, bearings, plates, discs, pistons, springs, and other parts. Precautions are outlined for releasing spring tension and containing fluids. Required tools include lever pullers, link brackets, jack stands, shackles, forcing screws, retaining ring pliers, slide hammers, compressors, drivers, crossblocks, legs, and puller plates.
This document provides instructions for disassembling the transmission and torque converter of wheel loader models 924H and 924HZ. It outlines 34 steps to fully disassemble the components, including removing housing assemblies, gears, bearings, seals, plates, discs, pistons, springs, and other parts. Precautions are provided regarding fluid containment, cleanliness, and safety when releasing spring forces. A list of 18 required specialty tools is also included.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix PED) Service Repair Manua...9fiisekodkdmd
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and refers to various tools needed to remove parts like housing assemblies, gears, bearings, seals, plates, and clutch groups. Safety notices are included to handle parts and release spring forces carefully. The high-level goal is to disassemble the transmission and torque converter into their individual components to allow for inspection and repair of parts.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix JTM) Service Repair Manua...fijsekkdmdm2w
The document provides disassembly instructions for a transmission and torque converter on a wheel loader model. It lists over 40 steps to disassemble various components using specialized tools, including removing housing assemblies, gears, bearings, seals, plates, discs, pistons, springs, and sensors. Cleanliness is emphasized throughout the process to prevent contamination of parts.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix JTM) Service Repair Manua...onyvzcwadtu05
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It describes 34 steps to disassemble the components, including removing bolts, seals, gears, bearings, plates, discs, pistons, springs, and other parts. Precautions are outlined for releasing spring tension and containing fluids. Required tools include lever pullers, link brackets, jack stands, shackles, forcing screws, retaining ring pliers, slide hammers, compressors, drivers, crossblocks, legs, and puller plates.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix JTM) Service Repair Manua...ze3xiandiao
This document provides disassembly instructions for a 924H wheel loader transmission and torque converter. It describes 34 steps to disassemble the components, including removing bolts, seals, gears, bearings, plates, discs, pistons, springs, and other parts. Precautions are outlined for releasing spring tension and containing fluids. Required tools include lever pullers, link brackets, jack stands, shackles, forcing screws, retaining ring pliers, slide hammers, compressors, drivers, crossblocks, legs, and puller plates.
This document provides instructions for disassembling the transmission and torque converter of wheel loader models 924H and 924HZ. It outlines 34 steps to fully disassemble the components, including removing housing assemblies, gears, bearings, seals, plates, discs, pistons, springs, and other parts. Precautions are provided regarding fluid containment, cleanliness, and safety when releasing spring forces. A list of 18 required specialty tools is also included.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix PED) Service Repair Manua...9fiisekodkdmd
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and refers to various tools needed to remove parts like housing assemblies, gears, bearings, seals, plates, and clutch groups. Safety notices are included to handle parts and release spring forces carefully. The high-level goal is to disassemble the transmission and torque converter into their individual components to allow for inspection and repair of parts.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like housing assemblies, gears, clutches, seals, bearings and more. Special tools are required and safety precautions mentioned include preventing fluid loss, cleaning parts, and protecting from spring forces. The goal is a fully disassembled transmission for inspection or repair of internal parts.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix PED) Service Repair Manua...9fikslkddmd8u
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and refers to various tools needed to remove parts like housing assemblies, gears, bearings, seals, plates, and clutch groups. Safety notices are included to handle parts and release spring forces carefully. The high-level goal is to disassemble the transmission and torque converter into their individual components to allow for inspection and repair of parts.
This document provides disassembly instructions for the transmission and torque converter of a 928HZ wheel loader model. It outlines 47 steps to fully disassemble these components, including removing housing assemblies, gears, clutches, seals, bearings and other internal parts. Many steps require the use of specialized tools to compress springs, remove retaining rings, separate connected pieces and lift heavy subassemblies weighing over 100 lbs. Cleanliness is emphasized throughout to prevent contamination of parts during disassembly.
This document provides disassembly instructions for the transmission and torque converter of a 928HZ wheel loader model. It outlines 47 steps to fully disassemble these components, including removing housing assemblies, gears, clutches, seals, bearings and other internal parts. Many steps require the use of specialized tools to compress springs, remove retaining rings, separate connected pieces and lift heavy subassemblies weighing over 100 lbs. Cleanliness is emphasized throughout to prevent contamination of parts during disassembly.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader. It describes removing over 30 components in a specific sequence, including removing identification marks, cleaning parts, draining fluids, and using various tools to separate housings, remove seals, bearings, gears, plates, rings, and other parts. Precautions are outlined for releasing spring forces and preventing fluid loss or contamination during disassembly.
This document provides instructions for disassembling the transmission and torque converter of a 924HZ wheel loader. It outlines 48 steps to remove various components such as housing assemblies, gears, clutches, seals, bearings and other parts. Precautions are listed to prevent fluid loss and entry of contaminants. Required tools include lever pullers, jack stands, retaining ring pliers, drivers, compressors and other specialized equipment to separate components and remove securing components.
This document provides instructions for disassembling the transmission and torque converter of a 924HZ wheel loader. It outlines 48 steps to remove various components such as housing assemblies, gears, clutches, seals, bearings and other parts. Precautions are listed to prevent fluid loss and entry of contaminants. Required tools include lever pullers, jack stands, retaining ring pliers, drivers, compressors and other specialized equipment to separate components in a clean and safe manner.
This document provides disassembly instructions for a 924HZ wheel loader transmission and torque converter. It outlines 48 steps to fully disassemble the transmission, including removing housing assemblies, gears, shafts, bearings, seals, and clutch groups. Various specialty tools are required to separate components and remove retaining rings. Precautions are listed to prevent fluid loss and contamination during disassembly.
The document provides disassembly instructions for a 924HZ wheel loader transmission and torque converter. It outlines 48 steps to disassemble the transmission housing, remove internal components like gears, shafts, and clutches. Precautions are listed to prevent fluid loss and contamination. Required specialty tools are also identified to aid in disassembly of components like bearings, seals, and springs.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix RTA) Service Repair Manua...9fikslkddmd8u
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists 50 steps to completely disassemble the transmission, removing components like gears, plates, seals, bearings, and clutch groups. Special tools are required for tasks like compressing clutch springs and removing certain parts. Cleanliness is emphasized throughout to prevent dirt from contaminating internal parts.
This document provides disassembly instructions for a transmission and torque converter for wheel loader models 924G and 924Gz. It lists the required tools and presents a step-by-step process to disassemble the transmission, torque converter, and various clutch groups within the transmission. The disassembly involves removing bolts, seals, gears, plates, discs, bearings, springs, and other internal components. Cleanliness during disassembly is emphasized.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix DDA) Service Repair Manua...9fiisekodkdmd
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and presents a step-by-step process with illustrations. Some key steps include removing the torque converter, various clutch groups, gears, seals, bearings, and other internal components. Cleanliness is emphasized throughout the disassembly process to prevent dirt from entering the transmission.
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix PJW) Service Repa...fijsekkdmdm2w
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, applying anti-seize compound, installing various seals and gears, and adjusting bearing preload using shims. Precision is required to prevent damage to seals and ensure proper engagement of gears. Lifting devices and care are needed due to components weighing up to 127 kg.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336E and 336E L Excavator (Prefix KED) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for assembling a travel motor on an excavator. It describes 27 steps to assemble internal components like seals, springs, and bearings. These components include pistons, a cam plate, and a rotating assembly. The final steps connect the travel motor to the final drive and install exterior covers. Proper assembly requires using the correct tools and lubricants, and ensuring parts are aligned and torques are set correctly.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to disassemble the pump by removing components like bolts, sensors, valves, springs, pistons, gears, and bearings. The assembly section lists 48 steps to reinstall these components in reverse order, noting the need to heat some bearings before installation and ensure proper placement of pins, seals, and other parts. Precautions are provided for releasing spring forces. Required tools include various pliers, pins, and links to aid in removal and installation of components.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling a 330F excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, brake piston, rotating assembly, pistons, seals, and other parts. Tools required include retaining ring pliers, a bearing puller, bolts, threaded rods, and other hardware. Safety precautions are provided to release spring forces carefully.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336D2L excavator. It describes 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, springs, seals, relief valves, plugs, and more. Precautions are provided to watch for spring forces and contain fluids. Tools needed include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Reassembly will follow the disassembly steps in reverse order.
More Related Content
Similar to Caterpillar Cat 924H Wheel Loader (Prefix HXC) Service Repair Manual Instant Download.pdf
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like housing assemblies, gears, clutches, seals, bearings and more. Special tools are required and safety precautions mentioned include preventing fluid loss, cleaning parts, and protecting from spring forces. The goal is a fully disassembled transmission for inspection or repair of internal parts.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and accompanying illustrations to remove components like gears, clutches, seals, bearings, and housings. Special tools are required for tasks like compressing springs and removing press-fit parts. Cleanliness and fluid containment are emphasized throughout the process.
Caterpillar Cat 924H and 924Hz Wheel Loader (Prefix PED) Service Repair Manua...9fikslkddmd8u
This document provides instructions for disassembling the transmission and torque converter of a wheel loader model. It lists over 40 detailed steps and refers to various tools needed to remove parts like housing assemblies, gears, bearings, seals, plates, and clutch groups. Safety notices are included to handle parts and release spring forces carefully. The high-level goal is to disassemble the transmission and torque converter into their individual components to allow for inspection and repair of parts.
This document provides disassembly instructions for the transmission and torque converter of a 928HZ wheel loader model. It outlines 47 steps to fully disassemble these components, including removing housing assemblies, gears, clutches, seals, bearings and other internal parts. Many steps require the use of specialized tools to compress springs, remove retaining rings, separate connected pieces and lift heavy subassemblies weighing over 100 lbs. Cleanliness is emphasized throughout to prevent contamination of parts during disassembly.
This document provides disassembly instructions for the transmission and torque converter of a 928HZ wheel loader model. It outlines 47 steps to fully disassemble these components, including removing housing assemblies, gears, clutches, seals, bearings and other internal parts. Many steps require the use of specialized tools to compress springs, remove retaining rings, separate connected pieces and lift heavy subassemblies weighing over 100 lbs. Cleanliness is emphasized throughout to prevent contamination of parts during disassembly.
This document provides instructions for disassembling the transmission and torque converter of a wheel loader. It describes removing over 30 components in a specific sequence, including removing identification marks, cleaning parts, draining fluids, and using various tools to separate housings, remove seals, bearings, gears, plates, rings, and other parts. Precautions are outlined for releasing spring forces and preventing fluid loss or contamination during disassembly.
This document provides instructions for disassembling the transmission and torque converter of a 924HZ wheel loader. It outlines 48 steps to remove various components such as housing assemblies, gears, clutches, seals, bearings and other parts. Precautions are listed to prevent fluid loss and entry of contaminants. Required tools include lever pullers, jack stands, retaining ring pliers, drivers, compressors and other specialized equipment to separate components and remove securing components.
This document provides instructions for disassembling the transmission and torque converter of a 924HZ wheel loader. It outlines 48 steps to remove various components such as housing assemblies, gears, clutches, seals, bearings and other parts. Precautions are listed to prevent fluid loss and entry of contaminants. Required tools include lever pullers, jack stands, retaining ring pliers, drivers, compressors and other specialized equipment to separate components in a clean and safe manner.
This document provides disassembly instructions for a 924HZ wheel loader transmission and torque converter. It outlines 48 steps to fully disassemble the transmission, including removing housing assemblies, gears, shafts, bearings, seals, and clutch groups. Various specialty tools are required to separate components and remove retaining rings. Precautions are listed to prevent fluid loss and contamination during disassembly.
The document provides disassembly instructions for a 924HZ wheel loader transmission and torque converter. It outlines 48 steps to disassemble the transmission housing, remove internal components like gears, shafts, and clutches. Precautions are listed to prevent fluid loss and contamination. Required specialty tools are also identified to aid in disassembly of components like bearings, seals, and springs.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix RTA) Service Repair Manua...9fikslkddmd8u
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists 50 steps to completely disassemble the transmission, removing components like gears, plates, seals, bearings, and clutch groups. Special tools are required for tasks like compressing clutch springs and removing certain parts. Cleanliness is emphasized throughout to prevent dirt from contaminating internal parts.
This document provides disassembly instructions for a transmission and torque converter for wheel loader models 924G and 924Gz. It lists the required tools and presents a step-by-step process to disassemble the transmission, torque converter, and various clutch groups within the transmission. The disassembly involves removing bolts, seals, gears, plates, discs, bearings, springs, and other internal components. Cleanliness during disassembly is emphasized.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix DDA) Service Repair Manua...9fiisekodkdmd
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and presents a step-by-step process with illustrations. Some key steps include removing the torque converter, various clutch groups, gears, seals, bearings, and other internal components. Cleanliness is emphasized throughout the disassembly process to prevent dirt from entering the transmission.
Similar to Caterpillar Cat 924H Wheel Loader (Prefix HXC) Service Repair Manual Instant Download.pdf (13)
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix PJW) Service Repa...fijsekkdmdm2w
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, applying anti-seize compound, installing various seals and gears, and adjusting bearing preload using shims. Precision is required to prevent damage to seals and ensure proper engagement of gears. Lifting devices and care are needed due to components weighing up to 127 kg.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336E and 336E L Excavator (Prefix KED) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for assembling a travel motor on an excavator. It describes 27 steps to assemble internal components like seals, springs, and bearings. These components include pistons, a cam plate, and a rotating assembly. The final steps connect the travel motor to the final drive and install exterior covers. Proper assembly requires using the correct tools and lubricants, and ensuring parts are aligned and torques are set correctly.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to disassemble the pump by removing components like bolts, sensors, valves, springs, pistons, gears, and bearings. The assembly section lists 48 steps to reinstall these components in reverse order, noting the need to heat some bearings before installation and ensure proper placement of pins, seals, and other parts. Precautions are provided for releasing spring forces. Required tools include various pliers, pins, and links to aid in removal and installation of components.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling a 330F excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, brake piston, rotating assembly, pistons, seals, and other parts. Tools required include retaining ring pliers, a bearing puller, bolts, threaded rods, and other hardware. Safety precautions are provided to release spring forces carefully.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336D2L excavator. It describes 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, springs, seals, relief valves, plugs, and more. Precautions are provided to watch for spring forces and contain fluids. Tools needed include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Reassembly will follow the disassembly steps in reverse order.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It lists the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, applying seals and retaining compound, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or excess oil consumption.
Caterpillar Cat 926 and 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing the cylinder head assembly on a 3204 vehicular engine. It describes:
1) Removing the cylinder head assembly by loosening hoses, removing bolts, and lifting it off with a hoist.
2) Cleaning and installing a new gasket before lowering the cylinder head back onto the cylinder block and tightening bolts in a specific sequence and torque.
3) Checking the flatness of the cylinder head and block surfaces during installation.
This document provides instructions for disassembling and assembling the torque converter and transmission of a Caterpillar 938F wheel loader. It details removing over 40 individual parts in 21 steps to disassemble the torque converter. A further 44 steps describe disassembling the transmission by removing components like shafts, gears, seals, and clutches. Precise tools and lifting devices are specified to carefully remove heavy parts. Reassembly is outlined in reverse order with notes to check components for wear and replace as needed.
Caterpillar Cat 325C and 325C L Excavator (Prefix BKW) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs to clean all parts thoroughly, apply lubricants, and install the parts in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Tools required include a transmission repair stand, link brackets, retaining ring pliers, and other specialized tools.
This document provides instructions for disassembling and assembling the piston pump of a 623G wheel scraper. Some key steps include:
1. Marking all mating components for alignment during assembly.
2. Removing various seals, springs, spools, and other internal parts from the pump housing and head.
3. Checking the preload on bearings during assembly by measuring clearance between the pump head and housing.
4. Cleaning all parts thoroughly before assembly and applying a light oil film. Precise alignment of marked components is important.
This document provides instructions for disassembling and assembling axle shaft assemblies for a 938F wheel loader. It describes removing components like the axle housing groups, axle shaft assembly, planetary carrier assembly, and installing new components in reverse order. Key steps include using various tools to remove retaining rings, planetary gears, and installing new bearings and seals at specified temperatures while ensuring proper torque specifications are met.
The document provides instructions for removing and installing fuel injection pumps on a Caterpillar 3406C diesel engine. Key steps include using various tools to hold components in place, loosening and removing bushings, seals and pumps. Reinstallation involves aligning pins and slots, installing spacers and seals correctly, and checking rack travel measurements to ensure proper installation. The document also describes disassembling and assembling the fuel injection pumps and fuel injection pump housing.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions describe taking identifying marks on parts and cleaning components to prevent contamination. Reassembly is done in reverse order.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
1. Product: WHEEL LOADER
Model: 924H WHEEL LOADER HXC
Configuration: 924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine
Disassembly and Assembly
924H, 924HZ, 928HZ and 930H Wheel Loaders Power Train
Media Number -KENR7606-09 Publication Date -01/03/2015 Date Updated -09/10/2017
i07376985
Transmission and Torque Converter - Disassemble
SMCS - 3001-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-9200 Lever Puller Hoist 1
138-7575 Link Bracket 3
B
8T-0372
Bolt
M12 - 1.75 by 90mm
3
180-3033 Jack Stand Gp 2
180-3032 Jack Stand Gp 1
189-0410 Shackle As 2
C 8T-0644
Bolt
M10 - 1.5 by 90mm
2
D
1U-9200 Lever Puller Hoist 1
138-7575 Link Bracket 4
189-0409 Shackle As 1
E 154-6181 Forcing Screw 2
F 136-1452 Retaining Ring Pliers As 1
G 1P-0074 Slide Hammer Puller Gp 1
4C-5653 Threaded Adapter 1
1/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. H 1P-1863 Retaining Ring Pliers 1
J 4C-6136 Lifting Bracket 1
K 1P-1861 Retaining Ring Pliers 1
L 1P-0510 Driver Gp 1
M 4C-3652 Compressor Assembly 1
N 1P-1857 Retaining Ring Pliers 1
P
1P-2322 Combination Puller 1
1P-0510 Driver Gp 1
Q
1U-9889 Crossblock 1
3H-0469 Leg 2
3H-0468 Puller Plate 4
1A-1935 Full Nut 2
1U-7540 Hydraulic Cylinder 1
1U-5230 Hand Hydraulic Pump 1
1H-3110 Bearing Puller Gp 1
R 4C-6399 Compressor Assembly 1
Start By:
a. Remove the transmission oil pump. Refer to Disassembly and Assembly, "Transmission Oil
Pump - Remove".
b. Remove the transmission and the torque converter. Refer to Disassembly and Assembly,
"Transmission and Torque Converter - Remove".
Note: Put identification marks on all hoses, on all hose assemblies, on all harness assemblies, and
on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies.
This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
2/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01392601
1. Attach Tooling (A) and a suitable lifting device to the transmission and the torque
converter. The weight of the transmission and torque converter is approximately 476 kg
(1050 lb).
Illustration 2 g01392602
2. Remove bolts (1) and sight gauge (2).
3/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01392621
3. Position the transmission and the torque converter onto Tooling (B), as shown.
Illustration 4 g01392620
4. Remove bolts (3) and coupling (4).
Illustration 5 g01392597
5. Remove torque converter (5).
4/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g01392622
Illustration 7 g01392630
6. Remove bolts (6). Use Tooling (C) and suitable prybars to remove plate (7).
Illustration 8 g01392632
7. Remove O-ring seal (8) from plate (7).
5/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g01392635
8. Remove O-ring seals (9).
Illustration 10 g01392639
9. Remove hose assembly (10). Disconnect the lower half harness assembly (12) and secure
the harness assembly to control valve (11).
6/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g01393407
10. Attach Tooling (D) and a suitable lifting device to housing assembly (13). The weight of
housing assembly (13) is approximately 141 kg (310 lb).
Illustration 12 g01393411
11. Use Tooling (E) to separate the housings. Remove housing assembly (13).
7/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g01395864
14. Use Tooling (F) to remove retaining ring (19).
Illustration 17 g01396011
15. Use Tooling (G) in a rotating pattern to remove bearing assembly (20).
Illustration 18 g01396014
9/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(SE...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 16. Use Tooling (H) to remove retaining ring (23). Remove bearing support (21). Remove
bearing (22) from bearing support (21).
Illustration 19 g01396015
17. Remove bearing cup (24) and bearings (25).
Illustration 20 g01396258
18. Remove sensors (28).
19. Use Tooling (J) and a suitable lifting device to remove the forward low and the forward
high clutch group (26). The weight of clutch group (26) is approximately 27 kg (60 lb).
Position shaft assembly (27) out of the way and remove clutch group (26).
Note: When the clutch groups are disassembled, remove the plugs in the shaft to clean the
oil passages. Use a punch to drive the plug into the shaft . Drill the remainder of the
aluminum plug out of the bore. Be careful not to drill any portion of the walls of the bore.
Use shop air or a cleaning solution to clean the shafts.
10/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g01397406
20. Remove retaining ring (29) and thrust disc (30).
Illustration 22 g01397412
21. Remove gear assembly (31).
Illustration 23 g01396271
22. Use Tooling (H) to remove retaining ring (33). Use Tooling (L) to remove hub (32) from
gear assembly (31).
11/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 24 g01396539
23. Use Tooling (K) to remove retaining ring (34). Use Tooling (L) to remove bearing (35)
from hub (32).
Illustration 25 g01396540
24. Remove thrust disc (36).
12/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g01397401
25. Remove retaining ring (37) and plate (38). Remove discs (39) and plates (40).
Note: Note the location of plates and discs for assembly purposes.
Illustration 27 g01397484
13/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
26. Install Tooling (M) onto retainer (42). Use Tooling (M) and a suitable press to compress the
clutch spring. Remove retaining ring (41). Slowly release the spring tension.
Illustration 28 g01397502
27. Remove retainer (42) and spring (43).
28. Remove piston (44).
14/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
30. If equipped, remove valve assembly (53). Remove seal (48), retaining ring (47), retainer
(49), spring (50), and ball (51) from body (52).
31. Remove rings (46).
Illustration 31 g01397884
32. Reposition clutch group (26), as shown. Remove retaining ring (54), thrust disc (55), and
hub (56).
Illustration 32 g01397964
33. Use Tooling (K) to remove retaining ring (57) from hub (56). Remove bearing (58).
16/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 33 g01397953
34. Remove thrust disc (59).
35. Repeat Steps 25 through 30 to disassemble the clutch pack.
Illustration 34 g01397984
36. Attach Tooling (J) and a suitable lifting device to the reverse and second clutch group (60).
The weight of clutch group (60) is approximately 32 kg (70 lb). Position clutch group (60)
onto suitable blocking.
Illustration 35 g01397987
17/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 37. Remove retaining ring (61), thrust disc (62), and gear (63).
Illustration 36 g01398268
38. Use Tooling (H) to remove retaining ring (65). Use Tooling (L) to remove hub (64) from
gear (63).
Illustration 37 g01398270
39. Use Tooling (K) to remove retaining ring (66). Use Tooling (L) to remove bearing (67)
from hub (64).
18/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 38 g01398284
40. Remove thrust disc (68).
41. Repeat Steps 25 through 30 for the disassembly of the clutch pack.
Illustration 39 g01398178
42. Use Tooling (P) to remove bearing (69).
19/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 44. Remove gear (75).
Illustration 42 g01398437
45. Use Tooling (H) to remove retaining ring (77). Use Tooling (L) to remove hub (76) from
gear (75).
Illustration 43 g01398456
46. Use Tooling (K) to remove retaining ring (78). Use Tooling (L) to remove bearing (79)
from hub (76).
21/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 44 g01398438
47. Remove thrust disc (80).
48. Repeat Steps 25 through 30 for the disassembly of the clutch pack.
Illustration 45 g01398560
49. Attach Tooling (J) and a suitable lifting device to first gear and third gear clutch group (81).
The weight of clutch group (81) is approximately 45 kg (100 lb). Remove clutch group (81).
Illustration 46 g01398561
50. Remove retaining ring (82), thrust disc (83), and gear (84).
22/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 47 g01398645
51. Use Tooling (H) to remove retaining ring (86). Use Tooling (L) to remove hub (85) from
gear (84).
Illustration 48 g01398657
52. Use Tooling (K) to remove retaining ring (87). Use Tooling (L) to remove bearing (88)
from hub (85).
23/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 49 g01398664
53. Remove thrust disc (89).
54. Repeat Steps 25 through 30 for the disassembly of the clutch pack.
Illustration 50 g01398562
Illustration 51 g01398564
55. Install Tooling (Q), as shown. Use Tooling (Q) to remove bearing (90). Extend the cylinder
several times to remove bearing (90). Use spacers, as needed.
24/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 52 g01398565
56. Remove spacer (91) and gear (92).
Illustration 53 g01398567
57. Remove thrust disc (93) and gear (94).
Illustration 54 g01398773
58. Use Tooling (H) to remove retaining ring (95). Remove hub (96) from gear (94). Use
Tooling (L) to remove bearing (97).
Illustration 55 g01398774
25/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 59. Remove thrust disc (98) and washer (99).
Illustration 56 g01398776
60. Remove retaining ring (100) and plate (101).
61. Remove clutch plates and discs (103).
Note: Note the positions of the plates and discs for assembly purposes.
62. Remove retaining ring (102).
Illustration 57 g01398814
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
26/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 63. Position Tooling (R) onto seal assembly (105). Use Tooling (R) and a suitable press to
compress the clutch spring. Remove retaining ring (104). Slowly release the spring tension.
Illustration 58 g01398781
64. Remove ring (106) and seal assembly (105).
Illustration 59 g01398796
65. Remove spring (107) and piston (108).
Illustration 60 g01398985
66. Remove seals (109).
27/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 61 g01398975
67. Remove input shaft assembly (110).
Illustration 62 g01399007
68. Use a suitable press to remove carrier (111) and bearing cone (113). Remove ring seal (112)
from carrier (111). Remove gear (114).
69. Use a suitable press to remove bearing cone (116). Remove gear (115).
28/33
924H Wheel Loader HXC00001-03268 (MACHINE) POWERED BY C6.6 Engine(...
2021/1/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading