This document provides assembly instructions for a transmission and torque converter in 3 steps:
1. It lists the required tools and cleaning/inspection procedures.
2. It provides 35 steps to assemble components like seals, bearings, gears, and clutches for the transmission.
3. It notes additional steps to assemble the second gear clutch pack using different tooling. Cleanliness and torque specifications are emphasized throughout assembly.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix AAN) Service Repair Manua...9fikslkddmd8u
This document provides assembly instructions for a power shift transmission in a 924G wheel loader. It outlines 56 steps to assemble the transmission components, including installing bearings and seals, assembling various clutch packs, and attaching housing components. Tools required include presses, heaters, installers, and sealants. Proper cleaning and lubrication of parts is emphasized. Torque specifications are provided for housing bolts.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix 3PZ) Service Repair Manua...9fikslkddmd8u
This document provides instructions for assembling the power shift transmission for 924G and 924Gz wheel loaders. It outlines 54 steps to assemble the various components, including installing gears, bearings, seals, pistons, springs, plates, discs, hubs and other parts. Tools required are listed. Cleanliness is important during assembly to prevent contamination. Torque specifications are provided for certain fasteners. References are made to other documents for specifications on components like clutch discs and procedures to measure running clearances.
This document provides instructions for servicing a 924K wheel loader. It lists 66 steps to disassemble and reassemble components of the transmission, including installing seals, bearings, sensors, shafts and housing components. Precise torques and tools are specified. Safety precautions are noted for installing spring-loaded parts.
This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using special tools to compress springs, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
This document provides assembly instructions for a transmission and torque converter in a wheel loader. It lists required tools and parts and provides step-by-step instructions with illustrations. The instructions involve assembling bearings, seals, gears, clutches, shafts and other components in a precise order while maintaining cleanliness and lubrication. Special tools and heating/cooling of some parts is required to properly assemble the transmission.
This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using specialized tools to compress springs, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using specialized tools, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
This document provides assembly instructions for a transmission and torque converter in a wheel loader. It lists required tools and parts and provides step-by-step instructions with illustrations. The instructions include installing bearings and seals, assembling clutch packs, installing gears and shafts, and setting end play. Cleanliness is emphasized and inspecting components for wear or damage before assembly is noted.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix AAN) Service Repair Manua...9fikslkddmd8u
This document provides assembly instructions for a power shift transmission in a 924G wheel loader. It outlines 56 steps to assemble the transmission components, including installing bearings and seals, assembling various clutch packs, and attaching housing components. Tools required include presses, heaters, installers, and sealants. Proper cleaning and lubrication of parts is emphasized. Torque specifications are provided for housing bolts.
Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix 3PZ) Service Repair Manua...9fikslkddmd8u
This document provides instructions for assembling the power shift transmission for 924G and 924Gz wheel loaders. It outlines 54 steps to assemble the various components, including installing gears, bearings, seals, pistons, springs, plates, discs, hubs and other parts. Tools required are listed. Cleanliness is important during assembly to prevent contamination. Torque specifications are provided for certain fasteners. References are made to other documents for specifications on components like clutch discs and procedures to measure running clearances.
This document provides instructions for servicing a 924K wheel loader. It lists 66 steps to disassemble and reassemble components of the transmission, including installing seals, bearings, sensors, shafts and housing components. Precise torques and tools are specified. Safety precautions are noted for installing spring-loaded parts.
This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using special tools to compress springs, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
This document provides assembly instructions for a transmission and torque converter in a wheel loader. It lists required tools and parts and provides step-by-step instructions with illustrations. The instructions involve assembling bearings, seals, gears, clutches, shafts and other components in a precise order while maintaining cleanliness and lubrication. Special tools and heating/cooling of some parts is required to properly assemble the transmission.
This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using specialized tools to compress springs, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
This document provides instructions for assembling the transmission and torque converter of a 924H wheel loader. It lists required tools and gives step-by-step instructions with illustrations. Some key steps include installing bearings and seals, assembling various clutch packs using specialized tools, and ensuring proper end play and lubrication during assembly. Cleanliness and heating/cooling parts as needed during assembly is emphasized to avoid damage.
This document provides assembly instructions for a transmission and torque converter in a wheel loader. It lists required tools and parts and provides step-by-step instructions with illustrations. The instructions include installing bearings and seals, assembling clutch packs, installing gears and shafts, and setting end play. Cleanliness is emphasized and inspecting components for wear or damage before assembly is noted.
Caterpillar cat 992 k wheel loader (prefix zmx) service repair manual (zmx000...fjjskkdmnsme
This document provides assembly instructions for a torque converter used in a 992K wheel loader. It lists over 40 steps and references various tools and components. Key steps include installing seals and bearings onto shafts, positioning carrier and gear assemblies weighing up to 57kg, and checking bearing end play using dial indicators to ensure proper clearance of 0.10±0.05mm. The overall process assembles the various internal components of the torque converter in the correct order.
Caterpillar cat 992 k wheel loader (prefix zmx) service repair manual (zmx000...fjjskqweekfsmem
This document provides assembly instructions for a torque converter used in a 992K wheel loader. It lists over 60 steps and accompanying illustrations to assemble the various components of the torque converter in the proper order. Key components include seals, bearings, gears, plates, pistons, discs, sleeves, and housings. Special tools and lifting devices are required due to the large size and weights of components, which range from 25-680 kg. Proper temperatures and torques are specified for a safe and accurate reassembly of the torque converter.
Caterpillar cat 992 k wheel loader (prefix zmx) service repair manual (zmx000...fudjsjfekskkem
This document provides assembly instructions for a torque converter used in a 992K wheel loader. It lists over 60 steps and accompanying illustrations to assemble the various components of the torque converter in the proper order. Key components include seals, bearings, gears, plates, pistons, discs, sleeves, and housings. Special tools and lifting devices are required due to the large size and weights of components, which range from 25-680 kg. Proper temperatures and torques are specified for a safe and accurate reassembly of the torque converter.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, seals, gears, discs, plates, pistons, housings and other components. Proper cleaning, lubrication, and use of installation tools are emphasized.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a planetary transmission used in a 972H wheel loader. It describes how to assemble the input shaft, carrier assemblies, clutch components, output shaft, and other parts. Detailed steps and illustrations are provided to guide technicians through the assembly process. Cleanliness is emphasized and special tools are required to properly install some components like bearings. The assembly involves over 40 individual steps and requires lifting heavy parts into place.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections detailing the assembly of the transmission's planetary gear sets and clutches. The summary includes:
1) Cleaning and preparing transmission components before assembly.
2) Assembling the three planetary gear sets which include installing bearings, gears, shafts, seals and retaining rings.
3) Installing clutches which involve alternating friction discs and plates, installing seals, pistons and springs.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, gears, seals, springs, and other components. Proper cleaning and use of installation tools are noted.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, gears, seals, springs, and other components. Proper cleaning and use of installation tools are emphasized.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, gears, seals, springs, and other components. Proper cleaning and use of installation tools are emphasized.
This document provides assembly instructions for a 992K wheel loader torque converter. It lists over 60 steps and required tools to assemble the various components of the torque converter. Key parts that are assembled include the shaft assembly, carrier assembly, gears, housing assembly, impeller clutch, turbine assembly, clutch housing assembly, and pump adapters. Lifting devices and special tools are required due to the heavy weights of components like the housing assembly and impeller clutch.
This document provides assembly instructions for a torque converter in a 992K wheel loader. It lists over 40 steps and required tools to assemble internal components like seals, bearings, gears, and housings. Proper lifting equipment is needed due to component weights up to 590kg. Tolerances and torque specifications are provided.
This document provides assembly instructions for a 992K wheel loader torque converter. It lists over 60 steps and required tools to assemble the various components of the torque converter. Key parts that are assembled include the shaft assembly, carrier assembly, gears, housing assembly, impeller clutch, turbine assembly, clutch housing assembly, and pump adapters. Lifting devices and special tools are required due to the heavy weights of components like the housing assembly and impeller clutch.
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking disconnected parts for installation and preventing fluid loss.
The document provides instructions for disassembling and assembling a torque converter. It describes 18 steps to disassemble the torque converter by removing various parts like housing assemblies, bearings, plates, and seals. It then describes 18 steps for assembling the torque converter by installing the parts in reverse order. Tools required include link brackets, drivers, and forcing screws. Safety precautions are provided for spring loaded parts.
The document provides instructions for removing and assembling the torque converter of a 730 Ejector Articulated Truck. It describes in 18 steps how to disassemble the torque converter by removing components like the housing assembly, piston, plates and discs, impeller, and turbine. It then describes in 12 steps the process of assembling the torque converter by reinstalling these components in reverse order, taking care to keep parts clean and install springs and other parts correctly. Special tools are required for tasks like removing the plate and installing the cam.
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 34 steps to assemble the various components of the torque converter, including housings, bearings, seals, discs, and shafts. Personal protective equipment is required and cleanliness is emphasized throughout the process. Torque specifications are provided for securing each component with bolts or screws.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing bolts and clips, and installing requires applying sealant
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a Caterpillar C11 engine. The removal process involves using various tools to remove components like the rear crankshaft seal, adapter assembly, gears, bearings and covers. The installation process provides steps to install these components in reverse order and notes that components like bearings must be cooled and properly positioned during installation. Precise dimensions and torque specifications are given for correct installation.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C13 engine.
The removal procedure includes supporting the engine, removing bolts and seals to access the rear gear group components, and using various tools to remove gears, bushings, bearings, and covers. The installation procedure provides instructions for cleaning parts, lowering temperatures of bearings, applying sealant to bolts, and orienting gears and bearings according to specified dimensions before reinstalling the components in reverse order of removal. Separate sections also provide procedures for removing and installing the flywheel and rear crankshaft seal.
More Related Content
Similar to Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix WMB) Service Repair Manual Instant Download.pdf
Caterpillar cat 992 k wheel loader (prefix zmx) service repair manual (zmx000...fjjskkdmnsme
This document provides assembly instructions for a torque converter used in a 992K wheel loader. It lists over 40 steps and references various tools and components. Key steps include installing seals and bearings onto shafts, positioning carrier and gear assemblies weighing up to 57kg, and checking bearing end play using dial indicators to ensure proper clearance of 0.10±0.05mm. The overall process assembles the various internal components of the torque converter in the correct order.
Caterpillar cat 992 k wheel loader (prefix zmx) service repair manual (zmx000...fjjskqweekfsmem
This document provides assembly instructions for a torque converter used in a 992K wheel loader. It lists over 60 steps and accompanying illustrations to assemble the various components of the torque converter in the proper order. Key components include seals, bearings, gears, plates, pistons, discs, sleeves, and housings. Special tools and lifting devices are required due to the large size and weights of components, which range from 25-680 kg. Proper temperatures and torques are specified for a safe and accurate reassembly of the torque converter.
Caterpillar cat 992 k wheel loader (prefix zmx) service repair manual (zmx000...fudjsjfekskkem
This document provides assembly instructions for a torque converter used in a 992K wheel loader. It lists over 60 steps and accompanying illustrations to assemble the various components of the torque converter in the proper order. Key components include seals, bearings, gears, plates, pistons, discs, sleeves, and housings. Special tools and lifting devices are required due to the large size and weights of components, which range from 25-680 kg. Proper temperatures and torques are specified for a safe and accurate reassembly of the torque converter.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, seals, gears, discs, plates, pistons, housings and other components. Proper cleaning, lubrication, and use of installation tools are emphasized.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a planetary transmission used in a 972H wheel loader. It describes how to assemble the input shaft, carrier assemblies, clutch components, output shaft, and other parts. Detailed steps and illustrations are provided to guide technicians through the assembly process. Cleanliness is emphasized and special tools are required to properly install some components like bearings. The assembly involves over 40 individual steps and requires lifting heavy parts into place.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections detailing the assembly of the transmission's planetary gear sets and clutches. The summary includes:
1) Cleaning and preparing transmission components before assembly.
2) Assembling the three planetary gear sets which include installing bearings, gears, shafts, seals and retaining rings.
3) Installing clutches which involve alternating friction discs and plates, installing seals, pistons and springs.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, gears, seals, springs, and other components. Proper cleaning and use of installation tools are noted.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, gears, seals, springs, and other components. Proper cleaning and use of installation tools are emphasized.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, gears, seals, springs, and other components. Proper cleaning and use of installation tools are emphasized.
This document provides assembly instructions for a 992K wheel loader torque converter. It lists over 60 steps and required tools to assemble the various components of the torque converter. Key parts that are assembled include the shaft assembly, carrier assembly, gears, housing assembly, impeller clutch, turbine assembly, clutch housing assembly, and pump adapters. Lifting devices and special tools are required due to the heavy weights of components like the housing assembly and impeller clutch.
This document provides assembly instructions for a torque converter in a 992K wheel loader. It lists over 40 steps and required tools to assemble internal components like seals, bearings, gears, and housings. Proper lifting equipment is needed due to component weights up to 590kg. Tolerances and torque specifications are provided.
This document provides assembly instructions for a 992K wheel loader torque converter. It lists over 60 steps and required tools to assemble the various components of the torque converter. Key parts that are assembled include the shaft assembly, carrier assembly, gears, housing assembly, impeller clutch, turbine assembly, clutch housing assembly, and pump adapters. Lifting devices and special tools are required due to the heavy weights of components like the housing assembly and impeller clutch.
Similar to Caterpillar Cat 924G and 924Gz Wheel Loader (Prefix WMB) Service Repair Manual Instant Download.pdf (15)
The document provides instructions for removing the implement vane pump from a 657G Wheel Scraper. It describes disconnecting hoses and wiring, draining fluid from the elbow, attaching a lifting device to the pump, and removing nuts and the pump. It also includes notes about marking disconnected parts for installation and preventing fluid loss.
The document provides instructions for disassembling and assembling a torque converter. It describes 18 steps to disassemble the torque converter by removing various parts like housing assemblies, bearings, plates, and seals. It then describes 18 steps for assembling the torque converter by installing the parts in reverse order. Tools required include link brackets, drivers, and forcing screws. Safety precautions are provided for spring loaded parts.
The document provides instructions for removing and assembling the torque converter of a 730 Ejector Articulated Truck. It describes in 18 steps how to disassemble the torque converter by removing components like the housing assembly, piston, plates and discs, impeller, and turbine. It then describes in 12 steps the process of assembling the torque converter by reinstalling these components in reverse order, taking care to keep parts clean and install springs and other parts correctly. Special tools are required for tasks like removing the plate and installing the cam.
This document provides assembly instructions for a torque converter in a 730 articulated truck. It lists 34 steps to assemble the various components of the torque converter, including housings, bearings, seals, discs, and shafts. Personal protective equipment is required and cleanliness is emphasized throughout the process. Torque specifications are provided for securing each component with bolts or screws.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing bolts and clips, and installing requires applying sealant
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a Caterpillar C11 engine. The removal process involves using various tools to remove components like the rear crankshaft seal, adapter assembly, gears, bearings and covers. The installation process provides steps to install these components in reverse order and notes that components like bearings must be cooled and properly positioned during installation. Precise dimensions and torque specifications are given for correct installation.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C13 engine.
The removal procedure includes supporting the engine, removing bolts and seals to access the rear gear group components, and using various tools to remove gears, bushings, bearings, and covers. The installation procedure provides instructions for cleaning parts, lowering temperatures of bearings, applying sealant to bolts, and orienting gears and bearings according to specified dimensions before reinstalling the components in reverse order of removal. Separate sections also provide procedures for removing and installing the flywheel and rear crankshaft seal.
This document provides instructions for removing and installing various engine components on a Caterpillar C9.3 engine, including the valve mechanism cover, compression brake, and rocker arm shaft assembly. The procedures describe disconnecting wiring harnesses, removing nuts and bolts, checking and replacing seals, lubricating parts, and tightening components to the specified torques. Tools required include a feeler gauge and lubricant. Identification marks should be made on removed parts and the components must be kept clean to prevent premature wear.
The document provides instructions for removing and disassembling the drive shaft and scavenge pump on a 657G Wheel Scraper. Key steps include:
1. Removing retaining rings, covers, and guards to access the drive shaft.
2. Using eyebolts and lifting devices to remove the heavy drive shaft and tube assembly.
3. Checking alignment of components and removing the yoke assembly, bearings, and seals from the bearing cage.
4. Disassembling the flywheel scavenge pump by removing bolts, seals, bearings, and shafts.
This document provides instructions for installing and removing various engine components on a Caterpillar 657E wheel scraper model powered by a 3408 engine, including:
1) Installing the rear gear group by placing gears and bearings on shafts and installing dowels, seals and bolts.
2) Removing the flywheel using guide bolts, brackets and a hoist to lift the heavy flywheel off the crankshaft.
3) Installing the flywheel by heating the ring gear, placing the flywheel on guide bolts, and bolting it into place.
4) Procedures for removing and installing the crankshaft rear seal using pullers and punches
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 657E wheel tractor, including:
- Removing the rear gear group by pressing components out of adapter assemblies, using pullers to remove bearings, and disassembling individual gears.
- Installing the rear gear group by pressing bearings into place, assembling individual gears, and pressing assembled components into adapter assemblies.
- Removing the flywheel by using bolts, guide bolts, and a lifting bracket to pull the flywheel off the crankshaft.
- Installing the flywheel by using guide bolts to position it, applying lubricant to bolts, and tightening bol
This document provides instructions for disassembling and assembling the transmission transfer gears of a Caterpillar 651E wheel tractor. The steps include removing the transmission transfer gears as a unit, disassembling the individual gears and bearings, inspecting and replacing parts, and reassembling the gears and bearings in the correct order with the specified tools and torques. Proper installation of seals, shims, and torque specifications are emphasized to ensure correct assembly.
This document provides instructions for removing and installing the rear crankshaft seal on a Caterpillar 651E wheel scraper. The removal procedure involves using a slide hammer puller to pull the rear crankshaft seal from the flywheel housing. The installation procedure specifies cleaning and lubricating the crankshaft and seal bore before pressing the new seal into place. Proper cleaning and lubrication are emphasized to prevent contaminating and shortening the life of components.
The document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It lists the required tools and presents 24 steps to disassemble the various components of the torque converter. These include removing the housing assembly, torque converter assembly, clutch piston, friction disk, bearings, seals and gears. The assembly section then lists the same 24 steps in reverse order to reassemble all components back into the torque converter.
This document provides instructions for disassembling and assembling the torque converter of a 637K Wheel Tractor Scraper. It describes 18 steps to disassemble the torque converter by removing parts like the retaining rings, bolts, thrust bearings, and seals. It then describes 24 steps to reassemble the torque converter by installing the parts in the reverse order, applying sealant or heat treating some parts as needed. Tools required include retaining ring pliers, drivers, pullers, and link brackets to lift components.
The document provides instructions for disassembling various components of a 637G wheel tractor, including the transfer gears, torque converter, and transmission. The transfer gear case is first removed from the transmission. Then the torque converter is disassembled by removing components like the impeller, carrier assembly, stator, and turbine. Finally, instructions are given to disassemble the transfer gears by removing items such as bearings and seals. Tools are listed that are required for the disassembly procedures.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Tractor. It describes removing over 30 individual components in multiple steps, including removing the torque converter housing, retarder, gears, bearings, seals and other internal parts. Detailed illustrations accompany each step. Cleanliness is emphasized to prevent contaminating the hydraulic system.
The document provides instructions for disassembling and assembling the torque converter of a 637G Wheel Scraper. It lists 32 steps for disassembly that include removing retaining rings, seals, gears, shafts, bearings, and housing assemblies. It then lists 31 steps for assembly in reverse order, providing details on cleaning parts, heating and cooling bearings, and proper torque specifications for fasteners. Tools required are also listed.
This document provides instructions for disassembling and assembling the transfer gears of a 627G wheel tractor. The disassembly process involves removing 18 components from the transfer gear case including bearing cages, gears, shims, and cups. The assembly process describes installing these components in the reverse order and includes lubricating seals, heating/cooling bearings, and torquing bolts to the specified values.
This document provides instructions for disassembling and assembling the torque converter of a 627G Wheel Scraper. It outlines 32 steps to disassemble the various components of the torque converter including the housing, gears, shafts, bearings, and other parts. It then outlines 29 steps for assembling the torque converter components back together in reverse order. Required tools are listed for specific disassembly and assembly steps. Safety notices are provided to contain fluids and properly dispose of them.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 924G WHEEL LOADER WMB
Configuration: 924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Power
Train
Media Number -RENR6422-07 Publication Date -01/10/2017 Date Updated -09/10/2017
i06103589
Transmission and Torque Converter - Assemble
SMCS - 3001-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 180-3033 Repair Stand Set 1
C 138-7574 Link Bracket 2
D 4C-6136 Lifting Bracket 1
E 4C-6399 Compressor Assembly (Clutch Spring) 1
F FT-2343 Plexiglass Cover 1
H 4C-3652 Compressor Assembly (Clutch Spring) 1
J 4C-6402 Expander Tool Gp 1
K
4C-6137 Bearing Installer 1
4C-6142 Spacer 1
1P-0531 Handle 1
L 5P-3413 Pipe Sealant 1
M 9S-3263 Thread Lock Compound 1
N 1U-8846 Gasket Sealant 1
1/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. P 4C-6143 Clutch Piston Installer 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01005243
1. Install gear (149) and retaining ring (148) . Raise the temperature of bearing cone (147) .
Install bearing cone (147) .
Illustration 2 g01005241
2. Raise the temperature of bearing cone (146) . Install bearing cone (146) .
2/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01005239
3. Apply Tooling (L) to the seal bore.
4. Install lip seal (145) . Lubricate the sealing lip with the lubricant that is being used.
5. Lower the temperature of bearing cup (143) . Install bearing cup (143) .
6. Use bolts (142) in order to install shield assembly (144) . Tighten bolts (142) to a torque of
55 ± 10 N·m (40 ± 10 lb ft).
Illustration 4 g01005238
7. Install the output shaft and gear (141) .
3/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01005236
8. Install lip seal (140) . Lubricate the sealing lip with the lubricant that is being used.
9. Lower the temperature of bearing cup (139) . Install bearing cup (139) .
10. Install seal (138) .
11. Install shims (137) . Use the shims in order to get 0.06 mm (0.002 inch) to 0.13 mm (0.005
inch) end play on the output shaft.
Note: Lubricate the bore of the housing with the lubricant that is being used.
Illustration 6 g00655180
12. Use bolts (135) in order to install the cage. Tighten bolts (135) to a torque of 70 ± 10 N·m
(50 ± 10 lb ft).
4/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g00890758
13. Install parking brake assembly (133) and lever (134) .
14. Use bolts (131) in order to install plate (132) . Tighten bolts (131) to a torque of 120 ± 20
N·m (90 ± 15 lb ft).
Illustration 8 g00890622
15. Install brake drum (130) and yoke (129) together. Install seal (128) .
5/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 9 g00685060
16. Install the bolt and washer (127) . Tighten bolt (127) to a torque of 120 ± 20 N·m (90 ± 15
lb ft).
Illustration 10 g00655120
17. Use washer (125) and bolt (124) in order to install yoke (126) . Tighten bolt (124) to a
torque of 120 ± 20 N·m (90 ± 15 lb ft).
Illustration 11 g00655110
18. Lower the temperature of bearing cups (123) . Install bearing cups (123) . Use Tooling (J) to
install bearing (122) .
6/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g00890621
19. Install gear (119) . Raise the temperature of bearing cone (118) . Install bearing cone (118) .
20. Install gear (120) . Raise the temperature of bearing cone (121) . Install bearing cone (121) .
21. Install seal (116) on carrier (117) and install carrier (117) .
Illustration 13 g00655016
22. Install the input shaft assembly (115) .
7/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g00654969
23. Install seals (112) , (113) , and (114) .
Illustration 15 g00654966
Note: Lubricate the piston, and the bore with clean transmission oil.
24. Use Tooling (P) in order to install piston (111) .
Illustration 16 g00654842
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
8/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 25. Install spring (110) .
Illustration 17 g00654837
26. Install the retainer and seal assembly (109) .
Illustration 18 g00654833
27. Put the clutch pack in a suitable press. Use Tooling (H) in order to install retaining ring
(108) .
9/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E En...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g00654824
28. Lower the temperature of bearing assembly (107) . Install bearing assembly (107) .
Illustration 20 g00654818
29. Install ring (106) .
Illustration 21 g00890619
10/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Note: Refer to Specifications, "Power Shift Transmission" for the specifications of the
clutch discs.
30. Install plates and discs (105) . Install retaining ring (103) . Install washers (104) and (102) .
Illustration 22 g00654724
31. Install hub assembly (101) .
Illustration 23 g00654719
32. Install gear (100) and retaining ring (99) . Install washer (98) .
11/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 24 g00656434
33. Install gear (95) and washer (96) . Raise the temperature of bearing (97) . Install bearing
(97) .
Note: This completes the assembly of the first gear clutch pack.
Note: Refer to Specifications, "Power Shift Transmission" for the procedure to measure
running clearance.
Illustration 25 g00654638
34. Install seals (94) and (93) .
12/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 26 g00890838
Note: Lubricate the piston, and the bore with clean transmission oil.
35. Use Tooling (P) in order to install piston (90) .
36. Install seals (92) on shaft (91) .
Illustration 27 g00654534
37. Install spring (89) and retainer (88) .
13/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 28 g00654525
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
38. Put the third gear clutch pack in a suitable press. Use Tooling (H) in order to install
retaining ring (87) .
Illustration 29 g00654519
Note: Refer to Specifications, "Power Shift Transmission" for the specifications of the
clutch discs.
39. Install plates and discs (86) . Install retaining ring (85) .
40. Install washer (84) .
14/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 30 g00654517
41. Use a suitable press in order to install bearing (83) . Install retaining ring (82) .
Illustration 31 g00654512
42. Install hub assembly (81) .
Illustration 32 g00654507
43. Install gear (80) and retaining ring (79) .
15/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 33 g00654497
44. Install washer (78) and retaining ring (77) .
Note: This completes the assembly of the third gear clutch pack.
Note: Refer to Specifications, SENR3504, "Power Shift Transmission" for the procedure to
measure running clearance .
Illustration 34 g00654494
45. Use Tooling (D) in order to install third gear clutch pack (76) . The weight of third gear
clutch pack (76) is approximately 50 kg (110 lb).
16/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 35 g00890612
Note: Use Steps 46 through 49 for the assembly of the clutch of the second gear clutch
pack. Use Tooling (E) in step 49 instead of Tooling (H) .
46. Install washers (75) and (74) . Install spacer (73) .
47. Install gear (72) , spacer (70) , and bearing cone (71) .
Illustration 36 g00654403
48. Install seals (69) and (68) .
17/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 37 g00890841
Illustration 38 g00654372
Note: Lubricate the piston and the bore with clean transmission oil.
49. Use Tooling (P) in order to install piston (65) . Install seals (66) on shaft (67) .
Illustration 39 g00654364
50. Install spring (64) and retainer (63) .
18/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 40 g00654360
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
51. Put the reverse clutch pack in a suitable press. Use Tooling (H) in order to install retaining
ring (62) .
Illustration 41 g00890611
52. Use a suitable press in order to install bearing (61) . Install retaining ring (60) .
19/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 42 g00890610
Note: Refer to Specifications, "Power Shift Transmission" for the specifications of the
clutch discs.
53. Install plates and discs (59) . Install retaining ring (57) .
54. Install washer (58) .
Illustration 43 g00654347
55. Install hub assembly (56) .
20/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 44 g00654328
56. Install gear (55) and retaining ring (54) .
Illustration 45 g00654339
57. Install washer (53) and retaining ring (52) .
Note: This completes the assembly of the reverse second gear clutch pack.
Note: Refer to Specifications, "Power Shift Transmission" for the procedure to measure
running clearance.
21/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 46 g00654301
58. Use Tooling (D) in order to install reverse second gear clutch pack (51) . The weight of
reverse second gear clutch pack (51) is approximately 32 kg (70 lb).
Illustration 47 g00654292
59. Install seals (49) and (50) .
Illustration 48 g00654280
22/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Note: Lubricate the piston, and the bore with clean transmission oil.
60. Use Tooling (P) in order to install piston (47) .
61. Install spring (46) and retainer (45) .
Illustration 49 g00654276
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
62. Put the forward high clutch pack in a suitable press. Use Tooling (H) in order to install
retaining ring (44) .
23/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 50 g00654274
Note: Refer to Specifications, "Power Shift Transmission" for specifications of the clutch
discs.
63. Install plates and discs (43) . Install retaining ring (42) . Install washer (41) .
Illustration 51 g00654263
64. Use a suitable press in order to install bearing (40) . Install retaining ring (39) .
Illustration 52 g00654261
65. Install hub (38) .
24/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 53 g00654253
66. Raise the temperature of gear (37) . Install gear (37) . Install retaining ring (36) .
Illustration 54 g00654078
67. Install washer (35) and retaining ring (34) .
Note: This completes the assembly of the forward high gear clutch pack.
Note: Refer to Specifications, "Power Shift Transmission" for the procedure to measure
running clearance.
25/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 55 g00654063
68. Install O-ring seals (33) .
Illustration 56 g00890845
Note: Lubricate the piston, and the bore with clean transmission oil.
69. Use Tooling (P) in order to install piston (31) . Install seals (32) on shaft (30) .
Illustration 57 g00654029
26/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 70. Install spring (29) and retainer (28) .
Illustration 58 g00654018
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
71. Put the forward low clutch pack in a suitable press. Use Tooling (H) in order to compress
the spring. Install retaining ring (27) .
Illustration 59 g00890608
72. Use a suitable press in order to install bearing (25) . Install retaining ring (26) in hub (22) .
27/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 60 g00653959
73. Install washer (24) .
Illustration 61 g00890607
Note: Refer to Specifications, "Power Shift Transmission" for specifications of clutch discs.
74. Install plates and discs (23) . Install hub (21) . Install retaining ring (22) .
28/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 62 g00653932
75. Raise the temperature of gear (20) . Install gear (20) . Install retaining ring (19) .
Illustration 63 g00653893
76. Install washer (18) and retaining ring (17) .
Note: This completes the assembly of the forward low gear clutch pack.
Note: Refer to Specifications, "Power Shift Transmission" for the procedure to measure
running clearance.
Illustration 64 g00653858
77. Use Tooling (D) in order to install the forward low and the forward high clutch pack (15) .
The weight of forward high clutch pack (15) is approximately 27 kg (60 lb).
Note: Use Tooling (J) in order to install plugs (16) .
29/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
32. Illustration 65 g00653848
78. Lower the temperature of bearing cups (14) . Use Tooling (K) in order to install bearing
cups (14) .
Illustration 66 g00653825
79. Use bolts (12) in order to install gear (13) . Tighten bolts (12) to a torque of 12 ± 3 N·m (10
± 2 lb ft).
Illustration 67 g00653808
30/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. 80. Install gear assembly (10) .
81. Install O-ring seals (11) .
Illustration 68 g00653806
82. Install bolts (9) . Tighten bolts (9) to a torque of 55 ± 10 N·m (40 ± 10 lb ft).
Illustration 69 g00653801
83. ApplyTooling (L) to the seal bore.
84. Install lip seal (7) . Lubricate the sealing lip with the lubricant that is being used.
85. Install seal (8) .
31/35
924G 924Gz Wheel Loader WMB00001-UP (MACHINE) POWERED BY 3056E ...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...