The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck powered by a C13 engine. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various transmission components on a Caterpillar 730C2 articulated truck, including:
1. Removing and installing the torque converter housing, which requires attaching lifting devices and brackets due to the housing's weight of approximately 500 lbs.
2. Removing and installing the pump drive, which also must be lifted due to its weight of 70 lbs, and includes removing O-rings from the housing.
3. Procedures for removing and installing the accessory drive, idler gear, and relief valve on the transmission, noting required tools and order of removal/installation steps.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing components like the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The procedures describe the required tools and parts, safety precautions, step-by-step instructions, and torque specifications. Illustrations are provided to supplement the written instructions.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing components like the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The procedures describe the required tools and parts, safety precautions, step-by-step instructions, and torque specifications. Illustrations are provided to supplement the written instructions.
The document provides instructions for removing and installing components of the torque converter housing and pump drive on a Caterpillar 730C2 articulated truck. The removal procedure includes using lifting devices and tools to detach the torque converter housing and pump drive. Components like bolts, seals and manifolds are then removed from the housing and drive.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck. The instructions include removing the torque converter housing, pump drive, accessory drive, idler gear, and relief valve. Tools required are listed, along with torque specifications and other details needed to correctly complete the disassembly and reassembly procedures.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety notices are also provided regarding hot coolant and spilled fuel.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and ARD fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
The document provides instructions for removing and installing various transmission components on a Caterpillar 730C2 articulated truck, including:
1. Removing and installing the torque converter housing, which requires attaching lifting devices and brackets due to the housing's weight of approximately 500 lbs.
2. Removing and installing the pump drive, which also must be lifted due to its weight of 70 lbs, and includes removing O-rings from the housing.
3. Procedures for removing and installing the accessory drive, idler gear, and relief valve on the transmission, noting required tools and order of removal/installation steps.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing components like the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The procedures describe the required tools and parts, safety precautions, step-by-step instructions, and torque specifications. Illustrations are provided to supplement the written instructions.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing components like the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The procedures describe the required tools and parts, safety precautions, step-by-step instructions, and torque specifications. Illustrations are provided to supplement the written instructions.
The document provides instructions for removing and installing components of the torque converter housing and pump drive on a Caterpillar 730C2 articulated truck. The removal procedure includes using lifting devices and tools to detach the torque converter housing and pump drive. Components like bolts, seals and manifolds are then removed from the housing and drive.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck. The instructions include removing the torque converter housing, pump drive, accessory drive, idler gear, and relief valve. Tools required are listed, along with torque specifications and other details needed to correctly complete the disassembly and reassembly procedures.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety notices are also provided regarding hot coolant and spilled fuel.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and ARD fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety precautions are provided for tasks involving hot coolant or fuel.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and ARD fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety notices are also provided regarding hot coolant and spilled fuel.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety precautions are provided for tasks like working with pressurized coolant or fuel.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure lists 11 steps to remove the rear gear group which includes removing bolts, seals, gears, bushings and bearings. The installation procedure provides 12 steps and specifies tools and torque specifications to install the components in reverse order. A separate section provides procedures for removing and installing the flywheel, which includes using lifting equipment and installing with loctite and torqueing bolts to the specified value.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings and covers. The installation procedure provides steps to install these components in reverse order and includes cleaning and applying threadlocker to bolts. Tools required are also listed.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. The installation procedure provides steps to install the rear crankshaft seal, gears, covers and flywheel in the reverse order of removal. Tools required are also listed.
The document provides instructions for removing and disassembling a torque converter from a 730C2 articulated truck with a C13 engine. It lists the required tools and presents step-by-step instructions with accompanying illustrations. The instructions describe removing the torque converter housing, then disassembling internal components like the piston, plates, discs, bearings, and impeller. Reassembly instructions are also provided.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader with a 3054 engine. It describes the required tools and multi-step processes which include removing bolts, lifting devices, cleaning parts, and torquing fasteners to the specified values. The document contains illustrations supporting each step of the procedures.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...fujskkmdmd
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and rear crankshaft seal. Detailed illustrations and cautions are provided for each step. The process involves drilling holes in the crankshaft rear seal before removing it, cleaning and applying compounds to mating surfaces, and checking dowel pins and gaskets before reassembly.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and reinstalling the mounting bolts. Tools including link brackets and lifting devices are required.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and installing new seals is also covered. Dowels align the housing and bolts attach it to the cylinder block with specified torque.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The procedure involves using a drill bit to drill out the plastic sleeve holding the seal in place. Once drilled out, the seal can be removed from the front cover housing. Proper cleaning of parts and containment of fluids is emphasized to prevent contamination.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...fujskkmdmd
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and clamps, and disconnecting tubes and hoses to remove the cylinder head.
3. Installing a new gasket and torquing bolts to specified values to install the cylinder head. Reconnecting all tubes, hoses and harness assemblies.
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover by loosening the clamp.
3. Removing the bolts securing the regulator housing and removing the regulator from the engine.
The instructions emphasize cleanliness and safe handling of fluids during maintenance.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...fujskkmdmd
The document provides instructions for removing and installing a unit injector hydraulic pump on a 322C FM EXCAVATOR C3R powered by a 3126B engine. The removal procedure involves disconnecting hoses and lines, removing bolts, and taking off the pump. The installation procedure specifies lubricating seals, installing bolts, reconnecting lines and hoses, and ensuring connections are secure. Separate sections provide instructions for disassembling and assembling a turbocharger on the same engine model.
More Related Content
Similar to Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2T400001 and up).pdf
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety precautions are provided for tasks involving hot coolant or fuel.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and ARD fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety notices are also provided regarding hot coolant and spilled fuel.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
The document provides instructions for removing and installing various components related to the diesel exhaust fluid system for a Caterpillar 730C Ejector Articulated Truck. It includes illustrated step-by-step instructions for removing and installing items like the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. Safety precautions are provided for tasks like working with pressurized coolant or fuel.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides removal and installation instructions for various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector articulated truck. It describes how to remove and install the DEF tank, pump, injector, electronic control unit, and various solenoid valves. The instructions include illustrations showing the component locations and torque specifications for reinstalling components.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure lists 11 steps to remove the rear gear group which includes removing bolts, seals, gears, bushings and bearings. The installation procedure provides 12 steps and specifies tools and torque specifications to install the components in reverse order. A separate section provides procedures for removing and installing the flywheel, which includes using lifting equipment and installing with loctite and torqueing bolts to the specified value.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings and covers. The installation procedure provides steps to install these components in reverse order and includes cleaning and applying threadlocker to bolts. Tools required are also listed.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. The installation procedure provides steps to install the rear crankshaft seal, gears, covers and flywheel in the reverse order of removal. Tools required are also listed.
The document provides instructions for removing and disassembling a torque converter from a 730C2 articulated truck with a C13 engine. It lists the required tools and presents step-by-step instructions with accompanying illustrations. The instructions describe removing the torque converter housing, then disassembling internal components like the piston, plates, discs, bearings, and impeller. Reassembly instructions are also provided.
Similar to Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2T400001 and up).pdf (12)
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader with a 3054 engine. It describes the required tools and multi-step processes which include removing bolts, lifting devices, cleaning parts, and torquing fasteners to the specified values. The document contains illustrations supporting each step of the procedures.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...fujskkmdmd
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and rear crankshaft seal. Detailed illustrations and cautions are provided for each step. The process involves drilling holes in the crankshaft rear seal before removing it, cleaning and applying compounds to mating surfaces, and checking dowel pins and gaskets before reassembly.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and reinstalling the mounting bolts. Tools including link brackets and lifting devices are required.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and installing new seals is also covered. Dowels align the housing and bolts attach it to the cylinder block with specified torque.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The procedure involves using a drill bit to drill out the plastic sleeve holding the seal in place. Once drilled out, the seal can be removed from the front cover housing. Proper cleaning of parts and containment of fluids is emphasized to prevent contamination.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...fujskkmdmd
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and clamps, and disconnecting tubes and hoses to remove the cylinder head.
3. Installing a new gasket and torquing bolts to specified values to install the cylinder head. Reconnecting all tubes, hoses and harness assemblies.
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover by loosening the clamp.
3. Removing the bolts securing the regulator housing and removing the regulator from the engine.
The instructions emphasize cleanliness and safe handling of fluids during maintenance.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...fujskkmdmd
The document provides instructions for removing and installing a unit injector hydraulic pump on a 322C FM EXCAVATOR C3R powered by a 3126B engine. The removal procedure involves disconnecting hoses and lines, removing bolts, and taking off the pump. The installation procedure specifies lubricating seals, installing bolts, reconnecting lines and hoses, and ensuring connections are secure. Separate sections provide instructions for disassembling and assembling a turbocharger on the same engine model.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual (BPH0000...fujskkmdmd
This document provides instructions for removing and installing a governor from a 322C FM EXCAVATOR engine. It describes disconnecting linkages, removing mounting bolts and clips, and using special tools. Proper cleaning and lubrication of seals is emphasized. References are provided for additional information on governor inspection and testing procedures.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual (CAM0000...fujskkmdmd
The document provides instructions for removing the engine oil filter base from a 322C FM excavator. The procedure involves first removing the turbocharger. Then, using a strap wrench, loosen the oil filter base by turning it counterclockwise. Finally, clean the mating surface before installing the new oil filter base. The summary is provided in 3 sentences or less as requested.
Caterpillar Cat 320D L Excavator (Prefix KLM) Service Repair Manual (KLM00001...fujskkmdmd
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure involves using a slide hammer puller to remove the existing seal after drilling holes in it. For installation, a front seal installer tool is used to carefully push the new seal onto the crankshaft flange. Proper cleaning and containment of fluids is emphasized.
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and rear crankshaft seal. Detailed illustrations and cautions are provided for each step. The process involves drilling holes in the crankshaft rear seal before removing it, cleaning and applying compounds to mating surfaces, and checking dowel pins and gaskets before reassembly.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix EC2) Service Repair ...fujskkmdmd
This document provides instructions for removing and installing various engine components on a Caterpillar 308E2CR Mini Hydraulic Excavator, including the fuel injection pump, electronic unit injectors, turbocharger, and mass air flow pressure sensor. The procedures describe using required tools, disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components in the reverse order while applying specified torques. Safety notices warn technicians to allow the fuel system to purge before opening lines and ensure components like the mass air flow sensor are oriented correctly.
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...fujskkmdmd
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
This document provides instructions for removing the crankshaft front seal from a Caterpillar C6.4 engine. The procedure involves using a slide hammer puller tool to remove the seal from the front of the crankshaft. Technicians are advised to keep all parts clean and contain fluids properly during repair work. Removal of the seal prepares the engine for further disassembly or repair of crankshaft components.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fujskkmdmd
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...fujskkmdmd
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal, wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures include using various tools to remove components, cleaning parts, applying sealant or oil, and torquing bolts to the specified values. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix W8S) Service Repair ...fujskkmdmd
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator, including:
- Removing and installing the diesel particulate filter.
- Removing and installing the inlet manifold.
- Removing and installing the inlet and exhaust valve springs.
- Removing and installing the inlet and exhaust valves.
Detailed step-by-step instructions are provided along with illustrations to correctly complete each procedure. Safety precautions and notes are included throughout.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i07526804
Torque Converter Housing - Install
SMCS - 3105-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B - Loctite 242 -
C 385-4000 Seal Installation Tool 1
D - Loctite Flange Sealant 5900 -
Illustration 1 g03129265
1. Install studs (9) if removed. Install seal (8).
1/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g03129058
Illustration 3 g03129157
2. Attach Tooling (A) and a suitable lifting device to torque converter housing. The weight of
torque converter housing (5) is approximately 227 kg (500 lb). Install torque converter
housing (5).
3. Apply Tooling (D) to the housing spotface and washer of bolt (7).
Note: Remove excess sealant after bolt (7) is torqued.
4. Install bolt (7). Apply Tooling (B) to the threads of studs (9). Install nuts (6). Tighten bolt
(7) and nuts (6) to a torque of 100 ± 20 N·m (74 ± 15 lb ft).
2/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g03129025
5. Connect harness assembly and cable strap (4).
Illustration 5 g03129017
6. Connect harness assembly (2) and cable straps (3).
Illustration 6 g03128943
7. Use Tooling (C) and Install lip seal (1) dry.
End By:
a. Install the gear pump (scavenge transmission).
b. Install the torque converter.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:48:04 UTC+0800 2019
3/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04947892
Relief Valve (Torque Converter Inlet) - Remove and Install
SMCS - 3133-010-OL
Removal Procedure
Start By:
a. Remove the pump drive.
Illustration 1 g03141720
1. Remove bolts (1) and bolt (3). Remove manifold (2).
1/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 5 g01228580
2. Install relief valve (5). Install retaining ring (4).
Illustration 6 g03141720
3. Position manifold (2). Install bolts (1) and bolt (3).
End By:
a. Install the pump drive.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:49:00 UTC+0800 2019
3/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04954722
Accessory Drive (Transmission) - Remove and Install
SMCS - 1207-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
Illustration 1 g03140318
1. Remove bolts (1). Remove cover (2) and the O-ring seal.
1/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g03140345
Illustration 3 g03140420
2. Remove bolts (3) from adapter (4). Use bolts (3) to remove adapter (4).
Illustration 4 g03141316
3. Remove O-ring seal (5) and shims (6).
2/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 5 g03141378
4. Use Tooling (A) and a suitable press to remove bearing cup (7).
Illustration 6 g03141418
5. Remove gear assembly (8).
Illustration 7 g03141456
6. Remove bearing cones (9) and seal (10).
3/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 8 g03141469
7. Remove bearing cup (11).
Installation Procedure
Illustration 9 g03141517
1. Install bearing cup (11).
Illustration 10 g03141456
2. Raise the temperature of bearing cones (9) to install. Install seal (10).
4/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 11 g03141418
3. Install gear assembly (8).
Illustration 12 g03141540
4. Use Tooling (A) and suitable press to install bearing cup (7).
Illustration 13 g03141316
5. Install required shims (6) to obtain 0.1 mm (0.00394 inch) to 0.2 mm (0.00787 inch) end
play. Install O-ring seal (5) and lubricate with lubricant being sealed.
5/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 14 g03140345
6. Position adapter (4) and install bolts (3).
Illustration 15 g03140318
7. Position cover (2) and the O-ring seal. Install bolts (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:49:56 UTC+0800 2019
6/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04954150
Idler Gear (Transmission Accessory Drive) - Remove and
Install
SMCS - 1234-010
Removal Procedure
Start By:
a. Remove the pump drive.
Illustration 1 g03137780
1. Remove bolts (5) and remove cover and O-ring seal (4). Remove bolt (3) and washer (2).
2. Remove shaft (1) and remove idler gear (6) from the housing.
1/2
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g03139696
3. Remove bearing (7).
Installation Procedure
1. Install idler gear (6) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:50:51 UTC+0800 2019
2/2
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04947209
Pump Drive - Remove
SMCS - 3108-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
Start By:
a. Remove the torque converter housing.
Illustration 1 g03133076
1/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. 1. Attach Tooling (A) and a suitable lifting device to torque converter housing (1). The weight
of torque converter housing (1) is approximately 227 kg (500 lb). Position torque converter
housing (1) on to Tooling (B).
Illustration 2 g01231807
2. Remove bolts (2) and shield assembly (3).
Illustration 3 g03133357
3. Attach Tooling (A) and a suitable lifting device to pump drive (4). The weight of pump
drive (4) is approximately 32 kg (70 lb). Remove bolts (5) and (6). Remove pump drive (4).
Illustration 4 g03133457
2/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 4. Remove O-ring seals (7) from torque converter housing (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:51:47 UTC+0800 2019
3/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04947514
Pump Drive - Disassemble
SMCS - 3108-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
B
289-2838 Spanner 1
289-2846 Spline Wrench 1
C 8T-4184 Bolt 3
D -
Flat Stock Steel
1/16 - 3/4 by 8
2
Start By:
a. Remove the pump drive.
1/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g03133996
1. Remove ten bolts (1) and bolt (3). Remove manifold (2).
Illustration 2 g01231869
2. Use Tooling (A) in order to remove race (4) from manifold (2).
Illustration 3 g01231871
3. Remove carrier assembly (6) from manifold (5).
2/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...