This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and installing new seals is also covered. Dowels align the housing and bolts attach it to the cylinder block with specified torque.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes:
1) Removing the flywheel using a lifting device and removing bolts, then removing the flywheel ring gear if necessary.
2) Installing the flywheel ring gear if it was removed by heating it and positioning it on the flywheel, then installing the flywheel using bolts and a lifting device.
3) Removing the crankshaft rear seal by removing housing bolts and pulling out the seal, gasket and housing.
4) Installing the new crankshaft rear seal using a installer tool and pressing the seal
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...jskefksmemwe
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, and lifting the housing off using tooling. The installation procedure involves cleaning surfaces, aligning the housing on dowels, and installing mounting bolts with specified torques.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. The installation procedure describes cleaning the mating surfaces, attaching lifting tools to the housing, and reversing the removal steps to mount the housing back onto the engine. Torque specifications are provided for tightening the mounting bolts.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader powered by a 3054 engine. It describes the required tools and multi-step procedures, which include removing bolts, lifting components, cleaning parts, and tightening fasteners to the specified torques. The document contains illustrations supporting each step in the procedures.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader powered by a 3054 engine. It includes lists of required tools and step-by-step procedures with illustrations. The procedures describe removing the flywheel by lifting it off with a tool and removing the rear seal housing or one-piece assembly. Installation involves cleaning parts, pressing in the new seal, lubricating surfaces, and torquing bolts to specified values.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes:
1) Removing the flywheel using a lifting device and removing bolts, then removing the flywheel ring gear if necessary.
2) Installing the flywheel ring gear if it was removed by heating it and positioning it on the flywheel, then installing the flywheel using bolts and a lifting device.
3) Removing the crankshaft rear seal by removing housing bolts and pulling out the seal, gasket and housing.
4) Installing the new crankshaft rear seal using a installer tool and pressing the seal
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...jskefksmemwe
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, and lifting the housing off using tooling. The installation procedure involves cleaning surfaces, aligning the housing on dowels, and installing mounting bolts with specified torques.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. The installation procedure describes cleaning the mating surfaces, attaching lifting tools to the housing, and reversing the removal steps to mount the housing back onto the engine. Torque specifications are provided for tightening the mounting bolts.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader powered by a 3054 engine. It describes the required tools and multi-step procedures, which include removing bolts, lifting components, cleaning parts, and tightening fasteners to the specified torques. The document contains illustrations supporting each step in the procedures.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader powered by a 3054 engine. It includes lists of required tools and step-by-step procedures with illustrations. The procedures describe removing the flywheel by lifting it off with a tool and removing the rear seal housing or one-piece assembly. Installation involves cleaning parts, pressing in the new seal, lubricating surfaces, and torquing bolts to specified values.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes removal and installation procedures with lists of required tools and illustrations showing the step-by-step processes. The instructions cover both engines with a 14 bolt housing assembly and engines with a 10 bolt housing assembly.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and installing mounting bolts with specified torques.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and installing mounting bolts with specified torques.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing which include supporting the engine, removing mounting bolts from the top and sides, and lifting the housing off with lifting brackets. Reinstallation involves cleaning surfaces, placing the housing on the engine, and torquing the mounting bolts.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and installing mounting bolts with specified torques.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...jskefksmemwe
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and removing it from the cylinder block. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts to secure the housing. Tools required include link brackets for lifting.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fjjkskekfsxswamem
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe removing the flywheel by lifting it with a tool and removing bolts, and installing the flywheel by heating the ring gear, positioning the flywheel with a tool, and tightening bolts. Removing the rear seal involves taking off housing bolts and removing the seal, gasket and housing. Installing the rear seal includes pressing in the new seal, lubricating parts, and replacing the housing and bolts.
Caterpillar cat 426 c backhoe loader (prefix 1cr) service repair manual (1cr0...fjkekfmefmm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the cylinder block and flywheel housing mating surfaces before installation.
3) Installing the flywheel housing by placing it on the cylinder block and installing mounting bolts, taking care not to exceed the specified torque.
Caterpillar cat 426 c backhoe loader (prefix 1cr) service repair manual (1cr0...fjjsefkskemmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and illustrations showing the component locations. The removal procedure describes using a lifting device and removing bolts to take off the flywheel. The installation procedure explains heating the flywheel ring gear, positioning the flywheel and installing bolts with the specified torque. It also provides separate instructions for engines with 14-bolt or 10-bolt housings when removing and installing the crankshaft rear seal.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fujsjefjkskekfm
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, and reinstall the housing and gasket with bolts.
3) For engines with a 10 bolt housing, install the preassembled housing over the crankshaft until it contacts the cylinder block and centers it with a tool.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjufksefmme
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, lubricate parts, and position the housing and gasket on dowels before installing bolts.
3) For 10 bolt housings, place the pre-lubricated seal on the crankshaft and use a centering tool to align the housing before installing bolts.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjjskekksemmrt
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Removing mounting bolts from the top and sides of the flywheel housing and using lifting tools to remove the housing, which weighs approximately 70 lbs.
2) Cleaning the mating surfaces of the cylinder block and flywheel housing before installation. The instructions specify installing the housing by aligning it on the cylinder block and securing it with mounting bolts.
3) Recommendations to keep parts clean and contain fluids to prevent contamination or spills during the repair process.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjjsefkskemmm
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, lubricate parts, and position the housing and gasket on dowels before installing bolts.
3) For 10 bolt housings, place the pre-lubricated seal on the crankshaft and use a centering tool to align the housing before installing bolts.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader with a 3054 engine. It describes the required tools and multi-step processes which include removing bolts, lifting devices, cleaning parts, and torquing fasteners to the specified values. The document contains illustrations supporting each step of the procedures.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...fujskkmdmd
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and rear crankshaft seal. Detailed illustrations and cautions are provided for each step. The process involves drilling holes in the crankshaft rear seal before removing it, cleaning and applying compounds to mating surfaces, and checking dowel pins and gaskets before reassembly.
More Related Content
Similar to Caterpillar Cat 416C Backhoe Loader (Prefix 1WR) Service Repair Manual (1WR08116-10736).pdf
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes removal and installation procedures with lists of required tools and illustrations showing the step-by-step processes. The instructions cover both engines with a 14 bolt housing assembly and engines with a 10 bolt housing assembly.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and installing mounting bolts with specified torques.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and installing mounting bolts with specified torques.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing which include supporting the engine, removing mounting bolts from the top and sides, and lifting the housing off with lifting brackets. Reinstallation involves cleaning surfaces, placing the housing on the engine, and torquing the mounting bolts.
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe using lifting devices and installer tools to remove and position the heavy flywheel and housing assembly, as well as cleaning, lubricating, and torquing components to the specified values.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and installing mounting bolts with specified torques.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...jskefksmemwe
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and removing it from the cylinder block. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts to secure the housing. Tools required include link brackets for lifting.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fjjkskekfsxswamem
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe removing the flywheel by lifting it with a tool and removing bolts, and installing the flywheel by heating the ring gear, positioning the flywheel with a tool, and tightening bolts. Removing the rear seal involves taking off housing bolts and removing the seal, gasket and housing. Installing the rear seal includes pressing in the new seal, lubricating parts, and replacing the housing and bolts.
Caterpillar cat 426 c backhoe loader (prefix 1cr) service repair manual (1cr0...fjkekfmefmm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Removing mounting bolts from the top and rear of the flywheel housing and using lifting tools to remove the housing.
2) Cleaning the cylinder block and flywheel housing mating surfaces before installation.
3) Installing the flywheel housing by placing it on the cylinder block and installing mounting bolts, taking care not to exceed the specified torque.
Caterpillar cat 426 c backhoe loader (prefix 1cr) service repair manual (1cr0...fjjsefkskemmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and illustrations showing the component locations. The removal procedure describes using a lifting device and removing bolts to take off the flywheel. The installation procedure explains heating the flywheel ring gear, positioning the flywheel and installing bolts with the specified torque. It also provides separate instructions for engines with 14-bolt or 10-bolt housings when removing and installing the crankshaft rear seal.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fujsjefjkskekfm
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, and reinstall the housing and gasket with bolts.
3) For engines with a 10 bolt housing, install the preassembled housing over the crankshaft until it contacts the cylinder block and centers it with a tool.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjufksefmme
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, lubricate parts, and position the housing and gasket on dowels before installing bolts.
3) For 10 bolt housings, place the pre-lubricated seal on the crankshaft and use a centering tool to align the housing before installing bolts.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjjskekksemmrt
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Removing mounting bolts from the top and sides of the flywheel housing and using lifting tools to remove the housing, which weighs approximately 70 lbs.
2) Cleaning the mating surfaces of the cylinder block and flywheel housing before installation. The instructions specify installing the housing by aligning it on the cylinder block and securing it with mounting bolts.
3) Recommendations to keep parts clean and contain fluids to prevent contamination or spills during the repair process.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjjsefkskemmm
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, lubricate parts, and position the housing and gasket on dowels before installing bolts.
3) For 10 bolt housings, place the pre-lubricated seal on the crankshaft and use a centering tool to align the housing before installing bolts.
Similar to Caterpillar Cat 416C Backhoe Loader (Prefix 1WR) Service Repair Manual (1WR08116-10736).pdf (19)
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader with a 3054 engine. It describes the required tools and multi-step processes which include removing bolts, lifting devices, cleaning parts, and torquing fasteners to the specified values. The document contains illustrations supporting each step of the procedures.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...fujskkmdmd
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and rear crankshaft seal. Detailed illustrations and cautions are provided for each step. The process involves drilling holes in the crankshaft rear seal before removing it, cleaning and applying compounds to mating surfaces, and checking dowel pins and gaskets before reassembly.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and reinstalling the mounting bolts. Tools including link brackets and lifting devices are required.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The procedure involves using a drill bit to drill out the plastic sleeve holding the seal in place. Once drilled out, the seal can be removed from the front cover housing. Proper cleaning of parts and containment of fluids is emphasized to prevent contamination.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...fujskkmdmd
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and clamps, and disconnecting tubes and hoses to remove the cylinder head.
3. Installing a new gasket and torquing bolts to specified values to install the cylinder head. Reconnecting all tubes, hoses and harness assemblies.
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover by loosening the clamp.
3. Removing the bolts securing the regulator housing and removing the regulator from the engine.
The instructions emphasize cleanliness and safe handling of fluids during maintenance.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...fujskkmdmd
The document provides instructions for removing and installing a unit injector hydraulic pump on a 322C FM EXCAVATOR C3R powered by a 3126B engine. The removal procedure involves disconnecting hoses and lines, removing bolts, and taking off the pump. The installation procedure specifies lubricating seals, installing bolts, reconnecting lines and hoses, and ensuring connections are secure. Separate sections provide instructions for disassembling and assembling a turbocharger on the same engine model.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual (BPH0000...fujskkmdmd
This document provides instructions for removing and installing a governor from a 322C FM EXCAVATOR engine. It describes disconnecting linkages, removing mounting bolts and clips, and using special tools. Proper cleaning and lubrication of seals is emphasized. References are provided for additional information on governor inspection and testing procedures.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual (CAM0000...fujskkmdmd
The document provides instructions for removing the engine oil filter base from a 322C FM excavator. The procedure involves first removing the turbocharger. Then, using a strap wrench, loosen the oil filter base by turning it counterclockwise. Finally, clean the mating surface before installing the new oil filter base. The summary is provided in 3 sentences or less as requested.
Caterpillar Cat 320D L Excavator (Prefix KLM) Service Repair Manual (KLM00001...fujskkmdmd
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure involves using a slide hammer puller to remove the existing seal after drilling holes in it. For installation, a front seal installer tool is used to carefully push the new seal onto the crankshaft flange. Proper cleaning and containment of fluids is emphasized.
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and rear crankshaft seal. Detailed illustrations and cautions are provided for each step. The process involves drilling holes in the crankshaft rear seal before removing it, cleaning and applying compounds to mating surfaces, and checking dowel pins and gaskets before reassembly.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix EC2) Service Repair ...fujskkmdmd
This document provides instructions for removing and installing various engine components on a Caterpillar 308E2CR Mini Hydraulic Excavator, including the fuel injection pump, electronic unit injectors, turbocharger, and mass air flow pressure sensor. The procedures describe using required tools, disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components in the reverse order while applying specified torques. Safety notices warn technicians to allow the fuel system to purge before opening lines and ensure components like the mass air flow sensor are oriented correctly.
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...fujskkmdmd
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
This document provides instructions for removing the crankshaft front seal from a Caterpillar C6.4 engine. The procedure involves using a slide hammer puller tool to remove the seal from the front of the crankshaft. Technicians are advised to keep all parts clean and contain fluids properly during repair work. Removal of the seal prepares the engine for further disassembly or repair of crankshaft components.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fujskkmdmd
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...fujskkmdmd
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal, wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures include using various tools to remove components, cleaning parts, applying sealant or oil, and torquing bolts to the specified values. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix W8S) Service Repair ...fujskkmdmd
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator, including:
- Removing and installing the diesel particulate filter.
- Removing and installing the inlet manifold.
- Removing and installing the inlet and exhaust valve springs.
- Removing and installing the inlet and exhaust valves.
Detailed step-by-step instructions are provided along with illustrations to correctly complete each procedure. Safety precautions and notes are included throughout.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix TMX) Service Repair ...fujskkmdmd
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator including the crankshaft front seal, idler gear, housing (front), valve mechanism cover, bridge dowels, rocker shaft and push rod. The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Safety and installation notes are also provided.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1WR
Configuration: 416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406238
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00546794
Typical Example. Different lifting device shown than what is called out in the Table.
Illustration 2 g00546793
1. Install Tool (A) and a suitable lifting device on flywheel (1) .
2. Remove bolts (3) and bearing housing (4) .
3. Remove six bolts (2) and the washers from the flywheel.
Note: The 3054 and 3056 marine engines used several bolt patterns to attach the flywheel to
the crankshaft. There are drilled holes that are not used in the crankshaft and in the
flywheel.
4. Use the suitable lifting device in order to remove flywheel (1) . The weight of flywheel (1)
and the flywheel ring gear is 53 kg (120 lb).
5. If removal of the flywheel ring gear is necessary, place an index mark on the chamfer of the
flywheel ring gear for the installation process.
Illustration 3 g00546795
2/3
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. 6. Use a hammer and a punch in order to remove flywheel ring gear (5) from flywheel (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 1 16:38:10 UTC+0800 2020
3/3
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1WR
Configuration: 416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406239
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Always wear protective gloves when handling parts that have been
heated.
1/2
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 1 g00803517
Typical Example. Different Lifting device shown than what is called out in the table.
1. If flywheel ring gear (5) was removed, heat flywheel ring gear (5) to a temperature of 250 °
C (480 °F).
Note: Do not use a torch to heat the flywheel ring gear.
2. Install flywheel ring gear (5) on flywheel (1) .
Note: Ensure that the chamfer of the flywheel ring gear is in the correct position on the
flywheel.
3. Install Tool (A) and a suitable lifting device on flywheel (1) and position flywheel (1) in the
flywheel housing. The weight of flywheel (1) and flywheel ring gear (5) is 53 kg (120 lb).
Illustration 2 g00546793
4. Install six bolts (2) and the washers that hold flywheel (1) in position. Tighten the bolts to a
torque of 105 N·m (77 lb ft).
5. Put bearing housing (4) in position on the flywheel. Install four bolts (3) that fasten bearing
housing (4) to the flywheel.
6. Refer to the Specifications Module, "Flywheel" topic for information on inspecting the
flywheel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 1 16:39:07 UTC+0800 2020
2/2
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1WR
Configuration: 416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741403
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Engines with 14 Bolt Housing Assembly
Illustration 1 g00632744
The flywheel housing has been removed for photographic purposes only.
1. Remove bolts (1) from housing (3).
2. Remove socket head bolts (2) from housing (3).
3. Remove the crankshaft rear seal, the gasket, and housing (3) from the dowels in the cylinder
block.
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
Illustration 2 g00830867
2/3
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. 1. Remove the bolts in reverse order of the numbered sequence. Refer to Illustration 2.
2. Remove the one-piece housing assembly from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 1 16:40:04 UTC+0800 2020
3/3
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1WR
Configuration: 416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01605362
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6205 Rear Seal Installer 1
1P-0510 Driver Group 1
B FT-2806 Alignment Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engines with 14 Bolt Housing Assembly
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Clean the areas of the parts that will contact each other.
1/4
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 1 g00541839
3. Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make
sure that you install the seal to the correct depth in the housing. Refer to Specifications,
"Crankshaft Seals" for additional information.
4. Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
5. Install Tool (A) onto the crankshaft flange.
6. Put the new gasket for the housing in position on the dowels in the cylinder block.
Illustration 2 g00606404
7. Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
8. Position housing (3) on the dowels in the cylinder block.
9. Remove Tool (A) .
2/4
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 3 g00606340
The flywheel housing has been removed for photographic purposes only.
10. Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
11. Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
1. Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and
dirt.
Illustration 4 g00831176
3/4
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the
crankshaft flange before installation.
2. Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the
cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the
plastic sleeve after the housing assembly is installed.
3. Place Tool (B) over housing assembly (3). This will center the housing assembly onto the
crankshaft flange.
Illustration 5 g00830867
4. Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the
cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
5. Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 1 16:41:01 UTC+0800 2020
4/4
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1WR
Configuration: 416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741450
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Support the engine with blocks or with a suitable lifting device on a flat level surface.
Illustration 1 g00541891
Typical example
2. Remove mounting bolts (1) from the top of flywheel housing (2).
Illustration 2 g00541892
Typical example
3. Attach Tooling (A) and a suitable lifting device to flywheel housing (2).
4. Remove mounting bolts (3) that attach the flywheel housing to the cylinder block.
2/4
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 5. Remove flywheel housing (2). If necessary, hit flywheel housing (2) with a soft faced
hammer in order to separate flywheel housing (2) from the cylinder block. The weight of
flywheel housing (2) is approximately 32 kg (70 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing.
Inspect the felt seal on the rear flange of the engine oil pan. Replace the felt seal, if
necessary. Inspect the dowels in the cylinder block that align the flywheel housing. Replace
the dowels, if necessary.
Illustration 3 g00541892
2. Use Tooling (A) and a suitable lifting device to position flywheel housing (2) on the dowels
that are on the cylinder block. The weight of flywheel housing (2) is approximately 32 kg
(70 lb).
3. Install mounting bolts (3).
3/4
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. Illustration 4 g00541891
Typical example
4. Install mounting bolts (1) that attach flywheel housing (2) to the cylinder block.
Tighten the bolts for an aluminum flywheel housing to a torque of 70 N·m (52 lb ft).
Tighten the cast iron flywheel housing bolts to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
5. Remove Tooling (A) from the flywheel housing.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 1 16:41:57 UTC+0800 2020
4/4
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1WR
Configuration: 416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01461242
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
A. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Illustration 1 g00553762
Typical example
1. Remove three bolts (2) that hold thrust block (3) in position.
2. Remove thrust block (3) from the end of the crankshaft. The thrust block holds the
crankshaft pulley in position on the end of the crankshaft.
3. Remove crankshaft pulley (1) from the engine.
1/2
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Note: Some engines have a water immersion seal that is placed on the front cover. The seal has a
flexible lip on the front. The plastic mandrel that is supplied with the seal must be installed in the
seal when the crankshaft pulley is removed. This will ensure that the lip maintains the correct
shape.
Installation Procedure
Illustration 2 g00553762
Typical example
1. Remove the plastic mandrel, if necessary.
2. Put crankshaft pulley (1) in position on the crankshaft.
3. Apply 9S-3263 Thread Lock Compound to the threads of three bolts (2) .
4. Put thrust block (3) in position and align the holes with the holes in the end of the
crankshaft.
Note: It may be necessary to keep the crankshaft from rotating while you torque bolts (3).
Use the appropriate tools in order to keep the crankshaft from rotating.
5. Install three bolts (2) that hold the thrust block in position. Tighten bolts (2) to a torque of
115 N·m (85 lb ft).
End By: Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 1 16:42:54 UTC+0800 2020
2/2
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416C BACKHOE LOADER 1WR
Configuration: 416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01742537
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit 1
B 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
416C Backhoe Loader 1WR08116-10736 (MACHINE) POWERED BY 3054 Engine(...
2020/1/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...