The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing components like the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The procedures describe the required tools and parts, safety precautions, step-by-step instructions, and torque specifications. Illustrations are provided to supplement the written instructions.
The document provides instructions for removing and installing components of the torque converter housing and pump drive on a Caterpillar 730C2 articulated truck. The removal procedure includes using lifting devices and tools to detach the torque converter housing and pump drive. Components like bolts, seals and manifolds are then removed from the housing and drive.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck. The instructions include removing the torque converter housing, pump drive, accessory drive, idler gear, and relief valve. Tools required are listed, along with torque specifications and other details needed to correctly complete the disassembly and reassembly procedures.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck powered by a C13 engine. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck powered by a C13 engine. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing components of the torque converter housing and pump drive on a Caterpillar 730C2 articulated truck. The removal procedure includes using lifting devices and tools to detach the torque converter housing and pump drive. Components like bolts, seals and manifolds are then removed from the housing and drive.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck. The instructions include removing the torque converter housing, pump drive, accessory drive, idler gear, and relief valve. Tools required are listed, along with torque specifications and other details needed to correctly complete the disassembly and reassembly procedures.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck powered by a C13 engine. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck powered by a C13 engine. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck powered by a C13 engine. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck powered by a C13 engine. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The pump drive removal procedure involves detaching the torque converter housing and shield assembly, then removing bolts and the pump drive unit. The pump drive disassembly requires removing manifold bolts and parts, races, and the carrier assembly.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The pump drive removal procedure involves detaching the torque converter housing and shield assembly, then removing bolts and the pump drive unit. The pump drive disassembly requires removing manifold bolts and parts, races, and the carrier assembly.
The document provides instructions for removing and installing various transmission components on a 730C2 articulated truck, including:
1. Removing and installing a torque converter housing, which requires attaching lifting tools and brackets due to the housing's 500 lb weight.
2. Removing and installing a relief valve on the torque converter inlet, which involves removing a manifold, relief valve, and O-ring seal.
3. Removing and installing an accessory drive on the transmission, which requires pressing out and installing bearing cups and removing/installing gears, seals, and shims.
4. Removing and installing an idler gear on the transmission accessory drive, which removes the gear from the housing.
5
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure lists 11 steps to remove the rear gear group which includes removing bolts, seals, gears, bushings and bearings. The installation procedure provides 12 steps and specifies tools and torque specifications to install the components in reverse order. A separate section provides procedures for removing and installing the flywheel, which includes using lifting equipment and installing with loctite and torqueing bolts to the specified value.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings and covers. The installation procedure provides steps to install these components in reverse order and includes cleaning and applying threadlocker to bolts. Tools required are also listed.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. The installation procedure provides steps to install the rear crankshaft seal, gears, covers and flywheel in the reverse order of removal. Tools required are also listed.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck powered by a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, bearings, and covers. The installation procedure provides instructions on cleaning parts, applying threadlocker, installing bearings at the proper temperature and orientation, and torquing bolts in a specific sequence. Precautions are included to handle parts safely and contain fluids.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C13 engine, including:
- Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
- Installing the rear gear group by lowering temperatures of bearings, installing seals, gears, bushings, and bearings within specified dimensions, and torquing bolts.
- Removing the flywheel by attaching lifting tools and removing bolts.
- Installing the flywheel by heating and seating the ring gear, attaching lifting tools, installing bolts with threadlocker, and checking runout.
- Removing
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on an EL300 Excavator. The procedures include removing bolts, disconnecting tubes, and removing parts while taking precautions to contain fluids. Reinstallation involves cleaning parts, applying new gaskets or seals if needed, and reconnecting tubes before turning fuel valves back on. The fuel transfer pump section also provides instructions for disassembling and assembling the pump components.
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It outlines 22 steps for disassembly, including removing covers, plates, gears, and other components. It then outlines 45 steps for assembly, describing how to clean parts, install bearings and seals, measure clearances, and reassemble the gears, carriers, rings, and other parts in the reverse order of disassembly. The goal is to properly disassemble, measure, and reassemble the travel drive components.
Caterpillar Cat D4E TRACK-TYPE TRACTOR (Prefix 77W) Service Repair Manual.pdfzhaowo17360
The document provides instructions for disassembling and assembling an alternator. It describes removing components like the regulator, capacitor, pulley, fan, screws holding frames, rotor, bearings, slip ring, terminals, and stator. It then describes assembling these components in reverse order, making sure parts are clean and replacing any worn parts. The instructions are detailed with illustrations showing each step.
Caterpillar Cat D4E TRACK TRACTOR Service Repair Manual (77W01664 and UP).pdfzhaowo17360
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3304B or 3306B engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing bolts and disconnecting tubes. Reinstallation involves installing gaskets and bolts and turning the fuel supply back on.
- Removing the fuel filter base by using a strap wrench to remove the fuel filter, disconnecting fuel lines, and removing bolts and gaskets. Reinstallation involves installing new gaskets if needed and bolts.
- Procedures for removing the fuel transfer pump, which involves disconnecting fuel lines and electrical connections and removing mounting bolts.
More Related Content
Similar to Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2T400001 and up).pdf
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck powered by a C13 engine. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck powered by a C13 engine. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The pump drive removal procedure involves detaching the torque converter housing and shield assembly, then removing bolts and the pump drive unit. The pump drive disassembly requires removing manifold bolts and parts, races, and the carrier assembly.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The pump drive removal procedure involves detaching the torque converter housing and shield assembly, then removing bolts and the pump drive unit. The pump drive disassembly requires removing manifold bolts and parts, races, and the carrier assembly.
The document provides instructions for removing and installing various transmission components on a 730C2 articulated truck, including:
1. Removing and installing a torque converter housing, which requires attaching lifting tools and brackets due to the housing's 500 lb weight.
2. Removing and installing a relief valve on the torque converter inlet, which involves removing a manifold, relief valve, and O-ring seal.
3. Removing and installing an accessory drive on the transmission, which requires pressing out and installing bearing cups and removing/installing gears, seals, and shims.
4. Removing and installing an idler gear on the transmission accessory drive, which removes the gear from the housing.
5
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure lists 11 steps to remove the rear gear group which includes removing bolts, seals, gears, bushings and bearings. The installation procedure provides 12 steps and specifies tools and torque specifications to install the components in reverse order. A separate section provides procedures for removing and installing the flywheel, which includes using lifting equipment and installing with loctite and torqueing bolts to the specified value.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings and covers. The installation procedure provides steps to install these components in reverse order and includes cleaning and applying threadlocker to bolts. Tools required are also listed.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730C2 Ejector Articulated Truck powered by a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. The installation procedure provides steps to install the rear crankshaft seal, gears, covers and flywheel in the reverse order of removal. Tools required are also listed.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 730 articulated truck powered by a C13 engine. The removal procedure involves using various tools to remove bolts, seals, gears, bearings, and covers. The installation procedure provides instructions on cleaning parts, applying threadlocker, installing bearings at the proper temperature and orientation, and torquing bolts in a specific sequence. Precautions are included to handle parts safely and contain fluids.
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar C13 engine, including:
- Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
- Installing the rear gear group by lowering temperatures of bearings, installing seals, gears, bushings, and bearings within specified dimensions, and torquing bolts.
- Removing the flywheel by attaching lifting tools and removing bolts.
- Installing the flywheel by heating and seating the ring gear, attaching lifting tools, installing bolts with threadlocker, and checking runout.
- Removing
Similar to Caterpillar Cat 730C2 Articulated Truck (Prefix 2T4) Service Repair Manual (2T400001 and up).pdf (14)
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on an EL300 Excavator. The procedures include removing bolts, disconnecting tubes, and removing parts while taking precautions to contain fluids. Reinstallation involves cleaning parts, applying new gaskets or seals if needed, and reconnecting tubes before turning fuel valves back on. The fuel transfer pump section also provides instructions for disassembling and assembling the pump components.
This document provides instructions for disassembling and assembling the travel drives of an E120B excavator. It outlines 22 steps for disassembly, including removing covers, plates, gears, and other components. It then outlines 45 steps for assembly, describing how to clean parts, install bearings and seals, measure clearances, and reassemble the gears, carriers, rings, and other parts in the reverse order of disassembly. The goal is to properly disassemble, measure, and reassemble the travel drive components.
Caterpillar Cat D4E TRACK-TYPE TRACTOR (Prefix 77W) Service Repair Manual.pdfzhaowo17360
The document provides instructions for disassembling and assembling an alternator. It describes removing components like the regulator, capacitor, pulley, fan, screws holding frames, rotor, bearings, slip ring, terminals, and stator. It then describes assembling these components in reverse order, making sure parts are clean and replacing any worn parts. The instructions are detailed with illustrations showing each step.
Caterpillar Cat D4E TRACK TRACTOR Service Repair Manual (77W01664 and UP).pdfzhaowo17360
The document provides instructions for removing and installing various fuel system components on a Caterpillar 3304B or 3306B engine, including:
- Removing the fuel priming pump by turning off the fuel supply, removing bolts and disconnecting tubes. Reinstallation involves installing gaskets and bolts and turning the fuel supply back on.
- Removing the fuel filter base by using a strap wrench to remove the fuel filter, disconnecting fuel lines, and removing bolts and gaskets. Reinstallation involves installing new gaskets if needed and bolts.
- Procedures for removing the fuel transfer pump, which involves disconnecting fuel lines and electrical connections and removing mounting bolts.
The document provides instructions for removing and installing the fuel priming pump on a Caterpillar D4E track-type tractor. It lists the required tools and safety precautions before describing the removal process which involves turning off the fuel supply, removing securing bolts and hoses. The installation process is then described and involves reversing the removal steps and ensuring new gaskets are used if old ones are damaged.
The document provides instructions for removing and installing various fuel system components on a Caterpillar D4E track-type tractor powered by a 3304 engine. The components include the fuel priming pump, fuel filter base, and fuel transfer pump. Removal involves disconnecting connecting lines, removing mounting bolts and base, and taking note of gasket condition. Installation is the reverse of removal and includes checking and replacing worn gaskets. Disassembly of the fuel transfer pump is also described through removal of springs, seals, valves, piston, and housing pieces.
The document provides instructions for removing and installing the fuel injection pump housing and governor on a Caterpillar 3304B or 3306B engine. The removal procedure involves disconnecting fuel lines and other components, removing mounting bolts and nuts, and lifting the housing and governor off the engine using two technicians or a lifting device. The installation procedure specifies cleaning and lubricating parts, inserting components in the correct order, and using tools to set timing and clearances.
This document provides instructions for removing and installing various components of a C32 Locomotive Engine, including:
1) The exhaust gas valve, involving removing seals, spools, and other parts before reassembly.
2) The exhaust elbow, requiring loosening clamps, sliding parts, and installing new components.
3) The catalyst, which is removed using lifting straps and reinstalled by aligning marks.
4) The air inlet elbow, involving disconnecting tubes, removing bolts, and replacing seals during reinstallation.
5) The inlet manifold, requiring removing brackets, clamps, and bolts before reversing the process to reinstall.
This document provides instructions for removing and installing fuel system components on a C32 Industrial Engine, including:
- Removing and installing nonmetallic fuel lines, noting best practices like proper hose length and avoiding contact with other surfaces.
- Removing the fuel filter and water separator, disconnecting hoses and electrical connections, and installing a new filter.
- Removing the fuel transfer pump by disconnecting hoses and removing mounting bolts, and installing the pump with a new O-ring seal.
The document provides instructions for removing and installing various fuel system components on a C32 Industrial Engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel lines
- Fuel transfer pump
- Fuel pressure regulator
The procedures include disconnecting fuel lines and electrical connections, removing mounting hardware, and installing components in reverse order. Proper torque specifications and safety precautions are listed for each component. Best practices are also outlined for installing nonmetallic fuel lines to prevent damage.
This document provides instructions for removing and installing fuel system components on a C32 Industrial Engine BT4, including:
- The fuel priming pump, fuel filter base, fuel transfer pump, and various fuel lines. Detailed step-by-step removal and installation procedures are provided along with required tools. Best practices are outlined for properly installing nonmetallic fuel lines.
- The document provides instructions for removing and installing inlet and exhaust valves on a 3054E Industrial Engine.
- Key steps include using a valve spring compressor tool to compress the valve spring, removing the valve keepers and spring retainer, and then removing the valve stem seal and valve.
- Installation involves cleaning parts, lubricating the valve stems, and installing the valves along with new stem seals, springs, retainers and keepers using the compressor tool. Taking care with spring loaded parts is emphasized for safety.
This document provides instructions for installing and removing a fuel injection pump on an industrial engine. It outlines the required tools and parts. The procedure describes checking the O-ring seal on the pump, lubricating it with oil, and installing the pump on the engine, ensuring proper timing. It notes to install a timing pin to check timing and remove any backlash in the gears. Finally, it describes installing fuel lines and the water pump once the fuel injection pump is installed.
This document provides instructions for removing and installing components on a Caterpillar 973C track loader engine, including:
- Removing and installing the turbocharger
- Removing and installing the exhaust manifold
- Removing and installing the air inlet heater
The instructions include lists of required tools and step-by-step procedures with illustrations. Safety notices are provided regarding keeping parts clean, containing fluids, and wearing protective equipment when working on the engine.
This document provides instructions for removing and installing the hydrostatic drive oil tank from a 973C track loader. It describes disconnecting hoses and removing mounting bolts to detach the tank. Proper care is advised when handling fluids. The installation process reverses the removal steps and includes reconnecting hoses and refilling the tank. Additional sections provide instructions for disassembling the pump drive unit.
The document provides instructions for removing and installing various components of a 963K track loader, including:
- Releasing hydraulic system pressure before removing any components or lines.
- Removing the ripper by detaching lift cylinders, removing bolts and pins, and lifting it off with a tool.
- Removing the ripper lift cylinder by disconnecting hoses and tubes, removing bolts and pins, and lifting it out.
- Removing the bucket by lowering the lift arm, releasing pressure, removing pins and bolts, and lifting the bucket off.
It outlines the required tools and provides step-by-step instructions for removing and installing each component safely.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i07526804
Torque Converter Housing - Install
SMCS - 3105-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B - Loctite 242 -
C 385-4000 Seal Installation Tool 1
D - Loctite Flange Sealant 5900 -
Illustration 1 g03129265
1. Install studs (9) if removed. Install seal (8).
1/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g03129058
Illustration 3 g03129157
2. Attach Tooling (A) and a suitable lifting device to torque converter housing. The weight of
torque converter housing (5) is approximately 227 kg (500 lb). Install torque converter
housing (5).
3. Apply Tooling (D) to the housing spotface and washer of bolt (7).
Note: Remove excess sealant after bolt (7) is torqued.
4. Install bolt (7). Apply Tooling (B) to the threads of studs (9). Install nuts (6). Tighten bolt
(7) and nuts (6) to a torque of 100 ± 20 N·m (74 ± 15 lb ft).
2/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g03129025
5. Connect harness assembly and cable strap (4).
Illustration 5 g03129017
6. Connect harness assembly (2) and cable straps (3).
Illustration 6 g03128943
7. Use Tooling (C) and Install lip seal (1) dry.
End By:
a. Install the gear pump (scavenge transmission).
b. Install the torque converter.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:48:04 UTC+0800 2019
3/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04947892
Relief Valve (Torque Converter Inlet) - Remove and Install
SMCS - 3133-010-OL
Removal Procedure
Start By:
a. Remove the pump drive.
Illustration 1 g03141720
1. Remove bolts (1) and bolt (3). Remove manifold (2).
1/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 5 g01228580
2. Install relief valve (5). Install retaining ring (4).
Illustration 6 g03141720
3. Position manifold (2). Install bolts (1) and bolt (3).
End By:
a. Install the pump drive.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:49:00 UTC+0800 2019
3/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04954722
Accessory Drive (Transmission) - Remove and Install
SMCS - 1207-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
Illustration 1 g03140318
1. Remove bolts (1). Remove cover (2) and the O-ring seal.
1/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g03140345
Illustration 3 g03140420
2. Remove bolts (3) from adapter (4). Use bolts (3) to remove adapter (4).
Illustration 4 g03141316
3. Remove O-ring seal (5) and shims (6).
2/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 5 g03141378
4. Use Tooling (A) and a suitable press to remove bearing cup (7).
Illustration 6 g03141418
5. Remove gear assembly (8).
Illustration 7 g03141456
6. Remove bearing cones (9) and seal (10).
3/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 8 g03141469
7. Remove bearing cup (11).
Installation Procedure
Illustration 9 g03141517
1. Install bearing cup (11).
Illustration 10 g03141456
2. Raise the temperature of bearing cones (9) to install. Install seal (10).
4/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 11 g03141418
3. Install gear assembly (8).
Illustration 12 g03141540
4. Use Tooling (A) and suitable press to install bearing cup (7).
Illustration 13 g03141316
5. Install required shims (6) to obtain 0.1 mm (0.00394 inch) to 0.2 mm (0.00787 inch) end
play. Install O-ring seal (5) and lubricate with lubricant being sealed.
5/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 14 g03140345
6. Position adapter (4) and install bolts (3).
Illustration 15 g03140318
7. Position cover (2) and the O-ring seal. Install bolts (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:49:56 UTC+0800 2019
6/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04954150
Idler Gear (Transmission Accessory Drive) - Remove and
Install
SMCS - 1234-010
Removal Procedure
Start By:
a. Remove the pump drive.
Illustration 1 g03137780
1. Remove bolts (5) and remove cover and O-ring seal (4). Remove bolt (3) and washer (2).
2. Remove shaft (1) and remove idler gear (6) from the housing.
1/2
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g03139696
3. Remove bearing (7).
Installation Procedure
1. Install idler gear (6) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:50:51 UTC+0800 2019
2/2
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04947209
Pump Drive - Remove
SMCS - 3108-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-2420 Transmission Repair Stand 1
Start By:
a. Remove the torque converter housing.
Illustration 1 g03133076
1/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. 1. Attach Tooling (A) and a suitable lifting device to torque converter housing (1). The weight
of torque converter housing (1) is approximately 227 kg (500 lb). Position torque converter
housing (1) on to Tooling (B).
Illustration 2 g01231807
2. Remove bolts (2) and shield assembly (3).
Illustration 3 g03133357
3. Attach Tooling (A) and a suitable lifting device to pump drive (4). The weight of pump
drive (4) is approximately 32 kg (70 lb). Remove bolts (5) and (6). Remove pump drive (4).
Illustration 4 g03133457
2/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 4. Remove O-ring seals (7) from torque converter housing (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 28 10:51:47 UTC+0800 2019
3/3
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 730C2 ARTICULATED TRUCK 2T4
Configuration: 730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C2 and 725C2 Articulated Truck Power Train
Media Number -M0069866-02 Publication Date -01/10/2014 Date Updated -14/11/2016
i04947514
Pump Drive - Disassemble
SMCS - 3108-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
B
289-2838 Spanner 1
289-2846 Spline Wrench 1
C 8T-4184 Bolt 3
D -
Flat Stock Steel
1/16 - 3/4 by 8
2
Start By:
a. Remove the pump drive.
1/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g03133996
1. Remove ten bolts (1) and bolt (3). Remove manifold (2).
Illustration 2 g01231869
2. Use Tooling (A) in order to remove race (4) from manifold (2).
Illustration 3 g01231871
3. Remove carrier assembly (6) from manifold (5).
2/6
730C2 Articulated Truck 2T400001-UP (MACHINE) POWERED BY C13 Engine(M...
2019/12/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...