The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal, wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures include using various tools to remove components, cleaning parts, applying sealant or oil, and torquing bolts to the specified values. Safety notices are provided to keep parts clean and contain fluids during maintenance.
Caterpillar cat 308 e mini hydraulic excavator (prefix taz) service repair ma...fjjsekfksmem
The document provides instructions for servicing components of a 308E Mini Hydraulic Excavator powered by a C3.3B engine, including:
1) Removing and installing the crankshaft rear seal, wear sleeve, and gear.
2) Removing and installing the flywheel housing.
3) Removing and installing the crankshaft pulley.
4) Removing and installing the crankshaft front seal.
5) Checking the alignment of timing marks on gears.
The instructions include diagrams illustrating the components and procedures. Technicians are advised to keep parts clean, contain fluids, and refer to specification documents for torque values.
Caterpillar cat 308 e mini hydraulic excavator (prefix taz) service repair ma...fujsjekskem
The document provides instructions for servicing components of a 308E Mini Hydraulic Excavator powered by a C3.3B engine, including:
1) Removing and installing the crankshaft rear seal, wear sleeve, and gear.
2) Removing and installing the flywheel housing.
3) Removing and installing the crankshaft pulley.
4) Removing and installing the crankshaft front seal.
5) Checking the alignment of timing marks on gears.
The procedures provide detailed steps and illustrations for each component. Cautions are included to keep parts clean and contain fluids.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...hvy7sbkw8e
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures include using various tools to remove components, cleaning parts, applying sealant or oil, and torquing bolts to the specified values. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...xiapokang564341
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures include using various tools and following steps such as removing bolts, checking alignments, cleaning parts, and lubricating surfaces. Torque specifications and safety notices are also provided.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...wenxian17880
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures include using various tools and following steps such as removing bolts, seals, and gears in the specified order and installing components by reversing the removal process. Precautions are outlined such as keeping parts clean and containing fluids.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...fjjskekskem
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. The components include the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications. Safety notices are also included to keep parts clean and contain fluids properly.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...fhshefjjskefkem
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...fujsjefskekfksem
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 308 e mini hydraulic excavator (prefix taz) service repair ma...fjjsekfksmem
The document provides instructions for servicing components of a 308E Mini Hydraulic Excavator powered by a C3.3B engine, including:
1) Removing and installing the crankshaft rear seal, wear sleeve, and gear.
2) Removing and installing the flywheel housing.
3) Removing and installing the crankshaft pulley.
4) Removing and installing the crankshaft front seal.
5) Checking the alignment of timing marks on gears.
The instructions include diagrams illustrating the components and procedures. Technicians are advised to keep parts clean, contain fluids, and refer to specification documents for torque values.
Caterpillar cat 308 e mini hydraulic excavator (prefix taz) service repair ma...fujsjekskem
The document provides instructions for servicing components of a 308E Mini Hydraulic Excavator powered by a C3.3B engine, including:
1) Removing and installing the crankshaft rear seal, wear sleeve, and gear.
2) Removing and installing the flywheel housing.
3) Removing and installing the crankshaft pulley.
4) Removing and installing the crankshaft front seal.
5) Checking the alignment of timing marks on gears.
The procedures provide detailed steps and illustrations for each component. Cautions are included to keep parts clean and contain fluids.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...hvy7sbkw8e
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures include using various tools to remove components, cleaning parts, applying sealant or oil, and torquing bolts to the specified values. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...xiapokang564341
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures include using various tools and following steps such as removing bolts, checking alignments, cleaning parts, and lubricating surfaces. Torque specifications and safety notices are also provided.
Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Man...wenxian17880
The document provides instructions for removing and installing various engine components on a 308E Mini Hydraulic Excavator including the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures include using various tools and following steps such as removing bolts, seals, and gears in the specified order and installing components by reversing the removal process. Precautions are outlined such as keeping parts clean and containing fluids.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...fjjskekskem
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. The components include the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications. Safety notices are also included to keep parts clean and contain fluids properly.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...fhshefjjskefkem
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...fujsjefskekfksem
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...ujfjdkkmsme
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...ufjjjskkmsmed
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
This document provides instructions for removing and installing various engine components on a Caterpillar C3.3B engine, including:
- Removing and installing the crankshaft rear seal and wear sleeve.
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing and installing the crankshaft front seal.
- Removing and installing the idler gear.
The document provides detailed step-by-step instructions accompanied by illustrations for each procedure. Safety and cleaning notes are included. Required tools are listed for each job. Torque specifications are provided where applicable.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Tools required are listed for each procedure, and technicians are advised to keep parts clean and contain fluids properly during maintenance.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper fluid disposal.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper disposal.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It describes procedures for removing and installing various engine parts like the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures include lists of required tools and torque specifications for fasteners. Cautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note required tools and torque specifications and include illustrations showing the components and repair steps. Safety notices are also provided regarding keeping components clean and containing fluids.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper disposal.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader with a 3054 engine. It describes the required tools and multi-step processes which include removing bolts, lifting devices, cleaning parts, and torquing fasteners to the specified values. The document contains illustrations supporting each step of the procedures.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...fujskkmdmd
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and rear crankshaft seal. Detailed illustrations and cautions are provided for each step. The process involves drilling holes in the crankshaft rear seal before removing it, cleaning and applying compounds to mating surfaces, and checking dowel pins and gaskets before reassembly.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and reinstalling the mounting bolts. Tools including link brackets and lifting devices are required.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and installing new seals is also covered. Dowels align the housing and bolts attach it to the cylinder block with specified torque.
More Related Content
Similar to Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Manual (TAZ00001 and up).pdf
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...ujfjdkkmsme
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...ufjjjskkmsmed
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
This document provides instructions for removing and installing various engine components on a Caterpillar C3.3B engine, including:
- Removing and installing the crankshaft rear seal and wear sleeve.
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing and installing the crankshaft front seal.
- Removing and installing the idler gear.
The document provides detailed step-by-step instructions accompanied by illustrations for each procedure. Safety and cleaning notes are included. Required tools are listed for each job. Torque specifications are provided where applicable.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Tools required are listed for each procedure, and technicians are advised to keep parts clean and contain fluids properly during maintenance.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper fluid disposal.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper disposal.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It describes procedures for removing and installing various engine parts like the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures include lists of required tools and torque specifications for fasteners. Cautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note required tools and torque specifications and include illustrations showing the components and repair steps. Safety notices are also provided regarding keeping components clean and containing fluids.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like ensuring parts are clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also provided regarding containing fluids and proper disposal.
This document provides instructions for removing and installing various engine components on a 246D Skid Steer Loader powered by a C3.3B engine. The procedures include removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, and crankshaft front seal. Each procedure lists any required tools and provides step-by-step instructions along with caution notices and torque specifications.
Similar to Caterpillar Cat 308E Mini Hydraulic Excavator (Prefix TAZ) Service Repair Manual (TAZ00001 and up).pdf (16)
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 416C Backhoe Loader with a 3054 engine. It describes the required tools and multi-step processes which include removing bolts, lifting devices, cleaning parts, and torquing fasteners to the specified values. The document contains illustrations supporting each step of the procedures.
Caterpillar Cat 320D L Excavator (Prefix PHX) Service Repair Manual (PHX00001...fujskkmdmd
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and rear crankshaft seal. Detailed illustrations and cautions are provided for each step. The process involves drilling holes in the crankshaft rear seal before removing it, cleaning and applying compounds to mating surfaces, and checking dowel pins and gaskets before reassembly.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and reinstalling the mounting bolts. Tools including link brackets and lifting devices are required.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and separating the housing from the cylinder block using light hammer taps if needed. The installation procedure specifies cleaning mating surfaces and tightening mounting bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and installing new seals is also covered. Dowels align the housing and bolts attach it to the cylinder block with specified torque.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The procedure involves using a drill bit to drill out the plastic sleeve holding the seal in place. Once drilled out, the seal can be removed from the front cover housing. Proper cleaning of parts and containment of fluids is emphasized to prevent contamination.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...fujskkmdmd
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and clamps, and disconnecting tubes and hoses to remove the cylinder head.
3. Installing a new gasket and torquing bolts to specified values to install the cylinder head. Reconnecting all tubes, hoses and harness assemblies.
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover by loosening the clamp.
3. Removing the bolts securing the regulator housing and removing the regulator from the engine.
The instructions emphasize cleanliness and safe handling of fluids during maintenance.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual (C3R0000...fujskkmdmd
The document provides instructions for removing and installing a unit injector hydraulic pump on a 322C FM EXCAVATOR C3R powered by a 3126B engine. The removal procedure involves disconnecting hoses and lines, removing bolts, and taking off the pump. The installation procedure specifies lubricating seals, installing bolts, reconnecting lines and hoses, and ensuring connections are secure. Separate sections provide instructions for disassembling and assembling a turbocharger on the same engine model.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual (BPH0000...fujskkmdmd
This document provides instructions for removing and installing a governor from a 322C FM EXCAVATOR engine. It describes disconnecting linkages, removing mounting bolts and clips, and using special tools. Proper cleaning and lubrication of seals is emphasized. References are provided for additional information on governor inspection and testing procedures.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual (CAM0000...fujskkmdmd
The document provides instructions for removing the engine oil filter base from a 322C FM excavator. The procedure involves first removing the turbocharger. Then, using a strap wrench, loosen the oil filter base by turning it counterclockwise. Finally, clean the mating surface before installing the new oil filter base. The summary is provided in 3 sentences or less as requested.
Caterpillar Cat 320D L Excavator (Prefix KLM) Service Repair Manual (KLM00001...fujskkmdmd
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure involves using a slide hammer puller to remove the existing seal after drilling holes in it. For installation, a front seal installer tool is used to carefully push the new seal onto the crankshaft flange. Proper cleaning and containment of fluids is emphasized.
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and rear crankshaft seal. Detailed illustrations and cautions are provided for each step. The process involves drilling holes in the crankshaft rear seal before removing it, cleaning and applying compounds to mating surfaces, and checking dowel pins and gaskets before reassembly.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix EC2) Service Repair ...fujskkmdmd
This document provides instructions for removing and installing various engine components on a Caterpillar 308E2CR Mini Hydraulic Excavator, including the fuel injection pump, electronic unit injectors, turbocharger, and mass air flow pressure sensor. The procedures describe using required tools, disconnecting fuel lines and electrical connections, removing mounting hardware, and installing replacement components in the reverse order while applying specified torques. Safety notices warn technicians to allow the fuel system to purge before opening lines and ensure components like the mass air flow sensor are oriented correctly.
Caterpillar Cat 320D L Excavator (Prefix JFZ) Service Repair Manual (JFZ00001...fujskkmdmd
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
This document provides instructions for removing the crankshaft front seal from a Caterpillar C6.4 engine. The procedure involves using a slide hammer puller tool to remove the seal from the front of the crankshaft. Technicians are advised to keep all parts clean and contain fluids properly during repair work. Removal of the seal prepares the engine for further disassembly or repair of crankshaft components.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix MY2) Service Repair ...fujskkmdmd
The document provides instructions for servicing components of a 308E2CR Mini Hydraulic Excavator engine. It includes procedures for removing and installing components like the exhaust gas recirculation valve, fumes disposal filter, exhaust manifold, and diesel particulate filter. Safety precautions are provided, and the work is to be done in the specified order while applying any recommended lubricants to bolts or studs.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix W8S) Service Repair ...fujskkmdmd
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator, including:
- Removing and installing the diesel particulate filter.
- Removing and installing the inlet manifold.
- Removing and installing the inlet and exhaust valve springs.
- Removing and installing the inlet and exhaust valves.
Detailed step-by-step instructions are provided along with illustrations to correctly complete each procedure. Safety precautions and notes are included throughout.
Caterpillar Cat 308E2CR Mini Hydraulic Excavator (Prefix TMX) Service Repair ...fujskkmdmd
The document provides instructions for removing and installing various engine components on a 308E2CR Mini Hydraulic Excavator including the crankshaft front seal, idler gear, housing (front), valve mechanism cover, bridge dowels, rocker shaft and push rod. The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Safety and installation notes are also provided.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242540
Crankshaft Rear Seal and Wear Sleeve - Remove - Includes
Crankshaft Gear
SMCS - 1161-011; 7558-011
Removal Procedure
Start By:
a. Remove the flywheel.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Place the engine at top dead center.
1/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02799897
2. Use a screw driver to remove rear seal (1).
Illustration 2 g02799899
3. Check the alignment of crankshaft gear (2) and camshaft gear (3). Remove crankshaft gear
(2) and ring seal.
Illustration 3 g02799901
4. Place crankshaft gear (2) with wear sleeve (4) in a suitable vice. Remove wear sleeve (4)
with a suitable chisel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:04:48 UTC+0800 2020
2/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242547
Crankshaft Rear Seal and Wear Sleeve - Install - Includes
Crankshaft Gear
SMCS - 1161-012; 7558-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
390-1146 Crankshaft Rear Seal and Wear Sleeve Driver(1)
1
423-9665 Crank shaft Rear Seal and Wear Sleeve Driver(2)
1
(1)
Used for the C3.3B
(2)
Used for the C2.6
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
1/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g02800138
1. Place wear sleeve (4) on crankshaft gear (2). Position Tooling (A). Use a suitable press and
install wear sleeve (4).
Illustration 2 g02799899
2. Align crankshaft gear (2) with camshaft gear (3). Install crankshaft gear (2) into the
flywheel housing.
Illustration 3 g02800140
3. Apply clean engine oil on the lip of crankshaft rear seal (1). Use Tooling (A) in order to
install crankshaft rear seal (1).
End By:
a. Install the flywheel.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:05:44 UTC+0800 2020
2/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242551
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M12 x 1.25 by 100 mm
2
B 138-7575 Link Brackets 2
Start By:
a. Remove the flywheel.
b. Remove the rear crankshaft seal.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g02794824
1. Remove two bolts (3) from flywheel housing (1).
2. Install Tooling (A) into flywheel housing (1).
3. Install Tooling (B). Install a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb).
4. Remove remaining six bolts (3) and 8 bolts (2) from flywheel housing (1).
5. Remove flywheel housing (1) from the cylinder block.
Illustration 2 g02794825
6. Remove bearing (4).
7. Remove the gasket (5).
8. If necessary, remove the dowels from the cylinder block.
Installation Procedure
1. Install flywheel housing (1) in the reverse order of removal.
2/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g02863884
a. Install liquid gasket to the seam between the lower crankcase section (7) and the
upper crankcase section (6).
b. For the C3.3B tighten 8 bolts (3) and 8 bolts (2) to a torque of 103 to 117 N·m
(76 to 87 lb ft).
c. For the C2.6 tighten 8 bolts (3) and 8 bolts (2) to a torque of 78 to 90 N·m
(58 to 66 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:06:41 UTC+0800 2020
3/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242553
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
a. Remove the v-belt.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g02795206
1. Use a suitable tool in order to prevent the crankshaft from rotating. Remove bolt (2) in order
to remove crankshaft pulley (1).
Installation Procedure
1. Install crankshaft pulley (1) in the reverse order of removal.
a. Apply clean engine oil to the threads of bolt (2). Tighten bolt (2) to a torque of
255 to 274 N·m (188 to 202 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:07:38 UTC+0800 2020
2/2
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: MINI HYD EXCAVATOR
Model: 308E MINI HYD EXCAVATOR TAZ
Configuration: 308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B Engine
Disassembly and Assembly
C2.6 and C3.3B Engines for Caterpillar Built Machines
Media Number -UENR0137-11 Publication Date -01/08/2015 Date Updated -12/07/2018
i05242559
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Start By:
a. Remove the crankshaft pulley.
Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g02795123
Illustration 2 g02795124
1. Use a suitable pry bar to remove crankshaft front seal (1).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 390-1140 Driver 1
B 6V-6640 Sealant 1
Note: The crankshaft front seal should be installed dry. Lubricate the inner rubber portion of the
crankshaft front seal.
2/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 3 g02796112
Illustration 4 g02795123
1. Lubricate the inner rubber portion of crankshaft front seal (1). Apply Tooling (B) on
crankshaft front seal (1). Position crankshaft front seal (1) on Tooling (A). Install crankshaft
front seal (1) on the crankshaft.
End By:
a. Install the crankshaft pulley.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:08:35 UTC+0800 2020
3/3
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Note: Refer to Specification UENR0995 "Engine Design" for non-specified engine Torque
Values.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02795977
3/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g02795978
Illustration 3 g02795981
Alignment of timing marks
1. Ensure that Timing Marks (X) on the camshaft gear and the crankshaft gear are aligned.
Refer to Illustration 1.
2. Ensure that Timing Marks (Y) on the idler gear and the camshaft gear are aligned. Refer to
Illustration 2.
3. Ensure that Timing Marks (Z) on the idler gear and the fuel injection pump gear are aligned.
Refer to Illustration 3.
4/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. Illustration 4 g02795984
4. Remove bolts (2), washer (3), and the idler shaft from idler gear (1). Remove idler gear (1)
and the washer.
Illustration 5 g02795985
5. Use Tooling (A) to remove idler gear bearing (4) from idler gear (1).
Installation Procedure
1. Install idler gear (1) in the reverse order of removal.
2. Tighten bolts (2) to a torque of 30 to 34 N·m (22 to 25 lb ft).
a. Ensure that the gears, cylinder block surface, and idler gear (1) are clean and free
from wear or damage. If necessary, replace any components that are worn or
damaged.
b. Lubricate idler gear bearing surface (4) with clean engine oil.
c. Check oil clearance between the idler gear shaft and the idler gear bushing.
d. Check the idler gear shaft outer diameter and the inner diameter for the idler gear
bushing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:09:32 UTC+0800 2020
5/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Illustration 1 g02795275
2. Disconnect hose assemblies (1) and (2) from the oil cooler.
Illustration 2 g02795251
3. Remove bolts (4).
3/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 4. Remove front housing (3) and the gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the front housing is clean and free from damage. If necessary, replace the front
housing.
2. Clean all the gasket surfaces of the cylinder block.
Illustration 3 g02864317
3. Apply liquid gasket to the seam between the lower crankcase section (6) and the upper
crankcase section (5).
4/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g02795251
4. Align a new gasket and install the gasket to the cylinder block.
5. Tighten 13 bolts (4) in a side to side sequence. Tighten bolts (4) to a torque of 24 to 27 N·m
(18 to 20 lb ft)
Illustration 5 g02795275
6. Connect hose assemblies (1) and (2) to the oil cooler.
End By:
a. Install the crankshaft front seal.
b. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling
System Coolant - Fill" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jan 15 17:10:28 UTC+0800 2020
5/5
308E Mini Hydraulic Excavator TAZ00001-UP (MACHINE) POWERED BY C3.3B ...
2020/1/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...