This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 and 349D2 L excavator, including:
1) Removing the rear gear group by removing bolts, gears, seals, and bushings.
2) Removing the flywheel using lifting tools and bolts.
3) Removing the crankshaft rear seal by removing bolts.
Detailed step-by-step instructions and illustrations are provided for each procedure. Required tools are listed. Safety notices and installation instructions are also included.
Caterpillar cat 349 d l excavator (prefix fla) service repair manual (fla0000...cdsaas
1. The document provides installation and removal instructions for various components of a C13 engine, including the flywheel, rear gear group, crankshaft rear seal, and more.
2. Detailed steps and illustrations are given for each procedure, including the necessary tools. Precautions are outlined, such as containing fluids and keeping parts clean.
3. Specifications and additional reference documents are cited to ensure proper installation and inspection of components like the crankshaft seal surface and wear sleeves.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal on a Caterpillar 730C2 Ejector Articulated Truck. The removal procedure involves removing 11 parts including gears, covers, seals, and bearings. The installation procedure explains how to install 14 of these parts in reverse order, providing details on cleaning, heating, and positioning each part correctly. Tolerances and specifications are provided for proper installation of bearings.
Caterpillar cat d8 n track type tractor dozer bulldozer (prefix 7tk) service ...ufdjjsjefkkkemm
1. The document provides removal and installation instructions for the rear gear group and flywheel on a D8N track-type tractor.
2. The removal process involves using various tools to remove bolts, seals, gears, bushings, and bearings from the rear of the engine.
3. The installation process provides details on cleaning parts and applying threadlock before installing bearings, seals, gears, and bolts in the reverse order of removal. Precise torque specifications and angles are required for proper installation.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists 43 steps to assemble the various components of the torque converter in the correct order. Safety precautions are provided at the beginning regarding lifting heavy components and containing fluids. Diagrams illustrate each step. The summary ends by stating to connect the assembled torque converter housing to the planetary transmission.
Caterpillar cat 345 c hcr material handler excavator (prefix mte) service rep...jfdskekdmme
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. The removal procedure involves removing bolts and seals to access the rear gear components. Tools are required to remove bearings from assemblies. The installation procedure specifies cleaning parts and applying threadlock before installing components in the reverse order of removal, ensuring proper bearing alignment and torque specifications are followed.
Caterpillar cat 349 d l excavator (prefix fla) service repair manual (fla0000...cdsaas
1. The document provides installation and removal instructions for various components of a C13 engine, including the flywheel, rear gear group, crankshaft rear seal, and more.
2. Detailed steps and illustrations are given for each procedure, including the necessary tools. Precautions are outlined, such as containing fluids and keeping parts clean.
3. Specifications and additional reference documents are cited to ensure proper installation and inspection of components like the crankshaft seal surface and wear sleeves.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal on a Caterpillar 730C2 Ejector Articulated Truck. The removal procedure involves removing 11 parts including gears, covers, seals, and bearings. The installation procedure explains how to install 14 of these parts in reverse order, providing details on cleaning, heating, and positioning each part correctly. Tolerances and specifications are provided for proper installation of bearings.
Caterpillar cat d8 n track type tractor dozer bulldozer (prefix 7tk) service ...ufdjjsjefkkkemm
1. The document provides removal and installation instructions for the rear gear group and flywheel on a D8N track-type tractor.
2. The removal process involves using various tools to remove bolts, seals, gears, bushings, and bearings from the rear of the engine.
3. The installation process provides details on cleaning parts and applying threadlock before installing bearings, seals, gears, and bolts in the reverse order of removal. Precise torque specifications and angles are required for proper installation.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists 43 steps to assemble the various components of the torque converter in the correct order. Safety precautions are provided at the beginning regarding lifting heavy components and containing fluids. Diagrams illustrate each step. The summary ends by stating to connect the assembled torque converter housing to the planetary transmission.
Caterpillar cat 345 c hcr material handler excavator (prefix mte) service rep...jfdskekdmme
This document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine. The removal procedure involves removing bolts and seals to access the rear gear components. Tools are required to remove bearings from assemblies. The installation procedure specifies cleaning parts and applying threadlock before installing components in the reverse order of removal, ensuring proper bearing alignment and torque specifications are followed.
Caterpillar Cat 349D2 and 349D2 L Excavator (Prefix WEC) Service Repair Manua...f8uejkdkdmm3e
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1. Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Removing the crankshaft rear seal by removing bolts. Detailed steps and illustrations are provided for each procedure. Required tools are listed.
Caterpillar Cat 349D2 and 349D2 L Excavator (Prefix WEC) Service Repair Manua...f89siekkmdmm2w
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1. Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Removing the crankshaft rear seal by removing bolts. Detailed steps and illustrations are provided for each procedure. Required tools are listed.
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...orrf0370383
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar Cat 349D2 and 349D2 L Excavator (Prefix WEC) Service Repair Manua...yin9niaojiao
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing bolts and seals and using tools to remove bushings and bearings.
2. Procedures for removing and installing the flywheel, which require lifting equipment and specific tools.
3. Steps for removing and installing the crankshaft rear seal, which involve removing bolts and inspecting surfaces according to other guidelines. Precautions are mentioned regarding containment of fluids.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...fujsekmd9idd
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Kawasaki 80 z6 wheel loader parts catalogue manual (serial no. 80c7 0101 and up)hhfjksekmm
This document is a parts catalog for a Hitachi wheel loader powered by a Cummins QSB6.7 engine. It contains a table of contents listing the major systems of the loader and their corresponding parts sections. These include the engine, powertrain, chassis, cab, electrical systems, hydraulics, brakes, and controls. Each part is assigned a unique identification number and name in the catalog for ordering purposes.
Kawasaki 70 z7b wheel loader service repair manual (serial no. 70c6 5001 and up)hhfjksekmm
This document provides disassembly and assembly instructions for removing and installing the cab on a wheel loader. It outlines 14 steps including draining fluids, releasing pressures, removing bolts and covers. Precautions are provided regarding escaping fluids, capping open lines, and ensuring pressures are released from the hydraulic and other systems. The document contains diagrams illustrating the specific components and their locations.
Caterpillar cat 325 l excavator (prefix 7lm) service repair manual (7lm00001 ...hhfjksekmm
This document provides instructions for disassembling the travel motor on 325, 325B, and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Special markings and care are required to keep components in their original positions for reassembly.
Caterpillar cat 325 a fm l excavator (prefix 7 lm) service repair manual (7lm...hhfjksekmm
This document provides instructions for disassembling a travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, identifying each component and how to remove it. This includes removing the head, brake piston, barrel assembly, shoe retainer, springs and other internal components. Special tools may be required and precautions around containing fluids are noted. The process is similar between 325 and 325B excavator models, with some weight and bolt quantity differences called out.
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...hhfjksekmm
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, valves, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers to separate the motor head assembly, rotating group, and individual internal parts in a safe manner while taking precautions for any released spring forces.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...hhfjksekmm
The document provides instructions for removing and installing various engine components on a Caterpillar 349E L excavator, including:
1) Removing and installing electronic unit injector sleeves, which requires using specialized tools to pull the sleeves from the cylinder head and reinstall them with new O-rings.
2) Procedures for removing and installing the air cleaner housing, turbocharger, exhaust balance solenoid valve, and exhaust sensor lines.
3) Detailed illustrations and torque specifications are provided for correctly performing each removal and installation step. Proper cleaning and use of new sealing components is emphasized.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...hhfjksekmm
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...hhfjksekmm
The document provides instructions to disassemble and assemble the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, ring gear, carrier assembly, planetary gears, and seals. It then describes the assembly process, providing specifications for torque and installation of components like bolts, bearings, seals, and shims. Proper cleaning and use of locking compounds or lubricants is emphasized to ensure correct assembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...hhfjksekmm
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing over 20 components including bolts, seals, retainers, discs, and housing assemblies.
3) Assembly is the reverse of disassembly, requiring pressing or installing components like bearings, seals, sleeves and housings back into place and securing with bolts, pins or retaining rings. Cleanliness and use of specified tools and adhesives is important for successful reassembly.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...hhfjksekmm
The document provides instructions for disassembling and assembling the travel motor of a 349E excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order, like installing seals, pins, bearings onto the shaft assembly before pressing it into the motor housing. Tolerances and specifications are provided for components like springs, seals, and fasteners.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly process describes 13 steps and specifications to reinstall components in the reverse order, ensuring proper torque values and lubrication of parts. Key components include the motor housing, head assembly, shaft assembly, barrel assembly, pistons, bearings, seals, springs, and related hardware.
Caterpillar cat 349 e l excavator (prefix mzw) service repair manual (mzw0000...hhfjksekmm
This document provides assembly instructions for a 349E L excavator final drive group. It includes specifications for the components and a step-by-step procedure for assembling the final drive. Some key steps include applying anti-seize compound to bearings, using shims to adjust clearances, and torquing bolts to the specified values. Tools required include a transmission repair stand, eyebolts, and torque wrenches. The assembly procedure has 30 steps and ensures the final drive is properly assembled and adjusted.
More Related Content
Similar to Caterpillar cat 349 d2 excavator (prefix zae) service repair manual (zae00001 and up)
Caterpillar Cat 349D2 and 349D2 L Excavator (Prefix WEC) Service Repair Manua...f8uejkdkdmm3e
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1. Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Removing the crankshaft rear seal by removing bolts. Detailed steps and illustrations are provided for each procedure. Required tools are listed.
Caterpillar Cat 349D2 and 349D2 L Excavator (Prefix WEC) Service Repair Manua...f89siekkmdmm2w
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1. Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Removing the crankshaft rear seal by removing bolts. Detailed steps and illustrations are provided for each procedure. Required tools are listed.
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...orrf0370383
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar Cat 349D2 and 349D2 L Excavator (Prefix WEC) Service Repair Manua...yin9niaojiao
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing bolts and seals and using tools to remove bushings and bearings.
2. Procedures for removing and installing the flywheel, which require lifting equipment and specific tools.
3. Steps for removing and installing the crankshaft rear seal, which involve removing bolts and inspecting surfaces according to other guidelines. Precautions are mentioned regarding containment of fluids.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...fujsekmd9idd
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Similar to Caterpillar cat 349 d2 excavator (prefix zae) service repair manual (zae00001 and up) (6)
Kawasaki 80 z6 wheel loader parts catalogue manual (serial no. 80c7 0101 and up)hhfjksekmm
This document is a parts catalog for a Hitachi wheel loader powered by a Cummins QSB6.7 engine. It contains a table of contents listing the major systems of the loader and their corresponding parts sections. These include the engine, powertrain, chassis, cab, electrical systems, hydraulics, brakes, and controls. Each part is assigned a unique identification number and name in the catalog for ordering purposes.
Kawasaki 70 z7b wheel loader service repair manual (serial no. 70c6 5001 and up)hhfjksekmm
This document provides disassembly and assembly instructions for removing and installing the cab on a wheel loader. It outlines 14 steps including draining fluids, releasing pressures, removing bolts and covers. Precautions are provided regarding escaping fluids, capping open lines, and ensuring pressures are released from the hydraulic and other systems. The document contains diagrams illustrating the specific components and their locations.
Caterpillar cat 325 l excavator (prefix 7lm) service repair manual (7lm00001 ...hhfjksekmm
This document provides instructions for disassembling the travel motor on 325, 325B, and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Special markings and care are required to keep components in their original positions for reassembly.
Caterpillar cat 325 a fm l excavator (prefix 7 lm) service repair manual (7lm...hhfjksekmm
This document provides instructions for disassembling a travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, identifying each component and how to remove it. This includes removing the head, brake piston, barrel assembly, shoe retainer, springs and other internal components. Special tools may be required and precautions around containing fluids are noted. The process is similar between 325 and 325B excavator models, with some weight and bolt quantity differences called out.
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...hhfjksekmm
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, valves, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers to separate the motor head assembly, rotating group, and individual internal parts in a safe manner while taking precautions for any released spring forces.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...hhfjksekmm
The document provides instructions for removing and installing various engine components on a Caterpillar 349E L excavator, including:
1) Removing and installing electronic unit injector sleeves, which requires using specialized tools to pull the sleeves from the cylinder head and reinstall them with new O-rings.
2) Procedures for removing and installing the air cleaner housing, turbocharger, exhaust balance solenoid valve, and exhaust sensor lines.
3) Detailed illustrations and torque specifications are provided for correctly performing each removal and installation step. Proper cleaning and use of new sealing components is emphasized.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...hhfjksekmm
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...hhfjksekmm
The document provides instructions to disassemble and assemble the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, ring gear, carrier assembly, planetary gears, and seals. It then describes the assembly process, providing specifications for torque and installation of components like bolts, bearings, seals, and shims. Proper cleaning and use of locking compounds or lubricants is emphasized to ensure correct assembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...hhfjksekmm
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing over 20 components including bolts, seals, retainers, discs, and housing assemblies.
3) Assembly is the reverse of disassembly, requiring pressing or installing components like bearings, seals, sleeves and housings back into place and securing with bolts, pins or retaining rings. Cleanliness and use of specified tools and adhesives is important for successful reassembly.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...hhfjksekmm
The document provides instructions for disassembling and assembling the travel motor of a 349E excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order, like installing seals, pins, bearings onto the shaft assembly before pressing it into the motor housing. Tolerances and specifications are provided for components like springs, seals, and fasteners.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly process describes 13 steps and specifications to reinstall components in the reverse order, ensuring proper torque values and lubrication of parts. Key components include the motor housing, head assembly, shaft assembly, barrel assembly, pistons, bearings, seals, springs, and related hardware.
Caterpillar cat 349 e l excavator (prefix mzw) service repair manual (mzw0000...hhfjksekmm
This document provides assembly instructions for a 349E L excavator final drive group. It includes specifications for the components and a step-by-step procedure for assembling the final drive. Some key steps include applying anti-seize compound to bearings, using shims to adjust clearances, and torquing bolts to the specified values. Tools required include a transmission repair stand, eyebolts, and torque wrenches. The assembly procedure has 30 steps and ensures the final drive is properly assembled and adjusted.
Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz0000...hhfjksekmm
This document provides instructions for removing and installing a water pump on a 349E L excavator. The removal procedure involves: 1) Removing the water temperature regulator and fan drive; 2) Removing various sheet assemblies and supports; 3) Disconnecting support assemblies and repositioning harness assemblies; 4) Removing hoses. The installation procedure involves reversing the removal steps and applying threadlock to bolts.
Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx0000...hhfjksekmm
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
Caterpillar cat 349 e l excavator (prefix fjb) service repair manual (fjb0000...hhfjksekmm
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. It describes 22 steps to disassemble the components, including removing bolts, retainers, seals, discs, and housing parts. It then describes 14 steps for reassembling the components, applying sealant and installing seals, sleeves, bearings and housing pieces in the reverse order of disassembly. Precision cleaning and special tools are required to prevent damage to parts during the process.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...hhfjksekmm
The document provides instructions for removing and installing various engine components on a Caterpillar 349E L excavator, including:
1) Removing and installing electronic unit injector sleeves, which requires using specialized tools to pull the sleeves from the cylinder head and clean the bore before reinstalling with new O-rings.
2) Procedures for removing and installing the air cleaner housing, turbocharger, exhaust balance solenoid valve, and exhaust sensor lines.
3) Detailed illustrations and torque specifications are provided for correctly performing each removal and installation step.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 L EXCAVATOR ZAE
Configuration: 349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06931709
Gear Group (Rear) - Remove and Install
SMCS - 1206-010; 1212-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp. 1
B 1P-0510 Driver Gp 1
Start By:
a. Remove the electric starting motor.
b. Remove the flywheel.
1. Support the engine.
1/10
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g06002548
2. Remove bolts (2) and rear crankshaft seal (1).
Illustration 2 g06002556
3. Remove bolts (4) and the washers. Remove cover (3) and the seal.
Illustration 3 g06002558
4. Remove gear (7), bolts (6), and gear (5).
Illustration 4 g06002564
2/10
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 5. Remove O-ring seal (8) from gear (7).
Illustration 5 g06172622
6. Use Tooling (A) to remove bushing (7A) from gear assembly (7).
Illustration 6 g06172537
7. Remove bolts (9), adapter assembly (10), and the O-ring seal.
Illustration 7 g06172541
8. Use Tooling (B) to remove bearing (11) from adapter assembly (10).
3/10
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 8 g06172549
9. Remove gear assembly (12).
Illustration 9 g06172554
10. Remove cover (13) and the O-ring seal.
Illustration 10 g06172557
11. Use Tooling (B) to remove bearing (14).
Installation Procedure
4/10
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Table 2
Required Tools
Tool Part Number Part Description Qty
A 095-0706 Bolt 2
Illustration 11 g06172557
Illustration 12 g06172580
5/10
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 13 g06172587
1. Lower the temperature of bearing (14). Be sure to match Dimension (B) and Dimension (C)
when installing bearing (14.). Dimension (B) indicates the angle of the joint on bearing (14).
Dimension (B) is 15° ± 1°. Dimension (C) shows the distance from bearing (14) to the end
of the bore. Dimension (C) is 4.000 ± 0.500 mm (0.1575 ± 0.0197 inch).
Illustration 14 g06172554
2. Install the O-ring seal and cover (9).
6/10
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g06172597
3. Install gear assembly (12) with oil passage plug (12A) facing out.
Illustration 16 g06172601
Illustration 17 g06172609
4. Lower the temperature of bearing (11). Be sure to match Dimension (F) and Dimension (G)
when installing bearing (11) into adapter assembly (10). Dimension (F) indicates the angle
of the joint on bearing (11). Dimension (F) is 15° ± 1°. Dimension (G) shows the distance
from bearing (11) to the end of the bore. Dimension (G) is 3.500 ± 0.500 mm
(0.1378 ± 0.0197 inch).
7/10
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 18 g06172537
5. Install the O-ring seal, adapter assembly (10), and bolts (9).
Illustration 19 g06172619
6. Lower the temperature of bearing (7A). Install bearing (7A) into gear assembly (7). Be sure
that each relief (H) is within 2° of each relief in gear assembly (7).
Illustration 20 g06002564
7. Install O-ring seal (8) onto gear (7).
8/10
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 21 g06002578
8. Install gear (5) and bolts (6).
Note: Tooling (A) is for supporting gear (7) during the installation of the cover and the rear
crankshaft seal.
Note: The bolt holes in gear (7) are not symmetrical. When installing Tooling (C), check
the rest of the bolts holes in gear (7) are aligned with the holes in the crankshaft.
9. Install gear (7) and Tooling (C).
Illustration 22 g06002581
10. Install cover (3), the seal, bolts (4), and the washers.
9/10
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g06002592
11. Install rear crankshaft seal (1) and bolts (2).
12. Remove Tooling (C).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 10:21:21 UTC+0800 2020
10/10
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 E...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 L EXCAVATOR ZAE
Configuration: 349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249234
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
1/2
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01132214
1. Attach Tooling (A) and a suitable lifting device to flywheel (2). The weight of flywheel (2)
is approximately 79 kg (175 lb).
2. Remove top bolt (1). Install Tooling (B).
3. Remove remaining bolts (1).
4. Remove flywheel (2).
5. Use a hammer and a punch in order to remove the ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 10:22:17 UTC+0800 2020
2/2
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 L EXCAVATOR ZAE
Configuration: 349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06123534
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
C - Loctite 242 1
Always wear protective gloves when handling parts that have been
heated.
1. Raise the temperature of the ring gear. Position the ring gear with the part number toward
the crankshaft. Install the ring gear on the flywheel. Allow the ring gear to cool. Use a soft
hammer in order to seat the ring gear against the shoulder of the flywheel.
1/2
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g01132214
2. Attach Tooling (A) and a suitable lifting device to flywheel (2) . The weight of flywheel (2)
is approximately 79 kg (175 lb).
3. Position flywheel (2) on Tooling (B) .
4. Apply Tooling (C) to bolts (1) .
5. Install bolts (1) . Remove Tooling (B) . Install remaining bolt (1) . Tighten the bolts evenly
to a torque of 300 ± 40 N·m (221 ± 30 lb ft).
6. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for the
correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 10:23:13 UTC+0800 2020
2/2
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 L EXCAVATOR ZAE
Configuration: 349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010889
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01132235
1. Remove bolts (1).
2. Remove crankshaft rear seal (2).
Note: Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and
Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
Note: Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9,
C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the
correct specifications of the crankshaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 10:24:09 UTC+0800 2020
2/2
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 L EXCAVATOR ZAE
Configuration: 349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010890
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01140085
Illustration 2 g03698745
Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information
please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage
Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12,
2/3
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications
of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual
Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the
crankshaft seal surface.
1. If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the
crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
a. Clean and polish the crankshaft of imperfections.
b. Use Tooling (A) to clean the outside diameter of the crankshaft and the inside
diameter of the crankshaft wear sleeve.
c. Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of
the crankshaft wear sleeve.
d. Use Tooling (C) to install the crankshaft wear sleeve.
Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft
rear seal must be installed dry.
Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these
components should not be used.
2. Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal
(1).
3. Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push
crankshaft rear seal (1) in place to dislodge the shipping sleeve.
Note: Do not remove the shipping sleeve until bolts (2) are installed.
4. Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in
Illustration 2. Tighten bolts (2) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 10:25:04 UTC+0800 2020
3/3
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D2 L EXCAVATOR ZAE
Configuration: 349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249340
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
1. Support the engine.
Illustration 1 g01132273
1/3
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb).
3. Remove bolts (1) and flywheel housing (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8846 Gasket Sealant 1
1. Apply Tooling (A) to the face of the cylinder block.
Illustration 2 g01132273
2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb). Position flywheel housing (2) on the rear of the cylinder
block.
3. Install bolts (1).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Mon Sep 14 10:26:00 UTC+0800 2020
2/3
349D2 & 349D2 L Excavators ZAE00001-UP (MACHINE) POWERED BY C13 Engi...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...