The document provides instructions for removing and installing various engine components on a Caterpillar 349E L excavator, including:
1) Removing and installing electronic unit injector sleeves, which requires using specialized tools to pull the sleeves from the cylinder head and clean the bore before reinstalling with new O-rings.
2) Procedures for removing and installing the air cleaner housing, turbocharger, exhaust balance solenoid valve, and exhaust sensor lines.
3) Detailed illustrations and torque specifications are provided for correctly performing each removal and installation step.
Caterpillar cat 349 f l excavator (prefix hlb) service repair manual (hlb0000...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...cdsaas
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 d2 l excavator (prefix yae) service repair manual (yae000...cdsaas
The document provides instructions for assembling and installing a travel motor. It outlines 33 steps for assembling components like pistons, seals, plates, and bearings. Measurement checks are specified to ensure proper assembly. Tools required are listed. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx0000...cdsaas
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps, covering lubrication of parts and installation of components in reverse order of disassembly, like installing seals, springs, pistons, and housing pieces. Specifications are provided for torque and dimensions of components. Required tools are listed.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, plates and shafts. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing springs and seals. Tools required for specific steps are also listed.
Caterpillar cat 311 f lrr excavator (prefix kcw) service repair manual (kcw00...fjskekdmjekm
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 311F LRR excavator. It lists over 30 detailed steps to disassemble components like the sprockets, traction control valve, piston assemblies, barrel assembly, planetary gear assemblies, and more. Safety notices are included throughout to warn technicians of potential hazards like parts propelled by springs during disassembly. Required tools are listed at the beginning, along with references to other documents for fluid capacities and tool part numbers.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by taking apart the shaft assembly. It then lists 25 steps for reassembly in reverse order, starting with pressing the inner race back onto the shaft and ending by installing the port plate. Precautions are provided regarding cleanliness, identification marks, and pressurized springs. Tools required include link brackets, a slide hammer, bearing puller, and molybdenum grease.
Caterpillar cat 336 f l excavator (prefix wtz) service repair manual (wtz0000...fjsjekdmmeme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. The disassembly procedure involves 30 steps to remove components like springs, seals, plates, and housing pieces. The assembly procedure reverses the disassembly with 23 steps like installing seals, springs, pistons and housing components. Special tools are listed and safety notices are provided regarding spring forces and component alignment.
Caterpillar cat 349 f l excavator (prefix hlb) service repair manual (hlb0000...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...cdsaas
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 d2 l excavator (prefix yae) service repair manual (yae000...cdsaas
The document provides instructions for assembling and installing a travel motor. It outlines 33 steps for assembling components like pistons, seals, plates, and bearings. Measurement checks are specified to ensure proper assembly. Tools required are listed. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx0000...cdsaas
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps, covering lubrication of parts and installation of components in reverse order of disassembly, like installing seals, springs, pistons, and housing pieces. Specifications are provided for torque and dimensions of components. Required tools are listed.
Caterpillar cat 315 c excavator (prefix cft) service repair manual (cft00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 315C. It describes 27 steps to disassemble the motor by removing components like bolts, seals, bearings, pistons, plates and shafts. It then describes 26 steps for reassembling the motor by installing these components in the reverse order. Precautions are provided to mark parts, clean them, apply lubricants and take care when removing or installing springs and seals. Tools required for specific steps are also listed.
Caterpillar cat 311 f lrr excavator (prefix kcw) service repair manual (kcw00...fjskekdmjekm
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 311F LRR excavator. It lists over 30 detailed steps to disassemble components like the sprockets, traction control valve, piston assemblies, barrel assembly, planetary gear assemblies, and more. Safety notices are included throughout to warn technicians of potential hazards like parts propelled by springs during disassembly. Required tools are listed at the beginning, along with references to other documents for fluid capacities and tool part numbers.
Caterpillar cat 315 c excavator (prefix ake) service repair manual (ake00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of a 315C excavator. It lists 28 steps for disassembly, beginning with removing the piston motor and ending by taking apart the shaft assembly. It then lists 25 steps for reassembly in reverse order, starting with pressing the inner race back onto the shaft and ending by installing the port plate. Precautions are provided regarding cleanliness, identification marks, and pressurized springs. Tools required include link brackets, a slide hammer, bearing puller, and molybdenum grease.
Caterpillar cat 336 f l excavator (prefix wtz) service repair manual (wtz0000...fjsjekdmmeme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. The disassembly procedure involves 30 steps to remove components like springs, seals, plates, and housing pieces. The assembly procedure reverses the disassembly with 23 steps like installing seals, springs, pistons and housing components. Special tools are listed and safety notices are provided regarding spring forces and component alignment.
Caterpillar cat 279 c compact track loader (prefix mbt) service repair manual...ufjjskekkmde
This document provides instructions for disassembling the piston motor (hydrostatic) on a 279C Compact Track Loader. The removal procedure involves 17 steps, including removing hoses, harnesses, bolts, springs, plates, gears, seals, bearings, and other components from the head, barrel assembly, housing, and spindle. Precautions are listed regarding releasing spring forces and containing fluids during the process. Required tools include retaining ring pliers, a slide hammer puller, threaded adapters, drivers, bearing pullers, reaction plates, and a hydraulic wrench.
Caterpillar cat 336 f l excavator (prefix ssn) service repair manual (ssn0000...fjsjekdmmeme
This document provides disassembly and assembly instructions for a 336F L excavator travel motor. The disassembly process involves removing 30 components from the travel motor in a specific sequence. Safety precautions are outlined due to parts under spring tension. The assembly section describes installing 35 components back into the travel motor housing following the reverse of the disassembly order. Tools required are listed for both procedures.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 319 d l excavator (prefix fmh) service repair manual (fmh0000...fjkskedmme
This document provides instructions for disassembling and assembling a travel motor. The 27-step disassembly procedure involves removing components like the head, brake piston, barrel assembly, and shaft assembly. The 23-step assembly procedure describes reinstalling these components in reverse order and provides notices about proper installation of parts like the cam plate and keys. Precise alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar cat 374 f l excavator (prefix mfl) service repair manual (mfl0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. The disassembly process involves removing over 30 individual parts in a specific sequence, including carrier assemblies, gears, shafts, seals, and housings. The assembly process reverses the disassembly steps and provides details on installing new seals, applying thread locking compounds, and lifting components into place using specialized tools. Precise following of the step-by-step instructions is required to correctly take apart and rebuild the final drive transmission.
Caterpillar cat 390 f l excavator (prefix tye) service repair manual (tye0000...fujskekfmsme
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It lists 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then lists 12 steps for reassembly, starting with installing a lip seal and finishing by reinstalling covers. Precautions are provided regarding cleaning parts and applying oil before assembly.
Caterpillar cat 352 f excavator (prefix a9j) service repair manual (a9j00001 ...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator. The disassembly procedure involves removing 17 components from the travel motor housing including the head assembly, brake housing, rotating group, barrel assembly, pistons, and bearings. The assembly procedure instructs installing the components in reverse order.
Caterpillar cat 325 f lcr excavator (prefix xaa) service repair manual (xaa00...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps for disassembly, including removing the head, check valve assemblies, fittings, seals, pistons, and other components. It then describes 11 steps for assembly, including installing seals, bearings, keys, and other parts in the reverse order of disassembly. Personal protective equipment is recommended and cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar cat 349 e excavator (prefix rgh) service repair manual (rgh00001 ...cdsaas
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided for correct installation of components.
Caterpillar cat 318 f l excavator (prefix hcp) service repair manual (hcp0000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for assembly, instructing technicians to install these components in reverse order. Safety warnings are provided throughout to avoid injury from spring forces. The document is intended to guide maintenance technicians through a complete travel motor overhaul.
Caterpillar cat 325 b l excavator (prefix 4ds) service repair manual (4ds0000...fjjskekdmme
This document provides instructions for removing and installing an exhaust manifold on a 325B L excavator powered by a 3116 engine. The removal procedure involves removing bolts and gaskets from the cylinder head assembly. The installation procedure specifies applying anti-seize compound to mounting studs and high temperature sealer if the manifold has multiple pieces, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
This document provides assembly instructions for a piston pump in a Caterpillar 226B3 skid steer loader. It lists 78 steps to assemble components like bearings, seals, pins, springs and plates. Tools required include rulers, pliers, drivers and pullers. Pictures illustrate each step and call out safety when working with spring-loaded parts. The instructions specify tightening torques and note that some parts are marked for correct orientation.
Caterpillar cat 352 f xe vg excavator (prefix sd2) service repair manual (sd2...fjjskekmsemm
This document provides instructions for disassembling and assembling the travel motor on a 352F XE VG Excavator. The disassembly procedure involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly procedure describes 18 steps and includes specifications for installing components and torquing fasteners correctly. Tools required are listed for both the disassembly and assembly processes.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...cdsaas
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
Caterpillar cat 349 e l hvg uhd mobile hydraulic (prefix jae) service repair ...fjjskekmsemm
This document provides instructions for removing and installing various components on a 349E L HVG UHD Mobile Hydraulic Power Unit. It describes how to remove and install electronic unit injector sleeves, air cleaners, turbochargers, solenoid valves, exhaust sensor lines, air control valves, and other parts. Detailed steps and illustrations are provided, along with required tools and torque specifications for reinstallation.
Caterpillar cat 349 e l hvg uhd mobile hydraulic (prefix jae) service repair ...fjjskekdmme
This document provides instructions for removing and installing various components on a 349E L HVG UHD Mobile Hydraulic Power Unit. It describes how to remove and install electronic unit injector sleeves, air cleaners, turbochargers, solenoid valves, exhaust sensor lines, air control valves, and other parts. Detailed steps and illustrations are provided, along with required tools and torque specifications for reinstallation.
Caterpillar Cat 349E L HVG UHD Mobile Hydraulic (Prefix JAE) Service Repair M...yan77xunhao
The document provides instructions for removing and installing various components of a 349E L HVG UHD Mobile Hydraulic Power Unit, including:
1) Removing and installing electronic unit injector sleeves from the cylinder head.
2) Removing and installing the air cleaner housing.
3) Removing and installing the turbocharger.
4) Removing and installing the exhaust balance solenoid valve.
5) Removing and installing the exhaust sensor lines and venturi.
Caterpillar Cat 349E L HVG UHD Mobile Hydraulic (Prefix JAE) Service Repair M...jdjkskmikdkmd
The document provides instructions for removing and installing various components of a 349E L HVG UHD Mobile Hydraulic Power Unit, including:
1) Removing and installing electronic unit injector sleeves from the cylinder head.
2) Removing and installing the air cleaner housing.
3) Removing and installing the turbocharger.
4) Removing and installing the exhaust balance solenoid valve.
5) Removing and installing the exhaust sensor lines and venturi.
Caterpillar cat 349 e l hvg uhd mobile hydraulic (prefix jae) service repair ...fios9dkksd
This document provides instructions for removing and installing various components on a 349E L HVG UHD Mobile Hydraulic Power Unit powered by a C13 engine. It includes procedures for removing and installing electronic unit injector sleeves, air cleaners, turbochargers, solenoid valves, exhaust sensor lines, air control valves, and other parts. Detailed steps are outlined along with required tools and specifications for tightening fasteners.
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator. The disassembly procedure involves removing 17 components from the travel motor housing including the head assembly, brake housing, rotating group, barrel assembly, pistons, and bearings. The assembly procedure instructs installing the components in reverse order.
Kawasaki 80 z6 wheel loader parts catalogue manual (serial no. 80c7 0101 and up)hhfjksekmm
This document is a parts catalog for a Hitachi wheel loader powered by a Cummins QSB6.7 engine. It contains a table of contents listing the major systems of the loader and their corresponding parts sections. These include the engine, powertrain, chassis, cab, electrical systems, hydraulics, brakes, and controls. Each part is assigned a unique identification number and name in the catalog for ordering purposes.
Caterpillar cat 279 c compact track loader (prefix mbt) service repair manual...ufjjskekkmde
This document provides instructions for disassembling the piston motor (hydrostatic) on a 279C Compact Track Loader. The removal procedure involves 17 steps, including removing hoses, harnesses, bolts, springs, plates, gears, seals, bearings, and other components from the head, barrel assembly, housing, and spindle. Precautions are listed regarding releasing spring forces and containing fluids during the process. Required tools include retaining ring pliers, a slide hammer puller, threaded adapters, drivers, bearing pullers, reaction plates, and a hydraulic wrench.
Caterpillar cat 336 f l excavator (prefix ssn) service repair manual (ssn0000...fjsjekdmmeme
This document provides disassembly and assembly instructions for a 336F L excavator travel motor. The disassembly process involves removing 30 components from the travel motor in a specific sequence. Safety precautions are outlined due to parts under spring tension. The assembly section describes installing 35 components back into the travel motor housing following the reverse of the disassembly order. Tools required are listed for both procedures.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 319 d l excavator (prefix fmh) service repair manual (fmh0000...fjkskedmme
This document provides instructions for disassembling and assembling a travel motor. The 27-step disassembly procedure involves removing components like the head, brake piston, barrel assembly, and shaft assembly. The 23-step assembly procedure describes reinstalling these components in reverse order and provides notices about proper installation of parts like the cam plate and keys. Precise alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar cat 374 f l excavator (prefix mfl) service repair manual (mfl0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. The disassembly process involves removing over 30 individual parts in a specific sequence, including carrier assemblies, gears, shafts, seals, and housings. The assembly process reverses the disassembly steps and provides details on installing new seals, applying thread locking compounds, and lifting components into place using specialized tools. Precise following of the step-by-step instructions is required to correctly take apart and rebuild the final drive transmission.
Caterpillar cat 390 f l excavator (prefix tye) service repair manual (tye0000...fujskekfmsme
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It lists 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then lists 12 steps for reassembly, starting with installing a lip seal and finishing by reinstalling covers. Precautions are provided regarding cleaning parts and applying oil before assembly.
Caterpillar cat 352 f excavator (prefix a9j) service repair manual (a9j00001 ...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator. The disassembly procedure involves removing 17 components from the travel motor housing including the head assembly, brake housing, rotating group, barrel assembly, pistons, and bearings. The assembly procedure instructs installing the components in reverse order.
Caterpillar cat 325 f lcr excavator (prefix xaa) service repair manual (xaa00...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps for disassembly, including removing the head, check valve assemblies, fittings, seals, pistons, and other components. It then describes 11 steps for assembly, including installing seals, bearings, keys, and other parts in the reverse order of disassembly. Personal protective equipment is recommended and cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar cat 349 e excavator (prefix rgh) service repair manual (rgh00001 ...cdsaas
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided for correct installation of components.
Caterpillar cat 318 f l excavator (prefix hcp) service repair manual (hcp0000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for assembly, instructing technicians to install these components in reverse order. Safety warnings are provided throughout to avoid injury from spring forces. The document is intended to guide maintenance technicians through a complete travel motor overhaul.
Caterpillar cat 325 b l excavator (prefix 4ds) service repair manual (4ds0000...fjjskekdmme
This document provides instructions for removing and installing an exhaust manifold on a 325B L excavator powered by a 3116 engine. The removal procedure involves removing bolts and gaskets from the cylinder head assembly. The installation procedure specifies applying anti-seize compound to mounting studs and high temperature sealer if the manifold has multiple pieces, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
This document provides assembly instructions for a piston pump in a Caterpillar 226B3 skid steer loader. It lists 78 steps to assemble components like bearings, seals, pins, springs and plates. Tools required include rulers, pliers, drivers and pullers. Pictures illustrate each step and call out safety when working with spring-loaded parts. The instructions specify tightening torques and note that some parts are marked for correct orientation.
Caterpillar cat 352 f xe vg excavator (prefix sd2) service repair manual (sd2...fjjskekmsemm
This document provides instructions for disassembling and assembling the travel motor on a 352F XE VG Excavator. The disassembly procedure involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly procedure describes 18 steps and includes specifications for installing components and torquing fasteners correctly. Tools required are listed for both the disassembly and assembly processes.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...cdsaas
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
Caterpillar cat 349 e l hvg uhd mobile hydraulic (prefix jae) service repair ...fjjskekmsemm
This document provides instructions for removing and installing various components on a 349E L HVG UHD Mobile Hydraulic Power Unit. It describes how to remove and install electronic unit injector sleeves, air cleaners, turbochargers, solenoid valves, exhaust sensor lines, air control valves, and other parts. Detailed steps and illustrations are provided, along with required tools and torque specifications for reinstallation.
Caterpillar cat 349 e l hvg uhd mobile hydraulic (prefix jae) service repair ...fjjskekdmme
This document provides instructions for removing and installing various components on a 349E L HVG UHD Mobile Hydraulic Power Unit. It describes how to remove and install electronic unit injector sleeves, air cleaners, turbochargers, solenoid valves, exhaust sensor lines, air control valves, and other parts. Detailed steps and illustrations are provided, along with required tools and torque specifications for reinstallation.
Caterpillar Cat 349E L HVG UHD Mobile Hydraulic (Prefix JAE) Service Repair M...yan77xunhao
The document provides instructions for removing and installing various components of a 349E L HVG UHD Mobile Hydraulic Power Unit, including:
1) Removing and installing electronic unit injector sleeves from the cylinder head.
2) Removing and installing the air cleaner housing.
3) Removing and installing the turbocharger.
4) Removing and installing the exhaust balance solenoid valve.
5) Removing and installing the exhaust sensor lines and venturi.
Caterpillar Cat 349E L HVG UHD Mobile Hydraulic (Prefix JAE) Service Repair M...jdjkskmikdkmd
The document provides instructions for removing and installing various components of a 349E L HVG UHD Mobile Hydraulic Power Unit, including:
1) Removing and installing electronic unit injector sleeves from the cylinder head.
2) Removing and installing the air cleaner housing.
3) Removing and installing the turbocharger.
4) Removing and installing the exhaust balance solenoid valve.
5) Removing and installing the exhaust sensor lines and venturi.
Caterpillar cat 349 e l hvg uhd mobile hydraulic (prefix jae) service repair ...fios9dkksd
This document provides instructions for removing and installing various components on a 349E L HVG UHD Mobile Hydraulic Power Unit powered by a C13 engine. It includes procedures for removing and installing electronic unit injector sleeves, air cleaners, turbochargers, solenoid valves, exhaust sensor lines, air control valves, and other parts. Detailed steps are outlined along with required tools and specifications for tightening fasteners.
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator. The disassembly procedure involves removing 17 components from the travel motor housing including the head assembly, brake housing, rotating group, barrel assembly, pistons, and bearings. The assembly procedure instructs installing the components in reverse order.
Similar to Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc00001 and up) (6)
Kawasaki 80 z6 wheel loader parts catalogue manual (serial no. 80c7 0101 and up)hhfjksekmm
This document is a parts catalog for a Hitachi wheel loader powered by a Cummins QSB6.7 engine. It contains a table of contents listing the major systems of the loader and their corresponding parts sections. These include the engine, powertrain, chassis, cab, electrical systems, hydraulics, brakes, and controls. Each part is assigned a unique identification number and name in the catalog for ordering purposes.
Kawasaki 70 z7b wheel loader service repair manual (serial no. 70c6 5001 and up)hhfjksekmm
This document provides disassembly and assembly instructions for removing and installing the cab on a wheel loader. It outlines 14 steps including draining fluids, releasing pressures, removing bolts and covers. Precautions are provided regarding escaping fluids, capping open lines, and ensuring pressures are released from the hydraulic and other systems. The document contains diagrams illustrating the specific components and their locations.
Caterpillar cat 325 l excavator (prefix 7lm) service repair manual (7lm00001 ...hhfjksekmm
This document provides instructions for disassembling the travel motor on 325, 325B, and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Special markings and care are required to keep components in their original positions for reassembly.
Caterpillar cat 325 a fm l excavator (prefix 7 lm) service repair manual (7lm...hhfjksekmm
This document provides instructions for disassembling a travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, identifying each component and how to remove it. This includes removing the head, brake piston, barrel assembly, shoe retainer, springs and other internal components. Special tools may be required and precautions around containing fluids are noted. The process is similar between 325 and 325B excavator models, with some weight and bolt quantity differences called out.
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...hhfjksekmm
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, valves, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers to separate the motor head assembly, rotating group, and individual internal parts in a safe manner while taking precautions for any released spring forces.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...hhfjksekmm
The document provides instructions for removing and installing various engine components on a Caterpillar 349E L excavator, including:
1) Removing and installing electronic unit injector sleeves, which requires using specialized tools to pull the sleeves from the cylinder head and reinstall them with new O-rings.
2) Procedures for removing and installing the air cleaner housing, turbocharger, exhaust balance solenoid valve, and exhaust sensor lines.
3) Detailed illustrations and torque specifications are provided for correctly performing each removal and installation step. Proper cleaning and use of new sealing components is emphasized.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...hhfjksekmm
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...hhfjksekmm
The document provides instructions to disassemble and assemble the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, ring gear, carrier assembly, planetary gears, and seals. It then describes the assembly process, providing specifications for torque and installation of components like bolts, bearings, seals, and shims. Proper cleaning and use of locking compounds or lubricants is emphasized to ensure correct assembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...hhfjksekmm
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing over 20 components including bolts, seals, retainers, discs, and housing assemblies.
3) Assembly is the reverse of disassembly, requiring pressing or installing components like bearings, seals, sleeves and housings back into place and securing with bolts, pins or retaining rings. Cleanliness and use of specified tools and adhesives is important for successful reassembly.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...hhfjksekmm
The document provides instructions for disassembling and assembling the travel motor of a 349E excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order, like installing seals, pins, bearings onto the shaft assembly before pressing it into the motor housing. Tolerances and specifications are provided for components like springs, seals, and fasteners.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly process describes 13 steps and specifications to reinstall components in the reverse order, ensuring proper torque values and lubrication of parts. Key components include the motor housing, head assembly, shaft assembly, barrel assembly, pistons, bearings, seals, springs, and related hardware.
Caterpillar cat 349 e l excavator (prefix mzw) service repair manual (mzw0000...hhfjksekmm
This document provides assembly instructions for a 349E L excavator final drive group. It includes specifications for the components and a step-by-step procedure for assembling the final drive. Some key steps include applying anti-seize compound to bearings, using shims to adjust clearances, and torquing bolts to the specified values. Tools required include a transmission repair stand, eyebolts, and torque wrenches. The assembly procedure has 30 steps and ensures the final drive is properly assembled and adjusted.
Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz0000...hhfjksekmm
This document provides instructions for removing and installing a water pump on a 349E L excavator. The removal procedure involves: 1) Removing the water temperature regulator and fan drive; 2) Removing various sheet assemblies and supports; 3) Disconnecting support assemblies and repositioning harness assemblies; 4) Removing hoses. The installation procedure involves reversing the removal steps and applying threadlock to bolts.
Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx0000...hhfjksekmm
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
Caterpillar cat 349 e l excavator (prefix fjb) service repair manual (fjb0000...hhfjksekmm
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. It describes 22 steps to disassemble the components, including removing bolts, retainers, seals, discs, and housing parts. It then describes 14 steps for reassembling the components, applying sealant and installing seals, sleeves, bearings and housing pieces in the reverse order of disassembly. Precision cleaning and special tools are required to prevent damage to parts during the process.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...hhfjksekmm
The document provides instructions to disassemble and assemble the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive by removing components like the coupling, cover, ring gear, carrier assembly, planetary gears, and seals. It then describes the assembly process in reverse, providing specifications for torque and application of sealants or lubricants during reassembly. Precise alignment and orientation of parts is emphasized to ensure proper reassembly.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR ETC
Configuration: 349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13
Engines for Caterpillar Built Machines
Media Number -KENR8150-05 Publication Date -01/01/2014 Date Updated -22/01/2014
i03531892
Electronic Unit Injector Sleeve - Remove and Install
SMCS - 1713-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6891 Injector Tool Group 1
B
9U-6862 Tapered Brush 1
9U-6863 Small Bore Brush 1
9U-7244 End Brush 1
9U-7237 Brush Extension 1
4C-5552 Large Bore Brush 1
C 4C-9507 Retaining Compound -
Start By:
a. Remove the electronic unit injectors.
1. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change"
for the correct draining and filling procedures.
1/4
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01261663
2. Install Tooling (A) into electronic unit injector sleeve (1).
3. Tighten the nut until electronic unit injector sleeve (1) is pulled free of the cylinder head
assembly.
Illustration 2 g01860393
4. Remove electronic unit injector sleeve (1).
Installation Procedure
1. Use Tooling (B) to clean the bore in the cylinder head for the electronic unit injector sleeve.
NOTICE
Ensure that the electronic unit injector sleeve and the cylinder head
bore are completely free of oil, dirt, and sealant debris.
2/4
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01261773
2. Install new O-ring seals (2) and (3) on electronic unit injector sleeve (1).
Note: Do not apply Tooling (C) to the cylinder head surfaces. Apply Tooling (C) on the
electronic unit injector sleeve only.
3. Apply a thin coat of Tooling (C) to O-ring seal (3) and the contact surface of electronic unit
injector sleeve (1) on the surface that is Marked "X".
Illustration 4 g01261802
4. Install Tooling (A) into the threads of electronic unit injector sleeve (1).
5. Position Tooling (A) and the electronic unit injector sleeve in the cylinder head. Use care
not to damage the O-ring seal on the electronic unit injector sleeve.
NOTICE
3/4
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Ensure that the electronic unit injector sleeve is properly seated in the
cylinder head. The Tooling will "RING" when the electronic unit
injector sleeve is fully seated in the bore of the cylinder head.
6. Use Tooling (A) and a hammer to install electronic unit injector sleeve (1) in the cylinder
head.
7. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change"
for the correct draining and filling procedures.
End By:
a. Install the electronic unit injectors.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 22:04:26 UTC+0800 2020
4/4
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR ETC
Configuration: 349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13
Engines for Caterpillar Built Machines
Media Number -KENR8150-05 Publication Date -01/01/2014 Date Updated -22/01/2014
i03589042
Air Cleaner - Remove and Install
SMCS - 1051-010-HG
Removal Procedure
Illustration 1 g01916039
1. Remove cover (1), primary filter element (2), and secondary filter element (3) from air
cleaner housing (4).
1/3
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g01916073
2. Attach a suitable lifting device to bracket (6) and air cleaner (4). The weight of bracket (6)
and air cleaner (4) is approximately 43 kg (95 lb).
3. Remove bolts (5).
Illustration 3 g01916113
4. Remove bolts (7). Remove bracket (6).
Illustration 4 g01916041
5. Remove bolts (9). Remove air filter housing (8) from bracket (6).
2/3
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Installation Procedure
1. Install air filter housing (8) in reverse order of removal.
a. Tighten bolts (9) to a torque of 17 ± 2 N·m (150 ± 18 lb in).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 22:05:22 UTC+0800 2020
3/3
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR ETC
Configuration: 349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13
Engines for Caterpillar Built Machines
Media Number -KENR8150-05 Publication Date -01/01/2014 Date Updated -22/01/2014
i04292173
Turbocharger - Remove and Install
SMCS - 1052-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description QTY
A 4C-5599 Anti-Seize Compound 1
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for more
information.
Illustration 1 g02170055
2. Disconnect clamp assembly (2) in order to separate adaptor (1) from the turbocharger.
1/3
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 3. Disconnect tube assemblies (3) and (4) .
Illustration 2 g01864534
4. Disconnect hose assemblies (5) and (7) .
5. Disconnect tube assembly (6) .
6. Attach a suitable lifting device to turbocharger (8) . The weight of turbocharger (8) is
approximately 26 kg (57 lb). Remove nuts (9) and turbocharger (8) . Remove the gasket and
discard nuts (9) .
Illustration 3 g02225358
7. If needed, carefully remove clamp assemblies (2) and (10) . Discard the clamp assemblies.
Installation Procedure
1. Install turbocharger (8) in reverse order of removal.
a. Tighten new clamp assemblies (2) to a torque of 12 ± 4 N·m (106 ± 35 lb in).
b. Tighten new clamp assemblies (10) to a torque of 13.6 ± 1.2 N·m (120 ± 11 lb in).
2/3
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. c. Apply Tooling (A) to the threads of new nuts (9) prior to installation. Tighten nuts (9)
to a torque of 70 ± 5 N·m (52 ± 4 lb ft).
d. Put clean engine oil in the oil inlet of the turbocharger after assembly or before
installation. This action will provide lubrication during start-up and during storage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 22:06:17 UTC+0800 2020
3/3
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR ETC
Configuration: 349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13
Engines for Caterpillar Built Machines
Media Number -KENR8150-05 Publication Date -01/01/2014 Date Updated -22/01/2014
i04141424
Solenoid Valve (Exhaust Balance) - Remove and Install
SMCS - 1052-010-VL
Removal Procedure
Illustration 1 g02339283
Overhead view showing the location of the solenoid valve.
1. Disconnect hose assembly (1) and disconnect tube assembly (5) .
2. Disconnect harness assembly (3) .
3. Remove bolt (2) and remove solenoid valve (4) .
Installation Procedure
1. Install the solenoid valve (4) in the reverse order.
1/2
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR ETC
Configuration: 349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13
Engines for Caterpillar Built Machines
Media Number -KENR8150-05 Publication Date -01/01/2014 Date Updated -22/01/2014
i03545920
Exhaust Sensor Lines - Remove and Install - Venturi
SMCS - 1923-IL
Removal Procedure
Illustration 1 g01873368
1. Disconnect harness assemblies (1).
2. Remove clamps (3) and (3).
3. Remove tube assembly (4).
4. Remove hose (3).
1/2
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01873370
5. Remove bolts (7).
6. Remove clamp (6) and venturi (8).
Illustration 3 g01873435
7. Remove bolts (10) and differential pressure sensor (9). Remove pressure sensor (11).
Installation Procedure
1. Install the exhaust sensor lines in reverse order of removal.
a. Tighten (11) to a torque of 10 ± 2 N·m (89 ± 18 lb in).
b. Tighten clamps (3) and (6) to a torque of 8.5 ± 2 N·m (75 ± 18 lb in).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 22:08:09 UTC+0800 2020
2/2
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR ETC
Configuration: 349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13
Engines for Caterpillar Built Machines
Media Number -KENR8150-05 Publication Date -01/01/2014 Date Updated -22/01/2014
i04140431
Air Control Valve - Remove and Install - Control Module,
Clean Emissions Module
SMCS - 108A-010
Removal Procedure
Illustration 1 g02338496
View of the Clean Emissions Module
1. Disconnect harness assembly (3). Remove bolts (1) and remove control module (2).
Installation Procedure
1. Install control module (2) in the reverse order.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 22:09:05 UTC+0800 2020
1/1
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR ETC
Configuration: 349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13
Engines for Caterpillar Built Machines
Media Number -KENR8150-05 Publication Date -01/01/2014 Date Updated -22/01/2014
i03571267
Air Control Valve - Remove and Install - ARD Combustion,
Clean Emissions Module
SMCS - 108A-010
Removal Procedure
Illustration 1 g02323318
1. Loosen clamp assemblies (2) and disconnect hose assembly (1).
2. Disconnect tube assembly (3) and disconnect hose assembly (4).
1/2
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g02323360
3. Disconnect harness assembly (7).
4. Remove bolts (5) and remove air control valve (6).
Illustration 3 g02323873
Typical Example
5. Remove bolts (12). Separate housings (11) and (8) from the air control valve actuator (9).
Remove both seals (10) from the housings.
Installation Procedure
1. Install the air control valve in the reverse order.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 22:10:00 UTC+0800 2020
2/2
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR ETC
Configuration: 349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13
Engines for Caterpillar Built Machines
Media Number -KENR8150-05 Publication Date -01/01/2014 Date Updated -22/01/2014
i03546101
Exhaust Gas Valve (NRS) - Remove and Install
SMCS - 108N-010; 5510
Removal Procedure
Start By:
a. Remove the venturi.
Illustration 1 g01873779
1. Disconnect harness assemblies (1) and tube assembly (2).
2. Disconnect hose assembly (3).
1/2
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g01873814
3. Loosen clamp (4). Remove bolts (5) and exhaust control valve (6).
Installation Procedure
1. Install exhaust control valve (6) in reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 22:10:56 UTC+0800 2020
2/2
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR ETC
Configuration: 349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13
Engines for Caterpillar Built Machines
Media Number -KENR8150-05 Publication Date -01/01/2014 Date Updated -22/01/2014
i03546401
Exhaust Gas Valve (NRS) - Disassemble
SMCS - 108N-015; 5510
Disassembly Procedure
Start By:
a. Remove the exhaust gas valve.
Illustration 1 g02173623
1. Remove temperature sensor (1).
2. Remove bolts (2). Separate actuator assembly (3) from valve housing (4).
1/2
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 2 g01845473
3. Remove nut (8), washer (7), and solenoid (6).
4. Remove spool (5).
Illustration 3 g02173629
5. Remove O-rings (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 22:11:52 UTC+0800 2020
2/2
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR ETC
Configuration: 349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13
Engines for Caterpillar Built Machines
Media Number -KENR8150-05 Publication Date -01/01/2014 Date Updated -22/01/2014
i03546406
Exhaust Gas Valve (NRS) - Assemble
SMCS - 108N-016; 5510
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3931 Anti-Seize Compound −
B 1P-0808 Multipurpose Grease −
Illustration 1 g02173629
Note: Lubricate all of the O-ring seals with the lubricant that is being sealed.
1. Install O-ring seals (9).
1/3
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 2 g01845473
2. Install spool (5). Tighten spool (5) to a torque of 50 ± 5 N·m (37 ± 4 lb ft).
3. Install solenoid (6), washer (7), and nut (8). Tighten nut (8) to a torque of 20 ± 2.5 N·m
(177 ± 22 lb in) .
Illustration 3 g01871983
4. Fill Cavity (B) with Tooling (B). Cavity (B) is found on the valve housing.
Illustration 4 g02173623
5. Install actuator assembly (3) on valve housing (4).
2/3
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 6. Apply Tooling (A) to the threads on temperature sensor (1). Tighten temperature sensor (1)
to a torque of 45 ± 5 N·m (33 ± 4 lb ft).
End By:
a. Install the exhaust control valve.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 14 22:12:48 UTC+0800 2020
3/3
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR ETC
Configuration: 349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13
Engines for Caterpillar Built Machines
Media Number -KENR8150-05 Publication Date -01/01/2014 Date Updated -22/01/2014
i03569679
Ignition Coil - Remove and Install - Clean Emissions Module
SMCS - 1554-010
Removal Procedure
Illustration 1 g02322433
1. Remove bolt (1) which secures the ground wire. Disconnect cable assembly (2).
2. Disconnect harness assembly (3).
1/2
349E L & 349E L-VG Excavators ETC00001-UP (MACHINE) POWERED BY C13 ...
2020/9/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...