This document provides instructions for removing and installing a water pump on a 349E L excavator. The removal procedure involves: 1) Removing the water temperature regulator and fan drive; 2) Removing various sheet assemblies and supports; 3) Disconnecting support assemblies and repositioning harness assemblies; 4) Removing hoses. The installation procedure involves reversing the removal steps and applying threadlock to bolts.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists 43 steps to assemble the various components of the torque converter in the correct order. Safety precautions are provided at the beginning regarding lifting heavy components and containing fluids. Diagrams illustrate each step. The summary ends by stating to connect the assembled torque converter housing to the planetary transmission.
Caterpillar cat 963 b track loader (prefix 9bl) service repair manual (9bl000...ujdjfjjskekmm
The document provides instructions for disassembling and assembling the air suspension system on a Caterpillar 963B track loader seat. It describes 22 steps to disassemble parts like the air spring, indicator, adjustment knob, and compressor. It then describes 19 steps to reassemble these parts in reverse order. Diagrams are provided to illustrate each step. Safety notices advise releasing air pressure before disassembly and wearing protective equipment when working with springs.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 345 c l hydraulic excavator (prefix pjw) service repair manua...hhfjksekmm
The document provides assembly instructions for a 345C excavator final drive system in 3 steps:
1. Adjust the bearing preload of the final drive by measuring dimensions and determining the correct shim thickness.
2. Assemble the carrier assemblies, which include installing planetary gears, bearings, shafts, and pins into housings.
3. Install the assembled carrier assemblies into the sprocket and ring gears in the correct order.
Caterpillar cat 319 d l excavator (prefix zca) service repair manual (zca0000...fjkskedmme
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 37 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is important throughout the process. The completed final drive and sprocket assembly weighs approximately 310 kg.
Caterpillar cat 319 d l excavator (prefix kfm) service repair manual (kfm0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component. Some key steps in the disassembly include removing the cover, carrier assembly, ring gears, and separating internal planetary gears. Assembly involves installing bearings in the main housing, determining the correct shim thickness, installing seals, and reassembling internal components along with aligning the main housing to the motor housing. The instructions are detailed with illustrations and require specialized tools.
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar cat 345 d l excavator (prefix jkn) service repair manual (jkn0000...hhfjksekmm
The document provides instructions for assembling a travel motor. It describes 33 steps to assemble parts like pistons, seals, plates, springs and valves. Measurements are checked with tools at several steps to ensure correct assembly. Cleaning parts and preventing contamination of hydraulic systems is emphasized.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists 43 steps to assemble the various components of the torque converter in the correct order. Safety precautions are provided at the beginning regarding lifting heavy components and containing fluids. Diagrams illustrate each step. The summary ends by stating to connect the assembled torque converter housing to the planetary transmission.
Caterpillar cat 963 b track loader (prefix 9bl) service repair manual (9bl000...ujdjfjjskekmm
The document provides instructions for disassembling and assembling the air suspension system on a Caterpillar 963B track loader seat. It describes 22 steps to disassemble parts like the air spring, indicator, adjustment knob, and compressor. It then describes 19 steps to reassemble these parts in reverse order. Diagrams are provided to illustrate each step. Safety notices advise releasing air pressure before disassembly and wearing protective equipment when working with springs.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 345 c l hydraulic excavator (prefix pjw) service repair manua...hhfjksekmm
The document provides assembly instructions for a 345C excavator final drive system in 3 steps:
1. Adjust the bearing preload of the final drive by measuring dimensions and determining the correct shim thickness.
2. Assemble the carrier assemblies, which include installing planetary gears, bearings, shafts, and pins into housings.
3. Install the assembled carrier assemblies into the sprocket and ring gears in the correct order.
Caterpillar cat 319 d l excavator (prefix zca) service repair manual (zca0000...fjkskedmme
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 37 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is important throughout the process. The completed final drive and sprocket assembly weighs approximately 310 kg.
Caterpillar cat 319 d l excavator (prefix kfm) service repair manual (kfm0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component. Some key steps in the disassembly include removing the cover, carrier assembly, ring gears, and separating internal planetary gears. Assembly involves installing bearings in the main housing, determining the correct shim thickness, installing seals, and reassembling internal components along with aligning the main housing to the motor housing. The instructions are detailed with illustrations and require specialized tools.
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar cat 345 d l excavator (prefix jkn) service repair manual (jkn0000...hhfjksekmm
The document provides instructions for assembling a travel motor. It describes 33 steps to assemble parts like pistons, seals, plates, springs and valves. Measurements are checked with tools at several steps to ensure correct assembly. Cleaning parts and preventing contamination of hydraulic systems is emphasized.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 140 m 3 awd motor grader (prefix n9j) service repair manual (...ufjjsejfkskemme
This document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal process involves:
1. Removing the rear chassis support to access the pump.
2. Disconnecting hydraulic hoses and electrical harnesses from the pump.
3. Using lifting equipment to remove the 52 kg pump from the grader.
Reinstallation is the reverse of removal, including reconnecting hoses and harnesses and securing the pump with bolts. Proper cleaning and replacement of O-rings is emphasized to prevent contamination.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 349 f lxe excavator (prefix rax) service repair manual (rax00...fjsjjekdkme
The document provides instructions for disassembling and assembling the final drive of a 349F LXE excavator. The disassembly procedure involves removing 33 parts from the final drive including the ring gear, carrier assembly, planetary gears, and seals. The assembly procedure instructs installing 52 parts in the reverse order and specifies torque specifications and lubricants to apply during assembly. Tools required include lifting devices, punches, and seal installation tools.
Caterpillar cat 730 c articulated truck (prefix tff) service repair manual (t...ufjjsekkemmd
The document provides instructions for disassembling and assembling the torque converter of a 730C articulated truck. It lists 18 steps for disassembly, which include removing housing assemblies, bearings, plates, discs, seals and other internal components. It then lists 15 steps for assembly, which describe installing components in reverse order and include details on tooling used and proper torque specifications. The instructions note to keep parts clean from contaminants to prevent wear and shortened life.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsjeskkekem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fuusejkddmmd3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujsekmd9idd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...shibi1322
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...fucheng89
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdksmmdmdd
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdkskmmdd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...8foskkdjdkdm3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...jiazhi27185
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujkse9didkke3
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...didkkskdmmd
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...km7seyrduhdw
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...yin9niaojiao
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 140 m 3 awd motor grader (prefix n9j) service repair manual (...ufjjsejfkskemme
This document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal process involves:
1. Removing the rear chassis support to access the pump.
2. Disconnecting hydraulic hoses and electrical harnesses from the pump.
3. Using lifting equipment to remove the 52 kg pump from the grader.
Reinstallation is the reverse of removal, including reconnecting hoses and harnesses and securing the pump with bolts. Proper cleaning and replacement of O-rings is emphasized to prevent contamination.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 349 f lxe excavator (prefix rax) service repair manual (rax00...fjsjjekdkme
The document provides instructions for disassembling and assembling the final drive of a 349F LXE excavator. The disassembly procedure involves removing 33 parts from the final drive including the ring gear, carrier assembly, planetary gears, and seals. The assembly procedure instructs installing 52 parts in the reverse order and specifies torque specifications and lubricants to apply during assembly. Tools required include lifting devices, punches, and seal installation tools.
Caterpillar cat 730 c articulated truck (prefix tff) service repair manual (t...ufjjsekkemmd
The document provides instructions for disassembling and assembling the torque converter of a 730C articulated truck. It lists 18 steps for disassembly, which include removing housing assemblies, bearings, plates, discs, seals and other internal components. It then lists 15 steps for assembly, which describe installing components in reverse order and include details on tooling used and proper torque specifications. The instructions note to keep parts clean from contaminants to prevent wear and shortened life.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsjeskkekem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fuusejkddmmd3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujsekmd9idd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...shibi1322
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...fucheng89
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdksmmdmdd
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdkskmmdd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...8foskkdjdkdm3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...jiazhi27185
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujkse9didkke3
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...didkkskdmmd
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...km7seyrduhdw
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...yin9niaojiao
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...orrf0370383
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...fjskekxcddmmme
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...cdsaas
The document provides instructions for assembling a travel motor. It describes 33 steps for installing various components like seals, pistons, plates, and bearings. Measurements are taken throughout to ensure proper assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The travel motor must be filled with the correct oil type before operation to prevent damage.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...hhfjksekmm
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
Caterpillar cat 349 d l excavator (prefix gkf) service repair manual (gkf0000...fjjseksxckmdme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions to contain fluids. The procedure describes attaching a lifting device to the travel motor and removing bolts and hose assemblies to detach the travel motor from the excavator.
Similar to Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz00001 and up) (19)
Kawasaki 80 z6 wheel loader parts catalogue manual (serial no. 80c7 0101 and up)hhfjksekmm
This document is a parts catalog for a Hitachi wheel loader powered by a Cummins QSB6.7 engine. It contains a table of contents listing the major systems of the loader and their corresponding parts sections. These include the engine, powertrain, chassis, cab, electrical systems, hydraulics, brakes, and controls. Each part is assigned a unique identification number and name in the catalog for ordering purposes.
Kawasaki 70 z7b wheel loader service repair manual (serial no. 70c6 5001 and up)hhfjksekmm
This document provides disassembly and assembly instructions for removing and installing the cab on a wheel loader. It outlines 14 steps including draining fluids, releasing pressures, removing bolts and covers. Precautions are provided regarding escaping fluids, capping open lines, and ensuring pressures are released from the hydraulic and other systems. The document contains diagrams illustrating the specific components and their locations.
Caterpillar cat 325 l excavator (prefix 7lm) service repair manual (7lm00001 ...hhfjksekmm
This document provides instructions for disassembling the travel motor on 325, 325B, and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Special markings and care are required to keep components in their original positions for reassembly.
Caterpillar cat 325 a fm l excavator (prefix 7 lm) service repair manual (7lm...hhfjksekmm
This document provides instructions for disassembling a travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, identifying each component and how to remove it. This includes removing the head, brake piston, barrel assembly, shoe retainer, springs and other internal components. Special tools may be required and precautions around containing fluids are noted. The process is similar between 325 and 325B excavator models, with some weight and bolt quantity differences called out.
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...hhfjksekmm
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, valves, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers to separate the motor head assembly, rotating group, and individual internal parts in a safe manner while taking precautions for any released spring forces.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...hhfjksekmm
The document provides instructions for removing and installing various engine components on a Caterpillar 349E L excavator, including:
1) Removing and installing electronic unit injector sleeves, which requires using specialized tools to pull the sleeves from the cylinder head and reinstall them with new O-rings.
2) Procedures for removing and installing the air cleaner housing, turbocharger, exhaust balance solenoid valve, and exhaust sensor lines.
3) Detailed illustrations and torque specifications are provided for correctly performing each removal and installation step. Proper cleaning and use of new sealing components is emphasized.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...hhfjksekmm
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...hhfjksekmm
The document provides instructions to disassemble and assemble the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, ring gear, carrier assembly, planetary gears, and seals. It then describes the assembly process, providing specifications for torque and installation of components like bolts, bearings, seals, and shims. Proper cleaning and use of locking compounds or lubricants is emphasized to ensure correct assembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...hhfjksekmm
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing over 20 components including bolts, seals, retainers, discs, and housing assemblies.
3) Assembly is the reverse of disassembly, requiring pressing or installing components like bearings, seals, sleeves and housings back into place and securing with bolts, pins or retaining rings. Cleanliness and use of specified tools and adhesives is important for successful reassembly.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...hhfjksekmm
The document provides instructions for disassembling and assembling the travel motor of a 349E excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order, like installing seals, pins, bearings onto the shaft assembly before pressing it into the motor housing. Tolerances and specifications are provided for components like springs, seals, and fasteners.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly process describes 13 steps and specifications to reinstall components in the reverse order, ensuring proper torque values and lubrication of parts. Key components include the motor housing, head assembly, shaft assembly, barrel assembly, pistons, bearings, seals, springs, and related hardware.
Caterpillar cat 349 e l excavator (prefix mzw) service repair manual (mzw0000...hhfjksekmm
This document provides assembly instructions for a 349E L excavator final drive group. It includes specifications for the components and a step-by-step procedure for assembling the final drive. Some key steps include applying anti-seize compound to bearings, using shims to adjust clearances, and torquing bolts to the specified values. Tools required include a transmission repair stand, eyebolts, and torque wrenches. The assembly procedure has 30 steps and ensures the final drive is properly assembled and adjusted.
Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx0000...hhfjksekmm
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
Caterpillar cat 349 e l excavator (prefix fjb) service repair manual (fjb0000...hhfjksekmm
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. It describes 22 steps to disassemble the components, including removing bolts, retainers, seals, discs, and housing parts. It then describes 14 steps for reassembling the components, applying sealant and installing seals, sleeves, bearings and housing pieces in the reverse order of disassembly. Precision cleaning and special tools are required to prevent damage to parts during the process.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...hhfjksekmm
The document provides instructions for removing and installing various engine components on a Caterpillar 349E L excavator, including:
1) Removing and installing electronic unit injector sleeves, which requires using specialized tools to pull the sleeves from the cylinder head and clean the bore before reinstalling with new O-rings.
2) Procedures for removing and installing the air cleaner housing, turbocharger, exhaust balance solenoid valve, and exhaust sensor lines.
3) Detailed illustrations and torque specifications are provided for correctly performing each removal and installation step.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...hhfjksekmm
The document provides instructions to disassemble and assemble the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive by removing components like the coupling, cover, ring gear, carrier assembly, planetary gears, and seals. It then describes the assembly process in reverse, providing specifications for torque and application of sealants or lubricants during reassembly. Precise alignment and orientation of parts is emphasized to ensure proper reassembly.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i06192451
Fan Drive - Assemble - Hydraulic Fan Drive
SMCS - 1359-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1861 Retaining Ring Pliers 1
B 9U-7480 Compressing Tube 1
C 1P-1859 Retaining Ring Pliers 1
D 1P-1863 Retaining Ring Pliers 1
E - Loctite Flexible Anaerobic Gasket Flange 1
F - Loctite 648 1
G 359-4915 Driver 1
H 359-4916 Driver 1
Note: Caution is required while handling the lip seals. The lip seals can be damaged if objects or
cleaning fluids contact the sealing surface.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts except the lip
seals with cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to
dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
1/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01333314
1. Use a suitable press to install bearing (29) into case (9) . Use Tooling (A) in order to install
retaining ring (28) .
Illustration 2 g01333310
Note: Caution is required while handling the lip seals. The lip seals can be damaged if
objects or cleaning fluids contact the sealing surface.
2. Apply Tooling (E) to the outside diameter of lip seal (27) . Carefully install lip seal (27) into
case (9) .
2/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g02092525
3. Install seal (25) onto shaft assembly (24) .
4. Apply Tooling (F) to the full diameter of the shoulder on shaft assembly (24) . Position new
sleeve (30) on shaft assembly (24) . The external chamfer on sleeve (30) will be on top. Use
Tooling (G) and a suitable press in order to install sleeve (30) . Remove excess Tooling (F) .
Illustration 4 g01333308
Illustration 5 g01286111
3/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Position tube assembly (26) into case (9) .
6. Position case (9) and tube assembly (26) onto shaft assembly (24) .
7. Use a suitable press and a suitable driver to press shaft assembly (24) through the bearing
and through tube assembly (26) .
Illustration 6 g01333303
8. Use Tooling (D) in order to install retaining ring (23) . Install seal rings (22) onto shaft
assembly (24) .
Illustration 7 g01333301
9. Install spring (21) on clutch housing assembly (11) .
4/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g01333300
10. Install seal (20) on piston (18) .
Illustration 9 g01333298
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
11. Install piston (18) . Use Tooling (B) and a suitable press in order to position piston (18) .
Use Tooling (C) in order to install retaining ring (19) . Carefully release the tension on
Tooling (B) .
5/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g01208920
12. Install clutch plates (16) and discs (17) . Install retaining ring (15) .
Illustration 11 g01209073
13. Position cover assembly (8) onto clutch housing assembly (11) .
Note: Make sure that the splines of cover assembly (8) fully engage all of the clutch plates
and discs in the clutch assembly.
6/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g01209125
Illustration 13 g01258534
Note: Caution is required while handling the lip seals. The lip seals can be damaged if
objects or cleaning fluids contact the sealing surface.
14. Use a suitable press in order to install bearing (14) . Use Tooling (A) in order to install
retaining ring (13) . Install lip seal (12) .
Illustration 14 g01333297
15. Position cover assembly (8) on the opposite side.
16. Install O-ring seal (10) on cover assembly (8) .
7/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g01208914
17. Position cover assembly (8) onto case (9) . Install bolts (7) and tighten bolts (7) to a
minimum torque of 18 N·m (13 lb ft) up to a maximum torque of 31 N·m (23 lb ft).
Illustration 16 g02092935
18. Apply Tooling (F) to the full diameter of the shoulder on drive flange (6) . Position new
sleeve (6A) on drive flange (6) . The external chamfer on sleeve (6A) will be on top. Use
Tooling (H) and a suitable press in order to install sleeve (6A) . Remove excess Tooling
(F) .
8/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g01333295
19. Install drive flange (6) and O-ring seal (5) .
Illustration 18 g01333292
20. Install retainer (4) . Tighten retainer (4) to a minimum torque of 610 N·m (450 lb ft) up to a
maximum torque of 750 N·m (550 lb ft). After achieving the torque range, overtighten
retainer (4) as needed in order to align the next position for locking screws (3) .
21. Install locking screws (3) and tighten locking screws (3) to a minimum torque of 7 N·m (62
lb in) to a maximum torque of 10 N·m (89 lb in).
9/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g01208862
22. Position sensor (1) . Install bolt (2) .
End By: Install the fan clutch. Refer to Disassembly and Assembly, "Fan Clutch - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:21:39 UTC+0800 2020
10/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04142231
Fan Drive - Assemble - Direct Drive
SMCS - 1359-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Illustration 1 g02341528
1. Install spring pin (6) into plate (7) .
2. Apply Tooling (A) to the threads of bolt (8). Install bearing assembly (2), spacer (3), hub
assembly (4), bearing assembly (5), plate (7), and bolt (8) onto bracket assembly (1).
Tighten bolt (8) to a torque of 115 ± 15 N·m (85 ± 11 lb ft).
1/2
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. End By: Install the fan drive (direct drive).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:22:35 UTC+0800 2020
2/2
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04108512
Water Pump - Remove and Install
SMCS - 1361-010; 1361-011; 1361-012
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Start By:
A. Remove the water temperature regulator.
B. Remove fan drive.
Illustration 1 g02310883
1/4
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 1. Remove bolts (1) and sheet assembly (2). Remove bolts (3) and sheet assembly (4) .
Illustration 2 g02311921
2. Remove step (6), sheet assembly (5), sheet assembly (7), and sheet assembly (8) .
Illustration 3 g02311923
Note: Open the hoods to the FULLY OPEN position.
3. Disconnect support assembly (9). Use suitable cribbing to support the support assembly (9) .
4. Remove support assembly (10) and support assembly (11) .
2/4
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g02311924
Note: Keep a minimum diameter bend of 102 mm (4.0 inch) for harness assemblies (13) .
5. Remove sheet assembly (15) and sheet assembly (16). Reposition sheet assembly (12) .
6. Remove hose (14) .
Illustration 5 g02311973
Illustration 6 g02311974
3/4
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 7. Remove bracket (14), tube (19), and elbow assembly (20) .
8. Remove bolts (22), water pump (21), and the O-ring seal.
Installation Procedure
1. Install water pump (21) in the reverse order of removal.
a. Lubricate the bore for the water pump (21) with lubricant that is being sealed.
b. Apply Tooling (A) to the threads of bolts (1) and (3) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:23:31 UTC+0800 2020
4/4
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04137389
Crankshaft Vibration Damper and Pulley - Remove and
Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2712 Guide Stud 2
Start By:
A. Remove the fan drive.
Illustration 1 g02334917
1/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 1. Remove bolts (2) and support (1). Disconnect bracket (3) .
Illustration 2 g02334920
2. Remove belt (4). Refer to the Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
3. Use two people to remove bracket assembly (6). The weight of bracket assembly (6) is
approximately 28 kg (62 lb). Remove bolts (5) and bracket assembly (6) .
Illustration 3 g02334921
4. Remove two bolts (9). Install Tooling (A).
5. Remove the remaining bolts (9). Remove pulley (11), adapter (10), pulley (8), and damper
assembly (7).
Installation Procedure
1. Install the crankshaft vibration damper and pulley in the reverse order of removal procedure.
Wed Sep 16 18:24:27 UTC+0800 2020
2/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04109121
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Start By:
A. Remove the crankshaft vibration damper and pulley.
Illustration 1 g01870637
Typical Example
1. Remove nuts (1) and crankshaft front seal (2) .
Installation Procedure
1. Install crankshaft front seal (2) in reverse order of removal.
1/2
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Note: Leave the shipping sleeve in place in order to install the crankshaft front seal. The
crankshaft front seal must be installed dry.
Illustration 2 g01870695
a. Tighten nuts (1) in a numerical sequence.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:25:22 UTC+0800 2020
2/2
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04109500
Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
1. Refer to Operation and Maintenance Manual, "Engine Oil and Oil Filter - Change" for the
correct draining and filling procedures.
1/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 1 g02312593
2. Remove bolts (1) and plate assemblies (4).
3. Remove bolts (2) and plate assembly (3) .
Illustration 2 g02312754
4. Disconnect clips (5) and (6) .
Illustration 3 g02312755
2/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 5. Disconnect harness assembly (7). Disconnect hose assembly (10).
6. Remove bolts (8) and lower engine oil pan (9) .
Illustration 4 g02312836
7. Remove bolts (11), bolts (13), and tube assembly (12).
8. Remove engine oil pan (9) .
Installation Procedure
1. Install engine oil pan (9) in reverse order of the removal.
a. Apply Tooling (A) to the threads of bolts (1) and (2) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:26:18 UTC+0800 2020
3/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04142771
Engine Front Mount - Remove and Install
SMCS - 1152-FR
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Personal injury can result from hot coolant, steam and alkali.
At operating temperature, engine coolant is hot and under pressure.
The radiator and all lines to heaters or the engine contain hot coolant or
steam. Any contact can cause severe burns.
Remove cooling system pressure cap slowly to relieve pressure only
when engine is stopped and cooling system pressure cap is cool enough
to touch with your bare hand.
Do not attempt to tighten hose connections when the coolant is hot, the
hose can come off causing burns.
Cooling System Coolant Additive contains alkali. Avoid contact with
skin and eyes.
1/7
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...