This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f l excavator (prefix hlb) service repair manual (hlb0000...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix hpd) service repair manual (hpd00001 ...fjsjjekdkme
The document provides instructions to disassemble a travel motor over 27 steps. It begins by draining the motor and removing external components like plugs, seals, and the motor head assembly. Internally, it describes removing the barrel assembly, piston assemblies, separator and friction plates, springs, and swashplate. Safety notices are provided throughout to warn of potential spring hazards and to mark components for proper reassembly.
Caterpillar cat 349 f l excavator (prefix kea) service repair manual (kea0000...fjjskekdmme
The document provides instructions for disassembling and assembling the travel motor of a 349F L excavator. It describes 31 steps to disassemble the travel motor by removing components like plugs, springs, pistons, and bearings. It then describes 28 steps to reassemble the travel motor by reversing the disassembly steps and ensuring components like seals, pins, and bearings are properly installed using the specified tools and torques. Safety notices are included throughout to warn of potential injury from released springs or flying parts during disassembly and assembly.
Caterpillar cat 349 d l mobile hydraulic excavator (prefix dkn) service repai...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like the displacement change valve and head. Internal components like the brake piston, disks, and rotating group are then removed. Individual parts in the rotating group like the piston assemblies and barrel are also taken apart. The assembly instructions reverse the disassembly process and provide details on cleaning, lubricating, and installing parts in their proper positions and with the correct torque specifications.
Caterpillar cat 349 f l excavator (prefix wna) service repair manual (wna0000...fjjskekdmme
The document provides instructions for disassembling and assembling the travel motor of a 349F L and 352F excavator. It begins by describing the required tools and safety precautions. The 32-step disassembly procedure removes components like plugs, springs, pistons, and bearings. The assembly section provides specifications, required tools, and a 28-step procedure to reinstall components in reverse order. Precautions are given to lubricate parts and apply locking agents in correct locations.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar cat 345 c l hydraulic excavator (prefix pjw) service repair manua...hhfjksekmm
The document provides assembly instructions for a 345C excavator final drive system in 3 steps:
1. Adjust the bearing preload of the final drive by measuring dimensions and determining the correct shim thickness.
2. Assemble the carrier assemblies, which include installing planetary gears, bearings, shafts, and pins into housings.
3. Install the assembled carrier assemblies into the sprocket and ring gears in the correct order.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...cdsaas
The document provides instructions for disassembling and assembling the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 f l excavator (prefix hlb) service repair manual (hlb0000...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix hpd) service repair manual (hpd00001 ...fjsjjekdkme
The document provides instructions to disassemble a travel motor over 27 steps. It begins by draining the motor and removing external components like plugs, seals, and the motor head assembly. Internally, it describes removing the barrel assembly, piston assemblies, separator and friction plates, springs, and swashplate. Safety notices are provided throughout to warn of potential spring hazards and to mark components for proper reassembly.
Caterpillar cat 349 f l excavator (prefix kea) service repair manual (kea0000...fjjskekdmme
The document provides instructions for disassembling and assembling the travel motor of a 349F L excavator. It describes 31 steps to disassemble the travel motor by removing components like plugs, springs, pistons, and bearings. It then describes 28 steps to reassemble the travel motor by reversing the disassembly steps and ensuring components like seals, pins, and bearings are properly installed using the specified tools and torques. Safety notices are included throughout to warn of potential injury from released springs or flying parts during disassembly and assembly.
Caterpillar cat 349 d l mobile hydraulic excavator (prefix dkn) service repai...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like the displacement change valve and head. Internal components like the brake piston, disks, and rotating group are then removed. Individual parts in the rotating group like the piston assemblies and barrel are also taken apart. The assembly instructions reverse the disassembly process and provide details on cleaning, lubricating, and installing parts in their proper positions and with the correct torque specifications.
Caterpillar cat 349 f l excavator (prefix wna) service repair manual (wna0000...fjjskekdmme
The document provides instructions for disassembling and assembling the travel motor of a 349F L and 352F excavator. It begins by describing the required tools and safety precautions. The 32-step disassembly procedure removes components like plugs, springs, pistons, and bearings. The assembly section provides specifications, required tools, and a 28-step procedure to reinstall components in reverse order. Precautions are given to lubricate parts and apply locking agents in correct locations.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar cat 345 c l hydraulic excavator (prefix pjw) service repair manua...hhfjksekmm
The document provides assembly instructions for a 345C excavator final drive system in 3 steps:
1. Adjust the bearing preload of the final drive by measuring dimensions and determining the correct shim thickness.
2. Assemble the carrier assemblies, which include installing planetary gears, bearings, shafts, and pins into housings.
3. Install the assembled carrier assemblies into the sprocket and ring gears in the correct order.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...cdsaas
The document provides instructions for disassembling and assembling the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the housing cover, carrier assemblies, planetary gear assemblies, ring gear, and motor housing. Precautions are given to ensure cleanliness during disassembly and assembly. The parts are to be reinstalled in their original locations and orientation marks should be made for alignment. Proper lifting devices and techniques are specified due to the heavy weights of some components.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 345 d l excavator (prefix pbt) service repair manual (pbt0000...hhfjksekmm
This document provides disassembly and assembly instructions for the swing drive of a 345D L excavator. It details 32 steps to disassemble the swing drive components including removing the carrier assembly, sun gear, ring gear, and bearings. It also lists the required tools. The assembly section notes the importance of cleanliness and lists 13 tools needed for reassembling the swing drive components.
Caterpillar cat 349 d excavator (prefix men) service repair manual (men00001 ...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 13 steps for assembly, including installing seals, spacers, pistons, housing, and tightening components. Required tools include eyebolts, pullers, drivers, and seals. Cleanliness is emphasized to prevent contamination of hydraulic components.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 430 e backhoe loader (prefix rln) service repair manual (rln0...fjjskekskemmm
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and describes removing components like gears, shafts, seals and sensors. Detailed illustrations accompany each step to show how to use tools to remove parts and access internal mechanisms. Cleanliness is stressed to prevent dirt entry during disassembly.
Caterpillar cat 349 d excavator (prefix nnf) service repair manual (nnf00001 ...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, disks, seals and more. It then lists 28 steps for assembly, installing components like seals, spacers, washers, pistons and plugs in the reverse order of disassembly. Precautions are provided to keep parts clean and properly identify components to ensure correct reassembly.
Caterpillar cat 349 f excavator (prefix tew) service repair manual (tew00001 ...fjsjjekdkme
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes removing over 30 components of the travel motor in sequential order, including plugs, springs, pistons, plates, seals, and more.
3. Precautions are provided to protect against spring forces and ensure components are reinstalled in their original positions and order.
Caterpillar cat 349 f l excavator (prefix tew) service repair manual (tew0000...fjjskmdmem
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes removing 32 components in 31 steps, taking precautions for spring forces.
3. Reassembly involves lubricating components and installing 28 parts in 28 steps, torquing bolts and plugs to specified values.
Caterpillar cat 349 f l excavator (prefix tew) service repair manual (tew0000...fjsjjekdkme
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavator models.
2. It details 31 steps for disassembly, removing components like plugs, springs, pistons, plates, and seals.
3. The assembly section lists specifications and torque values for reinstalling components and filling the case with clean hydraulic oil before operation.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavator models.
2. It details 31 steps for disassembly, removing components like plugs, springs, pistons, plates, and seals. Safety precautions are provided.
3. The assembly section lists specifications for components and the order for reinstalling parts like seals, springs, pistons, and covers. Lubrication and torque requirements are specified.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavator models.
2. It details 31 steps for disassembly, removing components like plugs, springs, pistons, plates, and seals. Safety precautions are provided.
3. The assembly section lists specifications for components and the order for reinstalling parts like seals, springs, pistons, and covers. Lubrication and torque requirements are specified.
Caterpillar cat 349 f excavator (prefix tew) service repair manual (tew00001 ...didkskdkmdm
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavator models.
2. It details 31 steps for disassembly, removing components like plugs, springs, pistons, plates, and seals. Safety precautions are provided.
3. The assembly section lists specifications for components and the order for reinstalling parts like seals, springs, pistons, and covers. Lubrication and torque requirements are specified.
Caterpillar cat 349 f excavator (prefix tew) service repair manual (tew00001 ...fjjskmdmem
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes removing over 30 components of the travel motor in sequential order, taking safety precautions for parts under spring pressure.
3. Specifications are provided for components, along with torque values and installation notes to ensure proper reassembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes removing over 30 components of the travel motor in sequential order, taking safety precautions for parts under spring pressure.
3. Specifications are provided for components, along with required tools and torque specifications for reassembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes 31 steps to disassemble the travel motor by removing components like plugs, springs, pistons, plates, seals and more.
3. It also lists 13 steps to reassemble the travel motor by installing components in the reverse order, and provides specifications and torque values for many parts. Personal protective equipment is recommended due to potential spring hazards.
Kawasaki 80 z6 wheel loader parts catalogue manual (serial no. 80c7 0101 and up)hhfjksekmm
This document is a parts catalog for a Hitachi wheel loader powered by a Cummins QSB6.7 engine. It contains a table of contents listing the major systems of the loader and their corresponding parts sections. These include the engine, powertrain, chassis, cab, electrical systems, hydraulics, brakes, and controls. Each part is assigned a unique identification number and name in the catalog for ordering purposes.
Kawasaki 70 z7b wheel loader service repair manual (serial no. 70c6 5001 and up)hhfjksekmm
This document provides disassembly and assembly instructions for removing and installing the cab on a wheel loader. It outlines 14 steps including draining fluids, releasing pressures, removing bolts and covers. Precautions are provided regarding escaping fluids, capping open lines, and ensuring pressures are released from the hydraulic and other systems. The document contains diagrams illustrating the specific components and their locations.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the housing cover, carrier assemblies, planetary gear assemblies, ring gear, and motor housing. Precautions are given to ensure cleanliness during disassembly and assembly. The parts are to be reinstalled in their original locations and orientation marks should be made for alignment. Proper lifting devices and techniques are specified due to the heavy weights of some components.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 345 d l excavator (prefix pbt) service repair manual (pbt0000...hhfjksekmm
This document provides disassembly and assembly instructions for the swing drive of a 345D L excavator. It details 32 steps to disassemble the swing drive components including removing the carrier assembly, sun gear, ring gear, and bearings. It also lists the required tools. The assembly section notes the importance of cleanliness and lists 13 tools needed for reassembling the swing drive components.
Caterpillar cat 349 d excavator (prefix men) service repair manual (men00001 ...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 13 steps for assembly, including installing seals, spacers, pistons, housing, and tightening components. Required tools include eyebolts, pullers, drivers, and seals. Cleanliness is emphasized to prevent contamination of hydraulic components.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 430 e backhoe loader (prefix rln) service repair manual (rln0...fjjskekskemmm
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It lists the required tools and describes removing components like gears, shafts, seals and sensors. Detailed illustrations accompany each step to show how to use tools to remove parts and access internal mechanisms. Cleanliness is stressed to prevent dirt entry during disassembly.
Caterpillar cat 349 d excavator (prefix nnf) service repair manual (nnf00001 ...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, disks, seals and more. It then lists 28 steps for assembly, installing components like seals, spacers, washers, pistons and plugs in the reverse order of disassembly. Precautions are provided to keep parts clean and properly identify components to ensure correct reassembly.
Caterpillar cat 349 f excavator (prefix tew) service repair manual (tew00001 ...fjsjjekdkme
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes removing over 30 components of the travel motor in sequential order, including plugs, springs, pistons, plates, seals, and more.
3. Precautions are provided to protect against spring forces and ensure components are reinstalled in their original positions and order.
Caterpillar cat 349 f l excavator (prefix tew) service repair manual (tew0000...fjjskmdmem
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes removing 32 components in 31 steps, taking precautions for spring forces.
3. Reassembly involves lubricating components and installing 28 parts in 28 steps, torquing bolts and plugs to specified values.
Caterpillar cat 349 f l excavator (prefix tew) service repair manual (tew0000...fjsjjekdkme
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavator models.
2. It details 31 steps for disassembly, removing components like plugs, springs, pistons, plates, and seals.
3. The assembly section lists specifications and torque values for reinstalling components and filling the case with clean hydraulic oil before operation.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavator models.
2. It details 31 steps for disassembly, removing components like plugs, springs, pistons, plates, and seals. Safety precautions are provided.
3. The assembly section lists specifications for components and the order for reinstalling parts like seals, springs, pistons, and covers. Lubrication and torque requirements are specified.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavator models.
2. It details 31 steps for disassembly, removing components like plugs, springs, pistons, plates, and seals. Safety precautions are provided.
3. The assembly section lists specifications for components and the order for reinstalling parts like seals, springs, pistons, and covers. Lubrication and torque requirements are specified.
Caterpillar cat 349 f excavator (prefix tew) service repair manual (tew00001 ...didkskdkmdm
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavator models.
2. It details 31 steps for disassembly, removing components like plugs, springs, pistons, plates, and seals. Safety precautions are provided.
3. The assembly section lists specifications for components and the order for reinstalling parts like seals, springs, pistons, and covers. Lubrication and torque requirements are specified.
Caterpillar cat 349 f excavator (prefix tew) service repair manual (tew00001 ...fjjskmdmem
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes removing over 30 components of the travel motor in sequential order, taking safety precautions for parts under spring pressure.
3. Specifications are provided for components, along with torque values and installation notes to ensure proper reassembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes removing over 30 components of the travel motor in sequential order, taking safety precautions for parts under spring pressure.
3. Specifications are provided for components, along with required tools and torque specifications for reassembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor on 349F and 349F L excavators.
2. It describes 31 steps to disassemble the travel motor by removing components like plugs, springs, pistons, plates, seals and more.
3. It also lists 13 steps to reassemble the travel motor by installing components in the reverse order, and provides specifications and torque values for many parts. Personal protective equipment is recommended due to potential spring hazards.
Similar to Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 and up) (9)
Kawasaki 80 z6 wheel loader parts catalogue manual (serial no. 80c7 0101 and up)hhfjksekmm
This document is a parts catalog for a Hitachi wheel loader powered by a Cummins QSB6.7 engine. It contains a table of contents listing the major systems of the loader and their corresponding parts sections. These include the engine, powertrain, chassis, cab, electrical systems, hydraulics, brakes, and controls. Each part is assigned a unique identification number and name in the catalog for ordering purposes.
Kawasaki 70 z7b wheel loader service repair manual (serial no. 70c6 5001 and up)hhfjksekmm
This document provides disassembly and assembly instructions for removing and installing the cab on a wheel loader. It outlines 14 steps including draining fluids, releasing pressures, removing bolts and covers. Precautions are provided regarding escaping fluids, capping open lines, and ensuring pressures are released from the hydraulic and other systems. The document contains diagrams illustrating the specific components and their locations.
Caterpillar cat 325 l excavator (prefix 7lm) service repair manual (7lm00001 ...hhfjksekmm
This document provides instructions for disassembling the travel motor on 325, 325B, and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, springs, and shaft. Special markings and care are required to keep components in their original positions for reassembly.
Caterpillar cat 325 a fm l excavator (prefix 7 lm) service repair manual (7lm...hhfjksekmm
This document provides instructions for disassembling a travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, identifying each component and how to remove it. This includes removing the head, brake piston, barrel assembly, shoe retainer, springs and other internal components. Special tools may be required and precautions around containing fluids are noted. The process is similar between 325 and 325B excavator models, with some weight and bolt quantity differences called out.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...hhfjksekmm
The document provides step-by-step instructions to disassemble a travel motor on a 349F and 349F L excavator. It describes 27 steps to remove components such as plugs, seals, springs, bearings, valves, and housing pieces. Various tools are required including lifting devices, bolts, nuts, and pullers to separate the motor head assembly, rotating group, and individual internal parts in a safe manner while taking precautions for any released spring forces.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...hhfjksekmm
The document provides instructions for removing and installing various engine components on a Caterpillar 349E L excavator, including:
1) Removing and installing electronic unit injector sleeves, which requires using specialized tools to pull the sleeves from the cylinder head and reinstall them with new O-rings.
2) Procedures for removing and installing the air cleaner housing, turbocharger, exhaust balance solenoid valve, and exhaust sensor lines.
3) Detailed illustrations and torque specifications are provided for correctly performing each removal and installation step. Proper cleaning and use of new sealing components is emphasized.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...hhfjksekmm
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...hhfjksekmm
The document provides instructions to disassemble and assemble the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, ring gear, carrier assembly, planetary gears, and seals. It then describes the assembly process, providing specifications for torque and installation of components like bolts, bearings, seals, and shims. Proper cleaning and use of locking compounds or lubricants is emphasized to ensure correct assembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...hhfjksekmm
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing over 20 components including bolts, seals, retainers, discs, and housing assemblies.
3) Assembly is the reverse of disassembly, requiring pressing or installing components like bearings, seals, sleeves and housings back into place and securing with bolts, pins or retaining rings. Cleanliness and use of specified tools and adhesives is important for successful reassembly.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...hhfjksekmm
The document provides instructions for disassembling and assembling the travel motor of a 349E excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order, like installing seals, pins, bearings onto the shaft assembly before pressing it into the motor housing. Tolerances and specifications are provided for components like springs, seals, and fasteners.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 27 steps to remove components from the motor housing, head assembly, rotating group, and barrel assembly. The assembly process describes 13 steps and specifications to reinstall components in the reverse order, ensuring proper torque values and lubrication of parts. Key components include the motor housing, head assembly, shaft assembly, barrel assembly, pistons, bearings, seals, springs, and related hardware.
Caterpillar cat 349 e l excavator (prefix mzw) service repair manual (mzw0000...hhfjksekmm
This document provides assembly instructions for a 349E L excavator final drive group. It includes specifications for the components and a step-by-step procedure for assembling the final drive. Some key steps include applying anti-seize compound to bearings, using shims to adjust clearances, and torquing bolts to the specified values. Tools required include a transmission repair stand, eyebolts, and torque wrenches. The assembly procedure has 30 steps and ensures the final drive is properly assembled and adjusted.
Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz0000...hhfjksekmm
This document provides instructions for removing and installing a water pump on a 349E L excavator. The removal procedure involves: 1) Removing the water temperature regulator and fan drive; 2) Removing various sheet assemblies and supports; 3) Disconnecting support assemblies and repositioning harness assemblies; 4) Removing hoses. The installation procedure involves reversing the removal steps and applying threadlock to bolts.
Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx0000...hhfjksekmm
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
Caterpillar cat 349 e l excavator (prefix fjb) service repair manual (fjb0000...hhfjksekmm
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. It describes 22 steps to disassemble the components, including removing bolts, retainers, seals, discs, and housing parts. It then describes 14 steps for reassembling the components, applying sealant and installing seals, sleeves, bearings and housing pieces in the reverse order of disassembly. Precision cleaning and special tools are required to prevent damage to parts during the process.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...hhfjksekmm
The document provides instructions for removing and installing various engine components on a Caterpillar 349E L excavator, including:
1) Removing and installing electronic unit injector sleeves, which requires using specialized tools to pull the sleeves from the cylinder head and clean the bore before reinstalling with new O-rings.
2) Procedures for removing and installing the air cleaner housing, turbocharger, exhaust balance solenoid valve, and exhaust sensor lines.
3) Detailed illustrations and torque specifications are provided for correctly performing each removal and installation step.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...hhfjksekmm
The document provides instructions to disassemble and assemble the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive by removing components like the coupling, cover, ring gear, carrier assembly, planetary gears, and seals. It then describes the assembly process in reverse, providing specifications for torque and application of sealants or lubricants during reassembly. Precise alignment and orientation of parts is emphasized to ensure proper reassembly.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349F EXCAVATOR HLB
Configuration: 349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349F and 352F Excavators Machine Systems
Media Number -UENR0194-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07203491
Travel Motor - Disassemble
SMCS - 4351-015
Disassemble Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
154-6182 M12x1.75 mm Forcing Bolt 2
6V-8149 M12x1.75 mm Nut 4
5P-8245 M12 Hard Washer 4
D
- M3x0.5 Threaded Rod 1
3K-3068 3 mm Thrust Washer 1
3C-6969 M3x0.5 Nut 2
E
8T-0276 M8x45mm Bolt 2
9M-1974 M8 Hard Washer 2
Start By:
a. Remove travel motor.
NOTICE
1/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06252257
1. Use Tooling (B) and a suitable lifting device to position travel motor (1) in a vertical
position on Tooling (A). The weight of travel motor (1) is approximately 136 kg (300 lb).
Use Tooling (C) to attach travel motor (1) to Tooling (A).
Illustration 2 g06252275
2. Remove plugs (2), plug (3), plug (4), and the O-ring seals.
2/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 3 g06252280
Illustration 4 g06252989
3. Remove plug (6) and the O-ring seal.
4. Remove plug (5), stopper (7), and ball (8).
3/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g06255756
Illustration 6 g06255791
5. Use Tooling (D) and a suitable washer to extract seat (8A).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g06252992
Illustration 8 g06252996
6. Remove plugs (9) and the O-ring seals.
7. Remove plug (10), spool (11), spring (12), and the O-ring seal.
Illustration 9 g06253028
8. Remove plug (13), valve (14) , and the O-ring seals.
5/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g06253047
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove the top two nuts and washers from Tooling (C).
10. Remove bolts (15).
11. Use Tooling (B) and a suitable lifting device to remove motor head assembly (16). The
weight of motor head assembly (16) is approximately 45 kg (100 lb). Remove motor head
assembly (16).
Illustration 11 g06253060
12. Remove bearing (17) and O-ring seal (18).
6/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g06253330
13. Reinstall the washers and nuts from Tooling (C) that were removed in a previous Step.
14. Remove springs (19), O-ring seal (20), port plate (21), O-ring seal (22), plug (23), and the O
-ring seal.
Note: Port plate (21) may still be adhered to the bottom of motor head assembly (16).
Illustration 13 g06253333
15. Remove orifice (24) and orifice (25).
Illustration 14 g06253335
7/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 16. Remove plug (26).
Illustration 15 g06253475
17. Use Tooling (E) and suitable prying devices to remove piston assembly (27).
Illustration 16 g06253502
Illustration 17 g06253508
Typical example.
18. Remove separator plates (28) and friction plates (29). Note the alternating order of separator
plates (28) and friction plates (29) for assembly purposes.
8/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g06253734
19. Remove barrel assembly (30).
Note: Do not allow the components of barrel assembly (30) to come apart while you
remove barrel assembly (30). The components of barrel assembly (30) must be reinstalled
into the original positions.
Illustration 19 g06253741
20. Remove piston assemblies (31) and retainer (32).
Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g06253748
21. Remove guide (33).
Illustration 21 g06253755
22. Remove springs (34).
Illustration 22 g06254252
23. Put location marks on swashplate (35) for assembly purposes. Remove swashplate (35).
10/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engi...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g06254282
24. Remove snap ring (37) and roller (36).
Illustration 24 g06254306
25. Remove keys (38).
Illustration 25 g06254363
26. Remove snap ring (40).
27. Use a soft faced hammer to remove shaft assembly (39).
11/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engi...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g06254423
28. Remove snap ring (41).
29. Use a suitable press to remove bearing (42) from shaft assembly (39).
Illustration 27 g06254449
30. Remove O-ring seal (43) and O-ring seal (44).
Illustration 28 g06254465
12/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engi...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 29 g06254467
31. Remove plug (45) and use compressed air to remove piston (46).
Illustration 30 g06254480
32. Remove lip seal (47).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 19 12:58:19 UTC+0800 2020
13/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engi...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349F EXCAVATOR HLB
Configuration: 349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349F and 352F Excavators Machine Systems
Media Number -UENR0194-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i06563923
Travel Motor - Assemble
SMCS - 4351-016
Specifications
Illustration 1 g03845362
NOTICE
To prevent damage to the motor, the case must be filled with clean
hydraulic oil at least to the fill port before operation.
1/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Table 1
Specification for 390-1088 Travel Motor Gp
Item Qty Part Specification Description
1 1 5P-7684 Plug Torque to 430 ± 40 N·m (317 ± 30 lb ft).
2 1
6K-6307 O-
Ring Seal
Lubricate with 1U-6396 O-Ring Assembly Compound.
- - -
Before assembly, lubricate the sliding surfaces of the cam plate
(3), the hold-down (4), the pistons (5), the barrel (6) and the shaft
(8) lightly with clean hydraulic oil.
7 20
124-1561 Brake
Spring
Length under test force is 19.0 mm (0.75 inch).
Test force is 425 ± 43 N (96 ± 10 lb).
Free length after test is 22.06 mm (0.869 inch).
9 1
6V-3382 Lip
Type Seal
Apply blue Loctite 243 to the outside diameter.
10 1
118-5805
Special Race
Bearing
Install the snap ring of the special race bearing toward the shaft
flange.
11 2
9S-4185 O-
Ring Plug
Torque to 82 ± 8 N·m (60 ± 6 lb ft).
12 6 8T-4187 Bolt Torque to 530 ± 70 N·m (391 ± 52 lb ft).
13 2
9S-4183 O-
Ring Plug
Torque to 190 ± 20 N·m (140 ± 15 lb ft).
Illustration 2 g03845364
Section A-A
Table 2
2/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Item Qty Part Specification Description
14 2
1T-0936 Pipe
Plug
Install in the orifice toward the head surface or below the head
surface.
15 1 124-1554 Spring
Length under test force is 15 mm (0.6 inch).
Test force is 15.0 ± 2.0 N (3.4 ± 0.4 lb).
Free length after test is 16.15 mm (0.636 inch).
D - -
Depth from the head and interface of the port plate is
20.0 ± 0.2 mm (0.79 ± 0.01 inch).
16 1
195-4456 Orifice
Plug
Torque to 7 ± 1 N·m (62 ± 9 lb in).
Illustration 3 g03845365
Section C-C
Table 3
Item Qty Part Specification Description
17 1 230-5483 Spring
Length under test force is 25 mm (1.0 inch).
Test force is 60.0 ± 8.0 N (13.5 ± 1.8 lb).
Free length after test is 35 mm (1.4 inch).
18 1 087-4786 Adapter Torque to 115 ± 10 N·m (85 ± 7 lb ft).
Assembly Procedure
Table 4
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
D 3E-3879 Eyebolt 1
3/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. F 1U-6396 O-Ring Assembly Compound 1
G - Loctite 242 -
H 1P-0510 Driver Gp 1
J 6V-2055 Grease 1
K 128-5049 Guide Stud 2
Illustration 4 g02421056
1. Lubricate actuator piston (41) with the oil that is being used. Install actuator piston (41) into
housing (2). Apply Tooling (F) onto O-ring seal of plug (40). Install plug (40) into motor
housing (2).Tighten plug (42) to a torque of 430 ± 40 N·m (315 ± 30 lb ft).
2. Apply Tooling (G) onto outside diameter of seal (43). Use Tooling (H) to install seal (43).
Install retaining ring (42).
Illustration 5 g02421000
4/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 6 g02420998
3. Install pins (39) and keys (38) into motor housing (2).
Illustration 7 g02421876
Illustration 8 g02421958
4. Use a suitable press to install bearing (36) and bearing (37) onto shaft assembly (25). Bearing
(36) must be installed with Retaining Clip (X) toward the barrel assembly.
5/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 13 g02423621
8. Use Tooling (D) and a suitable lifting device to install the rotating group into motor housing
(2). The weight of the rotating group is approximately 30 kg (65 lb).
Note: Align the notches of swashplate (29) with the keys in the motor housing (2).
Note: Protect shaft seal (43) from damage by covering the splines on shaft assembly (25) with
heat shrink tubing.
Illustration 14 g02423738
8/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 15 g02423742
9. Install plates (26) and friction discs (27). Start with plate (26). Alternate between plates (26)
and friction discs (27) with plates (26) on the top and the bottom.
Illustration 16 g02419659
10. Install backup ring (21) and O-ring seal (22) onto brake piston (20).
11. Install backup ring (24) and O-ring seal (23) onto brake piston (20).
Illustration 17 g02419577
12. Install O-ring seals (19) onto motor housing (2). Install springs (18) onto brake piston (20).
9/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engine(...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 18 g02419439
13. Install balls (17), backup rings (15), O-ring seals (16), and retainers (14) into head assembly
(3).
Illustration 19 g02419416
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install spring (13), spool (12), and adapter (11). Tighten adapter (11) to a torque of
115 ± 10 N·m (85 ± 7 lb ft).
10/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engi...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 20 g02419359
15. Install ball (9), spring (8), and orifice (7). Tighten orifice (7) to a torque of 7 ± 1 N·m
(62 ± 9 lb in).
16. Install bearing (6) and O-ring seal (10) onto head assembly (3).
Illustration 21 g02001974
Illustration 22 g02419358
17. Apply Tooling (K) to the back side of plate (5) to hold plate (5) in place during assembly.
Install plate (5) to head assembly (3).
11/13
349F & 349F L Excavators HLB00001-UP (MACHINE) POWERED BY C13 Engi...
2020/10/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...