This document provides disassembly and assembly instructions for the final drive of a 345D excavator. It details 30 steps to disassemble the final drive components including removing the final drive cover, carrier assemblies, ring gear, and other parts. It then lists 21 steps to reassemble the final drive, applying anti-seize compound to bearings, installing bearing cups and cones, and refitting the various components removed during disassembly. The document includes detailed illustrations and references other service manuals for additional information.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the final drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures for disassembling components such as the final drive cover, carrier assemblies, ring gear, and sprocket housing. It also provides instructions for assembling these components in reverse order, making sure to clean parts and apply lubricants where specified.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive components of a 345D L Excavator. It describes removing 28 components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly is described in 21 steps, beginning with installing bearing cups into the sprocket housing and ending by attaching the coupling to the motor housing. Tools required are listed.
Caterpillar cat 345 d l excavator (prefix eeh) service repair manual (eeh0000...ifkkdkmdmd
This document provides instructions for disassembling and assembling the final drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures for disassembling components such as the final drive cover, carrier assemblies, ring gear, and sprocket housing. It also provides instructions for assembling these components in reverse order, making sure to clean parts and apply lubricants where specified.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the final drive components of a 345D L Excavator. It describes removing 28 components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly is described in 21 steps, beginning with installing bearing cups into the sprocket housing and ending by attaching the coupling to the motor housing. Tools required are listed.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual Instant D...ze3xiandiao
This document provides instructions for disassembling and assembling the final drive components of a 345D L excavator. It lists the required tools and presents step-by-step procedures for removing and installing parts like the final drive cover, carrier assemblies, ring gear, and sprocket housing. Detailed illustrations accompany each step to show how to properly position lifting devices and disassemble/reassemble components.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual (EEH00001...jdkskmmdmd1
This document provides instructions for disassembling and assembling the final drive components of a 345D L Excavator. It describes removing 28 components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly is described in 21 steps, beginning with installing bearing cups into the sprocket housing and ending by attaching the coupling to the motor housing. Tools required are listed.
Caterpillar cat 345 d l excavator (prefix eeh) service repair manual (eeh0000...jjfksekdmejik
This document provides instructions for disassembling and assembling the final drive components of a 345D L Excavator. It describes removing 28 components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. It then describes assembling the final drive in 29 steps, reinstalling the components in reverse order. The document includes diagrams illustrating each step and provides part numbers for required tools.
Caterpillar cat 345 d l excavator (prefix eeh) service repair manual (eeh0000...hhfjksekmm
This document provides instructions for disassembling and assembling the final drive of a 345D L excavator. It lists the required tools and parts and provides step-by-step instructions to disassemble the various components of the final drive, including removing the cover, carrier assemblies, ring gear, and other parts. It then describes the assembly process in reverse, including pressing in bearings, installing seals, and reassembling the carriers and other components.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the final drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures for disassembling components such as the final drive cover, carrier assemblies, ring gear, and sprocket housing. It also provides instructions for assembling these components in reverse order, making sure to clean parts and apply lubricants where specified.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive components of a 345D L Excavator. It describes removing 28 components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly is described in 21 steps, beginning with installing bearing cups into the sprocket housing and ending by attaching the coupling to the motor housing. Tools required are listed.
Caterpillar cat 345 d l excavator (prefix eeh) service repair manual (eeh0000...ifkkdkmdmd
This document provides instructions for disassembling and assembling the final drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures for disassembling components such as the final drive cover, carrier assemblies, ring gear, and sprocket housing. It also provides instructions for assembling these components in reverse order, making sure to clean parts and apply lubricants where specified.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the final drive components of a 345D L Excavator. It describes removing 28 components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly is described in 21 steps, beginning with installing bearing cups into the sprocket housing and ending by attaching the coupling to the motor housing. Tools required are listed.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual Instant D...ze3xiandiao
This document provides instructions for disassembling and assembling the final drive components of a 345D L excavator. It lists the required tools and presents step-by-step procedures for removing and installing parts like the final drive cover, carrier assemblies, ring gear, and sprocket housing. Detailed illustrations accompany each step to show how to properly position lifting devices and disassemble/reassemble components.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual (EEH00001...jdkskmmdmd1
This document provides instructions for disassembling and assembling the final drive components of a 345D L Excavator. It describes removing 28 components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly is described in 21 steps, beginning with installing bearing cups into the sprocket housing and ending by attaching the coupling to the motor housing. Tools required are listed.
Caterpillar cat 345 d l excavator (prefix eeh) service repair manual (eeh0000...jjfksekdmejik
This document provides instructions for disassembling and assembling the final drive components of a 345D L Excavator. It describes removing 28 components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. It then describes assembling the final drive in 29 steps, reinstalling the components in reverse order. The document includes diagrams illustrating each step and provides part numbers for required tools.
Caterpillar cat 345 d l excavator (prefix eeh) service repair manual (eeh0000...hhfjksekmm
This document provides instructions for disassembling and assembling the final drive of a 345D L excavator. It lists the required tools and parts and provides step-by-step instructions to disassemble the various components of the final drive, including removing the cover, carrier assemblies, ring gear, and other parts. It then describes the assembly process in reverse, including pressing in bearings, installing seals, and reassembling the carriers and other components.
Caterpillar cat 345 d l excavator (prefix eeh) service repair manual (eeh0000...fjjskqazxedmmem
This document provides instructions for disassembling and assembling the final drive of a 345D L excavator. It lists the required tools and parts and provides step-by-step instructions to disassemble the various components of the final drive, including removing the cover, carrier assemblies, ring gear, and other parts. It then describes the assembly process in reverse, including pressing in bearings, installing seals, and reassembling the carriers and other components.
This document provides step-by-step instructions for disassembling and assembling the final drive of a 345C excavator. It details removing over 30 individual parts in 28 steps, including the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. Required tools include a transmission stand, link brackets, retaining ring pliers, eyebolts, and seal installer. Precise positioning of identification marks is noted for reassembly.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over a dozen parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure outlines installing bearing cups, cones, shims, seals, and other parts in reverse order of disassembly to reassemble the final drive, ensuring proper bearing preload is achieved. Tools and torque specifications are listed to complete the process.
Caterpillar cat 345 c excavator (prefix taj) service repair manual (taj00001 ...cfvdssd
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over a dozen parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure outlines installing bearing cups, cones, shims, seals, and other parts in reverse order of disassembly to reassemble the final drive, ensuring proper bearing preload is achieved. Tools and torque specifications are listed to complete the process.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are listed to complete the process.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are provided for correctly reassembling the final drive.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are provided for correctly reassembling the final drive.
This document provides step-by-step instructions for disassembling and assembling the final drive of a 345C excavator. It details removing over 30 individual parts in 28 steps, including the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. Required tools include a transmission stand, link brackets, retaining ring pliers, eyebolts, and seal installer. Precise positioning of identification marks is noted for reassembly.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are listed to complete the process.
This document provides step-by-step instructions for disassembling and assembling the final drive of a 345C excavator. It details removing over 30 individual parts in 28 steps, including the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. Required tools include a transmission stand, link brackets, retaining ring pliers, eyebolts, and seal installer. Precise positioning of identification marks is noted for reassembly.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are listed to complete the process.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are listed to complete the process.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are provided for correctly reassembling the final drive.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are listed to complete the process.
Caterpillar cat 345 c excavator (prefix taj) service repair manual (taj00001 ...fjjseksxckmdme
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are provided for correctly reassembling the final drive.
Caterpillar cat 345 c excavator (prefix taj) service repair manual (taj00001 ...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are provided for correctly reassembling the final drive.
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
More Related Content
Similar to Caterpillar Cat 345D Excavator (Prefix NEG) Service Repair Manual (NEG00001 and up).pdf
Caterpillar cat 345 d l excavator (prefix eeh) service repair manual (eeh0000...fjjskqazxedmmem
This document provides instructions for disassembling and assembling the final drive of a 345D L excavator. It lists the required tools and parts and provides step-by-step instructions to disassemble the various components of the final drive, including removing the cover, carrier assemblies, ring gear, and other parts. It then describes the assembly process in reverse, including pressing in bearings, installing seals, and reassembling the carriers and other components.
This document provides step-by-step instructions for disassembling and assembling the final drive of a 345C excavator. It details removing over 30 individual parts in 28 steps, including the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. Required tools include a transmission stand, link brackets, retaining ring pliers, eyebolts, and seal installer. Precise positioning of identification marks is noted for reassembly.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over a dozen parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure outlines installing bearing cups, cones, shims, seals, and other parts in reverse order of disassembly to reassemble the final drive, ensuring proper bearing preload is achieved. Tools and torque specifications are listed to complete the process.
Caterpillar cat 345 c excavator (prefix taj) service repair manual (taj00001 ...cfvdssd
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over a dozen parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure outlines installing bearing cups, cones, shims, seals, and other parts in reverse order of disassembly to reassemble the final drive, ensuring proper bearing preload is achieved. Tools and torque specifications are listed to complete the process.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are listed to complete the process.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are provided for correctly reassembling the final drive.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are provided for correctly reassembling the final drive.
This document provides step-by-step instructions for disassembling and assembling the final drive of a 345C excavator. It details removing over 30 individual parts in 28 steps, including the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. Required tools include a transmission stand, link brackets, retaining ring pliers, eyebolts, and seal installer. Precise positioning of identification marks is noted for reassembly.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are listed to complete the process.
This document provides step-by-step instructions for disassembling and assembling the final drive of a 345C excavator. It details removing over 30 individual parts in 28 steps, including the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. Required tools include a transmission stand, link brackets, retaining ring pliers, eyebolts, and seal installer. Precise positioning of identification marks is noted for reassembly.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are listed to complete the process.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are listed to complete the process.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are provided for correctly reassembling the final drive.
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are listed to complete the process.
Caterpillar cat 345 c excavator (prefix taj) service repair manual (taj00001 ...fjjseksxckmdme
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are provided for correctly reassembling the final drive.
Caterpillar cat 345 c excavator (prefix taj) service repair manual (taj00001 ...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are provided for correctly reassembling the final drive.
Similar to Caterpillar Cat 345D Excavator (Prefix NEG) Service Repair Manual (NEG00001 and up).pdf (16)
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
This document provides instructions for removing and installing engine oil filter bases and related components on Caterpillar 3304B and 3306B engines. The procedures describe removing the oil filter, oil filter base, gaskets and O-rings. Instructions are provided for disassembling the oil filter base by removing covers, bolts, springs and plungers. Reassembly and installation steps are also outlined. Tools required are listed for each procedure. Precautions are noted to keep parts clean and contain fluids.
Caterpillar Cat D250E II Articulated Truck (Prefix 4PS) Service Repair Manual...paws21610697
The document provides instructions for disassembling and assembling the piston pump used for steering on a D250E II Articulated Truck. The disassembly procedure involves removing 21 individual parts from the pump housing. The assembly procedure instructs assembling the 21 parts in the reverse order, applying lubrication and torque specifications as needed. Tools required include various drivers, pliers, and lubricants.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Cleaning and replacement parts are also discussed. Tools required are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 industrial engine, including the oil cooler, oil filter base, oil bypass valves, engine oil cooler/lines, aftercooler, and turbocharger. The procedures describe removing bolts, hoses, seals, and other parts, cleaning components, applying sealant, and reinstalling parts in reverse order.
The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D EXCAVATOR NEG
Configuration: 345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i05331566
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Stand Group 1
B 138-7573 Link Bracket 2
C 1P-1860 Retaining Ring Pliers 1
D 4C-8359 Eyebolt 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive and Travel Motor
- Remove" in this manual.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
1/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01207795
2. Remove coupling (1) from final drive (2) .
3. Attach a suitable lifting device to the final drive, and turn final drive (2) over 180 degrees.
The weight of final drive (2) is approximately 590 kg (1300 lb).
Illustration 2 g01207796
4. Attach the final drive to Tooling (A) . Put an alignment mark across the sections of the final
drive for assembly purposes. All parts must be reinstalled in the original locations.
5. Remove socket head screws (3) from the final drive cover.
2/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01207801
6. Attach Tooling (B) and a suitable lifting device to cover (5) , as shown. The weight of cover
(5) is approximately 52 kg (115 lb).
7. Remove bolts (4) and the washers that hold the cover in place.
8. Use a soft faced hammer in order to break the seal between cover (5) and the ring gear.
Remove cover (5) . The weight of cover (5) is 52 kg (115 lb).
Illustration 4 g01207835
9. Remove spacer (6) from the cover.
3/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01207845
10. Remove shims (7) from the cover.
11. Remove socket head bolts (8) and ring gear (9) from the cover.
Illustration 6 g01207864
12. Remove sun gear (10) from carrier assembly (11) . Remove carrier assembly (11) by lifting
the carrier assembly straight up.
13. Disassemble carrier assembly (11) , as follows:
4/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g01207865
a. Remove spacers (12) . A spacer is located on each side of the sun gear in carrier
assembly (11) .
Note: Planetary gears (15) might be stamped with identification marks "L". Note the
position of the identification marks in relation to the carrier for assembly purposes.
Illustration 8 g01207897
b. Remove retaining ring (13) with Tooling (C) .
c. Remove thrust washers (14) and planetary gear (15) from the carrier.
d. Remove bearing (16) from the planetary gear.
e. Repeat Steps 13.b through 13.d for the other two planetary gears.
Illustration 9 g01208035
f. Use a screwdriver in order to remove retaining ring (17) from the carrier. Remove sun
gear (18) from the carrier.
5/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g01208136
14. Attach Tooling (D) and a suitable lifting device to carrier assembly (19) , as shown.
Remove carrier assembly (19) by pulling the carrier assembly straight up. The weight of
carrier assembly (19) is approximately 45 kg (100 lb).
15. Disassemble carrier assembly (19) , as follows:
Note: Spacer (20) may remain with carrier assembly (19) , or the spacer may remain with
carrier assembly (28) . Refer to Step 17.
Illustration 11 g01208162
a. Remove spacer (20) from carrier assembly (19) .
6/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g01208169
b. Drive spring pin (21) into planetary shaft (22) with a hammer and a punch.
Illustration 13 g01208189
c. Remove planetary shaft (22) , two thrust washers (23) and planetary gear (24) from
the carrier.
Note: Planetary gears (24) might be stamped with identification marks "M". Note the
position of the identification marks in relation to the carrier for assembly purposes.
d. Remove bearing (25) from the planetary gear.
e. Remove spring pin (21) from planetary shaft (22) with a hammer and a punch.
f. Repeat Steps 15.b through 15.e in order to remove the other two planetary gears from
the carrier.
7/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g01208245
g. Use a screwdriver to remove retaining ring (26) . Remove sun gear (27) from the
carrier.
Illustration 15 g01208253
16. If spacer (20) was not removed in Step 15.a, remove the spacer from carrier assembly (28)
at this time.
Illustration 16 g01208256
8/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 17. Attach Tooling (E) and a suitable lifting device to carrier assembly (28) , as shown. Remove
carrier assembly (28) . The weight of carrier assembly (28) is approximately 64 kg (140 lb).
18. Disassemble carrier assembly (28) , as follows:
Illustration 17 g01208265
a. Drive spring pin (29) into planetary shaft (30) with a hammer and a punch.
Illustration 18 g01208280
b. Remove planetary shaft (30) , two thrust washers (31) , and planetary gear (32) from
the carrier.
Note: Planetary gears (32) might be stamped with identification marks "N". Note the
position of the identification marks in relation to the carrier for assembly purposes.
c. Remove bearings (33) from the planetary gear.
d. Drive spring pin (29) out of planetary shaft (30) with a hammer and a punch.
e. Repeat Steps 18.a through 18.d in order to remove the other three planetary gears
from the carrier.
9/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g01208300
19. Fasten Tooling (E) and a suitable lifting device to ring gear (34) , as shown. Remove ring
gear (34) from sprocket housing (35) . The weight of ring gear (34) is approximately 82 kg
(180 lb).
Illustration 20 g01208542
20. Remove O-ring seal (36) from sprocket housing (35) .
10/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP4...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 21 g01208553
Note: Mark the orientation of coupling (38) for assembly purposes.
21. Remove bolts (37) from coupling gear (38) .
Illustration 22 g01208572
22. Install suitable forcing bolts (39) in coupling gear (38) , as shown. Tighten the forcing bolts
evenly in order to loosen coupling gear (38) . Remove the coupling gear from the motor
housing.
Illustration 23 g01208578
11/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP4...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 24 g01208625
23. Remove shims (40) from the motor housing.
Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.
24. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35) , as shown.
Separate the sprocket housing from the motor housing. The weight of sprocket housing (35)
is 127 kg (280 lb).
Illustration 25 g01208626
25. Remove the locating pins from the motor housing.
26. Remove duo-cone seal gp (41) from the motor housing.
27. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
12/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP4...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 26 g01208633
28. Remove duo-cone seal gp (43) from the sprocket housing.
29. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.
30. Remove the bearing cups from the sprocket housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 22 12:16:30 UTC+0800 2020
13/13
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP4...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D EXCAVATOR NEG
Configuration: 345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i05970668
Final Drive - Assemble
SMCS - 4050-016
S/N - BYC1-UP
S/N - DKN1-UP
S/N - EEH1-UP
S/N - GAX1-UP
S/N - GKF1-UP
S/N - JGB1-UP
S/N - KFH1-UP
S/N - KHS1-UP
S/N - KLH1-UP
S/N - LKY1-UP
S/N - MEN1-UP
S/N - MLK1-UP
S/N - NEG1-UP
S/N - NLM1-UP
S/N - NNF1-UP
S/N - P271-UP
1/21
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. S/N - P5D1-UP
S/N - PBT1-UP
S/N - PFD1-UP
S/N - PZG1-UP
S/N - RAE1-UP
S/N - RAJ1-UP
S/N - RAN1-UP
S/N - RBJ1-UP
S/N - RGD1-UP
S/N - RGG1-UP
S/N - SDM1-UP
S/N - TAH1-UP
S/N - WTD1-UP
S/N - XAC1-UP
S/N - YAE1-UP
S/N - YAG1-UP
S/N - YEE1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1860 Retaining Ring Pliers 1
D 4C-8359 Eyebolt 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
2/21
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. G 8T-0531 Duo-Cone Seal Installer As 1
H 4C-5599 Anti-Seize Compound 1
J 9S-3263 Thread Lock Compound 1
K 1U-8846 Gasket Sealant 1
L 6V-7059 Micrometer 1
M 1U-9895 Crossblock 1
1. Make sure that all parts of the final drive are thoroughly clean and free of dirt and debris
prior to assembly. Check the condition of all O-ring seals that are used in the final drive. If
any of the seals are damaged, use new parts for replacement. Reassemble the final drive on
Tooling (A) .
Illustration 1 g01208879
2. Apply Tooling (H) to the surfaces inside sprocket housing (35) that makes contact with the
bearing cups. Install a bearing cup that is in each side of the sprocket housing with a press.
Make sure that the bearing cups are properly seated.
3. Apply Tooling (H) to the surfaces inside the motor housing that makes contact with bearing
cones (42) .
4. Install inner bearing cone (42) on the motor housing.
3/21
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g01208625
5. Apply Tooling (F) and a suitable lifting device to sprocket housing (35) , as shown. The
weight of sprocket housing (35) is approximately 127 kg (280 lb). Install sprocket housing
(35) on the motor housing. Carefully install outer bearing cone (42) on the sprocket housing.
Illustration 3 g01208578
6. Adjust the bearing preload of the final drive. Determine the correct number of shims (40)
that are required for the proper bearing preload, as follows:
Illustration 4 g01208987
4/21
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. a. Use a depth micrometer in order to measure the step height of coupling gear (38) at
several locations around the gear. Find the average for the measured dimensions
around the gear and record the dimension. Call this Dimension (X) .
b. Apply a load of 10000 kg (22000 lb)to bearing cones (42) .
c. Rotate sprocket housing (35) several times in order to seat the bearing cones.
d. Reduce the load to 3500 ± 350 kg (7700 ± 770 lb).
Illustration 5 g00631001
Illustration 6 g03742848
e. While the load is still on the bearing cones, measure the distance between the top face
of the motor housing and the top face of bearing cone (42) . Take measurements in
several locations around the motor housing. Find the average of the measured
dimensions, and record the dimensions. Call this Dimension (Y) .
f. Determine the correct thickness of shims (40) which are used between bearing cone
(42) and coupling gear (38) . Use the following equation in order to determine the
shim pack thickness.
Shim pack thickness ... (X) − (Y) ± 0.05 mm (0.002 inch)
5/21
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Note: If shims (40) are required, install the thinnest shim next to coupling gear (38)
during final assembly.
Illustration 7 g01208625
7. Apply Tooling (F) and a suitable lifting device to sprocket housing (35) , as shown.
Separate sprocket housing (35) from the motor housing.
ReferenceRefer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that makes contact with the seals must be clean and
dry. After installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal
seals.
Illustration 8 g00631006
6/21
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 9 g01208999
8. Install Duo-Cone seal kit (43) in the sprocket housing with Tooling (G) .
Illustration 10 g00631014
Illustration 11 g01208626
7/21
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 12 g01208625
9. Install Duo-Cone seal kit (41) in the motor housing with Tooling (G) .
10. ApplyTooling (H) in the bores for the locating pins that are in the motor housing. Reinstall
the locating pins in the motor housing.
11. Make sure that inner bearing cone (42) is seated properly on the motor housing.
Note: Do not scratch Duo-Cone seal gp (41) or damage the Duo-Cone seal gp in the main
housing, or the motor housing during assembly of the two components. After installation of
the main housing on the motor housing, there will be a small gap between the components.
The gap between the components is caused by the Duo-Cone seal kit. This will be
eliminated during the installation of the coupling gear.
12. Attach Tooling (F) and a suitable lifting device to sprocket housing (35) , as shown.
Carefully install the sprocket housing on the motor housing.
13. Install outer bearing cone (42) on the sprocket housing. Make sure that the outer bearing
cone is properly seated.
Illustration 13 g01208578
14. Install shims (40) that were determined in Steps 6.a through 6.f on the end of the sprocket
housing, as shown. If shims were required, make sure that the thinnest shim is installed on
top.
8/21
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 14 g01208553
15. Put coupling gear (38) in the original position on the motor housing.
16. Apply Tooling (J) on the threads of bolts (37) that hold coupling gear (38) in position.
Tighten bolts (37) evenly and tighten the bolts in diagonally opposite pairs.
Illustration 15 g01208542
17. Install O-ring seal (36) in sprocket housing (35) .
9/21
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP495...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 16 g01208300
18. Thoroughly clean the mating surface of sprocket housing (35) that will make contact with
ring gear (34) .
19. Apply a bead of Tooling (K) on the mating surface of ring gear (34) .
20. Attach Tooling (E) and a suitable lifting device to ring gear (34) . Put ring gear (34) in
position on the sprocket housing. The weight of ring gear (34) is approximately 82 kg (180
lb). Make sure that the alignment mark up on the sprocket housing and the ring gear line
with each other.
Illustration 17 g01208280
10/21
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP4...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 18 g01208265
Illustration 19 g00513451
21. Assemble carrier assembly (28) , as follows:
Note: If planetary gear (32) is stamped with an "N", make sure that the planetary gear
identification grooves are facing in the correct direction, which was noted during the
disassembly of the carrier assembly (28) .
a. Assemble carrier assembly (28) .
b. Put clean SAE 30 oil on bearings (33) .
c. Install bearings (33) in planetary gear (32) .
d. Install a thrust washer (31) on each side of the planetary gear.
e. Install the planetary gear and thrust washers in carrier (28) .
11/21
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP4...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. f. Install planetary shaft (30) in carrier (28) and through planetary gear (32) . Make sure
that the spring pin hole in the planetary shaft is in alignment with the spring pin hole
in the carrier.
g. Install spring pin (29) in the carrier and into the planetary shaft. Install the spring pin
until the spring pin is even with the outside surface of the carrier. Orient the split in
the spring pin horizontally to the carrier. Align the split in the spring pin to the left or
to the right. Refer to Illustration 19.
h. Make a stake mark on each side of the spring pin hole in the carrier. This will prevent
the spring pin from falling out of the spring pin hole. Each stake mark should be
approximately 1.5 to 3.00 mm (.59 to .118 inch) from the spring pin hole.
i. Repeat Steps 21.a through 21.h in order to install the remaining three planetary gears
in carrier (30) .
Illustration 20 g01208256
22. Attach Tooling (E) and a suitable lifting device to carrier assembly (28) . The weight of
carrier assembly (28) is approximately 64 kg (140 lb). Put carrier assembly (28) in position
in the ring gear. It will be necessary to rotate carrier assembly (28) back and forth during
installation in order to engage all the gears properly.
Illustration 21 g01208253
12/21
345D Excavator NEG00001-UP (MACHINE) POWERED BY C13 Engine(SEBP4...
2020/9/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...