This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: M325D L MH EXCAVATOR KAY
Configuration: M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
M325D Material Handler Machine Systems
Media Number -RENR9719-02 Publication Date -01/03/2011 Date Updated -16/03/2011
i02233131
Swing Drive - Assemble
SMCS - 5459-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B 5P-5197 Pliers 1
E 138-7574 Link Bracket 2
F 138-7575 Link Bracket 3
G 5P-3931 Anti-Seize Compound 1
H 1U-8846 Gasket Sealant 1
J 9S-3263 Thread Lock Compound 1
K 1P-0520 Driver Gp 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/10
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01126093
1. Use Tooling (K) to install lip seals (28) and O-ring seal (29) in bearing cage (27) .
Illustration 2 g01126367
Note: Lubricate the seals and the seal surface of the shaft with the lubricant that is being
sealed prior to installation of bearing cage (27) .
2. Install bearing cage (27) on pinion shaft (24) .
2/10
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01126373
3. Raise the temperature of bearing (30). Install bearing (30) on pinion shaft (24) .
4. Install spacer (31) .
Illustration 4 g01126447
5. Raise the temperature of bearing (32). Install bearing (32) on pinion shaft (24) .
Illustration 5 g01126490
6. Use Tooling (B ) to install retaining ring (23) on pinion shaft (24) and against bearing (32) .
3/10
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g01126507
Note: Ensure that bearings (30) and (32) are aligned while pinion shaft (24) is positioned.
7. Apply Tooling (G) to the inside diameter of swing drive housing (25) .
8. Attach Tooling (F) and a suitable lifting device to pinion shaft (24) .
9. Lower the temperature of pinion shaft (24) .
10. Install pinion shaft (24) in swing drive housing (25). The weight of pinion shaft (24) is
approximately 50 kg (110 lb).
11. Remove Tooling (F) and the lifting device from pinion shaft (24). Attach Tooling (E) and a
suitable lifting device to swing drive housing (25). The combined weight of swing drive
housing (25), pinion shaft (24), and bearing cage (27) is approximately 151 kg (333 lb).
12. Lift the swing drive vertically. Use a hammer and a drift to align bearing (30) in the lower
bore of swing drive housing (25). When the bearing is properly aligned in the bore, pinion
shaft (24) will drop into the proper position within swing drive housing (25) .
Illustration 7 g01126601
13. ApplyTooling (H) on the threads of bolts (26) .
14. Install bolts (26) .
4/10
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g01125682
15. Use two people or a suitable lifting device to install ring gear (22). The weight of ring gear
(22) is approximately 46 kg (102 lb).
Illustration 9 g01125627
Illustration 10 g01125625
5/10
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 16. Install bearings (20) in gear (19) .
17. Position thrust washers (21) on each side of gear (19). Install gear (19) in carrier assembly
(14). Install shaft (18) in carrier assembly (14) and through gear (19). Make sure that the pin
hole in shaft (18) is aligned with the pin hole in the carrier.
18. Install pin (17) in carrier assembly (14) and into shaft (18). Install pin (17) until pin (17) is
even with the outside surface of carrier assembly (14). Orient the split in the pin
horizontally to the carrier assembly. Align the split in the pin to the left or to the right.
Illustration 11 g00513451
19. Make a stake mark on each side of the hole for pin (17). This will prevent pin (17) from
falling out of the pin hole. Each stake mark should be approximately 1.5 mm (0.06 inch)
from the outside diameter of the pin hole.
20. Repeat Steps 16 through 19 in order to install the remaining three gears (19) .
6/10
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g01125623
21. Use a suitable lifting device to install carrier assembly (14) in ring gear (22). The weight of
carrier assembly (14) is approximately 39 kg (86 lb).
Illustration 13 g01125545
22. Install retaining ring (16) in carrier assembly (14) .
23. Install spacer (15) .
Illustration 14 g01125491
24. Install retaining ring (13) in gear (12) .
7/10
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g01125481
25. Install gear (12). Install retaining ring (11) .
Illustration 16 g01125464
Illustration 17 g01125347
26. Install bearing (9) in gear (8) .
8/10
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 27. Position thrust washers (10) on each side of gear (8). Install gear (8) and thrust washers (10)
in carrier assembly (4). Install shaft (6) in carrier assembly (4) and through gear (8). Make
sure that the pin hole in shaft (6) is aligned with the pin hole in carrier assembly (4) .
28. Install pin (7) in carrier assembly (4) and into shaft (6). Install pin (7) until pin (7) is even
with the outside surface of carrier assembly (4). Orient the split in pin (7) horizontally to
carrier assembly (4). Align the split in pin (7) to the left or to the right.
Illustration 18 g00513451
29. Make a stake mark on each side of the pin hole in carrier assembly (4). This will prevent
spring (7) from falling out of the pin hole. Each stake mark should be approximately 1.5
mm (0.06 inch) from the outside diameter of the pin hole.
30. Repeat Steps 24 through 29 in order to install the remaining three planetary gears in the
carrier assembly.
31. Install sun gear (5) in carrier assembly (4) .
9/10
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g01125227
32. Use a suitable lifting device or two people to install carrier assembly (4). The weight of
carrier assembly (4) is approximately 23 kg (50 lb).
Illustration 20 g01125185
33. Apply Tooling (H) on the flange surfaces of the ring gear and cover (2) .
34. Use Tooling (A) and a suitable lifting device to position cover (2) on the swing drive.
Illustration 21 g01126965
35. Apply Tooling (J) on the thread of bolts (1). Install bolts (1). Tighten bolts (1) to a torque of
270 ± 40 N·m (200 ± 30 lb ft).
End By: Install the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 17 10:13:05 UTC+0800 2020
10/10
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engi...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: M325D L MH EXCAVATOR KAY
Configuration: M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
M325D Material Handler Machine Systems
Media Number -RENR9719-02 Publication Date -01/03/2011 Date Updated -16/03/2011
i02229749
Swing Drive - Install
SMCS - 5459-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
132-8223 Hydraulic Pump and Motor Gp 1
1U-6221 Hydraulic Torque Wrench Gp 1
132-8143 Wrench Link 1
B 138-7573 Link Bracket 2
D 5P-3931 Anti-Seize Compound 1
E 1U-8846 Gasket Sealant 1
F 9S-3263 Thread Lock Compound 1
1. Apply Tooling (D) on the locating pin in the main frame. Also, apply Tooling (D) in the pin
bore in the main frame.
2. Apply Tooling (E) on the mating surface of the main frame and the swing drive housing.
1/2
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00900976
Illustration 2 g00518158
3. Attach Tooling (B) and a suitable lifting device to swing drive (2). The weight of swing
drive (2) is approximately 310 kg (683 lb). Use Tooling (B) and the suitable lifting device to
position swing drive (2) on the machine.
4. Apply Tooling (F) on the threads of bolts (1). Install bolts (1). Tighten bolts (1) with
Tooling (A) .
5. Fill swing drive (2) with oil. Refer to Operation and Maintenance Manual, "Swing Drive Oil
- Check".
End By: Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 17 10:14:01 UTC+0800 2020
2/2
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: M325D L MH EXCAVATOR KAY
Configuration: M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
M325D Material Handler Machine Systems
Media Number -RENR9719-02 Publication Date -01/03/2011 Date Updated -16/03/2011
i02291905
Upper Frame and Undercarriage Frame - Separate
SMCS - 4150-076; 7051-076
Separation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7641 Tube 2
8S-8048 Saddle 2
8S-7615 Pin 4
8S-7625 Collar 2
4C-6486 Stand 2
8S-7650 Cylinder As 2
4C-5809 Electric Hydraulic Pump Gp 1
B FT-3013 Link Assembly 1
C FT-2765 Support Beam As 1
D 8S-7641 Tube 2
8S-8048 Saddle 2
8S-7615 Pin 4
4C-5809 Electric Hydraulic Pump Gp 1
8S-7625 Collar 2
4C-6486 Stand 2
1/6
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 8S-7650 Cylinder As 2
E
132-8112 Torque Wrench Gp 1
132-8223 Hydraulic Pump and Motor Gp 1
Start By:
A. Remove the stick. Refer to Disassembly and Assembly, "Stick - Remove".
Note: Put identification marks on all hose assemblies and on all tube assemblies for installation
purposes.
1. Park the machine on level ground. Turn the upper frame to a 90 degree angle from the
undercarriage.
2. Remove the front drive shaft and the rear drive shaft. Refer to Disassembly and Assembly,
"Drive Shaft - Remove and Install".
Illustration 1 g01147594
3. Use the hydraulics of the machine to retract cylinders (1). Use a suitable lifting device to
reposition stick cylinder pin (4) in boom (2). The weight of stick cylinder pin (4) is
approximately 54 kg (120 lb). Install plates (3) .
4. Remove the swivel. Refer to Disassembly and Assembly, "Swivel - Remove".
2/6
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g01147596
5. Position Tooling (A) below stick cylinder pin (4) .
6. Remove the left side boom cylinder. Refer to Disassembly and Assembly, "Boom Cylinder -
Remove and Install".
Illustration 3 g01147597
7. Use a suitable lifting device to position Tooling (B). The weight of Tooling (B) is
approximately 227 kg (500 lb). Install pin (5). Reposition pin (7) and install plate (6) .
3/6
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g01147599
8. Use a suitable lifting device to position Tooling (C) onto Tooling (D). The weight of
Tooling (C) is approximately 227 kg (500 lb).
Illustration 5 g01147598
9. Position Tooling (C) and Tooling (D) beneath counterweight (8) in order to support
counterweight (8) during the separation procedure.
4/6
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 6 g01147600
10. Disconnect tube assembly (9) .
Illustration 7 g01147601
Note: Note the orientation of bolts (10) for installation purposes.
11. Use Tooling (E) to remove bolts (10) .
Illustration 8 g01147772
5/6
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 12. Use Tooling (C) and Tooling (D) to raise upper frame (11) in 6.4 mm (0.25 inch)
increments. Raise upper frame (11) enough for pinion gear (12) to clear swing bearing (13) .
13. Use a properly rated machine to pull undercarriage frame (14) from underneath upper frame
(11) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 17 10:14:56 UTC+0800 2020
6/6
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: M325D L MH EXCAVATOR KAY
Configuration: M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
M325D Material Handler Machine Systems
Media Number -RENR9719-02 Publication Date -01/03/2011 Date Updated -16/03/2011
i02292929
Upper Frame and Undercarriage Frame - Connect
SMCS - 4150-077; 7051-077
Connection Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7641 Tube 2
8S-8048 Saddle 2
8S-7615 Pin 4
8S-7625 Collar 2
4C-6486 Stand 2
8S-7650 Cylinder As 2
4C-5809 Electric Hydraulic Pump Gp 1
B FT-3013 Link Assembly 1
C FT-2765 Support Beam As 1
D 8S-7641 Tube 2
8S-8048 Saddle 2
8S-7615 Pin 4
4C-5809 Electric Hydraulic Pump Gp 1
8S-7625 Collar 2
4C-6486 Stand 2
1/6
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 8S-7650 Cylinder As 2
E
132-8112 Torque Wrench Gp 1
132-8223 Hydraulic Pump and Motor Gp 1
F 1U-8846 Gasket Sealant 3
G 5P-3931 Anti-Seize Compound 1
Illustration 1 g01147825
1. Apply Tooling (F) to gear and bearing (16). Apply Tooling (G) to dowel hole (15) .
Illustration 2 g01147772
Note: A locating dowel is used to align the upper frame with the undercarriage frame. Make
sure that the dowel is in position in the undercarriage frame prior to installation. Make sure
that pinion gear (12) is properly aligned with swing bearing (13) prior to installation.
2. Use a properly rated machine to pull undercarriage frame (14) under upper frame (11).
3. Use Tooling (C) and Tooling (D) to lower upper frame (11) onto undercarriage frame (14).
Lower upper frame (11) in 6.4 mm (0.25 inch) increments.
2/6
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 3 g01147601
4. Use Tooling (E) to install bolts (10). Tighten bolts (10) to a torque of 900 ± 100 N·m (664 ±
74 lb ft).
Illustration 4 g01147600
5. Connect tube assembly (9) .
3/6
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 5 g01147599
6. Attach a suitable lifting device to Tooling (C). The weight of Tooling (C) is approximately
227 kg (500 lb).
Illustration 6 g01147597
7. Remove pin (5). Remove plate (6). Reposition pin (7). Remove Tooling (B) .
8. Install the right side boom cylinder. Refer to Disassembly and Assembly, "Boom Cylinder -
Remove and Install".
4/6
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 7 g01147596
9. Remove Tooling (A) from stick cylinder pin (4) .
Illustration 8 g01147594
Note: Cylinders (1) were retracted during the separation procedure.
10. Attach a suitable lifting device to stick cylinder pin (4). The weight of stick cylinder pin (4)
is approximately 54 kg (120 lb). Remove stick cylinder pin (4) from boom (2) .
11. Install the swivel. Refer to Disassembly and Assembly, "Swivel - Install".
End By:
a. Install the front drive shaft and the rear drive shaft. Refer to Disassembly and Assembly,
"Drive Shaft - Remove and Install".
b. Install the stick. Refer to Disassembly and Assembly, "Stick - Install".
Tue Nov 17 10:15:52 UTC+0800 2020
5/6
M325D L Material Handler KAY02000-UP (MACHINE) POWERED BY C7 Engine(...
2020/11/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...