This document provides instructions for removing and installing the cylinder head and spacer plate on Caterpillar 330, 330L, and 330LN excavator models. The removal process involves disconnecting various lines and components before removing bolts and lifting the cylinder head off. Installation requires cleaning surfaces, installing gaskets and seals, bolting the head and plate back into place, and reconnecting lines while maintaining proper torque specifications.
Caterpillar cat 329 e l excavator (prefix rld) service repair manual (rld0000...fikkskmmdm
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 330 c l excavator (prefix cap) service repair manual (cap0000...jfdskekdmme
This document provides instructions for disassembling and assembling the final drive component of a 330C excavator model. It lists over 30 detailed steps for disassembly, removing parts like gears, bearings, seals, and housings. Similarly, it lists over 20 detailed steps for assembly, including applying compounds, installing seals and bearings, and pressing components together using various tools. The goal is to disassemble the entire final drive assembly into individual parts and then reassemble all parts back into the final drive assembly. Cleanliness is emphasized throughout to prevent damage during assembly.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 330 c mh excavator (prefix d3c) service repair manual (d3c000...jfdskekdmme
1) The document provides disassembly and assembly instructions for a 330C excavator travel motor.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
3) It then describes 13 steps for assembling the travel motor, including installing seals, bearings, springs, and securing components with bolts, pins, and retaining rings.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...fkjsekksmem
The document provides instructions for removing and installing components related to the crankshaft on a Caterpillar 329E excavator engine, including:
- Removing and installing the vibration damper and pulley, which involves removing screws and installing guide studs.
- Removing and installing the crankshaft front seal using a removal/installation tool.
- Removing and installing the front cover, which requires identifying bolt positions, cleaning surfaces, and installing a new gasket.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, bolts, and lifting devices to separate individual parts from each other.
4. Cleaning components and keeping alignment marks to ensure proper reassembly. The document lists over 30 individual steps and provides illustrations for each step.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5g) service r...ifse9diodkdk
This document provides instructions for disassembling the final drive of a 329D L Mobile Hydraulic Power Unit. It outlines 30 steps to fully disassemble the final drive, including removing gears, carriers, shafts, seals and other components. Various tools are required to secure, lift and remove parts. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 329 e l excavator (prefix rld) service repair manual (rld0000...fikkskmmdm
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar cat 330 c l excavator (prefix cap) service repair manual (cap0000...jfdskekdmme
This document provides instructions for disassembling and assembling the final drive component of a 330C excavator model. It lists over 30 detailed steps for disassembly, removing parts like gears, bearings, seals, and housings. Similarly, it lists over 20 detailed steps for assembly, including applying compounds, installing seals and bearings, and pressing components together using various tools. The goal is to disassemble the entire final drive assembly into individual parts and then reassemble all parts back into the final drive assembly. Cleanliness is emphasized throughout to prevent damage during assembly.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 330 c mh excavator (prefix d3c) service repair manual (d3c000...jfdskekdmme
1) The document provides disassembly and assembly instructions for a 330C excavator travel motor.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
3) It then describes 13 steps for assembling the travel motor, including installing seals, bearings, springs, and securing components with bolts, pins, and retaining rings.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...fkjsekksmem
The document provides instructions for removing and installing components related to the crankshaft on a Caterpillar 329E excavator engine, including:
- Removing and installing the vibration damper and pulley, which involves removing screws and installing guide studs.
- Removing and installing the crankshaft front seal using a removal/installation tool.
- Removing and installing the front cover, which requires identifying bolt positions, cleaning surfaces, and installing a new gasket.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
This document provides instructions for disassembling the final drive on a Caterpillar 329D2 L excavator. The process involves:
1. Removing the final drive and separating it from the track assembly and travel motor.
2. Lifting the final drive and disassembling it into components like the cover, carrier assembly, ring gears, and main housing.
3. Using tools like pins, bolts, and lifting devices to separate individual parts from each other.
4. Cleaning components and keeping alignment marks to ensure proper reassembly. The document lists over 30 individual steps and provides illustrations for each step.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5g) service r...ifse9diodkdk
This document provides instructions for disassembling the final drive of a 329D L Mobile Hydraulic Power Unit. It outlines 30 steps to fully disassemble the final drive, including removing gears, carriers, shafts, seals and other components. Various tools are required to secure, lift and remove parts. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fjskefkemms
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes:
- Releasing hydraulic pressure before removing components
- Removing covers, clamps, hoses and tubes to access the travel motor
- Using a tool and hoist to remove the travel motor, which weighs 120kg
- Cleaning mating surfaces, checking seals and reinstalling components in reverse order
It then details disassembling and assembling the travel motor, including removing the head assembly, brake piston, cylinder assembly parts and seals. Precautions are given to prevent damage and clean/oil parts during reassembly.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 323 e l excavator (prefix yrp) service repair manual (yrp0000...fjskefkemms
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides instructions for reassembling these components, including installing seals, bearings, and gears, and using shims to set proper bearing preload. Bolts and seals must be tightened to the specified torques.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fjskefkemms
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
Caterpillar cat 311 c excavator (prefix pad) service repair manual (pad00001 ...fjskefkemms
The document provides disassembly instructions for the final drive, travel motor, travel brake valve, and traction control valve of an excavator model 311C. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like gears, plates, pistons, springs, and seals from each assembly. Safety warnings are included to take precautions for released spring forces during disassembly.
Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml000...fjskefkemms
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar cat 325 d mobile hyd power unit (prefix c3n) service repair manua...fikkskmmdm
The document provides instructions for removing and installing an alternator from an engine that is still installed in a machine. The procedure involves:
1. Disconnecting the positive battery terminal to prevent wiring damage.
2. Removing the belt from the alternator pulley.
3. Removing bolts securing the alternator and removing it from the engine.
4. Installing the new alternator using the securing bolts and adjusting the belt tension.
Caterpillar cat 311 d lrr excavator (prefix dwr) service repair manual (dwr00...fjsekdmmeed
This document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and the crankshaft on a Caterpillar C4.2 engine. It outlines the required tools and steps to take the components out and put them back in. Key steps include using a piston ring compressor and socket wrench, cleaning and lubricating parts, aligning marks, and torquing connecting rod nuts. The crankshaft removal involves taking off the oil supply tube, installing a nut, and removing main bearing caps.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 120 h es motor grader (prefix 6nm) service repair manual (6nm...fjsekdmmeed
The document provides instructions for removing and installing final drives on a 120H ES motor grader. It describes using an O.T.C. 1790 Transmission Jack to support the final drive while removing nuts and washers. Upon removal of the final drive, it can be cleaned and inspected as needed before reversing the process to reinstall it with new nuts, washers and thread locking compound.
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjskefkemms
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...diskkdkdmdm
The document provides instructions for removing and installing the cylinder head and spacer plate on 330B and 330B L excavator models. The removal process includes disconnecting various components and removing bolts. For installation, the instructions specify cleaning surfaces, installing gaskets and seals in the proper order, and torquing bolts to the specified values. Installation also involves reconnecting removed components and adjusting valve lash.
Caterpillar cat 330 b l excavator (prefix 8tr) service repair manual (8tr0000...diskkdkdmdm
The document provides instructions for removing and installing the cylinder head and spacer plate on 330B and 330B L excavator models. The removal process includes disconnecting various components and removing bolts. For installation, the instructions specify cleaning surfaces, installing gaskets and seals in the proper order, and torquing bolts to the specified values. Installation also involves reconnecting removed components and adjusting valve lash.
Caterpillar cat 330 b l excavator (prefix 8tr) service repair manual (8tr0000...jdfjskekmdme
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator including:
1. The cylinder head removal procedure involves removing the fuel injection lines, exhaust manifold, rocker shaft and pushrods.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts in a specific tightening sequence.
3. Removing the spacer plate requires taking out seals and removing the plate from the cylinder head. Installing requires new seals and gaskets and ensuring surfaces are clean.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...jdfjskekmdme
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying clean oil to bolts before tightening to specified torques.
Caterpillar cat 330 b l excavator (prefix 8tr) service repair manual (8tr0000...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying engine oil to bolts before tightening to specified torques.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying engine oil to bolts before tightening to specified torques.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...cdfzxs
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying clean oil to bolts before tightening to specified torques.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjskefkemms
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate removal and installation.
2. Camshaft removal and installation.
3. Camshaft bearing removal and installation.
4. Connecting rod bearing removal and installation.
5. Crankshaft main bearing removal and installation.
The instructions describe the individual steps for removing and installing each component, including the use of any necessary tools. Safety notices and additional notes are also provided throughout.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...fjskefkemms
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes:
- Releasing hydraulic pressure before removing components
- Removing covers, clamps, hoses and tubes to access the travel motor
- Using a tool and hoist to remove the travel motor, which weighs 120kg
- Cleaning mating surfaces, checking seals and reinstalling components in reverse order
It then details disassembling and assembling the travel motor, including removing the head assembly, brake piston, cylinder assembly parts and seals. Precautions are given to prevent damage and clean/oil parts during reassembly.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 323 e l excavator (prefix yrp) service repair manual (yrp0000...fjskefkemms
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides instructions for reassembling these components, including installing seals, bearings, and gears, and using shims to set proper bearing preload. Bolts and seals must be tightened to the specified torques.
Caterpillar cat 330 a l excavator (prefix 5 ym) service repair manual (5ym000...fjskefkemms
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1. The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2. The installation procedure specifies using the same special tool to install the bearings at precise depths in the cylinder block and checking the bore size after installation.
3. Reinstalling components like the flywheel housing, balancer shaft, and oil pan completes the process.
Caterpillar cat 311 c excavator (prefix pad) service repair manual (pad00001 ...fjskefkemms
The document provides disassembly instructions for the final drive, travel motor, travel brake valve, and traction control valve of an excavator model 311C. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like gears, plates, pistons, springs, and seals from each assembly. Safety warnings are included to take precautions for released spring forces during disassembly.
Caterpillar cat 330 a l excavator (prefix 9 ml) service repair manual (9ml000...fjskefkemms
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar cat 325 d mobile hyd power unit (prefix c3n) service repair manua...fikkskmmdm
The document provides instructions for removing and installing an alternator from an engine that is still installed in a machine. The procedure involves:
1. Disconnecting the positive battery terminal to prevent wiring damage.
2. Removing the belt from the alternator pulley.
3. Removing bolts securing the alternator and removing it from the engine.
4. Installing the new alternator using the securing bolts and adjusting the belt tension.
Caterpillar cat 311 d lrr excavator (prefix dwr) service repair manual (dwr00...fjsekdmmeed
This document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and the crankshaft on a Caterpillar C4.2 engine. It outlines the required tools and steps to take the components out and put them back in. Key steps include using a piston ring compressor and socket wrench, cleaning and lubricating parts, aligning marks, and torquing connecting rod nuts. The crankshaft removal involves taking off the oil supply tube, installing a nut, and removing main bearing caps.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 120 h es motor grader (prefix 6nm) service repair manual (6nm...fjsekdmmeed
The document provides instructions for removing and installing final drives on a 120H ES motor grader. It describes using an O.T.C. 1790 Transmission Jack to support the final drive while removing nuts and washers. Upon removal of the final drive, it can be cleaned and inspected as needed before reversing the process to reinstall it with new nuts, washers and thread locking compound.
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjskefkemms
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...diskkdkdmdm
The document provides instructions for removing and installing the cylinder head and spacer plate on 330B and 330B L excavator models. The removal process includes disconnecting various components and removing bolts. For installation, the instructions specify cleaning surfaces, installing gaskets and seals in the proper order, and torquing bolts to the specified values. Installation also involves reconnecting removed components and adjusting valve lash.
Caterpillar cat 330 b l excavator (prefix 8tr) service repair manual (8tr0000...diskkdkdmdm
The document provides instructions for removing and installing the cylinder head and spacer plate on 330B and 330B L excavator models. The removal process includes disconnecting various components and removing bolts. For installation, the instructions specify cleaning surfaces, installing gaskets and seals in the proper order, and torquing bolts to the specified values. Installation also involves reconnecting removed components and adjusting valve lash.
Caterpillar cat 330 b l excavator (prefix 8tr) service repair manual (8tr0000...jdfjskekmdme
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator including:
1. The cylinder head removal procedure involves removing the fuel injection lines, exhaust manifold, rocker shaft and pushrods.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts in a specific tightening sequence.
3. Removing the spacer plate requires taking out seals and removing the plate from the cylinder head. Installing requires new seals and gaskets and ensuring surfaces are clean.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...jdfjskekmdme
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying clean oil to bolts before tightening to specified torques.
Caterpillar cat 330 b l excavator (prefix 8tr) service repair manual (8tr0000...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying engine oil to bolts before tightening to specified torques.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...hfjsekekmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying engine oil to bolts before tightening to specified torques.
Caterpillar cat 330 b excavator (prefix 8tr) service repair manual (8tr00001 ...cdfzxs
This document provides instructions for removing and installing various engine components on a Caterpillar 330B excavator, including:
- Removing the cylinder head by detaching various lines and manifolds, then lifting it off with a device.
- Installing a new spacer plate gasket and O-rings before positioning the spacer plate on the cylinder head and block.
- Removing and installing water directors by carefully aligning them in the cylinder head.
- Instructions specify cleaning parts thoroughly and applying clean oil to bolts before tightening to specified torques.
Caterpillar cat 330 b l excavator (prefix 8tr) service repair manual (8tr0000...cdfzxs
The document provides instructions for removing and installing the cylinder head and spacer plate on 330B and 330B L excavator models. The removal process includes disconnecting various components and removing bolts. For installation, the instructions specify cleaning surfaces, installing gaskets and seals in the proper order, and torquing bolts to the specified values. Installation also involves reconnecting removed components and adjusting valve lash.
Similar to Caterpillar cat 330 excavator (prefix 2 el) service repair manual (2el00001 and up) (8)
Caterpillar cat 330 track type excavator (prefix 6 wj) service repair manual ...udjdkkmdmdm
This document provides instructions for removing and installing travel motors on 330 and 330L excavator models. It describes removing the travel motor by draining oil, releasing hydraulic pressure, removing attachment bolts and hoses, and using a hoist. It then describes disassembling and cleaning the travel motor components like the head assembly, valves, cylinders, and seals. The installation and reassembly process is described in reverse order.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...udjdkkmdmdm
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a Caterpillar 330L excavator engine. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and properly dispose of fluids.
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines. The removal procedure involves using a camshaft bearing tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the engine oil pan and balancer shaft. The installation procedure specifies using the camshaft bearing tool to install the bearings at precise depths and checking the bore size after installation. End steps include reinstalling components like the flywheel housing, balancer shaft, and engine oil pan.
Caterpillar cat 330 l forest swing machines (prefix 8 fk) service repair manu...udjdkkmdmdm
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines:
1) The removal procedure includes using a special tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the oil pan and balancer shaft.
2) The installation procedure specifies using the same special tool to install the front, center, and rear balancer shaft bearings at precise depth measurements in the cylinder block.
3) Additional steps include installing the flywheel housing, balancer shaft, and oil pan after checking that the bearing bores are within specification.
Caterpillar cat 330 l excavator (prefix 2 el) service repair manual (2el00001...udjdkkmdmdm
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removing the spacer plate requires removing seals and installing a new gasket when reinstalling.
4. Water directors are removed from the spacer plate and reinstalled at a specified depth in the cylinder head.
5. Lifter group removal involves
This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines. The removal procedure involves using a camshaft bearing tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the engine oil pan and balancer shaft. The installation procedure specifies using the same tool to install the bearings at precise depth measurements and ensuring their holes are aligned before reinstalling removed components.
The document provides instructions for installing a fuel injection pump on a Caterpillar 330 excavator engine:
1. Install alignment tools and spacers to hold the fuel injection pump and rack in position.
2. Install the fuel injection pump, O-ring seal, and bushing, and tighten to the specified torque.
3. Use a measurement tool to check that the rack has the correct travel of 15.70 mm after installation.
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker assembly.
2. Remove bolts securing the cylinder head and lift it off using a lifting device.
3. To install, place a new gasket and bolt the clean cylinder head to the engine block. Reinstall attached components and adjust valve lash.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...udjdkkmdmdm
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 329 el excavator (prefix pty) service repair manual (pty00001...udjdkkmdmdm
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
Caterpillar cat 329 e ln excavator (prefix rld) service repair manual (rld000...udjdkkmdmdm
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...udjdkkmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torque specifications.
Caterpillar cat 329 e l excavator (prefix rld) service repair manual (rld0000...udjdkkmdmdm
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar cat 329 e excavator (prefix pty) service repair manual (pty00001 ...udjdkkmdmdm
The document provides instructions for removing and installing the front cover on a Caterpillar 329E excavator engine. The removal procedure involves taking out the crankshaft pulley, fan if equipped, and front seal before removing bolts to take off the front cover. The installation procedure specifies cleaning surfaces, installing a new gasket on guide studs, placing the front cover on with bolts, and using a front cover alignment tool.
Caterpillar cat 329 e excavator (prefix k2l) service repair manual (k2l00001 ...udjdkkmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5h) service r...udjdkkmdmdm
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 329D L MOBILE HYD POWER UNIT, including:
- Removing and installing inlet and exhaust valve guides from the cylinder head.
- Removing and installing inlet and exhaust valve seat inserts in the cylinder head.
- Removing the engine oil filter base and oil cooler.
- Disassembling the remote or engine mounted engine oil filter base.
The document provides detailed step-by-step instructions, diagrams and safety notices for completing each procedure. Required tools are listed for each job.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix l5g) service r...udjdkkmdmdm
This document provides instructions for disassembling and assembling the final drive of a 329DL Mobile Hydraulic Power Unit. It lists the required tools and presents 36 steps for disassembly, including removing gears, carriers, seals, and housing components. The final drive assembly weighs approximately 550 kg and its individual parts require lifting devices due to their weights ranging from 32 to 254 kg.
Caterpillar cat 329 dl mobile hyd power unit excavator (prefix j8d) service r...udjdkkmdmdm
The document provides instructions for disassembling the final drive of a 329DL Mobile Hydraulic Power Unit. It lists required tools and describes a 37 step process involving removing housing, gears, carriers, shafts, seals, and other components. Special tools are needed to remove some parts, and lifting devices are required due to component weights up to 550 kg. Cleanliness is important to prevent dirt from entering mechanisms during reassembly.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 2EL
Configuration: 330, 330 L AND 330 LN EXCAVATORS 2EL00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00991114
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
B. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
C. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00505124
1. Loosen hose clamp (2) on the hose that connects the oil cooler to water pump elbow (1) .
Illustration 2 g00505164
2. Remove two bolts (3) that fasten water pump elbow (1) to the cylinder head. Remove two
bolts (4) that fasten water pump elbow (1) to the water pump.
3. Carefully remove water pump elbow (1) and the gaskets from the engine.
2/4(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Illustration 3 g00538842
4. Disconnect tube (5) from the inlet manifold.
Illustration 4 g00538845
5. Remove four bolts (6) and remove air inlet pipe (7) .
Illustration 5 g00541454
3/4(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. NOTICE
Do not set the cylinder head on a hard, flat surface. Damage may occur
to the fuel injection nozzle tips.
6. Remove all bolts (8) and (9) that hold the cylinder head to the cylinder block.
Illustration 6 g00505311
7. Attach the proper lifting device in order to remove cylinder head (10) from the engine.
Remove cylinder head (10) from the engine. The weight of cylinder head (10) is
approximately 95 kg (210 lb).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 14 11:47:21 UTC+0800 2020
4/4(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 2EL
Configuration: 330, 330 L AND 330 LN EXCAVATORS 2EL00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07489822
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: When the cylinder head is removed, a new spacer plate gasket must be installed. Refer to
Disassembly and Assembly, "Spacer Plate - Remove and Install".
1. Ensure that the surface of the cylinder head is clean and dry. Install a new dry cylinder head
gasket onto the cylinder block.
Illustration 1 g00541495
1/5(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. 2. Fasten the proper lifting device to cylinder head (1). Put cylinder head (1) in position on the
cylinder block. Remove the lifting device after cylinder head (1) is positioned.
Illustration 2 g00541497
3. Apply clean engine oil to the threads and the washer faces of cylinder head bolts (2) and (3).
Install cylinder head bolts (2) and (3). Tighten the cylinder head bolts finger tight.
Note: Do not tighten the cylinder head bolts at this time.
Illustration 3 g00511493
4. Install pushrods (4). Make sure that the pushrods are installed in the original location and
that the pushrods are seated correctly in the valve lifters.
5. Loosen the adjusting screws on rocker arms (5) for valve clearance. This will prevent a bent
valve or a broken pushrod during installation.
6. Install a new O-ring seal in the rear rocker arm support.
7. Apply clean engine oil to all the rocker shaft bolts except bolt (25). Refer to illustration 5.
8. Put rocker shaft assembly (5) in position on the cylinder head. Make sure that the dowels in
the rocker shaft supports are aligned with the dowel holes in the cylinder head.
9. Ensure that the rocker arms are aligned with the pushrods and install the rocker shaft
mounting bolts. Tighten the rocker shaft mounting bolts finger tight.
2/5(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Illustration 4 g00602759
3304B torque sequence
10. Tighten the cylinder head bolts by hand, as follows:
a. Tighten all the bolts (1 through 18) in the numerical sequence to a torque of
150 ± 15 N·m (115 ± 12 lb ft).
b. Tighten all the bolts (1 through 18) again in the numerical sequence to a torque of
250 ± 17 N·m (185 ± 13 lb ft).
c. Tighten all the bolts (1 through 18) again in the numerical sequence to a final torque
of 250 ± 17 N·m (185 ± 13 lb ft).
d. Tighten all the remaining bolts (A through E) to a torque of 43 ± 7 N·m (32 ± 5 lb ft).
3/5(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 5 g00328807
3306B torque sequence
11. Tighten the cylinder head bolts by hand, as follows:
a. Tighten all the bolts (1 through 26) in the numerical sequence to a torque of
150 ± 15 N·m (115 ± 12 lb ft).
b. Tighten all the bolts (1 through 26) in the numerical sequence to a torque of
250 ± 17 N·m (185 ± 13 lb ft).
c. Tighten all the bolts (1 through 26) again in the numerical sequence to a final torque
of 250 ± 17 N·m (185 ± 13 lb ft).
d. Tighten all the remaining bolts (A through G) to a torque of 43 ± 7 N·m (32 ± 5 lb ft).
12. Adjust the inlet valve lash to 0.38 mm (.015 inch) and the exhaust valve lash to 0.64 mm
(.025 inch). Tighten the locknuts for the adjusting screws to a torque of 29 ± 7 N·m
(22 ± 5 lb ft). Refer to the Testing and Adjusting, "Air Inlet and Exhaust System" topic for
additional information on valve lash adjustments.
Illustration 6 g00511911
13. Put the gasket and air inlet pipe (7) in position on the cylinder head. Install four bolts (6) to
fasten air inlet pipe (7) to the cylinder head.
Illustration 7 g00541522
4/5(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. 14. Connect tube (8) to the inlet manifold.
Illustration 8 g00541524
15. Put the gaskets and water pump elbow (11) in position on the engine. Install two bolts (9)
that fasten water pump elbow (11) to the cylinder head. Install two bolts (10) that fasten
water pump elbow (11) to the water pump.
Illustration 9 g00541527
16. Tighten hose clamp (12).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
b. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
c. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 14 11:48:17 UTC+0800 2020
5/5(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 2EL
Configuration: 330, 330 L AND 330 LN EXCAVATORS 2EL00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01045029
Spacer Plate - Remove and Install
SMCS - 1221-010
Removal Procedure
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00540847
1/4(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. 1. Remove O-ring seal (1), water seals (3) and water directors (4) from spacer plate (2) .
Illustration 2 g00540857
NOTICE
Do not damage the dowels as the spacer plate is removed.
2. Remove spacer plate (2) from the cylinder head.
Illustration 3 g00540895
3. Remove O-ring seal (6) and spacer plate gasket (5) from the cylinder head.
Installation Procedure
2/4(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the mating surfaces between the spacer plate and the cylinder block.
Illustration 4 g00540895
2. Install new spacer plate gasket (5) and new O-ring seal (6) .
Note: If the dowels in the cylinder block have been removed for any reason, the overall
height of the installation is 16.0 ± 5.0 mm (.63 ± .20 inch).
Illustration 5 g00540857
Note: Both surfaces of the spacer plate, spacer plate gasket and the top of the cylinder block
must be clean and dry. Do not use any gasket adhesive or other substances on these
surfaces.
3/4(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. 3. Install spacer plate (2) on the cylinder head.
Illustration 6 g00540847
4. Install a new O-ring seal (1). Install new water seals (3). Install new water directors (4) .
5. Check the cylinder liner projection. Refer to Disassembly and Assembly, "Cylinder Liner -
Install".
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 14 11:49:13 UTC+0800 2020
4/4(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 2EL
Configuration: 330, 330 L AND 330 LN EXCAVATORS 2EL00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00943364
Water Directors - Remove and Install
SMCS - 1115-010
Removal Procedure
Start By:
A. Remove the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00481082
1/2(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. 1. Remove water directors (1) from the cylinder head.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the cylinder head before assembly.
Illustration 2 g00481082
2. Install new water director (1) into the cylinder head. Align the notch in water director (1)
with the "V" mark on the cylinder head.
3. Install water director (1) to a depth of 0.8 ± 0.6 mm (0.031 ± 0.023 inch) below the surface
of the cylinder head.
End By: Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 14 11:50:09 UTC+0800 2020
2/2(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 2EL
Configuration: 330, 330 L AND 330 LN EXCAVATORS 2EL00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01042782
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Start By:
A. Remove the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Illustration 1 g00538891
1. Use Tool (A) to remove valve lifter (1), as shown. Put identification marks on the valve
lifters for installation purposes.
2. Repeat Step 1 for the remainder of the valve lifters.
3. Check the diameter of the valve lifters. The diameter of a new valve lifter must be 33.285 ±
0.015 mm (1.3105 ± 0.0005 inch). The diameter of the bore in the cylinder block for a new
valve lifter must be 33.388 ± 0.050 mm (1.3145 ± 0.0020 inch). The maximum permissible
clearance between the valve lifter and the valve lifter bore in the cylinder block must be
0.30 mm (0.012 inch).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Illustration 2 g00538891
2/3(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. 1. Put 8T-2998 Lubricant on valve lifter (1) prior to installation. Install valve lifter (1) with
Tool (A) in the original location in the cylinder block.
2. Repeat Step 1 for the remainder of the valve lifters.
End By: Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 14 11:51:04 UTC+0800 2020
3/3(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 2EL
Configuration: 330, 330 L AND 330 LN EXCAVATORS 2EL00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01037991
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
A. Remove the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
B. Remove the timing gear cover. Refer to Disassembly and Assembly, "Front Housing -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Illustration 1 g00476744
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. The "C" mark on
the crankshaft gear will be aligned with the "C" mark on the camshaft gear.
Illustration 2 g00476743
Note: Put a mark on the teeth of the fuel injection pump drive gear and the idler gear at
location (A). This will help to keep the engine timing correct during the removal and the
installation of the camshaft. Put a mark on the teeth of the idler gear and camshaft gear (2)
at location (B). When the camshaft is installed, the engine timing will be correct when the
mark at location (A) is aligned with the mark at location (B) and the "C" mark on the
crankshaft gear is aligned with the "C" mark on the camshaft gear.
2. Remove the bolts, the lock and washer (1) .
Illustration 3 g00535590
2/5(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. NOTICE
Do not damage the lobes or the bearings when the camshaft is
removed.
3. Carefully remove camshaft (3) from the engine.
4. If necessary, remove the bolts that hold camshaft drive gear (2) to the camshaft and remove
the gear.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00535590
1. Put camshaft drive gear (2) in position on the end of camshaft (3). Install the bolts that hold
camshaft drive gear (2) to camshaft (3). Tighten the bolts to a torque of 55 ± 7 N·m (41 ± 5
lb ft).
NOTICE
Do not damage the lobes or the bearings when the camshaft is installed.
3/5(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. 2. Put 8T-2998 Camshaft Lubricant on the camshaft lobes only and put clean engine oil on the
bearing journals.
Note: During the installation of camshaft (3), rotate the camshaft in both directions in order
to prevent binding in the camshaft bearing bores.
3. Carefully install camshaft (3) into the engine.
Illustration 5 g00476743
Illustration 6 g00476744
4. Make sure that the mark on the teeth of the fuel injection pump drive gear and the idler gear
are in alignment at location (A). Make sure that the mark on the teeth of the idler gear and
camshaft gear (2) are in alignment at location (B). Align the "C" marks on the crankshaft
gear and camshaft gear (2). When all of the timing marks are in alignment the engine timing
is correct.
4/5(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 5. Install washer (1), the lock and the two bolts that hold the camshaft in position in the
engine.
End By:
a. Install the valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
b. Install the timing gear cover. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 14 11:52:00 UTC+0800 2020
5/5(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 2EL
Configuration: 330, 330 L AND 330 LN EXCAVATORS 2EL00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i02473351
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
A. Remove the Flywheel Housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
B. Remove the Oil Pan Plate. Refer to Disassembly and Assembly, "Oil Pan Plate - Remove
and Install".
C. Remove the Camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
27. Illustration 1 g00478567
1. Use Tool (A) to remove the camshaft bearing from the cylinder block. Start with the front
bearings and work to the rear bearing.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4(W)
w
2020/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...