This document provides instructions for removing the engine oil filter base and oil cooler from a Caterpillar 329D LN excavator. The key steps are:
1. Drain engine oil and coolant from the systems before removal to contain fluids.
2. For a remote-mounted filter base, use a strap wrench to remove the oil filter, then remove bolts and the filter base.
3. For an engine-mounted base, drain the cooling system, then remove hoses and bolts to separate the oil cooler from the engine.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02228289
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01127720
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (5), valve spring (4) and valve (2).
1. Use Tooling (A) to compress valve spring (4). Remove retainer locks (6).
2. Remove Tooling (A). Remove spring retainer (5), valve spring (4), and washer (3).
3. Remove valve seal (1) and valve (2).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
2/4
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01127720
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Lubricate valve (2) with clean engine oil. Install valve (2) in the cylinder head assembly.
Install new valve seal (1) against the valve guide.
2. Place the following items on the valve stem: washer (3), valve spring (4) and spring retainer
(5).
Note: A small amount of grease can be used to hold the retainer locks in position during
installation.
3. Use Tooling (A) to compress valve spring (4). Install retainer locks (6).
End By:
3/4
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:20:05 UTC+0800 2020
4/4
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i06201017
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver 1
B 9U-6895 Valve Guide Driver 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01124395
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (B) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver 1
B 9U-6895 Valve Guide Driver 1
C 1U-7792 Guide Collar 1
D 149-4008 Guide Collar 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 2 g01124397
Note: Position the valve guides and tap on the top of the valve guides in order to start the
valve guides into the cylinder head assembly.
1. Use Tooling (A) and Tooling (C) to install inlet valve guides (1) . Install inlet valve guides
(1) until the protrusion is 23.0 ± 0.50 mm (0.90 ± 0.020 inch) above the cylinder head
assembly.
2. Use Tooling (B) and Tooling (D) to install the exhaust valve guides. Install the exhaust
valve guides until the protrusion is 24.05 ± 0.5 mm (1.0 ± 0.02 inch) above the cylinder
head assembly.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:21:01 UTC+0800 2020
3/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02954230
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor(2)
1
165-5647 Valve Seat Extractor(3)
1
6V-4804 Handle 1
6V-4192 Shaft 1
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool Group
(2)
Use for removal of the exhaust valve seats
(3)
Use for removal of the inlet valve seats
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g01124436
1. Use Tooling (A) to remove valve seat inserts (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
149-6115 Installer 1
133-9306 Valve Guide 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g01475612
1. Lower the temperature of new valve seat inserts (1).
2. Use Tooling (B) and a suitable press to install the new valve seat inserts in the cylinder
head.
Note: Do not machine the prefinished valve seat inserts in order to correct the valve stem
projection. An excessive valve stem projection indicates that the valve seat insert is not
seated or material was not cleaned from the bottom of the counterbore.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:21:56 UTC+0800 2020
3/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301129
Engine Oil Filter Base and Oil Cooler - Remove
SMCS - 1306-011; 1378-012
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Remote Mounted Engine Oil Filter Base
1/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Illustration 1 g01152338
1. Use Tooling (A) to remove engine oil filter (1) .
2. Remove bolts (2) and engine oil filter base (3) .
Engine Mounted Engine Oil Filter Base
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
2/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01152340
2. Disconnect hose assemblies (4) .
3. Disconnect hose assembly (5) .
4. Remove bolts (6) and engine oil filter base (7) .
5. Remove oil cooler (8) and the gasket from the engine.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:22:52 UTC+0800 2020
3/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301168
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
A. Remove the engine oil filter base and the oil cooler. Refer to Disassembly and Assembly,
"Engine Oil Filter Base and Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Remote Mounted Engine Oil Filter Base
1/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g01152353
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove oil filter bypass valve (2) from engine oil filter base (1) .
Engine Mounted Engine Oil Filter Base
2/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 2 g01152356
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove adapter (3) and the O-ring seals from engine oil filter base (4) .
2. Remove oil filter bypass valve (5) and oil filter bypass valve (6) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:23:48 UTC+0800 2020
3/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301184
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engine Mounted Engine Oil Filter Base
Table 1
Required Tools
Tool Part Number Part Description Qty
A 155-0695 Thread Lock Compound 1
1/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01152356
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install oil filter bypass valve (6) and oil filter bypass valve (5) in engine oil filter base (4) .
2. Apply Tooling (A) to the threads of adapter (3). Install the O-ring seals and adapter (3).
Tighten adapter (3) to a torque of 150 ± 20 N·m (110 ± 15 lb ft).
Remote Mounted Engine Oil Filter Base
2/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g01152353
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install oil filter bypass valve (2) in engine oil filter base (1) .
End By: Install the engine oil filter base and the oil cooler. Refer to Disassembly and Assembly,
"Engine Oil Filter Base and Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:24:44 UTC+0800 2020
3/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301151
Engine Oil Filter Base and Oil Cooler - Install
SMCS - 1306-012; 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engine Mounted Engine Oil Filter Base
1/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g01152340
1. Position the gasket and oil cooler (8) on the engine.
2. Install engine oil filter base (7) and bolts (6) .
3. Connect hose assembly (5) .
4. Connect hose assemblies (4) .
5. Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System
Coolant - Change".
Remote Mounted Engine Oil Filter Base
2/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 2 g01152338
1. Position engine oil filter base (3) and install bolts (2) .
2. Install engine oil filter (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:25:39 UTC+0800 2020
3/3
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D LN EXCAVATOR SCY
Configuration: 329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
C7
Engines for Caterpillar Built Machines
Media Number -RENR9218-13 Publication Date -01/06/2014 Date Updated -04/06/2014
i02301238
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g01152440
1. Remove bracket (5) .
2. Remove pickup tube (4) and the gasket from engine oil pump (1) .
3. Remove outlet elbow (3) and the O-ring seals from engine oil pump (1) .
4. Remove bolts (2) and engine oil pump (1) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Apr 23 13:26:35 UTC+0800 2020
2/2
329D L & 329D LN Excavator SCY00001-UP (MACHINE) POWERED BY C7 Engi...
2020/4/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...