The document provides instructions for removing and installing an alternator from an engine that is still installed in a machine. The procedure involves:
1. Disconnecting the positive battery terminal to prevent wiring damage.
2. Removing the belt from the alternator pulley.
3. Removing bolts securing the alternator and removing it from the engine.
4. Installing the new alternator using the securing bolts and adjusting the belt tension.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 325D MOBILE HYD POWER UNIT C3N
Configuration: 325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
320 VH and VM Variable Gauge Undercarriage
Media Number -KENR8183-01 Publication Date -01/05/2012 Date Updated -24/05/2012
i04893712
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P - 2420 Repair Stand 1
B 1U - 6400 Puller 1
C
5P - 8707 Plate 1
1P - 0520 Driver Group 1
5F - 7366 Forcing Bolt 1
8T - 0207 Bolt 2
3H - 0465 Puller Plate 2
1P - 5546 Cross Block 1
Start By:
a. Remove the final drive.
1/8
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g03034523
1. Secure final drive (3) to Tooling (A) The weight of the final drive is approximately 254 kg
(560 lb). Remove bolts (2) and housing (1). Remove O-ring seal from housing (1).
Illustration 2 g03034527
Illustration 3 g03034528
2. Remove retaining ring (4) and planet gear (5). If necessary, use Tooling (B) to remove
planet gears (5).
2/8
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g03034530
3. Remove retaining ring (7) and planet gear carrier (6).
Illustration 5 g03034536
4. Remove sun gear (8).
Illustration 6 g03034556
5. Remove spacer (9) from sun gear (8).
3/8
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g03034559
Illustration 8 g03034582
6. Remove sun gear (12) and remove retaining ring (10) and planet gears (11). If necessary,
use Tooling (B) to remove planet gears (11).
Illustration 9 g03034575
7. Remove retaining ring (13) and planet carrier (14).
4/8
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 10 g03034581
8. Remove sun gear (16) and remove bolt's (15).
Illustration 11 g03034598
9. Attach suitable lifting device to planet carrier (17). The weight of plant carrier is
approximately 32 kg (70 lb). Remove planet carrier (17).
Illustration 12 g03034599
10. Remove final drive (3) from Tooling (A). Place final drive (3) on floor. The weight of final
drive is approximately 163 kg (360 lb).Remove bolts (18) and flange (19).
5/8
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 13 g03034600
11. Use Tooling (C) to press down on the pushing disc (20), to remove retaining ring (21).
Illustration 14 g03034604
12. Remove springs (22) and brake shaft (23).
Illustration 15 g03034620
13. Remove piston (24).
6/8
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 16 g03034621
14. Remove plates (25) and discs (26) .
Note: Note the order at which the friction discs and plates are removed. For installation
purposes.
Illustration 17 g03034698
15. Remove O-ring seals (27), cap screws (28) and cover (29).
Illustration 18 g03034716
7/8
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 19 g03034718
16. Remove Duo-Cone seal (30) and Duo-Cone seal (31).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 19:32:45 UTC+0800 2020
8/8
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 325D MOBILE HYD POWER UNIT C3N
Configuration: 325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
320 VH and VM Variable Gauge Undercarriage
Media Number -KENR8183-01 Publication Date -01/05/2012 Date Updated -24/05/2012
i06146851
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P - 2420 Repair Stand 1
B 1U - 6400 Puller 1
C
5P - 8707 Plate 1
1P - 0520 Driver Group 1
5F - 7366 Forcing Bolt 1
8T - 0207 Bolt 2
3H - 0465 Puller Plate 2
1P - 5546 Cross Block 1
D
161 - 4350 Duo-Cone Seal Installer 1
165 - 5192 Cord Stock 1
E 1U-5933 Installer 1
1/7
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g03034756
Illustration 2 g03034757
1. Use Tooling (E) and Tooling (D) to assemble Duo-Cone seal (28) . Use Tooling (E) to
install Duo-Cone seal (29) .
Illustration 3 g03034776
2. Install O-ring seals (27) and cover (29) Install cap screws (28) .Tighten cap screws (28) to a
torque of50 N·m (36 lb ft).
2/7
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 4 g03034777
3. Install plates (25) and discs (26) .
Illustration 5 g03034779
4. Install piston (24) .
3/7
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 6 g03034781
5. Install springs (22) and brake shaft (23) .
Illustration 7 g03034796
6. Use Tooling (C) to apply pressure on the pushing disc (20) . Install the retaining ring (21) .
Illustration 8 g03034817
4/7
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 9 g03034820
7. Install flange (19) and bolts (18) , on final drive (3) . Install final drive (3) on to Tooling
(A) . The weight of final drive (3) is 163 kg (360 lb).
Illustration 10 g03034823
8. Install planet carrier (13) and retaining ring (12) .
Illustration 11 g03034828
9. Install planet gears (11) , install retaining ring (10) and, sun gear (12) .
5/7
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 12 g03034831
10. Install spacer (9) onto the sun gear (8) .
Illustration 13 g03034833
11. Install sun gear (8) .
Illustration 14 g03034836
12. Install planet gear carrier (6) and retaining ring (7) .
6/7
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 15 g03034839
13. Install planet gears (5) and retaining ring (4) .
Illustration 16 g03034842
14. Install housing (1) with O-ring seal, install bolts (2) Remove final drive (3) from Tooling
(A) . The weight of the final is approximately 254 kg (560 lb).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 19:33:41 UTC+0800 2020
7/7
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 325D MOBILE HYD POWER UNIT C3N
Configuration: 325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
325D MHPU
Mobile Hydraulic Power Units
Engine Supplement
Media Number -KENR6074-01 Publication Date -01/03/2007 Date Updated -12/03/2007
i07257625
Hydraulic System Pressure - Release
SMCS - 5050-553-PX
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before performing any service. Remove the oil filler cap
only when the engine is stopped, and the filler cap is cool enough to
touch with your bare hand.
The release of hydraulic pressure in a hydraulic circuit is required before service is performed to
that hydraulic circuit. Release the pressure in the hydraulic circuits before any hydraulic lines are
disconnected or removed from that hydraulic circuit.
Reference: Refer to the Operation and Maintenance Manual, "System Pressure Release" for the
detailed procedure to release the system pressure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 19:35:03 UTC+0800 2020
1/1
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 325D MOBILE HYD POWER UNIT C3N
Configuration: 325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
325D MHPU
Mobile Hydraulic Power Units
Engine Supplement
Media Number -KENR6074-01 Publication Date -01/03/2007 Date Updated -12/03/2007
i02540854
Alternator - Remove and Install - Engine in Machine
SMCS - 1405-010
Removal Procedure
Note: Put identification marks on all wires for installation purposes.
1. Disconnect the positive battery terminal. This will prevent any damage to the wiring or the
alternator.
1/6
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01003392
The above Illustration is a reference for the following steps.
Illustration 2 g01272234
2. Remove bolt (7) .
3. Remove nut (6) from lower bolt (1) on alternator (3). Do not remove bolt (1) at this time.
4. Remove guard (5) .
2/6
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 5. Remove spacer (4) and bolt (2) .
Illustration 3 g01003460
6. Remove belt (8) from the alternator. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
Illustration 4 g01003492
7. Disconnect harness assembly (9) .
3/6
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 5 g01217939
8. Remove lower bolt (1) and alternator (3) .
Installation Procedure
Illustration 6 g01217939
1. Position alternator (3) and install lower bolt (1) .
4/6
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 7 g01003492
2. Connect harness assembly (9) to the original locations that were noted during the removal
procedure.
Illustration 8 g01003460
3. Install belt (8) on the alternator. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
5/6
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 9 g01003392
The above Illustration is a reference for the following steps.
Illustration 10 g01272234
4. Install bolt (2) and spacer (4).
5. Position guard (5) .
6. Install bolts (7) .
7. Install nut (6) on lower bolt (1) on alternator (3).
8. Connect the positive battery terminal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 18 19:35:59 UTC+0800 2020
6/6
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 325D MOBILE HYD POWER UNIT C3N
Configuration: 325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
325D MHPU
Mobile Hydraulic Power Units
Engine Supplement
Media Number -KENR6074-01 Publication Date -01/03/2007 Date Updated -12/03/2007
i02540864
Electric Starting Motor - Remove and Install - Engine in
Machine
SMCS - 1453-010
Removal Procedure
1. Move the battery disconnect switch to the OFF position.
2. Disconnect the battery cable on the positive terminal of the battery. Move the battery cable
away from the terminal.
3. Put identification marks on all harness assemblies and on all wires for installation purposes.
Illustration 1 g00787887
4. Remove nut (1). Remove ground strap (2) from the electric starting motor.
1/4
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g01272240
5. Raise the rubber boot and remove nut (3). Remove cable assemblies (4) from the electric
starting motor.
Illustration 3 g01272243
6. Remove the small nut and cover (5). Remove harness assemblies (6) .
7. Remove bolt (7). Move bracket (8) to the side.
2/4
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 4 g00886798
Typical example
8. Fasten a suitable lifting device to electric starting motor (10). The weight of electric starting
motor (10) is approximately 29 kg (65 lb).
9. Remove bolts (9). Remove electric starting motor (10) from the flywheel housing.
Installation Procedure
Illustration 5 g00886798
1. Fasten a suitable lifting device to electric starting motor (10). The weight of the electric
starting motor is approximately 29 kg (65 lb).
2. Place electric starting motor (10) in the flywheel housing. Install bolts (9) .
Illustration 6 g01272243
3. Install bracket (8) in position. Secure bracket (8) with bolt (7) .
3/4
325D L Mobile Hydraulic Power Units C3N00001-UP (MACHINE) POWERED BY ...
2020/6/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...