This document provides instructions for removing and installing engine balancer shaft bearings on 3304B and 3306B engines for Caterpillar built machines. The removal procedure involves using a camshaft bearing tool to pull the six balancer shaft bearings out toward the flywheel end of the engine after removing components like the engine oil pan and balancer shaft. The installation procedure specifies using the same tool to install the bearings at precise depth measurements and ensuring their holes are aligned before reinstalling removed components.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
The Future of Autonomous Vehicles | civilthings.com | Detailed informationgettygaming1
civilthings.com Present Autonomous vehicles, also known as self-driving cars, represent a groundbreaking advancement in transportation technology. These vehicles utilize sophisticated sensors, advanced software, and machine learning algorithms to navigate roads and transport passengers without human intervention. Major companies in the autonomous vehicle industry are investing heavily in the development and testing of these innovative machines, aiming to enhance safety, efficiency, and convenience on the roads.
The autonomous vehicle market is rapidly expanding, driven by technological progress and increasing consumer interest. With the advent of autonomous vehicle technology, the future of transportation promises significant changes, including reduced traffic accidents and lower emissions. However, the widespread adoption of autonomous vehicles faces challenges, such as regulatory hurdles, safety concerns, and public acceptance.
Autonomous vehicle regulations and legislation are evolving to address these issues, ensuring that the integration of self-driving cars into everyday life is smooth and secure. As the industry grows, news and trends related to autonomous vehicles continue to capture global attention. From the development of cutting-edge sensors to advancements in autonomous vehicle software, this sector is poised to revolutionize how we think about mobility.
Stay informed about the latest in autonomous vehicle technology, industry developments, and market trends to understand the profound impact these vehicles will have on our future.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 8FK
Configuration: 330 L, 330 LL & 330 FB FOREST SWING MACHINES 8FK00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01111802
Engine Balancer Shaft - Remove and Install
SMCS - 1220-010-JF
Removal Procedure
Start By:
A. Remove the front housing cover. Refer to Disassembly and Assembly, "Front Housing
Cover - Remove".
B. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/3(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Dispose of all fluids according to local regulations and mandates.
Note: The oil pan plate has been removed for photo purposes only.
Illustration 1 g00590442
1. Remove plates (2) that hold the balancer shaft in the cylinder block.
2. Remove balancer shafts (1) from the cylinder block.
Installation Procedure
Illustration 2 g00590449
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. 1. Install the balancer shafts in each side of the cylinder block.
2. Install plates (2) and the bolts that hold the balancer shafts in position in the cylinder block.
Note: Ensure that the balancer shafts are in time before the oil pump is installed.
End By:
a. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
b. Install the front housing cover. Refer to Disassembly and Assembly, "Front Housing Cover
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 17 00:05:33 UTC+0800 2020
3/3(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 8FK
Configuration: 330 L, 330 LL & 330 FB FOREST SWING MACHINES 8FK00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01135419
Engine Balancer Shaft Bearings - Remove and Install
SMCS - 1220-010-BD
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove".
B. Remove the balancer shaft. Refer toDisassembly and Assembly, "Balancer Shaft -
Remove".
C. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing
Remove" .
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/4(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00602186
Use Tool (A) to remove the six balancer shaft bearing. Pull the balancer shaft bearings toward the
flywheel end of the engine.
Installation Procedure
Illustration 2 g00602186
2/4(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Illustration 3 g00602205
(A) The front bearing depth is 0.8 ± 0.5 mm (0.03 ± 0.02 inch).
(B) The center bearing depth is 290.6 ± 0.5 mm (11.44 ± 0.02 inch).
(C) The rear bearing depth is 601.0 ± 0.5 mm (23.66 ± 0.02 inch).
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
3/4(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. 1. Install the balancer shaft front bearing with Tool (A). Ensure that the holes in the bearings
are aligned with the holes in the cylinder block. The bearing must be 0.8 ± 0.5 mm (0.03 ±
0.02 inch) inside the front face of the cylinder block after installation.
2. Install the balancer shaft center bearing with Tool (A). Ensure that the holes in the bearings
are aligned with the holes in the cylinder block. The bearing must be 290.6 ± 0.5 mm (11.44
± 0.02 inch) inside the front face of the cylinder block after installation.
3. Install the balancer shaft rear bearing with Tool (A). Ensure that the holes in the bearings
are aligned with the holes in the cylinder block. The bearing must be 601.0 ± 0.5 mm (23.66
± 0.02 inch) inside the front face of the cylinder block after installation.
4. Check the bore of the bearings. The balancer shaft bearing bore must be 53.05 ± 0.06 mm
(2.089 ± 0.002 inch) after installation.
End By:
a. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Install" .
b. Install the balancer shaft. Refer to Disassembly and Assembly, "Balancer Shaft - Remove
and Install".
c. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 17 00:06:29 UTC+0800 2020
4/4(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 8FK
Configuration: 330 L, 330 LL & 330 FB FOREST SWING MACHINES 8FK00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00912474
Cylinder Liner - Remove
SMCS - 1216-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8T-0812 Cylinder Liner Puller 1
1U-6317 Bridge 1
1U-6319 Socket 1
Start By:
A. Remove the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
B. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Illustration 1 g00474523
1. Turn the crankshaft until two of the pistons are at the bottom center. Remove two
connecting rod cap bolts (2) from each rod. Remove connecting rod caps (4) .
2. Tap connecting rod (3) away from the crankshaft with a soft hammer. Remove bearing half
(1) .
Illustration 2 g00474623
3. Use tool (A) to remove cylinder liners (5) .
4. Remove the pistons and connecting rods from the cylinder liners.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 17 00:07:24 UTC+0800 2020
2/2(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 8FK
Configuration: 330 L, 330 LL & 330 FB FOREST SWING MACHINES 8FK00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01048841
Cylinder Liner - Install
SMCS - 1216-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-0455 Liner Projection Tool 1
B 2P-8260 Cylinder Liner Installation Tool 1
Note: The following procedure alleviates the need for the crossbar to hold the cylinder liners
during cylinder liner projection measurements.
1. Clean the cylinder liner flange and the cylinder block surface. Remove any nicks on the top
of the cylinder block.
2. Install clean cylinder liners without the rubber seals or the filler band. Install a new spacer
plate gasket and the clean spacer plate.
Table 2
Required Components
Item Part
Number
Part
Description
Quantity For One
Cylinder
Quantity For Six
Cylinders
1 0S-1589 Bolt 6 36
2 2S-0736 Washer 6 36
3 8F-1484 Washer 6 36
4 7K-1977 Washer 6 36
1/5(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Illustration 1 g00544054
3. Install the bolts and washers in the order that is shown in Illustration 1 in order to seat the
cylinder liner in the block. Tighten bolts (1) evenly to a torque of 95 N·m (70 lb ft).
Illustration 2 g00544478
(5) Bolt
(6) Dial Indicator
(7) Gauge Body
(8) Gauge
2/5(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. 4. Loosen bolt (5) until dial indicator (6) can be moved. Place gauge body (7) and dial
indicator (6) on the long side of gauge (8) .
5. Slide dial indicator (6) into position until the point contacts gauge (8). Slide dial indicator
(6) until the needle of the dial indicator makes a quarter of a revolution clockwise. The
needle should be in a vertical position. Tighten bolt (5) and zero dial indicator (6) .
6. Place gauge body (7) on the spacer plate with the dial indicator point on the cylinder liner
flange. Read the dial indicator in order to find the amount of liner projection. Check the
liner projection at four locations (every 90 degrees) around each cylinder liner.
Table 3
Specifications
Liner Projection 0.033 mm (.0013 inch) to
0.175 mm (.0069 inch)
Maximum Variation in Each Cylinder
0.051 mm (.0020 inch)
Maximum Average Variation Between Adjacent Cylinders
0.051 mm (.0020 inch)
Maximum Variation Between All Cylinders
0.102 mm (.0040 inch)
7. If the cylinder liner projection is out of specification, rotate the cylinder liner in the bore and
repeat the procedure. If the cylinder liner projection measurements are again out of
specification, try installing the cylinder liner in a different cylinder bore to improve the
measurements.
Note: Do not exceed the maximum liner projection of 0.175 mm (0.0069 inch). Cracking in
the flange of the cylinder liner results from excessive cylinder liner projection
measurements.
8. If the maximum variation between cylinder liners is greater than the recommended
specification, shims must be used in order to reach the correct specification.
9. When the cylinder liner projection for each cylinder liner is within the recommended
specification, mark each cylinder liner for the proper location in the bore and remove the
cylinder liners.
10. Lubricate the O-ring seals, the cylinder liner, and the upper filler band before installation.
Note: If the lower O-ring seals are black in color, apply liquid soap on the lower O-ring
seals and the cylinder block. Use clean engine oil on the upper filler band.
Note: If the lower O-rings are brown in color, apply engine oil on the lower O-ring seals,
the cylinder block, and the upper filler band.
NOTICE
3/5(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Apply 5P-3975 Rubber Lubricant and/or clean engine oil immediately
before assembly. If the 5P-3975 Rubber Lubricant or engine oil is
applied too early, the filler bands and/or O-ring seals may swell and
the filler bands and/or O-ring seals may be pinched under the cylinder
liner during installation.
Illustration 3 g00544889
11. Apply liquid soap on the bottom cylinder liner bore in the cylinder block. Apply liquid soap
on the grooves of the cylinder liner and on O-ring seals (4). Install O-ring seals (4) on the
cylinder liner.
12. Lubricate filler band (5) with clean engine oil and install filler band (5) on cylinder liner (6).
Install cylinder liner (6) into the engine block immediately after you lubricate the cylinder
liner. This helps to prevent swelling of the filler band.
Illustration 4 g00478920
13. Ensure that the mark on the cylinder liner is in alignment with the mark on the cylinder
block. Use Tool (B) to press each of the cylinder liners into position.
End By:
4/5(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. a. Install the Pistons and Connecting Rods. Refer to Disassembly and Assembly, "Pistons and
Connecting Rods - Install".
b. Install the cylinder head. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 17 00:08:20 UTC+0800 2020
5/5(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 8FK
Configuration: 330 L, 330 LL & 330 FB FOREST SWING MACHINES 8FK00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01112806
Piston Cooling Jets - Remove and Install
SMCS - 1331-010
Removal Procedure
Start By:
A. Remove the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00473474
1/3(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. 1. Use a soft punch to remove piston cooling jet (1) from the cylinder block.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-7772 Driver 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: On the 3304B, the piston cooling jets are installed in the No. 2 and the No. 4 main bosses.
On the 3306B, the No. 2 and the No. 6 bosses for the main bearings have two jets. The No. 3 and
No. 5 bosses for the main bearings have one jet. A replacement is necessary if the jets are
damaged. Normally, it will only be necessary to ensure that the jets are clean.
Illustration 2 g00473474
1. Use Tool (A) to install piston cooling jet (1) with the small end first. Install the jets in the
bosses for the main bearing until the jets are against the counterbore.
2. Ensure that the passage is open after piston cooling jet (1) is installed.
End By: Install the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Sat Oct 17 00:09:16 UTC+0800 2020
2/3(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 8FK
Configuration: 330 L, 330 LL & 330 FB FOREST SWING MACHINES 8FK00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00976049
Pistons and Connecting Rods - Remove
SMCS - 1225-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2269 Ridge Reamer 1
Start By:
A. Remove the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and
Install".
B. Remove the engine oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan
Plate - Remove and Install".
C. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tool (A) to remove the liner wear ridge from the inner surface of the cylinder liner.
1/3(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Illustration 1 g00483120
2. Turn the crankshaft until two of the pistons are at the bottom center. Remove connecting rod
nuts (1) from the connecting rod. Remove connecting rod cap (2). Put identification marks
on the connecting rod and connecting rod cap. The identification marks must be on the
bearing tab side for installation purposes.
Illustration 2 g00483180
Illustration 3 g00496980
2/3(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. 3. After connecting rod cap (2) is removed, push connecting rod (3) away from the crankshaft
until the piston rings are out of the cylinder liners. Remove piston (4) from the cylinder
block.
4. Ensure that the connecting rod and the connecting rod cap are kept as a set. Put an
identification mark on each piston in order to locate the piston in the cylinder block.
5. Repeat Steps 1 through 4 for the remaining piston and connecting rods.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Oct 17 00:10:11 UTC+0800 2020
3/3(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 8FK
Configuration: 330 L, 330 LL & 330 FB FOREST SWING MACHINES 8FK00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00977166
Pistons and Connecting Rods - Disassemble
SMCS - 1225-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 7S-9470 Piston Ring Expander 1
B
5P-8639 Press Group 1
5P-8645 Adapter 1
6V-3029 Spacer 1
6V-2049 Adapter 1
1U-5230 Hand Hydraulic Pump 1
8F-0024 Hose 1
1P-2375 Connecting Coupler 1
1P-2376 Connecting Coupler 1
Start By:
A. Remove the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and
Connecting Rods - Remove".
NOTICE
1/4(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00484932
1. Remove the piston rings from the pistons with Tool (A) .
Illustration 2 g00484980
2. Remove retaining ring (3), piston pin (1) and connecting rod (2) .
3. Remove the connecting rod bearing.
4. Heat the connecting rod in an oven to a temperature of 176 to 260 °C (350 to 500 °F). Do
not use a direct flame to heat a connecting rod.
2/4(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 3 g00485038
Hot oil and hot components can cause personal injury. Do not allow hot
oil or hot components to contact the skin.
5. Put 6V-3029 Spacer (11) into the base plate. Put the connecting rod on the base plate of
Tool (B) .
6. Put the connecting rod piston pin bearing end in the center of the port assembly of Tool (B).
Install pin (5) in the center of the bore for the connecting rod bearing.
7. Install 6V-2049 Adapter (9). Align the hole in the adapter with the hole in the base plate of
Tool (B) .
8. Install clamp bar (10) and clamp pin (4) .
Note: The old piston pin bearing is removed while the new piston pin bearing is installed.
9. Put the new piston pin bearing on the connecting rod. Install 5P-8645 Adapter (8) with the
tapered end of the adapter toward the piston pin bearing. The piston pin bearing joint must
be in alignment with the hole in 6V-2049 Adapter (9) and the base plate of Tool (B) .
10. Install adapter (7) from the press group on adapter (11) .
11. Use Tool (B) to push the new piston pin bearing (6) into the connecting rod. Press piston pin
bearing (6) into position until adapter (8) makes contact with the connecting rod surface.
12. Remove the connecting rod and the old piston pin bearing from Tool (B) .
13. Check the piston pin bearing bore diameter after the bearing is installed. The correct inside
diameter is 43.210 ± 0.008 mm (1.7012 ± 0.0003 inch). The clearance between the bearing
and the piston pin must not be more than 0.08 mm (0.003 inch). Refer to Special Instruction,
SMHS7295 for additional information on removing the piston pin bearings.
Sat Oct 17 00:11:07 UTC+0800 2020
3/4(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 L EXCAVATOR 8FK
Configuration: 330 L, 330 LL & 330 FB FOREST SWING MACHINES 8FK00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00977179
Pistons and Connecting Rods - Assemble
SMCS - 1225-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 7S-9470 Piston Ring Expander 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the grooves of the used pistons with an acceptable tool or 1U-8811 Cleaner .
2. Install the connecting rod bearings. Ensure that the tabs on the back side of the connecting
rod bearings are in the tab grooves of the connecting rod and the connecting rod cap.
1/3(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
26. Illustration 1 g00486509
3. Install connecting rod (2) into the piston. Ensure that bearing tab slot (3) and the
identification marks are on the same side as the "V" mark on the top of the piston.
4. Lubricate piston pin (1) with clean engine oil and install piston pin (1) through the piston
and connecting rod. Install retaining ring (4) on the end of the piston pin.
Illustration 2 g00484932
5. Install the oil control ring on the piston with Tool (A) .
Note: The spring ends of the oil control ring should be assembled 180 degrees from the ring
end gap. The blue colored portion of the spring must be visible at the ring end gap.
6. Use Tool (A) to install the intermediate piston ring with the side marked "UP-2" toward the
top of the piston.
7. Use Tool (A) to install the top piston ring with the side marked "UP-1" toward the top of the
piston.
Note: The gaps in the intermediate piston ring and the top piston ring should be separated
by 120 degrees.
End By: Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons
and Connecting Rods - Install".
2/3(W)
w
2020/10/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...