This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It outlines the required tools and steps to remove the idler gear, idler shaft, thrust plate, and bushing. It also describes how to measure gear backlash and end play, and install the idler gear components. A separate section provides instructions for removing the front housing of the engine.
Caterpillar cat 323 d l excavator (prefix pbe) service repair manual (pbe0000...fjjsekmsmmes
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to re-install components in reverse order, checking backlash and end play tolerances.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...shudun96087
This document provides instructions for removing and installing the idler gear on the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear. The installation procedure specifies cleaning parts and aligning timing gear marks before installing the idler gear, thrust plate, and idler gear bolt. Tolerances for backlash and clearances are provided to check proper installation.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...qme229722
This document provides instructions for removing and installing the idler gear on the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear. The installation procedure specifies cleaning parts and aligning timing gear marks before installing the idler gear, thrust plate, and idler gear bolt. Tolerances for backlash and clearances are provided to check proper installation.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...kesi7153062
This document provides instructions for removing and installing the idler gear on the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear. The installation procedure specifies cleaning parts and aligning timing gear marks before installing the idler gear, thrust plate, and idler gear bolt. Tolerances for backlash and clearance measurements are provided to check proper installation.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on the shaft.
3) Checking gear backlash and end play measurements during installation.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...zan2736ban
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt, thrust plate, and idler gear using various tools. Clearances and backlash measurements are specified when installing the idler gear. Removing additional gears like the camshaft and crankshaft gears are also referenced. Proper containment of fluids and cleaning of parts are emphasized.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...fusjekkdmdmd2w
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines reinstalling these components and checking gear backlash and end play tolerances. Additional instructions are provided for removing and installing the front housing of the engine.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar cat 323 d l excavator (prefix pbe) service repair manual (pbe0000...fjjsekmsmmes
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to re-install components in reverse order, checking backlash and end play tolerances.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...shudun96087
This document provides instructions for removing and installing the idler gear on the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear. The installation procedure specifies cleaning parts and aligning timing gear marks before installing the idler gear, thrust plate, and idler gear bolt. Tolerances for backlash and clearances are provided to check proper installation.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...qme229722
This document provides instructions for removing and installing the idler gear on the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear. The installation procedure specifies cleaning parts and aligning timing gear marks before installing the idler gear, thrust plate, and idler gear bolt. Tolerances for backlash and clearances are provided to check proper installation.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...kesi7153062
This document provides instructions for removing and installing the idler gear on the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear. The installation procedure specifies cleaning parts and aligning timing gear marks before installing the idler gear, thrust plate, and idler gear bolt. Tolerances for backlash and clearance measurements are provided to check proper installation.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on the shaft.
3) Checking gear backlash and end play measurements during installation.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...zan2736ban
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt, thrust plate, and idler gear using various tools. Clearances and backlash measurements are specified when installing the idler gear. Removing additional gears like the camshaft and crankshaft gears are also referenced. Proper containment of fluids and cleaning of parts are emphasized.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...fusjekkdmdmd2w
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines reinstalling these components and checking gear backlash and end play tolerances. Additional instructions are provided for removing and installing the front housing of the engine.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on in reverse order of removal.
3) Checking gear backlash and end play measurements against specifications.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...f8usejkddmmd
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and installing the gear, thrust plate, washer and bolt.
3) Checking gear backlash and end play measurements during installation.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...ikdkdmddm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to install the bushing and idler shaft, then aligning the timing gears and checking backlash clearances.
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on in reverse order of removal.
3) Checking gear backlash and end play measurements against specifications.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...8ufjsekddm8u
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt, thrust plate, and idler gear using various tools. Clearances and backlash measurements are specified when installing the idler gear. Removing additional gears like the camshaft and crankshaft gears are also referenced. Proper containment of fluids and cleaning of parts are emphasized.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...ikdkdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...ufjksemd8ujd
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt, thrust plate, and idler gear using various tools. Clearances and backlash measurements are specified when installing the idler gear. Removing additional gears like the camshaft and crankshaft gears are also referenced. Proper containment of fluids and cleaning of parts are emphasized.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...km7seydwuhdw
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to install the bushing and idler shaft, and aligning timing gear marks when reinstalling the idler gear. Tolerances for backlash and clearances are provided.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...jdkskmdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using tools to install the bushing, idler shaft, idler gear, thrust plate, washer, and idler gear bolt while ensuring proper gear alignment and backlash. Tolerances for backlash and clearances are provided.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to install the bushing and idler shaft, and aligning timing gear marks when reinstalling the idler gear. Tolerances for backlash and clearances are provided.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...prmy389342
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear, idler shaft, thrust plate and washer. The installation procedure specifies cleaning parts and ensuring proper alignment of timing gear marks before pressing in a new bushing if needed, installing the idler shaft, gear, thrust plate and bolt. Tolerances for backlash and end play are provided to check installation.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fhjsjkdmemm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Installation involves reversing the removal steps and ensuring proper gear alignment and specifications are met. Additional documents are referenced for removing other gears in the front group.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...cdfzxs
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on in reverse order of removal.
3) Checking gear backlash and end play measurements against specifications.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fjjskmdmem
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Checks are made for wear on removed parts. The installation procedure specifies cleaning parts and aligning timing gear marks before pressing in a new bushing if needed, installing the idler shaft and gear, and torquing the idler gear bolt. Clearances and backlash are checked against specifications.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...dueikdkmem
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Installation involves reversing the removal steps and ensuring proper gear alignment and specifications are met. Additional documents are referenced for removing other gears in the front group.
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...zan2736ban
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
More Related Content
Similar to Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual Instant Download.pdf
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on in reverse order of removal.
3) Checking gear backlash and end play measurements against specifications.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...f8usejkddmmd
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and installing the gear, thrust plate, washer and bolt.
3) Checking gear backlash and end play measurements during installation.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...ikdkdmddm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to install the bushing and idler shaft, then aligning the timing gears and checking backlash clearances.
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on in reverse order of removal.
3) Checking gear backlash and end play measurements against specifications.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...8ufjsekddm8u
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt, thrust plate, and idler gear using various tools. Clearances and backlash measurements are specified when installing the idler gear. Removing additional gears like the camshaft and crankshaft gears are also referenced. Proper containment of fluids and cleaning of parts are emphasized.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...ikdkdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...ufjksemd8ujd
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt, thrust plate, and idler gear using various tools. Clearances and backlash measurements are specified when installing the idler gear. Removing additional gears like the camshaft and crankshaft gears are also referenced. Proper containment of fluids and cleaning of parts are emphasized.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...km7seydwuhdw
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to install the bushing and idler shaft, and aligning timing gear marks when reinstalling the idler gear. Tolerances for backlash and clearances are provided.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...jdkskmdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using tools to install the bushing, idler shaft, idler gear, thrust plate, washer, and idler gear bolt while ensuring proper gear alignment and backlash. Tolerances for backlash and clearances are provided.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to install the bushing and idler shaft, and aligning timing gear marks when reinstalling the idler gear. Tolerances for backlash and clearances are provided.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...prmy389342
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear, idler shaft, thrust plate and washer. The installation procedure specifies cleaning parts and ensuring proper alignment of timing gear marks before pressing in a new bushing if needed, installing the idler shaft, gear, thrust plate and bolt. Tolerances for backlash and end play are provided to check installation.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fhjsjkdmemm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Installation involves reversing the removal steps and ensuring proper gear alignment and specifications are met. Additional documents are referenced for removing other gears in the front group.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...cdfzxs
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on in reverse order of removal.
3) Checking gear backlash and end play measurements against specifications.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fjjskmdmem
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Checks are made for wear on removed parts. The installation procedure specifies cleaning parts and aligning timing gear marks before pressing in a new bushing if needed, installing the idler shaft and gear, and torquing the idler gear bolt. Clearances and backlash are checked against specifications.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...dueikdkmem
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Installation involves reversing the removal steps and ensuring proper gear alignment and specifications are met. Additional documents are referenced for removing other gears in the front group.
Similar to Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual Instant Download.pdf (20)
Caterpillar Cat 336D L Excavator (Prefix M4T) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions that include disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in the reverse order. Safety notices are provided regarding containing fluids, cleaning parts, and relieving hydraulic pressure before disassembly.
Caterpillar Cat 336D L Excavator (Prefix LMG) Service Repair Manual Instant D...zan2736ban
The document provides instructions for assembling a swivel component. It lists required tools including link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel joint on a repair stand, and reassembling parts like the outside housing, rotor, seals, bolts and washers in the correct order. Thorough cleaning of parts is important before assembly to prevent contamination.
Caterpillar Cat 336D L Excavator (Prefix L5X) Service Repair Manual Instant D...zan2736ban
This document provides instructions for removing and installing the rear gear group and flywheel on a 336D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and seals. Installation involves cleaning parts and using tools to carefully lower bearings and gears into place while matching specific dimensions, then reinstalling covers, seals, and bolts. Precautions are given to keep parts clean and properly position oil passages.
Caterpillar Cat 336D L Excavator (Prefix JWR) Service Repair Manual Instant D...zan2736ban
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It lists required tools and gives step-by-step instructions including disconnecting hoses, removing bolts and covers, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids, releasing pressure from the hydraulic system, and preventing contamination.
Caterpillar Cat 336D L Excavator (Prefix JRX) Service Repair Manual Instant D...zan2736ban
1) The document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit.
2) The disassembly procedure involves using various tools to remove 25 components of the final drive including gears, seals, plates, and housings.
3) The assembly procedure is the reverse of disassembly and provides instructions for installing the components using loctite and torquing bolts to the specified values.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...zan2736ban
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It outlines the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, lubricating seals, applying retaining compound to the sleeve, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or oil consumption issues.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...zan2736ban
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...zan2736ban
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix DTS) Service Repair Manual Instant D...zan2736ban
This document provides instructions for disassembling and assembling the piston pump of a 336D L excavator. The disassembly procedure involves removing 30 individual parts from the pump housing in a specific order. The assembly procedure describes installing the parts in the reverse order and notes that some components require special tools or heating/cooling to install properly. Precautions are provided to prevent injury from parts under spring tension.
Caterpillar Cat 336D and 336D L Excavator (Prefix MPL) Service Repair Manual ...zan2736ban
1. The document provides step-by-step instructions for disassembling and assembling the piston pump of a 336D excavator.
2. Disassembly involves removing over 30 individual parts in a specific order, including housings, seals, springs, pistons, and bearings.
3. Assembly requires carefully installing the parts in reverse order and adjusting shims and bearings to ensure proper clearance and operation.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...zan2736ban
1. The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. Removal and installation procedures are outlined in steps with accompanying illustrations. Cleanliness is emphasized and inspecting parts for wear or damage before reassembly.
3. Tools required are listed for some procedures. Proper lifting of heavy components like the hydraulic oil cooler is advised to prevent injury.
Caterpillar Cat 336D and 336D L Excavator (Prefix JBT) Service Repair Manual ...zan2736ban
The document provides instructions for servicing the piston pump (hydraulic fan) on a 336D excavator. It describes how to install the piston pump, connecting hoses and harness. It then details how to disassemble, remove and assemble the piston motor (hydraulic fan), including removing springs and pins, and replacing seals and bearings. Personal protective equipment is recommended when working with spring loaded parts.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix WBA) Service Repai...zan2736ban
The document provides instructions for disassembling a Caterpillar 330F L excavator travel motor. It lists 28 steps to completely disassemble the travel motor, including removing components like the head, springs, pistons, bearings, and housing. Various tools are required, including bolts, nuts, retaining rings, presses, and pullers to separate the individual parts in a specific sequence. Safety precautions are provided throughout to properly release pressures and contain fluids.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix JHF) Service Repai...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, and using shims to set the proper bearing preload when reassembling components. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar Cat 330F and 330F L Excavator (Prefix LCG) Service Repair Manual ...zan2736ban
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. It involves 37 steps to disassemble the final drive which includes removing gears, shafts, carriers, and housing components. The assembly process involves 33 steps including pressing in new bearings, installing seals, adjusting the bearing preload using shims, and reattaching the sprocket housing. Tools such as retaining ring pliers, eyebolts and a transmission repair stand are required. Precise measurements are taken to determine the correct shim thickness for proper bearing preload.
Caterpillar Cat 330F and 330F L Excavator (Prefix HCK) Service Repair Manual ...zan2736ban
The document provides instructions for disassembling a travel motor. It describes 28 steps to remove parts like the head, brake piston, rotating assembly, bearings, seals, and more. Various tools are required including bolts, nuts, retaining ring pliers, bearing pullers, and more. Safety notices are included to warn of potential spring forces or fluid hazards during disassembly.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...zan2736ban
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and containing fluids during disassembly.
Caterpillar Cat 330D2 L Excavator (Prefix ZBF) Service Repair Manual Instant ...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly, including gears, shafts, seals, and housings. The assembly section outlines 37 steps to reinstall these parts in reverse order, noting that cleanliness is important, old seals should be replaced, and parts should be lubricated before assembly. Precise measurements and shimming are required to set proper bearing preload when reinstalling the main housing.
Caterpillar Cat 330D2 L Excavator (Prefix SZK) Service Repair Manual Instant ...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330D2 L. The disassembly process involves using various tools to remove over 30 individual parts from the final drive assembly, including gears, shafts, seals, and housings. The assembly process similarly provides step-by-step instructions for installing the parts back onto the final drive, noting the importance of cleanliness and applying lubricants between parts. Proper bearing preload is achieved through measuring clearance and installing shims as needed.
Caterpillar Cat 330D2 L Excavator (Prefix PTE) Service Repair Manual Instant ...zan2736ban
This document provides instructions for removing and installing a turbocharger for top mounted engines. The removal process involves disconnecting hoses and tubes, removing bolts and nuts, and taking off the turbocharger assembly. For installation, components are cleaned and inspected, gaskets and seals are installed, bolts are tightened in a specified order and torque, and hoses/tubes are reconnected. Tools, safety notices, and illustrations are included to aid the process.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01374810
Illustration 6 g01374811
5. The following items are components of Tooling (A).
◦ 9U-6147 Stud (9)
◦ 6V-8231 Nut (10)
◦ 9U-6146 Sleeve Assembly (11)
◦ 8T-4244 Nut (12)
6. Use Tooling (A) in order to remove idler shaft (8) (not shown) from the cylinder block.
Check idler shaft (8) for wear and damage. Replace idler shaft (8), if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
◦ In order to remove camshaft gear (3), refer to Disassembly and Assembly, "Camshaft
- Remove".
◦ In order to remove fuel injection pump gear (1), refer to Disassembly and Assembly,
"Fuel Injection Pump - Remove".
◦ In order to remove the gear from the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Remove".
◦ In order to remove crankshaft gear (4), refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 16:54:48 UTC+0800 2020
4/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02879402
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
a 1p-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01374804
1. Use Tooling (A) and a suitable press in order to install a new bushing (7) (not shown), if the
bushing was removed.
Illustration 2 g01374810
2. Lower the temperature of idler shaft (8) . Install idler shaft (8) (not shown) onto the cylinder
block.
Note: When idler shaft (8) is installed, ensure that the oil hole of idler shaft (8) is up.
Illustration 3 g01374827
3. Install idler gear (2) onto idler shaft (8) .
2/5
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 4 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
Illustration 5 g01374789
4. Install thrust plate (6) onto the idler shaft.
5. Install the washer and idler gear bolt (5) onto thrust plate (6) . Tighten idler gear bolt (5) to a
torque of 34 ± 5 N·m (25 ± 4 lb ft).
3/5
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Note: See the following list for the installation of the other gears in the front gear group.
◦ In order to install the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Install".
◦ In order to install the fuel injection pump gear, refer to Disassembly and Assembly,
"Fuel Injection Pump - Install".
◦ In order to install the gear to the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Install".
◦ In order to install the crankshaft front gear, refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Illustration 6 g01374841
6. Install a dial indicator and rotate idler gear (2) back and forth in order to measure backlash.
Refer to Table 3.
Table 2
Item Standard at Assembly Service Limit
Backlash of crankshaft gear and
idler gear
0.510 to 0.157 mm (0.0201 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of camshaft gear and
idler gear
0.520 to 0.158 mm (0.0205 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of fuel injection pump
gear and idler gear
0.0560 to 0.205 mm (0.0022 to
0.0081 inch)
0.250 mm (0.0098
inch)
4/5
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. End play of idler gear
0.050 to 0.200 mm (0.0020 to
0.0079 inch)
0.350 mm (0.0138
inch)
Clearance between idler gear
bushing and shaft
0.009 to 0.050 mm (0.0004 to
0.0020 inch)
0.100 mm (0.0039
inch)
Illustration 7 g01374874
7. Measure the end play of idler gear (2) with a feeler gauge. Refer to Table 3.
End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 16:55:47 UTC+0800 2020
5/5
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02743335
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
a. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
b. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
c. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
d. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374908
1. Loosen hose clamp (1) that secures hose (2) to the front housing.
2. Disconnect hose (2) from the front housing.
Illustration 2 g00605985
3. Remove bolts (3) and the washers that hold front housing (4) to the plate and the cylinder
block.
2/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 4. Remove six bolts (5) (not shown) and the washers that mount front housing (4) to the oil
pan.
Illustration 3 g00606002
5. Remove bolts (6) and the washers that mount front housing (4) to front plate (8) and the
cylinder block.
6. Use two people in order to remove front housing (4) from the cylinder block and front plate
(8). The weight of front housing (4) is approximately 20 kg (45 lb).
Note: Check the condition of gasket (7) (not shown) for the engine oil pan. If gasket (7) is
damaged, it may be necessary to replace gasket (7). Refer to Disassembly and Assembly,
"Engine Oil Pan - Remove and Install" for replacement of gasket (7) for the engine oil pan.
3/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g01377884
7. Remove baffle plate (9).
Illustration 5 g01377894
8. Use Tooling (A) in order to remove crankshaft front seal (10) (not shown) from front
housing (4), if necessary.
9. Check the teeth of the timing gears for the following items: wear, nicks, chips and uneven
contact. Check the keyway for wear or damage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 16:56:47 UTC+0800 2020
4/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02879387
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets, and the seals for wear or for damage. Replace the components, if
necessary.
1/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00836619
Alignment marks for timing gears
1. Check the alignment of the timing gears.
Note: Ensure that the marks on the timing gears are in alignment. Align the "3" mark on the
fuel injection pump drive gear with the "33" mark on the idler gear. Make an alignment of
the "2" mark on the idler gear with the "22" mark on the camshaft gear. Align the "1" mark
on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top
center position when the timing marks are in alignment.
Illustration 2 g00606022
2. Ensure that the old gasket material (9) is removed from the mating surface of front housing
(4) and the timing gear plate. Install a new gasket (9) .
3. If the crankshaft front seal (10) (not shown) was removed, use Tooling (A) in order to
install a new crankshaft front seal (10) .
2/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00606002
4. Before installation of front housing (4) , check gasket (7) (not shown) for the oil pan for
damage. Replace gasket (7) , if necessary. Refer to Disassembly and Assembly, "Engine Oil
Pan - Remove and Install" for replacement of gasket (7) for the engine oil pan.
5. Use two people in order to install front housing (4) onto front plate (8) and the cylinder
block. The weight of front housing (4) is approximately 20 kg (45 lb).
6. Install bolts (6) in order to fasten front housing (4) onto the cylinder block and front plate
(8) .
Illustration 4 g00605985
7. Install the washers and six bolts (5) (not shown) in order to secure front housing (4) onto
engine oil pan.
3/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 8. Install bolts (3) and washers that secure front housing (4) to the front plate and the cylinder
block.
Illustration 5 g01374908
9. Connect hose (2) to the front housing.
10. Tighten hose clamp (1) in order to secure hose (2) to the front housing.
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
c. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
d. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 16:57:46 UTC+0800 2020
4/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01615486
Front Plate - Remove
SMCS - 1163-011
Removal Procedure
Start By:
a. Remove the idler gear. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove".
b. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
c. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00611711
1. Remove one bolt (1) and the washer from the front plate (2).
2. Remove front plate (2) from the engine.
3. Remove gasket (3) (not shown) from the engine or from the front plate (2).
Note: Ensure that all mating surfaces are clear of old gaskets.
Note: Check the cylinder block for the following conditions: scale buildup, corrosion and
other damage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 16:58:45 UTC+0800 2020
2/2
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01576831
Front Plate - Install
SMCS - 1163-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611711
1. Place gasket (3) (not shown) in position on the engine.
Note: Ensure that all mating surfaces are clear of old gaskets.
2. Place front plate (2) in position on the engine.
1/2
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 3. Install one bolt (1) and the washer in order to secure front plate (2) to the engine. Tighten
the bolt to a torque of 35 ± 5 N·m (26 ± 4 lb ft).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
c. Install the idler gear. Refer to Disassembly and Assembly, "Gear Group (Front) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 16:59:44 UTC+0800 2020
2/2
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02879389
Crankcase Breather - Remove and Install
SMCS - 1317-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g01374569
1. Loosen clamps (3) and remove hose (2) .
2. Remove breather assembly (1) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01374569
1. Install new breather assembly (1) .
2. Install hose (2) and tighten hose clamps (3) .
Sun Aug 30 17:00:44 UTC+0800 2020
2/3
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742668
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01374565
1/2
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. 1. Loosen clamp (2) and disconnect hose (1).
2. Remove bolts (4) and remove valve mechanism cover (3) and the O-ring seal.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01374565
1. Position valve mechanism cover (3) and the O-ring seal. Install bolts (4). Tighten bolts (4)
to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
2. Connect hose (1) and tighten clamp (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 17:01:43 UTC+0800 2020
2/2
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...