This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fjjskekdmmem
This document provides instructions for removing and installing the idler gear on the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear, idler shaft, thrust plate, and bushing. The installation procedure specifies cleaning and inspecting parts, pressing in a new bushing if needed, installing the idler gear and shaft, checking backlash and end play, and aligning timing gear marks.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...fksjksmmde
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Installing involves pressing in a new idler gear bushing if needed, lowering the idler shaft temperature, and installing the idler gear, thrust plate, washer and bolt while checking backlash and end play
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...tuzhiyou2
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and using a puller tool to remove the idler gear and shaft.
2) Installing the idler gear by pressing in a new bushing if needed, installing the shaft, gear, thrust plate, washer and bolt, and checking backlash and end play measurements.
3) The document is part of a service manual and provides maintenance instructions for technicians working on Caterpillar engines.
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and using a puller tool to remove the idler gear and shaft.
2) Installing the idler gear by pressing in a new bushing if needed, installing the shaft, gear, thrust plate, washer and bolt, and checking backlash and end play measurements.
3) The document is part of a service manual and provides maintenance instructions for technicians working on Caterpillar engines.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...qfyc504378
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar C4.2 engine.
The idler gear removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The idler gear installation is the reverse of removal. Tolerances and specifications for components are provided.
The front housing removal requires removing several other components first, then removing bolts and separating the housing. Installation involves reversing the removal steps and checking gaskets and seals.
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal procedure for the front housing includes removing components attached to the housing like the alternator and fuel injection pump. It also provides instructions for removing housing mounting bolts and removing the front housing from the engine.
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal of the front housing requires removing several other engine components first then removing bolts and the housing. The installation of the front housing involves installing seals, bolts and other components.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fjjskekdmmem
This document provides instructions for removing and installing the idler gear on the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear, idler shaft, thrust plate, and bushing. The installation procedure specifies cleaning and inspecting parts, pressing in a new bushing if needed, installing the idler gear and shaft, checking backlash and end play, and aligning timing gear marks.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...fksjksmmde
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Installing involves pressing in a new idler gear bushing if needed, lowering the idler shaft temperature, and installing the idler gear, thrust plate, washer and bolt while checking backlash and end play
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...tuzhiyou2
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and using a puller tool to remove the idler gear and shaft.
2) Installing the idler gear by pressing in a new bushing if needed, installing the shaft, gear, thrust plate, washer and bolt, and checking backlash and end play measurements.
3) The document is part of a service manual and provides maintenance instructions for technicians working on Caterpillar engines.
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and using a puller tool to remove the idler gear and shaft.
2) Installing the idler gear by pressing in a new bushing if needed, installing the shaft, gear, thrust plate, washer and bolt, and checking backlash and end play measurements.
3) The document is part of a service manual and provides maintenance instructions for technicians working on Caterpillar engines.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...qfyc504378
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar C4.2 engine.
The idler gear removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The idler gear installation is the reverse of removal. Tolerances and specifications for components are provided.
The front housing removal requires removing several other components first, then removing bolts and separating the housing. Installation involves reversing the removal steps and checking gaskets and seals.
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal procedure for the front housing includes removing components attached to the housing like the alternator and fuel injection pump. It also provides instructions for removing housing mounting bolts and removing the front housing from the engine.
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal of the front housing requires removing several other engine components first then removing bolts and the housing. The installation of the front housing involves installing seals, bolts and other components.
This document provides instructions for disassembling and assembling the final drive of an excavator. It lists the required tools and parts. The disassembly process involves removing 37 individual components in a specific order, including gears, shafts, seals, washers, and housings. The assembly section provides instructions for installing these components in reverse order and notes on cleaning, lubricating, and setting proper bearing preload using shims.
Caterpillar Cat 325D L Excavator (Prefix GBR) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions to disassemble a final drive over 33 steps. Key steps include removing the cover, gears, carrier assemblies, planetary gears, and seals. Cleanliness is important to prevent dirt entering during disassembly. Various tools are required including a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The total weight of disassembled parts is provided.
Caterpillar Cat 323D L Excavator (Prefix JLG) Service Repair Manual Instant D...fujkskemdmdm4r
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts for a C6.4 engine. It describes the required tools and steps to remove the old inserts and install new ones.
2. Procedures are provided for removing, disassembling, and assembling the engine oil cooler. Parts are to be kept clean from contaminants to prevent damage.
3. Instructions are given for removing and installing the engine oil relief valve, including replacing the gasket. Cleanliness is important to prevent premature wear.
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D L excavator. The disassembly process involves using tools to remove retaining rings, seals, bearings, pistons and other components. The assembly process specifies cleaning parts and provides 30 steps for installing components in the correct order and ensuring proper operation, including adjusting end play and installing springs and seals.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions emphasize cleaning parts and ensuring they are reinstalled in their original locations to avoid damage and contamination.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345D L Excavator (Prefix RAJ) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, plates, seals, and piston assemblies. The disassembly process is described in 31 steps. The assembly section then lists 13 steps to reinstall components in reverse order, making sure to clean parts and apply new seals and lubricants.
This document provides instructions for removing and installing fuel injection pumps and disassembling and assembling fuel ratio control components on a Caterpillar 3406C diesel engine. The steps include using various tools to remove the fuel injection pumps from the pump housing, install new pumps, and check pump installation. Instructions are also provided to disassemble the fuel ratio control housing by removing bolts, springs, diaphragms and other parts and cleaning components before reassembly.
Caterpillar Cat 345C and 345C L Excavator (Prefix BWY) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, disks, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, spacers, pistons, plates and tightening components. Precautions are provided to keep parts clean and in correct orientation to prevent contamination of the hydraulic system.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
The document provides instructions for removing and installing the drive shaft group with retarder on a 621E, 623E, or 627E tractor. It describes disconnecting hydraulic lines and removing bolts, covers, and housing to access the drive shaft group. Special care must be taken when removing plates and springs from the retarder, as they are under pressure. The process is reversed for installation, reconnecting hydraulic lines and replacing removed components.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix WBC) Service Repair Manua...fujkskemdmdm4r
The document provides instructions for removing and installing various engine components, including:
- Valve guides are removed from the cylinder head using a valve guide driver tool. New guides are installed using driver tools until the proper height is reached.
- Valve seat inserts are removed from the cylinder head using extractors. New inserts are installed using a driver tool after being cooled.
- The engine oil filter base, oil filter, and oil cooler are removed. Hoses are disconnected and bolts removed to access these components.
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission housing, installing planetary gears and carriers, and attaching the transmission cover, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 350 and 350 L Excavator (Prefix 8HK) Service Repair Manual In...fujkskemdmdm4r
The document provides instructions for removing and installing various engine components on a 350-A EXCAVATOR 8HK excavator powered by a 3306 engine, including:
- Removing the cylinder head by first removing the fuel injection lines, exhaust manifold, rocker shaft and pushrods, then removing bolts and lifting the cylinder head off the engine block.
- Instructions for disassembling, assembling, and installing the rocker shaft, including removing/installing rocker arms, supports, springs and O-rings.
- Steps for installing a compression brake on the engine, including installing brackets, bolts and connecting wires.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tools. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Caterpillar Cat 350 and 350 L Excavator (Prefix 3ML) Service Repair Manual In...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the governor of a 350-A excavator powered by a 3306 engine. The disassembly process involves removing 34 parts from the governor including the fuel ratio control, housing, springs, levers, pins, plates, screws, solenoid, shaft and other components. The assembly process describes installing these 34 parts in the reverse order and includes ensuring parts are clean and lubricated before installation. Special tools are required for some steps.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
This document provides instructions for disassembling and assembling the final drive of an excavator. It lists the required tools and parts. The disassembly process involves removing 37 individual components in a specific order, including gears, shafts, seals, washers, and housings. The assembly section provides instructions for installing these components in reverse order and notes on cleaning, lubricating, and setting proper bearing preload using shims.
Caterpillar Cat 325D L Excavator (Prefix GBR) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions to disassemble a final drive over 33 steps. Key steps include removing the cover, gears, carrier assemblies, planetary gears, and seals. Cleanliness is important to prevent dirt entering during disassembly. Various tools are required including a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The total weight of disassembled parts is provided.
Caterpillar Cat 323D L Excavator (Prefix JLG) Service Repair Manual Instant D...fujkskemdmdm4r
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts for a C6.4 engine. It describes the required tools and steps to remove the old inserts and install new ones.
2. Procedures are provided for removing, disassembling, and assembling the engine oil cooler. Parts are to be kept clean from contaminants to prevent damage.
3. Instructions are given for removing and installing the engine oil relief valve, including replacing the gasket. Cleanliness is important to prevent premature wear.
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D L excavator. The disassembly process involves using tools to remove retaining rings, seals, bearings, pistons and other components. The assembly process specifies cleaning parts and provides 30 steps for installing components in the correct order and ensuring proper operation, including adjusting end play and installing springs and seals.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions emphasize cleaning parts and ensuring they are reinstalled in their original locations to avoid damage and contamination.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345D L Excavator (Prefix RAJ) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, plates, seals, and piston assemblies. The disassembly process is described in 31 steps. The assembly section then lists 13 steps to reinstall components in reverse order, making sure to clean parts and apply new seals and lubricants.
This document provides instructions for removing and installing fuel injection pumps and disassembling and assembling fuel ratio control components on a Caterpillar 3406C diesel engine. The steps include using various tools to remove the fuel injection pumps from the pump housing, install new pumps, and check pump installation. Instructions are also provided to disassemble the fuel ratio control housing by removing bolts, springs, diaphragms and other parts and cleaning components before reassembly.
Caterpillar Cat 345C and 345C L Excavator (Prefix BWY) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, disks, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, spacers, pistons, plates and tightening components. Precautions are provided to keep parts clean and in correct orientation to prevent contamination of the hydraulic system.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
The document provides instructions for removing and installing the drive shaft group with retarder on a 621E, 623E, or 627E tractor. It describes disconnecting hydraulic lines and removing bolts, covers, and housing to access the drive shaft group. Special care must be taken when removing plates and springs from the retarder, as they are under pressure. The process is reversed for installation, reconnecting hydraulic lines and replacing removed components.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix WBC) Service Repair Manua...fujkskemdmdm4r
The document provides instructions for removing and installing various engine components, including:
- Valve guides are removed from the cylinder head using a valve guide driver tool. New guides are installed using driver tools until the proper height is reached.
- Valve seat inserts are removed from the cylinder head using extractors. New inserts are installed using a driver tool after being cooled.
- The engine oil filter base, oil filter, and oil cooler are removed. Hoses are disconnected and bolts removed to access these components.
Caterpillar Cat 336D L Excavator (Prefix PTB) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides assembly instructions for a 336D L excavator transmission in 3 sentences:
It lists the required tools and parts, gives step-by-step instructions for assembling the transmission housing, installing planetary gears and carriers, and attaching the transmission cover, and notes that cleanliness is important during assembly and O-rings and seals should always be replaced.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 350 and 350 L Excavator (Prefix 8HK) Service Repair Manual In...fujkskemdmdm4r
The document provides instructions for removing and installing various engine components on a 350-A EXCAVATOR 8HK excavator powered by a 3306 engine, including:
- Removing the cylinder head by first removing the fuel injection lines, exhaust manifold, rocker shaft and pushrods, then removing bolts and lifting the cylinder head off the engine block.
- Instructions for disassembling, assembling, and installing the rocker shaft, including removing/installing rocker arms, supports, springs and O-rings.
- Steps for installing a compression brake on the engine, including installing brackets, bolts and connecting wires.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tools. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Caterpillar Cat 350 and 350 L Excavator (Prefix 3ML) Service Repair Manual In...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the governor of a 350-A excavator powered by a 3306 engine. The disassembly process involves removing 34 parts from the governor including the fuel ratio control, housing, springs, levers, pins, plates, screws, solenoid, shaft and other components. The assembly process describes installing these 34 parts in the reverse order and includes ensuring parts are clean and lubricated before installation. Special tools are required for some steps.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01374810
Illustration 6 g01374811
5. The following items are components of Tooling (A).
◦ 9U-6147 Stud (9)
◦ 6V-8231 Nut (10)
◦ 9U-6146 Sleeve Assembly (11)
◦ 8T-4244 Nut (12)
6. Use Tooling (A) in order to remove idler shaft (8) (not shown) from the cylinder block.
Check idler shaft (8) for wear and damage. Replace idler shaft (8), if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
◦ In order to remove camshaft gear (3), refer to Disassembly and Assembly, "Camshaft
- Remove".
◦ In order to remove fuel injection pump gear (1), refer to Disassembly and Assembly,
"Fuel Injection Pump - Remove".
◦ In order to remove the gear from the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Remove".
◦ In order to remove crankshaft gear (4), refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:32:55 UTC+0800 2020
4/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879402
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
a 1p-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01374804
1. Use Tooling (A) and a suitable press in order to install a new bushing (7) (not shown), if the
bushing was removed.
Illustration 2 g01374810
2. Lower the temperature of idler shaft (8) . Install idler shaft (8) (not shown) onto the cylinder
block.
Note: When idler shaft (8) is installed, ensure that the oil hole of idler shaft (8) is up.
Illustration 3 g01374827
3. Install idler gear (2) onto idler shaft (8) .
2/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 4 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
Illustration 5 g01374789
4. Install thrust plate (6) onto the idler shaft.
5. Install the washer and idler gear bolt (5) onto thrust plate (6) . Tighten idler gear bolt (5) to a
torque of 34 ± 5 N·m (25 ± 4 lb ft).
3/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Note: See the following list for the installation of the other gears in the front gear group.
◦ In order to install the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Install".
◦ In order to install the fuel injection pump gear, refer to Disassembly and Assembly,
"Fuel Injection Pump - Install".
◦ In order to install the gear to the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Install".
◦ In order to install the crankshaft front gear, refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Illustration 6 g01374841
6. Install a dial indicator and rotate idler gear (2) back and forth in order to measure backlash.
Refer to Table 3.
Table 2
Item Standard at Assembly Service Limit
Backlash of crankshaft gear and
idler gear
0.510 to 0.157 mm (0.0201 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of camshaft gear and
idler gear
0.520 to 0.158 mm (0.0205 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of fuel injection pump
gear and idler gear
0.0560 to 0.205 mm (0.0022 to
0.0081 inch)
0.250 mm (0.0098
inch)
4/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. End play of idler gear
0.050 to 0.200 mm (0.0020 to
0.0079 inch)
0.350 mm (0.0138
inch)
Clearance between idler gear
bushing and shaft
0.009 to 0.050 mm (0.0004 to
0.0020 inch)
0.100 mm (0.0039
inch)
Illustration 7 g01374874
7. Measure the end play of idler gear (2) with a feeler gauge. Refer to Table 3.
End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:33:54 UTC+0800 2020
5/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02743335
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
a. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
b. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
c. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
d. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374908
1. Loosen hose clamp (1) that secures hose (2) to the front housing.
2. Disconnect hose (2) from the front housing.
Illustration 2 g00605985
3. Remove bolts (3) and the washers that hold front housing (4) to the plate and the cylinder
block.
2/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 4. Remove six bolts (5) (not shown) and the washers that mount front housing (4) to the oil
pan.
Illustration 3 g00606002
5. Remove bolts (6) and the washers that mount front housing (4) to front plate (8) and the
cylinder block.
6. Use two people in order to remove front housing (4) from the cylinder block and front plate
(8). The weight of front housing (4) is approximately 20 kg (45 lb).
Note: Check the condition of gasket (7) (not shown) for the engine oil pan. If gasket (7) is
damaged, it may be necessary to replace gasket (7). Refer to Disassembly and Assembly,
"Engine Oil Pan - Remove and Install" for replacement of gasket (7) for the engine oil pan.
3/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g01377884
7. Remove baffle plate (9).
Illustration 5 g01377894
8. Use Tooling (A) in order to remove crankshaft front seal (10) (not shown) from front
housing (4), if necessary.
9. Check the teeth of the timing gears for the following items: wear, nicks, chips and uneven
contact. Check the keyway for wear or damage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:34:53 UTC+0800 2020
4/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879387
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets, and the seals for wear or for damage. Replace the components, if
necessary.
1/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00836619
Alignment marks for timing gears
1. Check the alignment of the timing gears.
Note: Ensure that the marks on the timing gears are in alignment. Align the "3" mark on the
fuel injection pump drive gear with the "33" mark on the idler gear. Make an alignment of
the "2" mark on the idler gear with the "22" mark on the camshaft gear. Align the "1" mark
on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top
center position when the timing marks are in alignment.
Illustration 2 g00606022
2. Ensure that the old gasket material (9) is removed from the mating surface of front housing
(4) and the timing gear plate. Install a new gasket (9) .
3. If the crankshaft front seal (10) (not shown) was removed, use Tooling (A) in order to
install a new crankshaft front seal (10) .
2/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00606002
4. Before installation of front housing (4) , check gasket (7) (not shown) for the oil pan for
damage. Replace gasket (7) , if necessary. Refer to Disassembly and Assembly, "Engine Oil
Pan - Remove and Install" for replacement of gasket (7) for the engine oil pan.
5. Use two people in order to install front housing (4) onto front plate (8) and the cylinder
block. The weight of front housing (4) is approximately 20 kg (45 lb).
6. Install bolts (6) in order to fasten front housing (4) onto the cylinder block and front plate
(8) .
Illustration 4 g00605985
7. Install the washers and six bolts (5) (not shown) in order to secure front housing (4) onto
engine oil pan.
3/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 8. Install bolts (3) and washers that secure front housing (4) to the front plate and the cylinder
block.
Illustration 5 g01374908
9. Connect hose (2) to the front housing.
10. Tighten hose clamp (1) in order to secure hose (2) to the front housing.
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
c. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
d. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:35:52 UTC+0800 2020
4/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i01615486
Front Plate - Remove
SMCS - 1163-011
Removal Procedure
Start By:
a. Remove the idler gear. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove".
b. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
c. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00611711
1. Remove one bolt (1) and the washer from the front plate (2).
2. Remove front plate (2) from the engine.
3. Remove gasket (3) (not shown) from the engine or from the front plate (2).
Note: Ensure that all mating surfaces are clear of old gaskets.
Note: Check the cylinder block for the following conditions: scale buildup, corrosion and
other damage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:36:52 UTC+0800 2020
2/2
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i01576831
Front Plate - Install
SMCS - 1163-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611711
1. Place gasket (3) (not shown) in position on the engine.
Note: Ensure that all mating surfaces are clear of old gaskets.
2. Place front plate (2) in position on the engine.
1/2
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 3. Install one bolt (1) and the washer in order to secure front plate (2) to the engine. Tighten
the bolt to a torque of 35 ± 5 N·m (26 ± 4 lb ft).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
c. Install the idler gear. Refer to Disassembly and Assembly, "Gear Group (Front) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:37:51 UTC+0800 2020
2/2
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879389
Crankcase Breather - Remove and Install
SMCS - 1317-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g01374569
1. Loosen clamps (3) and remove hose (2) .
2. Remove breather assembly (1) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01374569
1. Install new breather assembly (1) .
2. Install hose (2) and tighten hose clamps (3) .
Wed May 27 08:38:50 UTC+0800 2020
2/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768517
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01384853
1. Remove bolts (1) and remove cover (2) .
1/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. Illustration 2 g01385013
2. Disconnect hose (3) .
3. Remove bolts (4) and remove valve mechanism cover (5) and the O-ring seal.
Installation Procedure
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01385013
1. Position valve mechanism cover (5) and the O-ring seal. Install bolts (4). Tighten bolts (4)
to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
2/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 2. Connect hose (3) .
Illustration 4 g01384853
3. Position cover (2) and install bolts (1). Tighten bolts (1) to a torque of 17 ± 2 N·m (13 ± 1 lb
ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:39:50 UTC+0800 2020
3/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...