This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Installation involves reversing the removal steps and ensuring proper gear alignment and specifications are met. Additional documents are referenced for removing other gears in the front group.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
Caterpillar cat 314 d lcr excavator (prefix pdp) service repair manual (pdp00...soeldksejdksem
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing a new bushing if needed and lowering the idler shaft temperature before installing the shaft, idler gear, thrust plate, washer and bolt.
3) Checking backlash and end play measurements during installation.
Caterpillar cat 305.5 e2 cr mini hydraulic excavator (prefix nc5) service rep...cdfzxs
The document provides instructions for removing and installing various engine components of a 305.5E2 CR Mini Hydraulic Excavator powered by a C2.4 engine, including the inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil pump, water pump, and water temperature regulator. The procedures include draining fluids, removing fasteners and hoses, cleaning parts, and installing components in reverse order of removal while following safety notices.
The document provides instructions for removing and installing a cylinder head on a 3054C engine. Key steps include:
1. Draining fluids, removing related components like the exhaust manifold and fuel injectors before removing the cylinder head.
2. Gradually loosening and removing cylinder head bolts in reverse order to prevent distortion, then lifting off the head using a lifting device.
3. Cleaning the cylinder block and head mating surfaces, installing a new gasket and dowel pins before positioning the head back on using guide bolts for alignment.
4. Reinstalling the bolts and tightening them in stages to the specified torque in numerical order.
Caterpillar cat 312 e excavator (prefix pzl) service repair manual (pzl00001 ...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a 312E or 312E L excavator with a C4.4 engine. The key steps include:
1. Locking the crankshaft and fuel injection pump gear in position using timing pins.
2. Loosening the rocker arm inserts to fully close the valves.
3. Removing the camshaft, idler, and housing gears in the proper order while maintaining timing marks.
4. Cleaning and inspecting components before installing in reverse order while ensuring proper gear mesh and end play measurements.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...pfiskdmjekm
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Measuring gear backlash and end play during installation and comparing to specifications.
Caterpillar cat 314 d lcr excavator (prefix pdp) service repair manual (pdp00...soeldksejdksem
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing a new bushing if needed and lowering the idler shaft temperature before installing the shaft, idler gear, thrust plate, washer and bolt.
3) Checking backlash and end play measurements during installation.
Caterpillar cat 305.5 e2 cr mini hydraulic excavator (prefix nc5) service rep...cdfzxs
The document provides instructions for removing and installing various engine components of a 305.5E2 CR Mini Hydraulic Excavator powered by a C2.4 engine, including the inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil pump, water pump, and water temperature regulator. The procedures include draining fluids, removing fasteners and hoses, cleaning parts, and installing components in reverse order of removal while following safety notices.
The document provides instructions for removing and installing a cylinder head on a 3054C engine. Key steps include:
1. Draining fluids, removing related components like the exhaust manifold and fuel injectors before removing the cylinder head.
2. Gradually loosening and removing cylinder head bolts in reverse order to prevent distortion, then lifting off the head using a lifting device.
3. Cleaning the cylinder block and head mating surfaces, installing a new gasket and dowel pins before positioning the head back on using guide bolts for alignment.
4. Reinstalling the bolts and tightening them in stages to the specified torque in numerical order.
Caterpillar cat 312 e excavator (prefix pzl) service repair manual (pzl00001 ...fjjskekdmmse
This document provides instructions for removing and installing the front gear group on a 312E or 312E L excavator with a C4.4 engine. The key steps include:
1. Locking the crankshaft and fuel injection pump gear in position using timing pins.
2. Loosening the rocker arm inserts to fully close the valves.
3. Removing the camshaft, idler, and housing gears in the proper order while maintaining timing marks.
4. Cleaning and inspecting components before installing in reverse order while ensuring proper gear mesh and end play measurements.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 320 excavator models. It describes the required tools and gives a step-by-step process including removing clips and pins, sliding tubes, and removing/installing parts like the governor, linkage, and seals using special tools. References are provided for more information on governors and linkage inspection procedures.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fjjskekdmmem
This document provides instructions for removing and installing the idler gear on the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear, idler shaft, thrust plate, and bushing. The installation procedure specifies cleaning and inspecting parts, pressing in a new bushing if needed, installing the idler gear and shaft, checking backlash and end play, and aligning timing gear marks.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...fksjksmmde
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Installing involves pressing in a new idler gear bushing if needed, lowering the idler shaft temperature, and installing the idler gear, thrust plate, washer and bolt while checking backlash and end play
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...tuzhiyou2
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and using a puller tool to remove the idler gear and shaft.
2) Installing the idler gear by pressing in a new bushing if needed, installing the shaft, gear, thrust plate, washer and bolt, and checking backlash and end play measurements.
3) The document is part of a service manual and provides maintenance instructions for technicians working on Caterpillar engines.
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and using a puller tool to remove the idler gear and shaft.
2) Installing the idler gear by pressing in a new bushing if needed, installing the shaft, gear, thrust plate, washer and bolt, and checking backlash and end play measurements.
3) The document is part of a service manual and provides maintenance instructions for technicians working on Caterpillar engines.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...qfyc504378
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar C4.2 engine.
The idler gear removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The idler gear installation is the reverse of removal. Tolerances and specifications for components are provided.
The front housing removal requires removing several other components first, then removing bolts and separating the housing. Installation involves reversing the removal steps and checking gaskets and seals.
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal procedure for the front housing includes removing components attached to the housing like the alternator and fuel injection pump. It also provides instructions for removing housing mounting bolts and removing the front housing from the engine.
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal of the front housing requires removing several other engine components first then removing bolts and the housing. The installation of the front housing involves installing seals, bolts and other components.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...lituo39419496
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal of the front housing requires removing several other engine components first then removing bolts and the housing. The installation of the front housing involves installing seals, bolts and other components.
Caterpillar cat 314 d cr excavator (prefix pdp) service repair manual (pdp000...fhsjejkdmem
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar cat 314 d lcr excavator (prefix pdp) service repair manual (pdp00...fhsejkdkmem
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar cat 314 d lcr excavator (prefix pdp) service repair manual (pdp00...fhsjekkdkem
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar cat 314 d cr excavator (prefix pdp) service repair manual (pdp000...fjjsekdmme
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar Cat 314D CR and 314D LCR Excavator (Prefix PDP) Service Repair Ma...fijsekkdmdm2w
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. The removal procedure includes using various tools to remove the idler gear, idler shaft, and front housing. The installation procedure outlines installing the idler gear, checking gear backlash and end play, and installing the front housing.
Caterpillar Cat 314D CR and 314D LCR Excavator (Prefix PDP) Service Repair Ma...zan2736ban
The document provides instructions for removing and installing an idler gear on the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt and washer, thrust plate, and idler gear. It notes to check the idler shaft for wear and replace if needed. Instructions are also provided for installing the idler gear, including measuring backlash and end play.
Bomag bw 154 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 154 ac 4 tandem rollers service repair manualfhjsjkdmemm
The document provides technical specifications and adjustment values for Tandem Rollers models BW 141 AD Serie 4 and BW 154 AD Serie 4. It includes details on the engine, travel pump, travel motors, drum reduction gear, vibration pump, vibration motor, steering and charge pump, and filling capacities. The specifications are broken out by component and include information like component type, system, displacement, pressure levels, speeds, ratios, and approved lubricants.
Bomag bw 151 ad 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The safety section emphasizes that the machine must only be used for its intended purposes of compacting asphalt and soil and stresses the importance of following all safety instructions.
Bomag bw 151 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 151 ac 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The safety section emphasizes that the machine must only be used for its intended purposes of compacting asphalt and soil and stresses the importance of following all safety instructions.
Bomag bw 141 ad 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The technical data section specifies the dimensions, weights, engine, and other technical specifications for each roller model.
Bomag bw 141 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 141 ac 4 tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD Serie 4, BW 154 AD Serie 4, and BW 154 AD AM Serie 4. It includes specifications for the Deutz diesel engine, travel pump and motors, vibration pump and motors, steering pump, and filling capacities. The data is presented in a table format with specifications such as engine power, pump displacement volumes, pressure settings, and fluid capacities.
More Related Content
Similar to Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl00001 and up)
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fjjskekdmmem
This document provides instructions for removing and installing the idler gear on the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear, idler shaft, thrust plate, and bushing. The installation procedure specifies cleaning and inspecting parts, pressing in a new bushing if needed, installing the idler gear and shaft, checking backlash and end play, and aligning timing gear marks.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...fksjksmmde
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the front housing, idler gear bolt and washer, thrust plate, and idler gear from the idler gear shaft.
2) Using a puller tool to remove the idler gear bushing and idler shaft from the cylinder block.
3) Checking the idler shaft for wear and replacing if needed.
4) Installing involves pressing in a new idler gear bushing if needed, lowering the idler shaft temperature, and installing the idler gear, thrust plate, washer and bolt while checking backlash and end play
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...tuzhiyou2
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and using a puller tool to remove the idler gear and shaft.
2) Installing the idler gear by pressing in a new bushing if needed, installing the shaft, gear, thrust plate, washer and bolt, and checking backlash and end play measurements.
3) The document is part of a service manual and provides maintenance instructions for technicians working on Caterpillar engines.
The document provides instructions for removing and installing the idler gear of the front gear group on a Caterpillar C4.2 engine. It describes in detail:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and using a puller tool to remove the idler gear and shaft.
2) Installing the idler gear by pressing in a new bushing if needed, installing the shaft, gear, thrust plate, washer and bolt, and checking backlash and end play measurements.
3) The document is part of a service manual and provides maintenance instructions for technicians working on Caterpillar engines.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...qfyc504378
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar C4.2 engine.
The idler gear removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The idler gear installation is the reverse of removal. Tolerances and specifications for components are provided.
The front housing removal requires removing several other components first, then removing bolts and separating the housing. Installation involves reversing the removal steps and checking gaskets and seals.
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal procedure for the front housing includes removing components attached to the housing like the alternator and fuel injection pump. It also provides instructions for removing housing mounting bolts and removing the front housing from the engine.
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal of the front housing requires removing several other engine components first then removing bolts and the housing. The installation of the front housing involves installing seals, bolts and other components.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...lituo39419496
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 312D excavator engine. The removal procedure for the idler gear involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines installing the idler gear, thrust plate, washer and idler gear bolt. The removal of the front housing requires removing several other engine components first then removing bolts and the housing. The installation of the front housing involves installing seals, bolts and other components.
Caterpillar cat 314 d cr excavator (prefix pdp) service repair manual (pdp000...fhsjejkdmem
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar cat 314 d lcr excavator (prefix pdp) service repair manual (pdp00...fhsejkdkmem
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar cat 314 d lcr excavator (prefix pdp) service repair manual (pdp00...fhsjekkdkem
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar cat 314 d cr excavator (prefix pdp) service repair manual (pdp000...fjjsekdmme
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. Key steps include using specific tools to remove the idler gear, shaft, and bushing. Clearances and backlash must be checked and specifications met. The front housing is removed by taking out mounting bolts and requires checking gaskets and seals.
Caterpillar Cat 314D CR and 314D LCR Excavator (Prefix PDP) Service Repair Ma...fijsekkdmdm2w
The document provides instructions for removing and installing the idler gear and front housing on a Caterpillar 314D CR and 314D LCR excavator with a C4.2 engine. The removal procedure includes using various tools to remove the idler gear, idler shaft, and front housing. The installation procedure outlines installing the idler gear, checking gear backlash and end play, and installing the front housing.
Caterpillar Cat 314D CR and 314D LCR Excavator (Prefix PDP) Service Repair Ma...zan2736ban
The document provides instructions for removing and installing an idler gear on the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt and washer, thrust plate, and idler gear. It notes to check the idler shaft for wear and replace if needed. Instructions are also provided for installing the idler gear, including measuring backlash and end play.
Similar to Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl00001 and up) (14)
Bomag bw 154 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 154 ac 4 tandem rollers service repair manualfhjsjkdmemm
The document provides technical specifications and adjustment values for Tandem Rollers models BW 141 AD Serie 4 and BW 154 AD Serie 4. It includes details on the engine, travel pump, travel motors, drum reduction gear, vibration pump, vibration motor, steering and charge pump, and filling capacities. The specifications are broken out by component and include information like component type, system, displacement, pressure levels, speeds, ratios, and approved lubricants.
Bomag bw 151 ad 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The safety section emphasizes that the machine must only be used for its intended purposes of compacting asphalt and soil and stresses the importance of following all safety instructions.
Bomag bw 151 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 151 ac 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The safety section emphasizes that the machine must only be used for its intended purposes of compacting asphalt and soil and stresses the importance of following all safety instructions.
Bomag bw 141 ad 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The technical data section specifies the dimensions, weights, engine, and other technical specifications for each roller model.
Bomag bw 141 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 141 ac 4 tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD Serie 4, BW 154 AD Serie 4, and BW 154 AD AM Serie 4. It includes specifications for the Deutz diesel engine, travel pump and motors, vibration pump and motors, steering pump, and filling capacities. The data is presented in a table format with specifications such as engine power, pump displacement volumes, pressure settings, and fluid capacities.
Bomag bw 135 ad single tandem vibratory roller service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers. It includes technical specifications, safety regulations, descriptions of indicators and controls, operating instructions, maintenance instructions, and troubleshooting information. Safety is emphasized, including intended and prohibited uses of the machines, and potential hazards are outlined.
Hyundai r170 w 7a wheel excavator service repair manualfhjsjkdmemm
The document provides instructions for removing and installing a swing motor, disassembling and assembling the swing motor, removing and installing a reduction gear, and disassembling and assembling the reduction gear of an excavator. The summary is as follows:
1. The removal and installation instructions for the swing motor include disconnecting hoses and mounting bolts, and removing the swing motor assembly. Installation is the reverse of removal.
2. Disassembling the swing motor involves removing components like the valve, casing, piston, and shaft. Assembly is the reverse of disassembly.
3. Removal and installation of the reduction gear involves slinging and removing/installing mounting bolts.
Caterpillar cat 336 f excavator (prefix dsw) service repair manual (dsw00001 ...fhjsjkdmemm
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, friction plates, seals, springs, and other internal components. Detailed illustrations are provided to identify each part mentioned in the procedure. Safety precautions are noted throughout to warn of potential spring forces or fluid containment. The goal is to break down the travel motor into its core components while maintaining the correct orientation of parts for reassembly.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fhjsjkdmemm
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other internal components. Safety warnings are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fhjsjkdmemm
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix wdc) service repair manual (wdc000...fhjsjkdmemm
The document provides instructions for assembling a piston motor. It details 17 steps to install various parts like bearings, seals, springs, and retaining rings. Safety precautions are included to properly handle parts under spring tension. The assembly ends by installing the head and bolts.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...fhjsjkdmemm
The document provides instructions for removing and installing various engine components, including:
- Valve guides are removed from the cylinder head using a valve guide driver tool. New guides are installed using driver tools until the proper height is reached.
- Valve seat inserts are removed from the cylinder head using extractors. New inserts are installed using a driver tool after being cooled.
- The engine oil filter base, oil filter, and oil cooler are removed. Hoses are disconnected and bolts removed to access these components.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...fhjsjkdmemm
1. The document provides instructions for disassembling and assembling the piston pump of a 336D2 excavator.
2. The disassembly process involves removing 27 individual parts in a specific order, taking care with spring-loaded components.
3. Reassembly requires installing the parts in the reverse order, with some components requiring special tools or heating/cooling during installation. Proper end play must be verified during assembly.
Caterpillar cat 336 d2 l excavator (prefix ggh) service repair manual (ggh000...fhjsjkdmemm
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of an excavator model 336D2. The disassembly procedure involves removing 22 parts from the pump housing, including springs, seals, pistons, and bearings. The assembly procedure lists 30 steps to reinstall the parts in reverse order and adjust clearances using various tools. Precautions are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...fhjsjkdmemm
This document provides instructions for installing a final drive and travel motor on an excavator. It outlines 11 steps, including positioning the travel motor and final drive with lifting devices, installing O-rings and seals, connecting hoses and fittings, and tightening bolts to specified torques. Safety notices are provided to handle fluids properly and keep components clean from contaminants. Required tools include vacuum caps, link brackets, and anti-seize compound.
Caterpillar cat 336 d2 l excavator (prefix elr) service repair manual (elr000...fhjsjkdmemm
This document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the process is reversed - mounting bolts are installed and all connections reattached. Proper cleaning and use of new O-rings is emphasized to prevent contamination.
Caterpillar cat 336 d2 l excavator (prefix eft) service repair manual (eft000...fhjsjkdmemm
This document provides instructions for disassembling and assembling the travel motor on 336D2 and 336D2 L excavators. The disassembly process involves using various tools to remove components like retaining rings, seals, pistons, springs, and bearings. The assembly process describes installing these components in reverse order and notes that cleanliness is important, components should be lubricated, and parts must be installed in their proper positions and orientations.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01374810
Illustration 6 g01374811
5. The following items are components of Tooling (A).
◦ 9U-6147 Stud (9)
◦ 6V-8231 Nut (10)
◦ 9U-6146 Sleeve Assembly (11)
◦ 8T-4244 Nut (12)
6. Use Tooling (A) in order to remove idler shaft (8) (not shown) from the cylinder block.
Check idler shaft (8) for wear and damage. Replace idler shaft (8), if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
◦ In order to remove camshaft gear (3), refer to Disassembly and Assembly, "Camshaft
- Remove".
◦ In order to remove fuel injection pump gear (1), refer to Disassembly and Assembly,
"Fuel Injection Pump - Remove".
◦ In order to remove the gear from the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Remove".
◦ In order to remove crankshaft gear (4), refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:32:55 UTC+0800 2020
4/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879402
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
a 1p-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01374804
1. Use Tooling (A) and a suitable press in order to install a new bushing (7) (not shown), if the
bushing was removed.
Illustration 2 g01374810
2. Lower the temperature of idler shaft (8) . Install idler shaft (8) (not shown) onto the cylinder
block.
Note: When idler shaft (8) is installed, ensure that the oil hole of idler shaft (8) is up.
Illustration 3 g01374827
3. Install idler gear (2) onto idler shaft (8) .
2/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 4 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
Illustration 5 g01374789
4. Install thrust plate (6) onto the idler shaft.
5. Install the washer and idler gear bolt (5) onto thrust plate (6) . Tighten idler gear bolt (5) to a
torque of 34 ± 5 N·m (25 ± 4 lb ft).
3/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Note: See the following list for the installation of the other gears in the front gear group.
◦ In order to install the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Install".
◦ In order to install the fuel injection pump gear, refer to Disassembly and Assembly,
"Fuel Injection Pump - Install".
◦ In order to install the gear to the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Install".
◦ In order to install the crankshaft front gear, refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Illustration 6 g01374841
6. Install a dial indicator and rotate idler gear (2) back and forth in order to measure backlash.
Refer to Table 3.
Table 2
Item Standard at Assembly Service Limit
Backlash of crankshaft gear and
idler gear
0.510 to 0.157 mm (0.0201 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of camshaft gear and
idler gear
0.520 to 0.158 mm (0.0205 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of fuel injection pump
gear and idler gear
0.0560 to 0.205 mm (0.0022 to
0.0081 inch)
0.250 mm (0.0098
inch)
4/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. End play of idler gear
0.050 to 0.200 mm (0.0020 to
0.0079 inch)
0.350 mm (0.0138
inch)
Clearance between idler gear
bushing and shaft
0.009 to 0.050 mm (0.0004 to
0.0020 inch)
0.100 mm (0.0039
inch)
Illustration 7 g01374874
7. Measure the end play of idler gear (2) with a feeler gauge. Refer to Table 3.
End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:33:54 UTC+0800 2020
5/5
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02743335
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
a. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
b. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
c. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
d. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374908
1. Loosen hose clamp (1) that secures hose (2) to the front housing.
2. Disconnect hose (2) from the front housing.
Illustration 2 g00605985
3. Remove bolts (3) and the washers that hold front housing (4) to the plate and the cylinder
block.
2/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 4. Remove six bolts (5) (not shown) and the washers that mount front housing (4) to the oil
pan.
Illustration 3 g00606002
5. Remove bolts (6) and the washers that mount front housing (4) to front plate (8) and the
cylinder block.
6. Use two people in order to remove front housing (4) from the cylinder block and front plate
(8). The weight of front housing (4) is approximately 20 kg (45 lb).
Note: Check the condition of gasket (7) (not shown) for the engine oil pan. If gasket (7) is
damaged, it may be necessary to replace gasket (7). Refer to Disassembly and Assembly,
"Engine Oil Pan - Remove and Install" for replacement of gasket (7) for the engine oil pan.
3/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g01377884
7. Remove baffle plate (9).
Illustration 5 g01377894
8. Use Tooling (A) in order to remove crankshaft front seal (10) (not shown) from front
housing (4), if necessary.
9. Check the teeth of the timing gears for the following items: wear, nicks, chips and uneven
contact. Check the keyway for wear or damage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:34:53 UTC+0800 2020
4/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879387
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets, and the seals for wear or for damage. Replace the components, if
necessary.
1/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00836619
Alignment marks for timing gears
1. Check the alignment of the timing gears.
Note: Ensure that the marks on the timing gears are in alignment. Align the "3" mark on the
fuel injection pump drive gear with the "33" mark on the idler gear. Make an alignment of
the "2" mark on the idler gear with the "22" mark on the camshaft gear. Align the "1" mark
on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top
center position when the timing marks are in alignment.
Illustration 2 g00606022
2. Ensure that the old gasket material (9) is removed from the mating surface of front housing
(4) and the timing gear plate. Install a new gasket (9) .
3. If the crankshaft front seal (10) (not shown) was removed, use Tooling (A) in order to
install a new crankshaft front seal (10) .
2/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00606002
4. Before installation of front housing (4) , check gasket (7) (not shown) for the oil pan for
damage. Replace gasket (7) , if necessary. Refer to Disassembly and Assembly, "Engine Oil
Pan - Remove and Install" for replacement of gasket (7) for the engine oil pan.
5. Use two people in order to install front housing (4) onto front plate (8) and the cylinder
block. The weight of front housing (4) is approximately 20 kg (45 lb).
6. Install bolts (6) in order to fasten front housing (4) onto the cylinder block and front plate
(8) .
Illustration 4 g00605985
7. Install the washers and six bolts (5) (not shown) in order to secure front housing (4) onto
engine oil pan.
3/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 8. Install bolts (3) and washers that secure front housing (4) to the front plate and the cylinder
block.
Illustration 5 g01374908
9. Connect hose (2) to the front housing.
10. Tighten hose clamp (1) in order to secure hose (2) to the front housing.
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
c. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
d. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:35:52 UTC+0800 2020
4/4
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i01615486
Front Plate - Remove
SMCS - 1163-011
Removal Procedure
Start By:
a. Remove the idler gear. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove".
b. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
c. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00611711
1. Remove one bolt (1) and the washer from the front plate (2).
2. Remove front plate (2) from the engine.
3. Remove gasket (3) (not shown) from the engine or from the front plate (2).
Note: Ensure that all mating surfaces are clear of old gaskets.
Note: Check the cylinder block for the following conditions: scale buildup, corrosion and
other damage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:36:52 UTC+0800 2020
2/2
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i01576831
Front Plate - Install
SMCS - 1163-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611711
1. Place gasket (3) (not shown) in position on the engine.
Note: Ensure that all mating surfaces are clear of old gaskets.
2. Place front plate (2) in position on the engine.
1/2
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 3. Install one bolt (1) and the washer in order to secure front plate (2) to the engine. Tighten
the bolt to a torque of 35 ± 5 N·m (26 ± 4 lb ft).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
c. Install the idler gear. Refer to Disassembly and Assembly, "Gear Group (Front) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:37:51 UTC+0800 2020
2/2
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879389
Crankcase Breather - Remove and Install
SMCS - 1317-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g01374569
1. Loosen clamps (3) and remove hose (2) .
2. Remove breather assembly (1) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01374569
1. Install new breather assembly (1) .
2. Install hose (2) and tighten hose clamps (3) .
Wed May 27 08:38:50 UTC+0800 2020
2/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312D EXCAVATOR RHL
Configuration: 312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768517
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01384853
1. Remove bolts (1) and remove cover (2) .
1/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 2 g01385013
2. Disconnect hose (3) .
3. Remove bolts (4) and remove valve mechanism cover (5) and the O-ring seal.
Installation Procedure
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01385013
1. Position valve mechanism cover (5) and the O-ring seal. Install bolts (4). Tighten bolts (4)
to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
2/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 2. Connect hose (3) .
Illustration 4 g01384853
3. Position cover (2) and install bolts (1). Tighten bolts (1) to a torque of 17 ± 2 N·m (13 ± 1 lb
ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 27 08:39:50 UTC+0800 2020
3/3
312D & 312D L Excavators RHL00001-UP (MACHINE) POWERED BY C4.2 Engin...
2020/5/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...