This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear, shaft, thrust plate and washer. The installation procedure specifies cleaning parts and using a press and driver group to re-install these components, checking backlash and end play tolerances. Proper alignment of timing gear marks is also emphasized.
Caterpillar cat 323 d l excavator (prefix pbe) service repair manual (pbe0000...fjjsekmsmmes
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to re-install components in reverse order, checking backlash and end play tolerances.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...shudun96087
This document provides instructions for removing and installing the idler gear on the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear. The installation procedure specifies cleaning parts and aligning timing gear marks before installing the idler gear, thrust plate, and idler gear bolt. Tolerances for backlash and clearances are provided to check proper installation.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...qme229722
This document provides instructions for removing and installing the idler gear on the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear. The installation procedure specifies cleaning parts and aligning timing gear marks before installing the idler gear, thrust plate, and idler gear bolt. Tolerances for backlash and clearances are provided to check proper installation.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...kesi7153062
This document provides instructions for removing and installing the idler gear on the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear. The installation procedure specifies cleaning parts and aligning timing gear marks before installing the idler gear, thrust plate, and idler gear bolt. Tolerances for backlash and clearance measurements are provided to check proper installation.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on the shaft.
3) Checking gear backlash and end play measurements during installation.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...zan2736ban
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt, thrust plate, and idler gear using various tools. Clearances and backlash measurements are specified when installing the idler gear. Removing additional gears like the camshaft and crankshaft gears are also referenced. Proper containment of fluids and cleaning of parts are emphasized.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...fusjekkdmdmd2w
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines reinstalling these components and checking gear backlash and end play tolerances. Additional instructions are provided for removing and installing the front housing of the engine.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar cat 323 d l excavator (prefix pbe) service repair manual (pbe0000...fjjsekmsmmes
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to re-install components in reverse order, checking backlash and end play tolerances.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...shudun96087
This document provides instructions for removing and installing the idler gear on the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear. The installation procedure specifies cleaning parts and aligning timing gear marks before installing the idler gear, thrust plate, and idler gear bolt. Tolerances for backlash and clearances are provided to check proper installation.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...qme229722
This document provides instructions for removing and installing the idler gear on the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear. The installation procedure specifies cleaning parts and aligning timing gear marks before installing the idler gear, thrust plate, and idler gear bolt. Tolerances for backlash and clearances are provided to check proper installation.
Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual (PBE00001...kesi7153062
This document provides instructions for removing and installing the idler gear on the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear. The installation procedure specifies cleaning parts and aligning timing gear marks before installing the idler gear, thrust plate, and idler gear bolt. Tolerances for backlash and clearance measurements are provided to check proper installation.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on the shaft.
3) Checking gear backlash and end play measurements during installation.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...zan2736ban
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt, thrust plate, and idler gear using various tools. Clearances and backlash measurements are specified when installing the idler gear. Removing additional gears like the camshaft and crankshaft gears are also referenced. Proper containment of fluids and cleaning of parts are emphasized.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...fusjekkdmdmd2w
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, and idler gear from the idler gear shaft. The installation procedure outlines reinstalling these components and checking gear backlash and end play tolerances. Additional instructions are provided for removing and installing the front housing of the engine.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on in reverse order of removal.
3) Checking gear backlash and end play measurements against specifications.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...f8usejkddmmd
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and installing the gear, thrust plate, washer and bolt.
3) Checking gear backlash and end play measurements during installation.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...ikdkdmddm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to install the bushing and idler shaft, then aligning the timing gears and checking backlash clearances.
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on in reverse order of removal.
3) Checking gear backlash and end play measurements against specifications.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...8ufjsekddm8u
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt, thrust plate, and idler gear using various tools. Clearances and backlash measurements are specified when installing the idler gear. Removing additional gears like the camshaft and crankshaft gears are also referenced. Proper containment of fluids and cleaning of parts are emphasized.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...ikdkdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...ufjksemd8ujd
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt, thrust plate, and idler gear using various tools. Clearances and backlash measurements are specified when installing the idler gear. Removing additional gears like the camshaft and crankshaft gears are also referenced. Proper containment of fluids and cleaning of parts are emphasized.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...km7seydwuhdw
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to install the bushing and idler shaft, and aligning timing gear marks when reinstalling the idler gear. Tolerances for backlash and clearances are provided.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...jdkskmdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using tools to install the bushing, idler shaft, idler gear, thrust plate, washer, and idler gear bolt while ensuring proper gear alignment and backlash. Tolerances for backlash and clearances are provided.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to install the bushing and idler shaft, and aligning timing gear marks when reinstalling the idler gear. Tolerances for backlash and clearances are provided.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...prmy389342
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear, idler shaft, thrust plate and washer. The installation procedure specifies cleaning parts and ensuring proper alignment of timing gear marks before pressing in a new bushing if needed, installing the idler shaft, gear, thrust plate and bolt. Tolerances for backlash and end play are provided to check installation.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fhjsjkdmemm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Installation involves reversing the removal steps and ensuring proper gear alignment and specifications are met. Additional documents are referenced for removing other gears in the front group.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...cdfzxs
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on in reverse order of removal.
3) Checking gear backlash and end play measurements against specifications.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fjjskmdmem
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Checks are made for wear on removed parts. The installation procedure specifies cleaning parts and aligning timing gear marks before pressing in a new bushing if needed, installing the idler shaft and gear, and torquing the idler gear bolt. Clearances and backlash are checked against specifications.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...dueikdkmem
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Installation involves reversing the removal steps and ensuring proper gear alignment and specifications are met. Additional documents are referenced for removing other gears in the front group.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
More Related Content
Similar to Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual Instant Download.pdf
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on in reverse order of removal.
3) Checking gear backlash and end play measurements against specifications.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...f8usejkddmmd
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and installing the gear, thrust plate, washer and bolt.
3) Checking gear backlash and end play measurements during installation.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...ikdkdmddm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to install the bushing and idler shaft, then aligning the timing gears and checking backlash clearances.
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on in reverse order of removal.
3) Checking gear backlash and end play measurements against specifications.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...8ufjsekddm8u
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt, thrust plate, and idler gear using various tools. Clearances and backlash measurements are specified when installing the idler gear. Removing additional gears like the camshaft and crankshaft gears are also referenced. Proper containment of fluids and cleaning of parts are emphasized.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...ikdkdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...ufjksemd8ujd
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
The document provides instructions for removing and installing an idler gear in the front gear group of a Caterpillar C4.2 engine. It describes removing the front housing, idler gear bolt, thrust plate, and idler gear using various tools. Clearances and backlash measurements are specified when installing the idler gear. Removing additional gears like the camshaft and crankshaft gears are also referenced. Proper containment of fluids and cleaning of parts are emphasized.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...km7seydwuhdw
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to install the bushing and idler shaft, and aligning timing gear marks when reinstalling the idler gear. Tolerances for backlash and clearances are provided.
Caterpillar Cat 312D and 312D L Excavator (Prefix RHL) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...jdkskmdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using tools to install the bushing, idler shaft, idler gear, thrust plate, washer, and idler gear bolt while ensuring proper gear alignment and backlash. Tolerances for backlash and clearances are provided.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to install the bushing and idler shaft, and aligning timing gear marks when reinstalling the idler gear. Tolerances for backlash and clearances are provided.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...prmy389342
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear, idler shaft, thrust plate and washer. The installation procedure specifies cleaning parts and ensuring proper alignment of timing gear marks before pressing in a new bushing if needed, installing the idler shaft, gear, thrust plate and bolt. Tolerances for backlash and end play are provided to check installation.
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using a press and tools to reinstall components in reverse order, checking gear backlash and end play tolerances.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fhjsjkdmemm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Installation involves reversing the removal steps and ensuring proper gear alignment and specifications are met. Additional documents are referenced for removing other gears in the front group.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...cdfzxs
The document provides instructions for removing and installing an idler gear on a Caterpillar C4.2 engine. It describes:
1) Removing the idler gear by removing the bolt and washer, thrust plate, and pulling the gear off using a puller tool.
2) Installing the idler gear by pressing in a new bushing if needed, lowering the idler shaft temperature, and placing the gear, thrust plate and bolt back on in reverse order of removal.
3) Checking gear backlash and end play measurements against specifications.
Caterpillar cat 312 d l excavator (prefix rhl) service repair manual (rhl0000...fjjskmdmem
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Checks are made for wear on removed parts. The installation procedure specifies cleaning parts and aligning timing gear marks before pressing in a new bushing if needed, installing the idler shaft and gear, and torquing the idler gear bolt. Clearances and backlash are checked against specifications.
Caterpillar cat 312 d excavator (prefix rhl) service repair manual (rhl00001 ...dueikdkmem
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. Installation involves reversing the removal steps and ensuring proper gear alignment and specifications are met. Additional documents are referenced for removing other gears in the front group.
Similar to Caterpillar Cat 323D L Excavator (Prefix PBE) Service Repair Manual Instant Download.pdf (20)
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing the idler gear of the front gear group on a C4.2 engine for Caterpillar built machines.
- To remove the idler gear, the front housing must first be removed. Then the idler gear bolt, thrust plate, and idler gear can be taken off the idler gear shaft. An idler shaft puller and driver group may be needed.
- To install the idler gear, first press in a new bushing if needed. Then install the idler shaft, idler gear, thrust plate, washer and idler gear bolt. Tighten the bolt to the specified torque.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
Caterpillar Cat 336F and 336F L Excavator (Prefix DSW) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs and seals. Tools required include a transmission repair stand, lifting eye assembly, driver group and various bolts, pins and seals. Technicians are advised to mark components for reinstallation and take care when removing parts to avoid damage.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 345D L Excavator (Prefix JKN) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, bearings and other components into the travel motor housing and barrel. Measurements are taken throughout to ensure proper assembly. The travel motor is then installed on the excavator and filled with the correct oil type.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive, which include removing the cover, gears, and planetary gear assembly. Personal injury warnings are provided and all components must be cleaned before assembly.
Caterpillar Cat 336E L Excavator (Prefix BZY) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstalling parts. Special care must be taken when handling springs or parts under spring force to avoid injury.
Caterpillar Cat 330F and 330F L Excavator (Prefix LCG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. It describes 37 steps to disassemble the final drive by removing gears, shafts, housings, seals and other components. It then describes 34 steps to reassemble the final drive, including pressing in new bearings, installing seals, adjusting bearing preload with shims, and applying threadlocker to bolts. Precise tools and lifting devices are required due to the heavy weights of up to 550 kg involved.
Caterpillar Cat 336E L Excavator (Prefix DPX) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor on a 336E L excavator. The disassembly process involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on lubricating parts and ensuring proper alignment of components.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fskekkdmdmdm3e
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It describes removing over 30 components of the travel motor including the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates and more.
3) Detailed illustrations are provided to accompany each step showing how to remove each component using the recommended tools.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, in reverse order, including attaching lifting devices, positioning the assembly, and reinstalling hoses and covers. Tools and torque specifications are provided.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLC) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for removing and installing a crankshaft wear sleeve and crankshaft gear on a 325C excavator. It describes using various tools to distort and remove the existing wear sleeve and instructions for installing a new sleeve using a multi-piece installer tool. It also outlines steps for removing the crankshaft gear using a bearing puller and installing the gear by heating it and pressing it onto the crankshaft. The document provides maintenance technicians with detailed parts and tool information as well as safety notices for completing these tasks.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal of a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 12 steps including cleaning parts, installing bearings, seals, gears, and bolts while ensuring proper dimensions and torque specifications are followed. Tools required include drivers, link brackets, guide studs, and installation tools.
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306B engine. It describes:
1) Marking the gears to ensure proper timing during removal and installation.
2) Removing the camshaft bolts and carefully removing the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before installation.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
The document provides instructions for removing and installing various components of a Caterpillar 621E wheel scraper, including:
1) Removing and installing the push-pull plate that connects the push-pull spring to the support assembly.
2) Disassembling and assembling the push-pull spring itself by removing discs and plates.
3) A detailed process for removing and installing the ejector cylinder, which requires the use of lifting tools and wood blocks due to the cylinder's weight.
4) Brief instructions for removing and adjusting the position of the lower front and guide rollers on the ejector assembly.
This document provides assembly instructions for a final drive on an excavator. It involves assembling and installing several components in the following order: installing bearings and determining shim thickness; installing seals; installing dowel pins; installing the housing on the motor housing; installing coupling gear, bolts, and ring gear; assembling carrier assemblies; installing gears, shafts, and retaining rings; installing the cover and testing for leaks. The process requires precision measurements and uses several specialized tools to properly assemble the final drive.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01374810
Illustration 6 g01374811
5. The following items are components of Tooling (A).
◦ 9U-6147 Stud (9)
◦ 6V-8231 Nut (10)
◦ 9U-6146 Sleeve Assembly (11)
◦ 8T-4244 Nut (12)
6. Use Tooling (A) in order to remove idler shaft (8) (not shown) from the cylinder block.
Check idler shaft (8) for wear and damage. Replace idler shaft (8), if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
◦ In order to remove camshaft gear (3), refer to Disassembly and Assembly, "Camshaft
- Remove".
◦ In order to remove fuel injection pump gear (1), refer to Disassembly and Assembly,
"Fuel Injection Pump - Remove".
◦ In order to remove the gear from the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Remove".
◦ In order to remove crankshaft gear (4), refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 16:54:48 UTC+0800 2020
4/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02879402
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
a 1p-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01374804
1. Use Tooling (A) and a suitable press in order to install a new bushing (7) (not shown), if the
bushing was removed.
Illustration 2 g01374810
2. Lower the temperature of idler shaft (8) . Install idler shaft (8) (not shown) onto the cylinder
block.
Note: When idler shaft (8) is installed, ensure that the oil hole of idler shaft (8) is up.
Illustration 3 g01374827
3. Install idler gear (2) onto idler shaft (8) .
2/5
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 4 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
Illustration 5 g01374789
4. Install thrust plate (6) onto the idler shaft.
5. Install the washer and idler gear bolt (5) onto thrust plate (6) . Tighten idler gear bolt (5) to a
torque of 34 ± 5 N·m (25 ± 4 lb ft).
3/5
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Note: See the following list for the installation of the other gears in the front gear group.
◦ In order to install the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Install".
◦ In order to install the fuel injection pump gear, refer to Disassembly and Assembly,
"Fuel Injection Pump - Install".
◦ In order to install the gear to the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Install".
◦ In order to install the crankshaft front gear, refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Illustration 6 g01374841
6. Install a dial indicator and rotate idler gear (2) back and forth in order to measure backlash.
Refer to Table 3.
Table 2
Item Standard at Assembly Service Limit
Backlash of crankshaft gear and
idler gear
0.510 to 0.157 mm (0.0201 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of camshaft gear and
idler gear
0.520 to 0.158 mm (0.0205 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of fuel injection pump
gear and idler gear
0.0560 to 0.205 mm (0.0022 to
0.0081 inch)
0.250 mm (0.0098
inch)
4/5
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. End play of idler gear
0.050 to 0.200 mm (0.0020 to
0.0079 inch)
0.350 mm (0.0138
inch)
Clearance between idler gear
bushing and shaft
0.009 to 0.050 mm (0.0004 to
0.0020 inch)
0.100 mm (0.0039
inch)
Illustration 7 g01374874
7. Measure the end play of idler gear (2) with a feeler gauge. Refer to Table 3.
End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 16:55:47 UTC+0800 2020
5/5
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02743335
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
a. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
b. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
c. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
d. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374908
1. Loosen hose clamp (1) that secures hose (2) to the front housing.
2. Disconnect hose (2) from the front housing.
Illustration 2 g00605985
3. Remove bolts (3) and the washers that hold front housing (4) to the plate and the cylinder
block.
2/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 4. Remove six bolts (5) (not shown) and the washers that mount front housing (4) to the oil
pan.
Illustration 3 g00606002
5. Remove bolts (6) and the washers that mount front housing (4) to front plate (8) and the
cylinder block.
6. Use two people in order to remove front housing (4) from the cylinder block and front plate
(8). The weight of front housing (4) is approximately 20 kg (45 lb).
Note: Check the condition of gasket (7) (not shown) for the engine oil pan. If gasket (7) is
damaged, it may be necessary to replace gasket (7). Refer to Disassembly and Assembly,
"Engine Oil Pan - Remove and Install" for replacement of gasket (7) for the engine oil pan.
3/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g01377884
7. Remove baffle plate (9).
Illustration 5 g01377894
8. Use Tooling (A) in order to remove crankshaft front seal (10) (not shown) from front
housing (4), if necessary.
9. Check the teeth of the timing gears for the following items: wear, nicks, chips and uneven
contact. Check the keyway for wear or damage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 16:56:47 UTC+0800 2020
4/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02879387
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets, and the seals for wear or for damage. Replace the components, if
necessary.
1/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00836619
Alignment marks for timing gears
1. Check the alignment of the timing gears.
Note: Ensure that the marks on the timing gears are in alignment. Align the "3" mark on the
fuel injection pump drive gear with the "33" mark on the idler gear. Make an alignment of
the "2" mark on the idler gear with the "22" mark on the camshaft gear. Align the "1" mark
on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top
center position when the timing marks are in alignment.
Illustration 2 g00606022
2. Ensure that the old gasket material (9) is removed from the mating surface of front housing
(4) and the timing gear plate. Install a new gasket (9) .
3. If the crankshaft front seal (10) (not shown) was removed, use Tooling (A) in order to
install a new crankshaft front seal (10) .
2/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00606002
4. Before installation of front housing (4) , check gasket (7) (not shown) for the oil pan for
damage. Replace gasket (7) , if necessary. Refer to Disassembly and Assembly, "Engine Oil
Pan - Remove and Install" for replacement of gasket (7) for the engine oil pan.
5. Use two people in order to install front housing (4) onto front plate (8) and the cylinder
block. The weight of front housing (4) is approximately 20 kg (45 lb).
6. Install bolts (6) in order to fasten front housing (4) onto the cylinder block and front plate
(8) .
Illustration 4 g00605985
7. Install the washers and six bolts (5) (not shown) in order to secure front housing (4) onto
engine oil pan.
3/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 8. Install bolts (3) and washers that secure front housing (4) to the front plate and the cylinder
block.
Illustration 5 g01374908
9. Connect hose (2) to the front housing.
10. Tighten hose clamp (1) in order to secure hose (2) to the front housing.
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
c. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
d. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 16:57:46 UTC+0800 2020
4/4
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01615486
Front Plate - Remove
SMCS - 1163-011
Removal Procedure
Start By:
a. Remove the idler gear. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove".
b. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
c. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00611711
1. Remove one bolt (1) and the washer from the front plate (2).
2. Remove front plate (2) from the engine.
3. Remove gasket (3) (not shown) from the engine or from the front plate (2).
Note: Ensure that all mating surfaces are clear of old gaskets.
Note: Check the cylinder block for the following conditions: scale buildup, corrosion and
other damage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 16:58:45 UTC+0800 2020
2/2
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01576831
Front Plate - Install
SMCS - 1163-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00611711
1. Place gasket (3) (not shown) in position on the engine.
Note: Ensure that all mating surfaces are clear of old gaskets.
2. Place front plate (2) in position on the engine.
1/2
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 3. Install one bolt (1) and the washer in order to secure front plate (2) to the engine. Tighten
the bolt to a torque of 35 ± 5 N·m (26 ± 4 lb ft).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
c. Install the idler gear. Refer to Disassembly and Assembly, "Gear Group (Front) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 16:59:44 UTC+0800 2020
2/2
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02879389
Crankcase Breather - Remove and Install
SMCS - 1317-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g01374569
1. Loosen clamps (3) and remove hose (2) .
2. Remove breather assembly (1) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01374569
1. Install new breather assembly (1) .
2. Install hose (2) and tighten hose clamps (3) .
Sun Aug 30 17:00:44 UTC+0800 2020
2/3
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR PBE
Configuration: 323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742668
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01374565
1/2
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. 1. Loosen clamp (2) and disconnect hose (1).
2. Remove bolts (4) and remove valve mechanism cover (3) and the O-ring seal.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01374565
1. Position valve mechanism cover (3) and the O-ring seal. Install bolts (4). Tighten bolts (4)
to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
2. Connect hose (1) and tighten clamp (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 30 17:01:43 UTC+0800 2020
2/2
323D L Excavator PBE00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP53...
2020/8/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...