This document provides instructions for removing and installing an inlet manifold and inlet and exhaust valves on a Caterpillar 314D LCR excavator. It describes the required tools, removal process which involves removing mounting bolts and clips, and installation process which involves installing gaskets, bolts, clips and ensuring proper torque specifications. Safety notices are provided regarding keeping parts clean, wearing protective equipment and avoiding damage to components.
Caterpillar cat 314 d lcr excavator (prefix txn) service repair manual (txn00...ifosodkmsme
This document provides instructions for removing and installing the inlet manifold, inlet and exhaust valves, and inlet and exhaust valve springs on a Caterpillar C4.2 engine. The removal process involves using various tools to compress springs and rotate the crankshaft to access components. Installation involves cleaning parts, applying new seals, and carefully reassembling components in the reverse order of removal. Precautions are listed to prevent damage and entry of loose parts into the engine.
Caterpillar cat 314 d lcr excavator (prefix txn) service repair manual (txn00...fjskekdmjekm
The document provides instructions for removing and installing the inlet manifold and inlet and exhaust valves on a Caterpillar 314D LCR excavator. The procedures include using various tools to compress springs, remove bolts and clips, and correctly position gaskets and other components. Precautions are outlined to prevent damage and ensure parts are clean prior to installation. Diagrams illustrate the components and steps in the processes.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...jjskefkskemik
1. The document provides removal and installation instructions for the inlet manifold on a Caterpillar C6.4 engine.
2. Key steps include using tools to remove bolts and clips, disconnecting hoses, and lifting the manifold off using a bracket and lifting device.
3. Installation involves positioning a new gasket, bolting the manifold back into place, reconnecting hoses, and tightening to the specified torques.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...fujsjfkskemm
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...udfdesd
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened, and clips are reinstalled. Safety notices are provided to keep parts clean and securely lift the manifold due to its weight.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...ufdjjsekkmdme
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...fujsjfkkskefsme
1. The document provides removal and installation instructions for an inlet manifold on a Caterpillar 321D LCR excavator. It details using various tools to remove bolts and clips, disconnect hoses, and lift the manifold off the engine.
2. Removal and installation procedures are also given for inlet and exhaust valve springs on the excavator's C6.4 engine. Tools are used to compress springs and rotate the crankshaft to access the valves.
3. Finally, instructions are provided to remove and install inlet and exhaust valves, using tools like a cylinder head repair stand and valve spring compressor. Precautions are emphasized to avoid damage and properly release spring pressure.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 314 d lcr excavator (prefix txn) service repair manual (txn00...ifosodkmsme
This document provides instructions for removing and installing the inlet manifold, inlet and exhaust valves, and inlet and exhaust valve springs on a Caterpillar C4.2 engine. The removal process involves using various tools to compress springs and rotate the crankshaft to access components. Installation involves cleaning parts, applying new seals, and carefully reassembling components in the reverse order of removal. Precautions are listed to prevent damage and entry of loose parts into the engine.
Caterpillar cat 314 d lcr excavator (prefix txn) service repair manual (txn00...fjskekdmjekm
The document provides instructions for removing and installing the inlet manifold and inlet and exhaust valves on a Caterpillar 314D LCR excavator. The procedures include using various tools to compress springs, remove bolts and clips, and correctly position gaskets and other components. Precautions are outlined to prevent damage and ensure parts are clean prior to installation. Diagrams illustrate the components and steps in the processes.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...jjskefkskemik
1. The document provides removal and installation instructions for the inlet manifold on a Caterpillar C6.4 engine.
2. Key steps include using tools to remove bolts and clips, disconnecting hoses, and lifting the manifold off using a bracket and lifting device.
3. Installation involves positioning a new gasket, bolting the manifold back into place, reconnecting hoses, and tightening to the specified torques.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...fujsjfkskemm
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...udfdesd
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened, and clips are reinstalled. Safety notices are provided to keep parts clean and securely lift the manifold due to its weight.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...ufdjjsekkmdme
This document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR excavator with a C6.4 engine. The removal process involves detaching hoses, removing bolts and clips, and lifting the manifold off using a lifting device. For installation, the gasket and hoses are reattached, bolts are tightened to the specified torques, and the fuel manifold is reinstalled at the end. Separate sections provide similar instructions for removing and installing inlet and exhaust valves, and related components like valve springs. Safety notices are included throughout regarding keeping parts clean and ensuring components are properly secured.
Caterpillar cat 321 d lcr excavator (prefix nas) service repair manual (nas00...fujsjfkkskefsme
1. The document provides removal and installation instructions for an inlet manifold on a Caterpillar 321D LCR excavator. It details using various tools to remove bolts and clips, disconnect hoses, and lift the manifold off the engine.
2. Removal and installation procedures are also given for inlet and exhaust valve springs on the excavator's C6.4 engine. Tools are used to compress springs and rotate the crankshaft to access the valves.
3. Finally, instructions are provided to remove and install inlet and exhaust valves, using tools like a cylinder head repair stand and valve spring compressor. Precautions are emphasized to avoid damage and properly release spring pressure.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjskekmsemm
This document provides the procedure for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and inspect for wear. Valves, guides, seals and other components are then reinstalled in the reverse order, taking care to lubricate parts and set components to the correct specifications.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
1. The document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR EXCAVATOR powered by a C6.4 engine.
2. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket.
3. The installation procedure specifies cleaning and preparing surfaces, positioning a new gasket, attaching hoses and bolts, and torquing bolts to the specified values.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...dkdmidkkdk
This document provides instructions for removing and installing inlet and exhaust valves and valve guides on a C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and lubricate components before installation. Precautions are outlined to prevent injury and ensure proper assembly.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing valves, valve guides, and the engine oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing valves, valve guides, and installing new components. The document also describes draining coolant and removing bolts to take off the engine oil cooler.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...uufjdjdkkksmem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the springs and remove the valve keepers and springs. When installing new springs, the document specifies installing them with the smaller pitch end downward. Safety precautions are provided to avoid injury from parts propelled by spring force.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...fjsjefskekfmme
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the springs and remove the valve keepers and springs. When installing new springs, the document specifies installing them with the smaller pitch end downward. Safety precautions are provided to avoid injury from parts propelled by spring force.
The document provides instructions for disassembling a swing drive from a 320C excavator. It describes:
1) Removing the retaining ring from the swing drive housing using retaining ring pliers.
2) Using a driver group to remove the bearing from the housing.
3) Removing the inner ring, roller assembly, and outer ring from the bearing.
The summary highlights the key steps in the disassembly process without providing all the detail from the original document. It focuses on the essential information needed to understand the high level disassembly procedure.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine, including:
- Removing and installing the fuel filter base
- Removing and installing the fuel injection lines
- Removing the fuel injection nozzles
- Installing new fuel injection nozzles
The summaries provide the high-level steps for each procedure in 3 sentences or less.
The document provides instructions for installing and assembling auxiliary control valves F1, F2, and F4 on a 320C excavator. It describes:
1) Installing the F1 and F4 control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Assembling the F2 control valve by installing O-rings, springs, and other components in the specified order and attaching fittings and plugs.
3) Completing installation by connecting hoses and electrical connectors, installing panels and covers, and filling the hydraulic system.
The document provides instructions for removing and installing various engine components on Caterpillar 320 and 320L track excavators, including:
1) Removing and installing the turbocharger, exhaust manifold, air inlet heater, and inlet manifold. The procedures describe removing bolts, nuts, hoses and other parts and replacing gaskets.
2) Keeping all parts clean to prevent contamination, which can cause rapid wear and shortened component life.
3) Tightening bolts and nuts to the specified torques once components are installed.
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...udza7545918
This document provides instructions for removing and installing components of the fuel transfer pump and governor for Caterpillar 320 excavators. The removal and installation procedures are described in detail over multiple pages with illustrations and required tools listed. Safety and contamination prevention notes are also provided throughout.
Caterpillar Cat 320 N EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...udza7545918
This document provides instructions for removing and installing components of the fuel transfer pump and governor for Caterpillar 320 excavators. The removal and installation procedures are described in detail over multiple pages with illustrations and required tools listed. Safety and contamination prevention notes are also provided throughout.
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...udza7545918
This document provides instructions for removing and installing a fuel transfer pump and governor on Caterpillar 320, 320L, 320N, and 320S excavators powered by a 3116 engine. The removal procedure involves removing covers, seals, springs, fittings and other components of the fuel transfer pump. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order. Similarly, removing the governor requires disconnecting lines and cables before removing mounting bolts, while installation is the reverse of removal.
This document provides instructions for removing and installing components of the fuel transfer pump and governor for Caterpillar 320 excavators. The removal and installation procedures are described in detail over multiple pages with illustrations and required tools listed. Safety and contamination prevention notes are also provided throughout.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and housing bolts. Instructions are given to lift the housing off the engine block using a link bracket and driver group. Reinstallation involves reversing the removal process and tightening the housing bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations are provided for removing the flywheel housing, crankshaft pulley, crankshaft front seal, and other components. Precautions are outlined for cleanliness and fluid containment.
More Related Content
Similar to Caterpillar Cat 314D LCR Excavator (Prefix TXN) Service Repair Manual (TXN00001 and up).pdf
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjskekmsemm
This document provides the procedure for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and inspect for wear. Valves, guides, seals and other components are then reinstalled in the reverse order, taking care to lubricate parts and set components to the correct specifications.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
1. The document provides instructions for removing and installing the inlet manifold on a Caterpillar 321D LCR EXCAVATOR powered by a C6.4 engine.
2. The removal procedure involves detaching hoses, removing bolts and clips, and lifting the manifold off using a link bracket.
3. The installation procedure specifies cleaning and preparing surfaces, positioning a new gasket, attaching hoses and bolts, and torquing bolts to the specified values.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...dkdmidkkdk
This document provides instructions for removing and installing inlet and exhaust valves and valve guides on a C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and lubricate components before installation. Precautions are outlined to prevent injury and ensure proper assembly.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing valves, valve guides, and the engine oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing valves, valve guides, and installing new components. The document also describes draining coolant and removing bolts to take off the engine oil cooler.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...uufjdjdkkksmem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the springs and remove the valve keepers and springs. When installing new springs, the document specifies installing them with the smaller pitch end downward. Safety precautions are provided to avoid injury from parts propelled by spring force.
Caterpillar cat 236 d skid steer loader (prefix mpw) service repair manual (m...fjsjefskekfmme
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar 236D Skid Steer Loader. It describes using a valve spring compressor tool to compress the springs and remove the valve keepers and springs. When installing new springs, the document specifies installing them with the smaller pitch end downward. Safety precautions are provided to avoid injury from parts propelled by spring force.
Similar to Caterpillar Cat 314D LCR Excavator (Prefix TXN) Service Repair Manual (TXN00001 and up).pdf (11)
The document provides instructions for disassembling a swing drive from a 320C excavator. It describes:
1) Removing the retaining ring from the swing drive housing using retaining ring pliers.
2) Using a driver group to remove the bearing from the housing.
3) Removing the inner ring, roller assembly, and outer ring from the bearing.
The summary highlights the key steps in the disassembly process without providing all the detail from the original document. It focuses on the essential information needed to understand the high level disassembly procedure.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine, including:
- Removing and installing the fuel filter base
- Removing and installing the fuel injection lines
- Removing the fuel injection nozzles
- Installing new fuel injection nozzles
The summaries provide the high-level steps for each procedure in 3 sentences or less.
The document provides instructions for installing and assembling auxiliary control valves F1, F2, and F4 on a 320C excavator. It describes:
1) Installing the F1 and F4 control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Assembling the F2 control valve by installing O-rings, springs, and other components in the specified order and attaching fittings and plugs.
3) Completing installation by connecting hoses and electrical connectors, installing panels and covers, and filling the hydraulic system.
The document provides instructions for removing and installing various engine components on Caterpillar 320 and 320L track excavators, including:
1) Removing and installing the turbocharger, exhaust manifold, air inlet heater, and inlet manifold. The procedures describe removing bolts, nuts, hoses and other parts and replacing gaskets.
2) Keeping all parts clean to prevent contamination, which can cause rapid wear and shortened component life.
3) Tightening bolts and nuts to the specified torques once components are installed.
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...udza7545918
This document provides instructions for removing and installing components of the fuel transfer pump and governor for Caterpillar 320 excavators. The removal and installation procedures are described in detail over multiple pages with illustrations and required tools listed. Safety and contamination prevention notes are also provided throughout.
Caterpillar Cat 320 N EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...udza7545918
This document provides instructions for removing and installing components of the fuel transfer pump and governor for Caterpillar 320 excavators. The removal and installation procedures are described in detail over multiple pages with illustrations and required tools listed. Safety and contamination prevention notes are also provided throughout.
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...udza7545918
This document provides instructions for removing and installing a fuel transfer pump and governor on Caterpillar 320, 320L, 320N, and 320S excavators powered by a 3116 engine. The removal procedure involves removing covers, seals, springs, fittings and other components of the fuel transfer pump. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order. Similarly, removing the governor requires disconnecting lines and cables before removing mounting bolts, while installation is the reverse of removal.
This document provides instructions for removing and installing components of the fuel transfer pump and governor for Caterpillar 320 excavators. The removal and installation procedures are described in detail over multiple pages with illustrations and required tools listed. Safety and contamination prevention notes are also provided throughout.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and housing bolts. Instructions are given to lift the housing off the engine block using a link bracket and driver group. Reinstallation involves reversing the removal process and tightening the housing bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations are provided for removing the flywheel housing, crankshaft pulley, crankshaft front seal, and other components. Precautions are outlined for cleanliness and fluid containment.
This document provides instructions for removing and installing the crankshaft rear seal, flywheel housing, and crankshaft pulley on a Caterpillar C4.2 engine. It outlines the required tools and steps to disassemble and remove the components. The removal steps include using pullers and drivers to remove the seal, housing, and pulley. The installation steps specify cleaning surfaces, installing new seals and gaskets, and tightening to the specified torque values.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves taking off components like the electric starting motor and flywheel. Tools like a link bracket and driver group are required. Installation involves reversing the removal steps and ensuring proper torque of fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
CASE IH MAXXUM CVX 130 Europe F4DFE413AA Service Repair Manual.pdfudza7545918
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
CASE IH MAXXUM CVX 120 Europe F4DFE413BA Service Repair Manual.pdfudza7545918
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, cab climate control, and electrical systems. Each section provides maintenance and repair information for the corresponding components and systems of the tractors.
CASE IH MAXXUM CVX 110 Europe F4DFE413CA Service Repair Manual.pdfudza7545918
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
CASE IH MAXXUM 140 Multicontroller EP Europe F4DFE6132A Service Repair Manual...udza7545918
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
CASE IH MAXXUM 140 EP Europe F4DFE6132A Service Repair Manual.pdfudza7545918
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains information on engine systems, transmission, four-wheel drive systems, front and rear axles, power take-off, brakes, hydraulics, hitches and couplings, frames, steering, wheels, cab climate control, and electrical systems. Each major system is broken down into specific components and subsystems.
CASE IH MAXXUM 130 Multicontroller EP Europe F4DFE413AA Service Repair Manual...udza7545918
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02766796
Inlet Manifold - Remove and Install
SMCS - 1058-010
Removal Procedure
Start By:
A. Remove the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) -
Remove".
B. Remove the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet Heater -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01375420
1. Remove bolts (1) and remove clip (2) .
Illustration 2 g01384395
2. Remove bolt (4) and remove the washers. Discard the washers.
3. Remove bolts (6) and remove the washers. Discard the washers.
4. Remove bolts (3) and remove manifold (5) .
Illustration 3 g01384434
5. Remove clips (7) .
6. Disconnect harness assemblies (8) .
7. Remove bolts (10) and remove inlet manifold (9) and the gasket.
Installation Procedure
2/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 4 g01384434
1. Position the new inlet manifold gasket. Position inlet manifold (9) and install bolts (10).
Tighten bolts (10) to a torque of 18 ± 2 N·m (13 ± 1 lb ft).
2. Connect harness assemblies (8) and install clips (7) .
Illustration 5 g01384395
3. Position manifold (5) and install bolts (3) .
4. Install new washers and install bolt (4). Tighten bolt (4) to a torque of 34 ± 4 N·m (25 ± 3 lb
ft).
3/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Install new washers and install bolts (6). Tighten bolts (6) to a torque of 34 ± 4 N·m (25 ± 3
lb ft).
Illustration 6 g01375420
6. Install clip (2) and install bolts (1) .
End By:
a. Install the air inlet heater. Refer to Disassembly and Assembly, "Air Inlet Heater - Remove
and Install"
b. Install the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:10:10 UTC+0800 2020
4/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02767700
Inlet and Exhaust Valve Springs - Remove and Install
SMCS - 1108-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
B 9U-6198 Crankshaft Turning Tool 1
Start By:
A. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
B. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted in order to remove the valve springs when the
cylinder head is installed to the engine.
1/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed.
Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder
bore.
NOTICE
Plug the apertures for the push rods in the cylinder head in order to
prevent the entry of loose parts into the engine.
Illustration 1 g01376301
Illustration 2 g01376302
2/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
1. Install Tooling (A) into position on the cylinder head in order to compress a valve spring (4)
for the appropriate piston.
2. Use Tooling (A) in order to compress valve spring (4) and open valve (1) slightly.
Note: Do not compress valve spring (4) so that valve spring retainer (3) touches valve stem
seal (5) .
3. Use Tooling (B) in order to rotate the crankshaft carefully, until the piston touches the
valve.
Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent
valve stems.
4. Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the
piston is at the top dead center position. The valve is now held in a position that allows
valve spring (4) to be safely removed.
Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of
each cylinder. If all valve springs require replacement the procedure can be carried out on
two cylinders at the same time. The procedure can be carried out on the following pairs of
cylinders. 1 with 4 and 2 with 3. Ensure that all of the valve springs are installed before
changing from one pair of cylinders to another pair of cylinders.
NOTICE
Do not turn the crankshaft while the valve springs are removed.
3/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 5. Apply sufficient pressure to Tooling (A) in order to allow removal of valve keepers (2) .
Note: Do not compress valve spring (4) so that valve spring retainer (3) touches valve stem
seal (5) .
Remove valve keepers (2) .
6. Slowly release the pressure on Tooling (A).
7. Remove valve spring retainer (3) and remove valve spring (4) .
8. If necessary, remove valve stem seals (5) .
9. Remove Tooling (A) .
Note: The installation of each set of valve springs (4) must be completed before attempting to
remove the next set of valve springs (4) .
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01376913
4/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 4 g01376302
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (5). Install new valve stem seal (5) onto the valve guide.
2. Install valve spring (4) onto the cylinder head. Position valve spring retainer (3) on valve
spring (4) .
3. Install Tooling (A) in the appropriate position on the cylinder head in order to compress
valve spring (4) .
4. Apply sufficient pressure to Tooling (A) in order to install valve keepers (2). Do not
compress valve spring (4) so that valve spring retainer (3) touches valve stem seal (5) .
5. Carefully release the pressure on Tooling (A) .
End By:
a. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
5/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. b. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:11:07 UTC+0800 2020
6/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02767800
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
C 5P-1720 Seal Pick 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Note the location and orientation of all components for assembly purposes.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
1/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
Illustration 1 g01376164
Typical Example
3. Use a suitable lifting device in order to position cylinder head (1) onto Tooling (A) with the
valve springs upward. The weight of cylinder head (1) is approximately 70 kg (155 lb).
Note: Ensure that cylinder head (1) is kept on a clean, soft surface in order to prevent
damage to the machined face.
Illustration 2 g01376174
2/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g01376184
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Install Tooling (B) on cylinder head (1) in order to compress valve spring (5) .
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
5. Apply sufficient pressure to Tooling (B) in order to remove valve keepers (3). Do not
compress the spring so that valve spring retainer (4) touches valve stem seal (6) .
6. Slowly release the pressure on Tooling (B) .
7. Remove valve spring retainer (4). Remove valve spring (5). Remove valve (2) .
8. Use Tooling (C) in order to remove valve stem seal (6) .
3/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 9. Repeat Steps 4 through 7 for the remaining valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
D 312-8755 Valve Stem Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages and all lubrication passages in the cylinder head are free from debris. Follow Steps
1.a through 1.d in order to inspect the components of the cylinder head assembly. Replace
any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Testing and Adjusting,
"Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and Testing and Adjusting, "Valve Guide - Inspect" for further
information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves ".
e. Inspect valve springs (5) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves ".
4/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g01376184
Illustration 5 g01376926
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Lubricate the stem of valve (2) with clean engine oil. Install valve (2) in the appropriate
position in the cylinder head. Check the depth of valve (2) below the face of the cylinder
head. Refer to Testing and Adjusting, "Valve Depth - Inspect" for more information.
5/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 3. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (6). Use Tooling (C) in order to install new valve stem seal (6) onto the valve guide.
4. Install valve spring (5) onto the cylinder head. Position valve spring retainer (4) on valve
spring (5) .
5. Install Tooling (B) in the appropriate position on cylinder head (1) in order to compress
valve spring (5) .
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
6. Apply sufficient pressure to Tooling (B) in order to install valve keepers (3). Do not
compress spring (5) so that valve spring retainer (4) touches valve stem seal (6) .
7. Carefully release the pressure on Tooling (B) .
8. Repeat Steps 2 through 7 for the remaining valves.
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:12:03 UTC+0800 2020
6/6
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i04625005
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
Typical Example
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:13:00 UTC+0800 2020
4/4
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768108
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 1. Drain the coolant into a suitable container for storage or disposal. Refer to Operation and
Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Illustration 1 g01384719
2. Remove bolts (1) .
3. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:13:57 UTC+0800 2020
2/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g01375411
1. Remove bolts (9) and the washers. Remove cover (8) and gasket (7).
2. Remove nuts (5) and the washers from engine oil cooler cover (4). Remove nuts (6) and the washers
from engine oil cooler cover (4).
3. Remove engine oil cooler core (2) from engine oil cooler cover (4). Remove gaskets (1) and (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:14:54 UTC+0800 2020
2/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02746255
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the gaskets for damage. Replace the components, if necessary.
1/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 1 g01375411
1. Install gaskets (3) and (1) to engine oil cooler core (2). Position engine oil cooler core (2) to engine
oil cooler cover (4).
2. Install the washers and nuts (6). Install the washers and nuts (5).
3. Install gasket (7) and position cover (8). Install the washers and bolts (9).
End By:
a. Install the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun May 24 09:15:50 UTC+0800 2020
2/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D LCR EXCAVATOR TXN
Configuration: 314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768201
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 1 g01384719
1/2
314D LCR Excavator TXN00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/5/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...