This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
1. The document provides instructions for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine.
2. The removal procedure includes using various tools to compress the valve springs, remove the valve keepers and other components, and extract the valves and valve guides.
3. The installation procedure specifies cleaning and lubricating the components, and using tools to reinstall the valve guides at the proper height and compress the springs to reinstall the valves and associated parts.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble and remove the components, cleaning requirements, and installation procedures.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble components like removing valve springs and stem seals, and installing new valve stem seals. Precautions are outlined to keep parts clean and contain fluids during the repair work.
Caterpillar cat 323 d l excavator (prefix gtf) service repair manual (gtf0000...fjjsekmsmmes
This document provides instructions for removing and installing inlet and exhaust valve seats in a C6.4 engine. It describes using various tools to remove the valves, valve guides, and valve seat inserts from the cylinder head. It also details how to clean, inspect, and lubricate components before reinstalling the valve seat inserts, guides, and valves in the proper order and orientation. Protective equipment is recommended to safely compress springs during the process.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...fusjekkdmdmd2w
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a C6.4 engine. It describes using various tools to compress springs, remove components, and install new parts. Removal involves turning the cylinder head upside down, then using a valve seat extractor tool to pull out old inserts. Installation requires cleaning components, lubricating guides, and pressing new inserts into place with an installer tool so they protrude the correct amount. Proper cleaning, compression, and tool use is emphasized to prevent damage and ensure correct assembly.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...ufjksemd8ujd
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly and installation and assembly.
- Safety notices are included to handle parts and fluids properly and avoid injury when working with compressed springs.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...jdkskmdmdm
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly, including cleaning, inspection, and installation of new parts.
- Precautions are provided to keep parts clean, contain fluids, and properly release spring pressure to prevent injury when working on the valves and guides.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...prmy389342
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly and installation and assembly.
- Safety notices are included to handle parts and fluids properly and avoid injury when working with compressed springs.
1. The document provides instructions for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine.
2. The removal procedure includes using various tools to compress the valve springs, remove the valve keepers and other components, and extract the valves and valve guides.
3. The installation procedure specifies cleaning and lubricating the components, and using tools to reinstall the valve guides at the proper height and compress the springs to reinstall the valves and associated parts.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble and remove the components, cleaning requirements, and installation procedures.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble components like removing valve springs and stem seals, and installing new valve stem seals. Precautions are outlined to keep parts clean and contain fluids during the repair work.
Caterpillar cat 323 d l excavator (prefix gtf) service repair manual (gtf0000...fjjsekmsmmes
This document provides instructions for removing and installing inlet and exhaust valve seats in a C6.4 engine. It describes using various tools to remove the valves, valve guides, and valve seat inserts from the cylinder head. It also details how to clean, inspect, and lubricate components before reinstalling the valve seat inserts, guides, and valves in the proper order and orientation. Protective equipment is recommended to safely compress springs during the process.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...fusjekkdmdmd2w
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a C6.4 engine. It describes using various tools to compress springs, remove components, and install new parts. Removal involves turning the cylinder head upside down, then using a valve seat extractor tool to pull out old inserts. Installation requires cleaning components, lubricating guides, and pressing new inserts into place with an installer tool so they protrude the correct amount. Proper cleaning, compression, and tool use is emphasized to prevent damage and ensure correct assembly.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...ufjksemd8ujd
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly and installation and assembly.
- Safety notices are included to handle parts and fluids properly and avoid injury when working with compressed springs.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...jdkskmdmdm
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly, including cleaning, inspection, and installation of new parts.
- Precautions are provided to keep parts clean, contain fluids, and properly release spring pressure to prevent injury when working on the valves and guides.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...prmy389342
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly and installation and assembly.
- Safety notices are included to handle parts and fluids properly and avoid injury when working with compressed springs.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...8ufjsekddm8u
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly and installation and assembly.
- Safety notices are included to handle parts and fluids properly and avoid injury when working with compressed springs.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...f8uesjdkdmdm
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- Key steps include using specialized tools to compress valve springs, extract valve guides and seats, and properly install replacement parts.
- Technicians must take care to keep all parts clean and contain fluids, and follow the exact procedures and torque specifications.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual Instant D...fijsekkdmdm2w
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- Key steps include using specialized tools to compress valve springs, extract valve guides and seats, and properly install replacement parts.
- Technicians must take care to keep components clean and properly orient parts, and follow safety procedures when working with compressed springs.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual Instant D...zan2736ban
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a C6.4 engine. It describes using various tools to compress springs, remove components, and install new parts. Removal involves turning the cylinder head upside down, then using a valve seat extractor tool to pull out old inserts. Installation requires cleaning components, lubricating guides, and pressing new inserts into place with a dedicated tool until they are flush with the cylinder head surface.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual Instant D...fujkskemdmdm4r
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- Key steps include using tooling to compress valve springs and remove components, cleaning parts, lubricating new components, and ensuring proper protrusion of installed parts.
- Safety notices warn of risks such as being struck by released spring forces and containing fluids during inspection and repair.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...km7seydwuhdw
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- Key steps include using tooling to compress valve springs and remove components, cleaning parts, lubricating new components, and ensuring proper protrusion of installed parts.
- Safety notices warn of risks such as being struck by released spring forces and containing fluids during inspection and repair.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- Key steps include using specialized tools to compress valve springs, extract valve guides and seats, and properly install replacement parts.
- Technicians must take care to keep all parts clean and contain fluids, and follow the exact procedures and torque specifications.
Caterpillar cat 323 d l excavator (prefix gtf) service repair manual (gtf0000...fjjskekdmmme
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly, including cleaning, inspection, and installation of new parts.
- Precautions are provided to keep parts clean, contain fluids, and wear protective equipment when working with spring-loaded components.
This document provides instructions for removing and installing various engine components on a Caterpillar 272D2 skid steer loader, including:
- Inlet and exhaust valves, requiring tools to compress springs and remove/install components in the listed order.
- The engine oil cooler, requiring disconnecting hoses and removing mounting screws.
- The engine oil relief valve, requiring removing a plug, seal and spring to access the valve.
- The engine oil pump, accessible after removing the front housing, then removing cover screws and rotors.
This document provides instructions for removing and installing various engine components on a Caterpillar 272D2 skid steer loader, including:
- Inlet and exhaust valves, requiring tools to compress springs and remove/install components in the specified order.
- The engine oil cooler, involving disconnecting hoses and removing/installing seals and screws.
- The engine oil relief valve, requiring removal of a plug, seal and spring before installing in reverse order.
- The engine oil pump, which is removed by taking off a cover and rotors before installation in reverse order.
Safety precautions are provided for components with spring forces, and torque specifications are given for certain fasteners.
This document provides instructions for removing and installing various engine components on a Caterpillar 272D2 skid steer loader, including:
- Inlet and exhaust valves, describing the tools needed and step-by-step removal and installation procedures.
- The engine oil cooler, with illustrations showing its location and the removal and installation steps.
- The engine oil relief valve, again with illustrations and notes on removing the spring and related components.
- The engine oil pump, located in the front housing, with instructions to remove it and reinstall it.
- The water pump, noting safety precautions when working with hot coolant, and illustrated steps for removing and installing the pump, belt, and related parts
This document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including:
- Inlet and exhaust valves, describing the tools needed and step-by-step removal and installation procedures.
- The engine oil cooler, showing the process to disconnect hoses and remove/install the cooler.
- The engine oil relief valve, noting the spring force and steps to remove the plug, spring, and valve.
- The engine oil pump, listing the removal of cover and rotors and installation in reverse order.
- The water pump, outlining draining the cooling system, loosening guards and belts, and removing/installing the pump.
Caterpillar Cat 312D2 and 312D2 L Excavator (Prefix EAB) Service Repair Manua...fijsekkdmdm2w
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, torquing bolts in sequences, and refilling fluids before installing removed components.
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, torquing bolts in sequences, and refilling fluids before installing removed components.
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...fujkse9didkke3
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations accompany each step to show how to disassemble and reassemble the components.
3. Special attention is drawn to cleaning parts and applying threadlocker during installation to prevent contamination and ensure proper component life.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care to contain fluids and properly dispose of them.
Caterpillar Cat 330D L Excavator (Prefix NBD) Service Repair Manual (NBD00001...fujkse9didkke3
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...fujkse9didkke3
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...fujkse9didkke3
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual (JLP00001...fujkse9didkke3
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, housings and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have assistance when removing heavier components weighing over 30 kg.
Caterpillar Cat 330D L Excavator (Prefix ERN) Service Repair Manual (ERN00001...fujkse9didkke3
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
More Related Content
Similar to Caterpillar Cat 311D LRR Excavator (Prefix CLA) Service Repair Manual (CLA00001 and up).pdf
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...8ufjsekddm8u
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly and installation and assembly.
- Safety notices are included to handle parts and fluids properly and avoid injury when working with compressed springs.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...f8uesjdkdmdm
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- Key steps include using specialized tools to compress valve springs, extract valve guides and seats, and properly install replacement parts.
- Technicians must take care to keep all parts clean and contain fluids, and follow the exact procedures and torque specifications.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual Instant D...fijsekkdmdm2w
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- Key steps include using specialized tools to compress valve springs, extract valve guides and seats, and properly install replacement parts.
- Technicians must take care to keep components clean and properly orient parts, and follow safety procedures when working with compressed springs.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual Instant D...zan2736ban
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on a C6.4 engine. It describes using various tools to compress springs, remove components, and install new parts. Removal involves turning the cylinder head upside down, then using a valve seat extractor tool to pull out old inserts. Installation requires cleaning components, lubricating guides, and pressing new inserts into place with a dedicated tool until they are flush with the cylinder head surface.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual Instant D...fujkskemdmdm4r
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- Key steps include using tooling to compress valve springs and remove components, cleaning parts, lubricating new components, and ensuring proper protrusion of installed parts.
- Safety notices warn of risks such as being struck by released spring forces and containing fluids during inspection and repair.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual (GTF00001...km7seydwuhdw
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- Key steps include using tooling to compress valve springs and remove components, cleaning parts, lubricating new components, and ensuring proper protrusion of installed parts.
- Safety notices warn of risks such as being struck by released spring forces and containing fluids during inspection and repair.
Caterpillar Cat 323D L Excavator (Prefix GTF) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- Key steps include using specialized tools to compress valve springs, extract valve guides and seats, and properly install replacement parts.
- Technicians must take care to keep all parts clean and contain fluids, and follow the exact procedures and torque specifications.
Caterpillar cat 323 d l excavator (prefix gtf) service repair manual (gtf0000...fjjskekdmmme
- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly, including cleaning, inspection, and installation of new parts.
- Precautions are provided to keep parts clean, contain fluids, and wear protective equipment when working with spring-loaded components.
This document provides instructions for removing and installing various engine components on a Caterpillar 272D2 skid steer loader, including:
- Inlet and exhaust valves, requiring tools to compress springs and remove/install components in the listed order.
- The engine oil cooler, requiring disconnecting hoses and removing mounting screws.
- The engine oil relief valve, requiring removing a plug, seal and spring to access the valve.
- The engine oil pump, accessible after removing the front housing, then removing cover screws and rotors.
This document provides instructions for removing and installing various engine components on a Caterpillar 272D2 skid steer loader, including:
- Inlet and exhaust valves, requiring tools to compress springs and remove/install components in the specified order.
- The engine oil cooler, involving disconnecting hoses and removing/installing seals and screws.
- The engine oil relief valve, requiring removal of a plug, seal and spring before installing in reverse order.
- The engine oil pump, which is removed by taking off a cover and rotors before installation in reverse order.
Safety precautions are provided for components with spring forces, and torque specifications are given for certain fasteners.
This document provides instructions for removing and installing various engine components on a Caterpillar 272D2 skid steer loader, including:
- Inlet and exhaust valves, describing the tools needed and step-by-step removal and installation procedures.
- The engine oil cooler, with illustrations showing its location and the removal and installation steps.
- The engine oil relief valve, again with illustrations and notes on removing the spring and related components.
- The engine oil pump, located in the front housing, with instructions to remove it and reinstall it.
- The water pump, noting safety precautions when working with hot coolant, and illustrated steps for removing and installing the pump, belt, and related parts
This document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including:
- Inlet and exhaust valves, describing the tools needed and step-by-step removal and installation procedures.
- The engine oil cooler, showing the process to disconnect hoses and remove/install the cooler.
- The engine oil relief valve, noting the spring force and steps to remove the plug, spring, and valve.
- The engine oil pump, listing the removal of cover and rotors and installation in reverse order.
- The water pump, outlining draining the cooling system, loosening guards and belts, and removing/installing the pump.
Caterpillar Cat 312D2 and 312D2 L Excavator (Prefix EAB) Service Repair Manua...fijsekkdmdm2w
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, torquing bolts in sequences, and refilling fluids before installing removed components.
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, torquing bolts in sequences, and refilling fluids before installing removed components.
Similar to Caterpillar Cat 311D LRR Excavator (Prefix CLA) Service Repair Manual (CLA00001 and up).pdf (14)
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...fujkse9didkke3
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations accompany each step to show how to disassemble and reassemble the components.
3. Special attention is drawn to cleaning parts and applying threadlocker during installation to prevent contamination and ensure proper component life.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care to contain fluids and properly dispose of them.
Caterpillar Cat 330D L Excavator (Prefix NBD) Service Repair Manual (NBD00001...fujkse9didkke3
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...fujkse9didkke3
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...fujkse9didkke3
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy components and create a vacuum in the hydraulic system. Precautions are outlined for containing fluids and preventing contamination.
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual (JLP00001...fujkse9didkke3
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, housings and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have assistance when removing heavier components weighing over 30 kg.
Caterpillar Cat 330D L Excavator (Prefix ERN) Service Repair Manual (ERN00001...fujkse9didkke3
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...fujkse9didkke3
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
Caterpillar Cat 330C L Excavator (Prefix JNK) Service Repair Manual (JNK00001...fujkse9didkke3
The document provides instructions for assembling and installing a piston motor (hydraulic fan). It is a 3 page document that details 20 steps for assembly, including installing various components like bearings, seals, springs and retaining rings. It then provides 11 steps for installing the fully assembled piston motor and fan assembly onto mounting brackets on the excavator.
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, housings and other components of the swing drive. Lubricants, tools and torque specifications are also listed.
3. The installation procedure describes 6 steps for installing the assembled swing drive into the excavator frame using lifting devices, bolts, sealants and torque wrenches.
This document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing over 30 individual parts in a specific sequence, including gears, shafts, bearings, seals, and housing components. Special tools are required to remove some parts. Proper lifting equipment and safety precautions are needed due to the heavy weights involved, up to approximately 550 kg for the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar Cat 330C L Excavator (Prefix MCA) Service Repair Manual (MCA00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. It outlines 28 steps for disassembly, removing components like the head, brake piston, plates and discs. It then outlines 13 steps for assembly, including installing seals, bearings, springs and ensuring proper placement of parts. Cleanliness is emphasized throughout the process.
Caterpillar Cat 330C L Excavator (Prefix JCD) Service Repair Manual (JCD00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavators. It outlines 28 steps for disassembly, removing components like the head, springs, brake piston, and bearings. It then outlines 13 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Special tools are listed that may be required for tasks like removing races and seals.
Caterpillar Cat 330C L Excavator (Prefix JAB) Service Repair Manual (JAB00001...fujkse9didkke3
1) The document provides disassembly and assembly instructions for a travel motor on 330C and 330C L excavator models.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, and bearing races.
3) It then describes 29 steps for assembling the travel motor, providing notes on cleaning, lubrication, and proper installation of components like O-rings, pistons, seals, and bolts.
Caterpillar Cat 330C L Excavator (Prefix GKX) Service Repair Manual (GKX00001...fujkse9didkke3
This document provides instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models. It outlines 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then lists 13 steps for reassembling the motor and installing components in the reverse order of disassembly while ensuring cleanliness and applying thread lock compounds as needed.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR CLA
Configuration: 311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02767800
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
C 5P-1720 Seal Pick 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Note the location and orientation of all components for assembly purposes.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
1/6
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
Illustration 1 g01376164
Typical Example
3. Use a suitable lifting device in order to position cylinder head (1) onto Tooling (A) with the
valve springs upward. The weight of cylinder head (1) is approximately 70 kg (155 lb).
Note: Ensure that cylinder head (1) is kept on a clean, soft surface in order to prevent
damage to the machined face.
Illustration 2 g01376174
2/6
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01376184
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Install Tooling (B) on cylinder head (1) in order to compress valve spring (5) .
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
5. Apply sufficient pressure to Tooling (B) in order to remove valve keepers (3). Do not
compress the spring so that valve spring retainer (4) touches valve stem seal (6) .
6. Slowly release the pressure on Tooling (B) .
7. Remove valve spring retainer (4). Remove valve spring (5). Remove valve (2) .
8. Use Tooling (C) in order to remove valve stem seal (6) .
3/6
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 9. Repeat Steps 4 through 7 for the remaining valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
D 312-8755 Valve Stem Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages and all lubrication passages in the cylinder head are free from debris. Follow Steps
1.a through 1.d in order to inspect the components of the cylinder head assembly. Replace
any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Testing and Adjusting,
"Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and Testing and Adjusting, "Valve Guide - Inspect" for further
information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves ".
e. Inspect valve springs (5) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves ".
4/6
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g01376184
Illustration 5 g01376926
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Lubricate the stem of valve (2) with clean engine oil. Install valve (2) in the appropriate
position in the cylinder head. Check the depth of valve (2) below the face of the cylinder
head. Refer to Testing and Adjusting, "Valve Depth - Inspect" for more information.
5/6
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 3. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (6). Use Tooling (C) in order to install new valve stem seal (6) onto the valve guide.
4. Install valve spring (5) onto the cylinder head. Position valve spring retainer (4) on valve
spring (5) .
5. Install Tooling (B) in the appropriate position on cylinder head (1) in order to compress
valve spring (5) .
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
6. Apply sufficient pressure to Tooling (B) in order to install valve keepers (3). Do not
compress spring (5) so that valve spring retainer (4) touches valve stem seal (6) .
7. Carefully release the pressure on Tooling (B) .
8. Repeat Steps 2 through 7 for the remaining valves.
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 30 22:07:28 UTC+0800 2020
6/6
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR CLA
Configuration: 311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i04625005
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
Typical Example
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 30 22:08:24 UTC+0800 2020
4/4
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR CLA
Configuration: 311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768108
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
A. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 1. Drain the coolant into a suitable container for storage or disposal. Refer to Operation and
Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Illustration 1 g01384719
2. Remove bolts (1) .
3. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 30 22:09:19 UTC+0800 2020
2/2
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR CLA
Configuration: 311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g01375411
1. Remove bolts (9) and the washers. Remove cover (8) and gasket (7).
2. Remove nuts (5) and the washers from engine oil cooler cover (4). Remove nuts (6) and the washers
from engine oil cooler cover (4).
3. Remove engine oil cooler core (2) from engine oil cooler cover (4). Remove gaskets (1) and (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 30 22:10:15 UTC+0800 2020
2/2
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR CLA
Configuration: 311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02746255
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the gaskets for damage. Replace the components, if necessary.
1/2
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01375411
1. Install gaskets (3) and (1) to engine oil cooler core (2). Position engine oil cooler core (2) to engine
oil cooler cover (4).
2. Install the washers and nuts (6). Install the washers and nuts (5).
3. Install gasket (7) and position cover (8). Install the washers and bolts (9).
End By:
a. Install the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 30 22:11:11 UTC+0800 2020
2/2
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR CLA
Configuration: 311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768201
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 1 g01384719
1/2
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 1. Install gasket (4) (not shown). Position engine oil cooler (3) and install bolts (2). Tighten
bolts (2) to a torque of 17 ± 2 N·m (13 ± 1 lb ft).
2. Install bolts (1). Tighten bolts (1) to a torque of 32 ± 3 N·m (24 ± 2 lb ft).
3. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling
System Coolant (ELC) - Change".
End By: Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 30 22:12:07 UTC+0800 2020
2/2
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR CLA
Configuration: 311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02768236
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
Start By:
A. Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1/3
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g01384786
1. Remove engine oil relief valve (1). Do not remove bolt (2) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
Illustration 2 g01384786
1. Install engine oil relief valve (1). Tighten engine oil relief valve (1) to a torque of 49 ± 5
N·m (36 ± 4 lb ft). Do not remove bolt (2) .
2/3
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. End By: Install the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 30 22:13:02 UTC+0800 2020
3/3
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR CLA
Configuration: 311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02751881
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
a. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377713
1. Remove engine oil bypass valve (1). Remove gasket (2) (not shown). Discard gasket (2).
1/2
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01377713
1. Install a new gasket (2) (not shown). Install engine oil bypass valve (1). Tighten engine oil
bypass valve (1) to a torque of 69 ± 5 N·m (51 ± 4 lb ft).
End By:
a. Install the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Nov 30 22:13:58 UTC+0800 2020
2/2
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 311D LRR EXCAVATOR CLA
Configuration: 311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02741773
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolts (1) from the cover (2).
2. Remove cover (2) for the engine oil pump from the front housing. Remove gasket (3) (not
shown).
Illustration 2 g00607770
3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
2/4
311D LRR Excavator CLA00001-UP (MACHINE) POWERED BY C4.2 Engine(SEB...
2020/11/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...