The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve if needed. Installation requires heating the sleeve and tightening a nut.
- Removing the crankshaft front seal by drilling holes and pulling it out, being careful not to damage the crankshaft. Installation uses a installer tool and applying oil.
Caterpillar cat 314 d lcr excavator (prefix wln) service repair manual (wln00...soeldksejdksem
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR and 314D LCR Excavator, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve with a chisel if needed, and installing with a driver and ensuring proper torque.
- Removing the crankshaft front seal using a slide hammer puller after drilling holes, and installing the new seal with a front seal installer.
Caterpillar cat 314 d cr excavator (prefix wln) service repair manual (wln000...fjjskekdmmse
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator. Specifically, it details how to remove and install the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the engine's gear group. The procedures include lists of required tools and step-by-step instructions with illustrations. Safety notices are also provided to keep parts clean and contain fluids.
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. It lists the required tools and presents the step-by-step removal and installation procedures in detail with illustrations. The procedures include removing the electric starting motor, flywheel, bolts securing the housing, gasket, and installing the new gasket, housing, bolts, and reinstalling the flywheel and electric starting motor.
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. It lists the required tools and presents the step-by-step removal and installation procedures in detail with illustrations. The procedures include removing the electric starting motor, flywheel, bolts and washers securing the housing, and installing a new gasket. Quality checks are also specified to ensure correct installation.
The document provides instructions for removing and installing various engine components of a Caterpillar 314D CR excavator, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing a new crankshaft front seal.
- Removing the idler gear from the front gear group.
The summaries provide the high level overview of the component being worked on and the main steps for removal and installation in 1-3 concise sentences.
The document provides instructions for removing and installing various engine components of a Caterpillar 314D CR excavator, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing a new crankshaft front seal.
- Removing the idler gear from the front gear group.
The summaries provide the component being worked on and basic steps for removal and installation in 1-3 concise sentences per section summarized.
The document provides instructions for removing and installing various engine components of a Caterpillar 314D CR excavator, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing a new crankshaft front seal.
- Removing the idler gear from the front gear group.
The summaries provide the component being worked on and a brief description of the removal or installation steps in 1-3 sentences per instruction section. Key details like required tools are omitted for brevity.
The document provides instructions for removing and installing various engine components of a Caterpillar 314D CR excavator, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing a new crankshaft front seal.
- Removing the idler gear from the front gear group.
The summaries provide the component being worked on and basic steps for removal and installation in 1-3 concise sentences per section summarized.
Caterpillar cat 314 d lcr excavator (prefix wln) service repair manual (wln00...soeldksejdksem
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR and 314D LCR Excavator, including:
- Removing and installing the flywheel housing, which requires removing bolts and installing a new gasket.
- Removing the crankshaft pulley using pullers and removing the wear sleeve with a chisel if needed, and installing with a driver and ensuring proper torque.
- Removing the crankshaft front seal using a slide hammer puller after drilling holes, and installing the new seal with a front seal installer.
Caterpillar cat 314 d cr excavator (prefix wln) service repair manual (wln000...fjjskekdmmse
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator. Specifically, it details how to remove and install the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the engine's gear group. The procedures include lists of required tools and step-by-step instructions with illustrations. Safety notices are also provided to keep parts clean and contain fluids.
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. It lists the required tools and presents the step-by-step removal and installation procedures in detail with illustrations. The procedures include removing the electric starting motor, flywheel, bolts securing the housing, gasket, and installing the new gasket, housing, bolts, and reinstalling the flywheel and electric starting motor.
The document provides instructions for removing and installing the flywheel housing on a Caterpillar C4.2 engine. It lists the required tools and presents the step-by-step removal and installation procedures in detail with illustrations. The procedures include removing the electric starting motor, flywheel, bolts and washers securing the housing, and installing a new gasket. Quality checks are also specified to ensure correct installation.
The document provides instructions for removing and installing various engine components of a Caterpillar 314D CR excavator, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing a new crankshaft front seal.
- Removing the idler gear from the front gear group.
The summaries provide the high level overview of the component being worked on and the main steps for removal and installation in 1-3 concise sentences.
The document provides instructions for removing and installing various engine components of a Caterpillar 314D CR excavator, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing a new crankshaft front seal.
- Removing the idler gear from the front gear group.
The summaries provide the component being worked on and basic steps for removal and installation in 1-3 concise sentences per section summarized.
The document provides instructions for removing and installing various engine components of a Caterpillar 314D CR excavator, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing a new crankshaft front seal.
- Removing the idler gear from the front gear group.
The summaries provide the component being worked on and a brief description of the removal or installation steps in 1-3 sentences per instruction section. Key details like required tools are omitted for brevity.
The document provides instructions for removing and installing various engine components of a Caterpillar 314D CR excavator, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing a new crankshaft front seal.
- Removing the idler gear from the front gear group.
The summaries provide the component being worked on and basic steps for removal and installation in 1-3 concise sentences per section summarized.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 313D excavator. Specifically, it details procedures for removing and installing the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear from the front gear group. The instructions include lists of required tools and step-by-step processes with illustrations for each procedure.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Cleanliness is emphasized to prevent contamination.
The document provides instructions for removing and installing various engine components on a Caterpillar 313D excavator. Specifically, it details procedures for removing and installing the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear from the front gear group. The instructions include lists of required tools and step-by-step processes with illustrations for each procedure.
Caterpillar cat 313 d excavator (prefix wpk) service repair manual (wpk00001 ...ikdkkdmdmdm
The document provides instructions for removing and installing various components of the C4.2 engine for Caterpillar built machines, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts, cleaning surfaces, and installing replacement components along with specified torques.
The document provides instructions for removing the idler gear from the front gear group of a C4.2 engine. It outlines the necessary tools and steps to:
1. Remove the crankshaft pulley and flywheel housing to access the front gear group.
2. Use a puller tool to remove the idler gear from the front gear group housing.
3. Inspect dowel pins and clean mating surfaces before reinstalling replacement idler gear.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
The document provides instructions for removing and installing various components of the C4.2 engine for Caterpillar built machines, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts, cleaning surfaces, and installing replacement components along with specified torques.
The document provides instructions for disassembling a swing drive from a 320C excavator. It describes:
1) Removing the retaining ring from the swing drive housing using retaining ring pliers.
2) Using a driver group to remove the bearing from the housing.
3) Removing the inner ring, roller assembly, and outer ring from the bearing.
The summary highlights the key steps in the disassembly process without providing all the detail from the original document. It focuses on the essential information needed to understand the high level disassembly procedure.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine, including:
- Removing and installing the fuel filter base
- Removing and installing the fuel injection lines
- Removing the fuel injection nozzles
- Installing new fuel injection nozzles
The summaries provide the high-level steps for each procedure in 3 sentences or less.
The document provides instructions for installing and assembling auxiliary control valves F1, F2, and F4 on a 320C excavator. It describes:
1) Installing the F1 and F4 control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Assembling the F2 control valve by installing O-rings, springs, and other components in the specified order and attaching fittings and plugs.
3) Completing installation by connecting hoses and electrical connectors, installing panels and covers, and filling the hydraulic system.
The document provides instructions for removing and installing various engine components on Caterpillar 320 and 320L track excavators, including:
1) Removing and installing the turbocharger, exhaust manifold, air inlet heater, and inlet manifold. The procedures describe removing bolts, nuts, hoses and other parts and replacing gaskets.
2) Keeping all parts clean to prevent contamination, which can cause rapid wear and shortened component life.
3) Tightening bolts and nuts to the specified torques once components are installed.
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...udza7545918
This document provides instructions for removing and installing components of the fuel transfer pump and governor for Caterpillar 320 excavators. The removal and installation procedures are described in detail over multiple pages with illustrations and required tools listed. Safety and contamination prevention notes are also provided throughout.
Caterpillar Cat 320 N EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...udza7545918
This document provides instructions for removing and installing components of the fuel transfer pump and governor for Caterpillar 320 excavators. The removal and installation procedures are described in detail over multiple pages with illustrations and required tools listed. Safety and contamination prevention notes are also provided throughout.
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...udza7545918
This document provides instructions for removing and installing a fuel transfer pump and governor on Caterpillar 320, 320L, 320N, and 320S excavators powered by a 3116 engine. The removal procedure involves removing covers, seals, springs, fittings and other components of the fuel transfer pump. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order. Similarly, removing the governor requires disconnecting lines and cables before removing mounting bolts, while installation is the reverse of removal.
This document provides instructions for removing and installing components of the fuel transfer pump and governor for Caterpillar 320 excavators. The removal and installation procedures are described in detail over multiple pages with illustrations and required tools listed. Safety and contamination prevention notes are also provided throughout.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and housing bolts. Instructions are given to lift the housing off the engine block using a link bracket and driver group. Reinstallation involves reversing the removal process and tightening the housing bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations are provided for removing the flywheel housing, crankshaft pulley, crankshaft front seal, and other components. Precautions are outlined for cleanliness and fluid containment.
This document provides instructions for removing and installing an inlet manifold and inlet and exhaust valves on a Caterpillar 314D LCR excavator. It describes the required tools, removal process which involves removing mounting bolts and clips, and installation process which involves installing gaskets, bolts, clips and ensuring proper torque specifications. Safety notices are provided regarding keeping parts clean, wearing protective equipment and avoiding damage to components.
This document provides instructions for removing and installing the crankshaft rear seal, flywheel housing, and crankshaft pulley on a Caterpillar C4.2 engine. It outlines the required tools and steps to disassemble and remove the components. The removal steps include using pullers and drivers to remove the seal, housing, and pulley. The installation steps specify cleaning surfaces, installing new seals and gaskets, and tightening to the specified torque values.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves taking off components like the electric starting motor and flywheel. Tools like a link bracket and driver group are required. Installation involves reversing the removal steps and ensuring proper torque of fasteners.
More Related Content
Similar to Caterpillar Cat 314D CR Excavator (Prefix WLN) Service Repair Manual (WLN00001 and up).pdf
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 313D excavator. Specifically, it details procedures for removing and installing the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear from the front gear group. The instructions include lists of required tools and step-by-step processes with illustrations for each procedure.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Cleanliness is emphasized to prevent contamination.
The document provides instructions for removing and installing various engine components on a Caterpillar 313D excavator. Specifically, it details procedures for removing and installing the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear from the front gear group. The instructions include lists of required tools and step-by-step processes with illustrations for each procedure.
Caterpillar cat 313 d excavator (prefix wpk) service repair manual (wpk00001 ...ikdkkdmdmdm
The document provides instructions for removing and installing various components of the C4.2 engine for Caterpillar built machines, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts, cleaning surfaces, and installing replacement components along with specified torques.
The document provides instructions for removing the idler gear from the front gear group of a C4.2 engine. It outlines the necessary tools and steps to:
1. Remove the crankshaft pulley and flywheel housing to access the front gear group.
2. Use a puller tool to remove the idler gear from the front gear group housing.
3. Inspect dowel pins and clean mating surfaces before reinstalling replacement idler gear.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
The document provides instructions for removing and installing various components of the C4.2 engine for Caterpillar built machines, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts, cleaning surfaces, and installing replacement components along with specified torques.
Similar to Caterpillar Cat 314D CR Excavator (Prefix WLN) Service Repair Manual (WLN00001 and up).pdf (8)
The document provides instructions for disassembling a swing drive from a 320C excavator. It describes:
1) Removing the retaining ring from the swing drive housing using retaining ring pliers.
2) Using a driver group to remove the bearing from the housing.
3) Removing the inner ring, roller assembly, and outer ring from the bearing.
The summary highlights the key steps in the disassembly process without providing all the detail from the original document. It focuses on the essential information needed to understand the high level disassembly procedure.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine, including:
- Removing and installing the fuel filter base
- Removing and installing the fuel injection lines
- Removing the fuel injection nozzles
- Installing new fuel injection nozzles
The summaries provide the high-level steps for each procedure in 3 sentences or less.
The document provides instructions for installing and assembling auxiliary control valves F1, F2, and F4 on a 320C excavator. It describes:
1) Installing the F1 and F4 control valves together using existing mount bolts and connecting hoses and electrical connections.
2) Assembling the F2 control valve by installing O-rings, springs, and other components in the specified order and attaching fittings and plugs.
3) Completing installation by connecting hoses and electrical connectors, installing panels and covers, and filling the hydraulic system.
The document provides instructions for removing and installing various engine components on Caterpillar 320 and 320L track excavators, including:
1) Removing and installing the turbocharger, exhaust manifold, air inlet heater, and inlet manifold. The procedures describe removing bolts, nuts, hoses and other parts and replacing gaskets.
2) Keeping all parts clean to prevent contamination, which can cause rapid wear and shortened component life.
3) Tightening bolts and nuts to the specified torques once components are installed.
Caterpillar Cat 320 S EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...udza7545918
This document provides instructions for removing and installing components of the fuel transfer pump and governor for Caterpillar 320 excavators. The removal and installation procedures are described in detail over multiple pages with illustrations and required tools listed. Safety and contamination prevention notes are also provided throughout.
Caterpillar Cat 320 N EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...udza7545918
This document provides instructions for removing and installing components of the fuel transfer pump and governor for Caterpillar 320 excavators. The removal and installation procedures are described in detail over multiple pages with illustrations and required tools listed. Safety and contamination prevention notes are also provided throughout.
Caterpillar Cat 320 L EXCAVATOR (Prefix 9WG) Service Repair Manual (9WG00723 ...udza7545918
This document provides instructions for removing and installing a fuel transfer pump and governor on Caterpillar 320, 320L, 320N, and 320S excavators powered by a 3116 engine. The removal procedure involves removing covers, seals, springs, fittings and other components of the fuel transfer pump. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order. Similarly, removing the governor requires disconnecting lines and cables before removing mounting bolts, while installation is the reverse of removal.
This document provides instructions for removing and installing components of the fuel transfer pump and governor for Caterpillar 320 excavators. The removal and installation procedures are described in detail over multiple pages with illustrations and required tools listed. Safety and contamination prevention notes are also provided throughout.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and housing bolts. Instructions are given to lift the housing off the engine block using a link bracket and driver group. Reinstallation involves reversing the removal process and tightening the housing bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations are provided for removing the flywheel housing, crankshaft pulley, crankshaft front seal, and other components. Precautions are outlined for cleanliness and fluid containment.
This document provides instructions for removing and installing an inlet manifold and inlet and exhaust valves on a Caterpillar 314D LCR excavator. It describes the required tools, removal process which involves removing mounting bolts and clips, and installation process which involves installing gaskets, bolts, clips and ensuring proper torque specifications. Safety notices are provided regarding keeping parts clean, wearing protective equipment and avoiding damage to components.
This document provides instructions for removing and installing the crankshaft rear seal, flywheel housing, and crankshaft pulley on a Caterpillar C4.2 engine. It outlines the required tools and steps to disassemble and remove the components. The removal steps include using pullers and drivers to remove the seal, housing, and pulley. The installation steps specify cleaning surfaces, installing new seals and gaskets, and tightening to the specified torque values.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. The removal procedure involves taking off components like the electric starting motor and flywheel. Tools like a link bracket and driver group are required. Installation involves reversing the removal steps and ensuring proper torque of fasteners.
CASE IH MAXXUM CVX 130 Europe F4DFE413AA Service Repair Manual.pdfudza7545918
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
CASE IH MAXXUM CVX 120 Europe F4DFE413BA Service Repair Manual.pdfudza7545918
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains sections covering the engine, clutch, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, cab climate control, and electrical systems. Each section provides maintenance and repair information for the corresponding components and systems of the tractors.
CASE IH MAXXUM CVX 110 Europe F4DFE413CA Service Repair Manual.pdfudza7545918
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
CASE IH MAXXUM 140 Multicontroller EP Europe F4DFE6132A Service Repair Manual...udza7545918
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
CASE IH MAXXUM 140 EP Europe F4DFE6132A Service Repair Manual.pdfudza7545918
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains information on engine systems, transmission, four-wheel drive systems, front and rear axles, power take-off, brakes, hydraulics, hitches and couplings, frames, steering, wheels, cab climate control, and electrical systems. Each major system is broken down into specific components and subsystems.
CASE IH MAXXUM 130 Multicontroller EP Europe F4DFE413AA Service Repair Manual...udza7545918
This document is a service manual for tractor models MAXXUM 110-140 EP, MAXXUM Multicontroller 110-140 EP, and MAXXUM CVX 110-130. The manual contains over 50 sections covering all major tractor systems, including the engine, transmission, hydraulics, steering, brakes, electrical systems, and more. Each section provides detailed information, component locations, and repair procedures for the parts and subsystems within that section.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D CR EXCAVATOR WLN
Configuration: 314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742697
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Remove the flywheel and ring gear. Refer to Disassembly and Assembly, "Flywheel -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g01374571
1. Install Tooling (A), and a suitable lifting device onto flywheel housing (3).
2. Remove bolts (2) and the washers that secure flywheel housing (3) to the cylinder block.
3. Remove flywheel housing (3). The weight of flywheel (3) is approximately 29 kg (65 lb).
4. Remove gasket (1) (not shown).
Illustration 2 g01374572
5. Use Tooling (B) in order to remove the oil seal (4) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
NOTICE
2/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01374614
1. Use Tooling (B) in order to install the oil seal (4) (not shown).
Illustration 4 g01374571
2. Check the condition of two dowels (not shown). If dowels are damaged, use new parts for
replacement.
3. Clean old gasket (1) (not shown) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
4. Place flywheel housing (3) in position on the cylinder block.
5. Install the washers and bolts (2) in order to secure flywheel housing (3) to the cylinder
block.
6. Remove Tooling (A).
End By:
3/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 5 23:11:15 UTC+0800 2020
4/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D CR EXCAVATOR WLN
Configuration: 314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i06790404
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket(1)
1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Remove the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
1/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 1 g00604778
2. Use Tooling (B) in order to remove nut (1) and washer (2) from the threaded end of the
crankshaft.
Illustration 2 g00604784
3. Use Tooling (A) in order to remove crankshaft pulley (3) from the engine.
2/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 3 g00604792
4. If it is necessary to remove wear sleeve (4) from crankshaft pulley (3), use a suitable
hammer and a suitable chisel. Hold the suitable chisel at right angles to the surface of the
wear sleeve. Tap the wear sleeve in three places. You can remove the wear sleeve once the
tension is released.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 6V-9120 Socket(1)
1
C 1P-0510 Driver Gp 1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Raise the temperature of the wear sleeve. Use Tooling (C) in order to install the wear sleeve
onto the crankshaft pulley.
3/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 4 g01377941
2. Ensure that baffle plate (5) is oriented, as shown.
Illustration 5 g00604778
3. Position crankshaft pulley (3) onto the engine.
4. Install washer (2) and nut (1). Use Tooling (B) in order to tighten nut (1) to a torque of
707.5 ± 57.5 N·m (522 ± 42 lb ft).
5. Install the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 5 23:12:11 UTC+0800 2020
4/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D CR EXCAVATOR WLN
Configuration: 314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742689
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
Typical Example
1. Drill three evenly spaced 3.0 mm (0.12 inch) holes in crankshaft front seal (1).
2. Use Tooling (A) in order to remove crankshaft front seal (1). Remove the seal evenly by
alternating the position of Tooling (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 5 23:13:08 UTC+0800 2020
2/2
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D CR EXCAVATOR WLN
Configuration: 314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742692
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 1 g00612743
Typical Example
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Use Tooling (A) in order to install new crankshaft front seal (1) in the front housing.
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 5 23:14:05 UTC+0800 2020
2/2
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D CR EXCAVATOR WLN
Configuration: 314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 5 g01374810
Illustration 6 g01374811
5. The following items are components of Tooling (A).
◦ 9U-6147 Stud (9)
◦ 6V-8231 Nut (10)
◦ 9U-6146 Sleeve Assembly (11)
◦ 8T-4244 Nut (12)
6. Use Tooling (A) in order to remove idler shaft (8) (not shown) from the cylinder block.
Check idler shaft (8) for wear and damage. Replace idler shaft (8), if necessary.
Note: See the following list for the removal of the other gears in the front gear group.
◦ In order to remove camshaft gear (3), refer to Disassembly and Assembly, "Camshaft
- Remove".
◦ In order to remove fuel injection pump gear (1), refer to Disassembly and Assembly,
"Fuel Injection Pump - Remove".
◦ In order to remove the gear from the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Remove".
◦ In order to remove crankshaft gear (4), refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 5 23:15:02 UTC+0800 2020
4/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D CR EXCAVATOR WLN
Configuration: 314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02879402
Gear Group (Front) - Install - Idler Gear Only
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
a 1p-0510 Driver Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 1 g01374804
1. Use Tooling (A) and a suitable press in order to install a new bushing (7) (not shown), if the
bushing was removed.
Illustration 2 g01374810
2. Lower the temperature of idler shaft (8) . Install idler shaft (8) (not shown) onto the cylinder
block.
Note: When idler shaft (8) is installed, ensure that the oil hole of idler shaft (8) is up.
Illustration 3 g01374827
3. Install idler gear (2) onto idler shaft (8) .
2/5
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 4 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
Illustration 5 g01374789
4. Install thrust plate (6) onto the idler shaft.
5. Install the washer and idler gear bolt (5) onto thrust plate (6) . Tighten idler gear bolt (5) to a
torque of 34 ± 5 N·m (25 ± 4 lb ft).
3/5
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Note: See the following list for the installation of the other gears in the front gear group.
◦ In order to install the camshaft gear, refer to Disassembly and Assembly, "Camshaft -
Install".
◦ In order to install the fuel injection pump gear, refer to Disassembly and Assembly,
"Fuel Injection Pump - Install".
◦ In order to install the gear to the engine oil pump, refer to Disassembly and
Assembly, "Engine Oil Pump - Install".
◦ In order to install the crankshaft front gear, refer to Disassembly and Assembly,
"Crankshaft Gear - Remove and Install".
Illustration 6 g01374841
6. Install a dial indicator and rotate idler gear (2) back and forth in order to measure backlash.
Refer to Table 3.
Table 2
Item Standard at Assembly Service Limit
Backlash of crankshaft gear and
idler gear
0.510 to 0.157 mm (0.0201 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of camshaft gear and
idler gear
0.520 to 0.158 mm (0.0205 to
0.0062 inch)
0.250 mm (0.0098
inch)
Backlash of fuel injection pump
gear and idler gear
0.0560 to 0.205 mm (0.0022 to
0.0081 inch)
0.250 mm (0.0098
inch)
4/5
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. End play of idler gear
0.050 to 0.200 mm (0.0020 to
0.0079 inch)
0.350 mm (0.0138
inch)
Clearance between idler gear
bushing and shaft
0.009 to 0.050 mm (0.0004 to
0.0020 inch)
0.100 mm (0.0039
inch)
Illustration 7 g01374874
7. Measure the end play of idler gear (2) with a feeler gauge. Refer to Table 3.
End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 5 23:15:58 UTC+0800 2020
5/5
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 314D CR EXCAVATOR WLN
Configuration: 314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2 Engine
Disassembly and Assembly
C4.2 Engine for Caterpillar Built Machines
Media Number -KENR8105-04 Publication Date -01/06/2013 Date Updated -12/06/2013
i02743335
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
Start By:
a. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
b. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
c. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
d. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374908
1. Loosen hose clamp (1) that secures hose (2) to the front housing.
2. Disconnect hose (2) from the front housing.
Illustration 2 g00605985
3. Remove bolts (3) and the washers that hold front housing (4) to the plate and the cylinder
block.
2/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. 4. Remove six bolts (5) (not shown) and the washers that mount front housing (4) to the oil
pan.
Illustration 3 g00606002
5. Remove bolts (6) and the washers that mount front housing (4) to front plate (8) and the
cylinder block.
6. Use two people in order to remove front housing (4) from the cylinder block and front plate
(8). The weight of front housing (4) is approximately 20 kg (45 lb).
Note: Check the condition of gasket (7) (not shown) for the engine oil pan. If gasket (7) is
damaged, it may be necessary to replace gasket (7). Refer to Disassembly and Assembly,
"Engine Oil Pan - Remove and Install" for replacement of gasket (7) for the engine oil pan.
3/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 4 g01377884
7. Remove baffle plate (9).
Illustration 5 g01377894
8. Use Tooling (A) in order to remove crankshaft front seal (10) (not shown) from front
housing (4), if necessary.
9. Check the teeth of the timing gears for the following items: wear, nicks, chips and uneven
contact. Check the keyway for wear or damage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 5 23:16:55 UTC+0800 2020
4/4
314D CR & 314D LCR Excavator WLN00001-UP (MACHINE) POWERED BY C4.2...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...