This document provides instructions for disassembling and assembling components of the fuel injection system for a 245 Excavator model engine. The document describes how to disassemble and assemble the fuel injection pump housing, which includes removing pumps, gears, and other internal components. It also provides instructions for removing and installing the inlet manifold and aftercooler. The procedures provide detailed steps for servicing these engine systems while ensuring proper identification and replacement of parts.
This document provides instructions for disassembling and assembling components of the fuel injection system for a 3406 vehicular engine used in 245 excavators. The document describes how to disassemble and assemble the fuel injection pump housing by removing pumps, gears, and other internal components. It also provides instructions for removing and installing the inlet manifold, aftercooler, and related components. The purpose is to provide technicians with step-by-step guidance for servicing and repairing parts of the fuel system.
This document provides instructions for disassembling and assembling components of the fuel injection system for a 3406 vehicular engine used in 245 excavators. The document describes how to disassemble and assemble the fuel injection pump housing by removing pumps, gears, and other internal components. It also provides instructions for removing and installing the inlet manifold, aftercooler, and related components. The purpose is to repair or replace parts while maintaining proper installation and alignment of components.
This document provides instructions for disassembling and assembling components of a 245 Excavator's 3406 vehicular engine, including:
- Removing and installing the fuel injection pump housing, which involves disassembling the pumps and housing components and reassembling them in reverse order.
- Removing the inlet manifold by disconnecting air and fuel lines and removing mounting bolts, and installing it by reversing the removal steps.
- Removing the aftercooler by disconnecting hoses and pipes, removing mounting bolts, and extracting components like the core, housing pieces, and elbows.
This document provides instructions for disassembling and assembling components of a 245 Excavator's 3406 vehicular engine, including:
- Removing and installing the fuel injection pump housing, which involves disassembling the pumps and housing components and reassembling them in reverse order.
- Removing the inlet manifold by disconnecting air and fuel lines and removing mounting bolts, and installing it by reversing the removal steps.
- Removing the aftercooler by disconnecting hoses and pipes, removing mounting bolts, and extracting components like the core, housing pieces, and elbows.
Caterpillar Cat 245 EXCAVATOR (Prefix 95V) Service Repair Manual (95V00001-00...wenxian17880
The document provides instructions for disassembling and assembling components of a 245 Excavator model 95V engine, including:
- Removing and installing the fuel injection pump housing, which involves disassembling the pumps and housing components.
- Removing and installing the inlet manifold (precombustion chamber), which requires disconnecting air lines and removing mounting bolts.
- Removing and installing the aftercooler (direct injection), which involves draining coolant, removing mounting bolts, elbows, and the aftercooler core. Reassembly requires replacing seals and mounting all components back into the housing.
Caterpillar Cat 245 EXCAVATOR (Prefix 95V) Service Repair Manual (95V00001-00...xiapokang564341
The document provides instructions for disassembling and assembling components of a 245 Excavator model 95V engine, including:
- Removing and installing the fuel injection pump housing, which involves disassembling the pumps and housing components.
- Removing and installing the inlet manifold (precombustion chamber), which requires disconnecting air lines and removing mounting bolts.
- Removing and installing the aftercooler (direct injection), which involves draining coolant, removing mounting bolts, elbows, and the aftercooler core. Reassembly requires replacing seals and mounting all components back into the housing.
Caterpillar Cat 245 EXCAVATOR (Prefix 95V) Service Repair Manual (95V00001-00...hvy7sbkw8e
The document provides instructions for disassembling and assembling components of a 245 Excavator model 95V engine, including:
- Removing and installing the fuel injection pump housing, which involves disassembling the pumps and housing components.
- Removing and installing the inlet manifold (precombustion chamber), which requires disconnecting air lines and removing mounting bolts.
- Removing and installing the aftercooler (direct injection), which involves draining coolant, removing mounting bolts, elbows, and the aftercooler core. Reassembly requires replacing seals and mounting all components back into the housing.
This document provides instructions for disassembling and assembling various components of a Caterpillar 3306 vehicular engine, including the governor, fuel transfer pump, fuel check valve, bypass valve, fuel injection pumps, and hood/muffler/precleaner assembly. It describes removing and installing each part in 3 sentences or less, noting key steps like using specific tools, installing parts in their original positions, and ensuring proper orientation of seals and other components.
This document provides instructions for disassembling and assembling components of the fuel injection system for a 3406 vehicular engine used in 245 excavators. The document describes how to disassemble and assemble the fuel injection pump housing by removing pumps, gears, and other internal components. It also provides instructions for removing and installing the inlet manifold, aftercooler, and related components. The purpose is to provide technicians with step-by-step guidance for servicing and repairing parts of the fuel system.
This document provides instructions for disassembling and assembling components of the fuel injection system for a 3406 vehicular engine used in 245 excavators. The document describes how to disassemble and assemble the fuel injection pump housing by removing pumps, gears, and other internal components. It also provides instructions for removing and installing the inlet manifold, aftercooler, and related components. The purpose is to repair or replace parts while maintaining proper installation and alignment of components.
This document provides instructions for disassembling and assembling components of a 245 Excavator's 3406 vehicular engine, including:
- Removing and installing the fuel injection pump housing, which involves disassembling the pumps and housing components and reassembling them in reverse order.
- Removing the inlet manifold by disconnecting air and fuel lines and removing mounting bolts, and installing it by reversing the removal steps.
- Removing the aftercooler by disconnecting hoses and pipes, removing mounting bolts, and extracting components like the core, housing pieces, and elbows.
This document provides instructions for disassembling and assembling components of a 245 Excavator's 3406 vehicular engine, including:
- Removing and installing the fuel injection pump housing, which involves disassembling the pumps and housing components and reassembling them in reverse order.
- Removing the inlet manifold by disconnecting air and fuel lines and removing mounting bolts, and installing it by reversing the removal steps.
- Removing the aftercooler by disconnecting hoses and pipes, removing mounting bolts, and extracting components like the core, housing pieces, and elbows.
Caterpillar Cat 245 EXCAVATOR (Prefix 95V) Service Repair Manual (95V00001-00...wenxian17880
The document provides instructions for disassembling and assembling components of a 245 Excavator model 95V engine, including:
- Removing and installing the fuel injection pump housing, which involves disassembling the pumps and housing components.
- Removing and installing the inlet manifold (precombustion chamber), which requires disconnecting air lines and removing mounting bolts.
- Removing and installing the aftercooler (direct injection), which involves draining coolant, removing mounting bolts, elbows, and the aftercooler core. Reassembly requires replacing seals and mounting all components back into the housing.
Caterpillar Cat 245 EXCAVATOR (Prefix 95V) Service Repair Manual (95V00001-00...xiapokang564341
The document provides instructions for disassembling and assembling components of a 245 Excavator model 95V engine, including:
- Removing and installing the fuel injection pump housing, which involves disassembling the pumps and housing components.
- Removing and installing the inlet manifold (precombustion chamber), which requires disconnecting air lines and removing mounting bolts.
- Removing and installing the aftercooler (direct injection), which involves draining coolant, removing mounting bolts, elbows, and the aftercooler core. Reassembly requires replacing seals and mounting all components back into the housing.
Caterpillar Cat 245 EXCAVATOR (Prefix 95V) Service Repair Manual (95V00001-00...hvy7sbkw8e
The document provides instructions for disassembling and assembling components of a 245 Excavator model 95V engine, including:
- Removing and installing the fuel injection pump housing, which involves disassembling the pumps and housing components.
- Removing and installing the inlet manifold (precombustion chamber), which requires disconnecting air lines and removing mounting bolts.
- Removing and installing the aftercooler (direct injection), which involves draining coolant, removing mounting bolts, elbows, and the aftercooler core. Reassembly requires replacing seals and mounting all components back into the housing.
This document provides instructions for disassembling and assembling various components of a Caterpillar 3306 vehicular engine, including the governor, fuel transfer pump, fuel check valve, bypass valve, fuel injection pumps, and hood/muffler/precleaner assembly. It describes removing and installing each part in 3 sentences or less, noting key steps like using specific tools, installing parts in their original positions, and ensuring proper orientation of seals and other components.
This document provides instructions for disassembling and assembling various components of a Caterpillar 3306 vehicular engine, including the governor, fuel transfer pump, fuel check valve, bypass valve, fuel injection pumps, and hood/muffler/precleaner assembly. It lists the specific parts to remove and install for each component, and the order and important notes for the process. Disassembly generally involves removing covers, seals, springs, pins, and internal parts. Reassembly follows the reverse order and notes proper orientation of parts.
This document provides instructions for disassembling and assembling various components of a 977K Track Loader engine, including the governor, fuel transfer pump, fuel check valve, fuel injection pumps, and hood/muffler/precleaner assembly. It describes removing and installing each part in 3 sentences or less per component, identifying start and end steps and noting important details like installation order and specific tools required.
This document provides instructions for disassembling and assembling various components of a 977K track loader, including the fuel injection pump housing, governor, and engine. The instructions include removing and installing over 50 individual parts in a specific sequence, noting identification numbers, lubrication, and torque specifications where relevant. Key steps include separating the governor from the fuel injection pump housing, removing the fuel injection pumps, camshaft and other internal parts, and correctly reinstalling them while aligning pins, levers and shafts.
This document provides instructions for disassembling and assembling various components of a 977K track loader, including the fuel injection pump housing, governor, and engine. The instructions include removing and installing over 50 individual parts in a specific sequence, noting identification numbers, lubrication, and torque specifications where relevant. Key steps include separating the governor from the fuel injection pump housing, removing the fuel injection pumps, camshaft and other internal parts, and correctly reinstalling them while aligning pins, levers and shafts.
This document provides instructions for disassembling and assembling various components of a 977K track loader, including the fuel injection pump housing, governor, and engine. The instructions include removing and installing over 50 individual parts in a specific sequence, noting identification numbers, lubrication, and torque specifications where relevant. Key steps include separating the governor from the fuel injection pump housing, removing the fuel injection pumps, camshaft and other internal parts, and correctly reinstalling them while aligning pins, levers and shafts.
The document provides instructions for disassembling and assembling various components of a 955K track loader engine, including:
1) Separating and reconnecting the governor from the fuel injection pump housing.
2) Disassembling and reassembling the governor.
3) Removing and installing the fuel check valve and bypass valve.
4) Taking out and putting in the fuel injection pumps.
5) Taking apart and rebuilding the fuel injection pumps.
1. The document provides instructions for disassembling and assembling various components of a 955K track loader engine, including the governor, fuel injection pumps, fuel check valve, and bypass valve.
2. Steps are provided to separate the governor from the fuel injection pump housing, disassemble the governor, remove and install the fuel check valve and bypass valve, remove and install the fuel injection pumps, and disassemble and assemble the fuel injection pumps.
3. Cleaning procedures and special notes are included throughout to ensure correct assembly.
The document provides instructions for disassembling and assembling various components of a 955K track loader engine, including:
1) Separating and reconnecting the governor from the fuel injection pump housing.
2) Disassembling and assembling the governor.
3) Removing and installing the fuel check valve and bypass valve.
The instructions are presented in a step-by-step format with pictures to aid in the process. Proper installation of parts is emphasized to ensure correct engine operation.
This document provides instructions for disassembling and assembling various components of a 977K Track Loader, including the fuel injection pump housing, governor, and engine. The summary is:
1) The fuel injection pump housing and governor must be removed to access internal components. This involves disconnecting lines, removing mounts, and using tools to ensure the engine is in the correct position.
2) Disassembling the governor housing separates components like springs, pins, and flyweights. The fuel injection pump housing is also disassembled to remove the camshaft and internal levers.
3) Reassembly requires installing components in reverse order, ensuring correct positioning, and using new seals and bolts as specified
This document provides instructions for disassembling and assembling various components of a 977K Track Loader, including the fuel injection pump housing, governor, and engine. The summary is:
1) The fuel injection pump housing and governor must be removed to access internal components. This involves disconnecting lines, removing mounts, and using tools to ensure the engine is in the correct position.
2) Disassembly of the governor involves removing springs, seals, pins, and other small parts. The fuel injection pump housing is disassembled by removing the camshaft, lifters, and control shaft.
3) Reassembly follows the reverse order, taking care to install parts correctly and apply new seals, bol
This document provides instructions for disassembling and assembling various components of a 977K Track Loader, including the fuel injection pump housing, governor, and engine. The summary is:
1) The fuel injection pump housing and governor must be removed to access internal components. This involves disconnecting lines, removing mounts, and using tools to ensure the engine is in the correct position.
2) Disassembling the governor housing separates components like springs, pins, and flyweights. The fuel injection pump housing is also disassembled to remove the camshaft and internal levers.
3) Reassembly requires precisely positioning each part and uses new seals, bolts and tools to apply torque. The process
This document provides instructions for disassembling and assembling components of a sleeve metering fuel system for a D7F track-type tractor, including:
1) Disassembling and assembling the governor, removing and installing fuel check valves and bypass valves, and removing and installing fuel injection pumps.
2) Detailed steps are provided for removing each part and reinstalling them in the proper order.
3) Precautions are outlined, such as ensuring parts are kept with their respective barrels during disassembly and reinstallation.
This document provides instructions for disassembling and assembling components of a fuel system for a D7F track-type tractor, including:
1) Disassembling and assembling the governor, removing and installing fuel check valves and bypass valves, and removing and installing fuel injection pumps.
2) Detailed steps are provided for disassembling and assembling the governor, fuel check valve and bypass valve, and fuel injection pumps.
3) Instructions are also given for removing and installing the fuel transfer pump.
This document provides instructions for disassembling and assembling components of a sleeve metering fuel system for a D7F track-type tractor, including:
1) Disassembling and assembling the governor, removing and installing fuel check valves and bypass valves, and removing and installing fuel injection pumps.
2) Detailed steps are provided for removing each part and reinstalling them in the proper order.
3) Precautions are outlined, such as ensuring parts are kept with their respective barrels during disassembly and reinstallation.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves cleaning the crankshaft, applying retaining compound, and pressing the new seal into place using a slide hammer puller. Care must be taken not to damage the crankshaft flange during installation.
This document provides instructions for removing and installing track carrier rollers, track rollers, and separating the track on a 320C Excavator. It describes:
1) Releasing tension on the track and loosening a relief valve before removing components.
2) Using tools like a hydraulic jack and lifting forks to support the track assembly and remove rollers and bolts.
3) Cleaning surfaces, positioning components, and reinstalling bolts and rollers in the reverse order of removal.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320C excavator. The oil pump removal instructions involve removing bolts, gears, seals and other components. The installation involves cleaning parts, pressing components, heating items, and torquing bolts. The water pump instructions describe draining coolant and removing four bolts to take off the pump. Reassembly involves installing seals, bearings and an impeller on a shaft.
This document provides instructions for assembling and disassembling parts of a 320 GC Excavator model BR4, including the travel motor and final drive. It lists the required tools and parts and includes illustrations of the assembly and disassembly procedures. The travel motor assembly instructions involve installing positioning rods and lifting eyes to hold parts in place while bolts are tightened. The final drive disassembly involves removing the final drive housing from the excavator and using link brackets and forcing screws to separate connected components.
Caterpillar Cat 305.5 Mini Hydraulic Excavator (Prefix DCK) Service Repair Ma...f8usejkdmmd8i
The document provides instructions for removing and installing track components on a 305.5 Mini Hydraulic Excavator, including:
- Removing and installing track rollers by raising the machine, removing bolts, and lowering it onto cribbing
- Separating the track by rotating it, removing shoes and bolts, and removing the master pin
- Reconnecting the track by installing the master pin and shoes with bolts
- Removing the front idler and track adjuster by sliding the track assembly away and lifting it off
- Installing the front idler and track adjuster by lifting it into place and sliding the track assembly over it
- Removing the recoil spring assembly
This document provides instructions for installing the fuel injection pump housing and governor on an excavator engine. It outlines 18 steps, including setting the number 1 piston to top center, installing timing pins, attaching the housing and governor, and connecting various lines and covers. Tools required include an engine turning tool, spanner wrench, and two fuel pump timing pins. Precise timing of the fuel injection pump camshaft is critical when attaching the housing.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix HC5) Service Repair ...f8usejkdmmd8i
The document provides instructions for removing and installing various components of a 304E2 CR Mini Hydraulic Excavator engine, including the fuel manifold rail, fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, and electronic unit injector. Safety precautions are outlined that must be followed when working on the fuel system, such as risks of high pressure fuel and containing any spilled fluids.
More Related Content
Similar to Caterpillar Cat 245 EXCAVATOR (Prefix 95V) Service Repair Manual Instant Download.pdf
This document provides instructions for disassembling and assembling various components of a Caterpillar 3306 vehicular engine, including the governor, fuel transfer pump, fuel check valve, bypass valve, fuel injection pumps, and hood/muffler/precleaner assembly. It lists the specific parts to remove and install for each component, and the order and important notes for the process. Disassembly generally involves removing covers, seals, springs, pins, and internal parts. Reassembly follows the reverse order and notes proper orientation of parts.
This document provides instructions for disassembling and assembling various components of a 977K Track Loader engine, including the governor, fuel transfer pump, fuel check valve, fuel injection pumps, and hood/muffler/precleaner assembly. It describes removing and installing each part in 3 sentences or less per component, identifying start and end steps and noting important details like installation order and specific tools required.
This document provides instructions for disassembling and assembling various components of a 977K track loader, including the fuel injection pump housing, governor, and engine. The instructions include removing and installing over 50 individual parts in a specific sequence, noting identification numbers, lubrication, and torque specifications where relevant. Key steps include separating the governor from the fuel injection pump housing, removing the fuel injection pumps, camshaft and other internal parts, and correctly reinstalling them while aligning pins, levers and shafts.
This document provides instructions for disassembling and assembling various components of a 977K track loader, including the fuel injection pump housing, governor, and engine. The instructions include removing and installing over 50 individual parts in a specific sequence, noting identification numbers, lubrication, and torque specifications where relevant. Key steps include separating the governor from the fuel injection pump housing, removing the fuel injection pumps, camshaft and other internal parts, and correctly reinstalling them while aligning pins, levers and shafts.
This document provides instructions for disassembling and assembling various components of a 977K track loader, including the fuel injection pump housing, governor, and engine. The instructions include removing and installing over 50 individual parts in a specific sequence, noting identification numbers, lubrication, and torque specifications where relevant. Key steps include separating the governor from the fuel injection pump housing, removing the fuel injection pumps, camshaft and other internal parts, and correctly reinstalling them while aligning pins, levers and shafts.
The document provides instructions for disassembling and assembling various components of a 955K track loader engine, including:
1) Separating and reconnecting the governor from the fuel injection pump housing.
2) Disassembling and reassembling the governor.
3) Removing and installing the fuel check valve and bypass valve.
4) Taking out and putting in the fuel injection pumps.
5) Taking apart and rebuilding the fuel injection pumps.
1. The document provides instructions for disassembling and assembling various components of a 955K track loader engine, including the governor, fuel injection pumps, fuel check valve, and bypass valve.
2. Steps are provided to separate the governor from the fuel injection pump housing, disassemble the governor, remove and install the fuel check valve and bypass valve, remove and install the fuel injection pumps, and disassemble and assemble the fuel injection pumps.
3. Cleaning procedures and special notes are included throughout to ensure correct assembly.
The document provides instructions for disassembling and assembling various components of a 955K track loader engine, including:
1) Separating and reconnecting the governor from the fuel injection pump housing.
2) Disassembling and assembling the governor.
3) Removing and installing the fuel check valve and bypass valve.
The instructions are presented in a step-by-step format with pictures to aid in the process. Proper installation of parts is emphasized to ensure correct engine operation.
This document provides instructions for disassembling and assembling various components of a 977K Track Loader, including the fuel injection pump housing, governor, and engine. The summary is:
1) The fuel injection pump housing and governor must be removed to access internal components. This involves disconnecting lines, removing mounts, and using tools to ensure the engine is in the correct position.
2) Disassembling the governor housing separates components like springs, pins, and flyweights. The fuel injection pump housing is also disassembled to remove the camshaft and internal levers.
3) Reassembly requires installing components in reverse order, ensuring correct positioning, and using new seals and bolts as specified
This document provides instructions for disassembling and assembling various components of a 977K Track Loader, including the fuel injection pump housing, governor, and engine. The summary is:
1) The fuel injection pump housing and governor must be removed to access internal components. This involves disconnecting lines, removing mounts, and using tools to ensure the engine is in the correct position.
2) Disassembly of the governor involves removing springs, seals, pins, and other small parts. The fuel injection pump housing is disassembled by removing the camshaft, lifters, and control shaft.
3) Reassembly follows the reverse order, taking care to install parts correctly and apply new seals, bol
This document provides instructions for disassembling and assembling various components of a 977K Track Loader, including the fuel injection pump housing, governor, and engine. The summary is:
1) The fuel injection pump housing and governor must be removed to access internal components. This involves disconnecting lines, removing mounts, and using tools to ensure the engine is in the correct position.
2) Disassembling the governor housing separates components like springs, pins, and flyweights. The fuel injection pump housing is also disassembled to remove the camshaft and internal levers.
3) Reassembly requires precisely positioning each part and uses new seals, bolts and tools to apply torque. The process
This document provides instructions for disassembling and assembling components of a sleeve metering fuel system for a D7F track-type tractor, including:
1) Disassembling and assembling the governor, removing and installing fuel check valves and bypass valves, and removing and installing fuel injection pumps.
2) Detailed steps are provided for removing each part and reinstalling them in the proper order.
3) Precautions are outlined, such as ensuring parts are kept with their respective barrels during disassembly and reinstallation.
This document provides instructions for disassembling and assembling components of a fuel system for a D7F track-type tractor, including:
1) Disassembling and assembling the governor, removing and installing fuel check valves and bypass valves, and removing and installing fuel injection pumps.
2) Detailed steps are provided for disassembling and assembling the governor, fuel check valve and bypass valve, and fuel injection pumps.
3) Instructions are also given for removing and installing the fuel transfer pump.
This document provides instructions for disassembling and assembling components of a sleeve metering fuel system for a D7F track-type tractor, including:
1) Disassembling and assembling the governor, removing and installing fuel check valves and bypass valves, and removing and installing fuel injection pumps.
2) Detailed steps are provided for removing each part and reinstalling them in the proper order.
3) Precautions are outlined, such as ensuring parts are kept with their respective barrels during disassembly and reinstallation.
Similar to Caterpillar Cat 245 EXCAVATOR (Prefix 95V) Service Repair Manual Instant Download.pdf (14)
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves cleaning the crankshaft, applying retaining compound, and pressing the new seal into place using a slide hammer puller. Care must be taken not to damage the crankshaft flange during installation.
This document provides instructions for removing and installing track carrier rollers, track rollers, and separating the track on a 320C Excavator. It describes:
1) Releasing tension on the track and loosening a relief valve before removing components.
2) Using tools like a hydraulic jack and lifting forks to support the track assembly and remove rollers and bolts.
3) Cleaning surfaces, positioning components, and reinstalling bolts and rollers in the reverse order of removal.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320C excavator. The oil pump removal instructions involve removing bolts, gears, seals and other components. The installation involves cleaning parts, pressing components, heating items, and torquing bolts. The water pump instructions describe draining coolant and removing four bolts to take off the pump. Reassembly involves installing seals, bearings and an impeller on a shaft.
This document provides instructions for assembling and disassembling parts of a 320 GC Excavator model BR4, including the travel motor and final drive. It lists the required tools and parts and includes illustrations of the assembly and disassembly procedures. The travel motor assembly instructions involve installing positioning rods and lifting eyes to hold parts in place while bolts are tightened. The final drive disassembly involves removing the final drive housing from the excavator and using link brackets and forcing screws to separate connected components.
Caterpillar Cat 305.5 Mini Hydraulic Excavator (Prefix DCK) Service Repair Ma...f8usejkdmmd8i
The document provides instructions for removing and installing track components on a 305.5 Mini Hydraulic Excavator, including:
- Removing and installing track rollers by raising the machine, removing bolts, and lowering it onto cribbing
- Separating the track by rotating it, removing shoes and bolts, and removing the master pin
- Reconnecting the track by installing the master pin and shoes with bolts
- Removing the front idler and track adjuster by sliding the track assembly away and lifting it off
- Installing the front idler and track adjuster by lifting it into place and sliding the track assembly over it
- Removing the recoil spring assembly
This document provides instructions for installing the fuel injection pump housing and governor on an excavator engine. It outlines 18 steps, including setting the number 1 piston to top center, installing timing pins, attaching the housing and governor, and connecting various lines and covers. Tools required include an engine turning tool, spanner wrench, and two fuel pump timing pins. Precise timing of the fuel injection pump camshaft is critical when attaching the housing.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix HC5) Service Repair ...f8usejkdmmd8i
The document provides instructions for removing and installing various components of a 304E2 CR Mini Hydraulic Excavator engine, including the fuel manifold rail, fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, and electronic unit injector. Safety precautions are outlined that must be followed when working on the fuel system, such as risks of high pressure fuel and containing any spilled fluids.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix ZGZ) Service Repair Manu...f8usejkdmmd8i
The document provides instructions for disassembling and assembling the final drive of a 319D L excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling the final drive, including pressing in bearings, installing seals, and determining the correct shim thickness. The overall procedure involves separating, cleaning, and reassembling over 15 individual parts and components of the final drive.
Caterpillar Cat 319D L Excavator (Prefix KRM) Service Repair Manual Instant D...f8usejkdmmd8i
This document provides instructions for disassembling and assembling the final drive of a 319D L excavator. It describes 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It also describes 31 steps for reassembling these components, including pressing in bearings, determining shim thickness, and installing seals using a special tool. Proper cleaning, lubrication, and use of replacement parts is emphasized throughout.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix CJ2) Service Repair ...f8usejkdmmd8i
The document provides instructions for servicing components of a 304E2CR Mini Hydraulic Excavator engine. It describes procedures for removing and installing the crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The steps include using the proper tools, cleaning parts, applying sealant, and tightening to the specified torque values.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...f8usejkdmmd8i
The document provides instructions for removing and installing various engine components on a 304E2CR Mini Hydraulic Excavator including the crankshaft rear seal carrier, flywheel housing, crankshaft pulley, crankshaft front seal, idler gear, front housing, and valve mechanism cover. The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Precautions are provided regarding keeping parts clean and containing fluids.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix FC2) Service Repair ...f8usejkdmmd8i
The document provides instructions for removing and installing an engine oil cooler on a Caterpillar 304E2CR mini hydraulic excavator. The steps include draining coolant, removing hoses and clamps connecting the cooler, and removing mounting bolts. Reinstallation is the reverse of removal. Proper cleaning and torqueing of connections is emphasized.
Caterpillar Cat 304E Mini Hydraulic Excavator (Prefix TSR) Service Repair Man...f8usejkdmmd8i
This document provides instructions for removing and installing various track components on a 304E Mini Hydraulic Excavator, including the evaporator coil, track carrier roller, track roller, track, front idler, recoil spring, and hydraulic track adjuster. The procedures note required tools and safety precautions, and include illustrations and multiple step-by-step instructions for each component.
Caterpillar Cat 305.5 Mini Hydraulic Excavator (Prefix CXZ) Service Repair Ma...f8usejkdmmd8i
The document is a service repair manual that provides instructions for removing and installing components like the sprocket, final drive, and travel motor on a 305.5 Mini Hydraulic Excavator. It includes detailed removal and installation procedures with illustrations and lists required tools. Procedures include draining fluids, removing bolts and covers, disconnecting hoses, and lifting out heavy components. Disassembly steps describe removing gears, bearings, springs, and other internal parts.
Caterpillar Cat 304E Mini Hydraulic Excavator (Prefix TTN) Service Repair Man...f8usejkdmmd8i
The document provides instructions for servicing a 304E Mini Hydraulic Excavator. It describes procedures for removing and installing the sprocket and removing the final drive and travel motor. The final drive and travel motor are then disassembled by removing gears, bearings, seals, springs, and other internal components using the specified tools. Detailed illustrations accompany each step.
Caterpillar Cat 303.5E2CR Mini Hydraulic Excavator (Prefix CR6) Service Repai...f8usejkdmmd8i
This document provides instructions for installing and removing the governor and camshaft, and fuel injection pump on a 303.5E2CR Mini Hydraulic Excavator. It includes illustrations and step-by-step instructions for disassembling, cleaning, and reassembling these components. The instructions note to keep all parts clean and free of contaminants to prevent premature wear.
Caterpillar Cat 301.6C and 301.8C Mini Hydraulic Excavator (Prefix JSB) Servi...f8usejkdmmd8i
The document provides instructions for removing and disassembling various components of 301.6C and 301.8C mini hydraulic excavators, including the final drive and travel motor. The removal process involves draining fluids, disconnecting hoses, and removing bolts. Disassembly of the final drive and travel motor further requires removing retaining rings, springs, pins, seals and additional components using various specialized tools. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 140M 3 MOTOR GRADER (Prefix N9M) Service Repair Manual Instan...f8usejkdmmd8i
1) The document provides instructions for disassembling the bank valve on the front and rear frames of a Caterpillar 140M 3 motor grader.
2) It describes removing 17 parts from the front bank valve including covers, seals, control valves, plugs, springs, balls, and fittings. Special precautions are listed for releasing spring forces.
3) Disassembling the rear bank valve involves removing 14 parts like covers, seals, control valves, plugs, springs, and tie rods. Again, warnings are given for spring-loaded components.
Caterpillar Cat 140M 2 MOTOR GRADER (Prefix M9D) Service Repair Manual Instan...f8usejkdmmd8i
This document provides assembly instructions for a transmission in a 140M 2 motor grader. It lists required tools and parts and provides step-by-step instructions with accompanying illustrations. The transmission assembly involves installing bearings, gears, seals, pistons, clutches, and housing components in the specified order and with the correct torques. Proper cleaning, heating, lifting, and safety procedures are noted throughout the detailed assembly process.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 245 EXCAVATOR 95V
Configuration: 245 EXCAVATOR 95V00001-00470 (MACHINE)
Disassembly and Assembly
3406 VEHICULAR ENGINE FOR 245 EXCAVATORS
Media Number -SENR7338-01 Publication Date -01/06/1979 Date Updated -12/10/2001
Fuel Injection Pump Housing
SMCS - 1253-15; 1253-16
Disassemble Fuel Injection Pump Housing
start by:
a) separation of governor from fuel injection pump housing
1/8
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. Remove protection caps and felt washers (1) from pumps.
2. Use wrench (A) to remove the bushings (2) that hold fuel injection pumps into housing.
Remove the seals (3).
3. Use extractor (B) to remove pumps from the pump housing.
NOTE: Fuel injection pumps for direct injection and precombustion chamber engines are similar.
See Illustration A96047X1 on Page 38.
4. Remove the bonnet (4), ring (5), spring (6), and check valve (7) from barrel (8).
5. Remove the plunger assembly (11), washer (10), and spring (9) from barrel.
NOTICE
2/8
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Be careful not to cause damage to plunger assemblies. Keep same
cylinder pump and plunger together, the plunger from one pump
cannot be installed in another pump.
6. Remove the rack (12) from the housing.
7. Remove the spacers (13) and the lifters (14) from the housing.
NOTE: Keep the spacers and lifters together with identification as to their location in the pump
housing.
8. Remove two bolts (16), lock, and two sleeves from the gear assembly.
9. Remove the gear assembly (15) from camshaft.
3/8
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 10. Remove two bolts, plate (17), and spacer that hold camshaft in position in pump housing.
11. Remove the camshaft from the pump housing.
12. Use tool group (C) to remove the camshaft bearings from the pump housing.
13. Remove the bearings for fuel rack from the pump housing.
Assemble Fuel Injection Pump Housing
4/8
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 1. Use tool group (C) to install the camshaft bearings in fuel injection pump housing. Install
bearing in governor end of housing so oil hole in bearing is in alignment with oil hole in housing.
2. Use tooling (F) to install bearing with a groove for the rack.
3. Use tooling (E) to install the other bearing for the rack.
4. Put clean engine oil on the camshaft. Install the camshaft in the pump housing.
5. Install the spacer, plate (1), and two bolts that hold camshaft in place in pump housing.
5/8
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 6. Put the gear assembly (2) in position on end of camshaft. Be sure the rod (3) is in the groove of
camshaft.
7. Install the sleeves (4), lock, and two bolts on the gear assembly.
8. Install the spacers (5) with their respective lifters (6) in pump housing. If new lifters and/or
pumps are to be installed, make adjustment of fuel pump timing dimension. See SETTING THE
INJECTION PUMP TIMING DIMENSION: OFF ENGINE in 3406 VEHICLE ENGINE,
TESTING AND ADJUSTING.
9. Install the rack (7) in the pump housing.
10. Assemble the fuel injection pumps as follows:
a) Put clean fuel on all parts.
6/8
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. b) Install spring, washers, and plunger in the barrel.
c) Install the spring, check valve, bonnet, and ring on the barrel.
NOTICE
The plunger from one pump can not be installed in another pump. Do
not install the pumps until rack (7) is in center position (centered).
11. Use pointer group (D) to put rack (7) in center position. Push the rack into pointer (D) to get
the center position.
NOTE: The rack will be extended .156 in. (3.963 mm) from the end of pump housing (opposite
the governor) when rack is in center position.
12. Install fuel injection pumps with extractor (B). Turn the camshaft until lobe of camshaft is
down on pump to be installed. Look down the pump and make grooves in bonnet and barrel in
alignment with groove (slot) in the pump gear. The groove (slot) of gear must be in line with
center of these grooves. Put the pump so grooves are in alignment with guide pins in housing
bores. Install the pump in its respective bore in housing.
13. Install seal (8) and bushing (9). Put pressure by hand to extractor (B). Tighten bushing by hand
(finger tight only) until bushing is even with top of housing. If bushing can not be installed by
hand, remove bushing and pump. Make grooves in alignment and install again.
NOTICE
7/8
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Do not put force on bushings by installation with a wrench to make it
even with pump housing. Pump is not installed correctly if force has to
be used to install bushing.
14. Check the rack movement (travel) after each pump is installed. Total rack movement (travel)
must be .800 in. (20.32 mm). See INSTALLATION OF INJECTION PUMPS in 3406 VEHICLE
ENGINE, TESTING AND ADJUSTING.
15. Tighten the bushing with wrench (A) to a torque of 150 ± 10 lb.ft. (205 ± 14 N·m). Remove
wrench (A) and install felt seals and protection caps.
end by:
a) connection of governor to fuel injection pump housing.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 11 23:51:04 UTC+0800 2019
8/8
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 245 EXCAVATOR 95V
Configuration: 245 EXCAVATOR 95V00001-00470 (MACHINE)
Disassembly and Assembly
3406 VEHICULAR ENGINE FOR 245 EXCAVATORS
Media Number -SENR7338-01 Publication Date -01/06/1979 Date Updated -12/10/2001
Inlet Manifold (Precombustion Chamber)
SMCS - 1058-11; 1058-12
Remove Inlet Manifold (Precombustion Chamber)
1. Disconnect the air line from the precleaner to the muffler.
2. Loosen clamp (1). Move the precleaner up and clear of the elbow (4).
3. Remove bolts (2). Loosen clamp (3). Remove elbow (4).
4. Remove bolts (6) that hold the elbow to the inlet manifold.
5. Disconnect line (8) for the fuel ratio control.
1/2
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 6. Remove bolts (7) that hold the inlet manifold to the cylinder head.
7. Remove inlet manifold (5) and the gaskets.
Install Inlet Manifold (Precombustion Chamber)
1. Put the gaskets and inlet manifold (1) in position on the cylinder head. Install the bolts that hold
it.
2. Install the bolts that hold elbow (2) to the inlet manifold.
3. Connect line (3) for the fuel ratio control to the inlet manifold.
4. Put the elbow for the air cleaner inlet in position on the inlet manifold and air cleaner housing.
Install the bolts that hold the elbow to the inlet manifold. Tighten the clamp that holds it to the air
cleaner housing.
5. Put the precleaner in position on the elbow. Tighten the clamp that holds it.
6. Connect the air line from the precleaner to the muffler.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 11 23:52:00 UTC+0800 2019
2/2
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 245 EXCAVATOR 95V
Configuration: 245 EXCAVATOR 95V00001-00470 (MACHINE)
Disassembly and Assembly
3406 VEHICULAR ENGINE FOR 245 EXCAVATORS
Media Number -SENR7338-01 Publication Date -01/06/1979 Date Updated -12/10/2001
Aftercooler (Direct Injection)
SMCS - 1063-11; 1063-12
Remove Aftercooler (Direct Injection)
NOTE: Engine is removed from the machine for photo purposes only.
1. Remove the hood section over the aftercooler.
2. Drain the coolant to a level below the aftercooler.
3. Loosen clamp (1). Disconnect the hose from the precleaner.
4. Remove bolts (2) and spacers that hold the elbow to the aftercooler housing.
5. Loosen clamp (3). Remove elbow (4) and precleaner from the engine as a unit.
6. Remove bolts (5). Pull fuel filter base (6) and filter (7) clear of the aftercooler housing.
1/6
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 7. Remove bolt (9) and washer that hold the pipe in the turbocharger.
8. Remove bolts (12), nuts and washer. Remove cover (10) and tube from the aftercooler cover.
9. Remove pipe (11) and adapter (8) from the engine as a unit.
10. Remove bolts (13). Remove elbow (14) from the end of the aftercooler housing and the elbow.
11. Remove adapters (15) and (16) from the aftercooler core.
12. Remove bolts (17). Remove elbow (18) from the opposite end of the aftercooler housing.
13. Remove adapters (19) and (20) from the aftercooler core.
2/6
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 14. Remove bolts (22) that hold the cover to the housing. Remove cover (21).
15. Remove aftercooler core (23) from the housing.
16. Remove bolts (25) that hold the aftercooler housing to the cylinder head. Remove aftercooler
housing (24).
Install Aftercooler (Direct Injection)
1. Check all O-ring seals for wear or damage. If necessary, make a replacement. Put a small
amount of clean SAE 30 oil on the O-ring seals before assembly.
2. Install aftercooler housing (1) on the cylinder head.
3/6
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 3. Install gasket (3) on the housing. Install aftercooler core (2) in the housing.
4. Install gasket (5) on the aftercooler core. Install cover (4) on the housing.
5. Install adapters (6) and (7) in the aftercooler core.
6. Install elbow (8) on the housing and elbow.
4/6
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 7. Install adapters (9) and (10) on the other end of the aftercooler core.
8. Install elbow (11) on the housing and elbow.
9. Check O-ring seals (14) for wear or damage. If necessary, make a replacement. Put clean SAE
30 oil on the O-ring seals.
10. Put pipe (12) and adapter (13) in position on the turbocharger and aftercooler housing. Install
the bolt and washer in the turbocharger.
11. Put the cover and tube in position on the housing. Install the bolts, nuts and washer that hold
the adapter and cover to the aftercooler housing.
12. Put fuel filter base (15) and fuel filter (16) in position on the aftercooler cover. Install the bolts
and spacers that hold it.
5/6
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 13. Put elbow (19) and precleaner in position on the cover and hose (18). Install the bolts and
spacers that hold the elbow to the aftercooler cover. Tighten the clamp on hose (18).
14. Connect hose (17) to the precleaner. Tighten the clamp that holds it.
15. Install the hood section over the aftercooler.
16. Fill the cooling system with coolant to the correct level. See LUBRICATION AND
MAINTENANCE GUIDE.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 11 23:52:56 UTC+0800 2019
6/6
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 245 EXCAVATOR 95V
Configuration: 245 EXCAVATOR 95V00001-00470 (MACHINE)
Disassembly and Assembly
3406 VEHICULAR ENGINE FOR 245 EXCAVATORS
Media Number -SENR7338-01 Publication Date -01/06/1979 Date Updated -12/10/2001
Air Cleaner Housing
SMCS - 1051-11; 1051-12
Remove Air Cleaner Housing
1. Loosen the clamps (4). Slide the hose off of the air cleaner housing.
2. Loosen the two rods (1) and remove the cup. Remove the primary element (3).
3. Remove the nuts (5) and the two bolts. Remove the air cleaner housing (2) and the gasket.
Install Air Cleaner Housing
1/2
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 1. Put the gasket and air cleaner housing (1) in position on the pipe. Install the nuts and two bolts
that hold the housing.
2. Install the primary element in the housing. Put the cup in position on the housing. Tighten two
rods (2) that hold it.
3. Slide the hose (3) into position on the air cleaner housing. Tighten the clamps that hold it.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 11 23:53:51 UTC+0800 2019
2/2
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 245 EXCAVATOR 95V
Configuration: 245 EXCAVATOR 95V00001-00470 (MACHINE)
Disassembly and Assembly
3406 VEHICULAR ENGINE FOR 245 EXCAVATORS
Media Number -SENR7338-01 Publication Date -01/06/1979 Date Updated -12/10/2001
Water Temperature Regulator
SMCS - 1355-11; 1355-12
Remove Water Temperature Regulator
1. Drain the coolant from the cooling system to a level below the water temperature regulator.
2. Loosen the clamps that hold hose (1) to the housing for the water temperature regulator. Slide
the hose away from the housing.
3. Remove bolts (2) that hold elbow (3) to the housing for the water temperature regulator. Turn
elbow (3) away from the housing.
4. Remove bolts (4) that hold the housing for the water temperature regulator to the head.
5. Remove housing (5). Remove water temperature regulator (6). Remove the gasket from the
housing.
6. Remove the seal from the housing.
1/2
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Install Water Temperature Regulator
1. Install the seal in the water temperature regulator housing with tooling (A). Install the seal with
the lip away from the regulator.
2. Put clean engine oil on the lip of the seal. Install a new gasket on the housing.
3. Install the water temperature regulator in the housing.
4. Install water temperature regulator housing (2) on the cylinder head. Install the bolts that hold
it.
5. Turn the elbow into position on the housing. Install the bolts that hold it to the housing.
6. Install the hose (1) on the housing and tighten the clamps that hold it.
7. Fill the cooling system to the correct level.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 11 23:54:47 UTC+0800 2019
2/2
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 245 EXCAVATOR 95V
Configuration: 245 EXCAVATOR 95V00001-00470 (MACHINE)
Disassembly and Assembly
3406 VEHICULAR ENGINE FOR 245 EXCAVATORS
Media Number -SENR7338-01 Publication Date -01/06/1979 Date Updated -12/10/2001
Water Pump
SMCS - 1306-11; 1361-15; 1361-16; 1361-12
Remove Water Pump
start by:
a) remove engine oil cooler
1. Remove the clamps that hold breather tube (1) to the valve cover and the cylinder block.
Remove breather tube (1).
2. Remove the bolts that hold elbow (2) to the water temperature regulator housing. Remove
elbow (2).
3. Disconnect heater hose (4) from the water pump.
4. Loosen the clamps that hold hose (5) to the water pump. Slide hose (5) away from the pump.
1/8
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 5. See the illustration for the correct location of the bolts that hold the water pump to the timing
gear plate. The bolts that have identification (X) only must be removed to remove the water pump.
6. Remove water pump (3). Remove the gasket from the timing gear plate.
Install Water Pump
1. Put the water pump (1) and a new gasket in position on the timing gear plate. Install the bolts
(4) that hold it in position.
2. Put clean SAE 30 oil on the O-ring seals on elbow (2). Put elbow (2) in position on the water
pump. Install the bolts that hold it to the water temperature regulator housing.
2/8
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
25. 3. Connect heater hose (5) to water pump.
4. Slide hose (6) into position on the water pump. Tighten the clamps that hold it.
5. Put breather tube (3) in position. Install the clamps that hold the breather tube to the valve cover
and cylinder block.
end by:
a) install engine oil cooler
Disassemble Water Pump
start by:
a) remove water pump
1. Remove bolts (1). Remove cover (2) from the water pump.
2. Remove O-ring seal (3) from the adapter.
3. Remove adapter (4) from the housing. Remove the O-ring seal from the outside diameter of the
adapter.
4. Remove bolt and retainer that hold the impeller on the shaft.
3/8
245 EXCAVATOR 95V00001-00470 (MACHINE)(UEG0866S - 00) - Documentation
2019/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...