Methanator Water Wash Procedures
To avoid nickel carbonyl formation, it is preferable to heat the catalyst above 400oF in nitrogen or some other CO free gas. If this is impractical and the catalyst must be heated with process gas, low pressure, high rate heating should be employed. The gas must be vented at a height and ideally flared. Care should be taken to ensure all methanator and local drains are shut.
Methanation catalysts are almost always manufactured and transported in the oxidized form, and therefore they must be reduced in the reactor to give nickel metal in order to make them active. The reduction is usually carried out in process gas and occurs by the two reactions:
Synthesis Gas and Refinery Hydrogen Applications
Support balls or more accurately, support balls and hold-down balls will at times need to be specified to our customers. Advice may also be needed opposite the usage of meshes and hold-down screens. This brief report focuses on some key aspects to consider.
1. Support Balls
2. Hold-down Balls
3. Meshes over Exit Collector & Exit Screen
4. Hold-down Screens
5. Support and Hold-down Ball Compositions and Applications
6. High Surface Area Dust Collectors
Methanator Water Wash Procedures
To avoid nickel carbonyl formation, it is preferable to heat the catalyst above 400oF in nitrogen or some other CO free gas. If this is impractical and the catalyst must be heated with process gas, low pressure, high rate heating should be employed. The gas must be vented at a height and ideally flared. Care should be taken to ensure all methanator and local drains are shut.
Methanation catalysts are almost always manufactured and transported in the oxidized form, and therefore they must be reduced in the reactor to give nickel metal in order to make them active. The reduction is usually carried out in process gas and occurs by the two reactions:
Synthesis Gas and Refinery Hydrogen Applications
Support balls or more accurately, support balls and hold-down balls will at times need to be specified to our customers. Advice may also be needed opposite the usage of meshes and hold-down screens. This brief report focuses on some key aspects to consider.
1. Support Balls
2. Hold-down Balls
3. Meshes over Exit Collector & Exit Screen
4. Hold-down Screens
5. Support and Hold-down Ball Compositions and Applications
6. High Surface Area Dust Collectors
VULCAN Series VSG-Z101 Primary Reforming
Initial Catalyst Reduction
Activating (reducing) the catalyst involves changing the nickel oxide to nickel, represented by:
NiO + H2 <==========> Ni + H2O
Natural gas is typically used as the hydrogen source. When it is, the catalyst reduction and putting the reformer on-line are accompanied in the same step.
"The raw gas produced by gasification needs to be treated before it can be used for the production of downstream products, such as hydrogen, SNG, ammonia, methanol, liquid fuels,electricity or direct reduction gas (DRI)"
There are various process routes available for obtaining the desired syngas composition, which may be a mixture of carbon monoxide and hydrogen or either pure hydrogen or carbon monoxide alone.
Hydrogen, for example, can be used in the refinery industry to achieve lighter and cleaner liquid fuels or for new applications such as fuel cells for power generation or cars.
Hydrogen-rich syngas can be produced via the "sour" CO shift process. In this case, the CO in the raw gas produced by gasification is shifted with steam to form hydrogen and carbon dioxide before the sour gas components are removed.
A number of processes are available for desulfurization and carbon dioxide removal, such as :MDEA, aMDEA, Gensorb, Selexol, Sulfinol, Rectisol and solid fixed-bed absorbents, i.e., VULCAN Systems Catalytic Absorbents.
Air / Steam Regeneration Procedure for Primary Reforming CcatalystGerard B. Hawkins
VULCAN Series VSG-Z101 Primary Reforming
Air steam regeneration procedures can be used either on start-up of a reformer after it has cooled, or can be done in the shut down process.
AIR STEAM REGENERATION ON SHUT DOWN
AIR STEAM REGENERATION ON START-UP
Pressure Relief Systems Vol 2
Causes of Relief Situations
This Volume 2 is a guide to the qualitative identification of common causes of overpressure in process equipment. It cannot be exhaustive; the process engineer and relief systems team should look for any credible situation in addition to those given in this Part which could lead to a need for pressure relief (a relief situation).
Pressure Relief Systems
BACKGROUND TO RELIEF SYSTEM DESIGN Vol.1 of 6
The Guide has been written to advise those involved in the design and engineering of pressure relief systems. It takes the user from the initial identification of potential causes of overpressure or under pressure through the process design of relief systems to the detailed mechanical design. "Hazard Studies" and quantitative hazards analysis are not described; these are seen as complementary activities. Typical users of the Guide will use some Parts in detail and others in overview.
GAS DISPERSION - A Definitive Guide to Accidental Releases of Heavy GasesGerard B. Hawkins
GAS DISPERSION - A Definitive Guide to Accidental Releases of Heavy Gases
This Process Safety Guide has been written with the aim of assisting process engineers, hazard analysts and environmental advisers in carrying out gas dispersion calculations. The Guide aims to provide assistance by:
• Improving awareness of the range of dispersion models available within GBHE, and providing guidance in choosing the most appropriate model for a particular application.
• Providing guidance to ensure that source terms and other model inputs are correctly specified, and the models are used within their range of applicability.
• Providing guidance to deal with particular topics in gas dispersion such as dense gas dispersion, complex terrain, and modeling the chemistry of oxides of nitrogen.
• Providing general background on air quality and dispersion modeling issues such as meteorology and air quality standards.
• Providing example calculations for real practical problems.
SCOPE
The gas dispersion guide contains the following Parts:
1 Fundamentals of meteorology.
2 Overview of air quality standards.
3 Comparison between different air quality models.
4 Designing a stack.
5 Dense gas dispersion.
6 Calculation of source terms.
7 Building wake effects.
8 Overview of the chemistry of the oxides of nitrogen.
9 Overview of the ADMS complex terrain module.
10 Overview of the ADMS deposition module.
11 ADMS examples.
12 Modeling odorous releases.
13 Bibliography of useful gas dispersion books and reports.
14 Glossary of gas dispersion modeling terms.
Appendix A : Modeling Wind Generation of Particulates.
APPENDIX B TABLE OF PROPERTY VALUES FOR SPECIFIC CHEMICALS
Theory of Carbon Formation in Steam Reforming
Contents
1 Introduction
2 Underpinning Theory
2.1 Conceptualization
2.2 Reforming Reactions
2.3 Carbon Formation Chemistry
2.3.1 Natural Gas
2.3.2 Carbon Formation for Naphtha Feeds
2.3.3 Carbon Gasification
2.4 Heat Transfer
3 Causes
3.1 Effects of Carbon Formation
3.2 Types of Carbon
4 What are the Effects of Carbon Formation?
4.1 Why does Carbon Formation Get Worse?
4.1.1 So what is the Next Step?
4.2 Consequences of Carbon Formation
4.3 Why does Carbon Form where it does?
4.3.1 Effect on Process Gas Temperature
4.4 Why does Carbon Formation Propagate Down the Tube?
4.4.1 Effect on Radiation on the Fluegas Side
4.5 Why does Carbon Formation propagate Up the Tube?
5 How do we Prevent Carbon Formation
5.1 The Role of Potash
5.2 Inclusion of Pre-reformer
5.3 Primary Reformer Catalyst Parameters
5.3.1 Activity
5.3.2 Heat Transfer
5.3.3 Increased Steam to Carbon Ratio
6 Steam Out
6.1 Why does increasing the Steam to Carbon Ratio Not Work?
6.2 Why does reducing the Feed Rate not help?
6.3 Fundamental Principles of Steam Outs
TABLES
1 Heat Transfer Coefficients in a Typical Reformer
2 Typical Catalyst Loading Options
FIGURES
1 Hot Bands
2 Conceptual Pellet
3 Naphtha Carbon Formation
4 Heat Transfer within an Reformer
5 Types of Carbon Formation
6 Effect of Carbon on Nickel Crystallites
7 Absorption of Heat
8 Comparison of "Base Case" v Carbon Forming Tube
9 Carbon Formation Vicious Circle
10 Temperature Profiles
11 Carbon Pinch Point
12 Carbon Formation
13 Effect on Process Gas Temperature
14 How does Carbon Propagate into an Unaffected Zone?
15 Movement of the Carbon Forming Region
16 Effect of Hot Bands on Radiative Heat Transfer
17 Effect of Potash on Carbon Formation
18 Application of a Pre-reformer
19 Effect of Activity on Carbon Formation
Calculation of an Ammonia Plant Energy Consumption: Gerard B. Hawkins
Calculation of an Ammonia Plant Energy Consumption:
Case Study: #06023300
Plant Note Book Series: PNBS-0602
CONTENTS
0 SCOPE
1 CALCULATION OF NATURAL GAS PROCESS FEED CONSUMPTION
2 CALCULATION OF NATURAL GAS PROCESS FUEL CONSUMPTION
3 CALCULATION OF NATURAL GAS CONSUMPTION FOR PILOT BURNERS OF FLARES
4 CALCULATION OF DEMIN. WATER FROM DEMIN. UNIT
5 CALCULATION OF DEMIN. WATER TO PACKAGE BOILERS
6 CALCULATION OF MP STEAM EXPORT
7 CALCULATION OF LP STEAM IMPORT
8 DETERMINATION OF ELECTRIC POWER CONSUMPTION
9 DETERMINATION OF THE TOTAL ENERGY CONSUMPTION OF THE AMMONIA PLANT ISBL
10 ADJUSTMENT OF ELECTRIC POWER CONSUMPTION FOR TEST RUN CONDITIONS
11 CALCULATION OF AMMONIA SHARE IN MP STEAM CONSUMPTION IN UTILITIES
12 CALCULATION OF AMMONIA SHARE IN ELECTRIC POWER CONSUMPTION IN UTILITIES
13 DETERMINATION OF THE TOTAL ENERGY CONSUMPTION OF THE AMMONIA PLANT OSBL
14 DETERMINATION OF THE TOTAL ENERGY CONSUMPTION OF THE AMMONIA PLANT
VULCAN Series VSG-Z101 Primary Reforming
Initial Catalyst Reduction
Activating (reducing) the catalyst involves changing the nickel oxide to nickel, represented by:
NiO + H2 <==========> Ni + H2O
Natural gas is typically used as the hydrogen source. When it is, the catalyst reduction and putting the reformer on-line are accompanied in the same step.
"The raw gas produced by gasification needs to be treated before it can be used for the production of downstream products, such as hydrogen, SNG, ammonia, methanol, liquid fuels,electricity or direct reduction gas (DRI)"
There are various process routes available for obtaining the desired syngas composition, which may be a mixture of carbon monoxide and hydrogen or either pure hydrogen or carbon monoxide alone.
Hydrogen, for example, can be used in the refinery industry to achieve lighter and cleaner liquid fuels or for new applications such as fuel cells for power generation or cars.
Hydrogen-rich syngas can be produced via the "sour" CO shift process. In this case, the CO in the raw gas produced by gasification is shifted with steam to form hydrogen and carbon dioxide before the sour gas components are removed.
A number of processes are available for desulfurization and carbon dioxide removal, such as :MDEA, aMDEA, Gensorb, Selexol, Sulfinol, Rectisol and solid fixed-bed absorbents, i.e., VULCAN Systems Catalytic Absorbents.
Air / Steam Regeneration Procedure for Primary Reforming CcatalystGerard B. Hawkins
VULCAN Series VSG-Z101 Primary Reforming
Air steam regeneration procedures can be used either on start-up of a reformer after it has cooled, or can be done in the shut down process.
AIR STEAM REGENERATION ON SHUT DOWN
AIR STEAM REGENERATION ON START-UP
Pressure Relief Systems Vol 2
Causes of Relief Situations
This Volume 2 is a guide to the qualitative identification of common causes of overpressure in process equipment. It cannot be exhaustive; the process engineer and relief systems team should look for any credible situation in addition to those given in this Part which could lead to a need for pressure relief (a relief situation).
Pressure Relief Systems
BACKGROUND TO RELIEF SYSTEM DESIGN Vol.1 of 6
The Guide has been written to advise those involved in the design and engineering of pressure relief systems. It takes the user from the initial identification of potential causes of overpressure or under pressure through the process design of relief systems to the detailed mechanical design. "Hazard Studies" and quantitative hazards analysis are not described; these are seen as complementary activities. Typical users of the Guide will use some Parts in detail and others in overview.
GAS DISPERSION - A Definitive Guide to Accidental Releases of Heavy GasesGerard B. Hawkins
GAS DISPERSION - A Definitive Guide to Accidental Releases of Heavy Gases
This Process Safety Guide has been written with the aim of assisting process engineers, hazard analysts and environmental advisers in carrying out gas dispersion calculations. The Guide aims to provide assistance by:
• Improving awareness of the range of dispersion models available within GBHE, and providing guidance in choosing the most appropriate model for a particular application.
• Providing guidance to ensure that source terms and other model inputs are correctly specified, and the models are used within their range of applicability.
• Providing guidance to deal with particular topics in gas dispersion such as dense gas dispersion, complex terrain, and modeling the chemistry of oxides of nitrogen.
• Providing general background on air quality and dispersion modeling issues such as meteorology and air quality standards.
• Providing example calculations for real practical problems.
SCOPE
The gas dispersion guide contains the following Parts:
1 Fundamentals of meteorology.
2 Overview of air quality standards.
3 Comparison between different air quality models.
4 Designing a stack.
5 Dense gas dispersion.
6 Calculation of source terms.
7 Building wake effects.
8 Overview of the chemistry of the oxides of nitrogen.
9 Overview of the ADMS complex terrain module.
10 Overview of the ADMS deposition module.
11 ADMS examples.
12 Modeling odorous releases.
13 Bibliography of useful gas dispersion books and reports.
14 Glossary of gas dispersion modeling terms.
Appendix A : Modeling Wind Generation of Particulates.
APPENDIX B TABLE OF PROPERTY VALUES FOR SPECIFIC CHEMICALS
Theory of Carbon Formation in Steam Reforming
Contents
1 Introduction
2 Underpinning Theory
2.1 Conceptualization
2.2 Reforming Reactions
2.3 Carbon Formation Chemistry
2.3.1 Natural Gas
2.3.2 Carbon Formation for Naphtha Feeds
2.3.3 Carbon Gasification
2.4 Heat Transfer
3 Causes
3.1 Effects of Carbon Formation
3.2 Types of Carbon
4 What are the Effects of Carbon Formation?
4.1 Why does Carbon Formation Get Worse?
4.1.1 So what is the Next Step?
4.2 Consequences of Carbon Formation
4.3 Why does Carbon Form where it does?
4.3.1 Effect on Process Gas Temperature
4.4 Why does Carbon Formation Propagate Down the Tube?
4.4.1 Effect on Radiation on the Fluegas Side
4.5 Why does Carbon Formation propagate Up the Tube?
5 How do we Prevent Carbon Formation
5.1 The Role of Potash
5.2 Inclusion of Pre-reformer
5.3 Primary Reformer Catalyst Parameters
5.3.1 Activity
5.3.2 Heat Transfer
5.3.3 Increased Steam to Carbon Ratio
6 Steam Out
6.1 Why does increasing the Steam to Carbon Ratio Not Work?
6.2 Why does reducing the Feed Rate not help?
6.3 Fundamental Principles of Steam Outs
TABLES
1 Heat Transfer Coefficients in a Typical Reformer
2 Typical Catalyst Loading Options
FIGURES
1 Hot Bands
2 Conceptual Pellet
3 Naphtha Carbon Formation
4 Heat Transfer within an Reformer
5 Types of Carbon Formation
6 Effect of Carbon on Nickel Crystallites
7 Absorption of Heat
8 Comparison of "Base Case" v Carbon Forming Tube
9 Carbon Formation Vicious Circle
10 Temperature Profiles
11 Carbon Pinch Point
12 Carbon Formation
13 Effect on Process Gas Temperature
14 How does Carbon Propagate into an Unaffected Zone?
15 Movement of the Carbon Forming Region
16 Effect of Hot Bands on Radiative Heat Transfer
17 Effect of Potash on Carbon Formation
18 Application of a Pre-reformer
19 Effect of Activity on Carbon Formation
Calculation of an Ammonia Plant Energy Consumption: Gerard B. Hawkins
Calculation of an Ammonia Plant Energy Consumption:
Case Study: #06023300
Plant Note Book Series: PNBS-0602
CONTENTS
0 SCOPE
1 CALCULATION OF NATURAL GAS PROCESS FEED CONSUMPTION
2 CALCULATION OF NATURAL GAS PROCESS FUEL CONSUMPTION
3 CALCULATION OF NATURAL GAS CONSUMPTION FOR PILOT BURNERS OF FLARES
4 CALCULATION OF DEMIN. WATER FROM DEMIN. UNIT
5 CALCULATION OF DEMIN. WATER TO PACKAGE BOILERS
6 CALCULATION OF MP STEAM EXPORT
7 CALCULATION OF LP STEAM IMPORT
8 DETERMINATION OF ELECTRIC POWER CONSUMPTION
9 DETERMINATION OF THE TOTAL ENERGY CONSUMPTION OF THE AMMONIA PLANT ISBL
10 ADJUSTMENT OF ELECTRIC POWER CONSUMPTION FOR TEST RUN CONDITIONS
11 CALCULATION OF AMMONIA SHARE IN MP STEAM CONSUMPTION IN UTILITIES
12 CALCULATION OF AMMONIA SHARE IN ELECTRIC POWER CONSUMPTION IN UTILITIES
13 DETERMINATION OF THE TOTAL ENERGY CONSUMPTION OF THE AMMONIA PLANT OSBL
14 DETERMINATION OF THE TOTAL ENERGY CONSUMPTION OF THE AMMONIA PLANT
Ammonia Plant Technology
Pre-Commissioning Best Practices
GBHE-APT-0102
PICKLING & PASSIVATION
CONTENTS
1 PURPOSE OF THE WORK
2 CHEMICAL CONCEPT
3 TECHNICAL CONCEPT
4 WASTES & SAFETY CONCEPT
5 TARGET RESULTS
6 THE GENERAL CLEANING SEQUENCE MANAGEMENT
6.6.1 Pre-cleaning or “Physical Cleaning
6.6.2 Pre-rinsing
6.6.3 Chemical Cleaning
6.6.4 Critical Factors in Cleaning Success
6.6.5 Rinsing
6.6.6 Inspection and Re-Cleaning, if Necessary
7 Systems to be treated by Pickling/Passivation
Ammonia Plant Technology
Pre-Commissioning Best Practices
Piping and Vessels Flushing and Cleaning Procedure
CONTENTS
1 Scope
2 Aim/purpose
3 Responsibilities
4 Procedure
4.1 Main cleaning methods
4.1.1 Mechanical cleaning
4.1.2 Cleaning with air
4.1.3 Cleaning with steam (for steam networks only)
4.1.4 Cleaning with water
4.2 Choice of the cleaning method
4.3 Cleaning preparation
4.4 Protection of the devices included in the network
4.5 Protection of devices in the vicinity of the network
4.6 Water flushing procedure
4.6.1 Specific problems of water flushing
4.6.2 Preparation for water flushing
4.6.3 Performing a water flush
4.6.4 Cleanliness criteria
4.7 Air blowing procedure
4.7.1 Specific problems of air blowing
4.7.2 Preparation for air blowing
4.7.3 Performing air blowing
4.7.4 Cleanliness checks
4.8 Steam blowing procedure
4.8.1 Specific problems of steam blowing
4.8.2 Preparation for steam blowing
4.8.3 Performing steam blowing
4.8.4 Cleanliness checks
4.9 Chemical cleaning procedure
4.9.1 Specific problems of cleaning with a chemical solution
4.9.2 Preparation for chemical cleaning
4.9.3 Performing a chemical cleaning
4.9.4 Cleanliness criteria
4.10 Re-assembly - general guideline
4.11 Preservation of flushed piping
DESIGN OF VENT GAS COLLECTION AND DESTRUCTION SYSTEMS Gerard B. Hawkins
DESIGN OF VENT GAS COLLECTION AND DESTRUCTION SYSTEMS
CONTENTS
1 INTRODUCTION
1.1 Purpose
1.2 Scope of this Guide
1.3 Use of the Guide
2 ENVIRONMENTAL ISSUES
2.1 Principal Concerns
2.2 Mechanisms for Ozone Formation
2.3 Photochemical Ozone Creation Potential
2.4 Health and Environmental Effects
2.5 Air Quality Standards for Ground Level Concentrations of Ozone, Targets for Reduction of VOC Discharges and Statutory Discharge Limits
3 VENTS REDUCTION PHILOSOPHY
3.1 Reduction at Source
3.2 End-of-pipe Treatment
4 METHODOLOGY FOR COLLECTION & ASSESSMENT OF PROCESS FLOW DATA
4.1 General
4.2 Identification of Vent Sources
4.3 Characterization of Vents
4.4 Quantification of Process Vent Flows
4.5 Component Flammability Data Collection
4.6 Identification of Operating Scenarios
4.7 Quantification of Flammability Characteristics for Combined Vents
4.8 Identification, Quantification and Assessment of Possibility of Air Ingress Routes
4.9 Tabulation of Data
4.10 Hazard Study and Risk Assessment
4.11 Note on Aqueous / Organic Wastes
4.12 Complexity of Systems
4.13 Summary
5 SAFE DESIGN OF VENT COLLECTION HEADER SYSTEMS
5.1 General
5.2 Process Design of Vent Headers
5.3 Liquid in Vent Headers
5.4 Materials of Construction
5.5 Static Electricity Hazard
5.6 Diversion Systems
5.7 Snuffing Systems
6 SAFE DESIGN OF THERMAL OXIDISERS
6.1 Introduction
6.2 Design Basis
6.3 Types of High Temperature Thermal Oxidizer
6.4 Refractories
6.5 Flue Gas Treatment
6.6 Control and Safety Systems
6.7 Project Program
6.8 Commissioning
6.9 Operational and Maintenance Management
APPENDICES
A GLOSSARY
B FLAMMABILITY
C EXAMPLE PROFORMA
D REFERENCES
DOCUMENTS REFERRED TO IN THIS PROCESS GUIDE
TABLE
1 PHOTOCHEMICAL OZONE CREATION POTENTIAL REFERENCED
TO ETHYLENE AS UNITY
FIGURES
1 SCHEMATIC OF TYPICAL VENT COLLECTION AND THERMAL OXIDIZER SYSTEM
2 TYPICAL KNOCK-OUT POT WITH LUTED DRAIN
3 SCHEMATIC OF DIVERSION SYSTEM
4 CONVENTIONAL VERTICAL THERMAL OXIDIZER
5 CONVENTIONAL OXIDIZER WITH INTEGRAL WATER SPARGER
6 THERMAL OXIDIZER WITH STAGED AIR INJECTION
7 DOWN-FIRED UNIT WITH WATER BATH QUENCH
8 FLAMELESS THERMAL OXIDATION UNIT
9 THERMAL OXIDIZER WITH REGENERATIVE HEAT RECOVERY
10 TYPICAL PROJECT PROGRAM
11 TYPICAL FLAMMABILITY DIAGRAM
12 EFFECT OF DILUTION WITH AIR
13 EFFECT OF DILUTION WITH AIR ON 100 Rm³ OF FLAMMABLE GAS
PRACTICAL GUIDE ON THE SELECTION OF PROCESS TECHNOLOGY FOR THE TREATMENT OF A...Gerard B. Hawkins
PRACTICAL GUIDE ON THE SELECTION OF PROCESS TECHNOLOGY FOR THE TREATMENT OF AQUEOUS ORGANIC EFFLUENT STREAMS
CONTENTS
0 INTRODUCTION/PURPOSE
1 SCOPE
2 FIELD OF APPLICATION
3 DEFINITIONS
3.1 IPU
3.2 AOS
3.3 BODs
3.4 COD
3.5 TOC
3.6 Toxicity
3.7 Refractory Organics/Hard COD
3.8 Heavy Metals
3.9 EA
3.10 Biological Treatment Terms
3.11 BATNEEC
3.12 BPEO
3.13 EQS/LV
3.14 IPC
3.15 VOC
3.16 F/M Ratio
3.17 MLSS
3.18 MLVSS
4 DESIGN/ECONOMIC GUIDELINES
5 EUROPEAN LEGISLATION
5.1 General
5.2 Integrated Pollution Control (IPC)
5.3 Best Available Techniques Not Entailing Excessive Costs (BATNEEC)
5.4 Best Practicable Environmental Option (BPEO)
5.5 Environmental Quality Standards(EQS)
6 IPU EXIT CONCENTRATION
7 SITE/LOCAL REQUIREMENTS
8 PROCESS SELECTION PROCEDURE
8.1 Waste Minimization Techniques (WMT)
8.2 AOS Stream Definition
8.3 Technical Check List
8.4 Preliminary Selection of Suitable Technologies
8.5 Process Sequences
8.6 Economic Evaluation
8.7 Process Selection
APPENDICES
A DIRECTIVE 76/464/EEC - LIST 1
B DIRECTIVE 76/464/EEC - LIST 2
C THE EUROPEAN COMMISSION PRIORITY CANDIDATE LIST
D THE UK RED LIST
E CURRENT VALUES FOR EUROPEAN COMMUNITY ENVIRONMENTAL QUALITY STANDARDS AND CORRESPONDING LIMIT VALUES
F ESTABLISHED TECHNOLOGIES
G EMERGING TECHNOLOGY
H PROPRIETARY/LESS COMMON TECHNOLOGIES
J COMPARATIVE COST DATA
PRACTICAL GUIDE ON THE REDUCTION OF DISCHARGES TO ATMOSPHERE OF VOLATILE ORGA...Gerard B. Hawkins
PRACTICAL GUIDE ON THE REDUCTION OF DISCHARGES TO ATMOSPHERE OF VOLATILE ORGANIC COMPOUNDS (VOCs)
FOREWORD
CONTENTS
1 INTRODUCTION
2 THE NEED FOR VOC CONTROL
3 CONTROL AT SOURCE
3.1 Choice or Solvent
3.2 Venting Arrangements
3.3 Nitrogen Blanketing
3.4 Pump Versus Pneumatic Transfer
3.5 Batch Charging
3.6 Reduction of Volumetric Flow
3.7 Stock Tank Design
4 DISCHARGE MEASUREMENT
4.1 By Inference or Calculation
4.2 Flow Monitoring Equipment
4.3 Analytical Instruments
4.4 Vent Emissions Database
5 ABATEMENT TECHNOLOGY
5.1 Available Options
5.2 Selection of Preferred Option
5.3 Condensation
5.4 Adsorption
5.5 Absorption
5.6 Thermal Incineration
5.7 Catalytic Oxidation
5.8 Biological Filtration
5.9 Combinations of Process technologies
5.10 Processes Under Development
6 GLOSSARY OF TERMS
7 REFERENCES
Appendix 1. Photochemical Ozone Creation Potentials
Appendix 2. Examples of Adsorption Preliminary Calculations
Appendix 3. Example of Thermal Incineration Heat and Mass Balance
Appendix 4. Cost Correlations
Getting the Most Out of Your Refinery Hydrogen PlantGerard B. Hawkins
Getting the Most Out of Your Refinery Hydrogen Plant
Contents
Summary
1 Introduction
2 "On-purpose" Hydrogen Production
3 Operational Aspects
4 Uprating Options on the Steam Reformer
4.1 Steam Reforming Catalysts and Tube Metallurgy
4.2 Oxygen-blown Secondary Reformer
4.3 Pre-reforming
4.4 Post-reforming
5 Downstream Units
6 Summary of Uprating Options
7 Conclusions
EMERGENCY ISOLATION OF CHEMICAL PLANTS
CONTENTS
1 Introduction
2 When should Emergency Isolation Valves be Installed
3 Emergency Isolation Valves and Associated Equipment
3.1 Installations on existing plant
3.2 Actuators
3.3 Power to close or power to open
3.4 The need for testing
3.5 Hand operated Emergency Valves
3.6 The need to stop pumps in an emergency
3.7 Location of Operating Buttons
3.8 Use of control valves for Isolation
4 Detection of Leaks and Fires
5 Precautions during Maintenance
6 Training Operators to use Emergency Isolation Valves
7 Emergency Isolation when no remotely operated valve is available
References
Glossary
Appendix I Some Fires or Serious Escapes of Flammable Gases or Liquids that could have been controlled by Emergency Isolation Valves
Appendix II Some typical Installations
Amine Gas Treating Unit - Best Practices - Troubleshooting Guide Gerard B. Hawkins
Amine Gas Treating Unit Best Practices - Troubleshooting Guide for H2S/CO2 Amine Systems
Contents
Process Capabilities for gas treating process
Typical Amine Treating
Typical Amine System Improvements
Primary Equipment Overview
Inlet Gas Knockout
Absorber
Three Phase Flash Tank
Lean/Rich Heat Exchanger
Regenerator
Filtration
Amine Reclaimer
Operating Difficulties Overview
Foaming
Failure to Meet Gas Specification
Solvent Losses
Corrosion
Typical Amine System Improvements
Degradation of Amines and Alkanolamines during Sour Gas Treating
APPENDIX
Best Practices - Troubleshooting Guide
LF Energy Webinar: Electrical Grid Modelling and Simulation Through PowSyBl -...DanBrown980551
Do you want to learn how to model and simulate an electrical network from scratch in under an hour?
Then welcome to this PowSyBl workshop, hosted by Rte, the French Transmission System Operator (TSO)!
During the webinar, you will discover the PowSyBl ecosystem as well as handle and study an electrical network through an interactive Python notebook.
PowSyBl is an open source project hosted by LF Energy, which offers a comprehensive set of features for electrical grid modelling and simulation. Among other advanced features, PowSyBl provides:
- A fully editable and extendable library for grid component modelling;
- Visualization tools to display your network;
- Grid simulation tools, such as power flows, security analyses (with or without remedial actions) and sensitivity analyses;
The framework is mostly written in Java, with a Python binding so that Python developers can access PowSyBl functionalities as well.
What you will learn during the webinar:
- For beginners: discover PowSyBl's functionalities through a quick general presentation and the notebook, without needing any expert coding skills;
- For advanced developers: master the skills to efficiently apply PowSyBl functionalities to your real-world scenarios.
Software Delivery At the Speed of AI: Inflectra Invests In AI-Powered QualityInflectra
In this insightful webinar, Inflectra explores how artificial intelligence (AI) is transforming software development and testing. Discover how AI-powered tools are revolutionizing every stage of the software development lifecycle (SDLC), from design and prototyping to testing, deployment, and monitoring.
Learn about:
• The Future of Testing: How AI is shifting testing towards verification, analysis, and higher-level skills, while reducing repetitive tasks.
• Test Automation: How AI-powered test case generation, optimization, and self-healing tests are making testing more efficient and effective.
• Visual Testing: Explore the emerging capabilities of AI in visual testing and how it's set to revolutionize UI verification.
• Inflectra's AI Solutions: See demonstrations of Inflectra's cutting-edge AI tools like the ChatGPT plugin and Azure Open AI platform, designed to streamline your testing process.
Whether you're a developer, tester, or QA professional, this webinar will give you valuable insights into how AI is shaping the future of software delivery.
Kubernetes & AI - Beauty and the Beast !?! @KCD Istanbul 2024Tobias Schneck
As AI technology is pushing into IT I was wondering myself, as an “infrastructure container kubernetes guy”, how get this fancy AI technology get managed from an infrastructure operational view? Is it possible to apply our lovely cloud native principals as well? What benefit’s both technologies could bring to each other?
Let me take this questions and provide you a short journey through existing deployment models and use cases for AI software. On practical examples, we discuss what cloud/on-premise strategy we may need for applying it to our own infrastructure to get it to work from an enterprise perspective. I want to give an overview about infrastructure requirements and technologies, what could be beneficial or limiting your AI use cases in an enterprise environment. An interactive Demo will give you some insides, what approaches I got already working for real.
Encryption in Microsoft 365 - ExpertsLive Netherlands 2024Albert Hoitingh
In this session I delve into the encryption technology used in Microsoft 365 and Microsoft Purview. Including the concepts of Customer Key and Double Key Encryption.
Connector Corner: Automate dynamic content and events by pushing a buttonDianaGray10
Here is something new! In our next Connector Corner webinar, we will demonstrate how you can use a single workflow to:
Create a campaign using Mailchimp with merge tags/fields
Send an interactive Slack channel message (using buttons)
Have the message received by managers and peers along with a test email for review
But there’s more:
In a second workflow supporting the same use case, you’ll see:
Your campaign sent to target colleagues for approval
If the “Approve” button is clicked, a Jira/Zendesk ticket is created for the marketing design team
But—if the “Reject” button is pushed, colleagues will be alerted via Slack message
Join us to learn more about this new, human-in-the-loop capability, brought to you by Integration Service connectors.
And...
Speakers:
Akshay Agnihotri, Product Manager
Charlie Greenberg, Host
JMeter webinar - integration with InfluxDB and GrafanaRTTS
Watch this recorded webinar about real-time monitoring of application performance. See how to integrate Apache JMeter, the open-source leader in performance testing, with InfluxDB, the open-source time-series database, and Grafana, the open-source analytics and visualization application.
In this webinar, we will review the benefits of leveraging InfluxDB and Grafana when executing load tests and demonstrate how these tools are used to visualize performance metrics.
Length: 30 minutes
Session Overview
-------------------------------------------
During this webinar, we will cover the following topics while demonstrating the integrations of JMeter, InfluxDB and Grafana:
- What out-of-the-box solutions are available for real-time monitoring JMeter tests?
- What are the benefits of integrating InfluxDB and Grafana into the load testing stack?
- Which features are provided by Grafana?
- Demonstration of InfluxDB and Grafana using a practice web application
To view the webinar recording, go to:
https://www.rttsweb.com/jmeter-integration-webinar
Elevating Tactical DDD Patterns Through Object CalisthenicsDorra BARTAGUIZ
After immersing yourself in the blue book and its red counterpart, attending DDD-focused conferences, and applying tactical patterns, you're left with a crucial question: How do I ensure my design is effective? Tactical patterns within Domain-Driven Design (DDD) serve as guiding principles for creating clear and manageable domain models. However, achieving success with these patterns requires additional guidance. Interestingly, we've observed that a set of constraints initially designed for training purposes remarkably aligns with effective pattern implementation, offering a more ‘mechanical’ approach. Let's explore together how Object Calisthenics can elevate the design of your tactical DDD patterns, offering concrete help for those venturing into DDD for the first time!
State of ICS and IoT Cyber Threat Landscape Report 2024 previewPrayukth K V
The IoT and OT threat landscape report has been prepared by the Threat Research Team at Sectrio using data from Sectrio, cyber threat intelligence farming facilities spread across over 85 cities around the world. In addition, Sectrio also runs AI-based advanced threat and payload engagement facilities that serve as sinks to attract and engage sophisticated threat actors, and newer malware including new variants and latent threats that are at an earlier stage of development.
The latest edition of the OT/ICS and IoT security Threat Landscape Report 2024 also covers:
State of global ICS asset and network exposure
Sectoral targets and attacks as well as the cost of ransom
Global APT activity, AI usage, actor and tactic profiles, and implications
Rise in volumes of AI-powered cyberattacks
Major cyber events in 2024
Malware and malicious payload trends
Cyberattack types and targets
Vulnerability exploit attempts on CVEs
Attacks on counties – USA
Expansion of bot farms – how, where, and why
In-depth analysis of the cyber threat landscape across North America, South America, Europe, APAC, and the Middle East
Why are attacks on smart factories rising?
Cyber risk predictions
Axis of attacks – Europe
Systemic attacks in the Middle East
Download the full report from here:
https://sectrio.com/resources/ot-threat-landscape-reports/sectrio-releases-ot-ics-and-iot-security-threat-landscape-report-2024/
DevOps and Testing slides at DASA ConnectKari Kakkonen
My and Rik Marselis slides at 30.5.2024 DASA Connect conference. We discuss about what is testing, then what is agile testing and finally what is Testing in DevOps. Finally we had lovely workshop with the participants trying to find out different ways to think about quality and testing in different parts of the DevOps infinity loop.
![Biodiesel Fuel Production 03 [Infographic]](https://image.slidesharecdn.com/biodieselfuelproduction03-130814160020-phpapp02/85/Biodiesel-Fuel-Production-03-Infographic-1-320.jpg)
