Analysis, design, and performance evaluations of an edge resonant switched capacitor cell-assisted soft-switching pwm boost dc–dc converter and its interleaved topology
This document summarizes the analysis, design, and performance evaluation of an edge-resonant switched capacitor cell-assisted soft-switching PWM boost DC-DC converter and its interleaved topology. The converter uses an edge-resonant switched capacitor cell to achieve zero-current turn-on and zero-voltage turn-off of the active switches, minimizing the reverse recovery current in the freewheeling diode. Circuit design guidelines and theoretical analysis of voltage conversion ratio are presented. Laboratory prototypes of the single converter and interleaved topology are evaluated experimentally and their performances are discussed.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
ANALYSIS, DESIGN AND IMPLEMENTATION OF ZERO-CURRENT-SWITCHING RESONANT CONVER...hunypink
This paper presents a Buck type circuit structure, the designing of ZCS resonant Buck converter and analysis of the working principles involved. The designed buck converter uses ZCS technique and the function is realized so that the power form is converted from 12V DC to 5V DC (1A). A detailed analysis of zero current switching buck converters is performed and a mathematical analysis of the mode of operation is also presented. In order to reduce the switching losses in associated with conventional converters; resonant inductor and resonant capacitor (LC resonant circuit) is applied which helps to turn on-off the switch at zero current. The dc-dc buck converter receives the energy from the input source, when the switch is turned-on. If the switch is turned-off the LC resonant circuit pumps the energy by ensuring that the current does not come to zero. During the hardware implementation Ton, Toff, duty cycle & operating frequency values were determined and thoroughly tuned through the NE555 IC circuit. As a result of this various waveforms across capacitors,inductors and load resistor were observed. A simulation study was carried out and the effectiveness of the designed converter is verified by PSpice simulation results.
Aml efficient approximate membership localization within a web based join fra...
Similar to Analysis, design, and performance evaluations of an edge resonant switched capacitor cell-assisted soft-switching pwm boost dc–dc converter and its interleaved topology
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
ANALYSIS, DESIGN AND IMPLEMENTATION OF ZERO-CURRENT-SWITCHING RESONANT CONVER...hunypink
This paper presents a Buck type circuit structure, the designing of ZCS resonant Buck converter and analysis of the working principles involved. The designed buck converter uses ZCS technique and the function is realized so that the power form is converted from 12V DC to 5V DC (1A). A detailed analysis of zero current switching buck converters is performed and a mathematical analysis of the mode of operation is also presented. In order to reduce the switching losses in associated with conventional converters; resonant inductor and resonant capacitor (LC resonant circuit) is applied which helps to turn on-off the switch at zero current. The dc-dc buck converter receives the energy from the input source, when the switch is turned-on. If the switch is turned-off the LC resonant circuit pumps the energy by ensuring that the current does not come to zero. During the hardware implementation Ton, Toff, duty cycle & operating frequency values were determined and thoroughly tuned through the NE555 IC circuit. As a result of this various waveforms across capacitors,inductors and load resistor were observed. A simulation study was carried out and the effectiveness of the designed converter is verified by PSpice simulation results.
Design of Half Bridge LLC Resonant Converter for Low Voltage Dc ApplicationsIOSRJEEE
An advanced hybrid LLC series resonant converter with united flying-capacitor cell is proposed in this paper to permit the high step-down conversion in the high input voltage applications. The in-built flyingcapacitor branch in the primary side can efficiently share out the primary switch voltage stress related with the half-bridge LLC converters. And the input voltage can be shared correspondingly and automatically between the two series half-bridge components lacking additional balance circuit or control strategies owing to the built-in flying- capacitor cell. Likewise, the inherent soft switching performance in extensive load range that exists in the LLC converters is still kept to decrease the switching losses, which ensures the high efficiency. In addition, the proposed converter can be comprehensive to reduce the switch voltage stress byemploying stacked connection. Finally, a 500∼640 Vinput 48 Voutput 1 kW prototype is built and tested to verify the efficiency of the proposed converter. The results prove that the proposed converter is an excellent candidate for the high input voltage and high step-down dc/dc conversion systems.
International Refereed Journal of Engineering and Science (IRJES)irjes
The core of the vision IRJES is to disseminate new knowledge and technology for the benefit of all, ranging from academic research and professional communities to industry professionals in a range of topics in computer science and engineering. It also provides a place for high-caliber researchers, practitioners and PhD students to present ongoing research and development in these areas.
Universal demand for power increases due to continuous development to fulfil all these demand. Resources
are used with optimization. A high efficiency and high power factor converters are the major parts of energy
transfer system. This paper present a general review on single stage forward and flyback converter topologies to get
better its performance. This is paper presents a kind general idea of increasing efficiency and power factor of single
stage forward and fly back converter.
SIMULATION ANALYSIS OF CLOSED LOOP DUAL INDUCTOR CURRENT-FED PUSH-PULL CONVER...Journal For Research
The current electronic devices require DC power source, which is taken from a battery or DC power supply. DC-DC converter is utilized to get regulated dc voltage from unregulated one. Switched mode power supply (SMPS) are commonly used in industrial applications, because of more advantages compared to linear power supply. In SMPS we have isolated and non-isolated converters, where isolated converters are frequently used, in order to get more voltage with multiple outputs. So among different isolated converters, push-pull converter is chosen for micro converter applications to obtain high voltage conversion ratio by using HF transformer, due to their better utilization of transformer. New methodology of control is implemented for making ZVS and ZCS at same time and to reduce the number of switches in the secondary side of dual inductor CFPP converter, which is a voltage doubler circuit. This becomes the solution for problem identification. Thus this converter with soft-switching reduces the switching losses.The current-fed push-pull converters are used in many applications like photo-voltaic (PV) power converters for boosting the output voltage. Push-pull converter is chosen for micro converter applications, to obtain high voltage conversion ratio by using high frequency (HF) transformer, due to their better utilization of transformer. This deals with the design of dual inductor CFPP converter, where zero voltage switching (ZVS) and zero current switching (ZCS) is achieved for the primary side of the converter by using secondary switches. Primary side switches are controlled by closed loop control topology. The secondary side is made with voltage doubler to obtain high voltage. Open loop and closed loop control of dual inductor current fed push pull converter simulation is finished by MATLAB/SIMULINK and their outcomes are analyzed.
Speed Control Of Separately Excited Dc Motor Using A High Efficiency Flyback ...IJERA Editor
This paper deals with Speed control of separately excited DC motor using flyback converter with a new non complementary active clamp control method to achieve soft switching and high efficiency for heavy motor load and light load conditions. This is quite attractive for low power application with universal ac inputs, such as external adaptors. With the proposed control technique, the energy in the leakage inductance can be fully recycled. The soft switching can be achieved for the main switch and the absorbed leakage energy is transferred to the output and input side. In the Proposed model the resistive and DC motor is connected to flyback converter and it is simulated with different nominal voltages and rated speed is controlled at different levels for the N-type active clamp flyback converter and P-type active clamp flyback converter respectively. N-type active clamp flyback converter is suitable for high speed variation applications and P-type active clamp flyback converter is suitable for low speed variation applications.
Design of an Integrated Power Factor Converter with PI Controller for Low Pow...IOSRJEEE
In this paper, an integrated power factor converter with PI controller is proposed. The circuit topology is obtained by integrating two converters namely the buck converter and a boost converter. The boost converter is normally a step up converter which obtain an unity power factor and performs low harmonics at the input. Based on the simple circuit topology and easy control the boost converter or buck-boost converter is used as power factor correctors. Similarly the buck converter regulates the dc-link voltage and provide a stable dc output voltage. To achieve unity power factor, the output voltage of both converter should be higher than the amplitude of the ac line voltage. The steady -state analysis is developed and a design is provided
GET IEEE BIG DATA,JAVA ,DOTNET,ANDROID ,NS2,MATLAB,EMBEDED AT LOW COST WITH BEST QUALITY PLEASE CONTACT BELOW NUMBER
FOR MORE INFORMATION PLEASE FIND THE BELOW DETAILS:
Nexgen Technology
No :66,4th cross,Venkata nagar,
Near SBI ATM,
Puducherry.
Email Id: praveen@nexgenproject.com
Mobile: 9791938249
Telephone: 0413-2211159
www.nexgenproject.com
GET IEEE BIG DATA,JAVA ,DOTNET,ANDROID ,NS2,MATLAB,EMBEDED AT LOW COST WITH BEST QUALITY PLEASE CONTACT BELOW NUMBER
FOR MORE INFORMATION PLEASE FIND THE BELOW DETAILS:
Nexgen Technology
No :66,4th cross,Venkata nagar,
Near SBI ATM,
Puducherry.
Email Id: praveen@nexgenproject.com
Mobile: 9791938249
Telephone: 0413-2211159
www.nexgenproject.com
Review of Step down Converter with Efficient ZVS OperationIJRST Journal
This paper presents the review of step down converter with efficient ZVS operation. The designed buck converter uses ZCS technique and the function is realized so that the power form is converted from 12V DC 5V DC (1A). A detailed analysis of zero current switching buck converters is performed and a mathematical analysis of the mode of operation is also presented. In order to reduce the switching losses in associated with conventional converters; resonant inductor and resonant capacitor (LC resonant circuit) is applied which helps to turn on-off the switch at zero current. The dc-dc buck converter receives the energy from the input source, when the switch is turned-on. The buck–buck converters have characteristics that warrant a more detailed study. The buck converters under discontinuous conduction mode /continuous conduction mode boundary.
Report On diode clamp three level inverterVinay Singh
three level diode clamp inverter. that converts any type of DC ( rectified, PV cell, battery etc.) to AC supply. we made by mosfet and ardiuno . in this ppt we present the Simulink model of a three-level inverter and the hardware reort of the inverter.
also discuss about other level inverter and there THD analysis, simulink model and detail. compression between another inverter.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Similar to Analysis, design, and performance evaluations of an edge resonant switched capacitor cell-assisted soft-switching pwm boost dc–dc converter and its interleaved topology (20)
Analysis, design, and performance evaluations of an edge resonant switched capacitor cell-assisted soft-switching pwm boost dc–dc converter and its interleaved topology
1. ANALYSIS, DESIGN, AND PERFORMANCE EVALUATIONS OF AN EDGERESONANT SWITCHED CAPACITOR CELL-ASSISTED SOFT-SWITCHING
PWM BOOST DC–DC CONVERTER AND ITS INTERLEAVED TOPOLOGY
ABSTRACT:
This paper presents a soft-switching pulsewidth modulation (PWM) non isolated boost dc-dc converter
embedding an edge-resonant switched capacitor (ER-SWC) cell and its interleaved circuit topology. The
conceptual boost dc-dc converter treated herein can achieve high-frequency zero-current soft-switching turn-on
and zero-voltage soft-switching turn-off operations in the active switches and minimization of a reverse
recovering current in the freewheeling diode under discontinuous conduction mode partially including critical
conduction mode in the input current. Those advantageous properties enable a wide range of soft-switching
operations together with a high-voltage step-up conversion ratio with a reduced current stress. Circuit design
guideline based on the soft-switching range is introduced; then, a theoretical analysis is carried out for
investigating the step-up voltage conversion ratio. For demonstrating the effectiveness of the ER-SWC softswitching PWM boost dc-dc converter and its newly developed interleaved topology, laboratory prototypes are
evaluated in experiments; then, their performances are discussed from a practical point of view.
