This study analyzes the influence of fuel type (gasoline or hydrogen) on sound levels produced by an internal combustion engine vehicle. Tests were conducted on a stationary Volkswagen Polo adapted for bi-fuel hydrogen-gasoline operation. Acoustic and psychoacoustic measurements were taken both inside and outside the vehicle when using each fuel. Results found a slight but statistically significant increase of 1.1-1.7 decibels in outside noise levels when using hydrogen compared to gasoline, mainly due to intensification of the 500 Hz band. Psychoacoustic loudness was also higher outside the vehicle by 2-4 sones when fueled by hydrogen. Differences in other psychoacoustic parameters were below just-noticeable
- Vehicles account for 22% of greenhouse gas emissions in the UK, and vehicle emissions contribute to global environmental degradation. Stricter laws and regulations have been implemented to limit carbon emissions from new vehicles.
- Vehicle manufacturers have implemented various technologies and strategies to reduce emissions, such as particulate traps for diesel engines, improved catalytic converters, hybrid engines, and alternative fuels. Emissions of nitrogen, particulate matter, and carbon dioxide have been significantly reduced.
- While progress has been made, debates continue around implementing increasingly stringent emissions standards without incentives for manufacturers. Manufacturers argue standards may increase costs and prices without proper assessment of economic impacts.
Carbon monoxide Content of Exhaust Emissions from Agricultural Tractor Engine...IJAEMSJORNAL
This study aims at contributing to the information buildup required for advocating the need for urgent reduction of environmental pollution by exhaust emissions from fossil fuel powered Engines in Nigeria. It was, concluded from the results obtained from the study that carbon monoxide content of the exhaust emissions of agricultural tractors are approximately forty nine(49) times higher than the recommended maximum level of 0.5 % vol CO (v/v) by the US Environmental Protection Agency (EPA). FIAT 70-666 contributed the largest content of 2.9 % vol of CO (v/v) while MASSEY FERGUSSON MF 375 contributed the least amount of 1.7 % vol of CO(v/v). Only the engine capacity had significant effect on the carbon monoxide content of the exhaust emissions of the agricultural tractors; the model/make selection did not significantly affect the CO content of their exhaust emissions.
This document discusses vehicle emissions and methods for controlling them. It begins by describing the main pollutants from vehicle emissions like hydrocarbons, carbon monoxide, nitrogen oxides, and particulate matter. It then discusses emission standards in countries like India and the US. The rest of the document details how catalytic converters work to reduce emissions by converting pollutants into less harmful substances through catalyzed chemical reactions. It also discusses emissions of greenhouse gases and technologies being developed to meet emission standards.
The document summarizes key points from Chapter 10 of the IPCC's Sixth Assessment Report on mitigation of climate change in the transport sector. It finds that transport is a major contributor to greenhouse gas emissions growth. Road transport accounts for the majority of transport emissions. The COVID-19 pandemic significantly reduced transport emissions in 2020 due to economic lockdowns. Widespread electrification of transport and alternative fuels like biofuels and hydrogen will be crucial to reduce emissions, though challenges remain in decarbonizing aviation and shipping. Shifting passengers to public transit and electrifying rail systems also provides opportunities for lower emissions.
Transportation is a major contributor to global greenhouse gas emissions, accounting for approximately 14% globally. Climate change from greenhouse gas emissions is a pressing issue that requires action. This paper examines two strategies for reducing transportation greenhouse gas emissions: 1) improving engine technologies and alternative fuels like electricity, biofuels, and hydrogen, and 2) implementing mobility management approaches like road pricing policies. The ultimate mix of emission reduction measures will depend on technology development and other economic, social, and political factors.
Transportation accounts for approximately 14% of global greenhouse gas emissions. Climate change is a pressing issue that must be addressed to avoid major environmental consequences. This paper examines strategies to reduce greenhouse gas emissions from the transportation sector, including improving engine and fuel technologies as well as implementing mobility management approaches. Engine technologies like hybrids and fuels like ethanol can help lower emissions, but the best results depend on developing alternatives from renewable sources. Mobility management, including road pricing and promoting low-speed transportation, has demonstrated potential to significantly decrease carbon dioxide emissions. Overall, a variety of solutions will be needed to curb the rising emissions expected from continued population and economic growth.
This document reviews the technical characteristics and environmental impacts of electric vehicles compared to internal combustion engine vehicles. It finds that electric vehicles are more energy efficient, with the converted Smart exhibiting a fourfold improvement in energy efficiency over the internal combustion version. However, literature data on vehicle emissions and energy use often underestimate real-world performance of internal combustion vehicles. Measured data from the converted Smart show electric vehicles can reduce greenhouse gas emissions by over 80% compared to an internal combustion vehicle when powered by the local electricity grid, with even greater reductions possible using renewable electricity. The life cycle carbon footprint of electric vehicle batteries varies significantly in literature sources but driving an electric vehicle over 100,000 km is calculated to reduce emissions by over 80% compared
Reducing the impact of rail transportation.WaseemAhmad186
The document summarizes the environmental impact of different types of rail transportation. It compares the life cycle environmental impact of two regional trains, a Swedish Intercity train and a German Regional train. The German train uses more material and energy over its lifetime per passenger kilometer traveled. Operation factors like regenerative braking can influence environmental impact, with regenerative braking being most efficient for speeds under 150 km/h. Rail transportation overall has lower environmental impact than cars or airplanes in terms of air pollution, carbon emissions, and accident risks.
- Vehicles account for 22% of greenhouse gas emissions in the UK, and vehicle emissions contribute to global environmental degradation. Stricter laws and regulations have been implemented to limit carbon emissions from new vehicles.
- Vehicle manufacturers have implemented various technologies and strategies to reduce emissions, such as particulate traps for diesel engines, improved catalytic converters, hybrid engines, and alternative fuels. Emissions of nitrogen, particulate matter, and carbon dioxide have been significantly reduced.
- While progress has been made, debates continue around implementing increasingly stringent emissions standards without incentives for manufacturers. Manufacturers argue standards may increase costs and prices without proper assessment of economic impacts.
Carbon monoxide Content of Exhaust Emissions from Agricultural Tractor Engine...IJAEMSJORNAL
This study aims at contributing to the information buildup required for advocating the need for urgent reduction of environmental pollution by exhaust emissions from fossil fuel powered Engines in Nigeria. It was, concluded from the results obtained from the study that carbon monoxide content of the exhaust emissions of agricultural tractors are approximately forty nine(49) times higher than the recommended maximum level of 0.5 % vol CO (v/v) by the US Environmental Protection Agency (EPA). FIAT 70-666 contributed the largest content of 2.9 % vol of CO (v/v) while MASSEY FERGUSSON MF 375 contributed the least amount of 1.7 % vol of CO(v/v). Only the engine capacity had significant effect on the carbon monoxide content of the exhaust emissions of the agricultural tractors; the model/make selection did not significantly affect the CO content of their exhaust emissions.
This document discusses vehicle emissions and methods for controlling them. It begins by describing the main pollutants from vehicle emissions like hydrocarbons, carbon monoxide, nitrogen oxides, and particulate matter. It then discusses emission standards in countries like India and the US. The rest of the document details how catalytic converters work to reduce emissions by converting pollutants into less harmful substances through catalyzed chemical reactions. It also discusses emissions of greenhouse gases and technologies being developed to meet emission standards.
The document summarizes key points from Chapter 10 of the IPCC's Sixth Assessment Report on mitigation of climate change in the transport sector. It finds that transport is a major contributor to greenhouse gas emissions growth. Road transport accounts for the majority of transport emissions. The COVID-19 pandemic significantly reduced transport emissions in 2020 due to economic lockdowns. Widespread electrification of transport and alternative fuels like biofuels and hydrogen will be crucial to reduce emissions, though challenges remain in decarbonizing aviation and shipping. Shifting passengers to public transit and electrifying rail systems also provides opportunities for lower emissions.
Transportation is a major contributor to global greenhouse gas emissions, accounting for approximately 14% globally. Climate change from greenhouse gas emissions is a pressing issue that requires action. This paper examines two strategies for reducing transportation greenhouse gas emissions: 1) improving engine technologies and alternative fuels like electricity, biofuels, and hydrogen, and 2) implementing mobility management approaches like road pricing policies. The ultimate mix of emission reduction measures will depend on technology development and other economic, social, and political factors.
Transportation accounts for approximately 14% of global greenhouse gas emissions. Climate change is a pressing issue that must be addressed to avoid major environmental consequences. This paper examines strategies to reduce greenhouse gas emissions from the transportation sector, including improving engine and fuel technologies as well as implementing mobility management approaches. Engine technologies like hybrids and fuels like ethanol can help lower emissions, but the best results depend on developing alternatives from renewable sources. Mobility management, including road pricing and promoting low-speed transportation, has demonstrated potential to significantly decrease carbon dioxide emissions. Overall, a variety of solutions will be needed to curb the rising emissions expected from continued population and economic growth.
This document reviews the technical characteristics and environmental impacts of electric vehicles compared to internal combustion engine vehicles. It finds that electric vehicles are more energy efficient, with the converted Smart exhibiting a fourfold improvement in energy efficiency over the internal combustion version. However, literature data on vehicle emissions and energy use often underestimate real-world performance of internal combustion vehicles. Measured data from the converted Smart show electric vehicles can reduce greenhouse gas emissions by over 80% compared to an internal combustion vehicle when powered by the local electricity grid, with even greater reductions possible using renewable electricity. The life cycle carbon footprint of electric vehicle batteries varies significantly in literature sources but driving an electric vehicle over 100,000 km is calculated to reduce emissions by over 80% compared
Reducing the impact of rail transportation.WaseemAhmad186
The document summarizes the environmental impact of different types of rail transportation. It compares the life cycle environmental impact of two regional trains, a Swedish Intercity train and a German Regional train. The German train uses more material and energy over its lifetime per passenger kilometer traveled. Operation factors like regenerative braking can influence environmental impact, with regenerative braking being most efficient for speeds under 150 km/h. Rail transportation overall has lower environmental impact than cars or airplanes in terms of air pollution, carbon emissions, and accident risks.
EFFECT OF INJECTION PRESSURE ON EXHAUST EMISSIONS OF DIESEL ENGINE FUELLED WI...IAEME Publication
In the context of exhaustion of fossil fuels day by day due to heavy demand with the use of agriculture sector and transport sector, escalation of fuel prices in International Oil Market causing huge economic burden on developing countries like India and rise of pollution levels with fossil fuel, the conservation of fossil fuels has become pertinent. Gaseous fuels have many merits over liquid fuels, as the pollutants emitted by gaseous fuels are low due to clean combustion, high calorific value in comparison with liquid fuels. Vegetable oils are good substitutes for diesel, as they are renewable, comparable calorific value and cetane (measure of combustion quality) number when compared with neat diesel operation. However, the disadvantages associated with vegetable oils such as high viscosity and low volatility cause combustion problems in diesel engines. They can be rectified to some extent by converting them into biodiesel. They are many methods to induct gaseous fuels such as port injection, carburetion technique, injection of gaseous fuel at the near end of compression stroke etc. Investigations were carried out with Acetylene gas as primary fuel inducted by port injection and diesel was injected into the engine in conventional manner. Particulate matter (PM), oxides of nitrogen (NOx), carbon mono oxide (CO) levels and un-burnt hydro carbons (UBHC) are the exhaust emissions from a diesel engine. They cause health hazards, once they are inhaled in. They also cause environmental effects like Green-house effect and Global Warming. Hence control of these emissions is an immediate effect and an urgent step. The pollutants of PM, NOx, CO and UBHC were determined at full load operation of the engine with varied injection pressure and compared with diesel operation on conventional engine. The maximum induction of Acetylene gas was 35% of total mass of diesel as full load operation. Particulate emissions were determined by AVL Smoke meter, while other emissions were measured by Netel Chromatograph multi-gas analyzer at full load operation. These pollutants were drastically reduced with induction of Acetylene gas and further reduced with an increase of injection pressure.
IRJET- Value Analysis to Reduce Noise and Control Internal CombustionIRJET Journal
This document discusses methods to reduce emissions and noise pollution from internal combustion engines. It describes how uncontrolled emissions from engines can include unburned hydrocarbons, nitrogen oxides, carbon monoxide, and particulate matter. It then outlines various emission control technologies like catalytic converters and selective catalytic reduction that can convert pollutants into less harmful gases. The document also discusses noise pollution from engines and methods to control it, such as using a DB killer muffler to muffle exhaust sound levels.
THE INFLUENCE OF CETANE NUMBER AND OXYGEN CONTENT IN THE PERFORMANCE AND EMIS...IAEME Publication
Waste plastic pyrolysis oil (WPPO) and ethanol are attractive renewable energy
sources, as ethanol has a high content of oxygen. However, for this particular study,
direct blending of conventional diesel, WPPO, ethanol and 2-ethyl hexyl nitrate (EHN)
was attempted. The purpose was, firstly, to improve the combustion, ignition quality,
performance and emission characteristics of the WPPO blends. Secondly, EHN has the
potential to reduce emissions of CO, CO2, UHC, NOX and PM. Thirdly, ethanol
improves viscosity and miscibility of biodiesel blends, besides increasing the oxygen
content of WPPO. Five mixing ratios were used in the following order,
50/WPPO25/E25, 60/WPPO20/E20, 70/WPPO15/E15, 80/WPPO10/E10 and
90/WPPO5/E5 for conventional diesel (CD), WPPO and ethanol and respectively.
However, for EHN the mixing ratio was determined by the total quantity of blended fuel
and put at 0.01 %. Complete miscibility was observed with no phase separation allowed
from the blended mixtures throughout the experiment. Performance and emission
characteristics of a stationary single cylinder water-cooled diesel power generator
were evaluated. The results obtained were compared carefully to ASTM standards and
discussed using tables and graph figure curves. The conclusion was that ethanol and
EHN can be used in diesel engine power generators as an alternative fuel to help
improve cetane numbers and to increase the oxygen content without or with
modification with WPPO blends. This is due to the densities 792 kg/m3
, 963 kg/m3
, 825
kg/m3 for WPPO, ethanol and EHN respectively, which are close to CD fuel at 845
kg/m3
. The addition of EHN, reduced emissions and improved engine performance so
that it equalled that of CD fuel
Study and Experimentation on Reduction of Emission in Diesel EngineIRJET Journal
- The document presents a study on reducing diesel engine emissions through oxygen augment combustion technology.
- An experiment was conducted on a vehicle by supplying oxygen to the intake air, which reduced emissions as measured by a smoke meter. Smoke and HC-CO levels decreased with oxygen augmentation.
- While NOx emissions may increase with higher oxygen levels, overall the study found that properly implemented oxygen augmentation can effectively reduce diesel engine emissions.
A major part of the air pollution caused is due to the vehicular emission which is increasing at an alarming rate. The different types of vehicles like car, bus, truck etc. contribute a way as well as play a dominant duty in increasing air pollution. These vehicles find its running source mainly form the extracts of fossil fuels like petrol, diesel. The fuels undergo combustion to generate energy so as to support the vehicle for duty. The incomplete combustion of the fuels in the engine paves a way for production of products like the carbon monoxide, hydrocarbons and particulate matters. A high emission level is therefore a proved result. For the purpose of forcing the fuel to have efficient combustion and for reduction of the emission levels for reducing air pollution a wide range of processes are applicable. These include improvising engine design, fuel pre-treatment etc. Among these wide ranges of options available catalytic converter is found to be a better way for establishing an efficient combustion in the controller engine of the vehicle. Usage of noble group metal is an effective way for effective combustion like the platinum group metal serves way good for reducing the exhausts. With the help of secondary measures efficiency of the engine is improved as well. The techniques are still under development as because there are some limitations of the catalytic converters which are needed to be dealt with but the application of this technique has better achievement points as well.
The document discusses the current policy approach to reducing transport-related air pollution in the EU, which has largely followed a regulatory approach through product standards and rules to meet air quality standards. It notes that while effective, this approach has limitations given the significant variations in causes and effects of air pollution across different regions and cities in Europe. Economic instruments could provide more flexibility to address this differentiation. Specifically, the document examines alternatives like adjusting taxes on fuels and vehicles to better reflect their environmental performance to further internalize the costs of air pollution.
A look at how automotive emissions legislation and the drive for energy sustainability are impacting the refining industry.
Both recent - and upcoming - legislation on automobile emissions has become the major change agent within this environmental arena. As with all legislation, regulation around emissions levels the playing field for all stakeholders in the automotive industry, effectively ensuring a competitive business climate. All participants must adjust their operations to comply with the latest regulations, leaving no-one at a competitive disadvantage.
Russell Bolton Assignment 3 discusses vehicle pollution and control over the next 20 years. It begins by introducing the serious problem of pollution from vehicles which relies on combustion engines. It then examines the specific pollutants like CO2, NOx, carbon monoxide, and hydrocarbons that are emitted from vehicles and their negative effects. The document outlines how catalytic converters have helped reduce emissions but have limitations. It predicts that stricter emissions laws will lead to more electric vehicles in the next 20 years, though batteries still have deficiencies. The conclusion reflects on an accurate 1970s study that predicted pollution levels would double by 1990 without significant emissions reductions.
This document is a final project report on electric cars submitted for a physics course. It includes an executive summary that provides an overview of electric cars and their benefits over gas-powered cars in terms of cost savings and reducing emissions. The report also discusses the history of electric cars, how they work, electric cars in Turkey, the cost effectiveness of electric cars compared to gas-powered cars, and the advantages and disadvantages of electric cars.
Application of Hydrogen as Fuel Supplement in Internal Combustion Engines-A B...IJSRD
Faced with the ever increasing cost of conventional fossil fuels and the severe environmental pollution, researchers worldwide are working to cost effectively improve internal combustion engines fuel economy and emission characteristics. Recently, use of hydrogen or hydrogen-rich gas as fuel supplement for SI and CI engines is considered to be one of the potential solutions to these problems. Hydrogen has many excellent combustion properties that can be used for improving hydrocarbon combustion and emissions performance of both SI and CI engines. This article presents a brief review on the recent progress in the application of hydrogen as a fuel additive to improve the efficiencies and emissions of modern IC engines.
Alternative Fuel Public Transport BusesIJERD Editor
The paper objective is to develop an analytical framework that will give us more insight into the
trends in emissions standards as well as technology development, and eventually translate these insights into a
sound investment decision making strategy. Public transport buses are high usage vehicles that operate in
heavily congested areas where air quality improvements and reductions in public exposure to harmful air
contaminants are critical. As such, they are good candidates for achieving both near-term and long-term
emission reductions. Cleaner and less polluting public transport buses based on alternative fuels are of
paramount importance if cities are to attain their ambitious emissions reduction targets. Decision making for the
investment in alternative fuel buses is dependent on future technological development and emissions standards,
and it is difficult, given the uncertainty in regards to both these factors.
Ammonia (nh3) as a carbon free fuel uoit vezina white paper hydrofuelSteve Wittrig
This document discusses ammonia as a potential carbon-free fuel for transportation and power generation. It summarizes that ammonia has significant potential as an alternative fuel since it does not emit direct greenhouse gases during combustion. Ammonia can be used in internal combustion engines, gas turbines, and fuel cells with only small modifications. It also discusses factors to consider in setting renewable fuel standards targets post-2020, such as environmental impacts, costs, production methods, and infrastructure requirements. The document analyzes the greenhouse gas reductions and costs of using ammonia compared to diesel and gasoline. It concludes that ammonia could reduce life cycle greenhouse gas emissions by 70-150 grams per kilometer traveled and has the lowest cost per unit of energy among alternative
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Electric vehicles (EVs) coupled with low-carbon electricity sources offer the potential for
reducing greenhouse gas emissions and exposure to tailpipe emissions from personal trans-
portation. In considering these benefits, it is important to address concerns of problem-
shifting. In addition, while many studies have focused on the use phase in comparing
transportation options, vehicle production is also significant when comparing conventional
and EVs.
a seminar report on multi-mode 2/4 stroke internal combustion enginehardik9343
The document summarizes a seminar presented by Mohammed Husain Esmail Masalawala on multi-mode 2/4-stroke internal combustion engines. The seminar addressed increasing demand for internal combustion engines, scarcity of fuel, and pollution issues. It explored areas of interest like power, efficiency, and emissions. It discussed engine types including suction ignition, compressed ignition, homogeneous compressed charged, hybrid, and boosted engines. The seminar proposed a concept of a multi-mode engine and discussed technological requirements, results, implementation areas, and concluded with highlighting the need for more efficient engines.
The document discusses hydrogen as a potential source of propulsion for aircraft. It begins with an introduction covering why hydrogen is being considered, its technological aspects, and advantages. Next, the advantages of hydrogen are presented in more detail. This is followed by a section on the environmental impacts, regulations, and legislative drives regarding hydrogen fuel. The document concludes by acknowledging limitations but arguing that hydrogen propulsion has the potential to be part of future aircraft technologies, especially for commuter, regional, and short-to-medium range flights over the next 10-15 years.
This document discusses a survey conducted on the effects of vehicle emissions on human health in Chidambaram town, India. The survey investigated the impacts of emissions from vehicles on four major junctions in the town. Questionnaires found that most people reported health issues like sleeplessness, running nose, eye irritation, asthma, and headaches. Air samples taken at the junctions found high levels of pollutants like NOx, CO, SO2, and SPM, especially during afternoon high-traffic hours. Vehicle emissions were found to be a major contributor to air pollution in urban areas and impact public health. The study aims to assess the health effects of vehicle emissions in Chidambaram and make recommendations to reduce emissions.
This doctoral thesis investigates the performance and emissions of an automotive diesel engine fueled with biofuels. Experiments were conducted using blends of ultra low sulfur diesel with fatty acid methyl esters (FAME) and hydrotreated vegetable oil (HVO) biofuels. Results showed that a specifically adjusted engine calibration could maintain engine performance while achieving substantial emissions benefits with biofuel blends, including lower smoke and NOx emissions. Further analysis of particulate matter emissions found that standard measurement techniques may underestimate emissions, especially for biofuels, and that HVO particulate matter had a higher mutagenic effect than other fuels.
STUDYING THE EFFECT OF CAR TECHNOLOGY ON CO EMISSIONS AND BENEFITS OF UPDATIN...IAEME Publication
This research compares CO emissions of old and new technology vehicles using field test. Benefits of replacement old passenger cars with new ones are estimated. Two representative cars are considered in field tests. Three factors are considered in the comparison; speed, Revolution per minutes (RPM), and relative humidity. Using mobile vehicle emission detector, more than 1000 readings are taken for each vehicle. Analysis proves that CO emissions from old technology vehicles are much more than that from new ones.
This document discusses market-based incentives that Sweden has implemented to reduce air pollution from transport, including:
- Differentiated fuel taxes based on environmental characteristics to promote cleaner fuels.
- Differential vehicle taxes based on emission classes to stimulate sales of lower-emitting vehicles.
- An environmental tax on domestic airline emissions to induce changes to more efficient engines.
- A car scrapping charge and premium to increase the ratio of scrapped cars to new cars sold.
The measures have generally been effective in promoting cleaner fuels and vehicles in Sweden.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EFFECT OF INJECTION PRESSURE ON EXHAUST EMISSIONS OF DIESEL ENGINE FUELLED WI...IAEME Publication
In the context of exhaustion of fossil fuels day by day due to heavy demand with the use of agriculture sector and transport sector, escalation of fuel prices in International Oil Market causing huge economic burden on developing countries like India and rise of pollution levels with fossil fuel, the conservation of fossil fuels has become pertinent. Gaseous fuels have many merits over liquid fuels, as the pollutants emitted by gaseous fuels are low due to clean combustion, high calorific value in comparison with liquid fuels. Vegetable oils are good substitutes for diesel, as they are renewable, comparable calorific value and cetane (measure of combustion quality) number when compared with neat diesel operation. However, the disadvantages associated with vegetable oils such as high viscosity and low volatility cause combustion problems in diesel engines. They can be rectified to some extent by converting them into biodiesel. They are many methods to induct gaseous fuels such as port injection, carburetion technique, injection of gaseous fuel at the near end of compression stroke etc. Investigations were carried out with Acetylene gas as primary fuel inducted by port injection and diesel was injected into the engine in conventional manner. Particulate matter (PM), oxides of nitrogen (NOx), carbon mono oxide (CO) levels and un-burnt hydro carbons (UBHC) are the exhaust emissions from a diesel engine. They cause health hazards, once they are inhaled in. They also cause environmental effects like Green-house effect and Global Warming. Hence control of these emissions is an immediate effect and an urgent step. The pollutants of PM, NOx, CO and UBHC were determined at full load operation of the engine with varied injection pressure and compared with diesel operation on conventional engine. The maximum induction of Acetylene gas was 35% of total mass of diesel as full load operation. Particulate emissions were determined by AVL Smoke meter, while other emissions were measured by Netel Chromatograph multi-gas analyzer at full load operation. These pollutants were drastically reduced with induction of Acetylene gas and further reduced with an increase of injection pressure.
IRJET- Value Analysis to Reduce Noise and Control Internal CombustionIRJET Journal
This document discusses methods to reduce emissions and noise pollution from internal combustion engines. It describes how uncontrolled emissions from engines can include unburned hydrocarbons, nitrogen oxides, carbon monoxide, and particulate matter. It then outlines various emission control technologies like catalytic converters and selective catalytic reduction that can convert pollutants into less harmful gases. The document also discusses noise pollution from engines and methods to control it, such as using a DB killer muffler to muffle exhaust sound levels.
THE INFLUENCE OF CETANE NUMBER AND OXYGEN CONTENT IN THE PERFORMANCE AND EMIS...IAEME Publication
Waste plastic pyrolysis oil (WPPO) and ethanol are attractive renewable energy
sources, as ethanol has a high content of oxygen. However, for this particular study,
direct blending of conventional diesel, WPPO, ethanol and 2-ethyl hexyl nitrate (EHN)
was attempted. The purpose was, firstly, to improve the combustion, ignition quality,
performance and emission characteristics of the WPPO blends. Secondly, EHN has the
potential to reduce emissions of CO, CO2, UHC, NOX and PM. Thirdly, ethanol
improves viscosity and miscibility of biodiesel blends, besides increasing the oxygen
content of WPPO. Five mixing ratios were used in the following order,
50/WPPO25/E25, 60/WPPO20/E20, 70/WPPO15/E15, 80/WPPO10/E10 and
90/WPPO5/E5 for conventional diesel (CD), WPPO and ethanol and respectively.
However, for EHN the mixing ratio was determined by the total quantity of blended fuel
and put at 0.01 %. Complete miscibility was observed with no phase separation allowed
from the blended mixtures throughout the experiment. Performance and emission
characteristics of a stationary single cylinder water-cooled diesel power generator
were evaluated. The results obtained were compared carefully to ASTM standards and
discussed using tables and graph figure curves. The conclusion was that ethanol and
EHN can be used in diesel engine power generators as an alternative fuel to help
improve cetane numbers and to increase the oxygen content without or with
modification with WPPO blends. This is due to the densities 792 kg/m3
, 963 kg/m3
, 825
kg/m3 for WPPO, ethanol and EHN respectively, which are close to CD fuel at 845
kg/m3
. The addition of EHN, reduced emissions and improved engine performance so
that it equalled that of CD fuel
Study and Experimentation on Reduction of Emission in Diesel EngineIRJET Journal
- The document presents a study on reducing diesel engine emissions through oxygen augment combustion technology.
- An experiment was conducted on a vehicle by supplying oxygen to the intake air, which reduced emissions as measured by a smoke meter. Smoke and HC-CO levels decreased with oxygen augmentation.
- While NOx emissions may increase with higher oxygen levels, overall the study found that properly implemented oxygen augmentation can effectively reduce diesel engine emissions.
A major part of the air pollution caused is due to the vehicular emission which is increasing at an alarming rate. The different types of vehicles like car, bus, truck etc. contribute a way as well as play a dominant duty in increasing air pollution. These vehicles find its running source mainly form the extracts of fossil fuels like petrol, diesel. The fuels undergo combustion to generate energy so as to support the vehicle for duty. The incomplete combustion of the fuels in the engine paves a way for production of products like the carbon monoxide, hydrocarbons and particulate matters. A high emission level is therefore a proved result. For the purpose of forcing the fuel to have efficient combustion and for reduction of the emission levels for reducing air pollution a wide range of processes are applicable. These include improvising engine design, fuel pre-treatment etc. Among these wide ranges of options available catalytic converter is found to be a better way for establishing an efficient combustion in the controller engine of the vehicle. Usage of noble group metal is an effective way for effective combustion like the platinum group metal serves way good for reducing the exhausts. With the help of secondary measures efficiency of the engine is improved as well. The techniques are still under development as because there are some limitations of the catalytic converters which are needed to be dealt with but the application of this technique has better achievement points as well.
The document discusses the current policy approach to reducing transport-related air pollution in the EU, which has largely followed a regulatory approach through product standards and rules to meet air quality standards. It notes that while effective, this approach has limitations given the significant variations in causes and effects of air pollution across different regions and cities in Europe. Economic instruments could provide more flexibility to address this differentiation. Specifically, the document examines alternatives like adjusting taxes on fuels and vehicles to better reflect their environmental performance to further internalize the costs of air pollution.
A look at how automotive emissions legislation and the drive for energy sustainability are impacting the refining industry.
Both recent - and upcoming - legislation on automobile emissions has become the major change agent within this environmental arena. As with all legislation, regulation around emissions levels the playing field for all stakeholders in the automotive industry, effectively ensuring a competitive business climate. All participants must adjust their operations to comply with the latest regulations, leaving no-one at a competitive disadvantage.
Russell Bolton Assignment 3 discusses vehicle pollution and control over the next 20 years. It begins by introducing the serious problem of pollution from vehicles which relies on combustion engines. It then examines the specific pollutants like CO2, NOx, carbon monoxide, and hydrocarbons that are emitted from vehicles and their negative effects. The document outlines how catalytic converters have helped reduce emissions but have limitations. It predicts that stricter emissions laws will lead to more electric vehicles in the next 20 years, though batteries still have deficiencies. The conclusion reflects on an accurate 1970s study that predicted pollution levels would double by 1990 without significant emissions reductions.
This document is a final project report on electric cars submitted for a physics course. It includes an executive summary that provides an overview of electric cars and their benefits over gas-powered cars in terms of cost savings and reducing emissions. The report also discusses the history of electric cars, how they work, electric cars in Turkey, the cost effectiveness of electric cars compared to gas-powered cars, and the advantages and disadvantages of electric cars.
Application of Hydrogen as Fuel Supplement in Internal Combustion Engines-A B...IJSRD
Faced with the ever increasing cost of conventional fossil fuels and the severe environmental pollution, researchers worldwide are working to cost effectively improve internal combustion engines fuel economy and emission characteristics. Recently, use of hydrogen or hydrogen-rich gas as fuel supplement for SI and CI engines is considered to be one of the potential solutions to these problems. Hydrogen has many excellent combustion properties that can be used for improving hydrocarbon combustion and emissions performance of both SI and CI engines. This article presents a brief review on the recent progress in the application of hydrogen as a fuel additive to improve the efficiencies and emissions of modern IC engines.
Alternative Fuel Public Transport BusesIJERD Editor
The paper objective is to develop an analytical framework that will give us more insight into the
trends in emissions standards as well as technology development, and eventually translate these insights into a
sound investment decision making strategy. Public transport buses are high usage vehicles that operate in
heavily congested areas where air quality improvements and reductions in public exposure to harmful air
contaminants are critical. As such, they are good candidates for achieving both near-term and long-term
emission reductions. Cleaner and less polluting public transport buses based on alternative fuels are of
paramount importance if cities are to attain their ambitious emissions reduction targets. Decision making for the
investment in alternative fuel buses is dependent on future technological development and emissions standards,
and it is difficult, given the uncertainty in regards to both these factors.
Ammonia (nh3) as a carbon free fuel uoit vezina white paper hydrofuelSteve Wittrig
This document discusses ammonia as a potential carbon-free fuel for transportation and power generation. It summarizes that ammonia has significant potential as an alternative fuel since it does not emit direct greenhouse gases during combustion. Ammonia can be used in internal combustion engines, gas turbines, and fuel cells with only small modifications. It also discusses factors to consider in setting renewable fuel standards targets post-2020, such as environmental impacts, costs, production methods, and infrastructure requirements. The document analyzes the greenhouse gas reductions and costs of using ammonia compared to diesel and gasoline. It concludes that ammonia could reduce life cycle greenhouse gas emissions by 70-150 grams per kilometer traveled and has the lowest cost per unit of energy among alternative
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Electric vehicles (EVs) coupled with low-carbon electricity sources offer the potential for
reducing greenhouse gas emissions and exposure to tailpipe emissions from personal trans-
portation. In considering these benefits, it is important to address concerns of problem-
shifting. In addition, while many studies have focused on the use phase in comparing
transportation options, vehicle production is also significant when comparing conventional
and EVs.
a seminar report on multi-mode 2/4 stroke internal combustion enginehardik9343
The document summarizes a seminar presented by Mohammed Husain Esmail Masalawala on multi-mode 2/4-stroke internal combustion engines. The seminar addressed increasing demand for internal combustion engines, scarcity of fuel, and pollution issues. It explored areas of interest like power, efficiency, and emissions. It discussed engine types including suction ignition, compressed ignition, homogeneous compressed charged, hybrid, and boosted engines. The seminar proposed a concept of a multi-mode engine and discussed technological requirements, results, implementation areas, and concluded with highlighting the need for more efficient engines.
The document discusses hydrogen as a potential source of propulsion for aircraft. It begins with an introduction covering why hydrogen is being considered, its technological aspects, and advantages. Next, the advantages of hydrogen are presented in more detail. This is followed by a section on the environmental impacts, regulations, and legislative drives regarding hydrogen fuel. The document concludes by acknowledging limitations but arguing that hydrogen propulsion has the potential to be part of future aircraft technologies, especially for commuter, regional, and short-to-medium range flights over the next 10-15 years.
This document discusses a survey conducted on the effects of vehicle emissions on human health in Chidambaram town, India. The survey investigated the impacts of emissions from vehicles on four major junctions in the town. Questionnaires found that most people reported health issues like sleeplessness, running nose, eye irritation, asthma, and headaches. Air samples taken at the junctions found high levels of pollutants like NOx, CO, SO2, and SPM, especially during afternoon high-traffic hours. Vehicle emissions were found to be a major contributor to air pollution in urban areas and impact public health. The study aims to assess the health effects of vehicle emissions in Chidambaram and make recommendations to reduce emissions.
This doctoral thesis investigates the performance and emissions of an automotive diesel engine fueled with biofuels. Experiments were conducted using blends of ultra low sulfur diesel with fatty acid methyl esters (FAME) and hydrotreated vegetable oil (HVO) biofuels. Results showed that a specifically adjusted engine calibration could maintain engine performance while achieving substantial emissions benefits with biofuel blends, including lower smoke and NOx emissions. Further analysis of particulate matter emissions found that standard measurement techniques may underestimate emissions, especially for biofuels, and that HVO particulate matter had a higher mutagenic effect than other fuels.
STUDYING THE EFFECT OF CAR TECHNOLOGY ON CO EMISSIONS AND BENEFITS OF UPDATIN...IAEME Publication
This research compares CO emissions of old and new technology vehicles using field test. Benefits of replacement old passenger cars with new ones are estimated. Two representative cars are considered in field tests. Three factors are considered in the comparison; speed, Revolution per minutes (RPM), and relative humidity. Using mobile vehicle emission detector, more than 1000 readings are taken for each vehicle. Analysis proves that CO emissions from old technology vehicles are much more than that from new ones.
This document discusses market-based incentives that Sweden has implemented to reduce air pollution from transport, including:
- Differentiated fuel taxes based on environmental characteristics to promote cleaner fuels.
- Differential vehicle taxes based on emission classes to stimulate sales of lower-emitting vehicles.
- An environmental tax on domestic airline emissions to induce changes to more efficient engines.
- A car scrapping charge and premium to increase the ratio of scrapped cars to new cars sold.
The measures have generally been effective in promoting cleaner fuels and vehicles in Sweden.
Similar to Acoustic and psychoacoustic levels from an internal combustion engine.pdf (20)
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Fuel 317 (2022) 123505
2
research group adapted a Volkswagen (VW) Polo 1.4 originally powered
by gasoline for bi-fuel hydrogen-gasoline operation (the driver chooses
whether the engine burns gasoline or hydrogen) [9]. Another study
analyzed the propensity to suffer from abnormal combustion phenom
ena of this type of engine when fueled with hydrogen. These phenomena
were characterized using several techniques, including acoustic mea
surements [10].
Along with gas emissions, noise is also considered an important
factor in urban pollution. The population is increasingly sensitive to
noise generated by road traffic in cities. Noise pollution caused by road
traffic has been extensively investigated. The harmful effects of noise
pollution are undeniable, both at an individual physiological level [11]
and at a community social level [12–13]. The auditory and non-auditory
effects of noise on health have been reviewed by Basner at al. [14].
Among the non-auditory effects, there is growing evidence that noise
leads to annoyance, disturbs sleep and causes daytime sleepiness, and
increases the occurrence of hypertension and cardiovascular disease. It
is also worth mentioning that internal noise affects the driver’s taking-
risks behavior in aspects such as car-following distances and the
length of gap in traffic [15] as well as speed choice [16]. All this evi
dence leads to increasingly restrictive regulations on noise emissions
from individual vehicles [17–18] and from traffic infrastructures [19]. It
is likely that the effects of these regulations are already being felt in
terms of a slight decrease in noise pollution in our cities [20].
The objective of this study is to analyze the possible influence of the
type of fuel (gasoline or hydrogen) on the sound levels produced by a
vehicle with an internal combustion engine. Given both the high number
of noise sources in a vehicle and the acoustic indices that may be related
to annoyance, it is convenient to limit and specify such variables. Due to
the importance of noise generation from the point of view of the public
acceptance of a technology, in addition to the most standard indices
characterizing sound levels, psychoacoustic indices have been measured
and analyzed as well to determine the acoustic quality of the sound.
When operating a vehicle at high speeds–intercity routes–the main
sources of noise are aerodynamic and rolling noise. On the contrary,
when the vehicle is operating at low speeds–urban routes–engine noise
and noise due to structure vibration prevail over other sources. The main
components of engine noise are combustion and noise associated with
the intake and exhaust. We have focused this study on noise associated
with combustion since the main objective is to analyze the influence of
the type of fuel on the noise produced by ICEs. Therefore, the experi
mental setup was designed with the purpose of avoiding noise sources
not being related to the effect of the fuel itself, such as aerodynamic and
rolling noises, as well as noises induced by the state of the asphalt.
Tests were carried out with the aforementioned VW Polo 1.4 vehicle
when stationary to eliminate rolling and aerodynamic noise. Sound
pressure measurements were carried out both inside and outside the
vehicle. The greatest influence on sound perception inside a conven
tional car is produced by the engine [21]. Previous studies have shown
that engine sound induces different perceptual responses in people ac
cording to the different states of the motor: idling, constant speed or
acceleration [22]. Both acoustic and psychoacoustic indices were
analyzed at vehicle conditions and engine speeds that were roughly the
same, except for the type of fuel (gasoline or hydrogen).
2. Experimental setup and engine characteristics
A VW 4-cylinder 1.4 L engine was used. When fueled with gasoline, it
gave maximum brake power (MBP) and maximum brake torque (MBT)
of 59 kW at 5000 rpm and 132 N⋅m at 3800 rpm, respectively. Perfor
mance was significantly reduced (MBP of 32 kW at 5000 rpm and MBT
of 63 N⋅m at 3800 rpm) when the engine was adapted to run on H2,
mainly due to the conservative operating conditions (fuel lean opera
tion) adopted to avoid abnormal combustion issues. These aspects have
been described in detail in previous papers [5–7,9–10].
Fig. 1 shows the hydrogen feeding line fitted in the vehicle. The line
connecting the gas cylinders with the accumulator requires the
hydrogen pressure to be maintained at 9 bar. This is done by an initial
pressure regulator placed in the car trunk. Because the operating pres
sure of the hydrogen injectors must be reduced to 3 bar, a second
pressure regulator is required at the accumulator inlet. Two QRAE Plus
PGM-2020 hydrogen sensors were used for safety purposes: one in the
car trunk and the other inside the vehicle. Under normal driving con
ditions, no significant hydrogen leaks were detected and no hazardous
situations were identified. The vehicle was lifted using a scissor lift and
the tests were performed by turning the wheels freely. The following
engine speeds were considered: idling, 2000, 3000 and 4000 rpm, which
were measured at 0.1 s periods with 1 rpm accuracy, trying to keep them
constant. The engine temperature during the tests was practically
identical except at idling speed, in which case the temperature with
hydrogen was around 6 ◦
C higher than with gasoline.
As shown in Fig. 2, inside the vehicle there were an acoustic head
with two microphone channels (one in each ear) in the co-driver posi
tion, and an omnidirectional microphone located in between the two
front seats. An operator stood in front of the vehicle with two micro
phones, one in each ear. The microphones (CS-10EM Roland, electret
type, omnidirectional, with response throughout the audio area and
sensitivity of − 40 dB ref. 1 V/Pa at 1 kHz) were connected to an H4nPro
recorder, a Handy Recorder made by the ZOOM Corporation. A GRAS
40AC omnidirectional microphone was also used. They were positioned
in front of the vehicle, 1.5 m away. All sensor positions were the same
irrespective of whether the vehicle was fueled with gasoline or
hydrogen. All the tests were carried out in a very large laboratory with
no special acoustic characteristics. The study focused on the differences
between the two emissions, rather than on absolute values.
Three letters were used to refer to the recordings according to the
following code. The first letter refers to the type of fuel: G, for gasoline
and H, for hydrogen. The second one refers to the recording device: I for
the interior GRAS microphone (car inside), O for the exterior GRAS
microphone (car outside), H for the interior acoustic head, and Z for the
exterior acoustic head. The third letter identifies the channel (acoustic
head cases): L for the left channel and R for the right channel. For
example, for the experiments performed with the gasoline-fueled
vehicle:
• GI: gasoline, interior microphone GRAS
• GO: gasoline, exterior microphone GRAS
• GHL: gasoline, interior acoustic head, left channel
Nomenclature
ANOVA Analysis of Variance
CB Critical Bands
f Frequency of modulation in Equation (3).
ǵ(z) Specific loudness weighting function in Equation (2)
H2ICEs Hydrogen-fueled Internal Combustion Engines
ICEs Internal Combustion Engines
JND Just-noticeable difference
k Calibration factor in Equation (3)
L Loudness (sone)
LZT Equivalent sound level (db)
LAT Equivalent sound level as measured using the A-
weighting filter network (dbA)
Ĺ(z) Specific loudness (sone/Bark)
MBP Maximum Brake Power (kW)
MBT Maximum Brake Torque (N⋅m)
R Roughness (asper)
S Sharpness (acum)
z CB number (sone/Bark)
M. Arana et al.
3. Fuel 317 (2022) 123505
3
• GHR: gasoline, interior acoustic head, right channel
• GZL: gasoline, exterior acoustic head, left channel
• GZR: gasoline, exterior acoustic head, right channel
Changing the first letter (H instead of G) gives the same cases, but
with the car being fueled with hydrogen.
An acoustic calibration signal (94 dB) was recorded on each of the 6
channels. Recordings were analyzed using the BK Connect software,
both to evaluate acoustic sound levels and spectra, and to obtain psy
choacoustic parameters (loudness, sharpness, roughness and fluctuation
strength). The sound level analysis included: spectral power in octaves
and in 1/3 octaves from 20 Hz to 10 kHz, as well as LZT (equivalent
sound level, no-weighted) and LAT (equivalent sound level, A-weighted)
levels every 0.1 s. A stable period of 20 s of each operating speed was
selected, recording the data every 0.1 s.
3. Results and discussion
3.1. Noise levels inside the car
Fig. 3 shows the sound levels (LAT) generated at the omnidirectional
interior microphone (I) for different engine speeds with the two fuels.
Regarding noise levels, they are slightly higher with hydrogen at idling
conditions, but the engine speed is also higher with this fuel. It should be
noted that, in order to achieve stable idling conditions, a greater air
intake is required when using hydrogen, which implies a higher engine
speed compared to idling with gasoline as can be seen in the Figure. This
was accomplished through a higher opening of the throttle valve at
idling conditions when using hydrogen compared with gasoline. At
higher engine speeds, LAT obviously increases with the speed, reaching
similar values for both fuels at the rest of the engine speeds (2000, 3000
and 4000 rpm).
Fig. 4 and Fig. 5 show the sound levels at the left and right channels,
respectively, of the interior acoustic head.
As for the omnidirectional microphone, when idling, noise levels at
the channels of the acoustic head inside the car are higher with
hydrogen than with gasoline. However, no clear differences between
gasoline and hydrogen are observed at higher engine speeds. In some
instances, noise level is higher with gasoline while in others it is higher
with hydrogen. In any case, the differences are small and not significant
as judged from the results of the correlation and significance tests per
formed whose scatter diagram is shown in Fig. 6.
Fig. 1. Diagram of the hydrogen gas line assembled in the vehicle.
Fig. 2. Experimental setup inside the vehicle.
M. Arana et al.
4. Fuel 317 (2022) 123505
4
3.2. Noise levels outside the car
Fig. 7 shows the sound levels (LAT) recorded by the omnidirectional
outdoor microphone (O). A slight increase of noise is noticed at all
conditions tested when the engine is fueled with hydrogen in spite of the
engine speed being slightly higher with gasoline, except for idling con
ditions as explained before. Actually, the highest difference is observed
precisely at idling conditions. The question arises whether these differ
ences are, or not, significant; therefore, analysis and significance tests
were carried out. Raw data have been plotted on scatter plots in Fig. 8 to
induce regression lines.
An analysis of variance (ANOVA) was carried out to test the null
hypothesis of no difference in the mean noise produced by each type of
fuel. Two factors were taken into account: the first one is the outside
noise level for each type of fuel (LG and LH; noise levels with gasoline
and hydrogen, respectively). The second factor is the engine speed: R1
(idling), R2 (2000 rpm), R3 (3000 rpm), and R4 (4000 rpm). This is a
balanced analysis since the sample size is the same in all cases (ni =
200). Calculations were performed with Minitab® 19.1 (64-bit) software
[23]. Table 1 summarizes the main results of the ANOVA. As can be
seen, the influence of the type of fuel on the outside sound levels is fully
significant (p < 0.001). The same conclusion is obtained both for the
engine speed (as expected) and for the interaction between both factors
(R2
= 0.9988).
Fig. 9 shows the residual plots for the outside noise levels evidencing
that the hypothesis of normality of the data is fulfilled. Differences in the
means (which have a reduced standard deviation) are very significant (p
< 0.01). Therefore, it can be concluded that the outside noise generated
by fueling the vehicle with hydrogen is slightly higher than the noise
generated when fueling it with gasoline. The differences are statistically
significant and can be stablished between 1.1 dBA and 1.7 dBA
depending on the engine speed (above idling).
Fig. 3. Sound levels (LAT) inside (I) the car for different engine speeds (rpm) when using gasoline (G) and hydrogen (H) as fuels.
Fig. 4. Sound levels (LAT) at the left channel (L) of the internal acoustic head (H) for different engine speeds (rpm) when using gasoline (G) and hydrogen (H).
M. Arana et al.
5. Fuel 317 (2022) 123505
5
Fig. 10 shows the analysis of the outside sound (omni microphone)
by frequencies (octave bands of 250, 500 and 1000 Hz). A large increase
of the 500 Hz band at speeds of 3000 rpm (period within 40–60 s) and
4000 rpm (period above 60 s) is recorded when the vehicle is fueled with
hydrogen. Therefore, this band is the main responsible for the increased
outside noise produced when using hydrogen as fuel compared to
gasoline.
3.3. Psychoacoustic parameters
Psychoacoustic parameters such as loudness, sharpness, roughness
and fluctuation strength were also assessed in this study. The analysis
was carried out using BK Connect software with the data recorded
during 10 s periods.
The psychoacoustical Bark scale was proposed by E. Zwicker in 1961
[24] who introduced the Bark unit, in memory of H. Barkhausen, the
creator of the unit of loudness level. According to the Zwicker’s
annoyance model [25], psycho-acoustic metrics are an alternative to
express people’s feelings by subjective measures rather than objective
metrics based on acoustic energy, such as LAT, also denoted as LAeq,T.
Zwicker’s theory describes sound processing by the human hearing
system based on quantitative relations between sound stimuli and
auditory perception in terms of hearing sensations. The model is based
on the anatomy of human hearing. For complex sounds, the frequency
Fig. 5. Sound levels (LAT) at the right channel (R) of the internal acoustic head (H) for different engine speeds (rpm) when using gasoline (G) and hydrogen (H).
Fig. 6. Scatter plot of inside sound levels (micro omni) for different engine speeds (rpm) when using gasoline (G; blue symbols) and hydrogen (H; red symbols) as
fuels. (For interpretation of the references to colour in this figure legend, the reader is referred to the web version of this article.)
M. Arana et al.
6. Fuel 317 (2022) 123505
6
spectrum of psycho-acoustic metrics is built in Critical Bands (CB) [26].
A critical band refers to the frequency bandwidth of the auditory filter
created by the cochlea, the sensory hearing organ within the inner ear.
Human hearing combines the sound stimuli, which are located very
close to each other in terms of frequency, into a specific CB. When
serializing these CBs, a frequency scale is created, called the CB rate
scale that ranges from 1 (centered on 60 Hz with an 80 Hz bandwidth) to
24 (centered on 13.5 kHz with a 3.5 kHz bandwidth).
A brief description of the main psychoacoustic indices is given in
what follows. Loudness (L) is the parameter dealing with the sound
volume (intensity sensations), measured in Sones with a linear scale. It is
standardized in ISO 532B. The process used to calculate L is based on the
Specific Loudness (L’(z) or L contribution for each CB, where z identifies
the CB number), measured in Sone/Bark. The total L is the result of the
different contributions as given by Eq. (1) being Δz is the bandwidth of
each Bark.
L =
∫ 24Bark
0
L’∙dz (1)
Sharpness (S) is a value of sensory human perception of unpleas
antness in sounds that is caused by high frequency components. The
greater the proportion of high frequencies, the ‘sharper’ the sound.
Zwicker and Fastl [25] defined the unit of sharpness (Acum) as ‘a narrow
band noise one critical band wide at a center frequency of 1 kHz having a
level of 60 dB′
. However, sharpness is a metric that has not been stan
dardized yet. Sharpness can be calculated according to Eq. (2) as the first
Fig. 7. Sound levels outside (O) the car for different engine speeds (rpm) when using gasoline (G) and hydrogen (H) as fuels.
Fig. 8. Scatter plot of outside sound levels (micro omni) for different engine speeds (rpm) when using gasoline (G; blue symbols) and hydrogen (H; red symbols) as
fuels. (For interpretation of the references to colour in this figure legend, the reader is referred to the web version of this article.)
M. Arana et al.
7. Fuel 317 (2022) 123505
7
moment of the specific loudness (L′
) weighted by a function g′
(z) that
grows rapidly above 2.5 kHz.
S = 0.11∙
∫24Bark
0
L’∙g’(z)∙z∙dz
∫ 24Bark
0
L’∙dz
(2)
There are several methods, that use different weighting functions,
proposed to calculate the metric [25,27–28]. In this work, DIN 45692
method was used that is based on the Zwicker & Fastl’s method [25].
Roughness (R) is a value of sensory human perception which quan
tifies the subjective perception of rapid (from 15 to 300 Hz) amplitude
modulation of a sound. Its unit is the Asper that is defined as the
roughness produced by a 1 kHz tone of 60 dB which is 100% amplitude
modulated at 70 Hz. It has been found that 70 Hz modulation frequency
produces the highest roughness for tones above 1 kHz. For tones below
1 kHz, the roughness increases as the modulation frequency decreases.
Roughness has also been used to partially quantify sound quality in car
engine noise [29].
An amplitude modulated tone can be assimilated to a sound with a
rapidly changing loudness level. For sounds that last longer than 0.3 s,
its objective measurement and subjective perception are the same.
However, new subjective effects come into play as sound duration be
comes shorter. For short-duration sounds (e.g. 10 ms), subjective
perception doubles this duration (20 ms), which is important for rough
sounds. This means that the perceived masking depth is smaller than the
objectively measured modulation depth. Consequently, the roughness of
a sound can be evaluated from Eq. (3):
R = k∙
∫ 24Bark
0
fmod∙ΔL∙dz (3)
where k is a calibration factor, fmod is the frequency of modulation and
ΔL is the perceived masking depth. By using a specific loudness mea
surement taken every 2 ms, a value for ΔL can be calculated [30].
Jeong’s method [31] is another proposed method of calculation. Ac
cording to the Zwicker and Fastl method [25] used here k = 0.0003 and
ΔL = 20⋅log10[N(1)/N(99)], where N(1) and N(99) are the percentile (1
and 99) loudness values within each analysis bandwidth (1, 1/2, 1/
8 bark; in this case, ½ bark).
Fluctuation Strength (FS) is similar to roughness but quantifying
subjective perception of slower (up to 20 Hz) amplitude modulation of a
sound. There seems to be a much higher correlation of perceived
discomfort in mechanical and traffic noise with roughness than with
fluctuation strength [32], so results obtained for this parameter will not
be shown.
Figs. 11–13 show the results for loudness, sharpness and roughness,
respectively, obtained inside the vehicle with the omnidirectional
microphone. In what follows the Figure legends will show the initial of
Table 1
ANOVA for the noise levels (LAT) outside the car.
Source Degrees of
freedom
(DF)
Sum of
squares
(SS)
Mean
squares
(MS)
F P
Fuel 1 1664 1664.4 16871.81 0.000
Engine
speed
3 126,332 42110.6 426858.79 0.000
Fuel ×
Engine
speed
3 419 139.8 1416.71 0.000
Error 1592 157 0.1
Total 1599 128,573
Model summary
S R-sq R-sq(adj)
0.314090 0.9988 0.9988
Means
N LAT (dBA) Engine
speed
(rpm)
N LAT
(dBA)
LAT gasoline 800 73.17 1000 400 60.66
LAT
hydrogen
800 75.21 2000 400 72.70
3000 400 78.71
4000 400 84.68
Fig. 9. Outside noise levels: residual plots for normality test.
M. Arana et al.
8. Fuel 317 (2022) 123505
8
the plotted parameter, e.g. Loudness_GI will be indicated by L_GI.
The scatter plot for loudness using gasoline and hydrogen is given in
Fig. 14. The regression lines are practically identical; however, there are
small differences in the means at 3000 and 4000 rpm. Obtaining sta
tistically significant differences in the mean difference (mainly due to
the reduced dispersion of the results) does not signify that such differ
ences must be clearly distinguishable by the human ear. For the results
obtained for the outside noise levels, LAT differences were between
1.14 dBA and 1.70 dBA, except at idling (3.78 dBA). Results are
expressed to two decimal places, rather out of a mathematical custom
(and necessary precision) than by realistic auditory sensations. Based on
human perception, not only is the second decimal unnecessary, but the
first one is also doubtful. The Just Noticeable Difference (JND) of a
sound signal depends on several factors, such as whether it is
experienced in free-field or diffuse-field, if it is experienced with a pure
tone or broadband noise, etc. Of course, it also differs among people. In
experiences of acoustic perception in rooms, the JND of some parame
ters is usually within 1–2 dB [33,34]. Even the accuracy of a type I sound
level meter is between ± 2 dB from low (25 Hz) to high (10 kHz) fre
quencies [35]. In conclusion, differences of<1 dB should not be taken as
auditorily significant.
As for the psychoacoustic parameters outside the vehicle, Figs. 15–17
show the results for loudness, sharpness and roughness, respectively,
obtained with the omnidirectional microphone.
A two-factor analysis of variance (ANOVA) similar to that carried out
for the outside sound levels has been carried out for loudness. It is also a
balanced analysis though the sample size is ni = 100 (800 samples for
the four speeds and the two fuels). Table 2 summarizes the results of the
Fig. 10. Analysis in terms of octave bands at 250 Hz, 500 Hz and 1 kHz of the outside sound levels produced at different engine speeds when fueled with H2 (red
lines) and gasoline (blue lines). (For interpretation of the references to colour in this figure legend, the reader is referred to the web version of this article.)
Fig. 11. Loudness inside the car (micro omni) for different engine speeds (rpm) when using gasoline (G) and hydrogen (H) as fuels.
M. Arana et al.
9. Fuel 317 (2022) 123505
9
ANOVA. As can be seen, the influence of the type of fuel on the outside
sound levels is fully significant (p < 0.001). The same conclusion is
obtained both for the engine speed and for the interaction between both
factors. It can be seen that the difference between means is greater than
the value assigned by chance with significance greater than 99%. The
corresponding scatter plot is given in Fig. 18.
A test of significance (see Table 3) has also been performed to
analyze the homogeneity test. As shown, the difference between means
is again greater than the value assigned by chance with significance
greater than 99%. Therefore, as for the sound level, loudness is higher
when using hydrogen as fuel compared to gasoline.
In relation to the JND of the described psychoacoustic parameters,
some works report on slightly different results depending on the type of
noise used in the audio tests. For example, for earthmoving machine
noise, the JND in loudness was found around 0.8 sones and the corre
sponding figure for sharpness was found around 0.04 accums [36] even
though the JND in loudness becomes greater as the sound pressure level
of the signal increases. For refrigerator appliance noise, JND obtained
for loudness and sharpness was about 0.5 sones and 0.08 accums,
respectively [37]. Being a little more conservative and assuming JND for
most of the population (above 90% instead of 75%), it can be assumed
that JND of 1 sone and 0.08 accums are more reliable values. Regarding
roughness, most papers on the just-noticeable roughness differences had
been carried out with amplitude-modulated pure tones with a varying
degree of modulation. The JND in roughness is estimated to be about
17% [38]. However, this parameter seems to be dependent on the sound
level.
In summary, the homogeneity tests for loudness do not show sig
nificant differences in the measurements taken inside the vehicle. On the
contrary, they turn out to be greater outside (between 2 and 4 sones)
when the fuel is hydrogen. Regarding sharpness, the homogeneity test
shows differences between the means with a value equal to or less than
the JND of the parameter (0.08), so they are not considered significant;
this applies for both input and output noise levels. This can be explained
taking into account that sharpness is calculated according to Eq. (2) as
the first moment of the specific loudness (L′
) weighted by a function g′
(z)
Fig. 12. Sharpness inside the car (micro omni) for different engine speeds (rpm) when using gasoline (G) and hydrogen (H) as fuels.
Fig. 13. Roughness inside the car (micro omni) for different engine speeds (rpm) when using gasoline (G) and hydrogen (H) as fuels.
M. Arana et al.
10. Fuel 317 (2022) 123505
10
that grows rapidly above 2.5 kHz. However, differences in the spectral
levels of the noises produced by the two fuels are more pronounced at
low frequencies (see Fig. 10), being negligible at high frequencies. As for
roughness, the conclusions are similar; its value is determined by the
variations (from 15 to 300 Hz) in the amplitude modulation of the
sound. In view of the results obtained, there are not significant differ
ences among the roughness produced for both fuels. However, for inside
levels at idling speed (Fig. 13), there is a notable difference in the
roughness value, which is significant. In this case, the sound levels are
very low and the influence on the value of this parameter is more
noticeable.
According to Heywood [39], noise may be generated in vehicles by
aerodynamic effects as well as by forces resulting from the combustion
process or from mechanical excitation by rotating or reciprocating en
gine components. In this work, the origin of noise differences should be
mainly due to be the combustion process because the tests were
performed with the same engine for both fuels and with the vehicle
stopped. As for combustion noise, it is due to the in-cylinder pressure
gradient generated during combustion and there are also mechanical
contributions associated to the driven valve system and auxiliary
equipment [40]. Noise produced by the sharp increase of in-cylinder
pressure is strongly affected by the heat release rate and fuel burning
velocity, which in turn mainly depend on the fuel properties, injection
strategies and fuel–air mixture composition [41–46]. In a recent paper
by Soloiu et al. a literature review is presented on the many factors
affecting noise and vibration in ICEs [47]. In this nice reactivity
controlled compression ignition study, authors emphasize the strong
influence of the chemical properties of the fuel on those phenomena. As
a result, fuels or fuel blends that are more reactive, thus leading to
higher heat release rates and combustion pressure gradients, are also
louder [47]. On the other hand, Torregrosa et al. also found an impor
tant influence of the oxygen concentration in the intake on the noise
Fig. 14. Scatter plot of inside loudness (micro omni) for different engine speeds (rpm) when using gasoline (G; blue symbols) and hydrogen (H; red symbols) as fuels.
(For interpretation of the references to colour in this figure legend, the reader is referred to the web version of this article.)
Fig. 15. Loudness outside the car (micro omni) for different engine speeds (rpm) when using gasoline (G) and hydrogen (H) as fuels.
M. Arana et al.
11. Fuel 317 (2022) 123505
11
Fig. 16. Sharpness outside the car (micro omni) for different engine speeds (rpm) when using gasoline (G) and hydrogen (H) as fuels.
Fig. 17. Roughness outside the car (micro omni) for different engine speeds (rpm) when using gasoline (G) and hydrogen (H) as fuels.
Table 2
ANOVA for the loudness levels inside the car.
Source Degrees of freedom (DF) Sum of squares (SS) Mean squares (MS) F P
Fuel 1 1721 1721.3 1948.46 0.000
Engine speed 1 247,340 82446.8 93327.31 0.000
Fuel × Engine speed 3 129 43.0 48.67 0.000
Error 3 700 0.9
Total 792 249,890
Model summary
S R-sq R-sq(adj)
0.93990 0.9972 0.9972
Means
N Loudness (sones) Engine speed (rpm) N Loudness (sones)
Loudness gasoline 400 35.08 1000 200 14.03
Loudness hydrogen 400 38.02 2000 200 28.90
3000 200 41.24
4000 200 62.02
M. Arana et al.
12. Fuel 317 (2022) 123505
12
combustion generated by a compression-ignition engine fed with gaso
line/diesel blends [48]. In this regard, low oxygen concentrations lower
the fuel burning velocity thus reducing both the rate of pressure change
and the intensity of the resonance in the combustion chamber.
As for the results found in this work, both reactivity, as given for
example for the combustion speed, and heat release rate are significantly
higher for hydrogen than for gasoline (or isooctane) [49,50], which can
explain the higher noise level and loudness recorded outside the vehicle
when burning hydrogen. In addition, engine operation with hydrogen
under fuel lean conditions, as in our case, implies a comparatively high
concentration of oxygen in the intake, which can also contribute to
higher burning velocities and increased combustion noise.
4. Conclusions
Using a commercial vehicle with an internal combustion engine
adapted to run on both gasoline and hydrogen, an experimental setup
has been designed and used to compare the sound levels produced when
using those fuels. Both acoustic and psychoacoustic indices were
analyzed at engine idling and different speeds up to 4000 rpm. The
sound levels (LAT) inside the vehicle were practically identical with both
fuels at different operating regimes except for idling since, for it to be
stable, idling with hydrogen requires greater air intake that leads to
higher speed. Outside noise levels were slightly higher when the engine
ran on hydrogen. Average values showed increases of 3.8 dB when
idling, 1.5 dB at 2000 rpm, 1.1 dB at 3000 rpm, and 1.7 dB at 4000 rpm.
Although the differences are small they are statistically significant (p <
0.01). A frequencies analysis evidenced that the differences were mainly
due to the band of 500 Hz.
Psychoacoustic parameters have been also measured, resulting in
differences between the fuels mainly at idling conditions. At higher
speeds (2000 to 4000 rpm), differences in sharpness and roughness
values are less than the JNDs of the parameters. The homogeneity tests
for loudness parameter do not show significant differences in the mea
surements taken inside the vehicle. On the contrary, they turn out to be
superior outside (between 2 and 4 sones) when the fuel is hydrogen.
Increased noise level and loudness of hydrogen compared to gaso
line, though statistically significant, are small and do not create any
annoyance issue.
Finally, it has to be highlighted that a direct monitoring of the
combustion phenomena within the cylinders during the acoustic mea
surements could not be performed in this work. Such as study would
have been helpful to better understand the differences of noise caused
for hydrogen and gasoline in terms of their performance as fuels. This
limitation as well as the study of the contribution of the block engine
vibration to the global noise are expected to be addressed in a future
work. Another interesting aspect would be to auralizate, that is, to
model and simulate the sounds produced by the engine, and then
perform psychoacoustic tests in the laboratory to study the perceived
sound quality.
CRediT authorship contribution statement
Miguel Arana: Conceptualization, Methodology, Formal analysis,
Resources, Writing – original draft. Ricardo San Martín: Investigation,
Data curation, Formal analysis, Writing – original draft. José Carlos
Urroz: Investigation, Data curation, Methodology. Pedro M. Diéguez:
Project administration, Resources, Methodology. Luis M. Gandía:
Conceptualization, Writing – review & editing.
Fig. 18. Scatter plot of outside loudness (micro omni) for different engine speeds (rpm) when using gasoline (G; blue symbols) and hydrogen (H; red symbols) as
fuels. (For interpretation of the references to colour in this figure legend, the reader is referred to the web version of this article.)
Table 3
Homogeneity test for outside loudness (values given in sones).
Gasoline Hydrogen p < 0.01
Engine speed (rpm) n1 m1 σ1 n2 m2 σ2 m2-m1 σd 2.6⋅σd
Idling 100 12.52 0.47 100 15.54 0.63 3.02 0.08 0.20
2000 100 27.82 0.69 100 29.98 0.85 2.15 0.11 0.29
3000 100 40.07 0.95 100 42.42 1.10 2.35 0.15 0.38
4000 100 59.92 0.96 100 64.13 1.49 4.21 0.18 0.46
M. Arana et al.
13. Fuel 317 (2022) 123505
13
Declaration of Competing Interest
The authors declare that they have no known competing financial
interests or personal relationships that could have appeared to influence
the work reported in this paper.
Acknowledgements
This work has been funded by the Spanish Ministry of Economy and
Competitiveness through the R + D + I research project with reference
BIA2016-76957-C3-2-R. Luis M. Gandía thanks Banco de Santander and
Universidad Pública de Navarra (UPNA) for their support under “Pro
grama de Intensificación de la Investigación 2018” initiative.
References
[1] European Commission, “Communication from the Commission to the European
Parliament, the European Council, the Council, the European Economic and Social
Committee and the Committee of the Regions. The European Green Deal” COM
(2019) 640 final. Brussels, 11.12.2019.
[2] Directive (EU) 2018/2001 of the European Parliament and of the Council of 11
December 2018 on the promotion of the use of energy from renewable sources.
Official Journal of the European Union, 21.12.2018.
[3] ACEA, The Automobile Industry Pocket Guide 2020-2021. European Automobile
Manufacturers Association, 2020.
[4] Verhelst S, Wallner T. Hydrogen-fueled internal combustion engines. Prog Energy
Combust Sci 2009;35(6):490–527. https://doi.org/10.1016/j.pecs.2009.08.001.
[5] Sopena C, Diéguez PM, Sáinz D, Urroz JC, Guelbenzu E, Gandía LM. Conversion of
a commercial spark ignition engine to run on hydrogen: performance comparison
using hydrogen and gasoline. Int J Hydrog Energy 2010;35:1420–9. https://doi.
org/10.1016/j.ijhydene.2009.11.090.
[6] Sáinz D, Diéguez PM, Urroz JC, Sopena C, Guelbenzu E, Pérez-Ezcurdia A, et al.
Conversion of a gasoline engine-generator set to a bi-fuel (hydrogen/gasoline)
electronic fuel-injected power unit. Int J Hydrog Energy 2011;36(21):13781–92.
[7] Diéguez PM, Urroz JC, Marcelino-Sádaba S, Pérez-Ezcurdia A, Benito-Amurrio M,
Sáinz D, et al. Experimental study of the performance and emission characteristics
of an adapted commercial four-cylinder spark ignition engine running on
hydrogen–methane mixtures. Appl Energy 2014;113:1068–76. https://doi.org/
10.1016/j.apenergy.2013.08.063.
[8] Ortiz-Imedio R, Ortiz A, Urroz JC, Diéguez PM, Gorri D, Gandía LM, et al.
Comparative performance of coke oven gas, hydrogen and methane in a spark
ignition engine. Int J Hydrog Energy 2021;46(33):17572–86. https://doi.org/
10.1016/j.ijhydene.2019.12.165.
[9] Sáinz D, Diéguez PM, Sopena C, Urroz JC, Gandía LM. Conversion of a commercial
gasoline vehicle to run bi-fuel (hydrogen-gasoline). Int J Hydrog Energy 2012;37
(2):1781–9. https://doi.org/10.1016/j.ijhydene.2011.10.046.
[10] Diéguez PM, Urroz JC, Sáinz D, Machin J, Arana M, Gandía LM. Characterization of
combustion anomalies in a hydrogen-fueled 1.4 L commercial spark-ignition
engine by means of in-cylinder pressure, block-engine vibration, and acoustic
measurements. Energy Convers Manag 2018;172:67–80. https://doi.org/10.1016/
j.enconman.2018.06.115.
[11] Kryter KD. The effects of noise on man. New York: Academic Press; 2013.
[12] Arana M, García A. A social survey on the effects of environmental noise on the
residents of Pamplona, Spain. Appl Acoust 1998;53(4):245–53. https://doi.org/
10.1016/S0003-682X(97)00067-4.
[13] Guski R, Schreckenberg D, Schuemer R. WHO Environmental noise guidelines for
the European Region: a systematic review on environmental noise and annoyance.
Int J Environ Res Public Health 2017;14:1539. https://doi.org/10.3390/
ijerph14121539.
[14] Basner M, Babisch W, Davis A, Brink M, Clark C, Janssen S, et al. Auditory and non-
auditory effects of noise on health. Lancet 2014;383(9925):1325–32. https://doi.
org/10.1016/S0140-6736(13)61613-X.
[15] Horswill MS, Coster ME. The effect of vehicle characteristics on drivers’ risk-taking
behavior. Ergonomics 2002;45:85–104. https://doi.org/10.1080/
00140130110115345.
[16] Horswill MS, McKenna FP. The development, validation, and application of a
video-based technique for measuring an everyday risk-taking behaviour: drivers’
speed choice. J Appl Psychol 1999;84:977–85. https://doi.org/10.1037/0021-
9010.84.6.977.
[17] Regulation No 51 of the Economic Commission for Europe of the United Nations
(UNECE) — Uniform provisions concerning the approval of motor vehicles having
at least four wheels with regard to their sound emissions, 2018/798. Official
Journal of the European Union, 4.6.2018.
[18] Miloradović D, Glišović J, Lukić J. Regulations on road vehicle noise – trends and
future activities. Mobility Vehicle Mech 2017;43(1):57–72.
[19] The European Parliament and the Council of the European Union: “Directive 2002/
49/EC of the European Parliament and of the Council of 25 June 2002 relating to
the assessment and management of environmental noise”, L 189/12. Official
Journal of the European Union, 18.7.2002.
[20] Arana M. Are urban noise pollution levels decreasing? J Acoust Soc Am 2010;127
(4):2107–9. https://doi.org/10.1121/1.3337228.
[21] Cerrato G. Automotive sound quality – powertrain, road and wind noise. Sound Vib
2009;43:16–24.
[22] Kim TG, Lee S-K, Lee HH. Characterization and quantification of luxury sound
quality in premium-class passenger cars. P I Mech Eng D-J Aut 2009;223(3):
343–53. https://doi.org/10.1243/09544070JAUTO989.
[23] Minitab Inc., State College, PA, USA. http://www.minitab.com/.
[24] Zwicker E. Subdivision of the audible frequency range into Critical Bands
(Frequenzgruppen). J Acoust Soc Am 1961;33:248. https://doi.org/10.1121/
1.1908630.
[25] Zwicker E, Fastl H. Psychoacoustics, facts and models. New York: Springer; 1990.
[26] Gelfand SA. Hearing: an introduction to psychological and physiological acoustics.
4th ed. New York: Taylor & Francis; 2004.
[27] Bismarck G. Sharpness as an attribute of the timbre of steady state sounds. Acustica
1974;30:159–72.
[28] Aures W. Berechnungsverfahren für den sensorischen wohlklang beliebiger
schallsignale. Acta Acustica united with Acustica 1985;59:130–41.
[29] Moon S, Park S, Park D, Kim W, Hwan Yun MH, Park D. A study on affective
dimensions to engine acceleration sound quality using acoustic parameters. Appl
Sci 2019;9:604. https://doi.org/10.3390/app9030604.
[30] Widmann U, Fastl H. Calculating roughness using time-varying specific loudness
spectra. Proc - Natl Conf Noise Control Eng 1998:55–60.
[31] Jeong H. Sound quality analysis of nonstationary acoustic signals. Ph. D. Thesis. ,
Department of Mechanical Engineering, Korea Advanced Institute of Science and
Technology (KAIST); 1999.
[32] Segura-Garcia J, Felici-Castell S, Perez-Solano JJ, Cobos M, Navarro JM. Low-cost
alternatives for urban noise nuisance monitoring using wireless sensor networks.
IEEE Sens J 2015;15(2):836–44. https://doi.org/10.1109/JSEN.2014.2356342.
[33] Cox T, Davies W, Lam Y. The sensitivity of listeners to early sound field changes in
auditoria. Acta Acust United Acust 1993;79:27–41.
[34] Bradley JS, Reich R, Norcross SG. A just noticeable difference in C50 for speech.
Appl Acoust 1999;58(2):99–108. https://doi.org/10.1016/S0003-682X(98)00075-
9.
[35] IEC, IEC 61672. Electroacoustics – Sound level meters – Part 1: Specifications. Int
Electrotech Comm 2002.
[36] Pedrielli F, Carletti E, Casazza C. Just noticeable differences of loudness and
sharpness for earth moving machines. Proc - Eur Conf Noise Control 2008. https://
doi.org/10.1121/1.2933219.
[37] You J, Jeon JY. Just noticeable difference of sound quality metrics of refrigerator
noise. 19th International Congress on Acoustics. 2007.
[38] Daniel P, Weber R. Psychoacoustical roughness: implementation of an optimized
model. Acta Acust United Acust 1997;83:113–23.
[39] Heywood JB. Internal Combustion Engine Fundamentals. New York: McGraw-Hill,
Inc.; 1988.
[40] Torii Kenji. Method using multiple regression analysis to separate engine radiation
noise into the contributions of combustion noise and mechanical noise in the time
domain. SAE Int J Engines 2014;7(3):1502–13. https://doi.org/10.4271/2014-01-
1678.
[41] Arsie Ivan, Di Leo Rocco, Pianese Cesare, De Cesare Matteo. Combustion noise and
pollutants prediction for injection pattern and exhaust gas recirculation tuning in
an automotive common-rail diesel engine. Oil Gas Sci Technol - Revue d’IFP
Energies nouvelles 2015;70(1):91–109. https://doi.org/10.2516/ogst/2013212.
[42] Nguyen Tuan Anh, Mikami Masato. Effect of hydrogen addition to intake air on
combustion noise from a diesel engine. Int J Hydrog Energy 2013;38(10):4153–62.
https://doi.org/10.1016/j.ijhydene.2013.01.082.
[43] Chiatti G, Chiavola O, Palmieri F, Piolo A. Diagnostic methodology for internal
combustion diesel engines via noise radiation. Energy Convers Manage 2015;89:
34–42. https://doi.org/10.1016/j.enconman.2014.09.055.
[44] d’Ambrosio S, Ferrari A. Boot injection dynamics and parametrical analysis of boot
shaped injections in low-temperature combustion diesel engines for the
optimization of pollutant emissions and combustion noise. Energy 2017;134:
420–37. https://doi.org/10.1016/j.energy.2017.05.176.
[45] Caton JA. An introduction to thermodynamic cycle simulations for internal
combustion engines. Chichester: John Wiley & Sons; 2016.
[46] d’Ambrosio S, Ferrari A, Iemmolo D, Mittica A. Dependence of combustion noise
on engine calibration parameters by means of the response surface methodology in
passenger car diesel engines. Appl Therm Eng 2019;163:114209. https://doi.org/
10.1016/j.applthermaleng.2019.114209.
[47] Soloiu Valentin, Knowles Aliyah R, Carapia Cesar E, Moncada Jose D, Wiley Justin
T, Kilpatrick Margaret, et al. n-Butanol and oleic acid methyl ester, combustion and
NVH characteristics in reactivity controlled compression ignition. Energy 2020;
207:118183. https://doi.org/10.1016/j.energy.2020.118183.
[48] Torregrosa AJ, Broatch A, Novella R, Gomez-Soriano J, Mónico LF. Impact of
gasoline and Diesel blends on combustion noise and pollutant emissions in
Premixed Charge Compression Ignition engines. Energy 2017;137:58–68. https://
doi.org/10.1016/j.energy.2017.07.010.
[49] Caton JA. First and Second Law Analyses of a Spark-Ignition Engine Using either
Isooctane or Hydrogen: An Initial Assessment. In Procedings of ICEF2006.
ICEF2006–1509. ASME Internal Combustion Division; 2006.
[50] Glassman I, Yetter RA. Combustion. 4th Ed. Amsterdam: Academic Press-Elsevier;
2008.
M. Arana et al.