Download to read offline
#8 REYMOUS Training-plan.docx TRAINING PLAN EIM
- 1. Name: REYMOUS N.FABILLO Qualification Electrical Installation and Maintenance NC II Training Plan Trainees’ Training Requirement Training Activity/Task Mode of Training Staff Facilities/Tools and Equipment Venue Assessment Method Date and Time • Look for possible industry partner •Inquire about the possibility of deploying a trainee to that particular industry • Give proposal Letters to explain the nature of the program • Set appointment for presentation • Presentation of work-based • Conduct site visit for work- based training plan • Finalize Coordinato r for Academe- Industry Linkages (Department Head) Department Secretary Industry Supervisor Pens/ Pencils Papers Printers Computer Unit Internet ALS Community Learning Center
- 2. training plan or MOAor MOU • Present the training plan and MOA or MOU for approval • Orientation and deployment of trainees in the industry CORE 1 PERFORM ROUGHING-IN ACTIVITIES, WIRING AND CABLING WORKS FOR SINGLE-PHASE DISTRIBUTION, POWER, LIGHTING AND AUXILIARY SYSTEMS LO 1 Install electrical metallic /non- metallic (PVC conduit) 1.1 Interpreted correct drawings based on job requirements 1.2 Determined correct quantities of conduit, fittings and accessories as per job requirements 1.3 Selected tools and equipment as per job requirements 1.4 Assembled conduit ensuring that fittings are fully inserted and tightened as per job requirements 1.5 Bent conduit with bends not exceeding 90° as Dual Training System Training coordinator Industry linkage officer Instructor Rigid Steel Conduits (RSC) Intermedi ate Metallic Conduit (IMC) Electrical Metallic Tubing (EMT) Polyvinyl Chloride Pipe (PVC) Condulets and Reducers lock nut and bushing Entrance Anteco training center Observation of performance Interview Third party report
- 3. per job requirements 1.6 Installed conduit couplingsand elbows as per job requirements 1.7 Threaded conduit in line with job requirements 1.8 Followed safety procedures in line with standard operating procedures (SOPs. cap Nipple 2.5 Elbow
- 4. LO 2 Install wire waysand cable tray 2.1 Interpreted correct drawings to determine job requirements 2.2 Selected correct quantities of materials as per job requirements 2.3 Selected tools and equipment as per job requirements 2.4 Installed wire ways and cable trays as per job requirements. 2.5 Foll0wed safety procedures in line with SOPs Dual Training System Training coordinator Industry linkage officer Instructor Boxes Utility Box Junction Box Pull box/Splice box Conduit supports ( e.g. hangers ) Conduit Strap Connectors (straight and angle Electrical power tools Wire ways and cable tray Electrical Metallic conduit Anteco training center Observation of performance Interview Third party report LO 3 Install auxiliary terminal cabinet and distribution panel 3. 1 Interpreted correct drawings to determine job requirements 3.2 Selected correct quantities of materials as per job requirements 3.3 Selected tools and equipment as per job Dual Training System Training coordinator Industry linkage officer Instructor Boxes Utility Box Junction Box Pull box/Splice box Conduit supports ( e.g. hangers ) Conduit Strap Anteco training center Observation of performance Interview Third party report
- 5. requirements 3.4 Installed auxiliary terminal cabinetas per job requirements 3.5 Installed auxiliary main distribution frame as per job requirements 3.6 Followed safety procedures in line with SOPs Connectors (straight and angle Electrical power tools Wire ways and cable tray Electrical Metallic conduit
- 6. LO 4. Prepare for cablepulling and installation 4.1 Prepared necessary tools, equipment, materials and personal protective equipment (PPE) in line with job requirements. 4.2 Identified cable pulling & installation requirements and constraints from plan and site inspections per job requirements. 4.3 Set up cable lay out & installation equipment in accordance with manufacturer's and job requirements. 4.4 Made site safe and secure for cable installation. 4.5 Selected suitable protective clothing and required safety devices are used 4.6 Assessed support structure as safe for normal working conditions. Dual Training System Training coordinator Industry linkage officer Instructor Spirit level, hack saw, pipe cutter, plumb bob, pipe reamer, pipe threader, pipe bender, bolt cutter, electric drill Electrical power tools - Power drills - Portable grinder Electrical Metallic conduit Wire ways and cable tray Auxiliary terminal cabinet and distribution panel. Anteco training center Observation of performance Interview Third party report
- 7. LO 5 Perform wiring and cablinglay out 5.1 Followed safety procedures based on safety regulations PPE are identified and selected in line with safety requirements 5.2 Identified tools, equipment, pulling compound and safety requirements and obtained for the lay out and installation. 5.3 Properly Installed pulling materials and tensioned to required specifications 5.4 Secured cable permanently to support structure in accordance with standard installation procedures 5.5 Observed bending radius and loops tolerance for cable materials at all times 5.6 Followed schedule of wire cutting lists based Dual Training System Training coordinator Industry linkage officer Instructor Boxes Utility Box Junction Box Pull box/Splice box Conduit supports ( e.g. hangers ) Conduit Strap Connectors (straight and angle Electrical power tools Spirit level, hack saw, pipe cutter, plumb bob, pipe reamer, pipe threader, pipe bender, bolt cutter, electric drill Electrical power tools - Power drills - Portable grinder Electrical Metallic conduit Wire ways and cable tray Anteco training center Observation of performance Interview Third party report
- 8. on estimates, quantity andsizes to avoid wastage. 5.7 Sought further instructions if unplanned events or conditions occur 5.8 Checked quality of work is done in accordance with instructions and requirements. Auxiliary terminal cabinet and distribution panel.
- 9. LO 6 Notify completion of work 6.1Made final checks to ensure that work conforms with instructions and job requirements 6.2 Notified supervisor upon completion of work 6.3 cleaned, checked and returned tools, equipment and any surplus resources and materials to storage in accordance with established procedures 6.4 Cleaned up work area and made safe according to OHSA regulations Dual Training System Training coordinator Industry linkage officer Instructor Boxes Utility Box Junction Box Pull box/Splice box Conduit supports ( e.g. hangers ) Conduit Strap Connectors (straight and angle Electrical power tools Spirit level, hack saw, pipe cutter, plumb bob, pipe reamer, pipe threader, pipe bender, bolt cutter, electric drill Electrical power tools - Power drills - Portable grinder Electrical Metallic conduit Wire ways and cable tray Anteco training center Observation of performance Interview Third party report
- 10. CORE 2 INSTALLELECTRICAL PROTECTIVE DEVICES FOR DISTRIBUTION, POWER, LIGHTING, AUXILIARY, LIGHTNING PROTECTION AND GROUNDING SYSTEMS LO 1 Plan and prepare work 1.1 Communicated and confirmed Instructions for the preparation of the work activity to ensure clear understanding 1.2 Identified tools, equipment and PPE needed to install electrical wiring and, checked to ensure they work correctly as intended and are safe to use in accordance with established procedures 1.3 Obtained materials needed for work in accordance with established procedures Dual Training System Training coordinator Industry linkage officer Instructor Pliers Screwdrivers Wrenches Wire splicers Electrician knives Electric drill Ball hammer Working gloves Safety shoes Hard hat Anteco training center Observation of performance Interview Third party report LO 2 Install electrical protective devices 2.1 Followed safety procedures are followed in line with job requirements 2.2 Performed correct procedures for installation of electrical protective devices in line with Dual Training System Training coordinator Industry linkage officer Instructor Philippine Electrical Code Safety standards Safety switch Earth Leakage Circuit Anteco training center Observation of performance Interview Third party report
- 11. job requirements and PEC. 2.3Followed schedule of work to ensure work is completed in an agreed time, to a quality standard and with a minimum waste 2.4 Sought further instructions from a supervisor if unplanned events or conditions occur 2.5 Done on-going checks of quality of work in accordance with instructions and requirements Breaker (ELCB) Conventiona l atmospheric lightning protection Grounding system LO3 Install lighting fixture and auxiliary outlet. 3.3 Followed schedule of work to ensure work is completed in an agreed time, to a quality standard and with a minimum waste 3.4 Sought further instructions from a supervisor if unplanned events or conditions occur. 3.5 Undertaken on-going checks of quality of work in Dual Training System Training coordinator Industry linkage officer Instructor Pliers Screwdrivers Wrenches Wire splicers Electrician knives Electric drill Ball hammer Working gloves Safety shoes Hard hat Lamps Spotlights Track lights Perimeter lighting Anteco training center Observation of performance Interview Third party report
- 12. accordance with instructions and requirements. LO4 Notify completion of work. 4.1 Made final checks to ensure the work conforms with instructions and requirements 4.2 Notified supervisor upon completion of work 4.3 Cleaned, checked and returned tools, equipment and any surplus resources and materials where appropriate to storage in accordance with established procedures 4.4 Cleaned work area and made safe.4 Work area is cleaned and safe Dual Training System Training coordinator Industry linkage officer Instructor Philippine Electrical Code Safety standards Safety switch Earth Leakage Circuit Breaker (ELCB) Conventiona l atmospheric lightning protection Grounding system Anteco training center Observation of performance Interview Third party report CORE 3 INSTALL WIRING DEVICES OF FLOOR AND WALL MOUNTED OUTLETS, LIGHTING FIXTURE/SWITCHES AND AUXILLIARY OUTLETS
- 13. LO1 Select wiring devices 1.1 Readand interpreted Drawings to determine job requirements. 1.2 Identified correct type and quantity of wiring devices and consumable items in line with job requirements. 1.3 Selected tools and equipment in line with job requirements 1.4 Identified and selected correct PPE in line with safety requirements Dual Training System Training coordinator Industry linkage officer Instructor Floor outlet Ground fault current interrupting device Grounding type convenience outlet Light switches Wire nut Electrical tape rubber tape Pliers Screwdrivers Wire splicers Electrician knives Working gloves Safety shoes Hard hat Anteco training center Observation of performance Interview Third party report LO2 Install wiring devices 2.1 Followed safety procedures based on safety regulations 2.2 Performed correct procedures for installation of wiring devices in line with job requirements 2.3 Followed schedule of work Dual Training System Training coordinator Industry linkage officer Instructor Wire nut Electrical tape rubber tape Pliers Screwdrivers Wire splicers Electrician knives Working gloves Safety shoes Anteco training center Observation of performance Interview Third party report
- 14. based on agreed time,quality standard and minimum wastage 2.4 Sought further instructions if unplanned events or conditions occur 2.5 Done on-going checking of quality of work in accordance with instructions and requirements. Hard hat Philippine Electrical Code Safety standards LO3 Install lighting fixture/ switches 3.1 Followed safety procedures. 3.2 Performed correct procedures for installation of lighting fixtures/switches in line with job 3.3 Followed schedule of work to ensure work is completed in an agreed time, to a quality standard and with a minimum waste 3.4 Sought further instructions from a supervisor if unplanned events or conditions occur 3.5 Undertaken on-going checks of quality of work in accordance with Dual Training System Training coordinator Industry linkage officer Instructor Wire nut Electrical tape rubber tape Pliers Screwdrivers Wire splicers Electrician knives Working gloves Safety shoes Hard hat Lamps Spotlights Track Lights Perimeter Lighting Anteco training center Observation of performance Interview Third party report
- 15. instructions and requirements LO4 Notify completion of work 4.1Made final checks to ensure the work conforms with instructions and requirements 4.2 Notified supervisor upon completion of work 4.3 Cleaned, checked and returned tools, equipment and any surplus resources and materials where appropriate to storage in accordance with established procedures 4.4 Cleaned work area and made safe. Dual Training System Training coordinator Industry linkage officer Instructor Wire nut Electrical tape rubber tape Pliers Screwdrivers Wire splicers Electrician knives Working gloves Safety shoes Hard hat Anteco training center Observation of performance Interview Third party report Prepared by: REYMOUS N. FABILLO Reviewed and verified by: Trainer
- 16.