This document outlines the 11 steps to 3D scan and print an object: 1) A quick scan of a 10cm object is performed 2) The scanner takes pictures as it revolves around the object 3) Software is used to generate a 3D volume scan 4) The software identifies and covers holes for printing 5) Commands allow filling and editing in grid mode

1. UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
STUDENT: WALTER HECTOR GONZALES ARNAO
CLASS 9: Fab
3D scanning and academy
printing (Mar 21)
2012

2. UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
Fab
academy
FIRST STEP. is chosen in order to experience quick scan that is 10 cm high
CLASS 9: 3D scanning and printing (Mar 21)
2012

3. UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
Fab
academy
STEP TWO. scanner takes pictures in revolution, as seen in the images selected
for this purpose
2012
CLASS 9: 3D scanning and printing (Mar 21)

4. UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
Fab
academy
STEP 3. install the program to work the volume scan
CLASS 9: 3D scanning and printing (Mar 21)
2012

5. UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
Fab
academy
STEP 4. then the volume identifies areas that have holes to cover
them and that the 3D printing machine Acknowledge it without
problem
2012
CLASS 9: 3D scanning and printing (Mar 21)

6. UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
Fab
academy
STEP 5. commands that allow for the filling operation can be
displayed in grid mode of amending the rhino also 2012
CLASS 9: 3D scanning and printing (Mar 21)

7. UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
Fab
academy
STEP 6. the rhino is easier to change scale
CLASS 9: 3D scanning and printing (Mar 21) 2012

8. UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
Fab
academy
STEP 7. opens the file in the software up to prepare for printing
CLASS 9: 3D scanning and printing (Mar 21) 2012

9. UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
Fab
academy
STEP 8. volume is entered in the software modified UP! 3D
printing
2012
CLASS 9: 3D scanning and printing (Mar 21)

10. UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
Fab
academy
STEP 9. once the 3D scan is taken supercie part of the contact
and then proceeded to withdraw the burr that is in contact with
the scanned object
2012
CLASS 9: 3D scanning and printing (Mar 21)

11. UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
Fab
academy
STEP 10. appreciated that the bed volume is scanned, which
allows easy disassembly, after completion of the operation
2012
CLASS 9: 3D scanning and printing (Mar 21)

12. UNIVERSIDAD NACIONAL DE INGENIERÍA
FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
Fab
academy
STEP 11. shown in the detail photos of the impression that it is
not as accurate
2012
CLASS 9: 3D scanning and printing (Mar 21)

13. UNIVERSIDAD NACIONAL DE INGENIERÍA
Conclusions. FACULTAD DE ARQUITECTURA, URBANISMO Y ARTES
1. reproduction is not as
accurate, because the level of
detail of the original ceramic
finishes imperfect
2. volume changes were made
in the rhino scanstudio and then
to close the holes, the latter is
Fab
faster
academy
STEP 12.SE turned on the LET
CLASS 9: 3D scanning and printing (Mar 21)
2012