This document provides an overview of existing dispersion models and literature on modeling the dispersion of emissions from rooftop stacks. It summarizes key findings from previous studies on how increasing stack height and exhaust velocity can reduce pollutant concentrations at nearby receptors. However, it notes that field studies have sometimes found concentrations to be higher than predicted by models, due to factors like nearby buildings and atmospheric turbulence. The document then describes the ASHRAE geometric design method and dilution models that will be evaluated using new field data collected for this study.
The Influence of Pore Air Pressure on Slope Stability Under Various Rainfall ...coreconferences
Rainfall is the most important factor to induce landslide, of which rainfall pattern is the main influence parameter. Generally, during the analysis of slope stability under different rainfall patterns, the influence of pore water pressure in saturated zone is mostly considered, while the influence of pore air pressure in unsaturated zone is seldom analyzed from the angle of water-air coupling. Based on the theory of water-air two-phase flow, this paper calculated and simulated the variation of pore air pressure changing with the rainfall time under three typical rainfall patterns (weakened, concentrated and enhanced), and combined the slope stability analysis model of considering pore air pressure to study the influence of pore air pressure on slope stability. The results show that the influence of pore air pressure on slope stability is detrimental under the three rainfall patterns. And the response duration of the pore air pressure is the longest under the weakened rainfall pattern, the concentrated pattern is the second, and the enhanced pattern is the shortest. The influence of pore air pressure on the safety factor of slope stability is the greatest under the weakened rainfall pattern, which can easily lead to the instability of the slope. Thus, we shall take the necessary engineering measures in advance in the event of such rainfall pattern prediction.
A Computational Investigation of Flow Structure Within a Sinuous DuctIJERA Editor
In the present investigation the distribution of mean velocity are experimentally studied on three constant area
rectangular curved ducts with an aspect ratio of 2.4. First one is C-shape, second one is S-shape and third one
is a DS-shape duct. The experiment is carried out at mass averaged mean velocity of 40m/s for all the ducts.
The velocity distribution shows for C-duct, the bulk flow shifting from outer wall to the inner wall along the
flow passage and for S-duct, the bulk flow shifting from outer wall to the inner wall in the first half and from
inner wall to the outer wall in the second half along the flow passage of curved ducts are very instinct. Due to
the imbalance of centrifugal force and radial pressure gradient, secondary motions in the forms of counter
rotating vortices have been generated within both the curved duct. For DS-duct the velocity distributions shows
the Bulk of flow shifting from inner watt to outer wall in the first bend and third bend of the duct and outer wall
to inner wall in the second bend and forth bend of the duct along the flow passage is very instinct. Flow at end
of the DS-duct is purely uniform in nature due to non existence of secondary motion. The experimental results
then were numerically validated with the help of Fluent, which shows a good agreement between the
experimental and predicted results for all the ducts
The Influence of Pore Air Pressure on Slope Stability Under Various Rainfall ...coreconferences
Rainfall is the most important factor to induce landslide, of which rainfall pattern is the main influence parameter. Generally, during the analysis of slope stability under different rainfall patterns, the influence of pore water pressure in saturated zone is mostly considered, while the influence of pore air pressure in unsaturated zone is seldom analyzed from the angle of water-air coupling. Based on the theory of water-air two-phase flow, this paper calculated and simulated the variation of pore air pressure changing with the rainfall time under three typical rainfall patterns (weakened, concentrated and enhanced), and combined the slope stability analysis model of considering pore air pressure to study the influence of pore air pressure on slope stability. The results show that the influence of pore air pressure on slope stability is detrimental under the three rainfall patterns. And the response duration of the pore air pressure is the longest under the weakened rainfall pattern, the concentrated pattern is the second, and the enhanced pattern is the shortest. The influence of pore air pressure on the safety factor of slope stability is the greatest under the weakened rainfall pattern, which can easily lead to the instability of the slope. Thus, we shall take the necessary engineering measures in advance in the event of such rainfall pattern prediction.
A Computational Investigation of Flow Structure Within a Sinuous DuctIJERA Editor
In the present investigation the distribution of mean velocity are experimentally studied on three constant area
rectangular curved ducts with an aspect ratio of 2.4. First one is C-shape, second one is S-shape and third one
is a DS-shape duct. The experiment is carried out at mass averaged mean velocity of 40m/s for all the ducts.
The velocity distribution shows for C-duct, the bulk flow shifting from outer wall to the inner wall along the
flow passage and for S-duct, the bulk flow shifting from outer wall to the inner wall in the first half and from
inner wall to the outer wall in the second half along the flow passage of curved ducts are very instinct. Due to
the imbalance of centrifugal force and radial pressure gradient, secondary motions in the forms of counter
rotating vortices have been generated within both the curved duct. For DS-duct the velocity distributions shows
the Bulk of flow shifting from inner watt to outer wall in the first bend and third bend of the duct and outer wall
to inner wall in the second bend and forth bend of the duct along the flow passage is very instinct. Flow at end
of the DS-duct is purely uniform in nature due to non existence of secondary motion. The experimental results
then were numerically validated with the help of Fluent, which shows a good agreement between the
experimental and predicted results for all the ducts
Evaluation of Modelling of Flow in Fracturesidescitation
Heat-transport is important for geothermal exploration. The presence of
fractures can have a pronounced effect on groundwater and heat transfer.The inclusion of
fractures into geothermal reservoir models on different scales is often still a difficult task. A
comparison of approaches for flow in fractures has been carried out. A very simple
approach is to simulate fractures with thin but highly conductive layers, for instance by
applying the Cubic-Law. A more sophisticated approach, typically in FEM codes, is the
application of lower dimensional (1D/2D) high permeable discrete elements with specific
flow properties, following e.g. Hagen-Poiseuille or Manning-Strickler. However, such an
approach typically fails while studying only partly saturated fractures. For studying the
applicability of simplified fracture modellingapproaches a comparison with a CFD
(Computational Fluid Dynamics) solution was performed. Furthermore a DEM (Discrete
Element Method)approach has been illuminated. The various methodologies are studied by
varying roughnesses,this way studying the versatility of the approach. The sensitivity of
flow in fractures to various numerical parameters can be studied this way. A detailed
analysis of temperature and flow using Péclet and Reynolds numbers helps to quantify the
contributions of the different transfer processes.
International Journal of Computational Engineering Research(IJCER)ijceronline
International Journal of Computational Engineering Research(IJCER) is an intentional online Journal in English monthly publishing journal. This Journal publish original research work that contributes significantly to further the scientific knowledge in engineering and Technology
Review on the Effect of Corrugated Shapes on the BEHAVIOURS of Fluidjournal ijrtem
Abstract: Corrugated pipe are pipes with rough surfaces walls of discrete grooves regularly disposed along the flow direction. Surface roughness has a significant effect on a wide range of engineering systems such as industrial piping systems, open channel flows, turbo machines, marine, vehicles, and aircraft etc. The d-types and k-type of the roughness were studies and their effect on the flow properties of fluid. Both experimental and numerical analyses of different researchers were reviewed. The rough patterns and results of the researchers were compared. The surface roughness contributed to turbulence, friction loss and enhanced heat transfer depending on the geometrical shape.
Numerical investigation of heat transfer and fluid flow characteristics insid...doda_1989h
Abstract
The combined effect of waviness and porous media on the convection heat transfer and fluid flow characteristics
is numerically investigated. Two models of wavy walled channel fully filled with homogenous porous material
are assumed. The first was the symmetric converging-diverging channel (case A), and the second was the
channel with concave-convex walls (case B). The governing equations have been solved on non-orthogonal grid,
which is generated by Poisson elliptic equations, based on ADI method. Nusselt number values are used to
indicate whether any cases of corrugation studied may have led to an increase in the rate of heat transferred
compared with the planar surface channel which is the purpose of the study. The results show that case A gives
more enhancement in heat transfer than case B. However, the thermal performance of the wavy channels (cases
A & B) is better than the straight channel (simple duct).
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Film Condensation Behaviour of Steam on Isothermal Walls in Presence of Non-C...ijceronline
Numerical modelling of condensation had been a challenging task for the researchers for many years due to its time scale and rapidity. Present work deals with the characterization of condensation in presence of non-condensable gases on isothermal surfaces which is a common situation in many condensing devices. The investigation includes the effect of different flow parameters on condensation of saturated steam-air mixture using a numerical approach. The study uses wall condensation model through ANSYS CFX solver. The effect of mass fraction of steam, operating pressure and mass flow rate of mixture is studied. Investigation provides some key characteristics about film condensation which normally remain absent in condensation without non-condensable gas. The findings of this study will provide valuable insight in thermal design process of components incorporating this phenomenon.
Effect of Wind Direction through Single Storied Building Model Configurations...inventionjournals
International Journal of Engineering and Science Invention (IJESI) is an international journal intended for professionals and researchers in all fields of computer science and electronics. IJESI publishes research articles and reviews within the whole field Engineering Science and Technology, new teaching methods, assessment, validation and the impact of new technologies and it will continue to provide information on the latest trends and developments in this ever-expanding subject. The publications of papers are selected through double peer reviewed to ensure originality, relevance, and readability. The articles published in our journal can be accessed online.
The Journal will bring together leading researchers, engineers and scientists in the domain of interest from around the world. Topics of interest for submission include, but are not limited to:
Effect of Wind Direction through Double Storied Building Model Configurations...inventionjournals
: Effect of wind direction on plume dispersion around urban buildings has been investigated by physical modelling using arrays of buildings- like obstacles at scale 1:100 in boundary layer wind tunnel for double storied buildings and compared with field data. The particular effect of obstacle width- to - height ratio (S/H) was examined for a fixed obstacle plan area density. Series of experiments have been carried out in which the wind direction varied in steps of 5 for selected orientation of line source at 900 , 95, 100 and 105. Further, from the observation, it was concluded that the maximum lateral concentration shift to upward the wind direction of line source is increased for inline double storied buildings model configuration. It can be concluded, the wind tunnel results showed that concentrations at downwind distances decreased as the wind direction increases (positive values) for measured orientation of line source in inline double storied buildings model configuration. In comparison, experimentally observed σz values are below the field values. They were best fitted with power-law profiles. The non-dimensional concentration for both the field and wind tunnel results of double storied inline buildings configuration seems to be more or less uniform. Values of vertical spread parameters for double storied inline array configuration and field data were followed a similar trend but inline array configuration of double storied buildings model, non-dimensional concentrations were typically twice larger compared to the field data. This is attributed to the fact that the tracer material is quite concentrated in the recirculation region in inline array configuration of the double storied buildings model.
An Experimental Study on Vehicular Emission Dispersion through Single Storied...inventionjournals
International Journal of Engineering and Science Invention (IJESI) is an international journal intended for professionals and researchers in all fields of computer science and electronics. IJESI publishes research articles and reviews within the whole field Engineering Science and Technology, new teaching methods, assessment, validation and the impact of new technologies and it will continue to provide information on the latest trends and developments in this ever-expanding subject. The publications of papers are selected through double peer reviewed to ensure originality, relevance, and readability. The articles published in our journal can be accessed online.
Evaluation of Modelling of Flow in Fracturesidescitation
Heat-transport is important for geothermal exploration. The presence of
fractures can have a pronounced effect on groundwater and heat transfer.The inclusion of
fractures into geothermal reservoir models on different scales is often still a difficult task. A
comparison of approaches for flow in fractures has been carried out. A very simple
approach is to simulate fractures with thin but highly conductive layers, for instance by
applying the Cubic-Law. A more sophisticated approach, typically in FEM codes, is the
application of lower dimensional (1D/2D) high permeable discrete elements with specific
flow properties, following e.g. Hagen-Poiseuille or Manning-Strickler. However, such an
approach typically fails while studying only partly saturated fractures. For studying the
applicability of simplified fracture modellingapproaches a comparison with a CFD
(Computational Fluid Dynamics) solution was performed. Furthermore a DEM (Discrete
Element Method)approach has been illuminated. The various methodologies are studied by
varying roughnesses,this way studying the versatility of the approach. The sensitivity of
flow in fractures to various numerical parameters can be studied this way. A detailed
analysis of temperature and flow using Péclet and Reynolds numbers helps to quantify the
contributions of the different transfer processes.
International Journal of Computational Engineering Research(IJCER)ijceronline
International Journal of Computational Engineering Research(IJCER) is an intentional online Journal in English monthly publishing journal. This Journal publish original research work that contributes significantly to further the scientific knowledge in engineering and Technology
Review on the Effect of Corrugated Shapes on the BEHAVIOURS of Fluidjournal ijrtem
Abstract: Corrugated pipe are pipes with rough surfaces walls of discrete grooves regularly disposed along the flow direction. Surface roughness has a significant effect on a wide range of engineering systems such as industrial piping systems, open channel flows, turbo machines, marine, vehicles, and aircraft etc. The d-types and k-type of the roughness were studies and their effect on the flow properties of fluid. Both experimental and numerical analyses of different researchers were reviewed. The rough patterns and results of the researchers were compared. The surface roughness contributed to turbulence, friction loss and enhanced heat transfer depending on the geometrical shape.
Numerical investigation of heat transfer and fluid flow characteristics insid...doda_1989h
Abstract
The combined effect of waviness and porous media on the convection heat transfer and fluid flow characteristics
is numerically investigated. Two models of wavy walled channel fully filled with homogenous porous material
are assumed. The first was the symmetric converging-diverging channel (case A), and the second was the
channel with concave-convex walls (case B). The governing equations have been solved on non-orthogonal grid,
which is generated by Poisson elliptic equations, based on ADI method. Nusselt number values are used to
indicate whether any cases of corrugation studied may have led to an increase in the rate of heat transferred
compared with the planar surface channel which is the purpose of the study. The results show that case A gives
more enhancement in heat transfer than case B. However, the thermal performance of the wavy channels (cases
A & B) is better than the straight channel (simple duct).
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Film Condensation Behaviour of Steam on Isothermal Walls in Presence of Non-C...ijceronline
Numerical modelling of condensation had been a challenging task for the researchers for many years due to its time scale and rapidity. Present work deals with the characterization of condensation in presence of non-condensable gases on isothermal surfaces which is a common situation in many condensing devices. The investigation includes the effect of different flow parameters on condensation of saturated steam-air mixture using a numerical approach. The study uses wall condensation model through ANSYS CFX solver. The effect of mass fraction of steam, operating pressure and mass flow rate of mixture is studied. Investigation provides some key characteristics about film condensation which normally remain absent in condensation without non-condensable gas. The findings of this study will provide valuable insight in thermal design process of components incorporating this phenomenon.
Effect of Wind Direction through Single Storied Building Model Configurations...inventionjournals
International Journal of Engineering and Science Invention (IJESI) is an international journal intended for professionals and researchers in all fields of computer science and electronics. IJESI publishes research articles and reviews within the whole field Engineering Science and Technology, new teaching methods, assessment, validation and the impact of new technologies and it will continue to provide information on the latest trends and developments in this ever-expanding subject. The publications of papers are selected through double peer reviewed to ensure originality, relevance, and readability. The articles published in our journal can be accessed online.
The Journal will bring together leading researchers, engineers and scientists in the domain of interest from around the world. Topics of interest for submission include, but are not limited to:
Effect of Wind Direction through Double Storied Building Model Configurations...inventionjournals
: Effect of wind direction on plume dispersion around urban buildings has been investigated by physical modelling using arrays of buildings- like obstacles at scale 1:100 in boundary layer wind tunnel for double storied buildings and compared with field data. The particular effect of obstacle width- to - height ratio (S/H) was examined for a fixed obstacle plan area density. Series of experiments have been carried out in which the wind direction varied in steps of 5 for selected orientation of line source at 900 , 95, 100 and 105. Further, from the observation, it was concluded that the maximum lateral concentration shift to upward the wind direction of line source is increased for inline double storied buildings model configuration. It can be concluded, the wind tunnel results showed that concentrations at downwind distances decreased as the wind direction increases (positive values) for measured orientation of line source in inline double storied buildings model configuration. In comparison, experimentally observed σz values are below the field values. They were best fitted with power-law profiles. The non-dimensional concentration for both the field and wind tunnel results of double storied inline buildings configuration seems to be more or less uniform. Values of vertical spread parameters for double storied inline array configuration and field data were followed a similar trend but inline array configuration of double storied buildings model, non-dimensional concentrations were typically twice larger compared to the field data. This is attributed to the fact that the tracer material is quite concentrated in the recirculation region in inline array configuration of the double storied buildings model.
An Experimental Study on Vehicular Emission Dispersion through Single Storied...inventionjournals
International Journal of Engineering and Science Invention (IJESI) is an international journal intended for professionals and researchers in all fields of computer science and electronics. IJESI publishes research articles and reviews within the whole field Engineering Science and Technology, new teaching methods, assessment, validation and the impact of new technologies and it will continue to provide information on the latest trends and developments in this ever-expanding subject. The publications of papers are selected through double peer reviewed to ensure originality, relevance, and readability. The articles published in our journal can be accessed online.
45 investigation paper id 0008 edit septianIAESIJEECS
Most numerical studies on flow over buildings simplify the geometry of the roof and assume that it is flat. This may lead to misrepresentation of the flow as the roof of actual buildings contains some sort of roughness. In this study, the flow over the administrative building of Universiti Tenaga Nasional is investigated for multidirectional flow conditions. The actual topology of the building is gridded and simulated using the steady-state Reynolds-averaged Navier-Stokes equation. Four points at the top of the building are identified and the wind statistics at these designated locations at three different heights are investigated. The optimal location with the highest average wind speed and consistent wind speeds for all wind angles is identified and is earmarked as a potential location to install the wind turbine.
Calculation of Fluid Dynamic for Wind Flow around Reinforced Concrete WallsIJERA Editor
A study on the flow phenomena around free-standing walls is important in practical building construction. In the present paper a numerical study is conducted for two- dimensional incompressible steady flow around freestanding walls using low-Re k-co turbulence model. The separation regions downstream the wall and on the roof of the leeward were predicted. Finally, results of numerical simulation are presented in the form of velocity vectors, velocity contour, pressure contours and streamlines
UiPath Test Automation using UiPath Test Suite series, part 3DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 3. In this session, we will cover desktop automation along with UI automation.
Topics covered:
UI automation Introduction,
UI automation Sample
Desktop automation flow
Pradeep Chinnala, Senior Consultant Automation Developer @WonderBotz and UiPath MVP
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
Connector Corner: Automate dynamic content and events by pushing a buttonDianaGray10
Here is something new! In our next Connector Corner webinar, we will demonstrate how you can use a single workflow to:
Create a campaign using Mailchimp with merge tags/fields
Send an interactive Slack channel message (using buttons)
Have the message received by managers and peers along with a test email for review
But there’s more:
In a second workflow supporting the same use case, you’ll see:
Your campaign sent to target colleagues for approval
If the “Approve” button is clicked, a Jira/Zendesk ticket is created for the marketing design team
But—if the “Reject” button is pushed, colleagues will be alerted via Slack message
Join us to learn more about this new, human-in-the-loop capability, brought to you by Integration Service connectors.
And...
Speakers:
Akshay Agnihotri, Product Manager
Charlie Greenberg, Host
Builder.ai Founder Sachin Dev Duggal's Strategic Approach to Create an Innova...Ramesh Iyer
In today's fast-changing business world, Companies that adapt and embrace new ideas often need help to keep up with the competition. However, fostering a culture of innovation takes much work. It takes vision, leadership and willingness to take risks in the right proportion. Sachin Dev Duggal, co-founder of Builder.ai, has perfected the art of this balance, creating a company culture where creativity and growth are nurtured at each stage.
Generating a custom Ruby SDK for your web service or Rails API using Smithyg2nightmarescribd
Have you ever wanted a Ruby client API to communicate with your web service? Smithy is a protocol-agnostic language for defining services and SDKs. Smithy Ruby is an implementation of Smithy that generates a Ruby SDK using a Smithy model. In this talk, we will explore Smithy and Smithy Ruby to learn how to generate custom feature-rich SDKs that can communicate with any web service, such as a Rails JSON API.
Key Trends Shaping the Future of Infrastructure.pdfCheryl Hung
Keynote at DIGIT West Expo, Glasgow on 29 May 2024.
Cheryl Hung, ochery.com
Sr Director, Infrastructure Ecosystem, Arm.
The key trends across hardware, cloud and open-source; exploring how these areas are likely to mature and develop over the short and long-term, and then considering how organisations can position themselves to adapt and thrive.
Smart TV Buyer Insights Survey 2024 by 91mobiles.pdf91mobiles
91mobiles recently conducted a Smart TV Buyer Insights Survey in which we asked over 3,000 respondents about the TV they own, aspects they look at on a new TV, and their TV buying preferences.
Transcript: Selling digital books in 2024: Insights from industry leaders - T...BookNet Canada
The publishing industry has been selling digital audiobooks and ebooks for over a decade and has found its groove. What’s changed? What has stayed the same? Where do we go from here? Join a group of leading sales peers from across the industry for a conversation about the lessons learned since the popularization of digital books, best practices, digital book supply chain management, and more.
Link to video recording: https://bnctechforum.ca/sessions/selling-digital-books-in-2024-insights-from-industry-leaders/
Presented by BookNet Canada on May 28, 2024, with support from the Department of Canadian Heritage.
JMeter webinar - integration with InfluxDB and GrafanaRTTS
Watch this recorded webinar about real-time monitoring of application performance. See how to integrate Apache JMeter, the open-source leader in performance testing, with InfluxDB, the open-source time-series database, and Grafana, the open-source analytics and visualization application.
In this webinar, we will review the benefits of leveraging InfluxDB and Grafana when executing load tests and demonstrate how these tools are used to visualize performance metrics.
Length: 30 minutes
Session Overview
-------------------------------------------
During this webinar, we will cover the following topics while demonstrating the integrations of JMeter, InfluxDB and Grafana:
- What out-of-the-box solutions are available for real-time monitoring JMeter tests?
- What are the benefits of integrating InfluxDB and Grafana into the load testing stack?
- Which features are provided by Grafana?
- Demonstration of InfluxDB and Grafana using a practice web application
To view the webinar recording, go to:
https://www.rttsweb.com/jmeter-integration-webinar
Designing Great Products: The Power of Design and Leadership by Chief Designe...
2 ashrae chapter7
1. 1-1
Chapter 1
Introduction
One of the major causes of poor indoor air quality at some facilities is the sporadic
occurrence of exhaust reingestion at fresh air intakes. University, hospital and industrial
laboratories as well as manufacturing facilities are particularly susceptible to this
phenomenon since they emit a wide range of toxic and odorous chemicals. The effect on
worker health and comfort is substantial. Unfortunately, the state-of-the-art has not been
sufficiently advanced to allow building engineers to apply appropriate design criteria to
avoid this problem for new construction or to help alleviate it for existing buildings.
Consequently, numerous incidents of poor air quality have been recorded and
documented.
The first phase of the study, commissioned by IRSST in 1996 [Stathopoulos et al. (1999)]
provided a significant amount of information on the dispersion of plumes emitted from
buildings in an urban environment. Experiments were performed on two buildings for a
limited number of wind directions; corresponding tests were also carried out in a wind
tunnel. The results indicated that the use of high velocity exhaust stacks does not
guarantee adequate plume dilution at all locations on the roof, and the exhaust
momentum ratio, M (i.e. the ratio of exhaust velocity to wind speed), was found to
significantly influence the dilution of a tracer gas emitted from a stack. Both current
ASHRAE design formulas and wind tunnel modelling may, at a given location,
underpredict the maximum concentration of a contaminant.
2. 1-2
This report describes the second phase of the study, which commenced in January 2000.
The main goals of the study were:
1. Evaluation and improvement of the two most commonly-used modelling tools
(empirical design formulas [e.g. ASHRAE] and wind tunnel simulation) for the
assessment of concentration of rooftop stack exhaust at various locations,
and
2. Development of design guidelines to assist engineers in the proper selection of
location, geometry and functional characteristics of rooftop stacks for various
cases by revising the current models when appropriate.
The study included both field tests and wind tunnel experiments. A series of field tracer
gas experiments were carried out on a 3-storey building in Montreal using a portable fan
as the emission source. The influence of the following factors on short-range plume
dispersion were investigated :
1. location of the stack relative to regions of flow separation;
2. stack height;
3. M-value
4. atmospheric turbulence (associated with roughness of upwind terrain);
5. rooftop structures,
6. a taller upwind adjacent building;
In the field study, sulfur hexafluoride, SF6, was emitted from a variable speed fan located on
the roof. Experiments were carried out for two exhaust speeds (7.5 m/s , 17.5 m/s) and two
stack heights (1 m, 3 m). Tracer gas concentrations were obtained at 15 locations using the
3. 1-3
air sampling methodology developed in the first phase of the study.
Four stack locations were chosen for the study. Field tests performed with the stack at
locations 1 and 2 provided data for cases with high upstream turbulence. Stacks 3 and 4 were
used for tests with a tall upwind building. Stack 4 was also used for an open fetch case with
typical suburban roughness.
A parametric study was carried out in the wind tunnel to provide more detailed
information regarding the influence of stack height and M on plume dispersion.
.
4. 2-1
Chapter 2
Literature Review
Current standards for building ventilation systems recommend that rooftop stacks be
designed such that their emissions do not contaminate fresh air intakes of the emitting
building or nearby buildings. This may require extending the height of the stack, hs, or
increasing its exit velocity, we. The effects of hs and we on concentration distributions on
building surfaces have been investigated using wind tunnel or water channel simulations.
In most of these studies, plume dispersion was evaluated for a single isolated building
model.
Schulman and Scire (1991) carried out a wind tunnel study to investigate the influence of
stack height and exit velocity on the dispersion of emissions from a rooftop stack. The
experiments were performed with an isolated low-rise building with a stack in the center
of the roof. Figure 2.1 shows the influence of stack height on normalized dimensional
concentration, C*=CUH/Qm, where C is the receptor concentration, UH is wind speed at
building height and Qm is the mass flow rate of tracer gas. The results are given for a
typical exhaust velocity, expressed in terms of the exhaust momentum ratio, M=we/UH. In
this case, M=3, which is generally associated with moderately strong winds. The results
show that increasing hs from 0 to 4.6 m causes C* to reduce by a factor of 100 near the
stack. However, at the leeward edge of the building, the increase in stack height produces
only a marginal benefit. The 4.6 m stack has a C* reduction factor of 4.
5. 2-2
Figure 2.2 shows the effect of M on C* for a short stack (hs = 1.5m). The data show that
near the stack, C* can be reduced by a factor of 100 by increasing M from 1.5 to 5. Near
the leeward edge of the building the effect of M is reduced; C* is reduced by a factor of
10 as M is increased from 1.5 to 5.
The potential for reducing indoor pollutant concentrations using hidden (wall) fresh air
intakes was investigated in a wind tunnel study carried out by Petersen and LeCompte
(2002). The study provided a method for predicting concentrations at hidden intakes
based on standard dispersion models (ASHRAE, Gaussian). However, since the results
were obtained with an isolated building model, further tests are required to determine the
applicability of the method for cases when other buildings are nearby.
Meroney et al. (1999) evaluated dispersion and flow patterns around various building
shapes using wind tunnel experiments. Flow visualization experiments demonstrated that
flow recirculation zones are intermittent and consequently, the direction of flow at a
rooftop location may change frequently from upwind to downwind. The authors suggest
that the inaccuracy of CFD dispersion predictions is due, in part, to the absence of
intermittency in the computer model.
Wilson et al. (1998) investigated the effect of hs and we on the dispersion of building
exhaust in a series of water channel experiments. In addition to an isolated low-rise
building, tests were also performed for cases in which an adjacent building was upwind
or downwind of the emitting building.
6. 2-3
Results obtained with a taller upwind building showed that the leeward wall of the
upwind building may experience low dilution values (high concentrations), depending on
stack location, stack height and exhaust velocity. Figure 2.3 shows measurements of
minimum dilution on the leeward wall of the adjacent building due to exhaust from a 2.1
m stack near the leading edge of the emitting building. The dilution values are expressed
in normalized form: DminQe/UHH2
, where Qe is the exhaust volume flow rate and H is the
height of the emitting building.
The results indicate that, for all M, the lowest dilution values occur near the top of the
leeward wall. Dilution increases significantly with increasing M; an increase in M from
1.5 to 8 causes normalized dilution to increase by approximately a factor of 10. On the
roof of the emitting building, dilution did not vary significantly with distance from the
stack. The average dilution on the roof was approximately equal to the minimum dilution
measured on the wall of the adjacent building.
The study found that stacks should not be located near building edges and fresh air
intakes should not be placed on the leeward wall of a building if emissions from a lower
downwind building are toxic or odorous. Furthermore, a lower adjacent building upwind
of the emitting building tends to increase dilution on the emitting building roof, whereas
in the case of a higher upwind building, increasing exhaust velocity is more beneficial
than increasing stack height.
7. 2-4
Fluid modeling studies have demonstrated the benefits of high exit velocities and
increasing stack height in reducing pollutant concentrations at critical receptors.
However, field studies have shown that even with high exit velocities and moderately
high stacks, pollutant concentrations may be unacceptably high at particular locations
[Wilson and Lamb (1994), Georgakis et al. (1995) Saathoff et al. (2002)]. Several factors
may account for the occasional poor performance of rooftop stacks. These factors include
the location of the stack relative to regions of flow separation and flow re-attachment, the
presence of rooftop irregularities such as penthouses and high upstream turbulence.
It is important to validate the results of fundamental fluid modeling studies with full-scale
data. Although most flow features (e.g. wake size, reattachment lengths etc.) under
neutral atmospheric conditions can be accurately simulated in wind tunnels and water
channels, it is necessary to determine the limitations of fluid modeling with respect to
plume dispersion.
Relatively few studies have compared wind tunnel concentration data with field data for
nearfield diffusion cases (i.e. receptors within 50 m of a stack). This is one of the most
difficult fluid modeling applications, since the plume characteristics may be sensitive to a
number of local factors (building wake effects, the position of the stack relative to
rooftop recirculation zones or delta-wing vortices, stack Reynolds number etc.). On the
other hand, for far-field applications, plume characteristics are much less sensitive to
these factors.
8. 2-5
Higson et al. (1994) conducted field tracer gas experiments with a stack at varying
distances upwind of a small rotatable building and compared the results with wind tunnel
data. They found that the maximum concentrations were generally overestimated in the
wind tunnel tests; the minimum concentrations were underestimated. This suggests that
the wind tunnel plume was narrower than the field plume due to the absence of large-
scale turbulence in the wind tunnel.
Several studies by the authors have evaluated the accuracy of wind tunnel dispersion
measurements [Stathopoulos et al. (2002), Saathoff et al. (2002)]. For the most part, the
results indicate good agreement between wind tunnel and field data. The wind tunnel
concentration values were usually within a factor of two of the field values. The accuracy
of the wind tunnel generally increased as stack-receptor distance increased.
9. 2-6
Figure 2.1 Effect of stack height on normalized concentration [from Shulman-Scire
(1991)]
Effect of stack height (M=3.0)
[Schulman-Scire (1991)]
0.00001
0.0001
0.001
0.01
0.1
0 0.1 0.2 0.3 0.4 0.5 0.6
distance from stack (x/L)
C*(m-2)
hs=0
hs=1.5m
hs=4.6 m
10. 2-7
Figure 2.2 Effect of M (exhaust momentum) on normalized concentration [from
Shulman-Scire
(1991)]
Effect of M (hs=1.5m)
[Schulman-Scire (1991)]
0.00001
0.0001
0.001
0.01
0.1
0 0.1 0.2 0.3 0.4 0.5 0.6
distance from stack (x/L)
C*(m-2)
M=1.5
M=3
M=5
11. 2-8
Figure 2.3 Normalized dilutions on the downwind wall of 2H high building with a
downwind emitting building of height, H. Buildings separated by a gap size, H [from
Wilson et al. (1998)]
Predicted
by model
M =1
M = 8
H
12. 3-1
Chapter 3
ASHRAE Dispersion Models
In the present study, experiments can be divided into two types:
1. the emission source exposed to the approaching flow (open fetch)
2. the emission source in the wake of a tall building.
Various models have been developed for estimating nearfield dilution of plumes emitted from
rooftop stacks for open fetch situations. Two such models are recommended in ASHRAE (1999)
and ASHRAE (2003) and are described below. The accuracy of these models will be evaluated in
Chapter 5 using field data obtained in the present study.
For the case of a tall building upwind of an emitting building, dilution estimates are required for
receptors on the adjacent building leeward wall, as well as the roof of the emitting building. To
date, an acceptable dilution model for this case has not been developed [e.g. see Wilson et al.
(1998)].
In addition to dilution models that provide quantitative estimates of plume dispersion, ASHRAE
(2003) also provides a geometric method to predict the likelihood of a plume making contact
with a critical rooftop receptor. This method, which is qualitative in nature, is described below.
3.1 The ASHRAE Geometric Design Method
13. 3-2
ASHRAE (2003) provides a geometric stack design method for estimating the minimum stack
height to avoid plume entrainment in the flow recirculation zones of a building and its rooftop
structures. Dimensions of the recirculation zones are expressed in terms of the scaling length, R,
which is defined as:
R = Bs
0.67
BL
0.33
(3-1)
where Bs is the smaller of upwind building height or width and BL is the larger of these
dimensions. The dimensions of flow re-circulation zones that form on the building and roof-top
structures are:
Hc = 0.22R (3-2)
Xc = 0.5R (3-3)
Lc = 0.9R (3-4)
Lr = 1.0R (3-5)
where Hc is the maximum height of the roof recirculation zone, Xc is the distance from the
leading edge to Hc, Lc is the length of the roof recirculation zone, and Lr is the length of the
building wake zone. Note that the height of the wake zone is equal to the height of the structure.
Figure 3.1 shows the recirculation zones for a typical building.
The design method assumes that the boundary of the high turbulence region is defined by a line
with a slope of 10:1 extending from the top of the leading edge separation bubble. The location of
the plume relative to the recirculation zones is determined by taking into account plume rise due
to exhaust momentum and assuming a conical plume with a slope of 5:1.
14. 3-3
The effective height of the plume above the roof or rooftop structure is:
h = hs + hr – hd (3-6)
where hs is stack height, hr is plume rise and hd is the reduction in plume height due to
entrainment into the stack wake during periods of strong winds. It should be noted that hs is the
height of the stack tip above the roof minus the height of rooftop obstacles (including their
recirculation zones) that are in the path of the plume.
Plume rise, which is assumed to occur instantaneously, is calculated using the formula of Briggs
(1984):
hr = 3βde (we/UH) (3-7)
where de is the stack diameter, we is the exhaust velocity, UH is the wind speed at building height
and β is the stack capping factor. The value of β is 1 for uncapped stacks and 0 for capped stacks.
To account for the stack downwash caused by low exit velocities, when we/UH < 3.0, Wilson et
al. (1998) recommended a stack wake downwash adjustment hd, which is defined as,
hd = de (3.0- βwe/UH) (3-8)
For we/UH > 3.0 there is no stack downwash (hd = 0).
3.2 Dilution Models for an Open Fetch
A number of semi-empirical models have been developed for predicting minimum dilution (Dmin
= Ce/Cmax) of exhaust from rooftop stacks, where Ce is the exhaust concentration and Cmax is the
15. 3-4
concentration at a roof or wall receptor on the plume center-line. The ASHRAE Applications
Handbook [ASHRAE (2003)] recommends a Gaussian dilution model that was developed using
data from water channel experiments of Wilson et al. (1998). In an earlier version of the
Handbook [ASHRAE (1999], minimum dilution models formulated by Wilson and Lamb (1994)
and Halitsky (1963) were recommended. Of these, the Wilson and Lamb model provides a more
accurate lower bound of dilution, based on wind tunnel and field case studies [Petersen and
Wilson (1989), Stathopoulos et al. (2002)]. The Halitsky model has been shown to be overly
conservative in most cases.
In the current study, the accuracy of the Wilson-Lamb and ASHRAE (2003) dilution models will
be evaluated using data obtained in field tests conducted with an open fetch.
3.2.1 The Wilson-Lamb Model
The Wilson-Lamb model, hereafter designated as WL, is based on a previous dilution model for
flush vents (hs = 0) derived from wind tunnel data obtained with isolated building models
[Wilson and Chui (1985, 1987), Chui and Wilson (1988)]. In this model, minimum dilution along
the plume centre-line is given by:
Dmin = (Do
0.5
+ Dd
0.5
)2
(3-9)
where Do is the initial dilution at the location and Dd is the distance dilution which is produced by
atmospheric and building-generated turbulence. The formulas for Do and Dd recommended in
ASHRAE (1999) are:
Do = 1 + 13βM (3-10)
16. 3-5
Dd = B1S2
/MAe (3-11)
where B1 is the distance dilution parameter, S is the stretched string distance from stack to
receptor and M is the ratio of exhaust gas velocity, we, to the mean wind speed at the building
height, UH. The parameter, β, is the stack capping factor and is set equal to 1.0 for uncapped
stacks. The parameter, B1, is set at a constant value with the magnitude dependent on the location
of the receptors.
Dilution data obtained in a field study [Wilson and Lamb (1994)] and a wind tunnel study
[Wilson and Chui (1987)] indicate that B1 is strongly affected by the level of atmospheric
turbulence in the approaching flow. The effect of upstream turbulence on the distance dilution
parameter is approximated by the following formula:
B1 = 0.027 + 0.0021σθ (3-12)
where σθ is the standard deviation of wind direction fluctuations in degrees and varies between 0°
and 30°. The model suggests that distance dilution has two components -- the dilution due to
building-generated turbulence and that due to atmospheric turbulence. It assumes that Dd is
significantly enhanced by atmospheric turbulence. For an urban environment, ASHRAE (1997)
recommends a typical value of σθ =15°, which gives a value of 0.032 for the atmospheric
component of the distance dilution parameter, B1=0.059. Thus, more than 50% of Dd is assumed
to be due to upstream turbulence.
3.2.2 Gaussian Dilution Model (ASHRAE 2003)
17. 3-6
The Gaussian dilution model recommended in ASHRAE (2003) is based on a series of
experiments carried out in a water flume by Wilson et al. (1998). The model predicts worst-case
dilution at roof-level, Dr, assuming that the plume has a Gaussian (bell-shaped) concentration
profile in both the vertical and horizontal directions, as shown in Figure 3.2. It should be noted
that Dr is the predicted dilution on the plume centre-line and thus, corresponds to Dmin obtained
using the WL model.
The roof-level dilution for a plume at height, h, at a receptor distance, X, from the stack is given
as:
= 2
z
2
e
z
e
y
e
H
r
2σ
h
exp
d
σ
d
σ
w
U
4D (3-13)
where UH is the wind speed at the building height, de is stack diameter, we is the exhaust speed
and σy and σz are the plume spreads in the horizontal and vertical directions, respectively. The
height of plume above the roof or rooftop structure, h, is determined using Eq. 6.
The equations for σy and σz are the equations used in the ISCST dispersion model, which was
developed by the U.S. EPA [EPA (1995)], adjusted from a 60 minute averaging time to a 2
minute averaging time using the 0.2 power law applied to both vertical and crosswind spreads.
The plume spread formulas are based on water channel data of Wilson et al. (1998), which are
assumed to have a full-scale equivalent averaging time of 2 minutes.
The cross-wind and vertical spreads are given by the equations,
18. 3-7
e
o
e
0.2avg
e
y
d
σ
d
X
)
2.0
t
0.071(
d
σ
+= (3-14)
e
o
ee
z
d
σ
d
X
0.071
d
σ
+= (3-15)
where tavg is the concentration averaging time in minutes, and σo is the initial source size that
accounts for stack diameter and for dilution due to jet entrainment during plume rise. The
formula for σo/de is:
[ .5
2
H
e
H
e
e
o
0.250]
U
w
0.911β
U
w
.125β0
d
σ
+
+= (3-16)
where β is the rain cap factor, also described previously: β=1 for no rain cap and 0 if the rain cap
is present.
The Gaussian dilution model (Eq. 13) should not be used when the plume height, h, is less than
the maximum height of the roof recirculation zones that are in the path of the plume. This critical
height is referred to as htop and is shown in Figure 3.3. For cases in which the plume height is
greater than htop but less than the height required to escape all critical recirculation zones (hvalid in
Figure 3.3), the physical stack height should be set at 0 when calculating h [ASHRAE (2003)].
19. 3-8
Figure 3.1 Design procedure for required stack height to avoid contamination [from Wilson
(1979)]
20. 3-9
Figure 3.3 Flow recirculation regions and exhaust-to-intake stretched-string distances [from
ASHRAE (2003)]
21. 3-10
Figure 3.2 Coordinate system showing Gaussian distributions in the horizontal and vertical
direction [from Turner (1994)]