The document discusses safety considerations for robotics and manufacturing automation. It covers the Three Laws of Robotics developed by Isaac Asimov, situations that require safety precautions, and standards and codes for industrial robots. It also describes different types of safety hardware used in automated work cells like physical barriers, e-stop devices, presence sensing devices, interlock devices, and safety control units. Specific presence sensing devices discussed in detail are proximity sensing devices like the proximity laser sensor and light curtains. The key applications and specifications of these devices are summarized.
The document provides guidance on machine guarding requirements to protect workers from mechanical hazards. It discusses how hazards can occur at the point of operation, from power transmission devices, and other moving parts. It emphasizes that machine guards, presence-sensing devices, restraints, and other controls should be used to prevent worker contact with dangerous areas of machinery during operation. The overall goal is to design safeguards that prevent injury without interfering with necessary machine functions.
Design & Fabrication of Electro-Pneumatic Gantry Type Sorting RobotIRJET Journal
This document describes the design and fabrication of an electro-pneumatic gantry type sorting robot. The robot uses sensors like proximity sensors and photoelectric sensors connected to a programmable logic controller (PLC) to sort objects on a conveyor belt based on their properties. A human machine interface (HMI) is used to monitor and control the sorting process. Pneumatic cylinders and solenoid valves controlled by the PLC move a gantry system to pick and place objects into different trays for sorting. Calculations are provided on the required forces and selection of components like the conveyor motor and pneumatic cylinders. The PLC controls the sorting process and sequencing of the robot through ladder logic programming.
This document provides an introduction to radar surveillance systems. It explains that radar uses radio waves to detect objects by emitting signals that bounce off objects and return to the receiver. The time it takes allows the radar to calculate distance. The document outlines the components of a radar system including ultrasonic sensors to collect data, an Arduino microcontroller to calculate distance, a servo motor to direct the sensor, and an LCD display to output results. It provides code snippets and diagrams of the system and discusses applications in security, traffic control, and more. In conclusion, the document discusses the advantages of radar and potential future applications like self-driving cars.
Workers face dangerous struck-by hazards from heavy equipment and machinery on busy construction sites. The document provides guidelines to reduce these risks, such as avoiding reversing vehicles when possible, using signallers for necessary backup operations, and ensuring all workers understand equipment blind spots. It also recommends warning devices on vehicles, safe work procedures developed through job hazard analyses, and relevant legislative requirements regarding vehicle operation, traffic control, and powerline safety. Following these practices can help prevent fatalities and injuries from struck-by incidents.
Security System Based on Ultrasonic Sensor TechnologyIOSR Journals
Abstract : In this paper we design and implement a security system with an ultrasonic sensor module to enhance the system’s reliability. The ultrasonic sensor contains a transmitter and a receiver and the module is placed in a rotating motor. It is assumed that an ultrasonic sensor is set in a rotating motor to cover a wide range. The Ultrasonic transmitter periodically emits ultrasonic signals into an open area. A rotating motor is used to allow the sensor to cover whole 360 degrees. If the signal ever hits any physical objects, it will be reflected back and the receiver part of the sensor will then capture it. The microcontroller unit (MCU) will constantly check for the receiver output of the ultrasonic transmitter. If the receiver output is high, the MCU will perform distance analysis of the object from the sensor using the fact that ultrasonic waves travel in air at 340m/s. The time taken for the waves to hit the object and return can be calculated as the time taken for the receiver output to be high after the transmitter has been initiated to send ultrasonic waves. Once the distance is calculated, MCU checks whether the object is within the range threshold specified within the MCU for initiating the alert. If the object is within the range threshold, the MCU initiates a sound alarm and also the global system for mobile communications (GSM) modem to send short message service (SMS) or call to the concerned person. Keywords: GSM Module,Microcontroller unit(MCU),Motor controller driver unit,Ultrasonic sensor(obstacles detection).
An electronic switch sensor with a point to-point intrusive monitoring systemZac Darcy
Sophistications in theft and other criminal damages necessitates for the symbiotic blending of technology with security needs. In this research, electronic switches in the form of sensors were used to implement a point-to point intrusive monitoring system for the detection of an unauthorized access to commercial and residential buildings. The system is a simple and reliable security system and uses switch sensor technology to revolutionize the standards of living. The system is also simple, adaptable and cost-effective. It is designed in six major units which include; the power supply, the input/sensor micro-switches, the monitoring and indicator, the timing, the tone generation and output units. To ensure steady power supply in the circuit, the power unit constitutes both the mains and DC supplies. The alarm unit are being activated by the normally closed sensor micro-switches unit which is connected in an electronic/door mat at both the entrance and exit of buildings. In order to facilitate easy location of the intruder, the exact point of intrusion is being determined by the monitoring and indicator unit which constitutes the quad R/S flip-flop IC and LED’s. The timing/tone generation unit is built on the 555 timer IC, in the Astable mode, which output keeps changing as far as there is a breakage of the sensors. The output of the system is mainly the LEDs and buzzer, which gives electrical light and audio signal to notify the owner of an intruder in the building. Major design issues considered include; efficiency, portability, cost-effectiveness, durability, compatibility as well as the availability of required materials. This system works on the principle of the micro-switch sensor and dependent on the condition that an intruder entered through the door and stepped in any one of the switches under the mat. Verification and validation of the system indicate compliances to design specification hence the output requirements were met.
The document provides guidance on machine guarding requirements to protect workers from mechanical hazards. It discusses how hazards can occur at the point of operation, from power transmission devices, and other moving parts. It emphasizes that machine guards, presence-sensing devices, restraints, and other controls should be used to prevent worker contact with dangerous areas of machinery during operation. The overall goal is to design safeguards that prevent injury without interfering with necessary machine functions.
Design & Fabrication of Electro-Pneumatic Gantry Type Sorting RobotIRJET Journal
This document describes the design and fabrication of an electro-pneumatic gantry type sorting robot. The robot uses sensors like proximity sensors and photoelectric sensors connected to a programmable logic controller (PLC) to sort objects on a conveyor belt based on their properties. A human machine interface (HMI) is used to monitor and control the sorting process. Pneumatic cylinders and solenoid valves controlled by the PLC move a gantry system to pick and place objects into different trays for sorting. Calculations are provided on the required forces and selection of components like the conveyor motor and pneumatic cylinders. The PLC controls the sorting process and sequencing of the robot through ladder logic programming.
This document provides an introduction to radar surveillance systems. It explains that radar uses radio waves to detect objects by emitting signals that bounce off objects and return to the receiver. The time it takes allows the radar to calculate distance. The document outlines the components of a radar system including ultrasonic sensors to collect data, an Arduino microcontroller to calculate distance, a servo motor to direct the sensor, and an LCD display to output results. It provides code snippets and diagrams of the system and discusses applications in security, traffic control, and more. In conclusion, the document discusses the advantages of radar and potential future applications like self-driving cars.
Workers face dangerous struck-by hazards from heavy equipment and machinery on busy construction sites. The document provides guidelines to reduce these risks, such as avoiding reversing vehicles when possible, using signallers for necessary backup operations, and ensuring all workers understand equipment blind spots. It also recommends warning devices on vehicles, safe work procedures developed through job hazard analyses, and relevant legislative requirements regarding vehicle operation, traffic control, and powerline safety. Following these practices can help prevent fatalities and injuries from struck-by incidents.
Security System Based on Ultrasonic Sensor TechnologyIOSR Journals
Abstract : In this paper we design and implement a security system with an ultrasonic sensor module to enhance the system’s reliability. The ultrasonic sensor contains a transmitter and a receiver and the module is placed in a rotating motor. It is assumed that an ultrasonic sensor is set in a rotating motor to cover a wide range. The Ultrasonic transmitter periodically emits ultrasonic signals into an open area. A rotating motor is used to allow the sensor to cover whole 360 degrees. If the signal ever hits any physical objects, it will be reflected back and the receiver part of the sensor will then capture it. The microcontroller unit (MCU) will constantly check for the receiver output of the ultrasonic transmitter. If the receiver output is high, the MCU will perform distance analysis of the object from the sensor using the fact that ultrasonic waves travel in air at 340m/s. The time taken for the waves to hit the object and return can be calculated as the time taken for the receiver output to be high after the transmitter has been initiated to send ultrasonic waves. Once the distance is calculated, MCU checks whether the object is within the range threshold specified within the MCU for initiating the alert. If the object is within the range threshold, the MCU initiates a sound alarm and also the global system for mobile communications (GSM) modem to send short message service (SMS) or call to the concerned person. Keywords: GSM Module,Microcontroller unit(MCU),Motor controller driver unit,Ultrasonic sensor(obstacles detection).
An electronic switch sensor with a point to-point intrusive monitoring systemZac Darcy
Sophistications in theft and other criminal damages necessitates for the symbiotic blending of technology with security needs. In this research, electronic switches in the form of sensors were used to implement a point-to point intrusive monitoring system for the detection of an unauthorized access to commercial and residential buildings. The system is a simple and reliable security system and uses switch sensor technology to revolutionize the standards of living. The system is also simple, adaptable and cost-effective. It is designed in six major units which include; the power supply, the input/sensor micro-switches, the monitoring and indicator, the timing, the tone generation and output units. To ensure steady power supply in the circuit, the power unit constitutes both the mains and DC supplies. The alarm unit are being activated by the normally closed sensor micro-switches unit which is connected in an electronic/door mat at both the entrance and exit of buildings. In order to facilitate easy location of the intruder, the exact point of intrusion is being determined by the monitoring and indicator unit which constitutes the quad R/S flip-flop IC and LED’s. The timing/tone generation unit is built on the 555 timer IC, in the Astable mode, which output keeps changing as far as there is a breakage of the sensors. The output of the system is mainly the LEDs and buzzer, which gives electrical light and audio signal to notify the owner of an intruder in the building. Major design issues considered include; efficiency, portability, cost-effectiveness, durability, compatibility as well as the availability of required materials. This system works on the principle of the micro-switch sensor and dependent on the condition that an intruder entered through the door and stepped in any one of the switches under the mat. Verification and validation of the system indicate compliances to design specification hence the output requirements were met.
This document describes a project to detect faults in transmission lines using an Arduino board. The system uses sensors to detect over voltage, fire, short circuits, and open circuits. When a fault is detected, the Arduino sends a signal to an LCD display and buzzer. It also sends an SMS using GSM to notify operators of the specific fault and location. The system aims to quickly identify faults to protect equipment and reduce power outages. It provides real-time monitoring of transmission lines to improve efficiency and system stability.
This document presents a project aimed at protecting linemen working on transmission lines. The project uses a microcontroller and GSM modem to provide safety for linemen. When a lineman is working, a known password must be entered through the GSM for loads to be switched on the transmission line. If an incorrect password is entered, the loads will not be switched on. The system helps avoid accidents on transmission and distribution lines by ensuring safety precautions are followed. It has advantages such as only operating with a known password, providing effective safety for workers, being economical and easy to install.
https://technoelectronics44.blogspot.com/
ULTRASONIC SENSOR RANGE FIND OUT, it has Implemented by using ULTRASONIC SENSOR, 8051 microcontrollers, LCD display, and a sound indicator.
This document discusses vibration monitoring and analysis techniques for machine maintenance. It covers three types of maintenance schemes: breakdown, preventive, and condition-based maintenance. Vibration monitoring is described as the most common condition monitoring method, where vibration levels are measured to predict failures. Two types of vibration monitoring systems - periodic and permanent - are outlined. Vibration analysis techniques including time-domain and frequency-domain analysis are explained. Data acquisition and interpretation methods are also summarized. The role of computers in vibration-based condition monitoring programs is briefly described.
This document describes an automatic safety door lock system for cars that uses infrared sensors and a hydraulic piston to prevent injuries caused by closing car doors. The system uses IR sensors placed along the door and outer panel connected to a microcontroller. When an object is detected between the closing door and outer panel, the sensors transmit a signal to the microcontroller which activates a relay driver to extend the hydraulic piston to stop the door from closing. The system aims to prevent the over 120,000 injuries that occur annually from unexpected car door closings.
This document establishes requirements for safeguarding machine tools. It addresses guards, safeguarding devices, awareness devices, safe work procedures and other safety measures. It requires components to meet specific failure criteria to ensure safety functions are not compromised. It also provides guidelines for interlocks, presence sensing devices, muting, safety mats, emergency stops and complementary safety equipment. The goal is to eliminate hazards and control risks, though some risk cannot be entirely removed.
An alarm device or system of alarm devices gives an audible, visual or other form of alarm signal about a problem or condition. Alarm devices are often outfitted with a siren.
Alarms in an operation and maintenance (O&M) monitoring system, which informs the bad working state of (a particular part of) the system under monitoring. First-out alarm safety alarms, which go off if a dangerous condition occurs.
Iaetsd real time implementation of railwayIaetsd Iaetsd
The document describes a proposed system for detecting faults in railway tracks using infrared and ultrasonic sensors on an autonomous robotic vehicle. The sensors would detect cracks and gaps in the tracks. If a dangerous fault is found, the system would send an alarm to the railway control room along with details of the location from the GPS. Less serious faults would also be reported. This would allow for more regular, low-cost inspections of tracks compared to manual methods, improving safety.
MACHINE SAFEGUARDING TRAINING & PSHR requirements by JULIAN KALACJulian Kalac P.Eng
The document discusses machine guarding and safety reviews. It describes an incident where a printing press operator suffered severe injuries to their hand from an unguarded pinch point. It then outlines responsibilities for management, supervisors, and employees to ensure machinery is properly safeguarded. The document provides examples of machine hazards that require guarding and different types of guards that can be used. It emphasizes that guards must never be removed without supervision and machines locked out.
This document describes the design of a flying spy robot. It lists the objectives as minimizing human casualties from terrorist attacks by using the robot for military, restaurant, hotel, and spy purposes. It can monitor enemy areas remotely using a wireless camera. The document discusses the requirements for and parts of the robot, including sensors, a controller, motors, wings, a power system, and a base. It also provides block diagrams and discusses applications in hazardous environments, defense, security, and anti-terrorism. The conclusion states that such robots could help avoid terrorist disasters and ensure security.
Emergency vehicle detection system using rf module and ultrasonic sensorIRJET Journal
This document describes an emergency vehicle detection system that uses RF modules and ultrasonic sensors to clear lanes and avoid collisions. The system aims to reduce delays and accidents involving emergency response vehicles (ERVs) by controlling nearby vehicles' speeds. When an ultrasonic sensor on an ERV detects an obstacle too close, it sends a control signal to that vehicle's microcontroller to limit its speed. RF transmitters and receivers enable communication between the ERV and other vehicles to issue warning signals and adjust speeds as needed for lane clearance and collision avoidance. The system is intended to provide greater safety for ERVs through intelligent control of nearby traffic.
This document provides an introduction to Arduino and robotics. It begins with an overview of Arduino, including the different types of Arduino boards such as the Arduino UNO. It then discusses sensors that can be used with Arduino like light sensors. The document covers Arduino coding concepts such as data types, statements, operators, and control structures. It also introduces robotics, including the components of robots like sensors, controllers, effectors, and actuators. Examples of different actuator types are given. Finally, the document briefly discusses the scope of the robotic industry in Bangladesh and provides some resource links.
International Journal of Computational Engineering Research(IJCER)ijceronline
International Journal of Computational Engineering Research(IJCER) is an intentional online Journal in English monthly publishing journal. This Journal publish original research work that contributes significantly to further the scientific knowledge in engineering and Technology
The document describes the design of an automatic braking system for vehicles using infrared sensors. The system works by emitting infrared waves from the front of the vehicle and detecting reflections from any obstacles. Based on the distance measured, a relay activates a DC gear motor that controls the vehicle's brakes. The objectives are to avoid accidents by braking automatically when the driver cannot respond in time. Key components are IR sensors for detection, a relay for signal processing, and a DC gear motor connected to the wheels for braking. The system was tested successfully by braking when obstacles were sensed at various distances.
The focus of the Indian Railways is to increase capacity utilization of existing assets including rolling stock, track infrastructure, traction power and signalling & telecommunications. By running more high speed trains on the existing infrastructure, passengers and freight carrying capacity as well as revenue and profitability can be increased. In order to ensure safety over high speed and high density rail networks of Indian Railways it is the need of the hour to implement Automatic Train Protection (ATP) system such as Train Collision Avoidance System (TCAS). Indian Railways have taken up indigenous development of Train Collision Avoidance System (TCAS) through Research Designs & Standards Organization (RDSO) to prevent dangerous train collisions caused due to human errors or limitations and equipment failures by providing additional layer of enhanced safety in the operations.
Robotics is the branch of technology that deals with the design, construction, operation, and application of robots. A robot is usually an electro-mechanical machine that can be programmed and guided by a computer to perform tasks automatically. Isaac Asimov popularized the three laws of robotics: 1) a robot cannot harm a human, 2) a robot must obey human orders unless they conflict with the first law, and 3) a robot must protect its own existence as long as it does not conflict with the first two laws. Common robot projects include line-following robots, wall-following robots, and robots that use sensors like IR sensors, temperature sensors, and timers.
IRJET- Industrial Disaster Control System using Hanging RobotIRJET Journal
This document describes an industrial disaster control system using a hanging robot. The proposed system uses a hanging robot that can travel along rope paths to continuously monitor industries. The robot is equipped with gas, temperature, and light sensors to detect abnormal conditions. If sensor values exceed thresholds, an alert is sent to authorities and a buzzer is activated. The system also includes a ground unit with a fire extinguisher that is activated if a fire is detected, helping prevent further damage. The hanging robot design aims to detect issues early and minimize industrial damage from disasters.
This document presents a sensor-based home and industrial security system that uses less electricity and memory than traditional surveillance cameras. The system uses various sensors like motion, sound and thermal sensors to detect security events. When an event is detected, the sensors trigger a relay that activates the surveillance camera and transmitter to record high quality video footage and send an alert signal. After a set time with no detection, a timer stops the recording and signals to conserve resources. The system aims to improve on constant recording by traditional cameras that uses significant electricity and storage.
This paper presents home office and industrial security system using sensor based surveillance
camera which consumes less amount of electricity & memory. It also increases product lifetime and ensure better
performance.
Automatic convey or System with In–Process Sorting Mechanism using PLC and HM...IJERA Editor
Programmable logic controllers are widely used in many manufacturing process like machinery packaging
material handling automatic assembly. These are special type of microprocessor based controller used for any
application that needs any kind of electrical controller including lighting controller and HVAC control system.
Automatic conveyor system is a computerized control method of controlling and managing the sorting
mechanism at the same time maintaining the efficiency of the industry & quality of the products.HMI for
automatic conveyor system is considered the primary way of controlling each operation. Text displays are
available as well as graphical touch screens. It is used in touch panels and local monitoring of machines. This
paper deals with the efficient use of PLC in automatic conveyor system and also building the accuracy in it.
This document describes a project to detect faults in transmission lines using an Arduino board. The system uses sensors to detect over voltage, fire, short circuits, and open circuits. When a fault is detected, the Arduino sends a signal to an LCD display and buzzer. It also sends an SMS using GSM to notify operators of the specific fault and location. The system aims to quickly identify faults to protect equipment and reduce power outages. It provides real-time monitoring of transmission lines to improve efficiency and system stability.
This document presents a project aimed at protecting linemen working on transmission lines. The project uses a microcontroller and GSM modem to provide safety for linemen. When a lineman is working, a known password must be entered through the GSM for loads to be switched on the transmission line. If an incorrect password is entered, the loads will not be switched on. The system helps avoid accidents on transmission and distribution lines by ensuring safety precautions are followed. It has advantages such as only operating with a known password, providing effective safety for workers, being economical and easy to install.
https://technoelectronics44.blogspot.com/
ULTRASONIC SENSOR RANGE FIND OUT, it has Implemented by using ULTRASONIC SENSOR, 8051 microcontrollers, LCD display, and a sound indicator.
This document discusses vibration monitoring and analysis techniques for machine maintenance. It covers three types of maintenance schemes: breakdown, preventive, and condition-based maintenance. Vibration monitoring is described as the most common condition monitoring method, where vibration levels are measured to predict failures. Two types of vibration monitoring systems - periodic and permanent - are outlined. Vibration analysis techniques including time-domain and frequency-domain analysis are explained. Data acquisition and interpretation methods are also summarized. The role of computers in vibration-based condition monitoring programs is briefly described.
This document describes an automatic safety door lock system for cars that uses infrared sensors and a hydraulic piston to prevent injuries caused by closing car doors. The system uses IR sensors placed along the door and outer panel connected to a microcontroller. When an object is detected between the closing door and outer panel, the sensors transmit a signal to the microcontroller which activates a relay driver to extend the hydraulic piston to stop the door from closing. The system aims to prevent the over 120,000 injuries that occur annually from unexpected car door closings.
This document establishes requirements for safeguarding machine tools. It addresses guards, safeguarding devices, awareness devices, safe work procedures and other safety measures. It requires components to meet specific failure criteria to ensure safety functions are not compromised. It also provides guidelines for interlocks, presence sensing devices, muting, safety mats, emergency stops and complementary safety equipment. The goal is to eliminate hazards and control risks, though some risk cannot be entirely removed.
An alarm device or system of alarm devices gives an audible, visual or other form of alarm signal about a problem or condition. Alarm devices are often outfitted with a siren.
Alarms in an operation and maintenance (O&M) monitoring system, which informs the bad working state of (a particular part of) the system under monitoring. First-out alarm safety alarms, which go off if a dangerous condition occurs.
Iaetsd real time implementation of railwayIaetsd Iaetsd
The document describes a proposed system for detecting faults in railway tracks using infrared and ultrasonic sensors on an autonomous robotic vehicle. The sensors would detect cracks and gaps in the tracks. If a dangerous fault is found, the system would send an alarm to the railway control room along with details of the location from the GPS. Less serious faults would also be reported. This would allow for more regular, low-cost inspections of tracks compared to manual methods, improving safety.
MACHINE SAFEGUARDING TRAINING & PSHR requirements by JULIAN KALACJulian Kalac P.Eng
The document discusses machine guarding and safety reviews. It describes an incident where a printing press operator suffered severe injuries to their hand from an unguarded pinch point. It then outlines responsibilities for management, supervisors, and employees to ensure machinery is properly safeguarded. The document provides examples of machine hazards that require guarding and different types of guards that can be used. It emphasizes that guards must never be removed without supervision and machines locked out.
This document describes the design of a flying spy robot. It lists the objectives as minimizing human casualties from terrorist attacks by using the robot for military, restaurant, hotel, and spy purposes. It can monitor enemy areas remotely using a wireless camera. The document discusses the requirements for and parts of the robot, including sensors, a controller, motors, wings, a power system, and a base. It also provides block diagrams and discusses applications in hazardous environments, defense, security, and anti-terrorism. The conclusion states that such robots could help avoid terrorist disasters and ensure security.
Emergency vehicle detection system using rf module and ultrasonic sensorIRJET Journal
This document describes an emergency vehicle detection system that uses RF modules and ultrasonic sensors to clear lanes and avoid collisions. The system aims to reduce delays and accidents involving emergency response vehicles (ERVs) by controlling nearby vehicles' speeds. When an ultrasonic sensor on an ERV detects an obstacle too close, it sends a control signal to that vehicle's microcontroller to limit its speed. RF transmitters and receivers enable communication between the ERV and other vehicles to issue warning signals and adjust speeds as needed for lane clearance and collision avoidance. The system is intended to provide greater safety for ERVs through intelligent control of nearby traffic.
This document provides an introduction to Arduino and robotics. It begins with an overview of Arduino, including the different types of Arduino boards such as the Arduino UNO. It then discusses sensors that can be used with Arduino like light sensors. The document covers Arduino coding concepts such as data types, statements, operators, and control structures. It also introduces robotics, including the components of robots like sensors, controllers, effectors, and actuators. Examples of different actuator types are given. Finally, the document briefly discusses the scope of the robotic industry in Bangladesh and provides some resource links.
International Journal of Computational Engineering Research(IJCER)ijceronline
International Journal of Computational Engineering Research(IJCER) is an intentional online Journal in English monthly publishing journal. This Journal publish original research work that contributes significantly to further the scientific knowledge in engineering and Technology
The document describes the design of an automatic braking system for vehicles using infrared sensors. The system works by emitting infrared waves from the front of the vehicle and detecting reflections from any obstacles. Based on the distance measured, a relay activates a DC gear motor that controls the vehicle's brakes. The objectives are to avoid accidents by braking automatically when the driver cannot respond in time. Key components are IR sensors for detection, a relay for signal processing, and a DC gear motor connected to the wheels for braking. The system was tested successfully by braking when obstacles were sensed at various distances.
The focus of the Indian Railways is to increase capacity utilization of existing assets including rolling stock, track infrastructure, traction power and signalling & telecommunications. By running more high speed trains on the existing infrastructure, passengers and freight carrying capacity as well as revenue and profitability can be increased. In order to ensure safety over high speed and high density rail networks of Indian Railways it is the need of the hour to implement Automatic Train Protection (ATP) system such as Train Collision Avoidance System (TCAS). Indian Railways have taken up indigenous development of Train Collision Avoidance System (TCAS) through Research Designs & Standards Organization (RDSO) to prevent dangerous train collisions caused due to human errors or limitations and equipment failures by providing additional layer of enhanced safety in the operations.
Robotics is the branch of technology that deals with the design, construction, operation, and application of robots. A robot is usually an electro-mechanical machine that can be programmed and guided by a computer to perform tasks automatically. Isaac Asimov popularized the three laws of robotics: 1) a robot cannot harm a human, 2) a robot must obey human orders unless they conflict with the first law, and 3) a robot must protect its own existence as long as it does not conflict with the first two laws. Common robot projects include line-following robots, wall-following robots, and robots that use sensors like IR sensors, temperature sensors, and timers.
IRJET- Industrial Disaster Control System using Hanging RobotIRJET Journal
This document describes an industrial disaster control system using a hanging robot. The proposed system uses a hanging robot that can travel along rope paths to continuously monitor industries. The robot is equipped with gas, temperature, and light sensors to detect abnormal conditions. If sensor values exceed thresholds, an alert is sent to authorities and a buzzer is activated. The system also includes a ground unit with a fire extinguisher that is activated if a fire is detected, helping prevent further damage. The hanging robot design aims to detect issues early and minimize industrial damage from disasters.
This document presents a sensor-based home and industrial security system that uses less electricity and memory than traditional surveillance cameras. The system uses various sensors like motion, sound and thermal sensors to detect security events. When an event is detected, the sensors trigger a relay that activates the surveillance camera and transmitter to record high quality video footage and send an alert signal. After a set time with no detection, a timer stops the recording and signals to conserve resources. The system aims to improve on constant recording by traditional cameras that uses significant electricity and storage.
This paper presents home office and industrial security system using sensor based surveillance
camera which consumes less amount of electricity & memory. It also increases product lifetime and ensure better
performance.
Automatic convey or System with In–Process Sorting Mechanism using PLC and HM...IJERA Editor
Programmable logic controllers are widely used in many manufacturing process like machinery packaging
material handling automatic assembly. These are special type of microprocessor based controller used for any
application that needs any kind of electrical controller including lighting controller and HVAC control system.
Automatic conveyor system is a computerized control method of controlling and managing the sorting
mechanism at the same time maintaining the efficiency of the industry & quality of the products.HMI for
automatic conveyor system is considered the primary way of controlling each operation. Text displays are
available as well as graphical touch screens. It is used in touch panels and local monitoring of machines. This
paper deals with the efficient use of PLC in automatic conveyor system and also building the accuracy in it.
Similar to 09-Chapter_9_Safety_in_Robotics_and_Manufacturing_Automation_Final.pdf (20)
Determination of Equivalent Circuit parameters and performance characteristic...pvpriya2
Includes the testing of induction motor to draw the circle diagram of induction motor with step wise procedure and calculation for the same. Also explains the working and application of Induction generator
Digital Twins Computer Networking Paper Presentation.pptxaryanpankaj78
A Digital Twin in computer networking is a virtual representation of a physical network, used to simulate, analyze, and optimize network performance and reliability. It leverages real-time data to enhance network management, predict issues, and improve decision-making processes.
We have designed & manufacture the Lubi Valves LBF series type of Butterfly Valves for General Utility Water applications as well as for HVAC applications.
Build the Next Generation of Apps with the Einstein 1 Platform.
Rejoignez Philippe Ozil pour une session de workshops qui vous guidera à travers les détails de la plateforme Einstein 1, l'importance des données pour la création d'applications d'intelligence artificielle et les différents outils et technologies que Salesforce propose pour vous apporter tous les bénéfices de l'IA.
Applications of artificial Intelligence in Mechanical Engineering.pdfAtif Razi
Historically, mechanical engineering has relied heavily on human expertise and empirical methods to solve complex problems. With the introduction of computer-aided design (CAD) and finite element analysis (FEA), the field took its first steps towards digitization. These tools allowed engineers to simulate and analyze mechanical systems with greater accuracy and efficiency. However, the sheer volume of data generated by modern engineering systems and the increasing complexity of these systems have necessitated more advanced analytical tools, paving the way for AI.
AI offers the capability to process vast amounts of data, identify patterns, and make predictions with a level of speed and accuracy unattainable by traditional methods. This has profound implications for mechanical engineering, enabling more efficient design processes, predictive maintenance strategies, and optimized manufacturing operations. AI-driven tools can learn from historical data, adapt to new information, and continuously improve their performance, making them invaluable in tackling the multifaceted challenges of modern mechanical engineering.
3rd International Conference on Artificial Intelligence Advances (AIAD 2024)GiselleginaGloria
3rd International Conference on Artificial Intelligence Advances (AIAD 2024) will act as a major forum for the presentation of innovative ideas, approaches, developments, and research projects in the area advanced Artificial Intelligence. It will also serve to facilitate the exchange of information between researchers and industry professionals to discuss the latest issues and advancement in the research area. Core areas of AI and advanced multi-disciplinary and its applications will be covered during the conferences.
2. The Three Laws of Robotics:
The laws were developed by Isaac Asimov (in
1940s and 1950s), the science fiction writer:
1. A robot must not harm a human being, nor
through inaction allow one to come to harm
2. A robot must always obey human beings, unless
that is in conflict with the first law
3. A robot must protect itself from harm, unless that
is in conflict with the first and second law
These laws are still valid today, and safety
considerations must be included.
2
3. Situations requiring safety
1. When repairing malfunctioning robot
2. When other equipment fails
3. During maintenance of robots
4. During reprogramming of robots
5. During robot operations
3
5. Table on Standards and codes for industrial
robots
5
Group Standard Subject
1. ANSI/RIA R1056-1986 American national standards for industrial robots
and robot systems
2. BSR/RIA BSR/RIA R15-06-19XX Proposed standard for industrial robots and robot
systems
3. ANSI/RIA R15.02-1990 American national standard human engineering
design criteria for hand-held robot control pendants
4. OSHA Pub. 2254 (revised) Training requirements in standards and training
guidelines
5. NIOSH Pub. 88-108 Safe maintenance guidelines for robotics
workstations
6. OSHA Pub. 8-1.3, 1987 Guidelines for robotics safety
7. OSHA 29 CFR 1910.147 Control of hazardous energy source (lockout/tagout
final rule)
8. AFOSH 127-12, 1991 Occupational safety machinery
ANSI/RIA = American National Standards Institutes/Robotics Industrial Association.
BSR/RIA = Bureau of Standards Review/Robotics Industrial Association.
NIOSH = National Institute for Occupational Safety and Health.
OSHA = Occupational Safety and Health Administration.
AFOSH = Department of the Air Force.
6. SAFEGUARDING A WORK CELL
• The responsibility for safeguarding a robotic
cell falls on the user. The standards address
safeguarding by considering four points:
1. Devices to be used
2. Operator safety
3. Safety of the teacher
4. Safeguarding maintenance and repair
personnel
6
7. Safety Zones
• Zone 1 : is the area outside the work cell and has no
restrictions on human traffic
• Zone 2: is the area inside the work cell but out of reach
of the robot arm. Only programmers, work-cell
operators, and maintenance personnel are allowed in
this area.
• Zone 3: is the area inside the robot work envelope,
and it cannot be entered as long as the robot is in the
automatic or run mode. Penetration is permitted
during programming or maintenance but only after
safety standards established for the type of robot
present have been satisfied.
7
Zone 1
Zone 2
Zone 3
Robot
Zone 1: typically distinguished by signs and yellow lights. A continuous barrier with electrical
interlocks is usually installed to separate zones 1 and 2.
Zone 3: usually distinguished by an outline on the floor indicating the robot’s maximum
reach. In addition, awareness alarm electronic detectors are frequently used in zones 2 and 3.
8. Safety hardware
Physical Barriers: Physical barriers are the first line of defense in
protecting people from hazards. These include:
• Chains and guard posts
• Safety rails
• Wire mesh fencing
• Equipment within the work cell
The last item, when combined with guard rails and fences, provides
effective safety protection at reduced cost.
E-stop Devices: switches with various tripping mechanisms remove
power to production machines in emergency situations. The most
common E-stop devices are the mushroom pushbutton and grab wire
switches.
8
9. Safety hardware
Presence Sensing Devices: sense the presence of a person and cause
the appropriate action to safeguard the person from any hazardous
condition. The common examples include light curtains, pressure
sensing pads, and proximity sensing devices.
9
10. Safety hardware
Interlock Devices: these are switches that interlock a guard door with
the power source of the hazard. Power interlocking and control
interlocking are the two types of control most frequently used.
Contact and non-contact switches are used with various tripping
mechanism that include actuator operated, hinge operated, cam
operated, active actuator non-contact, unconditional guard
unlocking, and conditional guard unlocking.
Figure : Special limit switches
designed for work in safety systems
(Omron Electronics, LLC)
Safety Control Units: are the intelligent controllers that link elements of
the safety system together and interface the safety system to the rest
of the automated cell hardware.
10
11. Presence Sensing Devices
Three devices commonly used in automated work cells to
sense the presence of a human: proximity sensing
devices, light curtains and pressure sensitive mats.
Proximity Sensing Devices: uses ultrasonic and laser
technologies used to sense the presence of human from a
single sensing location.
Proximity laser sensor (PLS) is a programmable single point
safety device that can pattern a protective field to an
irregularly shaped production area. It covers a
180 degree field of view without reflectors or
separate receivers.
11
12. The PLS creates 3 independent user-defined sensing fields, using an infrared
laser beam and time-of-flight measurements. The fields include two
programmable protected zones (the safety zone and the early warning zone)
and a surveyed area zone. (See Figure below).
• Entrance into the early warning
zone initiates a warning signal,
and movement into the safety
zone would stop any hazardous
machine motion.
• The surveyed area is used to
support positioning and
navigation for AGVs.
• The safe guarded zone are set
using a learn mode in the PLS, or
they are defined by the
programmer using a Windows-
based programming language
in the graphic input mode or the
coordinate input mode.
12
Figure: Typical Layout of the PLS System.
13. Technical specification of the PLS
System
13
Scanning range Safety zone radius
Early warning zone radius
Surveyed area radius
4 m (13 ft)
15 m (48 ft)
50 m (164 ft)
Object
sensitivity
70 mm (2.75 in.) at 4 m scanning
range (variable at closer range)
Response time Less or equal to 80 mm safety zone.
Less or equal to 40 mm safety zone
Safety category Single component failure
detectability; EN 954, Category 3
14. Light curtains
Light curtain Introduction
• Light curtains (also called light screens, optical guards, and
presence sensing devices) provide guarding with a degree of
flexibility and reduced operator fatigue when compared to
traditional guarding methods such as mechanical barriers, gates,
and pull-back restraints. Safety light curtains simplify routine tasks
such as machine setup, maintenance, and repair by replacing solid
guards.
Light curtain Operation
• In a light curtain a photoelectric transmitter sends an array of
synchronized parallel infrared light beams to a receiver unit. If an
opaque object interrupts one or more beams, the light curtain
controller sends a stop signal to the guarded machine. The light
curtain in Figure illustrates this concept. Light emitting diodes (LEDs)
in the transmitter are energized by the light curtain’s timing and
logic circuitry and emit pulses of invisible infrared light.
14
15. Light curtains
The light pulses of individual diodes are energized one after another
and are modulated at the specific frequency. Phototransistors and
logic circuitry in the receiving unit detect only the specific pulse and
designated frequency of the sending diode. This technique ensures
safe operation and rejection of external light sources.
15
A controller interfaces the
curtain to guarded machine
and work cell hardware, and
provides user controls,
status and diagnostic
indication, and power from
curtain operation. A light
curtain from Omron is
pictured in the Figure . Figure: Light curtain
System components
16. Light curtains
• The light curtain is different from a standard photoelectric sensor
because of a concept called control reliability. Control reliability is
a design standard from OSHA and ANSI (ANSI B11.19-1990, 5.5) for
safety related machine control system. It stated that:
• The device, system, or interface shall be designed, constructed,
and installed such that a single component failure within the
device, interface, or system shall not prevent normal stopping
action from taking place but shall prevent a successive machine
cycle.
16
Example of control reliability design include
self-checking circuitry, which monitors the
curtain from internal faults by using lockouts
to stop the guarded machine until the fault is
corrected and the system is reset. Redundant
output relays are other example of control
reliability design. If one relay fails, a second is
used to stop the guarded machine. Figure: Light curtain model from Omron
17. Light curtain applications
• Light curtain applications are often grouped
by the type of guarding required. Guarding
for the point of operation, also called the
zone of hazardous operation or the pinch
point, protects and operator from the hazards
located where the process is performed.
Finger and hand protection is the primary
goal for light curtains used to guard presses,
stamping, forming and automated assembly
machinery.
• Perimeter guards are used to guard the
boundary defined by a machine or robot. The
goal is to detect the presence of humans and
to control the machine to prevent hazardous
conditions while personnel are present in the
area. Perimeter guarding applications are
usually designed to detect arm and body
elements. The entrance to the robot cell in
Figure is guarded by a horizontal light curtain.
17
Figure: Robot Work Cell Guarded
by a Horizontal Light Curtain
Figure: Automatic Drilling Machine
Protected by a Vertical Light Curtain
18. Calculating Safe Curtain Distance
One of the most important concepts related to the use of light curtains in machine guarding is the
calculation of the minimum safe distance. The ANSI standard B11.19-1990 (4.2.33.3.5) describes the safe
distance as:
The ANSI minimum formula is:
Ds = K * (Ts + Tc + Tr + Tbm) + Dpf
where
Ds = Minimum safe distance.
K = Hand speed constant in inches per second. The ANSI standard value is 63 inches per second.
Ts = The stop time of the machine in seconds measured from the final reenergized control element.
Tc = The response time in second, of the press or machine control circuit to activate the machine’s
brake.
Note: Ts + Tc are usually measured together with stopwatch.
Tr = The response, in seconds, of the safety light curtain. Use the value of 0.045 seconds in planning
an installation or use the actual response time of the light curtain provided in the installation
manual.
Tbm = The additional stopping time, in seconds, allowed by the brake performance monitor. If
excessive brake wear is present, a brake monitor will halt the machine when the stop time of
the machinery exceeds the brake monitor limit. Therefore, Tbm = brake monitor set point – ( )
Dpf = The added distance for the depth penetration factor in inches. This compensates for small objects, like
fingers, that can move through a curtain because the curtain’s sensitivity is not sufficient to detect the
presence of the objects. The minimum object resolution S of the light curtain is substituted into the
following equation (S has units of inches):
18
3
.
0
3
.
0
S
Dpf
19. Example 9.1
• A mechanical press has a stopping time for the
press brake mechanism (Ts) of 0.35seconds, and
a stopping time for the control circuits (Tc) of
0.05 seconds. The brake monitor is set for 0.49
seconds. The response time of the light curtain
selected is 0.045 seconds and the minimum
object sensitivity (S) is 0.80 inches. Determine the
safe distance Ds for the curtain to be mounted
to the press.
19
20. Solution
K = 63 in/s (chosen)
Tlim = brake monitor setpoint – (Ts + Tc)
= 0.49 s – (0.35 s + 0.05 s) = 0.09 s
Dpf = (S-0.3) / 0.3 = (0.8 in – 0.3)/0.3 = 1.67 in.
Ds = K x (Ts + Tc + Tt + Tbm) + Dpf
= 63 in/s x (0.35 s + 0.05 s + 0.045 s + 0.09 s) +
1.67 in.
= 33.705 in + 1.67 in = 35.375 in.
20
21. Pressure Sensing Mats
• A pressure sensing mat is a simple solution to many safety issues associated with
sensing the presence of humans in an area. The full visibility and access to the
work area offered by mats is their primary advantage. Another advantage is their
simple mode of operation.
• Sensing Mat Operation
• The electrical model for a mat is a normally open switch that closes when a
specified minimum weight is applied to the mat. The guarded machine is halted
by the mat control system when the system senses that the mat switch is closed.
The mat switch is formed by two conductors separated by small insulators. Each
conductor is connected to a pair of wires that are used to interface to the control
circuits.
• The mat components are molded into a PVC structure to create a strong
assembly. The resistance of the mat switch circuits falls to zero (a closed switch)
when pressure is applied to the active mat area. This switch closing in the mat
causes a relay in the mat controller to de-energize. When the mat controller relay
turns off, contacts open and the guarded machine has power removed.
21
22. Pressure Sensing Mats (cont.)
• Mats are available in various sized and can be linked
together by joining strips to provide presence sensing for
a large area. Mat controllers permit multi mat layouts to
be combined electrically for a single machine stop
signal when any mat in the group receives the minimum
force. Mat controllers offer the following safety features:
• Control reliable circuitry.
• Corroded-mat electrode monitor.
• Mat-wiring integrity monitors.
• Remote access to status, test, and reset functions.
• Built-in diagnostic indicators.
22
23. Interlocking Devices
• The safety interlock switch is one of the most
important types of protective devices because it
interlocks the machine guard door with the power
source of the machine. When the guard door is
opened, the power to the machine is removed,
which ensures the safety of the operator. There are
many different types of interlock switches, and it is
important to select the device type that matches
the application. The general features and
requirements of switches used for interlocking duties
are described in the following sections.
23
24. Interlocking Devices cont.
• Interlock Switch Operation
The European Standard EN 1088, interlocking devices associated with
guards, and EN-60947-5-1 from electromechanical switches are used
to design interlocks in robot and machine safety situations. The first
requirement of interlocks switches is reliable operation under extreme
conditions and rough treatment.
A second requirement relates to security. The interlock switch must be
able to overcome all attempts to cheat or defeat the mechanism.
Personnel often attempt to override an interlock switch to expedite
an order or to save production time. Machine usage information
gathered at the risk assessment stage of the design process will help
to determine if cheating is likely. Switch security levels range from
resistance to impulsive tampering to being almost impossible to
defeat. Interlock device that are not accessible when the guard door
is open provide the highest degree of security.
24
25. Interlocking Devices cont.
25
Interlock Positive Mode Operation
The standard defines positive mode as the movement of one object by another through direct
contact or via rigid elements. In single mechanical type interlocking switches, the movement of
the guard and the switch safety contacts exhibit positive mode operation, This ensures that the
contact physically pulled apart or force disconnected by the movement of the guard, and that
the contacts do not rely on spring pressure to open. This feature, required by the standard,
overcomes the problem of sticking or welded contacts or a weak or broken spring in the switch.
Figure below illustrates negative and positive mode operation.
26. Interlocking Devices cont.
Forms of Interlock Devices
There are two basic types of electrical interlocking systems:
•Power interlocking – the power source of the machine is directly interrupted
when the guard is opened.
•Control interlocking – the power source of the hazard is interrupted by a power
control device activated by interlock device.
All the current forms of interlocking are illustrated in Figure below:
26
CONTROL INTERLOCKING POWER INTERLOCKING
Without Guard
Interlocking
With Guard Interlocking
Mechanical
Devices
Non-contact
Devices
Unconditional
Guard Locking
Conditional
Guard Locking
27. Interlocking Devices cont.
Power Interlocking
In this technique, guard movement is interlocked directly with the switching of the
power to the machine. This means that the interlock device must be capable of
switching the voltage and current required by the production machine.
This works only with a small percentage of industrial machines because most
machines use a three-phase voltage supply with relatively high current. When high
power switching is required, one approach is to use trapped key system, in which a key
is used to open the guarded area and also to switch power to machine.
The key is trapped in position while the switch is in the on position (guard door is
closed) but can be removed when the guard door is open and the machine is off.
27
28. Interlocking Devices cont.
Control Interlocking
Control Interlocking, the most commonly used method, has an interlock
switch attached to the guard that opens the switch contacts whenever guard
movement is sensed. The interlock switch contacts trigger a control circuit
that removes power from the motor starter or contactor that switches the
primary machine power. Control interlocking can be applied with or without a
physical lock on the guard door.
28
29. Interlocking Devices cont.
Calculating Safe Guard Distance
The draft European standard prEN 999 addresses the distance between protective
guards and the hazards used to overcome the maximum speed an operator would
use to approach a machine. The formula is
S = (K x T) + C
Where,
S = The minimum distance in mm from the danger zone to the opening edge of the
guard.
K = 1600 millimeters per second. Research data indicates that 1600 is a reasonable
assumption for an approach speed by an operator. The actual application might
yield a different value, but as a general guideline, a value for K from 1600 to
2500 millimeters per second is commonly used.
T = The total time in (seconds) from the opening of the interlock switch contact to
the cessation of the hazard.
C = An additional distance in millimeters based on how far an operator could reach
over, around, or through the guard before the stop action of the safety device is
initiated.
29
30. Interlocking Devices cont.
Example 9.2
A robot system has a protective barrier enclosing the work-cell
area. The total time fro the system to come to a full halt after
power is removed is 1 second, and an additional distance of 4
feet is required because of the height of the guard gate.
Determine the minimum distance from the guard gate to the
closed part of the robot work envelope.
30
31. Solution 9.2
Solution:
K = 1600 mm/s (chosen)
T = 1 s
C = 4 ft
C = 4 ft x 304.8 mm/ft = 1219 mm
S = (KxT)+C
= (1600 mm/s x 1 s) + 1219 mm
= 2819 mm
31
32. Interlocking Devices cont.
Mechanical Interlock Devices
Vendors supply another group of mechanical interlock devices that link
movement in the guard door to positive mode switch operation.
There are three main types of mechanical actuation devices:
1. actuator operated
2. hinge operated
3. cam operated
The actuator operated device, the most common mechanical safety
switch, has an actuator tongue mounted to the guard gate. When the
gate is closed, the tongue slides into the switch and closes the switch
contacts. The contacts open when the tongue is pulled out of the switch
by opening the gate.
32
33. Interlocking Devices cont.
This is an example of this type of mechanical safety switch.
33
Characteristics of this switch
include the following:
Designed to make cheating of
the switch difficult.
Easy to install
Reliable operation
Can be used on sliding, hinged,
and lift-off guards.
Alignment between the guard
and switch must be maintained.
Difficult to clean thoroughly.
34. Interlocking Devices cont.
The hinge operated actuation device in Figure below is mounted over the hinge
pin of a hinge guard door. When the door is opened, the rotation of the hinge pin
inside the switch causes a positive mode operation mechanism to open the switch
include the following:
34
Ideal for hinged guard doors where
access to the hinge centerline is
possible.
Provides protection with only 3
degrees of guard door movement.
Extremely difficult to defeat without
dismantling the guard door.
Wide guard doors have too great an
opening with the 3 degree door
rotation.
Heavy doors can put too great a
strain on the switch actuator shaft.
35. Interlocking Devices cont.
• The cam operated actuation in Figure below is a positive mode,
acting limit switch with a linear or rotary cam. As illustrated, the cam
operator is most often used on sliding guards where the cam forces
the plunger down to open the control circuit contacts when the
guard is opened. Characteristics of this switch include the following:
35
• Small but reliable system.
• Not suitable for hinged or
lift type guards.
• Design must ensure that
cam and guard always
remain in contact.
• Wear on the cam can
cause failure or improper
operation.
36. Human–Robot Cooperation for Handling Tasks
Robots for human augmentation (force or precision augmentation)
stretch from fully automated operation to acting as a servo-controlled
balancer. As an example: in a car drive train assembly the heavy gear box
is grasped by the robot which balances it softly so the worker can insert it
precisely into the housing (see Fig. on next slide).
Preprogrammed virtual walls give the worker a realistic feeling of
constraints. The central interface for the worker’s tactile commands is a
handle equipped with safety switches. These switches trigger the force-
torque sensor that is attached to the robot’s flange. Upon touching both
safety switches (two-handed operation) the force-torque sensor is
activated and the robot control is set to a safe reduced end-effector
speed (of some 50mm/s).
Thus, the sensor scales the applied force/torque information into a
compliant robot motion. Obviously the physical human–robot cooperation
has to obey safety precautions as the robot’s and worker’s workspaces
overlap.
36
37. Human–Robot Cooperation for Handling Tasks
37
Robot with gripper
Light curtain
Safety switch/handle
Work piece support
Rear axle
Laser scanner (hidden)
Protected area
Fig. Human-robot-cooperation for handling tasks. Inside a regular workcell which is secured by light
curtains, the robot handles gear boxes at regular speed in fully automated mode. Upon approaching the
light curtain at reduced speed, the worker grasps the safety switch which activates both the reduced-speed
mode and the force-torque sensor. The worker guides the robot almost effortlessly by its handle so that the
gear-box is balanced with precision into the rear axle frame for final assembly (Fraunhofer IPA, Stuttgart)
38. Human–Robot Cooperation for Handling Tasks (cont. 1)
The ISO standard specifies requirements and guidelines for the inherent safe design,
protective measures, and information for use of industrial robots. It describes basic
hazards associated with robots, and provides requirements to eliminate or
adequately reduce the risks associated with these hazards. A novel element of this
revised standard is the regulation of so-called collaborative operation, where the
robot works in direct cooperation with a human within a defined workspace.
Basically the collaborative operation depends on several criteria, which have to be
met by the robot work cell:
1. The hand-guiding equipment shall be located in the area of the end-effector.
2. The robot moves with safe reduced speed (less than 250mm/s) and safe monitored
position. This position monitoring shall be according to at least category 3 of ISO
13849, unless a risk assessment is performed and determines that a higher category is
required.
3. The robot must sense and keep a safe distance from the human. The distance
relates to the attended speed. The distance and speed monitoring shall be
according to at least category 3 of ISO 13849, unless a risk assessment is performed
and determines that another category is required.
38
39. Human–Robot Cooperation for Handling Tasks (cont.2)
If a robot’s total power consumption can safely be limited to 80W as well as its
static impact forces to 150N no additional sensor-based safety precautions are
needed. Again, these conditions have to be secured by a risk assessment or
security systems which comply with at least category 3 of ISO 13849. Currently,
novel control algorithms, kinematic and actuator designs are being
investigated to realize so-called intrinsically safe robots.
The described workcell complies with the ISO standard in such a way that the
presence of the human is detected by activating both safety switches of the
handle (first condition). The robot’s built-in safe controller safely measures the
end-effector’s position and limits its velocity(second condition). Meanwhile
most of the robot manufactures provide safe category 3 controllers. If the
worker’s presence in the workspace is not known (third condition, not
applicable here) a safe sensor system has to detect safely the workers location
according to category 3. Three-dimensional sensors meeting category 3 first
appeared on the market in 2006, thus opening up a wide field of potential
collaborative operations.
39
40. Safeguarding the Operator
• The standards state that the operator safeguards
should:
1. Prevent the operator from being in the work
envelop when the robot is executing a program, or
2. Prevent robot motion when an operator is present in
the work space.
• In addition, the operator training should prepare
the operators for thee hazards associated with the
programmed robot tasks, so they can recognize
them and respond appropriately.
40
41. Safeguarding the Programmer
• The standards state that a person programming robot operations or
teaching location points should have the necessary training for the
programming application, check that hazards do not exist, verify
that all safeguards are in place and working, and leave thee work
envelop before initiating the run mode.
• When the teach mode is used:
1. The robot system and other equipment in the work envelop must be
under the control of the programmer
2. The robot system can operate at high speed under only special
operational conditions, and
3. No robot motion can be initiated by remote interlocks or external
signals.
• Finally, only the programmer is allowed in the robot work space
when the robot is in the teach mode.
41
42. Safe Guarding Maintenance and Repair Personnel
• The standards address the maintenance of the robot in both the
power-up and power-down modes. Rules are provided for the
training of maintenance personnel, in addition, rules to cover entry of
the work envelop and maintenance of o robot under power are
listed.
• Since safety consciousness begins with the individual worker, the
following guidelines should be emphasized to each worker:
• Rule 1: Respect the robot. Do not take the robot for granted or make
an assumption about the next movement the arm will make.
• Rule 2: Know where the closest emergency stop button is at all times.
• Rule 3: Avoid locations in the robot work cell between the robot arm
and fixed objects like metal posts or production machines (These
types of locations are called pinch points).
• Rule 4: Know the robot. Pay attention to unusual noises and
vibrations from the machinery.
42
43. • Textbook:
1. James A. Rehg: Introduction to Robotics in CIM
Systems. Fifth Edition, Prentice-Hall. 2003.
•
• Reference book:
1. Mikell P. Groover: Automation, Production Systems,
and Computer Integrated Manufacturing, Second
Edition. 2004.
2. Mikell P. Groover, Mitchell Weiss, Roger N. Nagel,
Nicholas G. Odrey: Industrial Robotics: Technology,
Programming, and Applications, McGraw-Hill. 1986.
3. Farid M. L. Amirouche: Computer-Aided Design and
Manufacturing. Prentice-Hall.
4. Richard K. Miller, Industrial Robot Handbook. Van
Nostrand Reinhold, N.Y. (1987).
43
TEXT AND REFERENCE BOOKS