Cheap Rate ➥8448380779 ▻Call Girls In Iffco Chowk Gurgaon
Foosball table-diy
1. instructables
Foosball Table DIY!
by v1nce_nt
For those of you with video memory, put your sound on and check out the link above. For those with picture
memory, enjoy the read! Or enjoy both;)
https://www.youtube.com/watch?v=Y5AwdPQd0iQ
Step 1: Planning
I got these specs from a ''Tornado'' table because I wanted to make it as close to regulation size as possible. And
since regulation sizes usually vary, I know that the ''Tornado'' tables are used in competitions very often so I went
with them.
Foosball Table DIY!: Page 1
2. Step 2: Ready Your Materials
To start out, I layed out all the wood I was going to use. I used pine for most of the project. Pine walls, pine
plywood. The legs were cut from oak, and the handles were carved on the lathe from maple.
Step 3: Cut Em Up
When making a wide board, it's best to glue small pieces into one instead of using a whole board. This will later
minimize curves and bends in the workpiece when humidity changes. So I cut up my wide pieces on my old table
saw and planed the edges for a smooth and straight result.
Foosball Table DIY!: Page 2
3. Step 4: Glue
Once everything was cut up, I got gluing. Everything here is pretty self explanatory. Once the glue dried, I used the
planer to smooth everything out.
Foosball Table DIY!: Page 3
4. Step 5: Routing
Now to attach the boards to the plywood, there's quite a few options, but I went with the routed trench option. I
think this is the most simple option if you've got a router. So I routed out a trench width to the thickness of the
plywood board on all four wall boards, all equal distance from the top.
Step 6: Fit
I fit it all together to see how it all came together. I was genuinely satisfied with the results!
Foosball Table DIY!: Page 4
6. Step 7: Goals
I then drew out a square for the goals and cut them out with the jigsaw. I tried to cut as straight as possible since I
wouldn't be able to get my sander into the opening and would have to fix the imperfections by hand sanding. After
cutting the goals out, I also cut out an opening for the ball drop hole. Which I then traced with the router to round
out the edges.
Step 8: Cover Board Cut-out
This step is also optional since you can build your table any design you'd like. For my table, I wanted the whole
table to be flush and square. So I decided to cut out this ''down-stair'' to later set my cover board on top of. This
way it would be flush with the top of the whole table.
Foosball Table DIY!: Page 6
7. Step 9: Making the Legs
So I got four long oak logs and cut/planed them
square on the table saw. But in this step also lies a
small design problem. The oak that I used was only
outdoor-dried. So it wasn't very dry at all. Also, I cut
the rectangular legs from the center of the logs.
Which means that the heart of the wood was used.
And when you put these two together, you will get
some cracked table legs once they dry. But that didn't
bother me since that was the look I was going for.
Foosball Table DIY!: Page 7
8. Step 10: Leg Attachments and Finish
When attaching the legs to the table, I didn't want to
use only screws. So I went over to the miter saw and
made two parallel cuts on two sides of the leg about
3cm deep - using a wooden block as a saw
stop/guide. These will rest on two small blocks that
will be screwed to the table and then inserted into the
gaps. This will put less stress on the screws and add
stability to the legs to prevent any play. Once all the
carving was completed, I finished the wood with black
wood lacquer for an old rustic wood look.
Foosball Table DIY!: Page 8
10. Step 11: Mixing the Paint
For the playing surface I was looking for a dark green color. So I took regular water based white paint and mixed it
with a bottle of green pigment and a few drops of black pigment.
Foosball Table DIY!: Page 10
11. Step 12: Painting
I ended up putting about 3-4 coats of paint on to remove as many imperfections as possible and to get the color
tone I wanted. After the paint, I used some polish to give it a shiny finish.
Foosball Table DIY!: Page 11
12. Step 13: More Painting
The inside of the walls were painted a light gray and the goal walls and pocket were all black.
Foosball Table DIY!: Page 12
13. Step 14: Drilling the Holes
Since I don't yet have a drill press in my shop, but needed perfectly drilled holes, I decided to improvise using a
router and its plunge base. I happened to have a 16mm router bit and used it to plunge through the 3cm of wood.
Then I put in a wider diameter bit and drilled half way into the same holes. This is so I can attach bearings
sometime in the future if I so desire.
Foosball Table DIY!: Page 13
14. Step 15: Duplicate the Holes
Once one board was finished, I took the other board and lined them up, clamping them together. I marked the
openings with a 16mm feather drill bit. Then I removed the top board and repeated the routing process following
the markings. Once that was all done, I painted them.
Foosball Table DIY!: Page 14
15. Step 16: Handle Grips
I used the lathe to carve out the maple handle grips. I made them all at once and then cut them up instead of
making them all one by one. Then I drilled a 16mm hole in them and this part got pretty smokey since maple is
pretty hard. Then I did a bit of sanding with the company of my dog:) And I used the same black lacquer on these
to match the legs.
Foosball Table DIY!: Page 15
16. Step 17: Attach the Hand Grips
To attach the handles, I used a type of glue that apparently glues about everything. This is my first time using the
glue so I'm not sure how long it'll keep its hold but so far it's holding on pretty good. If later it gives out, I'll use
screw or pins to secure them.
Step 18: Assemble the Walls and Legs
Now I was finally ready for assembly. I attached the field walls to the playing surface first. I used thick furniture
screws for durability. I also assembled the legs, sliding them into their pockets and fastening them with screws
from 3 sides. So that's 5 screws, since 1 side got 1 screw and the rest got 2. ''They ain't goin no where!''
Foosball Table DIY!: Page 16
18. Step 19: Slide in the Bars and Players
Now the table was on its legs and I was ready to
attach the players. I slid in the bars in their correct
order with four handles on each side. And also slid in
the players in their correct order:
Team 1 -------------I--------------
Team 1 -----I----------------I-----
---I---------I----------I--- Team 2
Team 1 ----I----I----I----I----I----
----I----I----I----I----I---- Team 2
Team 1 ---I---------I----------I---
-----I----------------I----- Team 2
-------------I-------------- Team 2
Step 20: Attach the Player
It's important to get the measurements correct
between the players (check step 1) and once you're
ready, screw in a hole in the bar the size of your bolt.
Attach the nut from the other side and tighten. The
boards in the pictures don't mean too much, I just
used them to help keep the players in place instead
of having them slide around. I also used it to suspend
the bar so that when I put pressure on it from the
drilling, it wouldn't bend. You can do this without the
boards, just need to be a little more careful.
Foosball Table DIY!: Page 18
19. Step 21: Cut the Bars
When I was buying the bars, I bought them all 1.5m
long. You don't need all this length because the
longest bar you'll need is about 1.2m. But I just
decided to get extra just in case. So since my bars
were longer than needed, I went ahead and cut them
to the correct distance with my jigsaw. But be careful
not to cut too much! Before you cut, make sure you
push in the side that you are cutting all the way in,
away from yourself, and cut about 2-4cm out from the
wall . If you do the opposite, you'll cut too much and
scrap the pipe!
Foosball Table DIY!: Page 19
20. Step 22: Drop Hole
For the goal drop hole, I cut out 3 pieces of plywood to their correct width and height - the height matching the end
board. Painted them dark, and slid them in between the boards, and attached them with a few nails. You really
don't need much to hold them in place. They won't be receiving any pressure or use.
Step 23: Put on the Cover
And now to cover up all those internals, I slid a pine board on top and screwed it in place. I then coated it with
white lacquer (as I did with the rest of the table) and I was all done!
Foosball Table DIY!: Page 20
21. Step 24: Final Product
I hope you enjoyed this build and were motivated to
build one yourself! It's definitely a great toy to have
around the house (if space allows). It's especially
great since it's fun for all ages from kids to the elderly.
Of course, you could save yourself a bunch of time
and go buy one that's already built and ready to go,
but you'll be missing out on the adventures of building
and designing your own. Plus you could probably
save yourself a few bucks. Anyway, thank you for you
time, and let me know if you end up building one!
Foosball Table DIY!: Page 21
23. I haven't played foosball in forever! What a fun game and build. Thanks for sharing :)
It sure is! Glad you enjoyed:)
Great instructable. I built one of these many years ago. A few things that I did differently were; put
springs and rubber washers on the pipes between the handles and the walls to save wear and tear
on the walls, put a board in each corner starting at nothing and sloping up to 3/8 inch so that the
ball won't get stuck in the corner, and put a 45 degree board inside the goal so the ball doesn't hit
the back and bounce right out again.
I did include rubber washers, if you look closely, you'll see them, they're just not too nice, but they
do protect the wood ok. I'll probably end up installing springs and nice washers in the future. Along
with bearings and maybe also make a score counter. But the ball getting stuck in the corner is a
problem that I didn't think I'd have, and I've thought about making a slope. Or maybe I should just
stick two more players in those corners? And that 45 degree board inside the goalie idea is cool, I'll
probably actually go do that right now:) or what if I stuck a piece of thick foam back there? I feel
like that would work just as well.
Yeah, the foam is a great idea and would probably work better. With the boards in the corner, you
have to sand down the edges to almost nothing because if the ball is going fast, it flies right out of
the game when it hits an edge.
Haha, that's true, I didn't even think of that.
Foosball Table DIY!: Page 23