HSIL CD-II (1)

HSIL Ceramic Division-II 2
SUMMER INTERNSHIP
HINDUSTAN SANITARIES&INDUSTRIES LIMITED
HSIL Limited (Formerly Hindustan Sanitaryware & Industries Limited) is the
flagship Company of the Somany Group and was established in 1962 with a
joint venture of the Group with Twyfords, UK.
HSIL Limited is the largest Indian manufacturer of Sanitaryware products with
a dominant market share of 40% in the industry. HSIL Limited products are
available across the length and breadth of the country and are supported by over
1000 direct dealers and 12000 sub dealers HSIL Limited was the first Company
in India to manufacture Vitreous China Sanitaryware.
HSIL Limited’s installed capacity of 600 tonnes /year at the time of inception
has now reached 32000 tonnes/year (2.8 million pieces /year). This is an
outcome of significant expansion and modernization at Bahadurgarh Plant,
acquisition of Krishna Ceramics Ltd. at Bibinagar in 1989 and its merger into
HSIL Limited (Ceramic Divn.II) followed by extensive modernisation and
expansion.
In sanitaryware, the company has the largest kiln of its kind - 110 metres long,
5.5 metres wide, open-flame microprocessor-controlled, and one of the most
energy efficient kilns in the world. The company extensively uses battery
casting for the highest productivity in sanitaryware in the country.

SUMMER INTERNSHIP
ACKNOWLEDGEMENT
The internship opportunity I had with HSIL was a great chance for learning and professional
development. Therefore, I consider myself as a very lucky individual as I was provided with
an opportunity to be a part of it. I am also grateful for having a chance to meet so many
wonderful people and professionals who led me though this internship period.
Bearing in mind previous I am using this opportunity to express my deepest gratitude and
special thanks to the Mr. SWAMINATHAN, AVP of HSIL, CERAMIC DIVISION-II for
giving me this wonderful opportunity to undergo internship training at this esteemed
organization.
I express my deepest thanks to Mr. ANIL, HR at HSIL for taking part in useful decision &
giving necessary advices and guidance and arranged all facilities to make life easier. I choose
this moment to acknowledge his contribution gratefully.
It is my radiant sentiment to place on record my best regards, deepest sense of gratitude to
Mr. S.LAKSHMI NARAYANA (Slip house & Mill house)
Mr. V.L.N MURTHY (Moulding & Casting)
Mr. VIJAY KUMAR (DGM, PRODUCTION)
Mr. RAMAKRISHNA (Glazing)
Mr. VENKATA RAMAIAH (Kiln)
Mr. NEERAJ KUMAR SHARMA (R&D LAB)
For their careful and precious guidance which were extremely valuable for my study both
theoretically and practically. And also my sincere thanks to all the executives, supervisors
and workers for their cooperation.
I perceive as this opportunity as a big milestone in my career development. I will strive to use
gained skills and knowledge in the best possible way, and I will continue to work on their
improvement, in order to attain desired career objectives. Hope to continue cooperation with
all of you in the future.
Sincerely,
T MAHESH NAIK

SUMMER INTERNSHIP
INTRODUCTION
Sanitary ware is a division of ceramic wares. It is proven that ceramic sanitary ware wares
are cost effective and good for long run. They are considered to be extremely durable as well
as hygienic. Sanitary wares can with stand more than 400 kg load and excellent resistance to
chemical attacks. Sanitary ware items can be easily cleaned because of its glossy surface
properties. Sanitary ware items are made up of ceramic ware that used in bathrooms. Some
of the sanitary ware products are toilets, washbasins, pedestals, bidet, urinals, sinks, bath
tubs, etc..,
Sanitary ware Meaning: Sanitary – Hygienic and Clean.
Ware – Product / article
Process of Manufacturing:
Sanitary wares are consisting of two types of mixtures of different raw materials. The first
type is called body and the other type is called glaze. The body is mainly a tri-axial
compound i.e. made of clay, quartz & feldspar. On the other hand the glaze is made of
different oxides pertaining to different colors including the basic raw materials of clay, quartz
& feldspar etc. For body making the raw materials like china clays, ball clay, quartz, feldspar
etc. are mixed with water thoroughly to get a uniform slip. They are unloaded in an agitator
i.e. blungers. The slip is screened, magnetic separated and kept in an agitating tank with
addition of required deflocculants. The wares are cast in plaster moulds. The cast wares are
hard felted and kept on open racks or benches for drying and sent for driers for further
drying. The dried wares are tested for cracks and then finished. On the other hand glaze is
prepared in similar way by ball milling, screening and magnetic separation and then the glaze
is used in spray booth to apply on the finished dry body products and the glazed body is sent
for drying & then firing. After firing the fired products are sorted out and packed for sale.
Sanitary ware manufacturing / production process consists of 10 steps from slip preparation
to Packing. They are
1) Slip preparation
2) Glaze preparation
3) Modelling & Moulding
4) Casting
5) Drying
6) Inspection & Spraying
7) Firing
8) Sorting
9) Re fire/Rework
10) Packing

SUMMER INTERNSHIP
PRODUCTION FLOW CHART:
Production
Drier
Mill House Department
Casting Department
Moulding/Block making/
Modelling Department Inspection & Glazing
Slip House department
Placing/Kiln Department
Quality Assurance Department
Ware House Department
Re-fire Department

SUMMER INTERNSHIP
CONTENTS OF THE REPORT
1. SLIP HOUSE
2. MILL HOUSE
3. MODELLING & MOULDING
4. CASTING
5. INSPECTION & GLAZING
6. KILN
7. LABORATORY

SUMMER INTERNSHIP
SLIP HOUSE
In Sanitary ware Manufacturing/Production process slip preparation is the first step. In this
process Slip is produced by mixing ball clay, silica, china clay and feldspar. This
composition is called Tri-axial body. Consist of Body former, Filler and flux. Body former is
plastic material which is required to give strength at the green stage of the sanitary ware.
Filler is non-plastic material which is going to give strength after the firing. Flux is a non-
plastic material which added to the body to reduce the fusion temperature point of the body
during firing. All raw materials are mixed at proper position and brought to required physical
parameters.
Normally following rheological parameters are checked after slip preparations – Fluidity,
Thixotropic of the slip at 1 minute and 5 minute, Half-Liter weight and casting rate.
These parameters will vary depending upon the composition, climate, type of casting and
required casting rate.
Supply slip will be mixture of virgin slip, run off slip & scrap slip. This composition also will
vary according to the availability of the scrap slip available and required casting rate.
Once slip prepared according to the required parameter it will be sent to slip storage tanks.
Whenever slip is required then it will be supplied to casting department for casting.

SUMMER INTERNSHIP
Roles and Functions of Ceramic Raw Materials in the Sanitaryware Body:
Ceramic raw materials are usually classified according to their functions in ceramic
manufacture as well as their basic properties. It generally divides the ceramic raw materials
in two basic groups that are the plastic and non-plastic raw materials. Further detail division
depends on the material composition.
Plastic ceramic raw materials involve any clay material that when mixed with water reveals
the property called plasticity. Plasticity may be defined as a property which allows the
deformation of the clay when an external force is removed. A part of the non-plastic ceramic
raw materials acts as a filler, reducing high plasticity or shrinkage of the body when drying
or firing. On the other hand, other non-plastic raw materials are used for fluxing and melting.
The classic or "triaxial" ceramic body consists of three major components: clay (plastic),
quartz which is a non-plastic material and feldspar, that acts as a flux providing the glassy
phase. Typical raw materials normally used in a sanitaryware are clay, feldspar and silica.
Sanitarywares are thus referred to as triaxial bodies, owing to the three mineral types—
clay, silica and feldspar—consistently found in their makeup. Clay is the plastic component,
giving shaping abilities to the unfired product. Silica serves as a filler, lending strength to the
shaped body before and during firing. Feldspar serves as a fluxing agent, lowering the
melting temperatures of the mixture.
Clay:
Clays are formed by alteration, through aging and weathering of rocks such as granite,
feldspar, mica and quartz. At the origin, they are known as residual or primary clays. The
clays are formed at the site of the parent rock and are not transported by any of the various
agencies such as wind and water. Primary clays like china clays are usually found in irregular
pockets with unaltered rocks remaining. Primary clays are normally uncontaminated by non-
clay minerals as most of the primary clays originated from pure feldspar. Most kaolins are
primary clays. The fired color of the china clay is white as it has a high degree of purity.
Therefore, it is suitable for manufacturing sanitaryware. In addition, it is refractory due to its
low impurity content.
If the clays are transported by wind or water from their original point of formation, they are
known as sedimentary or secondary clays. The action of the water tends to grind up the clay
into a much smaller particle size. Sedimentary clays such as ball clays depend on their fine
particle size for remaining in suspension whilst they are being transported. This process of
sedimentation separates the coarse from the fine and only the very fine particles will be
carried to the final deposit. The sedimentary clays are likely to be contaminated with
impurities or accessory minerals that are picked up along the way such as muscovite, quartz,
iron oxide, rutile and garnet. Transported clays are usually made up of clay from various
sources. Sediments from numerous sites are likely to be mixed together with the presence of
carbonaceous matter. Secondary clays are therefore fine-grained and plastic. The fired colour

SUMMER INTERNSHIP
is normally more buff than china clay that is usually white. The presence of organic and other
impurities as they were re-deposited in low lying swampy areas may be the root cause of the
darker fired colour. The ball clays are mainly kaolinite but they are much finer than china
clay and the impurities present are also very fine as well. Thus china clay needs less
deflocculants and water, whereas ball clay needs more deflocculants (as more impurities) and
water. Therefore a mixture of both the clays is used in sanitaryware production for desired
characteristics of the body.
The ball clay is the most difficult to disperse and is, therefore, normally processed and
allowed to age prior to final casting slip preparation.
Feldspar
Feldspar is an important and common fluxing material for ceramic bodies as well as glazes
and one of the three essential raw materials for the tri-axial body. Feldspar provides the
glassy phase for the ceramic bodies and they are added to decrease the firing temperature and
thus to reduce cost. It gives white color to the body.
Feldspar play an important role in achieving the vitreous nature of the body and the high
mechanical resistance of the product at the end of the firing stage. Due to the formation of
liquid at early stages it fills all the pore spaces and the body becomes non-porous (vitreous).
Silica
Silica is the most abundant oxide on the earth's crust. Silica as compared to the other raw
materials in the ceramic bodies is relatively cheap. Silica sand is used in the slip as a source
of silica. Addition of silica sand decreases its unfired strength and plasticity. It also reduces
drying shrinkage and increases the whiteness of the fired body. It also gives good strength to
the body.
One of the great advantages of the tri-axial composition is that it makes the formed piece
relatively insensitive to minor changes in composition and in firing time or temperature. This
stability is a result of the wide range of temperatures over which the three ingredients melt to
form glass.

SUMMER INTERNSHIP
SLIP -HOUSE PROCESS FLOW CHART:
Batch weighing
Batch raw materials loading in Blunger
After required homogeneous mixing
Blunger Addition (water + electrolyte)
Sieve & Magnet
Virgin slip stored in tank
Slip Properties Test
Supply slip preparation (Virgin + Runoff
+ Scrap)
Send to casting
Supply slip properties test
Raw Materials

SUMMER INTERNSHIP
Preparation of slip in slip house:
Ball mills are used for grinding the silica sand and pitcher materials. The raw materials are
stored in different storage chamber. The loaded ball clay raw material is supplied from
hopper to cart and then discharged into blungers. The slip from blunger is supplied to tank
after getting sieved in vibrating sieve (#140mesh).In these sieves magnets are there for
removing the iron particles in slip.
Then that slip is sent to a storage tank. The quartz sand is grinded in ball mill for 6-8 hours.
The china clay is also added to quartz sand for easy unloading. After grinding the quartz
sand, the slurry is stored in another tank. The ball clay slip and quartz sand slip are sent to
measuring tank. From measuring tank, sent to blunger. Now china clay is loaded in hopper
into carts. And from carts added into blunger directly. Now feldspar powder is added directly
in to the blunger. Required amounts of deflocculants is also added. This prepared slip is
called “virgin slip”. This virgin slip is stored in another storage tank.
Scarp slip
Scrap means rejected green and dry wares.These scrap materials are brought from
casting points and inspection booths. These scrap materials mixed properly in blunger with
sufficient water. And barium carbonate is added as deflocculant. The deflocculant is used for
free flow of slip.
Run off:
The run off slip is collected from casting points. The slip unloaded from moulds after getting
required thickness is called RUN OFF SLIP. This slip is also stored in storage tank.
Mixed slip:
It is the combination of scrap, run off and virgin slip. In measuring tank the slips are taken
according to their composition. Now from measuring tank it is to supply tank after
sieving on vibrating sieve (#100mesh) with magnetic separator. The magnets are used for
removing iron content in slip.
The scrap, run off and virgin are mixed according to following composition.
Run off - 60 %
Virgin - 26 %
Scrap - 14 %

SUMMER INTERNSHIP
Consistent behaviour of the slip is important in minimising day to day production problems.
Such consistency is essential for the setting of factory production rates which achieve the
most efficient and cost effective manufacture of the finished ware.
SLIP CONTROL:
The most widely used method of casting slip control is based on the measurement of fluidity
and thixotropy by means of a Torsion Viscometer which is simple to use, robust and
relatively low in cost. The results it produces are quickly available and easy to interpret.
Necessary adjustments can be made rapidly to casting slips and re-measurement of fluid
characteristics takes only a few minutes.
MEASUREMENT OF FLUIDITY:
Before taking a measurement of fluidity, the viscometer cylinder is wound through 360
degrees in anti- clockwise direction. With the viscometer beaker in position under the
viscometer, the flywheel pin is released hereby enabling the flywheel to rotate in a clockwise
direction.
The over-swing indicated by the pointer on the flywheel against the graduated scale is
recorded as a measurement of fluidity.
It is important to ensure that the sample of slip is thoroughly stirred immediately prior to the
actual measurement.
Samples taken from production blungers are stirred in the viscometer beaker for exactly one
minute, immediately placed into the measuring position and readings are taken after 5
seconds (it is critical that the time is kept constant to ensure consistent, reproducible results).
It is also important to ensure that the cylinder is fully immersed in the slip being measured.
MEASUREMENT OF THIXOTROPY:
Thixotropy, or the tendency of an undisturbed slip to thicken with time, is an important
property which has a marked effect on casting performance. It is measured by rewinding the
viscometer flywheel immediately after taking the fluidity reading, allowing the slip to stand
undisturbed for 60 seconds, and then re-measuring the over-swing.

SUMMER INTERNSHIP
Thixotropy is defined as the difference between the two readings. In some instances, a 5
minute thixotropy reading is also useful.
It is important that the temperature is recorded as temperature can severely affect viscosity
values.
MEASUREMENT OF SLIP DENSITY:
The density of a casting slip is kept within defined limits as variations will affect casting
performance. A low density slip can result in the difficulties with second casts and mould
drying. Conversely, high density slips can lead to casting and pouring difficulties if particle
packing and fluidity parameters are not controlled well.
The measurement of slip density is quite simple. A pre-weighed vessel is filled to a
calibration mark of 500ml and then weighed. The difference in weights represents the weight
of a slip in a given volume. Density of casting slip is expressed in g/cm3.
THE CONTROL OF CASTING SLIP:
It is necessary to specify slip control values which will depend on both the body being used
and the type of ware being produced. The best method of arriving at these values is to
monitor the fluid properties and density of the slip, and then to compare these observations
with casting performance over a period of time. It then becomes possible to relate fluid
properties to casting performance.
This is extremely important in systems as there is a re-use of run-off slip and reconstituted
scraps mixed with virgin slip.
Most casting slips perform satisfactorily when set to a fluidity of between 290 - 310 degrees
overswing and a one-minute thixotropy of between 40-50 degrees, at a density of between
1.7600 to 1.7800 g/cm^3.
To achieve a fluid casting slip, at a suitable solids loading, the clays have to be deflocculated.
A mixture of sodium silicate and sodium carbonate is used, as this system is not too difficult
to adjust. The casting slip control system is most easily understood by knowing how fluid
properties vary with the addition of deflocculant. When sodium silicate or sodium carbonate
is added to casting slip the fluidity increases and the thixotropy decreases. If the deflocculant
is added to excess then a point will be reached where fluidity decreases and thixotropy
increases. This generally serves as an indication of over-deflocculation of the system.

SUMMER INTERNSHIP
Sodium silicate tends to give high fluidity slips with low thixotropy, while sodium carbonate
will give lower fluidity slips with higher thixotropy. It is normal practice to use these two
reagents together as this offers the possibility of obtaining high fluidity slips with an
appropriate degree of thixotropy.
The reagents are mixed in a ratio which will give the most effective control over fluid
properties for the given casting slip system. When this mixture is used, a progressive addition
of deflocculant will increase fluidity to a maximum and further additions will have little
effect on the level of fluidity. Thixotropy, however, will decrease steadily as deflocculant is
added and will continue to do so even after fluidity has levelled off. In this way thixotropy
can be adjusted while fluidity is maintained.
If the maximum value of fluidity is too low, then the density of the slip may be reduced by
the addition of water. This will have a marked effect on fluidity, but only a slight effect on
thixotropy. The density of the slip will not need to be drastically reduced as a small decrease
in density results in a large increase in fluidity. The aim of slip control is to keep the density
as high as possible whilst maintaining acceptable fluid properties for effective casting.
AGEING OF SLIP:
Casting slip requires final adjustment prior to use as its fluid properties change with time.
This behavior is the result of the extremely slow rate of reaction between the various
deflocculants and the clay particles in the body system. The ageing characteristics of a body
will vary depending on its make-up. It is usual to age for at least 72hrs in order to obtain
stability prior to casting.
It is normal practice for casting returns and clay scraps to be reprocessed and used in
Returned slips and scraps contain sulphate ions absorbed during contact with mould surfaces.
If this sulphate is allowed to accumulate in returned and reconstituted slip, it will adversely
affect fluid properties and will also be responsible for other faults which may appear later in
the production cycle.
For overcoming the problem of soluble sulphates an addition at the scrap blunger of barium
carbonate is made. The quantity of barium carbonate required is fairly small as the soluble
sulphate levels are also small. The barium carbonate reacts slowly with the soluble sulphate
to form barium sulphate which is inert and will not react adversely with the casting slip.
After storage, fluid properties may be adjusted with deflocculant in the normal way before
the slip is used in production.
CASTING FAULTS:
It is possible to overcome most casting faults by adjusting the control values of the casting
slip. Below are some of the common faults encountered and suggestions which may be taken
to overcome these faults.

SUMMER INTERNSHIP
If fluidity is too low it may take too long to fill moulds and also there may be difficulty in the
draining of the slip from the narrow sections (poor draining). This can be cured by increasing
water or deflocculant addition
If thixotropy is too low there may form brittle (i.e.hard casts - difficult to fettle) casts, small
cracks and also small uneven fringes on slip side of cast may be formed. This may be cured
by decreasing deflocculant addition or water addition.
If thixotropy is too high, there may be difficulty in the draining of the slip from the narrow
sections and also may result in soft casts which may be difficult to handle. This may be cured
by increasing deflocculant or water addition.

SUMMER INTERNSHIP
MILL HOUSE
Glaze Preparation
In this process glaze is prepared for spraying department. Body preparation and glaze
preparation are parallel process. Different colors of glaze will be prepared according to the
requirement. Raw material of the glaze preparations are zircon, feldspar, quartz, calcite,
china clay, zinc oxide and few more. Raw materials are grinded in ball mill and particle size
is tested before unloaded from ball mill. Glaze will be passed through sieves to remove
coarse particles and magnets to remove iron particles. Sample spraying will be done and fired
to check the final color of the glaze. Glaze should be approved by QA before used in
manufacturing/production. Before supply to the spraying, glaze will be mixed with binder to
give required properties. Density, drying time, fluidity and viscosity are maintained to get
proper spraying. Glazes are formulated as a mixture of ground, powdered ingredients which,
by their nature, do not dissolve but are merely suspended in water.
The following raw materials are used for preparation of glaze:
1. Calcite
2. Quartz
3. China Clay
4. Zircosil
5. Zircolite
6. Zinc Oxide
7. Potash feldspar
8. Soda feldspar
9. Soda ash
10. C.M.C
11. Talcum
Silica is a major glaze component and is added in many forms such as quartz, feldspar into a
glaze. Silica acts as a glass former and is used to control thermal expansion and help impart
acid resistance to the glaze.

SUMMER INTERNSHIP
China clay continues to be the primary suspending agent used in ceramic glazes.
Feldspathic minerals, such as soda and potash feldspar continue to be some of the most
commonly used raw materials. These materials are a major source of alkali fluxes in a glaze
as well as silica. Feldspar can be used as either a flux or refractory material in a glaze
depending on the firing temperature.
Alkaline earth oxide materials such as calcium carbonate, and zinc oxide are generally added
as raw materials. These are advantageous because they provide fluxing action without having
a major effect on glaze thermal expansion.
Zirconium silicate is the major opacifier used in ceramic glazes.
To prepare a liquid glaze (also called a glaze slurry), all of the glaze ingredients are wet
milled in a ball mill. After the glaze slurry reaches the desired particle size, it is passed
through a screen and a magnetic filter to remove any impurities. The density and viscosity of
the glaze are then adjusted to fit the application, and the finished glaze is ready to be used in
production.
PROCEDURE
 The raw materials are taken and batch weighed according to desired proportions.
 Batch raw materials are loaded in a ball mill in which water and binders are also
added.
 After required grinding hours of grinding, the glaze sample is sent for QA
 After approval from QA the batch glaze is transferred through electromagnetic sieve
(to remove any lumps) and then collected in storage drums.
 Subsequently binders are added to the glaze and mixed with shear mixer and is again
sieved and magnetic separation is done.
 Then the glaze is tested for properties and sent for spraying.
The glaze parameters which are tested are half liter weight, fluidity, drying time, residue,
particle size distribution and fired flow.
Binders such as c.m.c i.e Carboxy Methyl Cellulose and peptopon are added. High amount of
c.m.c may affect the drying time of glaze. After adding CMC into the glaze, it will enhance
the bonding & promote the glaze dispersing, and also enhance the adhesion strength of the
glaze and ceramics. As the flow control agent in ceramic glaze and the high-purity CMC
leaves no ash in the process of burning.

SUMMER INTERNSHIP
PROCESS FLOW CHART OF MILL-HOUSE DEPARTMENT:
Raw materials are batch weighed
Batch raw materials loaded in ball mill
Ball mill addition (water + binders)
Glaze sample sent to QA
After required grinding hours
After approval of QA
Batch glaze transfer through electromagnet & sieve
Approved glaze stored in tank
Again electromagnet, sieve & then stored in drums
Binder addition
After binder addition, sieve & electromagnet, then
stored in drums
Supply glaze properties test
Sent for spraying

SUMMER INTERNSHIP
MODELLING
PROCESS FLOWCHART OF MODELLING DEPARTMENT:
Plan received from plant head
Model making
Master mould making
POP block making
Send to casting
Block making
QA Approval
Resin block making
Sent for mould production

SUMMER INTERNSHIP
Normally, requests for new designs are originated by Marketing and Sales in conjunction
with Manufacturing. After agreement has been reached with regard to the basic design
requirements, working drawing are prepared for the Modelling Department. After approval
of the working drawing, a plaster model of the finished size product will be produced by the
Modeller. This model is then inspected by both marketing and manufacturing to ensure that
this is what is required. After approval, the modeller will then model the new article in its
green size, which will be approximately 12% larger, as they contract during the firing
process.
After modelling the article, a “master mould” is produced. This mould closely resembles the
final working mould that will go into production. After completion of this mould, trial casts
are taken from this mould, and these articles, when taken from the mould will be thoroughly
dried, glazed and fired under normal manufacturing conditions. It is standard practice that
several casts will be taken from this mould because it is at this stage that potential problem
areas can be identified, and corrective action can be taken. After final approval of the fired
article has been obtained, a block or case mould, is produced. This case mould is made from
plaster of paris and resins. It is still possible, although difficult, to make minor changes to the
design on the case mould. The negative (master mould) is used to create a positive model
(case). This case is ultimately used to make the working plaster moulds. The plaster moulds
are often made in several pieces to allow complex designs to be manufactured.
In the preparation of blocks iron frames are used for support of the structure. In resin block
preparation few hardeners are used along with sand for the hardening and strength of the
block.

SUMMER INTERNSHIP
MOULDING
In this process required shape and size mould will be produced for casting. All bench and
battery cast moulds used in manufacturing in the sanitaryware industry are made from plaster
of paris. This is a material which is easy to work with and has the advantage that it is
absorbent. All materials provided to the casting departments are in a slurry form, containing a
large proportion of water, the plaster mould will absorb the water from the slip, thus leaving
a semi-hard clay layer on the surface of the plaster mould. The average life of a working
mould is approximately three months or 80 casts and most moulds are only cast once per day.
The moulds themselves may often consist of several pieces, an average number of pieces per
mould is four, although some moulds are much more complex. After producing the moulds
from the 'case mould', the working moulds must be thoroughly dried before being used in
production.
The plaster is hemi-hydrated gypsum. In calcination, the gypsum loses H2O partially and the
crystal structure of gypsum breaks down due to the removal of H2O. While adding water to
the plaster it will then converts in to fine crystals of gypsum. So, while adding water it
changes in to hard lumps.
But for the preparation of mould, the plaster must be converted into slurry, but not hard
lumps. To avoid the formation of hard lumps the proportionate water is taken first and
weighed plaster is dumped in to the water. The plaster and the water ratio are 100:75. While
setting of plaster happens, a reaction occurs between plaster and water which is an
exothermic reaction. In this reaction heat is evolved and it vaporizes the remaining water.
This removal of water causes pores in the mould.
The plaster of Paris is stored in bags in dry atmosphere. This plaster of paris is removed from
bags and dumped in the hopper. This hopper has a normal mesh for avoiding lumps. From
this hopper plaster is moved up through bucket elevator, this elevator is used for transferring
the plaster from hopper to silos. The silos are cylindrical having cone shaped bottom. At the
bottom a screw feeder is provided to discharge the plaster. The screw feeder consists of
screws attached to the shaft. This shaft rotates and while rotating plaster also comes along
with screws and discharges the plaster into drums, placed at the end of screw feeder.
An automatic weighing equipment is provided to control the plaster and water ratio. The
desired proportion of plaster and water is taken to the stirrer. For about 4 minutes, it is
allowed to mixing and the slurry is taken into drums. The block mould is cleaned by using
compressed air, and also wet sponge is applied followed by application of soap solution to
the block mould. Soap solution is used for releasing the mould easily. The male and female
notches and pipes are arranged in required places. Then blocks are set correctly using iron
hoop belts. The plaster slurry which is already prepared is poured into the gap provided
between the top case and block. While pouring the plaster, mould is shaked for uniform
distribution and also for removing air inclusions.

SUMMER INTERNSHIP
After initial setting of the plaster the top case is removed and belt is loosed Because to avoid
the stress created due to the expansion of plaster on setting the mould is allowed for final
setting. After final setting the mould is removed from the block. The compressed air is used
for easy removing of mould. After releasing the mould, finishing is done with a hack saw
knife and sent to drier. Before sending the talc powder is applied to moulds so that they don’t
stick with each other in drier. The moulds are put in drier for 4-5 days at 50 to 60°c
temperature. Then these moulds are supplied to casting points.
The different plasters used in modelling & moulding:
 Plaster:
α Plaster is hemi-hydrated gypsum [CaSo4 ½ H2O]. The α plaster is prepared by the calcination
of gypsum in damp atmosphere. So while adding the water it sets and has very less porous
nature and high mould strength. The plaster : water of this plaster is 100:50 (consistency ratio).
These Alpha Gypsum casts are harder and stronger with limited absorptive power. They are
used primarily when greater strength is required. Because of their extreme hardness some
Alpha gypsums cannot be carved or scraped after hardening. Alpha Hemihydrate is produced
in many different formulations. You can mix an alpha gypsum with a beta gypsum to increase
the plaster's strength or hardness.
 Plaster:  plaster is hemi-hydrated gypsum [CaSo4 ½ H2O]. The  plaster is prepared by
the calcination of gypsum in open atmosphere. While adding the water it has comparatively
slow setting, high porous and less mould strength. Beta Hemihydrates are known as industrial
plasters. They require more water to make a workable slurry because of their irregular
crystalline structure. They require 100:75 ratio of plaster to water (consistency ratio). Beta
Gypsums are not as hard as the alpha gypsums. That's why they are easier to carve and scrape.
Because of their high water absorptive power, they make excellent pottery molds.
Thus α plasters are used in block making for its strength and β plasters are used in casting of
moulds for good water absorption.

SUMMER INTERNSHIP
CASTING
It is a process, in which slip (a water-based suspension) is poured into a plaster mould, which
by its porosity creates capillary forces and removes liquid from the suspension (slip). When
the liquid is absorbed into the plaster mould, the powder particles are forced towards the
mould walls and a consolidated layer is gradually built up. When a desirable layer thickness
has been obtained, the casting process is stopped either by having the excess slip removed, or
by letting the casting fronts approach each other in the centre of the piece to form a solid
body. After a certain period of drying the shaped piece can be released from the mould for
further drying. The advantages of slip casting as a forming method are mainly that complex
geometries can be shaped, and good material homogeneity is generally achieved.
There are mainly two types of casting:
 Solid casting: Casting proceeds until the casting fronts approach each other and a
solid body has been obtained.
 Drain casting: When a desirable thickness has been reached the excess slip is
removed.
The process of casting mainly includes slip being poured into the mold and allowed to form
casting layer on the mold. Then the excess slip is drained through drain hole. Now casted
ware is allowed to dry and then released from mold. In this stage the ware is known as green
ware. Few holes are punches in the body using templates This green ware is allowed to dry in
atmospheric temperature for one to three days before sent to drier. Before sending to drier
this green ware is finished to smooth joint edges, repair small cracks, small pin holes, bad
finishing and etc. once this ware is ready it will be sent to drier for drying.
Bench Casting:

SUMMER INTERNSHIP
It follows the concept of drain casting. In this casting method the moulds are arranged on the
benches and hence called bench casting, since casting is done on the benches. Before casting,
we need to make sure it is clean- both inside and out. Debris inside will imbed casting and be
difficult to remove. Debris on the outside can fall into the cavity or the slip. So first cleaning
of moulds is done by using compressed air. After cleaning the conditioning of mould is done
which includes applying water using wet sponge on hollow part of the mould and applying
talcum powder (as lubricant) on the solid parts of the mould for easy release of the casted
piece. Subsequently setting of moulds is done and the moulds are tightened using iron hoop
belts and wooden wedges. Then the slip is poured into the moulds manually using pipes
(having mesh at its opening to prevent any foreign material) and also moulds are filled
slowly to remove air inclusions in the slip which may lead to the formation of pin holes.
After the slip is poured into the mold, it is allowed to form casting layer on the mold. Then
the excess slip is drained through drain hole and allowed to dry for some time. After
demoulding required holes are punched into the green body using templates. And allowed for
natural drying for 2-3 days and then sent to the drier after proper finishing.
In this type of casting modifications to moulds can be made with relative ease, small numbers
of pieces can be cast efficiently, and the slip making technology is well established.
However, this method poses several challenges. The process is labor-intensive. Additionally,
significant space is required to produce the ware, making the process capital-intensive. Other
restrictions include a short mould life and a limitation on the number of pieces cast per day.
Battery casting:
It also follows the concept of drain casting. . In this battery casting the moulds are arranged
one by one like batteries. In this casting the moulds are placed on the iron plates which are
having bearing at the bottom. These bearings are used for free movements of moulds. These
bearings are connected to tracks.
Battery Casting line system consists of 2casting benches being aligned at the left and right of
a central slip supply and a central slip return system. The moulds are connected to each other
by means of appropriate distance pieces of plaster or metal and by means of a tightening and
clamping device they are held together at the end of the casting bench.There are 30-45
mobile moulds installed on movable special trolleys and with one end is fixed frame ,while
other end is movable tightening screw trolley. The inclination of complete bench can be set

SUMMER INTERNSHIP
us per required degree of slope. But the moulds are inclined towards the operation side,
which will be emptying all moulds for its return line slip.
Parallel to the casting bench, depositing benches (Storage Racks) are provided at the outside,
serving for depositing the demoulded pieces.
The slip supply of each mould is made by pipeline being attached below the casting benches
and controlled by corresponding valves. Each mould is connected to this pipe system by a
plastic hose and fitted with a shut-off valve. Before filling of the moulds, the slip is allowed
to drain flow for about4-5 min to remove the air inclusions that may be caused due to change
in pressure of flow i.e. allowed to drain unter constant flow is attained. Slow filling causes
thickness variation. So the pressure of the slip is controlled. The mould is filled properly with
slip.
Battery casting offers greater productivity and a relatively low mold cost. Additionally, more
pieces can be produced in the space available, which reduces the capital required for this
method compared to bench casting methods. The skills required to produce ware by this
method are also lower than bench casting.
Battery casting is one type of casting which required less space for more moulds. Battery
casting machines can be used for washbasins, water closets, Traps and other simple
sanitaryware products. Complex patterns like one piece toilets are not suitable for battery
casting. However, this method also holds challenges. Mold life is short, and larger runs of the
same items are usually required because the speed with which the molds are turned over
naturally produce more ware.
Advantages:
1. High productivity (Nearly double) compared to traditional bench casting methods.
2. Ease of mould handling as the mould need not be lifted and only need to be slided in
the rail.
3. Minimized the possibility of mould breakage and damages (chipping) that often
happens in bench casting.
4. Space required is very low compared to bench tradition casting.
5. More than one product from a mould is possible for small/Accessories products like
‘P’ or ‘S’ traps.
Limitation:
1. Producing complex patterns like one piece water closet are much difficult.

SUMMER INTERNSHIP
2. Switching from benching to Battery casting needs some design changes in mould.
The process flow chart of battery casting:
DRYING:
The point of drying is to simply remove water from the body without causing any damage.
Green pieces from casting will be sent to drier. In drier, Green M.O.R of the ware is
improved by removing the mechanically combined water from the ware. Moisture content of
green ware after drier will be approximately less than 1%.Drying process will take from 5-
6.5hrs depending upon various factors such as temperature, humidity, moisture content and
so on. The drier will be loaded at once and unloaded at once, this type of drier is called batch
drier. During this drying process the ware will lose its weight and also shrink in size. The
temperature is maintained carefully controlled (about 60-67). If the body has moisture in it,
when fired the moisture will turn into steam and expand, and if the steam cannot escape from
the piece fast enough, it will blow the piece up, thus it is essential to dry the ware before
firing.

SUMMER INTERNSHIP
Before sending to the ware drier, pieces are naturally dried for 2-3 days depending on
whether the climate is arid or humid.
Greenware that is of even thickness throughout is left to dry uncovered. Greenware that has
parts of varying thickness, especially small thin parts sticking out from larger masses is
wrapped loosely in polythene covers and allowed to dry slowly and evenly. If left to dry
uncovered, the thinner parts will dry and shrink faster than the thicker parts and may crack
where they join.
As the body is getting dried, the grains of material shrink together to fill the space occupied
by the water. It is this shrinkage that brings the danger of damage to the ware during drying.
If one side dries more than the other one, shrinkage of the former one will be more than that
of the latter and hence the piece will either warp or crack.
When hollow forms are built, holes are punched for allowing the steam to escape. Otherwise
a hollow piece, without a hole can become a grenade. The holes are made large enough, so
that when the clay naturally shrinks from moisture loss.
Air circulation:
High pressure fans mounted on the roof recirculate air from the dryer and discharge the re-
heated air vertically downwards into air distribution cones for horizontal discharge through
the product setting. This creates a highly turbulent and variable atmosphere in the dryer
meaning that all product surfaces are exposed to an intermittent flow of drying air stream.
Waste Heat from the kilns further reduces the energy costs.
At the end of the drying cycle, which is of 5-6 hrs, it is normal to incorporate a 'cooling
period' to reduce the temperature of the ware back to a 'handleable' condition
Fully automatic Switchgear and Control Panels are located at the dryers. Inside of the
chamber, is made to hold ware trolleys so that drying goods can be taken in and out quickly.
Warm air from a cooling kiln is introduced from one side and a fan provides a draught across
the chamber through the ware racks. A constant movement of air over the drying ware is as
important as heat. The air is not saturated with water by just passing through the chamber
once, so in order to economize, most of the air is recirculated by the fan. A centrifugal fan is
used for this. The centrifugal fan at the same time draws hot air from the kiln via a duct
system. Rapid circulation of air is more energy-efficient for drying than high temperature.

SUMMER INTERNSHIP
INSPECTION & GLAZING
In this section ware will be inspected for defects. Defected wares will be repaired or rejected
depending upon the defect. Thoroughly checked wares will be sent for glaze spraying.
INSPECTION
In inspection, it is important to ensure that each piece of sanitaryware has been correctly
manufactured. It is the job of the clay inspection team to examine each piece and to rectify
any minor faults that may be apparent. This is a most important section of the factory, as any
ware that may be sub-standard that slips through this department without rectification will
probably be a reject piece after firing. The dried ware which are unloaded from drier are
inspected in inspection booths. In inspection booth the ware is checked for the defects like
pin holes, crack, bad finishing, leveling, chipping e.t.c.
These defects are repaired by rubbing with sand paper and blade by placing them on pallets.
If the piece is not repairable, it is rejected. Wet sponge is applied to ware for checking cracks
and pin holes and also for removing dust and smoothening the ware. By applying sponge to
ware crawling can be avoided. After checking the ware, if it is good the inspector stamps the
inspection number.
GLAZE SPRAYING:
Glaze is reduced into a fine spray i.e. collection of moving droplets as a result of atomization
(the process of breaking up bulk liquids into droplets).Glaze received from the MILL
HOUSE department will be used for spraying and they are stored in tanks. Different colors
are sprayed on wares as per the production schedule. Spraying will be done by manual
method. The glaze is sprayed by using spray gun. In the spray gun the glaze and compressed
air are combined and sprayed through a nozzle of diameter 1.6 mm which facilitates the
dispersion of glaze into a spray.
-AIR (AIR SPRAY) ATOMIZATION:
In air spray atomization, fluid (glaze) emerging from a nozzle at low speed is surrounded by
a high speed stream of air. Friction between the liquid and air accelerates and disrupts the
fluid stream and causes atomization.
The energy source here is air pressure. The operator can regulate the flow rate of fluid
independently of the energy source. (The glaze tank’s pressure of capacity 235-250 liters is
approximately 3.5 kg/ cm^2 and that of atomization pressure is 6 kg/cm^2).

SUMMER INTERNSHIP
GLAZING FLOWCHART:
Green ware drier
De-dusting of trolleys
& Green wares
Green ware Inspection
The dried ware after inspection is put on carrousel. The carrousel is rotating through the
After inspection sent for greenware
spraying
After glaze dried
Carousel & Manual Spraying
Glazed ware sent to kiln for firing

SUMMER INTERNSHIP
glazing booth. On it, rotating stands are fitted and the wares are put on stand. The carrousel
moves with certain speed which is adjusted for different patterns. For smaller patterns the
carrousel moves fast and for bigger patterns, it move slowly. The rotating stands are used for
easy spraying of glaze on ware.
The ware put on rotating stand is sprayed in first booth for first coating and passed on to
second booth for second coating. So, for every piece two coatings are given. After glaze
spraying, scraping of the ware is done with the help of round blade. While spraying it is seen
that at corners lot of glaze is not deposited, excess glaze is removed by sponging smoothly.
On spraying the spray gun must not be too close, to avoid air packing under the surface of the
glaze. Then the Hindware logo is stamped to wares and are kept on trolley and send to kiln.
Each carrousel has 8 inspection booths and 4 glazing booths. There is also a washer & drier
for cleaning of the pallets. Care has to be taken to ensure that the ware is completely glazed
in all appropriate areas and that no rippling of the glaze during application is allowed. The
glaze itself consists of the following minerals: zircon, flespar, quartz, calcite, kaolin, zinc
oxide. It is most important at this stage that all glaze is thoroughly tested by the laboratory to
ensure it complies with the required specifications.
The glaze is lost during the spraying process in the form of overspray. Manual operatives are
deployed to scrape down this glaze (also from the sides of the spray booths) and sent for the
MILL HOUSE department for further processing. This glaze is referred to as RECLAIMED
GLAZE, which can be reused for spraying by mixing it with the fresh glaze in desired
proportions after proper processing.

SUMMER INTERNSHIP
KILN
Firing is the final and important process in the sanitaryware production. Conversion of low
strength product into high strength, durable and chemical resistant product is achieved during
firing. Sanitaryware firing temperature can go up to 1220°C, it varies accordingly depending
on the composition of raw materials used.
The firing process is the process where clay, which have been compacted, are heated to a
temperature where useful properties will be developed. It encompasses physical and chemical
changes in the ceramic body accompanied by a loss of porosity and a subsequent increase of
density. The compacted body becomes bonded together in a matrix by vitrification.
Vitrification is the process of progressive reduction and elimination of porosity with the
formation of glassy phase as a result of heat treatment. Glass formation typically starts at
1100°C and accelerates with further increase in temperature. Once the desired amount of
porosity is obtained, the cooling is started. During cooling, the glassy phase freezes and
becomes rigid to form a strong bond with the crystalline phase of the body.
During the vitrification process, the following physical changes takes place in the ceramic
body:
 Shrinkage due to loss of open pores
 Development of closed pores
 Development of glassy phase
Normally two types of kilns are used in sanitaryware manufacturing industry.
Tunnel Kiln:
Tunnel kiln is a continuous kiln that is made up of a straight tunnel with arched or flat top.
Shuttle kiln:
Shuttle kiln is a chamber kiln that is used in sanitaryware manufacturing industry.
Hindware uses gas-fired tunnel kilns. This kilns run 24 hours a day. It is an uneconomical
proposition to switch these kilns, off and on to suit the market requirements. The temperature
control throughout the kiln in pre-heating, firing and cooling is closely controlled.

SUMMER INTERNSHIP
The kilns are complemented by a fully automated kiln car handling system. The whole car
movement both in the kiln and out of the kiln is automatically controlled by micro-
processors, thus removing the arduous manual work. Pushers move the train of cars non-stop
at a predetermined rate. This method is ideal for high volume continuous production process.
Kiln furniture (cars) system which is used to support green ceramics during the firing
process, is light weight and very thermal shock resistant which translates into low fuel cost
and long life.
The materials used for kiln furniture are:
 Cordierite
 Mullite
 Silicon Carbide
 90-99% Alumina
 Zirconia
Cordierite is the least expensive type kiln furniture and is the most widely used. It is also
relatively light in weight and has no thermal expansion and therefore, excellent thermal
shock resistance. Cordierite plates with holes form the shelves in furniture.
Mullite is more expensive than Cordierite and can be used at high temperatures. It is heavier
but is very strong, and therefore, can be made with thinner cross section. It too has good
thermal shock resistance. In addition to these, ceramic fiber is also used.
Silicon Carbide (SiC) has very high tensile strength, thus used in shelving. The advantage of
this material as shelving is strength, high thermal shock resistance.
Alumina is a little more expensive than mullite, however it can be used at very high
temperature. Zirconia is also used where alumina cannot be used for chemical reasons.
Sprayed ware will be loaded in kiln car. At least 1/2‘’ spacing is given between all the
pieces because pieces will expand during the firing cycle before it contracts and shrinks.Dust
and other impurities are removed from ware by air blower. Sanitary ware kiln have three
zones, pre heating, firing and cooling zones. In pre heating zone mechanically and
chemically combined water has been removed from the ware. At firing zone all the raw

SUMMER INTERNSHIP
material are fused together and glaze are fused evenly. At cooling zone sudden cooling is
done to create glossy surface. Once product fired, it will be moved to sorting area.
Kiln is used for firing the glazed ware and to convert the weak ware into a strong article
having low porosity and also to form a glassy phase which flows into the pores between the
particles and solidifies on cooling.
The car pushing time of a car is about 11minutes. For every 11 minutes a car is pushed out of
kiln. The cycle time of the kiln is about 12-14 hrs depending on once fire or refire.
The kiln has four zones
1. Pre – heating zone
2. Heating zone
3. Rapid cooling zone
4. Cooling zone
1. Pre –heating zone:
The pre- heating zone is from about 212°c to 411°c .Physically combined water and
chemically combined water are taken off in pre – heating zone. In order to decrease
the rate of reactions, temperature is increased slowly. .
Thermocouples are placed on roof of the kiln to indicate the temperature in each
module.
On the first module contravec fan is placed to avoid the heat from going out through the kiln
entrance. On the 2nd module exhaust fan is placed for sucking the waste gases. On the 7th
module induced tempering air fan is placed to circulate the heat throughout the pre- heating
zone.
2. Heating zone:
Body vitrification and glaze maturing takes place in heating zone. The pore spaces are filled
with glassy bond by melting of the feldspar in the body. The clay is converted into mullite
and free silica.

SUMMER INTERNSHIP
3(Al2O3 2SiO2 2H2O) 3Al2O3 2SiO3 + 4SiO2
Burners are provided for firing the wares in firing zone, its temperature is about 12040
c to
12180
c.
3. Rapid cooling zone:
In rapid cooling zone, rapid cooling fan is placed for cooling the ware with pumping air. The
rapid cooling fan is placed for a sudden decrease in temperature. Fast cooling is done to
avoid crystallization of the glazes. At this stage, gradual freezing to melts, beginning of
recrystallization, consolidation of the glassy phase, etc., happen.
4. Cooling zone:
1. Slow cooling
2. Final cooling
The slow cooling fan is placed for cooling the ware by pumping air. Slow cooling is done to
avoid development of cooling stresses. Slow cooling is carried out to even out the body
temperature at different areas. Because quartz conversion will takes place after this stage.
The recuperation air fan is placed for utilization of the waste heat. This recuperation air fan
sucks the air from the kiln supplies to the driers through ducts. At the kiln exit, blowers are
placed for cooling the wares to the room temperature. This is final cooling zone.
The reactions during firing can be grouped into the following categories:
 Loss of physical water, in the drier.
 Oxidation: It is important to oxidize all the carbon and volatilize it out of the ceramic
otherwise it may form black coring also sulphides will oxidize.
 Decomposition: The dehydroxylation of clay sometimes called the loss of chemical
water occurs.
Some materials that undergo decomposition are
Hydrates decompose to give off water
Carbonates for carbon dioxide & sulphates for sulpur dioxide
Kaolin to meta-kaolin and meta-kaolin to mullite and silica with an increase in
volume.

SUMMER INTERNSHIP
 Quartz transformation:
Silica undergoes several polymorphous modifications on heating which are as follows
Below 573°C- alpha quartz
573-867°C- beta quartz
867-1470°C-tridymite
1470-1710°C-cristobalite
above 1710°C-liquid
Any cristobalite or tridymite will remain on cooling but the majority of the silica
grains never transform beyond beta quartz. When cooled below 600°C, beta quartz
transforms abruptly to alpha quartz with a sudden volume change. Slow cooling
between 600-500°C is often required to prevent cracking. The larger the piece and the
greater the silica content, the slower the cooling during the transformation. The
sudden change of alpha to beta quartz on heating at 573°C does not cause as much
strain in the green ceramic body as cooling.
Sanitary ware firing Defects:
Belching of colored ware – Firing happened at reduction atmosphere. Insufficient air
supply given to the kiln.
Black Core – Insufficient soaking temperature during firing. Organic rich raw
materials are used.
Less glossiness – Some of the reasons for less glossiness are insufficient firing,
devirtification of glaze.
Bloating of wares – this defects happens when the thickness of the body is high so the
evolved gas cant able to escape from the ware.
Dunting – Fast firing up to 700 ºC. Temperature uniformity varies at different area of
the wares.

SUMMER INTERNSHIP
LABORATORY
In the lab, the tests from raw materials to fired ware are as following :
1. Raw materials testing
2. Plaster testing
3. Particle size test
4. Flow test for glaze
5. Water absorption
6. Slip for testing
7. MOR
8. Auto clave test
9. Loss on Ignition
10. T.D.S test for sample clay material
1. Testing of raw material:
Residue test:
Daily the raw materials are brought from storage chambers and broke in to small pieces. Mix
the material properly and make four parts. Take the material from each part and weigh
200gms on weighing balance. The material is sieved at bottom of tap water on #200 mesh.
After sieving the residue is taken in to bowl and put in drier for dry. Now again weigh on
balance.
Acid test:
Take the raw material and weighed 100gms. After that take a bowl with some amount of
water. The weighed material is poured in water. After some time add HCL (hydro chloric
acid) in that material. If the material is good no reaction is takes place.
Moisture content test:
Take the raw material and weight 100gms on weighing balance. Now the weighed material is
put in drier for one hour at 110°C. After one hour again it is weighed and the reading is
noted.
Moisture content (%) = Initial – Final *100
Initial

SUMMER INTERNSHIP
2. Plaster testing:
Take 525 ml of water in one beaker. Take another beaker and weigh 700gms of plaster of
Paris on beaker. Pour the plaster of Paris in 525ml beaker. Add the powder for 2 minutes and
2minutes soaking and 2 minutes mixing.
This process is 100: 75 ratios. After mixing pour the plaster in bars. Before pouring apply the
soap solution for bars and moulds and Put that up to setting. Soap solution is used for easily
removing. After setting remove the bar moulds.
The plaster is poured in brass ring. After pouring lift the brass ring suddenly. The plaster is
spread roundly to certain area. The spread area is calculated is spread value.Take one
cylindrical mould and pour the remaining plaster in it. After setting the bars and this
cylindrical piece are put in drier for four days. After four days the cylindrical piece is
weighed and put in water absorption. The bars are put in M.O.R (Modules Of Rupture)
machine and check the MOR.
3. Particle size test (Manual):
Take the glaze and pour above half of the density bottle and add water. After that weigh the
density bottle. The reading is noted. After that take 1000 ml of cylindrical beaker and add 2%
of sodium hexa Meta phosphate solution. Now pour the glaze in cylindrical beaker and add
the ice pieces in beaker and pour cold water up to 1000ml mark. Now stirring the solution for
one minute. Then UN disturb for 17minutes. After 17min put hydro meter in beaker. It shows
the reading up to which reading it dips. Note the reading and remove the hydro meter.
PARTICLE SIZE DETERMINATION (PSD):
Malvern Master Size Micro:
The instrument used for PSD is Malvern Master Size Micro-UUK Product. We can measure
the size of the particle from 0.3 to 300 Microns.
Measurement Principle:
Based on the laser diffraction method the master size analysis particle size of the Raw
materials.
Laser Diffraction:
Laser diffraction particle size analysis is based on the phenomenon that all particles scatter
light at a range of angles, which is a characteristic of their size large particles scatter at small
angles and vice versa.
The master size micro comprises a Helium-Neon laser as a light source, which illuminates
the dispersed particles in the measuring zone. this is then focused by a Fourier lens to a

SUMMER INTERNSHIP
detector. Which consists of a large number of photosensitive elements radiating out ward
from the centre. a never property of a Fourier lens is that it collets the scattered light from an
ensemble of particles, and over lays the common angles of scattering on the detector array
the intensity of the scattered light is measure and using an optical model(Mietheory) of
calculate the scattering patern and a mathematical deconvolution procedure, a volumetric
particle size distribution is calculated that best mathes the measured patern.
The master size micro produces volume –based measurements of ensemble of particle
sampled at a rate of 500snaps per second. Simultaneously from all detectors. This means that
the system is exceptionally suitable for the detection of rogue coarse particles.
4. Flow test for Glaze:
Take the glaze and pour in the mould. After some time it dry, the glaze remove from the
mould by using hack saw blade. After removing put in drier for 2 hours, after 2 hours remove
from drier.
Take one small cylindrical mould for getting the glaze cylindrical shape. It is occurred by
tapping the bolt in the mould. Now the cylindrical shape of glaze piece is weighed 200gms.
The extra material is removed by rubbing on sand paper. The 200gms glaze piece is put in
flow mould by add C.M.C to mould because to stick the glaze piece to mould. After that send
for firing in kiln. After completion of firing, the glaze is flow to some distance in flow meter.
The distance is calculated by using vernier calliperse.
5. Water absorption:
Take one pattern ware and break the ware. Take three pieces from top, middle and bottom by
using hammer. Mark for each piece by pencil for determining. Then see the thickness for
each piece and note the reading. After that put in drier for 1 to 2 hours. After drying remove
the pieces from drier and put for cooling. Then see the weights in weighing balance. Then put
the pieces in vaccume chamber for one hour. After that put in water heater machine for half
an hour. Switch off the heater and kept for total night. Morning weigh the pieces and note
the reading. This is saturated weight. The % of water absorption is calculated by using
formula.
Saturated wt – fired wt x 100
W/A = fired weight
The result is noted.
6. Slip testing:
The below tests are for slip. They are
1. Litre weight

SUMMER INTERNSHIP
2. Fludity&Thixotropy
3. Casting rate
4. Residue
5. Shrinkage
6. Deformation
7. M.O.R
Casting rate:
First we take slip from one point of casting. This casting slip is poured in bowl mould and
kept for one hour. After one hour, unload the slip and keep it for half an hour for drying.
After half an hour cut a piece and check the casting rate by using vernier calipers.
Fluidity & thixo:
Fluidity and thixo is checked by using torsion visco meter. First we set the visco meter at
zero. Take a beaker and pour the slip in that and stirring for one minute. After
stirring put the beaker just below the visco meter and release it. The pointer shows the
reading. Put the beaker for one minute without disturbing. Again put the beaker below the
visco meter and release, the pointer shows reading. This reading is thixo.
Half litre weight:
Take 500ml. beaker and pour the slip in that beaker. Before pouring the slip weigh the empty
beaker. After pouring again weigh the beaker. Note the reading.
After testing the slip of supply tank it can be supplied to casting points
Residue:
Take 500ml of slip and pour in to 200# mesh. The slip is sieved by adding water in 200
mesh. After sieving some material is remaining on the sieve. The remaining material is put in
drier for one hour at the temperature of 1100
c. After one hour remove the material from drier
and weigh using weighing balance.
Shrinkage:
Take the bar moulds and cleaned properly after that pours the slip in the mould. Put the
mould up to slip setting. Then release the moulds and remove the bar pieces. Now take the
vernier and mark at zero and 100mm. After marking put in drier for 2 hours at the
temperature of 110c. After drying see the shrinkage by using vernier (L1). After that put for
firing and again see the fired shrinkage (L2).
Shrinkage = (L1 – L2) /L1 x 100

SUMMER INTERNSHIP
Deformation:
Take the slip and pour in bar moulds. After setting release the moulds, and remove the
articles and give finishing. After that put in drier for 2 to 3 hours at the temperature of 110c.
After drying remove the bars and put in stand are send to firing after completion of firing, to
see the deformation.
7. M.O.R
M.O.R means modules of rupture. Take the fired bars and put on the stands of M.O.R
machine. The M.O.R machine consists of dial gauge which shows the reading. While starts
the machine, the shaft slowly pushes up the bar and the pressure is showing by dial gauge.
When the bar break at which pressure is showing by dial gauge is the reading of the M.O.R.
8. Auto clave test:
Take five types of selected wares and break the wares. Bring five pieces from that wares and
place on auto clave in metal frame. The water level is above of the wares on metal frame.
Close the auto clave and tighten the bolts of lids strongly. For not leakaging of steam on
heating. Heat the auto clave by using gas cylinder. The heat is given from bottom of the auto
clave. The pressure is increasing slowly and the reading is shown in dial gauge. The pressure
is 3.5 to 4.0 kg/cm2. This pressure is maintaining for 10 hours. After 10 hours cool the auto
clave by releasing steam. Open the lid and remove the wares. Apply blue dye for the wares
for easy determining of fine hair line cracks. Wash the wares after applying of dye. Then see
the cracks on wares.
9. Loss on ignition:
Take the dry piece which is fully dried one and weight the piece on weighing balance is (w1).
After that sent to firing on kiln. After firing again weight the piece on weighing balance is
(w2). Apply the formula of % of L.O.I. The result of L.O.I % is noted
% of L.O.I = W1 - W2 / W1 x 100 .
10. T.D.S test for sample clay material:
Take 1000ml measuring cylinder and RO water. Take 465 gms for sample clay material and
crusher in fine powder. Take 930ml of water in measuring cylinder add 465gms of sample
clay material to the water in the measuring cylinder. Close the top of the measuring cylinder
and invert or till it for 6 times and soaked the material over night for 12hrs.
Soluble salts in clay material get dissolved in the water. And the material settle down at the
bottom and water will be at the top using meter. check the TDS of the clay material.

SUMMER INTERNSHIP
In brief the laboratory test are:
1. Clay test (Plastic materials)
1. Moisture content in clay
2. Alkali demand test
3. Residue test
4. Shrinkage test
5. Loss of ignition test(LOI)
6. Water absorption
7. Casting rate
8. MOR
9. Iron test
2. Quartz /Feldspar test (Non-plastic materials)
1. Residue test
2. Iron test
3. Moisture test
4. Cone test
3. Glaze test
1. Fired glaze color test
2. Residue test
3. Iron test
4. Slip test
1. Density/Specific Gravity
2. Flow
3. Thixotropy
4. Residue test
5. Shrinkage test
6. Warpage

SUMMER INTERNSHIP
7. MOR
8. Permeability test
5. Glaze test
1. Density/Specific Gravity
2. Viscosity
3. Drying time
4. Flow test
5. Color matching
6. Residue test
7. PSD test
6. Plaster of Paris test
1. Residue test
2. Initial and final setting time
3. MOR
4. Absorption percentage
7. Fired ware test
1. Water absorption test
2. Crazing test
3. Thermal shock resistance
4. Chemical resistance test

SUMMER INTERNSHIP
FEW DEFECTS
1. Cracks –One of the major defect found in the Sanitaryware production process.
Separation/Split of Sanitaryware surface without breaking apart.
2. Blisters – Blistering is sharp-edged burst bubble. Can be found in fired ware.
3. Crazing – Crack in glaze surface area.
4. Pinhole – Small holes in the ware.
5. Poor finish – Improperly finished ware at green stage which is found after firing.
6. Improper/Defective logo – Logo is not properly printed or positioned.
7. Iron specks –Iron speck found in Glaze surface. Defect can be found after firing.
8. Stuck – two or more wares stuck together during firing of ware.
9. Chipping – Small Broken piece from the ware.
10. Light glaze – less glaze in ware than necessary.
11. Heavy glaze – More glaze in ware than necessary.
12. Wavy glaze – Wavy ness of glaze due to improper glaze application.
13. Crawling – Small portion of the glaze separates from ware leaving the ware
exposed.
14. Leakage – Leak found in ware during water filled and flushed.
15. Poor repair – Defect due to poor repairing at various stages at process.
16. Pitting – Small pits in glaze found after firing.
17. Under fired – Improperly fired
18. Warpage – Bending in ware.
19. Sulphuring – Dull scum on glaze surface found after firing.
20. Color fading – Color disappearing after firing.
21. Bloating – Gas bubble trapped in body during firing.
22. Blown out – Impurities burns out during firing.
23. Dunting – Crack formed at silica inversion stage and the glaze filled the crack.
24. Peeling – Gaze lift away from body.

SUMMER INTERNSHIP
Sorting
In this stage of the process all wares from the kiln are inspected and sorted according to the
Defects. If ware is defects free then it will be send to packing section for packing. If ware has
minor defects like pin holes then it will be repaired by cold fill. If has light glaze or wavy or
blib then it will be sent to refire section.If there is a crack it will be rejected. This quality
check is very important to maintain standards. And also random sampling will be made for
flush test, smoke test, leak test and load test.
Refire/Rework
All repair wares will be send to rework section for minor repairs. All ware are required
according to the defect and sent to tunnel kiln. Once repaired and fired again it will be
inspected and again separated as per the grade. If quality standards are met then it will sent to
packing. If needs repairing again it will repaired in refire section. Major and un-repairable
wares will be sent to rejected area.These are normally warpage or cracked pieces.
Packing
It is the final stage of sanitary ware manufacturing/production process. All Sanitary wares
that are passed quality standards are packed and dispatched to ware house.

HSIL CD-II (1)

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Similar to HSIL CD-II (1)

Similar to HSIL CD-II (1) (20)

HSIL CD-II (1)