1. Page 1
Khaled Mohammed Abd El-Aziz
Electrical Power Engineer
Mobile: 01272279767 / 01007326134 / 01114093120
Phone: 0233883733
Email: engineer_khaledmohamed@hotmail.com
Personal Information
Nationality: Egyptian.
Birth Date: February, 11 1990.
Address: 19 Sahel 7amza, El Haram, Giza
Military Status: Finished the service
Language skills:
- English: Very Good
Education
Sept. 2007 – May 2012 B. Sc. of Power and Electrical Machines Engineering,
Faculty of Engineering, Helwan University
Accumulative Grade: Good (71%).
Fourth Year Grade: Very Good
Project Grade: Excellent
Graduation Project Design of Electrical Power Distribution System for
An Industrial City.
Work Experience
Electrical Maintenance Engineer
BAPETCO (Bader El Din Petroleum Company)
(1/1/2016-Now)
At OBAIYED Field (Egyptian Western Desert Oil & Gas Plant)
Work Activities
1- Responsible for modifying and applying the preventive and corrective
maintenance programs including train and total shutdowns, workshop tools,
equipment spare parts ordering, and choosing, quality control, stock materials
preparation and chasing, material stock level adjustment and all synchronous
2. Page 2
& induction machines overhauling, condition monitoring, troubleshooting, and
cause failure analysis.
2- Provide technical support to the maintenance department in respect of
problem identification/solving and assisting in operational improvements
related to plant/equipment reliability and integrity.
3- Perform job hazard analysis, and task risk assessments for electrical related
works.
4- Responsible for issuing Permits to Work, daily reports, hand overs, major
overhauls reports & failure reports.
5- Experience in determines the material required & the spare parts for elec.
Equipment, material stock levels adjustment, review and revise of material
quotations and inspection of materials after arrived to warehouse.
6- Have full knowledge in the use/application of workshop equipment/tools, and
be able to offer innovative solutions for equipment repair.
7- Establish equipments, monitoring parameters, preparation of job procedures
and switching procedures, executing alterations and modifications.
8- Compiling Operating & Maintenance Manuals for associated jobs and
shutdowns.
9- Investigate/trouble shoots all equipment failures and initiates necessary
action.
10-Operate & Maintenance for Hydraulic & Corrosion Panels at gas wells.
11-Operate & Maintenance for Low Voltage switch gears 400 V.
12- Operate & Maintenance For PMS Brush Type.
13-Calibrate & Test the Protection Relays type CEE for 11kV Switch Gears.
14-Operate & Maintenance 11 kV Electric motors.
15- Operate & Maintenance 11/0.4 kV Power transformers.
16-Operate & Maintenance medium voltage 11 kV Switch gears Siemens.
3. Page 3
AUTOMATION ENGINEER at [UNITED ENGINEERS SYSTEM INTEGRATOR
BY SIEMENS]
(1/1/2014-1/1/2016)
Working at (PLC & Scada: S7200-S7300-S7400-S71200-WINCC-WINCC
FLEXIBLE-TIA)
Working at (Drives: Siemens MicroMaster-Sinamics)
Projects
AGIBA Petroleum Company
(Zarif Process Upgrading Project)
Development of conventional control to S7-300 Redundancy System.
Design Power and control panels For the New PLC system.
Programming of PLC by Using Step7 Simatic Manger Software.
Design The System using HMI and PC as Engineering station By WINCC
Flexible.
Upgrading the Pneumatic Systems TO I/P Systems, Upgrading To PID Control
for Valves.
Communicate With Murphy Controllers OF Shipping Pumps Through Modbus
Serial Communication To The PLC & SCADA System.
Communicate OF PLC & SCADA on AGIBA WAN Through Ethernet
Communication.
Amal Petroleum Company
(9 Wells Upgrading Project- OffShore)
Upgrade 9 Wells Control to PLC S7-300
Programming of PLC by Using Step7 Simatic Manger Software.
Communicate With Invensys DCS through Modbus Communication, S7-300 as
Modbus Slave
EZZ Steel Water Treatment station
(Blow Down Water Treatment Plant BWTP)
Design PLC control panels S7-300-SWR for the System.
Programming For PLC using Step7 Simatic Manger Software.
Programming SCADA using Wincc Advanced v13 TIA.
Communicate With 4 S7-1200 Ro Skids To The Scada Through Ethernet
Communication.
Two Operation For All Motors:
Automatic from PLC
Manual from MCC
Alfa Feed Factory
Design PLC control panel S7-300 for the Factory.
Programming For PLC using Step7 Simatic Manger Software & For the Scada
Using Wincc Flexible.
4. Page 4
Fine Water Treatment station
Design Scada for the Water Treatment Station by using WINCC Flexible.
Glaxo for Medicine Company
(ATS Machine)
Development of conventional control and interlock system to S7-PLC System
Design Power and control panels For the New plc system and programming the
machine by using HMI with TIA Software.
Glaxo for Medicine Company
(Siebler Machine)
Upgrade for S5 plc system to S7-300 plc system
Design and programming the machine by using HMI With WINCC Flexible.
ALTUBE; Arabian Oil & Gas pipe lines co.)
1. Project Details for SCADA System:
1. The project is a station to store and distribute the petroleum products to the
consumer and transmitting them to another station, the station stores four
different products and its feeding is from two lines.
2. We made an automatic and manual control system by using two operator
stations as a SCADA system, the programming of the project has been done by
using 4H system, the programming of the screens has been done by using
WINCC software, the whole system is a redundant system including the
hardware and the software.
2. Degwe Project at ALTUBE:
Power and control panel for Water Treatment Plant and Sewage Station,
controlling by using PLC S7-1200 and Communicate with SCADA system.
Design Power Panels
Design Power Panels for Khalda, Petrobel, Gupco.
OFFICE Technical Engineer
Also worked as office Technical engineer, I have many responsibilities like
Making Site survey, studying all tenders and prepare suitable Technical &
Commercial offers.
5. Page 5
Internship Experience
Aug. 06 2011-Aug. 18 2011 South of Cairo for Electrical
Distribution Company
Deal with Cables, Transformers, Protection circuit
Power factor correction, Circuit Breakers, Distributors
Aug. 22 2011-Sep. 8 2011 El Nasr Company For
Coke & Chemicals
Design and implementation control & Power circuits
Manual and Automatic for conveyor and for engines
Medium and low pressure
Design and implementation of control & Power circuits
In Plc in ladder program
Training Courses
Automatic control (Classic Control)
– Different Control & Power circuits for 3 phase motors
PLC Course ( Siemens Training Lab )
- Introduction to plc S7-300 Series
- Simatic Manger & Hardware Configuration
- Blocks & Programming language & Symbol Table
- Timers & Counters & Comparators
- Make Practical Application on [S7-313C (2DP)}
Design For Electric Distribution for projects
- AutoCAD (2D)
- Lighting Design & Sockets Design & Circuit Breaker Selection
- Cables & Bus Bar & Distribution Board Design
- Transformer & UPS & Air Condition (HVAC)
- Feeding System & Power Factor Correction
- Short Circuit & Voltage Drop Calculation
Protection Course
- Contents of Switch gear substation
- Types of Circuit Breakers (Air CB, Oil CB, SF6 CB and Vaccum CB)
- Protection system techniques
