Caterpillar Cat 980H Wheel Loader (Prefix JMS) Service Repair Manual (JMS00001 and up).pdf

Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980H WHEEL LOADER JMS
Configuration: 980H Wheel Loader JMS00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
980H Wheel Loader Power Train
Media Number -RENR8667-08 Publication Date -01/09/2018 Date Updated -04/09/2018
i04400940
Torque Converter - Assemble - Heavy duty
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B
8T-5096 Dial Indicator Test Group 1
5P-2390 Gauge Tool Group 1
C 1P-0520 Driver Group 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Note: Apply oil to all of the bearings before assembly.
1/18
980H Wheel Loader JMS00001-UP (MACHINE) POWERED BY C15 Engine(SEBP4...
2021/3/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g00504278
1. Use Tooling (C) to install sleeve bearing (59) in cover assembly (57). Sleeve bearing (59)
must be even with the outside surface of cover assembly (57).
2. Install cover assembly (57) to rotating housing (39).
3. Install ring seal (58) to rotating housing (39).
2/18
2021/3/25

4. Install eight bolts (56) and the washers. Tighten the bolts to a torque of 30 ± 5 N·m
(22 ± 4 lb ft).
5. Install thrust bearing race (54), thrust bearing (55), and thrust bearing race (54) to cover
assembly (57).
6. Install retaining ring (53) in turbine hub (51).
3/18
2021/3/25

7. Install converter turbine (50) on turbine hub (51).
8. Install twenty bolts (52). Tighten the bolts to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
9. Install turbine hub (51) and converter turbine (50) as a unit to rotating housing (39).
10. Install two thrust bearing races (49) and the bearing to the hub.
4/18
2021/3/25

11. Use Tooling (C) to install sleeve bearing (48) to carrier assembly (44). Bearing sleeve (48)
must be even with the counterbore of carrier assembly (44).
12. Install retainer ring (47) in stator (46).
13. Position carrier assembly (44) on a wood block.
5/18
2021/3/25

14. Use proper equipment to handle stator (46). Heat stator (46) to a maximum temperature of
121°C (250°F) for one hour.
15. Install stator (46) on carrier assembly (44).
16. Install snap ring (45) in stator (46).
17. Install stator (46) and carrier assembly (44) in rotating housing (39).
6/18
2021/3/25

18. Install two thrust bearing races (43) and the thrust bearing to the carrier assembly.
19. Position impeller hub (42) on a wood block.
20. Install converter impeller (41) on impeller hub (42).
21. Install drive flange (38) on converter impeller (41).
7/18
2021/3/25

22. Install twelve bolts (40). Tighten the bolts to a torque of 80 ± 10 N·m (60 ± 7 lb ft).
23. Install drive flange (38) on rotating housing (39). The weight of drive flange (38) is 23 kg
(51 lb).
24. Install 36 bolts (37) and the washers. Tighten the bolts to a torque of 30 ± 5 N·m
(22 ± 4 lb ft).
25. Install retaining ring (36) in the groove of drive gear (35).
8/18
2021/3/25

26. Use the proper equipment to handle outer bearing race (60). Lower the temperature of outer
bearing race (60).
27. Install outer bearing race (60) in drive gear (35). Make sure that outer bearing race (60)
makes contact with retaining ring (36).
28. Install drive gear (35) on drive flange (38).
29. Install twelve bolts (34) and the washers. Tighten the bolts to a torque of 50 ± 7 N·m
(37 ± 5 lb ft).
9/18
2021/3/25

30. Use the proper equipment to handle inner bearing (33). Heat inner bearing (33) to a
maximum temperature of 135°C (275°F). Install inner bearing (33) on bearing carrier (28).
31. Install retaining ring (32) in the groove of bearing carrier (28).
32. Use the proper equipment to handle ring carrier (31). Heat ring carrier (31) to a maximum
temperature of 135°C (275°F). Install ring carrier (31) on bearing carrier (28).
10/18
980H Wheel Loader JMS00001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/25

33. Install seal ring (30) on ring carrier (31).
34. Install O-ring seal (29) on bearing carrier (28).
35. Install bearing carrier (28) in drive flange (38).
36. Install retaining ring (27) in carrier assembly (44) in order to hold bearing carrier (28) in
place.
11/18
2021/3/25

37. Install two studs (26) in torque converter housing assembly (2). Tighten the studs to a torque
of 100 ± 15 N·m (74 ± 11 lb ft).
38. Install retaining ring (24) in the groove of idler gear (15).
39. Use the proper equipment to handle bearing cup (25). Lower the temperature of bearing cup
(25). Install bearing cup (25) in idler gear (15).
12/18
2021/3/25

40. Flip idler gear (15) to the opposite side. Install bearing cup spacer (23) in idler gear (15).
The notch in bearing cup spacer (23) must be aligned with retaining ring (24).
(22). Install bearing cup (22) in idler gear (15).
42. Install bearing cone (21), bearing cone spacer (20) and bearing cone (19) in idler gear (15).
13/18
2021/3/25

43. Apply clean hydraulic oil on O-ring seal (17). Install O-ring seal (17) on shaft assembly
(18).
44. Install 1/2" - 13 NC guide pin (61) in shaft assembly (18).
45. Hold transfer gear (15) in position in torque converter housing assembly (2). Install shaft
assembly (18).
46. Remove guide pin (61) from shaft assembly (18).
14/18
2021/3/25

47. Install bolt (14) that holds shaft assembly (18) in place in torque converter housing
assembly (2). Tighten the bolt to a torque of 120 ± 20 N·m (90 ± 15 lb ft).
48. Use the proper equipment to handle bearing cones (12). Heat bearing cones to a maximum
temperature of 135°C (275°F). Install a bearing cone (12) on each side of pump drive gear
(11).
(13). Install bearing cup (13) in torque converter housing assembly (2).
15/18
2021/3/25

50. Install pump drive gear (11) in torque converter housing assembly (2).
(8). Install bearing cup (8) in pump adapter (6).
52. Install shims (9) on pump adapter (6).
53. Apply clean hydraulic oil on O-ring seal (10). Install O-ring seal (10) on pump adapter (6).
16/18
2021/3/25

54. Install two 3/8" - 16 NC guide pins (62) in torque converter housing assembly (2).
55. Install pump adapter (6) on torque converter housing assembly (2).
56. Install thirteen bolts (5) and the washers.
57. Use Tooling (B) to check bearing end play. The bearing end play must be 0.15 ± 0.05 mm
(.006 ± .002 inch). Add or remove shims in order to get the correct bearing end play.
Note: If end play is less than 0.10 mm (.004 inch) add additional shims. If end play is
greater than 0.20 mm (.008 inch) remove shims.
58. Apply clean hydraulic oil on O-ring seal (4). Install O-ring seal (4) on torque converter
housing assembly (2).
17/18
2021/3/25

59. Install two 1/2" - 13 NC guide pins (63) in the carrier assembly.
60. Install Tooling (A) to torque converter housing assembly (2), as shown. Attach a hoist and
suitable lifting chains to Tooling (A). Use the hoist to carefully install torque converter
housing assembly (2) on the torque converter.
61. Install eight bolts (1) and the washers to torque converter housing assembly (2). Tighten the
bolts to a torque of 120 ± 20 N·m (90 ± 15 lb ft).
End By:
a. Connect the torque converter to the transmission and to the output transfer gears. Refer to
Disassembly and Assembly, "Torque Converter to Transmission, Output Transfer Gears -
Connect" for the machine that is being serviced.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Mar 25 15:57:33 UTC+0800 2021
18/18
2021/3/25

Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980H WHEEL LOADER JMS
Configuration: 980H Wheel Loader JMS00001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
980H Wheel Loader Power Train
Media Number -RENR8667-08 Publication Date -01/09/2018 Date Updated -04/09/2018
i05903287
Torque Converter (Freewheel Stator) - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B
8B-7548 Push-Puller 1
8B-7550 Leg 2
8H-0684 Ratchet Wrench 1
8B-7560 Step Plate 1
8H-0663 Bearing Puller Attachment 1
C
8B-7548 Push-Puller 1
8H-0684 Ratchet Wrench 1
8B-7549 Leg 2
5P-4808 Cap 2
8B-7554 Bearing Cup Puller Attachment 1
D
5F-7343 Bearing Puller Attachment 1
1P-0520 Driver Group 1
E 1P-0510 Driver Group 1
F 7
1/19
2021/3/25

Forcing Screw
3/8 - 16 x 3 in
Start By:
A. Separate the torque converter from the transmission and from the output transfer gears.
Refer to Disassembly and Assembly, "Torque Converter from Transmission, Output
Transfer Gears - Separate" for the machine that is being serviced.
1. Place the torque converter housing assembly (2) on wood blocks.
2. Remove bolts (1) and the washers from torque converter housing assembly (2) .
3. Install Tooling (A) to torque converter housing assembly (2) , as shown. Attach a suitable
lifting device to Tooling (A) . The weight of housing assembly (2) is approximately 120 kg
(265 lb).
4. Use Tooling (F) to loosen housing assembly (2) from the torque converter.
2/19
2021/3/25

5. Remove housing assembly (2) from the torque converter.
6. Remove O-ring seal (3) from torque converter housing assembly (2) .
7. Remove bolts (4) and the washers from pump adapter (5) and torque converter housing
assembly (2) .
3/19
2021/3/25

8. Use Tooling (F) to remove pump adapter (5) from torque converter housing assembly (2) .
9. Use tooling (C) to remove bearing cup (6) , O-ring seal (8) , and shims (7) from pump
adapter (5) . See illustration 13 for Tooling (C) .
4/19
2021/3/25

10. Remove pump drive gear (9) from torque converter housing assembly (2) .
11. Use Tooling (B) to remove bearing cones (10) from each side to pump drive gear (9) .
12. Use Tooling (C) to remove bearing cup (11) from torque converter housing assembly (2) .
See illustration 13 for Tooling (C) .
5/19
2021/3/25

13. Remove bolt (12) and the washer from torque converter housing assembly (2) .
14. Use Tooling (F) to push shaft assembly (14) out of torque converter housing assembly (2) .
15. Remove idler gear (13) from torque converter housing assembly (2) .
16. Remove O-ring seal (15) from shaft assembly (14) .
6/19
2021/3/25

17. Remove bearing cone (16) , bearing cone spacer (17) , and bearing cone (18) from idler gear
(13) .
18. Use Tooling (C) to remove bearing cup (19) from idler gear (13) .
19. Remove bearing cup spacer (20) from idler gear (13) .
7/19
2021/3/25

20. Remove retaining ring (21) from idler gear (13) .
21. Use Tooling (C) to remove bearing cups (22) from idler gear (13) .
8/19
2021/3/25

22. Remove studs (23) from torque converter housing assembly (2) .
23. Remove retaining ring (24) and bearing carrier (25) from the carrier assembly.
24. Remove bearing carrier (25) .
9/19
2021/3/25

25. Remove O-ring seal (26) from bearing carrier (25) .
26. Remove seal ring (27) from ring carrier (28) .
27. Use Tooling (D) and a press to remove ring carrier (28) from bearing carrier (25) .
10/19
2021/3/25

28. Remove retaining ring (29) from bearing carrier (25) .
29. Use Tooling (D) and a press to remove inner bearing (30) from bearing carrier (25) .
30. Remove bolts (31) and the washers from drive gear (32) .
31. Remove drive gear (32) .
11/19
2021/3/25

32. Use Tooling (E) and a press to remove the outer bearing race (32A) (not shown) from drive
gear (32) .
33. Remove retaining ring (33) from drive gear (32) .
12/19
2021/3/25

34. Remove bolts (34) and the washers from drive flange (35) and rotating housing (36) .
35. Use bolts (34) as forcing screws to remove drive flange (35) from rotating housing (36) .
The weight of drive flange (35) is 23 kg (51 lb).
36. Remove bolts (37) from drive flange (35) .
13/19
2021/3/25

Please write to us.
Our email:
aservicemanualpdf@yahoo.com
Please go to the homepage
to get the full manual, or
other brand PDF manuals.
Home Site:
aservicemanualpdf.com

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/

37. Remove drive flange (35) from impeller (38) .
38. Position impeller hub (39) on wood blocks.
39. Remove impeller (38) from impeller hub (39) .
14/19
2021/3/25

40. Remove thrust bearing (40) and race (40A) (not shown) from carrier assembly (41) .
41. Remove carrier assembly (41) and stator (42) as a unit from rotating housing (36) .
42. Remove snap ring (43) from stator (42) . Remove plate (44) from stator (42) .
15/19
2021/3/25

43. Remove 11 freewheel rollers (45) and 11 freewheel springs (46) from freewheel cam (47) .
Remove stator (42) from carrier assembly (41) .
44. Remove retaining ring (48) . Remove plate (49) .
45. Use Tooling (E) and a hydraulic press in order to remove freewheel cam (47) from stator
(42) .
Note: If necessary, heat the stator to a maximum temperature of 135 °C (275 °F) for
approximately 15 minutes.
46. Remove thrust bearing (50) from carrier assembly (41) . Remove sleeve bearing (51) from
carrier assembly (41) .
16/19
2021/3/25

Caterpillar Cat 980H Wheel Loader (Prefix JMS) Service Repair Manual (JMS00001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 980H Wheel Loader (Prefix JMS) Service Repair Manual (JMS00001 and up).pdf

Similar to Caterpillar Cat 980H Wheel Loader (Prefix JMS) Service Repair Manual (JMS00001 and up).pdf (20)

More from fjkskkedmm4r

More from fjkskkedmm4r (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 980H Wheel Loader (Prefix JMS) Service Repair Manual (JMS00001 and up).pdf