This document provides assembly instructions for a torque converter in 3 sentences or less:
The document outlines over 60 steps to assemble a torque converter for a 980H wheel loader, including installing various bearings, seals, gears, housings, and fasteners in the proper sequence and with specified torques. Precautions are provided to handle parts carefully and apply lubricants as needed during assembly. Tools required for the assembly process are also listed.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides disassembly instructions for a torque converter in 3 steps:
1. Remove the torque converter housing from the transmission.
2. Disassemble the internal components of the torque converter housing.
3. Clean all torque converter parts thoroughly before inspection and assembly.
This document provides disassembly instructions for a torque converter in 3 steps:
1. Remove the torque converter housing from the transmission.
2. Disassemble the internal components of the torque converter housing.
3. Clean all torque converter parts thoroughly before inspection and assembly.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, races, and gears in the specified order while following torque specifications.
2. Install the stator, carrier assembly, impeller, and drive flange. Fit the idler gear, shaft assembly, and pump drive gear into the torque converter housing.
3. Attach the pump adapter and check bearing end play using gauges before applying the final seal.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides disassembly instructions for a torque converter in 3 steps:
1. Remove the torque converter housing from the transmission.
2. Disassemble the internal components of the torque converter housing.
3. Clean all torque converter parts thoroughly before inspection and assembly.
This document provides disassembly instructions for a torque converter in 3 steps:
1. Remove the torque converter housing from the transmission.
2. Disassemble the internal components of the torque converter housing.
3. Clean all torque converter parts thoroughly before inspection and assembly.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, races, and gears in the specified order while following torque specifications.
2. Install the stator, carrier assembly, impeller, and drive flange. Fit the idler gear, shaft assembly, and pump drive gear into the torque converter housing.
3. Attach the pump adapter and check bearing end play using gauges before applying the final seal.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps to assemble the torque converter components and attach it to the transmission housing. It then describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, disconnecting electrical and hydraulic lines, and lifting components with the specified tools. The purpose is to connect or separate the torque converter, transmission, and output transfer gears on a 980M wheel loader.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Proper tools and torque specifications are listed. Finally, it states to connect the assembled torque converter to the transmission and output transfer gears.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important, as is applying clean hydraulic oil and torquing bolts to specified values.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps to assemble the torque converter components and attach it to the transmission housing. It then describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, disconnecting electrical and hydraulic lines, and lifting components with the specified tools. The purpose is to connect or separate the torque converter, transmission, and output transfer gears on a 980M wheel loader.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important, as is applying clean hydraulic oil and torquing bolts to specified values.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps for installing various components like seals, bearings, gears, and housing pieces. It also describes using specialty tools and proper torque specifications. Separately, it outlines 5 steps for removing a transmission from output transfer gears, which involves lifting components, disconnecting lines, and removing bolts.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important during assembly. Finally, the manual specifies torques for fasteners and checking bearing end play.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important during assembly. Finally, the manual specifies torques for fasteners and checking bearing end play.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps for installing various components like seals, bearings, gears, and housing pieces. It also describes using specialty tools and proper torque specifications. Finally, it explains how to separate the transmission from the output transfer gears by removing bolts, disconnecting lines, and lifting components with brackets.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install internal components like thrust bearings and seals in sequential order into the housing.
2. Heat critical components like bearings to specific temperatures and install carefully. Attach the drive components including impeller, turbine, and stator.
3. Secure the housing cover and install external mounting brackets and hardware. Check clearances and lubricate seals before final assembly.
This document provides assembly instructions for connecting a torque converter to a transmission and output transfer gears on a 980G wheel loader. The procedure involves 62 steps, including installing various components like an output shaft, O-rings, and link brackets. Tools required include a stand, link brackets, and dial indicators. Cleanliness is important during assembly and all parts must be inspected for wear before installation.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and tools are used to safely handle components weighing up to 1406 kg.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and link brackets are used to safely maneuver the heavy transmission components.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. The document outlines 51 steps to assemble the individual components of a torque converter, including installing seals, bearings, gears, housings, and fasteners in the proper order and with specified torques.
2. Tools and torque specifications are provided for each step to ensure correct assembly.
3. The final step is to connect the assembled torque converter to the transmission and transfer gears to complete the power train.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and link brackets are used to safely maneuver the heavy transmission components.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and link brackets are used to safely maneuver the heavy transmission components.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, housings and other components. It also describes how to separate a transmission from output transfer gears, including disconnecting harnesses and tubes, and removing housing and manifold components. The process is illustrated through 41 figures.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
This document provides instructions for disassembling the components of a 988K wheel loader torque converter. It lists over 60 individual steps to remove parts like the housing assembly, shaft assembly, carrier assembly, impeller, piston, seals, bearings, and other internal components. Detailed illustrations accompany each step. Special tools are required to separate certain components, and safety precautions are noted due to the heavy weight of assemblies that need to be lifted out.
This document provides disassembly instructions for a 986H wheel loader transmission planetary system in 3 sentences or less:
The document outlines 75 steps to disassemble the transmission planetary system, removing components like planetary gears, clutch housings, pistons, seals, and other parts. Tools required include a transmission repair stand, eyebolts, clamps, retaining ring pliers, external pliers, drivers, and other specialized tools to aid in disassembly. Cleanliness is emphasized as dirt could enter the transmission during disassembly.
More Related Content
Similar to Caterpillar Cat 980H Wheel Loader (Prefix PF8) Service Repair Manual (PF800001 and up).pdf
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps to assemble the torque converter components and attach it to the transmission housing. It then describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, disconnecting electrical and hydraulic lines, and lifting components with the specified tools. The purpose is to connect or separate the torque converter, transmission, and output transfer gears on a 980M wheel loader.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Proper tools and torque specifications are listed. Finally, it states to connect the assembled torque converter to the transmission and output transfer gears.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important, as is applying clean hydraulic oil and torquing bolts to specified values.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps to assemble the torque converter components and attach it to the transmission housing. It then describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, disconnecting electrical and hydraulic lines, and lifting components with the specified tools. The purpose is to connect or separate the torque converter, transmission, and output transfer gears on a 980M wheel loader.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important, as is applying clean hydraulic oil and torquing bolts to specified values.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps for installing various components like seals, bearings, gears, and housing pieces. It also describes using specialty tools and proper torque specifications. Separately, it outlines 5 steps for removing a transmission from output transfer gears, which involves lifting components, disconnecting lines, and removing bolts.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important during assembly. Finally, the manual specifies torques for fasteners and checking bearing end play.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important during assembly. Finally, the manual specifies torques for fasteners and checking bearing end play.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps for installing various components like seals, bearings, gears, and housing pieces. It also describes using specialty tools and proper torque specifications. Finally, it explains how to separate the transmission from the output transfer gears by removing bolts, disconnecting lines, and lifting components with brackets.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install internal components like thrust bearings and seals in sequential order into the housing.
2. Heat critical components like bearings to specific temperatures and install carefully. Attach the drive components including impeller, turbine, and stator.
3. Secure the housing cover and install external mounting brackets and hardware. Check clearances and lubricate seals before final assembly.
This document provides assembly instructions for connecting a torque converter to a transmission and output transfer gears on a 980G wheel loader. The procedure involves 62 steps, including installing various components like an output shaft, O-rings, and link brackets. Tools required include a stand, link brackets, and dial indicators. Cleanliness is important during assembly and all parts must be inspected for wear before installation.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and tools are used to safely handle components weighing up to 1406 kg.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and link brackets are used to safely maneuver the heavy transmission components.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. The document outlines 51 steps to assemble the individual components of a torque converter, including installing seals, bearings, gears, housings, and fasteners in the proper order and with specified torques.
2. Tools and torque specifications are provided for each step to ensure correct assembly.
3. The final step is to connect the assembled torque converter to the transmission and transfer gears to complete the power train.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and link brackets are used to safely maneuver the heavy transmission components.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and link brackets are used to safely maneuver the heavy transmission components.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, housings and other components. It also describes how to separate a transmission from output transfer gears, including disconnecting harnesses and tubes, and removing housing and manifold components. The process is illustrated through 41 figures.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
Similar to Caterpillar Cat 980H Wheel Loader (Prefix PF8) Service Repair Manual (PF800001 and up).pdf (20)
This document provides instructions for disassembling the components of a 988K wheel loader torque converter. It lists over 60 individual steps to remove parts like the housing assembly, shaft assembly, carrier assembly, impeller, piston, seals, bearings, and other internal components. Detailed illustrations accompany each step. Special tools are required to separate certain components, and safety precautions are noted due to the heavy weight of assemblies that need to be lifted out.
This document provides disassembly instructions for a 986H wheel loader transmission planetary system in 3 sentences or less:
The document outlines 75 steps to disassemble the transmission planetary system, removing components like planetary gears, clutch housings, pistons, seals, and other parts. Tools required include a transmission repair stand, eyebolts, clamps, retaining ring pliers, external pliers, drivers, and other specialized tools to aid in disassembly. Cleanliness is emphasized as dirt could enter the transmission during disassembly.
This document provides disassembly instructions for the transmission planetary of a 986H wheel loader. It outlines 59 steps to fully disassemble the transmission, including removing planetary gears, clutch housings, pistons, seals, gears, and other components. Tools required include a transmission repair stand, eyebolts, clamps, retaining ring pliers, external pliers, drivers, and slide hammers. Detailed illustrations accompany each step. Safety precautions are provided to prevent injury from released spring forces.
This document provides assembly instructions for a torque converter in a 982M wheel loader. It outlines 51 steps to assemble the internal components of the torque converter and attach it to the transmission and output transfer gears. The instructions include installing seals, bearings, gears, plates, springs, and bolts. Tolerances and torque specifications are provided. The final step is to connect the assembled torque converter to the transmission and output transfer gears.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 982M Wheel Loader. It outlines 51 steps requiring various tools to install seals, bearings, gears, plates, and bolts in the specified order and torque. The process connects the assembled torque converter to the transmission and output transfer gears.
The document provides instructions for assembling and disassembling components of a 982M wheel loader transmission powered by a C13 engine. It describes 51 steps to assemble the torque converter lock up clutch and freewheel stator. It also describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, harnesses, tubes, and solenoids. Tools including levers, links, and stands are required. Weights of components are provided.
This document provides disassembly and assembly instructions for the torque converter of a 982M wheel loader. It details 46 steps to disassemble components such as the torque converter housing, pump adapter, gears, bearings and seals. It then lists 45 steps for assembly, installing components in reverse order and noting specific details like orientation and lubrication of parts. Tools required are listed in a table.
1. The document provides disassembly and assembly instructions for the lock up clutch and freewheel stator of a 980M wheel loader torque converter.
2. It lists 46 steps to disassemble components and 45 steps to reassemble them, including the use of various tools.
3. The components include housing, gears, seals, bearings, plates, disks, and more that make up the internal workings of the torque converter and transmission.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps to install various components like seals, bearings, gears, and housings. Finally, it specifies connecting the assembled torque converter to the transmission and output transfer gears.
This document provides assembly instructions for a piston pump on a 980L wheel loader. It describes installing various components like bearings, seals, retainers and pistons. It also provides steps to determine proper shim thickness and clearance between parts. The goal is to assemble the pump with specified end play, sliding block play and timing between components.
The document provides step-by-step instructions for assembling a torque converter for a 980M wheel loader. It details 51 steps for installing various components like seals, bearings, gears, and housings. Proper tools and torque specifications are listed to ensure correct assembly.
This document provides disassembly instructions for the planetary transmission of a 972H wheel loader. It lists 50 steps to fully disassemble the transmission, including removing gears, shafts, housings, seals, and other internal components. Detailed illustrations accompany each step to show how to properly disassemble the transmission in the correct order. Safety precautions are provided to warn of potential spring hazards during disassembly.
This document provides disassembly instructions for a 992K wheel loader torque converter. It lists over 50 individual steps to disassemble the various components of the torque converter housing assembly, including removing pumps, gears, seals, bearings, and other internal parts. Detailed illustrations accompany each step to show how to position the assembly, what tools are needed, and how to separate the individual components. The overall process involves disassembling the entire torque converter and transmission housing to access all internal parts.
This document provides instructions for disassembling the components of a 992K wheel loader torque converter. It describes removing over 20 individual parts in multiple steps, including the torque converter, modulating valves, pumps, gears, housings, clutches and bearings. Cleanliness is emphasized throughout to prevent contamination. Various tools are required and safety precautions mentioned due to components weighing up to 680kg.
This document provides instructions for disassembling the transmission and torque converter of a 924G or 924Gz wheel loader. It lists the required tools and gives step-by-step instructions to remove components such as gears, seals, plates, discs, bearings, and clutches. Safety precautions are provided for releasing clutch springs. The disassembly process is described in detail through 50 steps and accompanied by illustrations of each step.
The document provides instructions for disassembling and assembling the vane pump used in the steering system of a 657G Wheel Scraper. It describes in detail removing each individual component of the pump including housing, seals, cartridge, rotor, vanes and shaft. Fifteen detailed steps are outlined for disassembly, requiring basic tools like retaining ring pliers and a bearing puller. Similarly, sixteen steps are provided for reassembling the pump and installing it back into the steering system. Proper cleaning and lubrication of parts is emphasized to prevent contamination.
This document provides instructions for disassembling a torque converter for a 988K wheel loader. It lists over 60 individual steps to remove components such as housing assemblies, shafts, bearings, seals, gears, and plates. Special tools are required for tasks like separating housings and pulling components. Precautions include using lifting devices and cribbing due to component weights up to 545 kg. Detailed illustrations accompany each step.
This service repair manual provides instructions for disassembling a 988H wheel loader torque converter. It lists 72 steps and required tools to remove all components of the torque converter. Key parts that are dismantled include the housing assembly, carrier assembly, turbine, impeller, stator, shafts, gears, seals, and bearings. Detailed illustrations accompany each step to show how to properly disassemble the torque converter.
This service repair manual provides instructions to disassemble the transmission planetary of a 986H wheel loader model. It outlines 57 steps to fully disassemble the transmission components, including removing planetary gears, clutch housings, pistons, seals, gears, and other parts. Detailed illustrations accompany each step to show how to properly remove each component. Safety precautions are provided throughout to prevent injury from heavy parts or released spring forces during disassembly.
The document provides instructions for disassembling and assembling the final drive and sprocket of a 973K track loader. It lists the required tools and parts. The disassembly process involves removing the final drive, sprocket segments, covers, gears, shafts, seals, and bearings. The assembly process reverses the disassembly steps and provides details on heating and positioning components, applying sealant, and tightening fasteners to the specified torques.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980H WHEEL LOADER PF8
Configuration: 980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
980H Wheel Loader
Power Train
Media Number -UENR3319-00 Publication Date -01/02/2014 Date Updated -04/02/2014
i05584317
Torque Converter - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 3
B
8T-5096 Dial Indicator Gp 1
5P-2390 Gauge Tool Gp 1
C 1P-0520 Driver Gp 1
D -
Guide Stud
3/8 - 16 by 6 in
2
E -
Guide Stud
1/2 - 13 by 6 in
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Apply oil to all of the bearings before assembly.
1/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g03543396
1. Use Tooling (C) in order to install sleeve bearing (79) in cover assembly (77). Sleeve
bearing (79) must be even with the outside surface of cover assembly (77) .
Illustration 2 g03543183
2. Install cover assembly (77) to rotating housing (54) .
3. Install ring seal (78) to rotating housing (54) .
4. Install bolts (76) and the washers. Tighten bolts (76) to a torque of 30 ± 5 N·m (22 ± 4 lb ft).
2/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 8. Install bolts (71) and the washers. Tighten bolts (71) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
Illustration 6 g03543017
9. Install turbine hub (69) and converter turbine (70) as a unit to rotating housing (54) .
Illustration 7 g03543002
10. Install thrust bearing race (68), thrust bearing (67), and thrust bearing race (66) .
4/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g03545378
11. Use Tooling (C) in order to install sleeve bearing (65) to carrier assembly (61). Sleeve
bearing (65) must be even with the counterbore of carrier assembly (61) .
Illustration 9 g03542979
12. Install retaining ring (64) in stator (63) .
Illustration 10 g03542936
13. Raise the temperature of stator (63) .
14. Install stator (63) onto carrier assembly (61) .
5/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g03542917
15. Install snap ring (62) .
Illustration 12 g03542898
16. Install the stator and carrier assembly (61) as a unit to rotating housing (54) .
Illustration 13 g03542876
17. Install thrust bearing race (60), thrust bearing (59), and thrust bearing race (58) .
6/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g03542819
21. Install bolts (55) to drive flange (53). Tighten bolts (55) to a torque of 80 ± 10 N·m (59 ± 7
lb ft).
Illustration 17 g03542001
22. Use two people in order to install drive flange (53) on rotating housing (54). The weight of
drive flange (53) is approximately 23 kg (51 lb).
23. Install bolts (52) and the washers. Tighten bolts (52) to a torque of 30 ± 5 N·m (22 ± 4 lb ft).
Illustration 18 g03545936
24. Lower the temperature of outer bearing race (51) .
25. Install outer bearing race (51) into drive gear (50).
8/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 19 g03541957
26. Install drive gear (50). Install bolts (49) and the washers. Tighten bolts (49) to a torque of 50
± 7 N·m (37 ± 5 lb ft).
Illustration 20 g03546276
27. Raise the temperature of inner bearing (48) .
28. Install inner bearing (48) onto bearing carrier (42) .
9/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g03541898
29. Install retaining ring (47) onto bearing carrier (42) .
Illustration 22 g03546297
30. Raise the temperature of ring carrier (46) .
31. Install ring carrier (46) onto bearing carrier (42) .
Illustration 23 g03541664
32. Install seal ring (45) onto ring carrier (46) .
33. Install O-ring seal (44) on bearing carrier (42)
10/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 36. Install retaining ring (38) into the groove of idler gear (28) .
Illustration 27 g03546416
37. Lower the temperature of bearing cup (39) .
38. Install bearing cup (39) into idler gear (28) .
Illustration 28 g03541116
39. Flip idler gear (28) to the opposite side. Install bearing cup spacer (37) in idler gear (28).
The notch in bearing cup spacer (37) must be aligned with the retaining ring.
12/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 29 g03546456
40. Lower the temperature of bearing cup (36) .
41. Install bearing cup (36) into idler gear (28) .
Illustration 30 g03540968
42. Install bearing cone (35) , bearing cone spacer (34), and bearing cone (33) in idler gear
(28) .
13/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 31 g03540776
43. Install O-ring seal (32) and ball (31) to shaft assembly (29) .
Illustration 32 g03546532
44. Install O-ring seal (30) to torque converter cover (3) .
45. Install idler gear (28) and shaft assembly (29) (not show) to torque converter cover (3) .
46. Install bolt (27) and the washer. Tighten bolt (27) to a torque of 120 ± 20 N·m (89 ± 15 lb
ft).
Illustration 33 g03541363
Improper assembly of parts that are spring loaded can cause bodily
injury.
14/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
47. Install poppet (23), spring (24), retainer (25), retaining ring (26), and spacers (22) into spool
(21) .
Illustration 34 g03541319
48. Install spool (21) and spring (20) into relief valve assembly (16) .
Illustration 35 g03541281
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
15/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 49. Install the O-ring seal, cover (18), and the bolts. Repeat this step for the opposite side.
50. Install the O-ring seal and fitting (19) .
Illustration 36 g03541236
51. Install O-ring seals (17) to relief valve assembly (16) .
Illustration 37 g03541198
52. Position relief valve (16) to torque converter cover (3). Install bolts (15) and the washers.
16/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 38 g03540719
53. Lower the temperature of bearing cup (14) .
54. Install bearing cup (14) to torque converter cover (3) .
Illustration 39 g03546602
55. Raise the temperature of bearing cone (13) .
56. Install bearing cone (13) to pump drive gear (12) .
17/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 40 g03540096
57. Install pump drive gear (12) into torque converter cover (3) .
Illustration 41 g03540077
58. Lower the temperature of bearing cup (9) .
59. Install bearing cup (9) to pump adapter (8) .
60. Install shims (10) to pump adapter (8) .
61. Apply clean hydraulic oil to O-ring seal (11). Install O-ring seal (9) .
Illustration 42 g03546659
62. Install Tooling (D) to torque converter cover (3). Use Tooling (D) in order to guide pump
adapter (8) into position on torque converter cover (3) .
18/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 43 g03546663
63. Install bolts (7) and the washers.
64. Use Tooling (B) in order to check bearing end play. The bearing end play must be 0.15 ±
0.05 mm (0.006 ± 0.002 inch). Add or remove shims in order to get the correct bearing end
play.
Note: If end play is less than 0.10 mm (0.004 inch), add additional shims. If end play is
greater than 0.20 mm (0.008 inch), remove shims.
Illustration 44 g03548097
65. Install the O-ring seal, adapter (6), the washers, and the bolts.
19/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 45 g03539953
66. Install elbow (5). Install O-ring seal (4) .
Illustration 46 g03547436
67. Install Tooling (E) .
68. Attach Tooling (A) and a suitable lifting device to torque converter cover (3). The weight of
torque converter cover (3) is approximately 120 kg (265 lb). Use Tooling (A) and the
suitable lifting device in order to install torque converter cover (3) on the torque converter.
20/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 47 g03539596
69. Install bolts (2) and the washers. Tighten bolts (2) to a torque of 120 ± 20 N·m (89 ± 15 lb
ft). Install output shaft (1) .
End By: Connect the torque converter to the transmission and the output gears.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Mar 20 17:22:08 UTC+0800 2021
21/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980H WHEEL LOADER PF8
Configuration: 980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
980H Wheel Loader
Power Train
Media Number -UENR3319-00 Publication Date -01/02/2014 Date Updated -04/02/2014
i02187020
Transmission from Output Transfer Gears - Separate
SMCS - 3002-076
Separation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 138-7575 Link Bracket 1
C 138-7575 Link Bracket 3
Start By:
a. Separate the torque converter from the transmission. Refer to Disassembly and Assembly,
"Torque Converter from Transmission, Output Transfer Gears - Separate".
1/4
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g01105945
Illustration 2 g01105953
1. Use Tooling (A), Tooling (B) and a suitable lifting device in order to reposition the
transmission and output transfer gears (1) onto suitable cribbing. The weight of the
transmission and output transfer gears (1) is approximately 1406 kg (3100 lb).
Illustration 3 g01105947
2/4
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 6 g01105978
5. Attach Tooling (C) and a suitable lifting device to transmission (6). The weight of
transmission (6) is approximately 726 kg (1600 lb). Remove bolts (7). Do not remove the
two smaller bolts (8).
Illustration 7 g01105986
6. Use the suitable lifting device in order to remove transmission (6).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Mar 20 17:23:05 UTC+0800 2021
4/4
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980H WHEEL LOADER PF8
Configuration: 980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
980H Wheel Loader
Power Train
Media Number -UENR3319-00 Publication Date -01/02/2014 Date Updated -04/02/2014
i05593710
Output Transfer Gears - Disassemble
SMCS - 3075-015-OJ
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
B
8B-7548 Push-Puller Tool Gp 1
8B-7551 Bearing Puller Gp 1
9S-9154 Step Plate 1
C 439-3940 Bracket As 2
D -
Forcing Bolt
3/8 - 16 by 6 in
2
Start By:
A. Remove the transmission from the output transfer gears.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/17
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 3 g01108605
3. Remove bolt (3) and retainer (4) from the input side of the output transfer gear case.
Illustration 4 g01108617
4. Remove O-ring seal (5) .
Illustration 5 g01108628
5. Remove yoke (6) .
3/17
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
31. Illustration 6 g01108630
6. Remove bolts (7) and the washers from bearing cage (8) .
Illustration 7 g01108631
7. Use Tooling (D) in order to remove bearing cage (8) .
Illustration 8 g01108635
4/17
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. 8. Use Tooling (A) in order to remove lip seal (9) and outer bearing race (10) from bearing
cage (8) .
Illustration 9 g01108639
9. Remove O-ring seal (11) from bearing cage (8) .
Illustration 10 g01108665
10. Remove spacer (12) from transfer shaft (13) .
5/17
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Illustration 11 g01108680
11. Position the transfer case with the output side upward, as shown. The weight of the output
transfer gear group is 526 kg (1160 lb).
12. Mark bolts (14) for installation purposes. Remove bolts (14) and the washers from bearing
cage (15) .
13. Use Tooling (D) in order to loosen bearing cage (15) from the transfer case. Remove
bearing cage (15) .
Illustration 12 g01108700
14. Position bearing cage (15) onto a suitable press. The combined weight of bearing cage (15)
and transfer shaft (13) is approximately 61 kg (135 lb). Use the suitable press in order to
press transfer shaft (13) out of bearing cage (15) .
Note: Place a suitable block (not shown) under transfer shaft (13) in order to prevent
transfer shaft (13) from falling to the ground.
6/17
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...