This service manual provides instructions for assembling the torque converter of a 980H wheel loader. It details 69 assembly steps requiring various tools. The torque converter connects the engine to the transmission and output gears. Key components include the rotating housing, stator, carrier assembly, impeller, turbine, and torque converter cover. Precise assembly is needed to ensure proper bearing end play and component alignment.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides disassembly instructions for a torque converter in 3 steps:
1. Remove the torque converter housing from the transmission.
2. Disassemble the internal components of the torque converter housing.
3. Clean all torque converter parts thoroughly before inspection and assembly.
This document provides disassembly instructions for a torque converter in 3 steps:
1. Remove the torque converter housing from the transmission.
2. Disassemble the internal components of the torque converter housing.
3. Clean all torque converter parts thoroughly before inspection and assembly.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, races, and gears in the specified order while following torque specifications.
2. Install the stator, carrier assembly, impeller, and drive flange. Fit the idler gear, shaft assembly, and pump drive gear into the torque converter housing.
3. Attach the pump adapter and check bearing end play using gauges before applying the final seal.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, and gears in sequential order while applying specified torques to fasteners.
2. Heat certain parts like bearings to specified temperatures before installation. Install the stator and ensure proper contact and positioning of components.
3. Attach the pump adapter and install guide pins to hold parts in place before removing them after installation is complete.
This document provides disassembly instructions for a torque converter in 3 steps:
1. Remove the torque converter housing from the transmission.
2. Disassemble the internal components of the torque converter housing.
3. Clean all torque converter parts thoroughly before inspection and assembly.
This document provides disassembly instructions for a torque converter in 3 steps:
1. Remove the torque converter housing from the transmission.
2. Disassemble the internal components of the torque converter housing.
3. Clean all torque converter parts thoroughly before inspection and assembly.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install various internal components like sleeves, seals, races, and gears in the specified order while following torque specifications.
2. Install the stator, carrier assembly, impeller, and drive flange. Fit the idler gear, shaft assembly, and pump drive gear into the torque converter housing.
3. Attach the pump adapter and check bearing end play using gauges before applying the final seal.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps to assemble the torque converter components and attach it to the transmission housing. It then describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, disconnecting electrical and hydraulic lines, and lifting components with the specified tools. The purpose is to connect or separate the torque converter, transmission, and output transfer gears on a 980M wheel loader.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Proper tools and torque specifications are listed. Finally, it states to connect the assembled torque converter to the transmission and output transfer gears.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important, as is applying clean hydraulic oil and torquing bolts to specified values.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps to assemble the torque converter components and attach it to the transmission housing. It then describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, disconnecting electrical and hydraulic lines, and lifting components with the specified tools. The purpose is to connect or separate the torque converter, transmission, and output transfer gears on a 980M wheel loader.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important, as is applying clean hydraulic oil and torquing bolts to specified values.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps for installing various components like seals, bearings, gears, and housing pieces. It also describes using specialty tools and proper torque specifications. Separately, it outlines 5 steps for removing a transmission from output transfer gears, which involves lifting components, disconnecting lines, and removing bolts.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important during assembly. Finally, the manual specifies torques for fasteners and checking bearing end play.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important during assembly. Finally, the manual specifies torques for fasteners and checking bearing end play.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps for installing various components like seals, bearings, gears, and housing pieces. It also describes using specialty tools and proper torque specifications. Finally, it explains how to separate the transmission from the output transfer gears by removing bolts, disconnecting lines, and lifting components with brackets.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install internal components like thrust bearings and seals in sequential order into the housing.
2. Heat critical components like bearings to specific temperatures and install carefully. Attach the drive components including impeller, turbine, and stator.
3. Secure the housing cover and install external mounting brackets and hardware. Check clearances and lubricate seals before final assembly.
This document provides assembly instructions for connecting a torque converter to a transmission and output transfer gears on a 980G wheel loader. The procedure involves 62 steps, including installing various components like an output shaft, O-rings, and link brackets. Tools required include a stand, link brackets, and dial indicators. Cleanliness is important during assembly and all parts must be inspected for wear before installation.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and tools are used to safely handle components weighing up to 1406 kg.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and link brackets are used to safely maneuver the heavy transmission components.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. The document outlines 51 steps to assemble the individual components of a torque converter, including installing seals, bearings, gears, housings, and fasteners in the proper order and with specified torques.
2. Tools and torque specifications are provided for each step to ensure correct assembly.
3. The final step is to connect the assembled torque converter to the transmission and transfer gears to complete the power train.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and link brackets are used to safely maneuver the heavy transmission components.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and link brackets are used to safely maneuver the heavy transmission components.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, housings and other components. It also describes how to separate a transmission from output transfer gears, including disconnecting harnesses and tubes, and removing housing and manifold components. The process is illustrated through 41 figures.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
Caterpillar Cat CP-663E Vibratory Compactor (Prefix AEF) Service Repair Manua...ujkfdkkmsmd
This document provides disassembly and assembly instructions for a piston pump used in vibratory compactors. It describes 41 steps to fully disassemble the pump into individual components. This includes removing seals, springs, valves, pistons, plates, blocks, bearings and other parts. Similarly, it lists 41 steps for reassembling all the components in the reverse order. Cleanliness is emphasized throughout the process.
Caterpillar Cat CP-583E Vibratory Compactor (Prefix CNX) Service Repair Manua...ujkfdkkmsmd
This document provides instructions for removing and installing piston cooling jets, pistons, connecting rods, and related components on a Caterpillar 3056E engine. The removal process involves taking out the engine oil pan, removing valve assemblies from the piston cooling jets, and pushing pistons and connecting rods out of the cylinder block. The installation process requires cleaning components, lubricating them with oil, and reinserting pistons and connecting rods into the cylinder block before replacing other parts. Safety notices are provided to keep components clean and contain fluids.
More Related Content
Similar to Caterpillar Cat 980H Wheel Loader (Prefix PF8) Service Repair Manual (PF800001 and up).pdf
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps to assemble the torque converter components and attach it to the transmission housing. It then describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, disconnecting electrical and hydraulic lines, and lifting components with the specified tools. The purpose is to connect or separate the torque converter, transmission, and output transfer gears on a 980M wheel loader.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Proper tools and torque specifications are listed. Finally, it states to connect the assembled torque converter to the transmission and output transfer gears.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important, as is applying clean hydraulic oil and torquing bolts to specified values.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps to assemble the torque converter components and attach it to the transmission housing. It then describes 5 steps to separate the transmission from the output transfer gears, including removing bolts, disconnecting electrical and hydraulic lines, and lifting components with the specified tools. The purpose is to connect or separate the torque converter, transmission, and output transfer gears on a 980M wheel loader.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important, as is applying clean hydraulic oil and torquing bolts to specified values.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps for installing various components like seals, bearings, gears, and housing pieces. It also describes using specialty tools and proper torque specifications. Separately, it outlines 5 steps for removing a transmission from output transfer gears, which involves lifting components, disconnecting lines, and removing bolts.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important during assembly. Finally, the manual specifies torques for fasteners and checking bearing end play.
This service repair manual provides instructions for assembling the lock up clutch and freewheel stator for the torque converter in a 980M wheel loader. It outlines 51 steps for installing various components like seals, bearings, gears, and housings. Tools required include link brackets, dial indicators, retaining ring pliers, and guide studs. Proper heating and cooling of components is important during assembly. Finally, the manual specifies torques for fasteners and checking bearing end play.
The document provides instructions for assembling a torque converter and connecting it to a transmission. It lists 51 steps for installing various components like seals, bearings, gears, and housing pieces. It also describes using specialty tools and proper torque specifications. Finally, it explains how to separate the transmission from the output transfer gears by removing bolts, disconnecting lines, and lifting components with brackets.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. Clean all parts thoroughly before assembly and apply oil to bearings. Install internal components like thrust bearings and seals in sequential order into the housing.
2. Heat critical components like bearings to specific temperatures and install carefully. Attach the drive components including impeller, turbine, and stator.
3. Secure the housing cover and install external mounting brackets and hardware. Check clearances and lubricate seals before final assembly.
This document provides assembly instructions for connecting a torque converter to a transmission and output transfer gears on a 980G wheel loader. The procedure involves 62 steps, including installing various components like an output shaft, O-rings, and link brackets. Tools required include a stand, link brackets, and dial indicators. Cleanliness is important during assembly and all parts must be inspected for wear before installation.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and tools are used to safely handle components weighing up to 1406 kg.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and link brackets are used to safely maneuver the heavy transmission components.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
This document provides assembly instructions for a torque converter in 3 steps or less:
1. The document outlines 51 steps to assemble the individual components of a torque converter, including installing seals, bearings, gears, housings, and fasteners in the proper order and with specified torques.
2. Tools and torque specifications are provided for each step to ensure correct assembly.
3. The final step is to connect the assembled torque converter to the transmission and transfer gears to complete the power train.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and link brackets are used to safely maneuver the heavy transmission components.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, bearings, plates and other components. The summary separates the transmission from the output transfer gears by removing housings, bolts, solenoids and disconnecting wiring and tubes. Lifting devices and link brackets are used to safely maneuver the heavy transmission components.
This document provides assembly instructions for connecting a torque converter to a transmission in a 980M wheel loader. It outlines 51 steps to assemble seals, gears, shafts, housings and other components. It also describes how to separate a transmission from output transfer gears, including disconnecting harnesses and tubes, and removing housing and manifold components. The process is illustrated through 41 figures.
This document provides assembly instructions for a torque converter in 3 steps:
1. It describes 51 assembly steps to install various components like seals, bearings, gears, and housings onto the torque converter.
2. It instructs to connect the assembled torque converter to the transmission and output transfer gears.
3. It lists the required tools and provides illustrations for each assembly step.
Similar to Caterpillar Cat 980H Wheel Loader (Prefix PF8) Service Repair Manual (PF800001 and up).pdf (20)
Caterpillar Cat CP-663E Vibratory Compactor (Prefix AEF) Service Repair Manua...ujkfdkkmsmd
This document provides disassembly and assembly instructions for a piston pump used in vibratory compactors. It describes 41 steps to fully disassemble the pump into individual components. This includes removing seals, springs, valves, pistons, plates, blocks, bearings and other parts. Similarly, it lists 41 steps for reassembling all the components in the reverse order. Cleanliness is emphasized throughout the process.
Caterpillar Cat CP-583E Vibratory Compactor (Prefix CNX) Service Repair Manua...ujkfdkkmsmd
This document provides instructions for removing and installing piston cooling jets, pistons, connecting rods, and related components on a Caterpillar 3056E engine. The removal process involves taking out the engine oil pan, removing valve assemblies from the piston cooling jets, and pushing pistons and connecting rods out of the cylinder block. The installation process requires cleaning components, lubricating them with oil, and reinserting pistons and connecting rods into the cylinder block before replacing other parts. Safety notices are provided to keep components clean and contain fluids.
Caterpillar Cat CP-573E Vibratory Compactor (Prefix CEB) Service Repair Manua...ujkfdkkmsmd
The document provides instructions for removing and installing the final drive planetary and piston motor components on a CS-573E and CP-573E vibratory compactor. It describes using various tools to disassemble components like the housing, hub, gears, seals and installing new components in the reverse order. Precise torques and clear illustrations are provided to correctly assemble the final drive planetary.
Caterpillar Cat CP-563D Vibratory Compactors (Prefix 2RZ) Service Repair Manu...ujkfdkkmsmd
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on CP-563D and CS-563D vibratory compactors powered by a 3116 engine. The removal procedure involves using a valve seat extractor tool to expand below the edge of the valve seat insert in order to remove it from the cylinder head. The installation procedure refers to ensuring parts are clean and checking guidelines for determining if valve seats can be reused.
Caterpillar Cat CP-533E Vibratory Compactor (Prefix ASL) Service Repair Manua...ujkfdkkmsmd
This document provides instructions for disassembling and assembling the piston pump used for drum propulsion on vibratory compactor models CS-533E and CP-533E. The disassembly procedure involves removing 28 components from the pump in 12 steps using various tools. Cleaning and inspecting parts is emphasized before reassembly in the reverse order over 28 steps.
Caterpillar Cat CP-533D Vibratory Compactor (Prefix AET) Service Repair Manua...ujkfdkkmsmd
This document provides instructions for removing and installing inlet and exhaust valve guides on a CS-533D and CP-533D vibratory compactor. It outlines the required tools and gives step-by-step instructions for removing the old guides and pressing new guides into the cylinder head assembly. Proper cleaning and lubrication of parts is emphasized to prevent premature wear. Reusability guidelines for different components are also referenced.
Caterpillar Cat CP-433E Vibratory Compactor (Prefix DAC) Service Repair Manua...ujkfdkkmsmd
The document provides instructions for assembling and disassembling various components of a vibratory compactor model CS-433E or CP-433E, including:
- Assembling the piston motor drum propel system in 24 steps requiring various tools.
- Installing the assembled piston motor drum propel system with 2 illustrations.
- Removing the final drive planetary from the drum propel in 7 steps requiring lifting tools and draining the oil first.
This document provides disassembly instructions for the final drive of a 5110B mining excavator. It lists the required tools and steps to disassemble the various components of the final drive. The major steps include removing the gears, carriers, housings and other components using specialized tools like pullers and presses. Cleanliness is emphasized to prevent contamination of hydraulic components during disassembly and reassembly.
Caterpillar Cat CB534B Roller Service Repair Manual.pdfujkfdkkmsmd
This document provides instructions for replacing the propel speed range switch on models CB534B and CB534C rollers. It describes removing the operator station panel assembly, propel speed range switch, and associated wires and lockwashers. It then describes installing the new propel speed range switch with wires and lockwashers and reinstalling the panel assembly.
Caterpillar Cat CB534C Roller Service Repair Manual.pdfujkfdkkmsmd
This document provides instructions for replacing the propel speed range switch on models CB534B and CB534C rollers. It describes removing the operator station panel assembly, propel speed range switch, and associated wires and lockwashers. It then describes installing the new propel speed range switch with wires and lockwashers and reinstalling the panel assembly.
This document provides disassembly instructions for the final drive of a 5110B mining excavator. It outlines 33 steps to fully disassemble the final drive, including removing gears, carriers, housings, seals, bearings, and other components. Special tools are required and cleanliness is important to prevent contamination of parts. The document emphasizes safety precautions due to heavy component weights and potential for flying debris or released spring forces during disassembly.
Caterpillar Cat 5080 FRONT SHOVEL (Prefix 8SL) Service Repair Manual (8SL0000...ujkfdkkmsmd
This document provides instructions for removing and installing fuel injection nozzles and adapters on a 5080 FRONT SHOVEL excavator with a 3406B engine. It describes using various tools to disconnect fuel lines, remove retainers and nozzles, and clean parts. Detailed steps are given for installing nozzles, adapters, seals and applying lubricants. Similar level of detail is provided for removing and installing the cylinder head assembly, spacer plate, and valves.
This document provides disassembly instructions for a 992K wheel loader torque converter. It lists over 50 individual steps to disassemble the various components of the torque converter housing assembly, including removing pumps, gears, seals, bearings, and other internal parts. Detailed illustrations accompany each step to show how to position the assembly, what tools are needed, and how to separate the individual components. The overall process involves disassembling the entire torque converter and transmission housing to access all internal parts.
This document provides instructions for servicing the power train components of a 992B wheel loader, including removing and installing axles, final drive carriers, ring gears, hubs, wheels, and wheel brakes. The document is divided into several sections covering different components, and each section provides detailed step-by-step instructions and diagrams for disassembly and assembly of the specified components. Safety precautions and notes are included throughout.
This document provides disassembly instructions for a 992K wheel loader torque converter. It describes removing 57 individual components through a step-by-step process involving specialized tools. Key parts that must be removed include the torque converter housing, pump adapter, idler gear, housing assembly, pump drive gear, turbine assembly, impeller clutch, and shaft assembly. Precise instructions are given for each removal to ensure safety and prevent damage to precision components.
This document provides instructions for servicing the power train components of a Caterpillar 992B wheel loader, including removing and installing axles, final drive carriers, ring gears, hubs, wheels, and wheel brakes. The steps describe using hoists and tools to remove heavy components and reassemble them in reverse order. Weights of removed parts are provided to aid technicians performing the work.
This document provides disassembly instructions for the transmission planetary system of a 992G wheel loader. It outlines 52 steps to fully disassemble the transmission, including removing components like the transmission case assembly, end plates, clutches, planetary carrier, and sun gear. Various tools are required to separate, remove, and disassemble the different transmission parts. Detailed illustrations accompany each step to show how to properly disassemble the transmission planetary.
This document provides disassembly instructions for the transmission planetary of a 992G wheel loader. It lists 57 steps to fully disassemble the transmission planetary, including removing components like the transmission case assembly, carrier assembly, clutch housings, and planetary gears. Detailed illustrations accompany each step to show how to remove seals, bolts, springs, and other parts. Special tools are required for tasks like separating transmission components and removing bearings.
This document provides instructions for removing and installing an electronic unit injector on a Caterpillar 3508 engine. It describes:
1. Removing the rocker shaft assembly, pushrods, clamps and bolts to remove the injector.
2. Cleaning the cylinder head bore before installing the new injector.
3. Installing the injector, connecting the harness, and reinstalling removed components.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3412E engine. It lists the required tools and gives step-by-step details of the removal and installation process. The removal process involves detaching hoses, bolts, and manifolds. Lifting devices are needed due to the heavy weight of parts. The installation process reverses the removal steps and provides tightening specifications for bolts. Precautions are given to keep parts clean and apply lubricants to seals.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980H WHEEL LOADER PF8
Configuration: 980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
980H Wheel Loader
Power Train
Media Number -UENR3319-00 Publication Date -01/02/2014 Date Updated -04/02/2014
i05584317
Torque Converter - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 3
B
8T-5096 Dial Indicator Gp 1
5P-2390 Gauge Tool Gp 1
C 1P-0520 Driver Gp 1
D -
Guide Stud
3/8 - 16 by 6 in
2
E -
Guide Stud
1/2 - 13 by 6 in
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Apply oil to all of the bearings before assembly.
1/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g03543396
1. Use Tooling (C) in order to install sleeve bearing (79) in cover assembly (77). Sleeve
bearing (79) must be even with the outside surface of cover assembly (77) .
Illustration 2 g03543183
2. Install cover assembly (77) to rotating housing (54) .
3. Install ring seal (78) to rotating housing (54) .
4. Install bolts (76) and the washers. Tighten bolts (76) to a torque of 30 ± 5 N·m (22 ± 4 lb ft).
2/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 8. Install bolts (71) and the washers. Tighten bolts (71) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
Illustration 6 g03543017
9. Install turbine hub (69) and converter turbine (70) as a unit to rotating housing (54) .
Illustration 7 g03543002
10. Install thrust bearing race (68), thrust bearing (67), and thrust bearing race (66) .
4/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g03545378
11. Use Tooling (C) in order to install sleeve bearing (65) to carrier assembly (61). Sleeve
bearing (65) must be even with the counterbore of carrier assembly (61) .
Illustration 9 g03542979
12. Install retaining ring (64) in stator (63) .
Illustration 10 g03542936
13. Raise the temperature of stator (63) .
14. Install stator (63) onto carrier assembly (61) .
5/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g03542917
15. Install snap ring (62) .
Illustration 12 g03542898
16. Install the stator and carrier assembly (61) as a unit to rotating housing (54) .
Illustration 13 g03542876
17. Install thrust bearing race (60), thrust bearing (59), and thrust bearing race (58) .
6/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g03542819
21. Install bolts (55) to drive flange (53). Tighten bolts (55) to a torque of 80 ± 10 N·m (59 ± 7
lb ft).
Illustration 17 g03542001
22. Use two people in order to install drive flange (53) on rotating housing (54). The weight of
drive flange (53) is approximately 23 kg (51 lb).
23. Install bolts (52) and the washers. Tighten bolts (52) to a torque of 30 ± 5 N·m (22 ± 4 lb ft).
Illustration 18 g03545936
24. Lower the temperature of outer bearing race (51) .
25. Install outer bearing race (51) into drive gear (50).
8/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 19 g03541957
26. Install drive gear (50). Install bolts (49) and the washers. Tighten bolts (49) to a torque of 50
± 7 N·m (37 ± 5 lb ft).
Illustration 20 g03546276
27. Raise the temperature of inner bearing (48) .
28. Install inner bearing (48) onto bearing carrier (42) .
9/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g03541898
29. Install retaining ring (47) onto bearing carrier (42) .
Illustration 22 g03546297
30. Raise the temperature of ring carrier (46) .
31. Install ring carrier (46) onto bearing carrier (42) .
Illustration 23 g03541664
32. Install seal ring (45) onto ring carrier (46) .
33. Install O-ring seal (44) on bearing carrier (42)
10/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 36. Install retaining ring (38) into the groove of idler gear (28) .
Illustration 27 g03546416
37. Lower the temperature of bearing cup (39) .
38. Install bearing cup (39) into idler gear (28) .
Illustration 28 g03541116
39. Flip idler gear (28) to the opposite side. Install bearing cup spacer (37) in idler gear (28).
The notch in bearing cup spacer (37) must be aligned with the retaining ring.
12/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 29 g03546456
40. Lower the temperature of bearing cup (36) .
41. Install bearing cup (36) into idler gear (28) .
Illustration 30 g03540968
42. Install bearing cone (35) , bearing cone spacer (34), and bearing cone (33) in idler gear
(28) .
13/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 31 g03540776
43. Install O-ring seal (32) and ball (31) to shaft assembly (29) .
Illustration 32 g03546532
44. Install O-ring seal (30) to torque converter cover (3) .
45. Install idler gear (28) and shaft assembly (29) (not show) to torque converter cover (3) .
46. Install bolt (27) and the washer. Tighten bolt (27) to a torque of 120 ± 20 N·m (89 ± 15 lb
ft).
Illustration 33 g03541363
Improper assembly of parts that are spring loaded can cause bodily
injury.
14/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
47. Install poppet (23), spring (24), retainer (25), retaining ring (26), and spacers (22) into spool
(21) .
Illustration 34 g03541319
48. Install spool (21) and spring (20) into relief valve assembly (16) .
Illustration 35 g03541281
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
15/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 49. Install the O-ring seal, cover (18), and the bolts. Repeat this step for the opposite side.
50. Install the O-ring seal and fitting (19) .
Illustration 36 g03541236
51. Install O-ring seals (17) to relief valve assembly (16) .
Illustration 37 g03541198
52. Position relief valve (16) to torque converter cover (3). Install bolts (15) and the washers.
16/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 38 g03540719
53. Lower the temperature of bearing cup (14) .
54. Install bearing cup (14) to torque converter cover (3) .
Illustration 39 g03546602
55. Raise the temperature of bearing cone (13) .
56. Install bearing cone (13) to pump drive gear (12) .
17/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 40 g03540096
57. Install pump drive gear (12) into torque converter cover (3) .
Illustration 41 g03540077
58. Lower the temperature of bearing cup (9) .
59. Install bearing cup (9) to pump adapter (8) .
60. Install shims (10) to pump adapter (8) .
61. Apply clean hydraulic oil to O-ring seal (11). Install O-ring seal (9) .
Illustration 42 g03546659
62. Install Tooling (D) to torque converter cover (3). Use Tooling (D) in order to guide pump
adapter (8) into position on torque converter cover (3) .
18/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 43 g03546663
63. Install bolts (7) and the washers.
64. Use Tooling (B) in order to check bearing end play. The bearing end play must be 0.15 ±
0.05 mm (0.006 ± 0.002 inch). Add or remove shims in order to get the correct bearing end
play.
Note: If end play is less than 0.10 mm (0.004 inch), add additional shims. If end play is
greater than 0.20 mm (0.008 inch), remove shims.
Illustration 44 g03548097
65. Install the O-ring seal, adapter (6), the washers, and the bolts.
19/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 45 g03539953
66. Install elbow (5). Install O-ring seal (4) .
Illustration 46 g03547436
67. Install Tooling (E) .
68. Attach Tooling (A) and a suitable lifting device to torque converter cover (3). The weight of
torque converter cover (3) is approximately 120 kg (265 lb). Use Tooling (A) and the
suitable lifting device in order to install torque converter cover (3) on the torque converter.
20/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 47 g03539596
69. Install bolts (2) and the washers. Tighten bolts (2) to a torque of 120 ± 20 N·m (89 ± 15 lb
ft). Install output shaft (1) .
End By: Connect the torque converter to the transmission and the output gears.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Mar 20 17:22:08 UTC+0800 2021
21/21
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEB...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980H WHEEL LOADER PF8
Configuration: 980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
980H Wheel Loader
Power Train
Media Number -UENR3319-00 Publication Date -01/02/2014 Date Updated -04/02/2014
i02187020
Transmission from Output Transfer Gears - Separate
SMCS - 3002-076
Separation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 138-7575 Link Bracket 1
C 138-7575 Link Bracket 3
Start By:
a. Separate the torque converter from the transmission. Refer to Disassembly and Assembly,
"Torque Converter from Transmission, Output Transfer Gears - Separate".
1/4
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g01105945
Illustration 2 g01105953
1. Use Tooling (A), Tooling (B) and a suitable lifting device in order to reposition the
transmission and output transfer gears (1) onto suitable cribbing. The weight of the
transmission and output transfer gears (1) is approximately 1406 kg (3100 lb).
Illustration 3 g01105947
2/4
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 6 g01105978
5. Attach Tooling (C) and a suitable lifting device to transmission (6). The weight of
transmission (6) is approximately 726 kg (1600 lb). Remove bolts (7). Do not remove the
two smaller bolts (8).
Illustration 7 g01105986
6. Use the suitable lifting device in order to remove transmission (6).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Mar 20 17:23:05 UTC+0800 2021
4/4
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 980H WHEEL LOADER PF8
Configuration: 980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine
Disassembly and Assembly
980H Wheel Loader
Power Train
Media Number -UENR3319-00 Publication Date -01/02/2014 Date Updated -04/02/2014
i05593710
Output Transfer Gears - Disassemble
SMCS - 3075-015-OJ
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
B
8B-7548 Push-Puller Tool Gp 1
8B-7551 Bearing Puller Gp 1
9S-9154 Step Plate 1
C 439-3940 Bracket As 2
D -
Forcing Bolt
3/8 - 16 by 6 in
2
Start By:
A. Remove the transmission from the output transfer gears.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/17
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 3 g01108605
3. Remove bolt (3) and retainer (4) from the input side of the output transfer gear case.
Illustration 4 g01108617
4. Remove O-ring seal (5) .
Illustration 5 g01108628
5. Remove yoke (6) .
3/17
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
31. Illustration 6 g01108630
6. Remove bolts (7) and the washers from bearing cage (8) .
Illustration 7 g01108631
7. Use Tooling (D) in order to remove bearing cage (8) .
Illustration 8 g01108635
4/17
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. 8. Use Tooling (A) in order to remove lip seal (9) and outer bearing race (10) from bearing
cage (8) .
Illustration 9 g01108639
9. Remove O-ring seal (11) from bearing cage (8) .
Illustration 10 g01108665
10. Remove spacer (12) from transfer shaft (13) .
5/17
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Illustration 11 g01108680
11. Position the transfer case with the output side upward, as shown. The weight of the output
transfer gear group is 526 kg (1160 lb).
12. Mark bolts (14) for installation purposes. Remove bolts (14) and the washers from bearing
cage (15) .
13. Use Tooling (D) in order to loosen bearing cage (15) from the transfer case. Remove
bearing cage (15) .
Illustration 12 g01108700
14. Position bearing cage (15) onto a suitable press. The combined weight of bearing cage (15)
and transfer shaft (13) is approximately 61 kg (135 lb). Use the suitable press in order to
press transfer shaft (13) out of bearing cage (15) .
Note: Place a suitable block (not shown) under transfer shaft (13) in order to prevent
transfer shaft (13) from falling to the ground.
6/17
980H Wheel Loader PF800001-UP (MACHINE) POWERED BY C15 Engine(SEBP6...
2021/3/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...