1. Product: TRACK-TYPE TRACTOR
Model: D6M TRACK-TYPE TRACTOR 5WR
Configuration: D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
D6M Track-Type Tractor Power Train
Media Number -SENR9482-04 Publication Date -01/01/2011 Date Updated -31/01/2011
i04026193
Final Drive - Assemble
SMCS - 4170-077
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
E 1P-0520 Driver Gp 1
F
1U-6436
or
1U-6437
Duo-Cone Seal Installer As 1
G 138-7575 Link Bracket 2
H 8T-3225 Spacer 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/7
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. Illustration 1 g02211113
1. Use Tooling (E) to install seal (19) in the spindle. Install the seal with the lip upward, as
shown.
2. If bearing cone (21) was removed, raise the temperature of the bearing cone to a maximum
temperature of 120°C (248°F), and install the bearing cone on the spindle.
3. Use Tooling (F) to install Duo-Cone seal (20) on the hub.
Illustration 2 g02210855
4. If bearing cups (18) were removed from the hub, lower the temperature of the bearing cups.
Install bearing cups (18) in the hub.
5. Use Tooling (F) to install Duo-Cone seal (17) in the hub.
2/7
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 3 g02211137
6. Attach a suitable lifting device and Tooling (G) to hub (15) . The weight of the hub is
approximately 159 kg (350 lb). Lower hub (15) in position on spindle (16) .
Illustration 4 g02211139
7. Raise the temperature of bearing cone (14) to a maximum temperature of 120°C (248°F).
Install bearing cone (14) on the spindle.
Illustration 5 g02211153
3/7
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Note: If Tooling (H) is not available or does not fit the spindle, skip to Step 10. Use hub
(12) to press bearing cone (14) into position. Press hub (12) until the surface of hub (12) is
even with the surface on the spindle.
8. While bearing cone (14) is still hot, place Tooling (H) in position. Install retainer (10) and
bolts (9) . Tighten bolts (9) to a torque of 135 N·m ± 15 N·m (100 lb ft ± 11 lb ft).
9. After bearing cone (14) has cooled, remove the retainer and Tooling (H) .
Illustration 6 g02211154
10. Put hub (12) in position in gear (11) . Install ring (13) .
Illustration 7 g02210775
11. Attach a suitable lifting device to hub (12) . Put hub (12) and gear (11) in position on the
spindle as an assembly. The weight of the gear and the hub is approximately 34 kg (75 lb).
4/7
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 8 g02211196
12. Install retainer (10) and bolts (9) . Tighten bolts (9) to a torque of 135 N·m ± 15 N·m (100
lb ft ± 11 lb ft).
13. Use a feeler gauge to verify that there is metal to metal contact between retainer (10) and the
spindle.
Illustration 9 g00710936
Illustration 10 g02211234
5/7
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 14. If bearing cups (6) were removed from gear (7) , lower the temperature of bearing cups (6) .
Install bearing cups (6) in gear (7) .
15. Put bearing cones (8) and (5) in position in gear (7) .
16. Put the bearing cones and gear (7) in position in carrier (1) . Lower the temperature of shaft
(4) . Use a suitable press to install shaft (4) in carrier (1) . Install shaft (4) until the end of
shaft (4) is even with the outside surface of carrier (1) .
Illustration 11 g00710931
17. Install retainers (3) and bolts (2) . There must be a metal to metal contact between retainers
(3) and the shafts.
Illustration 12 g02211253
18. Attach a suitable lifting device and Tooling (A) to carrier (1) . The weight of the carrier is
approximately 98 kg (215 lb). Put carrier (1) in position in hub (15) . Install bolts (22) .
End By: Install the final drives. Refer to Disassembly and Assembly, "Final Drive - Install".
6/7
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Product: TRACK-TYPE TRACTOR
Model: D6M TRACK-TYPE TRACTOR 5WR
Configuration: D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
D6M Track-Type Tractor Power Train
Media Number -SENR9482-04 Publication Date -01/01/2011 Date Updated -31/01/2011
i00964538
Final Drive - Install
SMCS - 4170-077
Installation Procedure
Table 1
Tools Needed A
8T-3207 Lifting Bracket 1
5P-8622 Shackle 1
1D-4612 Bolt 3/4 inch - 10 NC x 4 inch (102 mm) 2
9S-9076 Spacer 2
Illustration 1 g00710570
1. Put O-ring (8) in position on the steering clutch and the brake housing.
1/3
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 2 g00710573
Illustration 3 g00710577
2. Fasten a hoist and Tooling (A) to final drive (4) .
3. Put the final drive in position on the steering clutch and the brake housing. Install bolts (6)
and (7) .
4. Remove Tooling (A) from the final drive.
2/3
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 4 g00710590
5. Install two bolts (1) .
6. Install drain plug (2) .
7. Fill the final drive with oil to the correct level.
End By:
a. Install the axles. Refer to Disassembly and Assembly, "Axle - Remove and Install".
b. Connect the tracks. Refer to Disassembly and Assembly, "Track - Connect".
3/3
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Product: TRACK-TYPE TRACTOR
Model: D6M TRACK-TYPE TRACTOR 5WR
Configuration: D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
D6M Track-Type Tractor Power Train
Media Number -SENR9482-04 Publication Date -01/01/2011 Date Updated -31/01/2011
i00965393
Steering Clutch and Brake - Remove
SMCS - 4170-077
Removal Procedure
Table 1
Tools Needed A
8T-3207 Lifting Bracket 1
5P-8622 Shackle 1
1D-4612 Bolt 3/4 inch - 10 NC x 4 inch (102 mm) 2
9S-9076 Spacer 2
Start By:
A. Separate the tracks. Refer to Disassembly and Assembly, "Track - Separate".
B. Remove the axles. Refer to Disassembly and Assembly, "Axle - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/4
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 1. Drain the oil from the transmission and the bevel gear housing.
Illustration 1 g00712231
2. Turn the final drive until plug (2) is on the bottom. Drain the oil from the final drive
housing.
3. Remove bolts (1) from the top of the final drive.
Illustration 2 g00712534
4. Adjust bracket (3) until the bracket is against the stop on Tooling (A) .
2/4
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00712228
Illustration 4 g00712226
5. Fasten a hoist and Tooling (A) to final drive (4), as shown.
Note: Do not remove bolts (6) that hold the steering clutch and brake to the final drive.
6. Remove bolts (5) and (7). Remove the final drive and the steering clutch as an assembly.
The weight of the final drive, steering clutch, and brake assembly is 544 kg (1200.0 lb).
Illustration 5 g00712224
3/4
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 7. Remove O-ring seals (8) and (9) from the steering clutch and the brake housing.
4/4
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Product: TRACK-TYPE TRACTOR
Model: D6M TRACK-TYPE TRACTOR 5WR
Configuration: D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
D6M Track-Type Tractor Power Train
Media Number -SENR9482-04 Publication Date -01/01/2011 Date Updated -31/01/2011
i00963261
Steering Clutch and Brake - Disassemble
SMCS - 4170-077
Disassembly Procedure
Table 1
Tools Needed A
6V-2156 Link Bracket 2
Start By:
A. Separate the final drive, the steering clutches, and the brakes. Refer to Disassembly and
Assembly, "Final Drive, Steering Clutch, and Brakes - Separate".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g00687366
1/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 1. Remove bolts (1) and plate (2) .
Illustration 2 g00687369
2. Remove housing (3) .
Illustration 3 g00687373
3. Remove six plates (4) and the five discs from hub (5) .
2/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g00687377
4. Remove two plugs (6) from hub (5) .
5. Remove the six bolts that hold hub (5) in place through the plug holes. Remove the hub.
Illustration 5 g00687384
6. Remove ring (7) from hub (5). Remove bearing (9) and retainer (8) from the hub as an
assembly.
Illustration 6 g00687388
7. Remove retainer (8) from bearing (9) .
3/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 7 g00687392
8. Remove piston (10). Remove seals (11) and (12) from the piston.
Illustration 8 g00687398
9. Remove ring (14) from hub assembly (13) .
4/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 9 g00687400
10. Fasten a hoist and Tool (A) to housing (15). Remove the brake assembly from hub assembly
(13). The weight of the brake assembly is 86 kg (190.0 lb).
Illustration 10 g00687407
11. Remove bearing (17) and race (16) from housing (15) .
5/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 11 g00687408
12. Remove three rings (18) from hub assembly (13) .
13. If necessary, remove bearing (19) from the hub assembly.
Illustration 12 g00687409
Personal injury can result from parts under high spring pressure.
Spring force can cause parts to come off suddenly. Contact your
Caterpillar dealer for disassembly instructions before removing any
parts.
Note: Bolts (22) hold a spring under compression behind the piston. Bolts (20) must be
removed before bolts (22) .
14. Remove bolts (20) and plate (21) from housing (15) .
6/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 13 g00687823
15. Remove spring (25) and ring (24) from housing (15) .
16. Remove four plates (26) and three discs (23) from the housing.
Illustration 14 g00687827
Personal injury can result from parts under high spring pressure.
Spring force can cause parts to come off suddenly. Contact your
Caterpillar dealer for disassembly instructions before removing any
parts.
Note: Bolts (22) hold a spring under compression. Loosen the bolts slowly and loosen the
bolts evenly.
17. Remove six bolts (22) and manifold assembly (27) from housing (15) .
7/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 15 g00687840
18. Remove seals (29) and (30) from manifold assembly (27) .
19. If necessary, remove bearing race (28) from the manifold assembly.
Illustration 16 g00687841
20. Remove piston (31) from the housing.
21. Remove O-ring seal (32) .
8/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 17 g00687843
22. Remove two springs (33) from housing (15) .
9/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Product: TRACK-TYPE TRACTOR
Model: D6M TRACK-TYPE TRACTOR 5WR
Configuration: D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
D6M Track-Type Tractor Power Train
Media Number -SENR9482-04 Publication Date -01/01/2011 Date Updated -31/01/2011
i03743864
Steering Clutch and Brake - Assemble
SMCS - 4170-077
Assembly Procedure
Table 1
Tools Needed A B
5P-9736 Link Bracket 3
1P-0510 Driver Group 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1. Replace all parts that are damaged or worn.
Illustration 1 g00686742
1/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 2. Install two springs (1) in housing (2) . Install the two springs so that the concave sides face
each other.
Illustration 2 g00686749
3. Put piston (3) in position in housing (2) .
4. Install O-ring seal (4) in housing (2) .
Illustration 3 g00686760
5. If race (6) was removed from manifold assembly (5) , lower the temperature of race (6) ,
and install race (6) in manifold assembly (5) .
6. Install seals (7) and (8) on manifold assembly (5) . Install the seals on the manifold
assembly with the lip of the seals, as shown. Put clean oil on the lip of the seals.
2/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 4 g00686784
7. Align the oil holes in manifold assembly (5) with the holes in housing (2) . Install the
manifold assembly and six bolts (9) .
Illustration 5 g00681377
This is the correct method for making new seal rings ready for installation.
Illustration 6 g00681389
3/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. This is the wrong method for making new seal rings ready for installation.
NOTICE
New seal rings must be preloaded before they are installed to prevent
them from being damaged or broken. There is a correct method to
preload new seal rings prior to installation. Place your hands on each
end of the seal ring, and pull (wind) the ends several inches past each
other or until they almost make contact. Use care to keep the ring
shaped like a circle. This will make an even bend (or ring "set") all
around the ring. When the seal ring is in the groove of the hub, the
ends must butt together lightly. Do not bend the seal ring. This does
not make an even bend all the way around the ring.
Do not attempt to use this method to preload a used seal ring. Also, do
not use this procedure for cast iron seal rings. This will cause used or
cast iron seal rings to break.
Illustration 7 g00686824
8. If bearing (12) was removed, heat the bearing to a maximum temperature of 120°C (248.0°
F) for a maximum of eight hours. Install the bearing on hub assembly (10) . The bearing
must be seated squarely on the hub assembly after the bearing has cooled.
9. Install three rings (11) on hub assembly (10) .
4/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 8 g00686855
10. Lower the temperature of race (13) . Install the race in housing (2) .
11. Fasten a hoist and Tooling (A) to housing (2) . Lower the housing in position on hub
assembly (10) .
Illustration 9 g00686860
12. Heat bearing (14) to a maximum temperature of 120°C (248.0°F) for a maximum of eight
hours. Install the bearing on hub assembly (10) . Make sure that the bearing is seated
squarely on the hub assembly after the bearing has cooled.
13. Install ring (15) on the hub assembly.
5/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
29. Illustration 10 g01991753
14. Install spring (16) with the concave side facing ring (17) . Install ring (17) .
15. Start with a plate and install four plates (18) and the three discs. Alternate the plates and the
discs.
Illustration 11 g00686869
16. Install plate (20) and bolts (19) on housing (2) .
6/9
D6M Track-Type Tractor Power Shift 5WR00001-UP (MACHINE) POWERED BY 3...
2021/12/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...