1. The document provides instructions for disassembling and assembling the final drive of a D6M Track-Type Tractor. It details removing and installing various components like carriers, gears, seals, and bearings.
2. Cleaning procedures and replacement of O-rings are emphasized to prevent contamination. Special tools are listed to facilitate removal and installation of components.
3. The assembly procedure mirrors the disassembly steps and provides torque specifications for fasteners. Filling the final drive with the proper oil is the last step before reinstalling removed components.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. The disassembly procedure involves using various tools to remove 19 components of the final drive including the planetary carrier, gears, seals, and hub. The assembly procedure describes installing these 19 components in reverse order and adjusting tools as needed. Precautions are provided such as cleaning parts and controlling temperatures during installation.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. The disassembly procedure involves using various tools to remove 19 components of the final drive including the planetary carrier, gears, seals, and hub. The assembly procedure describes installing these 19 components in reverse order and adjusting tools as needed. Precautions are provided such as cleaning parts and controlling temperatures during installation.
This document provides instructions for disassembling and assembling the final drive of a Caterpillar D6T track-type tractor. The disassembly procedure involves using various tools to remove 19 components of the final drive including the planetary carrier, gears, seals, and hub. The assembly procedure provides reverse instructions and specifies cleaning and heating components, applying oil, and torquing bolts to the correct specifications. Proper installation of seals and shafts is emphasized to ensure correct bearing preload.
This document provides instructions for disassembling and assembling the final drive, steering differential, and brake on the left side of a D6T track-type tractor. Key steps include using specialized tools to remove the adapter, sliding carrier, and final drive/differential assembly. The assembly procedure involves installing components in reverse order and adjusting bearing temperatures during installation.
This document provides instructions for disassembling and assembling the final drive, steering differential, and brake on the left side of a D6T track-type tractor. Key steps include using specialized tools to remove the adapter, sliding carrier, and final drive/differential assembly. The assembly procedure involves installing components in reverse order and adjusting bearing temperatures during installation.
This document provides instructions for disassembling and assembling the final drive, steering differential, and brake on the left side of a D6T track-type tractor. Key steps include using specialized tools to remove the adapter, sliding carrier, and final drive/differential assembly. The assembly procedure involves installing components in reverse order and adjusting bearing temperatures during installation.
The document provides instructions for removing the final drive, steering differential, and brake from the left side of a D6N track-type tractor. It lists the required tools and presents a 20-step procedure involving removing mounting bolts, shafts, gears, seals, and other components. Detailed illustrations accompany each step to show the correct positioning of tools and order of disassembly.
The document provides instructions for removing the final drive, steering differential, and brake from the left side of a D6N track-type tractor. It lists the required tools and presents a 20-step procedure involving removing mounting bolts, shafts, gears, seals, and other components. Detailed illustrations accompany each step to show the correct positioning of tools and order of disassembly.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. The disassembly procedure involves using various tools to remove 19 components of the final drive including the planetary carrier, gears, seals, and hub. The assembly procedure describes installing these 19 components in reverse order and adjusting tools as needed. Precautions are provided such as cleaning parts and controlling temperatures during installation.
The document provides instructions for disassembling and assembling the final drive of a D6T track-type tractor. The disassembly procedure involves using various tools to remove 19 components of the final drive including the planetary carrier, gears, seals, and hub. The assembly procedure describes installing these 19 components in reverse order and adjusting tools as needed. Precautions are provided such as cleaning parts and controlling temperatures during installation.
This document provides instructions for disassembling and assembling the final drive of a Caterpillar D6T track-type tractor. The disassembly procedure involves using various tools to remove 19 components of the final drive including the planetary carrier, gears, seals, and hub. The assembly procedure provides reverse instructions and specifies cleaning and heating components, applying oil, and torquing bolts to the correct specifications. Proper installation of seals and shafts is emphasized to ensure correct bearing preload.
This document provides instructions for disassembling and assembling the final drive, steering differential, and brake on the left side of a D6T track-type tractor. Key steps include using specialized tools to remove the adapter, sliding carrier, and final drive/differential assembly. The assembly procedure involves installing components in reverse order and adjusting bearing temperatures during installation.
This document provides instructions for disassembling and assembling the final drive, steering differential, and brake on the left side of a D6T track-type tractor. Key steps include using specialized tools to remove the adapter, sliding carrier, and final drive/differential assembly. The assembly procedure involves installing components in reverse order and adjusting bearing temperatures during installation.
This document provides instructions for disassembling and assembling the final drive, steering differential, and brake on the left side of a D6T track-type tractor. Key steps include using specialized tools to remove the adapter, sliding carrier, and final drive/differential assembly. The assembly procedure involves installing components in reverse order and adjusting bearing temperatures during installation.
The document provides instructions for removing the final drive, steering differential, and brake from the left side of a D6N track-type tractor. It lists the required tools and presents a 20-step procedure involving removing mounting bolts, shafts, gears, seals, and other components. Detailed illustrations accompany each step to show the correct positioning of tools and order of disassembly.
The document provides instructions for removing the final drive, steering differential, and brake from the left side of a D6N track-type tractor. It lists the required tools and presents a 20-step procedure involving removing mounting bolts, shafts, gears, seals, and other components. Detailed illustrations accompany each step to show the correct positioning of tools and order of disassembly.
Massey Ferguson MF 384 S TRACTOR (- 300993) Parts Catalogue Manual Instant Do...onyvzcwadtu05
This document contains parts listings and technical specifications for the engine of a Massey Ferguson 384 S tractor. It includes 6 pages detailing over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, cylinder head, rocker shaft, and air induction and exhaust systems. Each part is listed with its part number, quantity, description, and any relevant comments.
Massey Ferguson MF 384 F TRACTOR, - 0894 Parts Catalogue Manual Instant Downl...onyvzcwadtu05
The document is a parts catalog for a Massey Ferguson MF 384 F tractor engine. It lists over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft and other components. Each part is given a reference number, part number, quantity and description, along with any replacement or additional part information.
The document suggests that if clicking the above button is invalid, the user should first download the document and then click the link to download the complete manual. It thanks the reader for their time.
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and housing pieces. It then lists 36 steps for assembly, installing components in reverse order and noting proper orientation of marked parts. Precautions are provided regarding contained fluids, released spring forces, and keeping parts clean from contaminants. Required specialty tools are also listed.
This document provides instructions for assembling the main hydraulic pump on an excavator model. It lists the required tools and parts. It then provides 49 steps with accompanying illustrations, describing how to install each component of the pump in detail, including bearings, seals, pistons, springs, and valves. The final step instructs the technician to install the assembled pump.
The document provides instructions for installing a swing drive on an excavator model M315D. It lists the required tools and parts. The procedure involves 28 steps, including installing bearings, seals, gears, and other components into the swing drive housing. Specific torque specifications and dimensional checks are listed to ensure proper assembly. Installation is completed by positioning the swing drive in the swing brake housing and securing it with bolts.
This document provides instructions for removing and installing a pilot control valve on a D10 track-type tractor. Key steps include removing the right side console cover, disconnecting control rods from the valve spools using pins and cotter pins, labeling and disconnecting all oil lines, and removing bolts to take off the pilot control valve. Reinstallation involves installing the pilot control valve on the bracket with bolts, connecting the labeled oil lines, and attaching the control rods to the valve spools with pins and cotter pins.
This document provides instructions for disassembling and assembling the final drive of a D9R track-type tractor. It describes removing components such as the planetary carrier, gears, shafts, and hub. Various tools are required, including link brackets, a push-puller tool group, driver group, and hydraulic cylinder assembly. Precautions are given for using hydraulic cylinders and puller studs during disassembly. The multi-step process includes pressing, lifting, and removing components from the planetary carrier, sun gear, and hub.
This document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor. It describes:
1) Removing over 30 components of the final drive including gears, shafts, bearings, seals and hubs using various tools.
2) Inspecting all parts and replacing any that are damaged.
3) Heating some bearings cones to aid removal and ensuring proper temperatures when installing.
4) Precisely assembling the components in reverse order, taking care with sealing surfaces.
1) The document provides instructions for removing and installing the final drive planetary carrier in a D9R track-type tractor.
2) It describes using various tools to remove the carrier, hub components, seals, and gears. It then explains how to clean and prepare the parts for installation and use the tools to reinstall the components in reverse order.
3) Fourteen steps are outlined to remove the carrier and twelve steps are provided to install it back into the final drive assembly.
The document provides instructions for disassembling and assembling the steering clutch and brake of a Caterpillar D7R track-type tractor. It details 20 steps to disassemble the components which include removing bolts, plates, bearings, seals and other parts. The 20 steps to assemble are also outlined and include cleaning parts, applying oil, heating bearings, and reinstalling components in reverse order. Special safety precautions are noted regarding spring loaded components.
The document provides assembly instructions for installing a final drive on a D7R track-type tractor. It describes 31 steps to assemble bearings, seals, gears, shafts, covers and other components. Tools required include drivers, seal installers, brackets and spacers. Precise torques and clearances are specified. The assembly is completed by filling the final drive with oil and reconnecting the track.
Caterpillar Cat D7R II WATER FORDING TRACTOR (Prefix DJT) Service Repair Manu...onyvzcwadtu05
This document provides instructions for disassembling and assembling the steering planetary and brake of a D7R Series II Water Fording Tractor. It describes removing 24 components including the planetary group, brake, ring gear, friction discs, piston, and springs. Reassembly involves installing these components in reverse order, noting proper orientation and torque specifications. Tools required include link brackets, a driver group, forcing bolts, and sealant.
Caterpillar Cat D7R II TRACK-TYPE TRACTOR (Prefix AGN) Service Repair Manual ...onyvzcwadtu05
The document provides instructions for removing a final drive, steering planetary, and brake assembly from a D7R II track-type tractor. It describes using lifting brackets, shackles, bolts and nuts to attach a hoist to the assembly and remove it from the tractor. The assembly weighs approximately 800 kg (1750 lb) and precautions are listed to provide means to stop the machine without the brake installed. Fluids must be contained while working on components to collect any fluids that may drain out.
This document provides instructions for disassembling and assembling the final drives on a D7H track-type tractor. The main steps for disassembly are to remove the final drives from the machine, then disassemble the internal components which include removing planet carriers, gears, shafts, and bearings. For assembly, the components are installed in reverse order, with specifics on cleaning, heating/cooling parts, and using installation tools to properly set clearances and ensure metal-to-metal contact between parts.
This document provides instructions for servicing the final drives on a D7H track-type tractor. It describes how to remove and disassemble the final drives, including removing the planet carriers, gears, shafts and other components. It then describes how to assemble the final drives, including installing bearings, seals, rings and other parts back into the hubs and carriers. The goal is to provide maintenance technicians with step-by-step directions for servicing these critical components.
1) The document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and crankshaft main bearings for a Caterpillar 3306 engine.
2) The procedure involves using tools to compress piston rings, installing pistons and connecting rods onto the crankshaft, checking clearances of connecting rod bearings, and removing/installing main bearing caps.
3) Technicians are advised to keep all parts clean and lubricated with engine oil to prevent damage and wear.
The document provides instructions for removing and installing sprocket assemblies on a track-type tractor. It involves 22 steps to remove the assemblies, which includes draining oil, removing seals, bearings, and other components. The 23 steps to install include pressing in new seals, bearings, and sprockets using specialized tools and applying precise forces, and adjusting bearings after reinstalling track roller frames. Proper cleaning, lubrication and torque specifications are noted throughout.
The document provides step-by-step instructions for removing and installing sprocket assemblies on a final drive case. It involves draining oil, removing the sprocket and various components using specialized tools, cleaning surfaces, replacing seals, installing new components in reverse order, and filling with oil. Proper alignment and torque specifications are noted throughout.
The document provides instructions for removing and installing final drive case assemblies on a D7G track-type tractor. It describes draining oil from the final drive case and removing components like caps, locks, nuts, seals and bearings. It explains using tools and hoists to separate the sprocket, holder assembly and adjusting nut as a unit from the tapered sprocket shaft. Finally, it outlines reinstalling the sprocket assembly and adjusting the bearings.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Massey Ferguson MF 384 S TRACTOR (- 300993) Parts Catalogue Manual Instant Do...onyvzcwadtu05
This document contains parts listings and technical specifications for the engine of a Massey Ferguson 384 S tractor. It includes 6 pages detailing over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, cylinder head, rocker shaft, and air induction and exhaust systems. Each part is listed with its part number, quantity, description, and any relevant comments.
Massey Ferguson MF 384 F TRACTOR, - 0894 Parts Catalogue Manual Instant Downl...onyvzcwadtu05
The document is a parts catalog for a Massey Ferguson MF 384 F tractor engine. It lists over 60 individual parts for the engine, including the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft and other components. Each part is given a reference number, part number, quantity and description, along with any replacement or additional part information.
The document suggests that if clicking the above button is invalid, the user should first download the document and then click the link to download the complete manual. It thanks the reader for their time.
This document provides instructions for disassembling and assembling the main hydraulic pump on a M315D Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and housing pieces. It then lists 36 steps for assembly, installing components in reverse order and noting proper orientation of marked parts. Precautions are provided regarding contained fluids, released spring forces, and keeping parts clean from contaminants. Required specialty tools are also listed.
This document provides instructions for assembling the main hydraulic pump on an excavator model. It lists the required tools and parts. It then provides 49 steps with accompanying illustrations, describing how to install each component of the pump in detail, including bearings, seals, pistons, springs, and valves. The final step instructs the technician to install the assembled pump.
The document provides instructions for installing a swing drive on an excavator model M315D. It lists the required tools and parts. The procedure involves 28 steps, including installing bearings, seals, gears, and other components into the swing drive housing. Specific torque specifications and dimensional checks are listed to ensure proper assembly. Installation is completed by positioning the swing drive in the swing brake housing and securing it with bolts.
This document provides instructions for removing and installing a pilot control valve on a D10 track-type tractor. Key steps include removing the right side console cover, disconnecting control rods from the valve spools using pins and cotter pins, labeling and disconnecting all oil lines, and removing bolts to take off the pilot control valve. Reinstallation involves installing the pilot control valve on the bracket with bolts, connecting the labeled oil lines, and attaching the control rods to the valve spools with pins and cotter pins.
This document provides instructions for disassembling and assembling the final drive of a D9R track-type tractor. It describes removing components such as the planetary carrier, gears, shafts, and hub. Various tools are required, including link brackets, a push-puller tool group, driver group, and hydraulic cylinder assembly. Precautions are given for using hydraulic cylinders and puller studs during disassembly. The multi-step process includes pressing, lifting, and removing components from the planetary carrier, sun gear, and hub.
This document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor. It describes:
1) Removing over 30 components of the final drive including gears, shafts, bearings, seals and hubs using various tools.
2) Inspecting all parts and replacing any that are damaged.
3) Heating some bearings cones to aid removal and ensuring proper temperatures when installing.
4) Precisely assembling the components in reverse order, taking care with sealing surfaces.
1) The document provides instructions for removing and installing the final drive planetary carrier in a D9R track-type tractor.
2) It describes using various tools to remove the carrier, hub components, seals, and gears. It then explains how to clean and prepare the parts for installation and use the tools to reinstall the components in reverse order.
3) Fourteen steps are outlined to remove the carrier and twelve steps are provided to install it back into the final drive assembly.
The document provides instructions for disassembling and assembling the steering clutch and brake of a Caterpillar D7R track-type tractor. It details 20 steps to disassemble the components which include removing bolts, plates, bearings, seals and other parts. The 20 steps to assemble are also outlined and include cleaning parts, applying oil, heating bearings, and reinstalling components in reverse order. Special safety precautions are noted regarding spring loaded components.
The document provides assembly instructions for installing a final drive on a D7R track-type tractor. It describes 31 steps to assemble bearings, seals, gears, shafts, covers and other components. Tools required include drivers, seal installers, brackets and spacers. Precise torques and clearances are specified. The assembly is completed by filling the final drive with oil and reconnecting the track.
Caterpillar Cat D7R II WATER FORDING TRACTOR (Prefix DJT) Service Repair Manu...onyvzcwadtu05
This document provides instructions for disassembling and assembling the steering planetary and brake of a D7R Series II Water Fording Tractor. It describes removing 24 components including the planetary group, brake, ring gear, friction discs, piston, and springs. Reassembly involves installing these components in reverse order, noting proper orientation and torque specifications. Tools required include link brackets, a driver group, forcing bolts, and sealant.
Caterpillar Cat D7R II TRACK-TYPE TRACTOR (Prefix AGN) Service Repair Manual ...onyvzcwadtu05
The document provides instructions for removing a final drive, steering planetary, and brake assembly from a D7R II track-type tractor. It describes using lifting brackets, shackles, bolts and nuts to attach a hoist to the assembly and remove it from the tractor. The assembly weighs approximately 800 kg (1750 lb) and precautions are listed to provide means to stop the machine without the brake installed. Fluids must be contained while working on components to collect any fluids that may drain out.
This document provides instructions for disassembling and assembling the final drives on a D7H track-type tractor. The main steps for disassembly are to remove the final drives from the machine, then disassemble the internal components which include removing planet carriers, gears, shafts, and bearings. For assembly, the components are installed in reverse order, with specifics on cleaning, heating/cooling parts, and using installation tools to properly set clearances and ensure metal-to-metal contact between parts.
This document provides instructions for servicing the final drives on a D7H track-type tractor. It describes how to remove and disassemble the final drives, including removing the planet carriers, gears, shafts and other components. It then describes how to assemble the final drives, including installing bearings, seals, rings and other parts back into the hubs and carriers. The goal is to provide maintenance technicians with step-by-step directions for servicing these critical components.
1) The document provides instructions for removing and installing pistons, connecting rods, connecting rod bearings, and crankshaft main bearings for a Caterpillar 3306 engine.
2) The procedure involves using tools to compress piston rings, installing pistons and connecting rods onto the crankshaft, checking clearances of connecting rod bearings, and removing/installing main bearing caps.
3) Technicians are advised to keep all parts clean and lubricated with engine oil to prevent damage and wear.
The document provides instructions for removing and installing sprocket assemblies on a track-type tractor. It involves 22 steps to remove the assemblies, which includes draining oil, removing seals, bearings, and other components. The 23 steps to install include pressing in new seals, bearings, and sprockets using specialized tools and applying precise forces, and adjusting bearings after reinstalling track roller frames. Proper cleaning, lubrication and torque specifications are noted throughout.
The document provides step-by-step instructions for removing and installing sprocket assemblies on a final drive case. It involves draining oil, removing the sprocket and various components using specialized tools, cleaning surfaces, replacing seals, installing new components in reverse order, and filling with oil. Proper alignment and torque specifications are noted throughout.
The document provides instructions for removing and installing final drive case assemblies on a D7G track-type tractor. It describes draining oil from the final drive case and removing components like caps, locks, nuts, seals and bearings. It explains using tools and hoists to separate the sprocket, holder assembly and adjusting nut as a unit from the tapered sprocket shaft. Finally, it outlines reinstalling the sprocket assembly and adjusting the bearings.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
1. Product: TRACK-TYPE TRACTOR
Model: D6M TRACK-TYPE TRACTOR 6LR
Configuration: D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
D6M Track-Type Tractor Power Train
Media Number -SENR8387-06 Publication Date -01/11/2010 Date Updated -31/07/2018
i04026196
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1P-0510 Driver Group 1
C
1P-0520 Driver Group 1
4C-4865 Hand Hydraulic Pump 1
FT-1934 Beam 1
6V-3160 Hydraulic Cylinder 1
5F-7353 Washer 4
- Bolt (20 mm by 200 mm) 4
D 138-7574 Link Bracket 3
Start By:
a. Remove the final drives. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will help to prevent dirt from entering
the internal mechanism. Dirt and contaminants can damage the precision components. All
Disassembly and Assembly procedures must be performed on a clean work surface. Clean
1/5
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. all the interior components in clean solvent. Dry all the interior components with
compressed air. Plug ports and plug hoses on the machine during repair.
Illustration 1 g02210755
1. Remove the bolts that hold carrier (1) to the hub.
2. Attach a suitable lifting device and Tooling (A) to carrier (1). Remove the carrier. The
weight of the carrier is approximately 98 kg (215 lb). Remove the O-ring seal from the
carrier.
Illustration 2 g00743498
3. Remove bolts (2) and retainers (3).
2/5
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 3 g00743501
Illustration 4 g00743502
4. Use a suitable press and Tooling (B) in order to push shafts (4) out of carrier (1).
5. Remove gear (7) and bearing cones (5) and (8) from the carrier.
6. If necessary, remove bearing cups (6) from gear (7).
Illustration 5 g00743503
7. Remove bolts (9) and retainer (10).
3/5
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 6 g02210775
8. Attach a suitable lifting device to hub (12). Remove the hub and gear (11) as an assembly.
The weight of the gear and the hub is approximately 34 kg (75 lb).
Illustration 7 g02210777
9. Remove ring (13) and hub (12) from gear (11).
Illustration 8 g02210778
Note: Do not lift the hub too high. The hub must not contact the fittings on the hydraulic
cylinder.
10. Install Tooling (C), as shown.
11. Raise the temperature of bearing cone (14) to a maximum temperature of 120°C (248°F).
Use Tooling (C) to remove bearing cone (14) from the spindle.
12. Remove Tooling (C) and the bearing cone.
13. Attach a suitable lifting device and Tooling (D) to hub (15). Remove the hub from spindle
(16). The weight of the hub is approximately 159 kg (350 lb).
4/5
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 9 g02210855
14. Remove Duo-Cone seal (17) from the hub.
15. If necessary, remove bearing cups (18) from the hub.
Illustration 10 g02210858
16. Remove Duo-Cone seal (20) and seal (19) from spindle (16).
17. Remove bearing cone (21) from the spindle.
5/5
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Product: TRACK-TYPE TRACTOR
Model: D6M TRACK-TYPE TRACTOR 6LR
Configuration: D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
D6M Track-Type Tractor Power Train
Media Number -SENR8387-06 Publication Date -01/11/2010 Date Updated -31/07/2018
i04026199
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 3
B 1P-0510 Driver Gp 1
D 138-7574 Link Bracket 3
E 1P-0520 Driver Gp 1
F 8T-5289 Spacer 1
G
1U-6436
or
1U-6437
Duo-Cone Seal Installer As 1
H 1U-6396 O-Ring Assembly Compound -
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly
cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be
used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect
all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other
contaminants can damage the precision components. All disassembly and all assembly
procedures must be performed on a clean work surface and in a clean area. Keep cleaned
parts covered and protected at all times.
Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring may not
have the same sealing properties as a new O-ring seal. A reconditioning procedure should
1/6
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. not be degraded because of a low-cost component such as an O-ring seal or a gasket. Use
Tooling (H) during the assembly procedure.
Illustration 1 g02213653
1. Use Tooling (E) in order to install seal (19) in spindle (16). The lip of the seal must face
upward, as shown.
Note: Make sure that the lip of seal (19) is not damaged during the installation of the axle.
2. Raise the temperature of bearing cone (21) to a maximum temperature of 120°C (248°F)
and install bearing cone (21) on spindle (16).
Note: Before installing any of the Duo-Cone seals, refer to Disassembly and Assembly,
"Duo-Cone Floating Seals - Install".
3. Use Tooling (G) in order to install the Duo-Cone seal on spindle (16).
Illustration 2 g02210855
4. Lower the temperature of bearing cups (18) and install bearing cups (18) in the hub.
5. Use Tooling (G) in order to install Duo-Cone seal (17) in the hub.
2/6
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g02213733
6. Attach Tooling (D) and a suitable lifting device to hub (15). The weight of the hub is
approximately 159 kg (350 lb). Lower hub (15) into position on spindle (16).
7. Raise the temperature of bearing cone (14) to a maximum temperature of 120°C (248°F)
and install bearing cone (14) on spindle (16).
Illustration 4 g02213813
Note: If Tooling (F) is not available or does not fit the spindle, skip to Step 10. Use hub
(12) to press bearing cone (14) into position. Press hub (12) until the surface of hub (12) is
even with the surface on the spindle.
8. While bearing cone (14) is still hot, position Tooling (F) and install retainer (10) and bolts
(9). Tighten bolts (9) to a torque of 135 ± 15 N·m (100 ± 11 lb ft).
9. After bearing cone (14) has cooled, remove retainer (10) and Tooling (F).
3/6
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 5 g02210777
10. Position hub (12) in gear (11) and install ring (13).
Illustration 6 g02210775
11. Attach a suitable lifting device to hub (12). The weight of the gear and the hub is
approximately 34 kg (75 lb). Install hub (12) and gear (11) on the spindle.
Illustration 7 g00743601
12. Install retainer (10) and bolts (9). Tighten bolts (9) to a torque of 135 ± 15 N·m
(100 ± 11 lb ft).
4/6
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 13. Use a feeler gauge in order to verify that there is metal to metal contact between retainer
(10) and the spindle.
Illustration 8 g00743602
Illustration 9 g00743604
14. If bearing cups (6) were removed from gear (7), lower the temperature of bearing cups (6)
and install bearing cups (6) in gear (7).
15. Install bearing cones (5) and (8) in gear (7).
16. Position the bearing cones and gear (7) in carrier (1). Lower the temperature of shaft (4).
Use a suitable press in order to install shaft (4) in the carrier. Install shaft (4) until the end of
shaft (4) is even with the outer surface of carrier (1).
5/6
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 10 g00743605
17. Install retainers (3) and bolts (2). There must be metal to metal contact between retainers (3)
and the shafts.
Illustration 11 g02210755
18. Position the O-ring seal on carrier (1).
19. Attach Tooling (A) and a suitable lifting device to carrier (1). The weight of the carrier is
approximately 98 kg (215 lb). Position carrier (1) on the hub assembly and install the bolts
that hold carrier (1) in place.
End By:
a. Install the final drives. Refer to Disassembly and Assembly, "Final Drive - Install".
6/6
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Product: TRACK-TYPE TRACTOR
Model: D6M TRACK-TYPE TRACTOR 6LR
Configuration: D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
D6M Track-Type Tractor Power Train
Media Number -SENR8387-06 Publication Date -01/11/2010 Date Updated -31/07/2018
i00963997
Final Drive - Install
SMCS - 4050-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8T-3207 Lifting Bracket 1
5P-8622 Shackle 1
6V-9667 Bolt 2
9S-9076 Spacer 2
Illustration 1 g00743487
1/3
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have
the same sealing properties as a new O-ring. A reconditioning procedure should not be
degraded because of a low cost component such as an O-ring or a gasket. Use 1U-6396 O-
Ring Assembly Compound during the assembly procedure.
1. Put O-ring seal (8) in position on the housing.
Illustration 2 g00743488
Illustration 3 g00743489
2. Fasten a suitable lifting device and Tooling (A) to final drive (5).
3. Put the final drive in position on the housing and install bolts (4) and (6).
4. Remove Tooling (A) from the final drive.
2/3
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g00745347
5. Install two bolts (2).
6. Install sprocket segment (1). Torque the bolts to 175 ± 40 N·m (130.0 ± 30.0 lb ft). Torque
the bolts again to 380 N·m (280.0 lb ft).
Note: Refer to Operation and Maintenance Manual, "Lubricant Viscosities and Refill
Capacities" for all fluid capacities and the proper filling procedures.
7. Fill the final drive with oil to the correct level.
End By:
a. Install the axles. Refer to Disassembly and Assembly, "Axle - Remove and Install".
b. Connect the tracks. Refer to Disassembly and Assembly, "Track - Connect".
3/3
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Product: TRACK-TYPE TRACTOR
Model: D6M TRACK-TYPE TRACTOR 6LR
Configuration: D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
D6M Track-Type Tractor Power Train
Media Number -SENR8387-06 Publication Date -01/11/2010 Date Updated -31/07/2018
i00964194
Steering Clutch and Brake - Remove
SMCS - 4100-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8T-3207 Lifting Bracket 1
5P-8622 Shackle 1
6V-9667 Bolt 2
9S-9076 Spacer 2
Start By:
a. Separate the tracks. Refer to Disassembly and Assembly, "Track - Separate".
b. Remove the axles. Refer to Disassembly and Assembly, "Axle - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the oil from the final drive.
Illustration 1 g00745347
2. Turn the final drive until sprocket segment (1) is above the pivot shaft housing. Remove the
bolts and sprocket segment (1).
3. Remove two bolts (2) from the top of the final drive.
Illustration 2 g00747077
4. Adjust bracket (3) on Tooling (A) until the bracket is against the stop on Tooling (A).
2/4
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00743489
Illustration 4 g00743488
5. Fasten Tooling (A) to final drive (5). Fasten a suitable lifting device to Tooling (A).
Note: Do not remove bolts (6) that hold the steering clutch and brake assembly to the final
drive.
6. Remove bolts (4) and (7). Remove the final drive and steering clutch assembly. The weight
of the final drive and steering clutch and brake is 544 kg (1200 lb).
Illustration 5 g00747076
3/4
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 7. Remove O-ring seals (8) and (9) from the housing.
4/4
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Product: TRACK-TYPE TRACTOR
Model: D6M TRACK-TYPE TRACTOR 6LR
Configuration: D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
D6M Track-Type Tractor Power Train
Media Number -SENR8387-06 Publication Date -01/11/2010 Date Updated -31/07/2018
i00964182
Steering Clutch and Brake - Disassemble
SMCS - 4100-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
Start By:
a. Separate the final drive, steering clutches and brakes. Refer to Disassembly and Assembly,
"Final Drive, Steering Clutch, and Brakes - Separate".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Dirt and contaminants can damage the precision components. All disassembly and
assembly procedures must be performed on a clean work surface. Clean all the interior
components in clean solvent. Dry all the interior components with compressed air. Plug ports and
plug hoses on the machine during repair.
1/7
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 4 g00746869
4. Remove clutch plates (5) and friction discs (6) from hub assembly (7).
Illustration 5 g00746870
Illustration 6 g00746872
5. Remove piston (8) from hub assembly (7).
6. Remove sleeve bearing (9).
7. Remove seals (10) and (11) from piston (8).
3/7
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 7 g00746873
8. Turn over the brake assembly.
9. Remove ring (12) from hub assembly (7).
Illustration 8 g00746874
10. Fasten a suitable lifting device and Tooling (A) to housing (13), and remove the brake
assembly from hub assembly (7). The weight of the brake assembly is 86 kg (190.0 lb).
Illustration 9 g00746875
11. Remove bearing (14) from housing (13).
4/7
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 10 g00746876
12. Remove three rings (15) from hub assembly (7).
13. Remove bearing (16) from hub assembly.
Illustration 11 g00746877
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: Bolts (19) hold a spring under compression behind the piston. It is important to
remove bolts (17) before removing bolts (19).
14. Remove bolts (17) and plate (18) from housing (13).
5/7
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 12 g00746878
15. Remove brake plates (20) and friction discs (21) from the housing.
Illustration 13 g00746879
Note: Bolts (19) hold a spring under compression. Loosen bolts (19) slowly and loosen
bolts (19) evenly.
16. Remove bolts (19) and the manifold assembly (22) from housing (13).
Illustration 14 g00746880
17. Remove seals (23) and (24) from manifold assembly (22).
6/7
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 15 g00746881
18. Remove piston (25) from housing (13).
Illustration 16 g00746882
19. Remove springs (26) from housing (13).
Note: Note the direction of spring (26) before removing.
20. Remove O-ring seal (27) and (28).
7/7
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Product: TRACK-TYPE TRACTOR
Model: D6M TRACK-TYPE TRACTOR 6LR
Configuration: D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
D6M Track-Type Tractor Power Train
Media Number -SENR8387-06 Publication Date -01/11/2010 Date Updated -31/07/2018
i00964177
Steering Clutch and Brake - Assemble
SMCS - 4100-016
Assembly Procedure
Table 1
Required Tools
Tool Part number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-510 Driver Group 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the
precision components. All disassembly and all assembly procedures must be performed on a clean
work surface and in a clean area. Keep cleaned parts covered and protected at all times.
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1/9
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g00746882
1. Install springs (26) in housing (13).
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have
the same sealing properties as a new O-ring. A reconditioning procedure should not be
degraded because of a low cost component such as an O-ring or a gasket. Use 1U-6396 O-
Ring Assembly Compound during the assembly procedure.
2. Install O-ring seals (27) and (28).
Illustration 2 g00746973
3. Put piston (25) in position in housing (13).
2/9
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
29. Illustration 3 g00746880
4. Install seals (23) and (24) on manifold assembly (22). Put clean oil on the lip of the seals.
Illustration 4 g00746879
5. Align the oil holes in manifold assembly (22) with the holes in housing (13). Install the
manifold assembly and bolts (19).
Illustration 5 g00746977
This is the correct method in order to make new seal rings ready for installation.
Illustration 6 g00746979
3/9
D6M Track-Type Tractor XL Power Shift 6LR00001-UP (MACHINE) POWERED B...
2021/12/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...