1. Devangkumar Dave
204-20 Sanagan Road, Etobicoke, Ontario, M9V 1R9
Telephone: 647-303-3599 Email: devangkumar.dave@gmail.com
Seeking assignments as a dual tickets with an organisation of repute.
KEY SKILL
• A competent professional and sound experience in electrical field.
• Install, replace and repair electrical control and distribution equipment, such as switches,
relays and circuit breaker panels
• Cable laying, Termination, Cable fault finding.
• Review of engineering drawings, layouts, diagrams, technical specification for trouble
shot the fault for motor and other electrical Machines without effect to the production.
• Exposure in maintenance operations for reducing breakdown / break downtime and
enhancing operational effectiveness of plant equipments.
• Responding to breakdowns and working well under pressure
• Erection and commissioning work for Substation up to 400kV with SCADA system.
• Maintain, repair, test and install electrical motors, generators, industrial storage batteries
and hydraulic and pneumatic electrical control systems.
• Operate, Maintain and Maximize repair of power distribution systems up to 25 kV to
400kV and Low voltage as well.
• Operate, Maintain and Maximize repair of electrical equipment and controls for motors,
motor starters, VFD's, UPS, transformers, heat tracing.
• Operate, Maintain and Maximize repair of instrument equipment and controls i.e.
transmitters, flow meters, control valves,
• Operate, Maintain and Maximize repair of PLC control systems;
• Install new/upgrade existing electrical/instrument equipment.
• Ensuring compliance with health and safety legislation
EMPLOYMENT EXPERIENCE
Journeyman Electrician – Clear Stream Energy Services 2013 – cont.
Working as a electrician in Nexen Oil and gas project for plant maintenance at Long Lake in Fort
McMurry, Alberta.
• Electrical Heat Trace Monitoring, installation and Trouble shoot for AGU, Orcruid and
other upgrader areas of plant.
• Trouble shoots of other plant machines like motors, fire alarm system panel maintenance.
• Arranging temporary power supply for running and construction work.
• Responding to breakdowns and working well under pressure
• Cable laying, Termination, Cable fault finding with testing equipments.
Site Incharge - ABB Limited 2008 – 2013
• Supervise equipments erection work for Lighting Arrestor, Capacitive voltage
Transformer, Wave trap, Current Transformer, Isolator, Circuit Breaker and Potential
Transformer according to approve single line diagram and the manufacturer specifications.
• Supervise control and relay panels installation work (CRP panels for line protection, Bus
bar protection, Transformer protection with help of ABB make relay like REL-670, REB-
670, RET, REF and REC-670) according to the control room layout drawings.
• Prepare cutting schedule for cable laying work as per approved cable schedule and then
glanding and termination work at equipments and panel side.
• Prepare network for SCADA system for Substation automation.
• Making safety inspections, arrange safety meeting and trainings for contractor staff to
ensuring construction and site safety

2. • Panel wiring for relay and control.
• Lighting fixtures wiring and cabling work and fittings for plant and control room.
• Electrical fault finding with the electrical equipments like Insulation tester, Volt meter,
Multi meter, Clamp meter.
• Installation and maintenance of Motor control device.
Plant Attendant-I - Gujarat State Electricity Co. Ltd 2007-2008
Preventive and break down maintenance work of Semi Automatic 210 MW Coal base Power
Plant.
• Maintenance work for electrical system of boilers auxiliary like Induced Draft fan, Forced
Draft fan, Air Pre heater, Spark gun and wall fan.
• LT and HT motor over hauling up to 6.6kV.
• Maintenance of EOT Crain.
• Maintenance work of Battery sets and charger for DC control supply.
• Maintenance work for control panels and power distribution panels and it’s auxiliary.
• Installation and repair of Plant illumination fixture.
Electrician - Zeeneel Construction and Maintenance 1999-2005
• Maintenance of Electrical control Panels, switching devices used in Electrical Control
Center.
• Installation and maintenance of batteries used in supplying DC power supply for relays in
Control and Protection panels.
• Cables laying and detecting cable faults used for the control panels and Switchgears of
Electrical Sub-stations of the plant.
• Operation and Maintenance of Motor Control Centers, Conveyers ,Packaging m/c
• Power Distribution and PF improving devices used in the Electrical Distribution systems.
• Trouble shooting of Allen Bradley's PLC system, Drives and other PC based Protection
systems used in distribution System
EDUCATION & PROFESSIONAL TRAINING
• Graduate Diploma in Mechanical Engineering 2002
• Graduate Diploma in Electrical Engineering 1997
• Operation Training - 210 MW Wanakbori Coal Base Power Plant 2008
• Sub-Station Equipment Training up to 400 kV- ABB Limited 2010
• 442A (Industrial Electrician) license 2013
• 447A (Instrumentation control Technician ) license 2015
• Construction Safety Training (CSTS) for Alberta 2013
• Confined space and entry Monitor. 2013
• H2S Alive 2013
• Fall Protection 2013
• Obtained Ontario driving license (G).
COMPUTER SKILL
Well versed with MS- Office software (Word, Excel, Power point, outlook), Social networking
and basic Knowledge PCM 600 for SCADA system.