Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex00001 and up)

Service Repair Manual
Models
330D2 and 330D2 L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D2 EXCAVATOR FEX
Configuration: 330D2 L Excavator FEX00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i02606369
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 154-6181 Forcing Screw 1
D 138-7574 Link Bracket 2
E
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F 1U-8846 Gasket Sealant 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
1/11(W)
w
2020/7/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
2/11(W)
w
2020/7/17

5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
3/11(W)
w
2020/7/17

10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
4/11(W)
w
2020/7/17

d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
13. Remove sun gear (14) from carrier assembly (15).
14. Remove spacer (16).
5/11(W)
w
2020/7/17

Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
16. Use a screwdriver or a chisel in order to separate the two ring gears (17).
Note: The two ring gears are held together with Tooling (F). It may be necessary to heat the
ring gears in order to soften the sealant. Do not heat over 135 °C (275 °F) for more than
thirty minutes.
6/11(W)
w
2020/7/17

17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
7/11(W)
w
2020/7/17

b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
22. Remove O-ring seal (24) from main housing (18).
8/11(W)
w
2020/7/17

23. Remove bolts (25) from gear (26).
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from the main housing (18) once gear (26) is
removed. Make sure that the motor housing is supported.
25. Remove shims (27) from the main housing.
9/11(W)
w
2020/7/17

26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from the motor housing (28). The combined weight of main housing (18) and the
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
10/11(W)
w
2020/7/17

30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 17 19:51:04 UTC+0800 2020
11/11(W)
w
2020/7/17

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i03508206
SMCS - 4050-015
Table 1
Required Tools
C 1P-1863 Retaining Ring Pliers 1
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 138-7576 Link Bracket 2
Start By:
a. Start by removing the final drive. Refer to Disassembly and Assembly, "Final Drive -
Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
parts must be reinstalled to the original locations.
1/12(W)
w
2020/7/17

2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto
Tooling (A). The weight of the final drive assembly is approximately 550 kg (1200 lb).
3. Remove bolts (1).
4. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
2/12(W)
w
2020/7/17

5. Remove bolts (3) and gear (4). Check plate (6). Replace plate (6) if plate (6) is worn.
Remove plugs (5) from cover (2).
6. Remove O-ring seals (7) from plugs (5).
7. Remove gear (8) and spacer (9).
3/12(W)
w
2020/7/17

8. Use Tooling (C) to remove retaining ring (10). Remove washer (11) and gear (12). Remove
bearing assembly (13) and washer (14).
9. Repeat Step 8 for the other two gear assemblies.
10. Remove retaining ring (15).
11. Remove carrier assembly (16).
4/12(W)
w
2020/7/17

12. Use a suitable press to remove the shafts from carrier assembly (16).
13. Remove gear (17) and spacer (18).
5/12(W)
w
2020/7/17

14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19). The weight of
planetary carrier (19) is approximately 48 kg (105 lb).
15. Remove retaining ring (21). Lift planetary carrier (19) off sun gear (20).
16. Drive spring pin (23) into planetary shaft (22).
6/12(W)
w
2020/7/17

17. Remove planetary shaft (22). Use a suitable punch to remove spring pin (23) from planetary
shaft (22).
18. Remove washers (24) and bearing (25) from planetary gear (26).
19. Repeat Steps 16 through 18 for the other two planetary gears.
20. Remove gear (27). Remove spacer (27A).
7/12(W)
w
2020/7/17

21. Use two people to remove carrier assembly (28). The weight of carrier assembly (28) is
22. Drive spring pin (30) into shaft (29).
23. Remove shaft (29). Use a suitable punch to remove spring pin (30) from shaft (29).
24. Remove washers (31) and bearings (32) from planetary gear (33).
8/12(W)
w
2020/7/17

25. Repeat Steps 22 through 24 for the other three planetary gears.
26. Fasten Tooling (E) and a suitable lifting device to ring gear (34), as shown. Remove ring
gear (34) from sprocket housing (35). The weight of ring gear (34) is approximately 66 kg
(146 lb).
27. Remove O-ring seal (36) from sprocket housing (35).
9/12(W)
w
2020/7/17

28. Remove bolts (37) from coupling gear (38).
29. Install suitable forcing bolts (39) in coupling gear (38). Tighten the forcing bolts evenly in
order to loosen coupling gear (38). Remove the coupling gear from the motor housing.
30. Remove shims (40) from the motor housing.
10/12(W)
w
2020/7/17

Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.
31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Separate the
sprocket housing from the motor housing. The weight of sprocket housing (35) is
32. Remove the locating pins from the motor housing.
33. Remove Duo-Cone seal (41) from the motor housing.
34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
35. Remove Duo-Cone seal (43) from the sprocket housing.
36. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.
37. Remove the bearing cups from the sprocket housing.
Fri Jul 17 19:52:00 UTC+0800 2020
11/12(W)
w
2020/7/17

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05453130
SMCS - 4050-015
S/N - DTG1-UP
S/N - EBP1-UP
S/N - EX71-UP
S/N - FEX1-UP
S/N - HSP1-UP
S/N - JFG1-UP
S/N - KER1-UP
S/N - LJE1-UP
Table 1
Required Tools
C 154-6181 Forcing Bolt 1
E 5F-7366 Forcing Bolt 1
1/11(W)
w
2020/7/17

1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F - Loctite 5127 1
Start By:
a. Remove the final drive.
Note: Cleanliness is an important factor. Before the disassembly procedure, thoroughly
clean the exterior of the component. This action will prevent dirt from entering the internal
mechanism.
parts must be reinstalled in the original locations.
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
3. Remove bolts (1) and the washers that hold the cover in position.
2/11(W)
w
2020/7/17

4. Remove the setscrews from cover (2), and fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
3/11(W)
w
2020/7/17

Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex00001 and up)

Recommended

Recommended

More Related Content

Similar to Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex00001 and up)

Similar to Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex00001 and up) (11)

More from cdfzxs

More from cdfzxs (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex00001 and up)