This document provides instructions for separating the upper frame and undercarriage frame on an M318C wheeled excavator. It lists the required tools which include electric hydraulic pumps, cylinders, stands, pins, tubes, collars, saddles, links and guide bolts. The procedure involves using the listed tools and hydraulic jacks to lift and support the frames while removing connecting components. Proper containment of fluids is noted as important during the separation process.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
2. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M318C WHEELED EXCAVATOR BCZ
Configuration: M318C Excavator BCZ00001-02000 (MACHINE) POWERED BY 3056 Engine
Disassembly and Assembly
M318C Excavator Machine Systems
Media Number -RENR6676-06 Publication Date -01/12/2006 Date Updated -05/12/2006
i03484340
Swing Drive - Assemble
SMCS - 5459-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0510 Driver Gp 1
C 1U-8759 Plier Tips 1
D 5P-4758 Retaining Ring Pliers 1
E 1P-1859 Retaining Ring Pliers 1
F 1P-1855 Retaining Ring Pliers 1
H 1P-1863 Retaining Ring Pliers 1
J
305-4538 Spanner Socket(1)
1
240-8274 Insert(2)
1
174-9465 Spanner Socket(3)
1
K 1P-0520 Driver Gp 1
L 2S-3230 Bearing Lubricant 1
M 8T-5096 Dial Indicator Gp 1
N 7H-1680 Lubrication Hand Pump 1
(1)
Used on the part number 152-7372 Swing Drive Gp
1/12(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. (2)
Used on the part number 152-7372 Swing Drive Gp
(3)
Used on the part number 152-7375 Swing Drive Gp
Note: Replace all O-ring seals and all gaskets. Apply a light film of "10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01027198
1. Lower the temperature of bearing cup (39). Use Tooling (K) to install bearing cup (39) in
swing drive housing (33A).
Illustration 2 g00906881
2. Lower the temperature of bearing cup (36). Use Tooling (K) to install bearing cup (36).
3. Use Tooling (B) to install lip seal (35). Install seal (34). Install tooling (L) to seal (34).
2/12(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. Illustration 3 g01026650
4. Raise the temperature of bearing cone (37). Install washer (38) and bearing cone (37) on
pinion (33).
Illustration 4 g01027078
Illustration 5 g01026558
5. The following steps should be used on machines that are equipped with the part number 152
-7372 Swing Drive Gp.
a. Apply 80 grams of Tooling (L) to the bearing cone on pinion (33). Install pinion (33)
in swing drive housing (33A).
3/12(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. b. Raise the temperature of bearing cone (32A). Install bearing cone (32A).
c. Install nut (32). Use Tooling (J) in order to tighten nut (32) until a slight increase in
rolling torque is obtained. Loosen nut (32) by approximately 60 degrees. Strike pinion
(33) with a soft hammer in order to release the bearing preload.
d. Determine the initial rolling torque of pinion (33). The specified rolling torque is
8 N·m (71 lb in) to 15 N·m (133 lb in). Record this value as Rolling Torque (Y).
e. As you tighten nut (32) rotate swing drive housing (33A) in order to ensure that the
bearings are seated properly. Use Tooling (J) in order to tighten nut (32) to a torque of
300 N·m (221 lb ft). Loosen nut (32) by 30 degrees to 60 degrees.
f. Install ring (31).
g. Install nut (30). Use Tooling (J) in order to tighten nut (30) to a torque of
1000 ± 100 N·m (738 ± 74 lb ft).
h. Determine the rolling torque of pinion (33). The specified rolling torque is Rolling
Torque (Y) plus 3 N·m (27 lb in) to 9 N·m (80 lb in).
6. The following steps should be used on machines that are equipped with the part number 152
-7375 Swing Drive Gp.
a. Apply 80 grams of Tooling (L) to the bearing cone on pinion (33). Install pinion (33)
in swing drive housing (33A).
b. Raise the temperature of bearing cone (32A). Install bearing cone (32A).
c. Install nut (32). Use Tooling (J) in order to tighten nut (32) until a slight increase in
rolling torque is obtained. Loosen nut (32) by approximately 60 degrees. Strike pinion
(33) with a soft hammer in order to release the bearing preload.
d. Determine the initial rolling torque of pinion (33). The specified rolling torque is
6 N·m (53 lb in) to 8 N·m (71 lb in). Record this value as Rolling Torque (Y).
e. As you tighten nut (32) rotate swing drive housing (33A) in order to ensure that the
bearings are seated properly. Use Tooling (J) in order to tighten nut (32) to a torque of
250 ± 50 N·m (184 ± 37 lb ft). Loosen nut (32) by 15 degrees to 30 degrees.
f. Install ring (31).
g. Install nut (30). Use Tooling (J) in order to tighten nut (30) to a torque of
700 ± 50 N·m (516 ± 37 lb ft).
h. Determine the rolling torque of pinion (33). The specified rolling torque is Rolling
Torque (Y) plus 2 N·m (18 lb in) to 5 N·m (44 lb in).
4/12(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. Illustration 6 g00907108
Illustration 7 g00907110
Illustration 8 g01027098
7. Install carrier (27A).
8. Install shim (28). Use Tooling (H) to install retaining ring (27).
9. Raise temperature of bearing race (29). Install bearing race (29) and needle bearings (26).
10. Apply Tooling (L) to the rollers. Install the rollers on bearing race (29). Install gears (25)
over bearing race (29) and the rollers.
5/12(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. 11. Install retaining ring (23) and bearing (24).
Illustration 9 g00906330
12. Install washers (22) and sun gear (21) onto top carrier (11).
Illustration 10 g00906329
13. Use Tooling (E) to install retaining ring (20) onto top carrier (11).
Illustration 11 g00906327
14. Install needle bearings (16), washers (17) and (18), gears (15), and pins (19).
6/12(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Illustration 12 g00906325
15. Use Tooling (F) to install retaining ring (14). Install bearing (13).
Illustration 13 g00906324
16. Install top carrier (11) and shaft (10) in shaft drive (12).
Illustration 14 g00906322
17. Install seals (9) in the swing brake assembly.
7/12(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. Illustration 15 g00909400
18. Use Tooling (B) to install piston (8) in swing brake assembly (2).
Illustration 16 g00906319
19. If equipped, install ring (7).
Illustration 17 g00909004
8/12(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
20. Install spring (6A) and the shim.
21. Use Tooling (K) and a suitable press in order to compress spring (6A). Use Tooling (D) in
order to install retaining ring (6). Rotate the opening in retaining ring (6) by approximately
180 degrees from the notch in swing brake assembly (2).
Illustration 18 g00906314
22. Install discs and plates (5) into swing brake assembly (2).
Illustration 19 g00906313
23. Install plate (4).
9/12(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Illustration 20 g00906311
Illustration 21 g00909003
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Use Tooling (B) and a suitable press in order to compress the spring. Use Tooling (C) to
install retaining ring (3).
10/12(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Illustration 22 g01822733
25. Position Tooling (M) in order to measure the travel of piston (8). Connect Tooling (N) to
Port (P). Use Tooling (N) in order to apply 3000 kPa (435 psi) at Port (P). Record the
measured travel of piston (8) as Dimension (X).
a. The recorded Dimension (X) should be 1.2 mm (0.05 inch) to 1.4 mm (0.06 inch) on
machines that are equipped with the part number 152-7372 Swing Drive Gp.
b. The recorded Dimension (X) should be 1.1 mm (0.04 inch) to 1.3 mm (0.05 inch) on
machines that are equipped with the part number 152-7375 Swing Drive Gp.
Note: Outer plate (5) is available in different thicknesses. Use the correct thickness of
plate (5) in order to obtain the correct Dimension (X).
Illustration 23 g01027113
26. Install Tooling (A) and a suitable lifting device to swing brake assembly (2). The weight of
swing brake assembly (2) is approximately 75 kg (165 lb).
27. Position swing brake assembly (2) in swing brake housing (2A).
11/12(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. 28. Install bolts (1).
End By:
a. Install the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Apr 4 10:30:46 UTC+0800 2020
12/12(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M318C WHEELED EXCAVATOR BCZ
Configuration: M318C Excavator BCZ00001-02000 (MACHINE) POWERED BY 3056 Engine
Disassembly and Assembly
M318C Excavator Machine Systems
Media Number -RENR6676-06 Publication Date -01/12/2006 Date Updated -05/12/2006
i01808092
Swing Drive - Install
SMCS - 5459-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 138-7575 Link Bracket 2
Illustration 1 g00924415
1. Attach Tooling (B) and a suitable lifting device to swing drive (5) .
2. Position swing drive (5). The weight of the swing drive is approximately 75 kg (165 lb).
3. Install bolts (4) .
1/2(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. 4. Connect hose assembly (3) .
Illustration 2 g00924414
5. Connect hose assemblies (2) .
Illustration 3 g00924412
6. Connect hose assemblies (1) .
End By: Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Apr 4 10:31:49 UTC+0800 2020
2/2(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M318C WHEELED EXCAVATOR BCZ
Configuration: M318C Excavator BCZ00001-02000 (MACHINE) POWERED BY 3056 Engine
Disassembly and Assembly
M318C Excavator Machine Systems
Media Number -RENR6676-06 Publication Date -01/12/2006 Date Updated -05/12/2006
i01836133
Upper Frame and Undercarriage Frame - Separate
SMCS - 4150-076; 7051-076
Separation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
3S-6224 Electric Hydraulic Pump Gp 1
8S-7650 Cylinder As 1
4C-6486 Stand 1
8S-7615 Pin 2
8S-7641 Tube 1
8S-7625 Collar 1
8S-8048 Saddle 1
B
3S-6224 Electric Hydraulic Pump Gp 1
8S-7650 Cylinder As 2
4C-6486 Stand 2
8S-7615 Pin 4
8S-7641 Tube 2
8S-7625 Collar 2
9U-6727 Hydraulic Jack Hose Gp 1
C FT-2447 Link 1
1/6(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. D
4C-6486 Stand 2
8S-7615 Pin 2
8S-7641 Tube 2
F Guide Bolt (M20 X 2.5 X 200mm) 4
Start By:
A. Remove the bucket. Refer to Disassembly and Assembly, "Bucket - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Position the machine on a hard level surface. Position the upper structure 90 degrees to the
undercarriage.
Illustration 1 g00937868
2. Fully extend the fore boom cylinder. Fully extend the stick cylinder. Center Tooling (A)
under the stick.
2/6(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. 3. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Presure - Release".
4. Drain the hydraulic oil tank. The hydraulic oil tank contains approximately 170 L (44.9 US
gal).
Illustration 2 g00937869
5. Position Tooling (B) under the counterweight.
Illustration 3 g00937872
6. Raise Tooling (A) until Tooling (A) comes in contact with the stick. Raise Tooling (B) in
order to contact the counterweight. Place wood blocks around the tires.
3/6(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. Illustration 4 g00937874
7. Remove the right hand boom cylinder from the machine. Refer to Disassembly and
Assembly, "Boom Cylinder - Remove and Install".
8. Install Tooling (C) .
9. Use five bolts in order to hold Tooling (C) together.
Illustration 5 g00937876
10. Disconnect hose assemblies (4) from connector (3) .
11. Disconnect hose assemblies (6) from rotor (5) .
12. Disconnect harness assembly (1) .
13. Remove bolts (2) .
14. Attach a suitable lifting device to swivel group (12). The weight of the swivel group is
approximately 84 kg (185 lb).
15. Raise swivel group (12) 305 mm (12 inch) above the main frame. Secure the swivel group
in the raised position. Remove the hoist from the swivel group.
4/6(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 6 g00937877
16. Place alignment marks on the upper structure and the undercarriage for installation
purposes.
17. Disconnect tube assembly (7) from the swing gear and bearing (9) .
18. Remove four bolts (8). The bolts need to be removed 90 degrees from each other.
19. Install Tooling (F) .
20. Remove the remaining bolts (8) .
Illustration 7 g00937878
5/6(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Illustration 8 g00937879
Note: It is important to keep the upper structure level when the upper structure is being
separated.
21. Use Tooling (A) and Tooling (B) in order to raise upper structure (10) from undercarriage
(11). Adjust Tooling (A) and Tooling (B) in order to obtain the clearance. Remove
undercarriage (11). The weight of the upper structure is approximately 8740 kg (19,270 lb).
22. Install Tooling (D) under the counterweight for additional support.
Illustration 9 g00937880
23. Attach a suitable device in order to pull undercarriage (11). Remove the wood blocks from
the tires. Pull undercarriage (11) with a lift truck. The weight of the undercarriage is
approximately 6000 kg (13,230 lb).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Apr 4 10:32:52 UTC+0800 2020
6/6(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M318C WHEELED EXCAVATOR BCZ
Configuration: M318C Excavator BCZ00001-02000 (MACHINE) POWERED BY 3056 Engine
Disassembly and Assembly
M318C Excavator Machine Systems
Media Number -RENR6676-06 Publication Date -01/12/2006 Date Updated -05/12/2006
i01836134
Upper Frame and Undercarriage Frame - Connect
SMCS - 4150-077; 7051-077
Connection Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
3S-6224 Electric Hydraulic Pump Gp 1
8S-7650 Cylinder As 1
4C-6486 Stand 1
8S-7615 Pin 2
8S-7641 Tube 1
8S-7625 Collar 1
8S-8048 Saddle 1
B
3S-6224 Electric Hydraulic Pump Gp 1
8S-7650 Cylinder As 2
4C-6486 Stand 2
8S-7615 Pin 4
8S-7641 Tube 2
8S-7625 Collar 2
9U-6727 Hydraulic Jack Hose Gp 1
C FT-2447 Link 1
1/5(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. D
4C-6486 Stand 2
8S-7615 Pin 2
8S-7641 Tube 2
F Guide Bolt ( M20 X 2.5 X 200mm) 4
G
4C-9564 Wrench 1
6V-3146 Extension 1
6V-4170 Adapter 1
9S-7351 Torque Wrench 1
H 4C-5593 Anti-Seize Compound 1
J 1U-8846 Gasket Sealant 1
1. Install Tooling (F) .
2. Apply Tooling (H) to bolts (14) .
3. Apply Tooling (J) on the mating surfaces of the upper structure and the undercarriage.
4. Position undercarriage (11) .
5. Place wood blocks around the tires.
6. Align the alignment marks on the upper structure and the undercarriage frame.
Illustration 1 g00937878
2/5(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
24. Illustration 2 g00937879
Note: It is important to keep the upper structure level when the upper structure is being
connected.
7. Remove Tooling (D) .
8. Use Tooling (A) and Tooling (B) in order to lower upper structure (10) onto undercarriage
(11). The weight of the upper structure is approximately 8740 kg (19,270 lb).
Illustration 3 g00937877
9. Use Tooling (G) in order to install bolts (8). Tighten bolts (8) to a torque of 649 N·m (479
lb ft).
10. Remove Tooling (F) .
11. Install the remaining bolts (8) .
12. Connect tube assembly (7) onto the swing gear and bearing (9) .
3/5(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
25. Illustration 4 g00937876
13. Attach a suitable lifting device to swivel group (12). The weight of the swivel group is
approximately 84 kg (185 lb).
14. Position swivel group (12) .
15. Install bolts (2) .
16. Connect harness assembly (1) .
17. Connect hose assemblies (6) onto rotor (5) .
18. Connect hose assemblies (4) onto connector (3) .
Illustration 5 g00937874
19. Remove Tooling (C) .
20. Install the right hand boom cylinder from the machine. Refer to Disassembly and Assembly,
"Boom Cylinder - Remove and Install".
4/5(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Illustration 6 g00937872
21. Remove Tooling (A) and Tooling (B) .
22. Fill the hydraulic oil tank. The hydraulic oil tank contains approximately 170 L (44.9 US
gal).
End By: Install the bucket. Refer to Disassembly and Assembly, "Bucket - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Apr 4 10:33:54 UTC+0800 2020
5/5(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
28. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M318C WHEELED EXCAVATOR BCZ
Configuration: M318C Excavator BCZ00001-02000 (MACHINE) POWERED BY 3056 Engine
Disassembly and Assembly
M318C Excavator Machine Systems
Media Number -RENR6676-06 Publication Date -01/12/2006 Date Updated -05/12/2006
i01832450
Hydraulic Tank and Filter - Remove
SMCS - 5056-011; 5068-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-8358 Eyebolt 1
B 138-7573 Link Bracket 1
ZZ
6V-9510 Face Seal Plug 3
6V-9831 Cap As 3
6V-9511 Face Seal Plug 4
6V-9832 Cap As 4
6V-9512 Face Seal Plug 3
6V-9833 Cap As 3
6V-9509 Face Seal Plug 1
6V-9830 Cap As 1
6V-9508 Face Seal Plug 1
6V-9829 Cap As 1
Start By:
A. Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
1/8(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
29. Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
1. Drain the hydraulic tank. The hydraulic tank contains approximately 170 L (50 US gal) of
hydraulic oil.
Illustration 1 g00936049
2. Remove bolts (1) from panel (2) .
Illustration 2 g00936051
3. Remove bolts (3) .
4. Remove panel (2) .
2/8(W)w
2020/4/4https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...